Hardware Maintenance Manual Machine Types: 6531, 6532, 6533, and 6534.
Hardware Maintenance Manual Machine Types: 6531, 6532, 6533, and 6534.
Note: Before using this information and the product it supports, read the general information in Appendix A “Notices” on page 221 and the Warranty and Support Information document on the ThinkServer Documentation DVD. Third Edition (September 2010) © Copyright Lenovo 2009, 2010. LENOVO products, data, computer software, and services have been developed exclusively at private expense and are sold to governmental entities as commercial items as defined by 48 C.F.R. 2.
Contents Chapter 1. About this manual . . . . . 1 Important Safety Information . . . . Safety statements . . . . . . . . Important information about replacing compliant FRUs . . . . . . . . . Turkish statement of compliance . . . . . . . . RoHS . . . . . . . . . . . . 1 2 . . . . . . 5 5 Chapter 2. General information. . . . . 7 Features and technologies Specifications . . . . . Software . . . . . . . EasyStartup . . . . EasyManage. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Replacing a memory module (DIMM) . . . . . . Supported memory types . . . . . . . . Removing a memory module . . . . . . . Installing a memory module . . . . . . . . Replacing hard disk drives . . . . . . . . . . Removing a simple-swap Serial ATA (SATA) hard disk drive . . . . . . . . . . . . . Installing a simple-swap Serial ATA (SATA) hard disk drive . . . . . . . . . . . . . Removing a hot-swap hard disk drive . . . . Installing a hot-swap hard disk drive . . . . Replacing a PCI card . . . . . . . . . .
Before you use the EasyStartup DVD . . . . EasyStartup overview . . . . . . . . . . Installing your operating system without using EasyStartup . . . . . . . . . . . . . . Updating the firmware. . . . . . . . . . . . Using the EasyUpdate Firmware Updater tool . . Starting the backup server firmware . . . . . . Recovering the UEFI firmware. . . . . . . . . Using the integrated management module . . . . IBM Advanced Settings Utility program . . . . . Installing ThinkServer EasyManage software . . .
viii Hardware Maintenance Manual
Chapter 1. About this manual This Hardware Maintenance Manual contains information to help you solve problems that might occur in your server. It describes the diagnostic tools that come with the server, error codes and suggested actions, and instructions for replacing failing components. Replaceable components are of three types: • Self-service customer replaceable unit (CRU): Replacement of self-service CRUs is your responsibility.
Safety statements Important: Each caution and danger statement in this document is labeled with a number. This number is used to cross reference an English-language caution or danger statement with translated versions of the caution or danger statement in the Safety Information document. For example, if a caution statement is labeled "Statement 1," translations for that caution statement are in the Safety Information document under "Statement 1.
• Throw or immerse into water • Heat to more than 100°C (212°F) • Repair or disassemble Dispose of the battery as required by local ordinances or regulations. Statement 3 CAUTION: When laser products (such as CD-ROMs, DVD drives, fiber optic devices, or transmitters) are installed, note the following: • Do not remove the covers. Removing the covers of the laser product could result in exposure to hazardous laser radiation. There are no serviceable parts inside the device.
Statement 5 CAUTION: The power control button on the device and the power switch on the power supply do not turn off the electrical current supplied to the device. The device also might have more than one power cord. To remove all electrical current from the device, ensure that all power cords are disconnected from the power source. 2 1 Statement 8 CAUTION: Never remove the cover on a power supply or any part that has the following label attached.
Important information about replacing RoHS compliant FRUs RoHS, The Restriction of Hazardous Substances in Electrical and Electronic Equipment Directive (2002/95/EC) is a European Union legal requirement affecting the global electronics industry. RoHS requirements must be implemented on Lenovo products placed on the market and sold in the European Union after June 2006. Products on the market before June 2006 are not required to have RoHS compliant parts.
6 Hardware Maintenance Manual
Chapter 2. General information This chapter provides general information that applies to all machine types supported by this publication. Features and technologies The server uses the following features and technologies: • UEFI-compliant server firmware UEFI replaces the basic input/output system (BIOS) and defines a standard interface between the operating system, platform firmware, and external devices. The server design combines the UEFI capabilities and features with legacy BIOS compatibility.
