D156 Wide
Product numbers 4415-AB1 4423-AB1 First Edition (June 2008 ) (c) Copyright Lenovo 2008. LENOVO products, data, computer software, and services have been developed exclusively at private expense and are sold to governmental entities as commercial items as defined by 48 C.F.R. 2.101 with limited and restricted rights to use, reproduction and disclosure.
Contents Safety information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iii Chapter1. Getting started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1 Shipping contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Safety information Before installing this product, read the Safety Information.
Chapter 1. Getting started This User’s Guide contains detailed information on the your Flat Panel Monitor. For a quick overview, please see the Setup Poster that was shipped with your monitor.
Product overview This section will provide information on adjusting monitor positions, setting user controls, and using the cable lock slot. Types of adjustments Please see the illustration below for an example of the tilt range. 5 20 User controls Your monitor has controls on the front which are used to adjust the display. For information on how to use these controls, please see “Adjusting your monitor image” on page 2-3.
Setting up your monitor This section provides information on how to set up your monitor. Connecting and turning on your monitor Note: Be sure to read the Safety Information located in the Monitor Safety, Troubleshooting, and Warranty Guide before carrying out this procedure. 1. Power off your computer and all attached devices, and unplug the computer power cord. 2. Connect the analog signal cable to the video port on the back of the computer.
3. Plug the monitor power cord and the computer cord into grounded electrical outlets. 4 Power on the monitor and the computer. .
5. To install the monitor driver ,insert the Reference and Driver CD, click Install driver, and follow the on-screen instructions. 6. To optimize your monitor image, press the Automatic Image Setup key . Automatic image setup requires that the monitor is warmed up for at least 15 minutes. This is not required for normal operation. Note: If automatic image setup does not establish the image that you prefer, perform manual image setup. See “Manual image setup” on page 3-4 . Chapter 1.
Chapter 2. Adjusting and using your monitor This section will give you information on adjusting and using your monitor. Comfort and accessibility Good ergonomic practice is important to get the most from your personal computer and to avoid discomfort. Arrange your workplace and the equipment you use to suit your individual needs and the kind of work that you perform. In addition, use healthy work habits to maximize your performance and comfort while using your computer.
• Use the monitor brightness, contrast, and image adjustment controls, if equipped, to optimize the image on your screen to meet your visual preferences. • Keep your monitor screen clean so you can focus on the screen’s contents. Any concentrated and sustained visual activity can be tiring for your eyes. Be sure to periodically look away from your monitor screen and focus on a far object to allow your eye muscles to relax.
Adjusting your monitor image This section describes the user control features for adjusting your monitor image. Using the direct access controls The direct access controls can be used when the On Screen Display (OSD) is not displayed. Note: The direct access controls are grey. Table 2-1. Direct access controls Icon Control Description Image Setup Activates automatic image adjustment. Brightness Direct access to Brightness adjustment.
Table 2-2. OSD functions OSD Icon on Main Menu Submenu Description Controls and Adjustments (Analog) Adjusts overall brightness Brightness/ Contrast Brightness Adjusts difference between light and dark areas Contrast Moves the image left or right. Image Position Horizontal Position Vertical Position Moves the image up or down. Automatically optimizes the image. Image Setup Automatic Manual Manually optimizes the image. See “Manual image setup” on page 3-4.
Table 2-2. OSD functions OSD Icon on Main Menu Submenu Description Shows resolution, refresh rate, and product details. Options Information Menu Language Menu Position Reset Accessibility Note: This screen does not allow any changes to the settings. This section lists the languages supported by your monitor. Note: The language chosen only affects the language of the OSD. It has no effect on any software running on the computer. Menu position adjusts menu location on the screen.
Selecting a supported display mode The display mode the monitor uses is controlled by the computer. Therefore, refer to your computer documentation for details on how to change display modes. The image size, position and shape might change when the display mode changes. This is normal and the image can be readjusted using automatic image setup and the image controls. Unlike CRT monitors, which require a high refresh rate to minimize flicker, LCD or Flat Panel technology is inherently flicker-free.
Understanding power management Power management is invoked when the computer recognizes that you have not used your mouse or keyboard for a user-definable period. There are several states as described in the table below. For optimal performance, switch off your monitor at the end of each working day, or whenever you expect to leave it unused for long periods during the day. Table 2-4.
Caring for your monitor Be sure to turn off the power before you perform any maintenance on the monitor. Do not: • Apply water or liquid directly to your monitor. • Use solvents or abrasives. • Use flammable cleaning materials to clean your monitor or any other electrical equipment. • Touch the screen area of your monitor with sharp or abrasive items. This type of contact may cause permanent damage to your screen. • Use any cleaner which contains an anti-static solution or similar additives.
Chapter 3. Reference information This section contains monitor specifications, instructions to manually install the monitor driver, troubleshooting information, and service information. Monitor specifications Table 3-1. Monitor specifications Dimensions Height 295.454 mm (12.1685 in.) Depth 189.667 mm (7.4671 in.) Width 374.046 mm (14.7262 in.) Stand Tilt Range: -5q, +20q VESA mount Supported Image Viewable image size 395 mm (15.6 in.) Maximum height 193.536 mm (7.6 in.