• Large system-memory capability The memory bus supports up to 24 GB of memory when registered DIMMs are installed. The server supports up to 8 GB if unbuffered DIMMs are installed. The memory controller supports error correcting code (ECC) for up to six industry-standard PC3-8500 or PC3-10600R-999, 1066 and 1333 MHz, DDR3 (third-generation double-data-rate), registered or unbuffered, synchronous dynamic random access memory (SDRAM) dual inline memory modules (DIMMs).
– Event logs for RAID controllers and service processors The diagnostics programs create a merged log that includes events from all collected logs. The information is collected into a file that you can send to the Lenovo technical support team to help diagnose a problem. Additionally, you can view the information locally through a generated text report file. You can also copy the log to a removable medium and view the HTML log from a Web browser.
Table 1. Features and specifications Microprocessor: SATA optical drives: • Supports one Intel® quad-core (Xeon 3400 series) or dual-core (Celeron G1101, Pentium G6950, or core i3 series) processor with the IbexPeak 3420 chip set and Multi-chip Package (MCP) processor architecture • UltraSlim DVD-ROM combo (optional) • Designed for LGA 1156 socket One of the following configurations: • Scalable up to four cores • Four 2.
Table 1. Features and specifications (continued) RAID controllers: • An IBM ServeRAID-BR10il SAS/SATA Controller that provides RAID levels 0, 1, and 1E (comes standard on some hot-swap SAS and hot-swap SATA models). • An optional IBM ServeRAID-MR10i SAS/SATA Controller SAS/SATA adapter that provides RAID levels 0, 1, 5, 6, and 10 can be ordered. • An optional IBM ServeRAID-M1015 SAS/SATA controller that provides RAID levels 0,1,10, and 5 can be ordered. Acoustical noise emissions: • Sound power, idling: 6.
EasyStartup The ThinkServer EasyStartup program simplifies the process of configuring your RAID controllers and installing supported ®Microsoft®Windows and Linux operating systems and device drivers on your server. The EasyStartup program is provided with your server on DVD. The DVD is self starting (bootable). The User Guide for the EasyStartup program is on the DVD and can be accessed directly from the program interface. For additional information, see “Using the EasyStartup DVD” on page 207.
Chapter 3. General Checkout You can solve many problems without outside assistance by following the troubleshooting procedures in this Hardware Maintenance Manual and on the Lenovo Web site. This document describes the diagnostic tests that you can perform, troubleshooting procedures, and explanations of error messages and error codes. The documentation that comes with your operating system and software also contains troubleshooting information.
• For intermittent problems, check the error log; see “Event logs” on page 17 and “Diagnostic programs and messages” on page 64. Performing the checkout procedure To perform the checkout procedure, complete the following steps: Step 1. Is the server part of a cluster? • No: Go to step Step 2 “” on page 14. • Yes: Shut down all failing servers that are related to the cluster. Go to step Step 2 “” on page 14. Step 2. Complete the following steps: a.
b. Collect system data. Run the Dynamic System Analysis (DSA) diagnostics program to collect information about the hardware, firmware, software, and operating system. Have this information available when you contact Lenovo or an approved warranty service provider. See “Diagnostic programs and messages” on page 64 for the instructions to run the DSA program. If you need to download the latest version of DSA , go to http://www.lenovo.com/support. 3. Follow the problem-resolution procedures.
c) In the Browse by product window Family: list, select ThinkServer RS210. d) Click Downloads and drivers . e) Click User's guides and manuals to look for related documentation. c. Check for service bulletins.Lenovo service bulletins document known problems and suggested solutions. To search for service bulletins, complete the following steps. 1) Go to: http://www.lenovo.com/support. 2) From the Select your product list, select Servers and Storage.
Chapter 4. Diagnostics This chapter describes the diagnostic tools that are available to help you solve problems that might occur in the server. Diagnostic tools The following tools are available to help you diagnose and solve hardware-related problems: • POST error messages and error logs The power-on self-test (POST) generates messages to indicate successful test completion or the detection of a problem.
• POST event log: This log contains the three most recent error codes and messages that were generated during POST. You can view the POST event log through the Setup utility. • System-event log: This log contains messages that were generated during POST and all system status messages from the service processor. You can view the contents of the system-event log from the Setup utility for more information. The system-event log is limited in size.
Table 2. Methods for viewing event logs (continued) Condition Action The server is hung. • If DSA Preboot is installed, restart the server and press F2 to start DSA Preboot and view the event logs. • If DSA Preboot is not installed, insert the DSA Preboot CD and restart the server to start DSA Preboot and view the event logs. • Alternatively, you can restart the server and press F1 to start the Setup utility and view the POST event log or system-event log.
• Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. • See Chapter 7 “Parts listing, RS210 Types 6531, 6532, 6533, and 6534” on page 175 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU). • If an action step is preceded by “(Trained service technician only),” that step must be performed only by a trained service technician.
• Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. • See Chapter 7 “Parts listing, RS210 Types 6531, 6532, 6533, and 6534” on page 175 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU). • If an action step is preceded by “(Trained service technician only),” that step must be performed only by a trained service technician.
• Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. • See Chapter 7 “Parts listing, RS210 Types 6531, 6532, 6533, and 6534” on page 175 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU). • If an action step is preceded by “(Trained service technician only),” that step must be performed only by a trained service technician.
• Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. • See Chapter 7 “Parts listing, RS210 Types 6531, 6532, 6533, and 6534” on page 175 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU). • If an action step is preceded by “(Trained service technician only),” that step must be performed only by a trained service technician.
• Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. • See Chapter 7 “Parts listing, RS210 Types 6531, 6532, 6533, and 6534” on page 175 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU). • If an action step is preceded by “(Trained service technician only),” that step must be performed only by a trained service technician.
• Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. • See Chapter 7 “Parts listing, RS210 Types 6531, 6532, 6533, and 6534” on page 175 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU). • If an action step is preceded by “(Trained service technician only),” that step must be performed only by a trained service technician.
• Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. • See Chapter 7 “Parts listing, RS210 Types 6531, 6532, 6533, and 6534” on page 175 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU). • If an action step is preceded by “(Trained service technician only),” that step must be performed only by a trained service technician.
Information Information messages do not require action; they record significant system-level events, such as when the server is started. Warning Warning messages do not require immediate action; they indicate possible problems, such as when the recommended maximum ambient temperature is exceeded. Error Error messages might require action; they indicate system errors, such as when a fan is not detected.
• Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. • See Chapter 7 “Parts listing, RS210 Types 6531, 6532, 6533, and 6534” on page 175 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU). • If an action step is preceded by “(Trained service technician only),” that step must be performed only by a trained service technician. The Processor CPU nStatus has Failed with IERR.
• Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. • See Chapter 7 “Parts listing, RS210 Types 6531, 6532, 6533, and 6534” on page 175 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU). • If an action step is preceded by “(Trained service technician only),” that step must be performed only by a trained service technician.
• Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. • See Chapter 7 “Parts listing, RS210 Types 6531, 6532, 6533, and 6534” on page 175 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU). • If an action step is preceded by “(Trained service technician only),” that step must be performed only by a trained service technician.
• Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. • See Chapter 7 “Parts listing, RS210 Types 6531, 6532, 6533, and 6534” on page 175 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU). • If an action step is preceded by “(Trained service technician only),” that step must be performed only by a trained service technician.
• Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. • See Chapter 7 “Parts listing, RS210 Types 6531, 6532, 6533, and 6534” on page 175 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU). • If an action step is preceded by “(Trained service technician only),” that step must be performed only by a trained service technician. Error The System %1 encountered a POST Error.
• Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. • See Chapter 7 “Parts listing, RS210 Types 6531, 6532, 6533, and 6534” on page 175 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU). • If an action step is preceded by “(Trained service technician only),” that step must be performed only by a trained service technician.
• Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. • See Chapter 7 “Parts listing, RS210 Types 6531, 6532, 6533, and 6534” on page 175 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU). • If an action step is preceded by “(Trained service technician only),” that step must be performed only by a trained service technician.
• Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. • See Chapter 7 “Parts listing, RS210 Types 6531, 6532, 6533, and 6534” on page 175 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU). • If an action step is preceded by “(Trained service technician only),” that step must be performed only by a trained service technician. Array %1 is in critical condition.
• Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. • See Chapter 7 “Parts listing, RS210 Types 6531, 6532, 6533, and 6534” on page 175 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU). • If an action step is preceded by “(Trained service technician only),” that step must be performed only by a trained service technician.
• Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. • See Chapter 7 “Parts listing, RS210 Types 6531, 6532, 6533, and 6534” on page 175 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU). • If an action step is preceded by “(Trained service technician only),” that step must be performed only by a trained service technician.
• Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. • See Chapter 7 “Parts listing, RS210 Types 6531, 6532, 6533, and 6534” on page 175 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU). • If an action step is preceded by “(Trained service technician only),” that step must be performed only by a trained service technician. Error A PCI PERR has occurred on system %1.
• Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. • See Chapter 7 “Parts listing, RS210 Types 6531, 6532, 6533, and 6534” on page 175 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU). • If an action step is preceded by “(Trained service technician only),” that step must be performed only by a trained service technician. Error A PCI PERR has occurred on system %1.
• Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. • See Chapter 7 “Parts listing, RS210 Types 6531, 6532, 6533, and 6534” on page 175 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU). • If an action step is preceded by “(Trained service technician only),” that step must be performed only by a trained service technician. Error Fault in slot System board on system %1.
• Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. • See Chapter 7 “Parts listing, RS210 Types 6531, 6532, 6533, and 6534” on page 175 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU). • If an action step is preceded by “(Trained service technician only),” that step must be performed only by a trained service technician.
• Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. • See Chapter 7 “Parts listing, RS210 Types 6531, 6532, 6533, and 6534” on page 175 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU). • If an action step is preceded by “(Trained service technician only),” that step must be performed only by a trained service technician.
• Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. • See Chapter 7 “Parts listing, RS210 Types 6531, 6532, 6533, and 6534” on page 175 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU). • If an action step is preceded by “(Trained service technician only),” that step must be performed only by a trained service technician.
• Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. • See Chapter 7 “Parts listing, RS210 Types 6531, 6532, 6533, and 6534” on page 175 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU). • If an action step is preceded by “(Trained service technician only),” that step must be performed only by a trained service technician. Watchdog %1 Failed to Capture Screen.
• Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. • See Chapter 7 “Parts listing, RS210 Types 6531, 6532, 6533, and 6534” on page 175 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU). • If an action step is preceded by “(Trained service technician only),” that step must be performed only by a trained service technician.
• Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. • See Chapter 7 “Parts listing, RS210 Types 6531, 6532, 6533, and 6534” on page 175 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU). • If an action step is preceded by “(Trained service technician only),” that step must be performed only by a trained service technician. IMM Test Alert Generated by %1.
DVD drive problems • Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. • See Chapter 7 “Parts listing, RS210 Types 6531, 6532, 6533, and 6534” on page 175 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU). • If an action step is preceded by “(Trained service technician only),” that step must be performed only by a Trained service technician.
General problems • Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. • See Chapter 7 “Parts listing, RS210 Types 6531, 6532, 6533, and 6534” on page 175 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU). • If an action step is preceded by “(Trained service technician only),” that step must be performed only by a Trained service technician.
• Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. • See Chapter 7 “Parts listing, RS210 Types 6531, 6532, 6533, and 6534” on page 175 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU). • If an action step is preceded by “(Trained service technician only),” that step must be performed only by a Trained service technician.
• Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. • See Chapter 7 “Parts listing, RS210 Types 6531, 6532, 6533, and 6534” on page 175 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU). • If an action step is preceded by “(Trained service technician only),” that step must be performed only by a Trained service technician.
Intermittent problems • Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. • See Chapter 7 “Parts listing, RS210 Types 6531, 6532, 6533, and 6534” on page 175 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU). • If an action step is preceded by “(Trained service technician only),” that step must be performed only by a Trained service technician.
Keyboard, mouse, or pointing-device problems • Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. • See Chapter 7 “Parts listing, RS210 Types 6531, 6532, 6533, and 6534” on page 175 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU). • If an action step is preceded by “(Trained service technician only),” that step must be performed only by a Trained service technician.