Table 3-1.
Troubleshooting If you have a problem setting up or using your monitor, you might be able to solve it yourself. Before calling your dealer or Lenovo, try the suggested actions that are appropriate to your problem. Table 3-2. Troubleshooting Problem Possible cause Suggested action Reference The words "Out of Range" are shown on the screen, and the power indicator is flashing green. The system is set to a display mode which is not supported by the monitor.
Table 3-2. Troubleshooting Problem Possible cause Suggested action Reference The power indicator is green, but there is no image. The video signal cable is loose or disconnected from the system or monitor. Be sure the video cable is connected with the system properly. “Connecting and turning on your monitor” on page 1-3 The monitor brightness and contrast are at the lowest setting. Adjust the brightness and contrast setting on the OSD menu.
Manually installing the monitor driver Below are steps for manually installing the monitor driver in Microsoft Windows Vista, Microsoft. Windows XP. Installing the monitor driver in Windows Vista To install the device driver in Microsoft® Windows Vista, do the following: Note: You must download files from the Lenovo Monitor CD to use the Plug and Play feature in Windows Vista. 1. Turn off the computer and all attached devices. 2. Ensure that the monitor is connected correctly. 3.
Installing the monitor driver in Windows XP To use the Plug and Play feature in Windows XP, files should be loaded from the Reference and Driver CD. Note: This section must be completed before continuing with the Windows XP automatic image setup. 1. Turn off the computer and all attached devices. 2. Ensure that the monitor is connected correctly. 3. Turn on the monitor and then the system unit. Allow the system to boot into Windows XP. 4.
Service information Product numbers The product number for your monitor is located on the side of the display bezel as shown below. Customer responsibilities The warranty does not apply to a product which has been damaged due to accident, misuse, abuse, improper installation, usage not in accordance with product specifications and instructions, natural or personal disaster, or unauthorized alterations, repairs or modifications.
Service parts The following parts are for use by Lenovo service, or Lenovo authorized dealers, to support the customer warranty. Parts are for service use only. The table below shows information for model D156Wide Table 3-3. List of service parts RELEASE DESCRIPTION D156wide FRU monitor 45J7678 D156wide FRU Stand 45J7679 30R5139 D156wide FRU Signal cable (Analog, 1.
Appendix A. Service and Support The following information describes the technical support that is available for your product, during the warranty period or throughout the life of the product. Refer to your Lenovo Statement of Limited Warranty for a full explanation of Lenovo warranty terms. Online technical support Online technical support is available during the life of your product through the L enovo Support Web site at http:/ / www.lenovo.com/ think/ support.
Country or Region Telephone Number Austria Up and running support: 01-24592-5901 Warranty service and support: 01-211-454-610 (German) Belgium Up and running support: 02-210-9820 (Dutch) Up and running support: 02-210-9800 (French) Warranty service and support: 02-225-3611 (Dutch, French) Bolivia 0800-0189 (Spanish) Brazil Sao Paulo region: (11) 3889-8986 Toll free outside Sao Paulo region: 0800-7014-815 (Brazilian Portuguese) Canada 1-800-565-3344 (English, French) In Toronto only call: 416-383-
Country or Region Telephone Number Hungary +36-1-382-5720 India 1600-44-6666 Alternate Toll Free: +91-80-2678-8940 (English) Indonesia 800-140-3555 +62-21-251-2955 (English, Bahasa, Indonesian) Ireland Up and running support: 01-815-9202 Warranty service and support: 01-881-1444 (English) Italy Up and running support: 02-7031-6101 Warranty service and support: +39-800-820094 (Italian) Japan Desktop: Toll free: 0120-887-870 For International: +81-46-266-4724 ThinkPad: Toll free: 0120-887-874 For
Country or Region Telephone Number Poland +48-22-878-6999 Portugal +351-21-892-7147 (Portuguese) Romania +4-021-224-4015 Russian Federation +7-095-940-2000 (Russian) Singapore 1800-3172-888 (English, Bahasa, Melayu) Slovakia +421-2-4954-1217 Slovenia +386-1-4796-699 Spain 91-714-7983 91-397-6503 (Spanish) Sri Lanka +94-11-2448-442 (English) Sweden Up and running support: 08-477-4420 Warranty service and support: 077-117-1040 (Swedish) Switzerland Up and running support: 058-333-0900 W
Appendix B. Notices Lenovo may not offer the products, services, or features discussed in this document in all countries. Consult your local Lenovo representative for information on the products and services currently available in your area. Any reference to a Lenovo product, program, or service is not intended to state or imply that only that Lenovo product, program, or service may be used.
Trademarks The following terms are trademarks of Lenovo in the United States, other countries, or both: Lenovo Lenovo logo ThinkPad Thinkvision ENERGY STAR and the ENERGY STAR logo are registered US trademarks. Microsoft and Windows are trademarks of Microsoft Corporation in the United States, other countries, or both. Other company, product, or service names may be trademarks or service marks of others.