Memory problems • Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. • See Chapter 7 “Parts listing, RS210 Types 6531, 6532, 6533, and 6534” on page 175 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU). • If an action step is preceded by “(Trained service technician only),” that step must be performed only by a Trained service technician.
Microprocessor problems • Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. • See Chapter 7 “Parts listing, RS210 Types 6531, 6532, 6533, and 6534” on page 175 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU). • If an action step is preceded by “(Trained service technician only),” that step must be performed only by a Trained service technician.
• Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. • See Chapter 7 “Parts listing, RS210 Types 6531, 6532, 6533, and 6534” on page 175 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU). • If an action step is preceded by “(Trained service technician only),” that step must be performed only by a Trained service technician.
• Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. • See Chapter 7 “Parts listing, RS210 Types 6531, 6532, 6533, and 6534” on page 175 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU). • If an action step is preceded by “(Trained service technician only),” that step must be performed only by a Trained service technician.
Optional-device problems • Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. • See Chapter 7 “Parts listing, RS210 Types 6531, 6532, 6533, and 6534” on page 175 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU). • If an action step is preceded by “(Trained service technician only),” that step must be performed only by a Trained service technician.
Power problems • Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. • See Chapter 7 “Parts listing, RS210 Types 6531, 6532, 6533, and 6534” on page 175 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU). • If an action step is preceded by “(Trained service technician only),” that step must be performed only by a Trained service technician.
• Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. • See Chapter 7 “Parts listing, RS210 Types 6531, 6532, 6533, and 6534” on page 175 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU). • If an action step is preceded by “(Trained service technician only),” that step must be performed only by a Trained service technician.
• Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. • See Chapter 7 “Parts listing, RS210 Types 6531, 6532, 6533, and 6534” on page 175 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU). • If an action step is preceded by “(Trained service technician only),” that step must be performed only by a Trained service technician.
Universal Serial Bus (USB) port problems • Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. • See Chapter 7 “Parts listing, RS210 Types 6531, 6532, 6533, and 6534” on page 175 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU). • If an action step is preceded by “(Trained service technician only),” that step must be performed only by a Trained service technician.
3. Remove the server cover and look inside the server for lit LEDs. Certain components inside the server have LEDs that will be lit to indicate the location of a problem. For example, a DIMM error will light the LED next to the failing DIMM on the system board. Look at the system service label inside the side cover of the server, which gives an overview of internal components. This information can often provide enough information to correct the error.
• Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. • See Chapter 7 “Parts listing, RS210 Types 6531, 6532, 6533, and 6534” on page 175 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU). • If an action step is preceded by “(Trained service technician only),” that step must be performed only by a trained service technician.
System pulse LEDs The following LEDs are on the system board and indicates the system power-on and power-off sequencing and boot progress (see “System-board LEDs” on page 112 for the location of these LEDs). Table 4. System pulse LEDs LED Description Action Enclosure manager heartbeat power-on and power-off sequencing. 1. If the LED flashes at 1Hz, it is functioning properly and no action is necessary. 2. If the LED is not flashing, (trained service technician only) replace the system board.
Note: Changes are made periodically to the Lenovo Web site. The actual procedure might vary slightly from what is described in this document. Go to http://www.lenovo.com/support. Utilities are available to reset and update the diagnostics code on the integrated USB flash device, if the diagnostic partition becomes damaged and does not start the diagnostic programs. For more information and to download the utilities, go to http://www.lenovo.com/support.
Viewing the test log To view the test log when the tests are completed, type the view command in the DSA interactive menu, or select Diagnostic Event Log in the graphical user interface. To transfer DSA Preboot collections to an external USB device, type the copy command in the DSA interactive menu. Diagnostic messages The following table describes the messages that the diagnostic programs might generate and suggested actions to correct the detected problems.
Table 5. DSA Preboot messages (continued) • Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. • See Chapter 7 “Parts listing, RS210 Types 6531, 6532, 6533, and 6534” on page 175 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU). • If an action step is preceded by “(Trained service technician only),” that step must be performed only by a Trained service technician.
Table 5. DSA Preboot messages (continued) • Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. • See Chapter 7 “Parts listing, RS210 Types 6531, 6532, 6533, and 6534” on page 175 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU). • If an action step is preceded by “(Trained service technician only),” that step must be performed only by a Trained service technician.
Table 5. DSA Preboot messages (continued) • Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. • See Chapter 7 “Parts listing, RS210 Types 6531, 6532, 6533, and 6534” on page 175 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU). • If an action step is preceded by “(Trained service technician only),” that step must be performed only by a Trained service technician.
Table 5. DSA Preboot messages (continued) • Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. • See Chapter 7 “Parts listing, RS210 Types 6531, 6532, 6533, and 6534” on page 175 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU). • If an action step is preceded by “(Trained service technician only),” that step must be performed only by a Trained service technician.
Table 5. DSA Preboot messages (continued) • Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. • See Chapter 7 “Parts listing, RS210 Types 6531, 6532, 6533, and 6534” on page 175 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU). • If an action step is preceded by “(Trained service technician only),” that step must be performed only by a Trained service technician.
Table 5. DSA Preboot messages (continued) • Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. • See Chapter 7 “Parts listing, RS210 Types 6531, 6532, 6533, and 6534” on page 175 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU). • If an action step is preceded by “(Trained service technician only),” that step must be performed only by a Trained service technician.
Table 5. DSA Preboot messages (continued) • Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. • See Chapter 7 “Parts listing, RS210 Types 6531, 6532, 6533, and 6534” on page 175 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU). • If an action step is preceded by “(Trained service technician only),” that step must be performed only by a Trained service technician.
Table 5. DSA Preboot messages (continued) • Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. • See Chapter 7 “Parts listing, RS210 Types 6531, 6532, 6533, and 6534” on page 175 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU). • If an action step is preceded by “(Trained service technician only),” that step must be performed only by a Trained service technician.
Table 5. DSA Preboot messages (continued) • Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. • See Chapter 7 “Parts listing, RS210 Types 6531, 6532, 6533, and 6534” on page 175 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU). • If an action step is preceded by “(Trained service technician only),” that step must be performed only by a Trained service technician.
Table 5. DSA Preboot messages (continued) • Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. • See Chapter 7 “Parts listing, RS210 Types 6531, 6532, 6533, and 6534” on page 175 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU). • If an action step is preceded by “(Trained service technician only),” that step must be performed only by a Trained service technician.
Table 5. DSA Preboot messages (continued) • Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. • See Chapter 7 “Parts listing, RS210 Types 6531, 6532, 6533, and 6534” on page 175 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU). • If an action step is preceded by “(Trained service technician only),” that step must be performed only by a Trained service technician.
Table 5. DSA Preboot messages (continued) • Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. • See Chapter 7 “Parts listing, RS210 Types 6531, 6532, 6533, and 6534” on page 175 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU). • If an action step is preceded by “(Trained service technician only),” that step must be performed only by a Trained service technician.
Table 5. DSA Preboot messages (continued) • Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. • See Chapter 7 “Parts listing, RS210 Types 6531, 6532, 6533, and 6534” on page 175 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU). • If an action step is preceded by “(Trained service technician only),” that step must be performed only by a Trained service technician.
Table 5. DSA Preboot messages (continued) • Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. • See Chapter 7 “Parts listing, RS210 Types 6531, 6532, 6533, and 6534” on page 175 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU). • If an action step is preceded by “(Trained service technician only),” that step must be performed only by a Trained service technician.
Table 5. DSA Preboot messages (continued) • Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. • See Chapter 7 “Parts listing, RS210 Types 6531, 6532, 6533, and 6534” on page 175 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU). • If an action step is preceded by “(Trained service technician only),” that step must be performed only by a Trained service technician.
Table 5. DSA Preboot messages (continued) • Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. • See Chapter 7 “Parts listing, RS210 Types 6531, 6532, 6533, and 6534” on page 175 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU). • If an action step is preceded by “(Trained service technician only),” that step must be performed only by a Trained service technician.
Table 5. DSA Preboot messages (continued) • Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. • See Chapter 7 “Parts listing, RS210 Types 6531, 6532, 6533, and 6534” on page 175 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU). • If an action step is preceded by “(Trained service technician only),” that step must be performed only by a Trained service technician.
Table 5. DSA Preboot messages (continued) • Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. • See Chapter 7 “Parts listing, RS210 Types 6531, 6532, 6533, and 6534” on page 175 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU). • If an action step is preceded by “(Trained service technician only),” that step must be performed only by a Trained service technician.
Table 5. DSA Preboot messages (continued) • Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. • See Chapter 7 “Parts listing, RS210 Types 6531, 6532, 6533, and 6534” on page 175 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU). • If an action step is preceded by “(Trained service technician only),” that step must be performed only by a Trained service technician.
Table 5. DSA Preboot messages (continued) • Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. • See Chapter 7 “Parts listing, RS210 Types 6531, 6532, 6533, and 6534” on page 175 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU). • If an action step is preceded by “(Trained service technician only),” that step must be performed only by a Trained service technician.
Table 5. DSA Preboot messages (continued) • Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. • See Chapter 7 “Parts listing, RS210 Types 6531, 6532, 6533, and 6534” on page 175 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU). • If an action step is preceded by “(Trained service technician only),” that step must be performed only by a Trained service technician.
Table 5. DSA Preboot messages (continued) • Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. • See Chapter 7 “Parts listing, RS210 Types 6531, 6532, 6533, and 6534” on page 175 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU). • If an action step is preceded by “(Trained service technician only),” that step must be performed only by a Trained service technician.
Table 5. DSA Preboot messages (continued) • Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. • See Chapter 7 “Parts listing, RS210 Types 6531, 6532, 6533, and 6534” on page 175 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU). • If an action step is preceded by “(Trained service technician only),” that step must be performed only by a Trained service technician.
Table 5. DSA Preboot messages (continued) • Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. • See Chapter 7 “Parts listing, RS210 Types 6531, 6532, 6533, and 6534” on page 175 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU). • If an action step is preceded by “(Trained service technician only),” that step must be performed only by a Trained service technician.
Table 5. DSA Preboot messages (continued) • Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. • See Chapter 7 “Parts listing, RS210 Types 6531, 6532, 6533, and 6534” on page 175 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU). • If an action step is preceded by “(Trained service technician only),” that step must be performed only by a Trained service technician.
Table 5. DSA Preboot messages (continued) • Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. • See Chapter 7 “Parts listing, RS210 Types 6531, 6532, 6533, and 6534” on page 175 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU). • If an action step is preceded by “(Trained service technician only),” that step must be performed only by a Trained service technician.
Table 5. DSA Preboot messages (continued) • Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. • See Chapter 7 “Parts listing, RS210 Types 6531, 6532, 6533, and 6534” on page 175 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU). • If an action step is preceded by “(Trained service technician only),” that step must be performed only by a Trained service technician.
Table 5. DSA Preboot messages (continued) • Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. • See Chapter 7 “Parts listing, RS210 Types 6531, 6532, 6533, and 6534” on page 175 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU). • If an action step is preceded by “(Trained service technician only),” that step must be performed only by a Trained service technician.
Table 5. DSA Preboot messages (continued) • Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. • See Chapter 7 “Parts listing, RS210 Types 6531, 6532, 6533, and 6534” on page 175 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU). • If an action step is preceded by “(Trained service technician only),” that step must be performed only by a Trained service technician.
Table 5. DSA Preboot messages (continued) • Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. • See Chapter 7 “Parts listing, RS210 Types 6531, 6532, 6533, and 6534” on page 175 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU). • If an action step is preceded by “(Trained service technician only),” that step must be performed only by a Trained service technician.
Table 5. DSA Preboot messages (continued) • Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. • See Chapter 7 “Parts listing, RS210 Types 6531, 6532, 6533, and 6534” on page 175 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU). • If an action step is preceded by “(Trained service technician only),” that step must be performed only by a Trained service technician.
Table 5. DSA Preboot messages (continued) • Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. • See Chapter 7 “Parts listing, RS210 Types 6531, 6532, 6533, and 6534” on page 175 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU). • If an action step is preceded by “(Trained service technician only),” that step must be performed only by a Trained service technician.
Table 5. DSA Preboot messages (continued) • Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. • See Chapter 7 “Parts listing, RS210 Types 6531, 6532, 6533, and 6534” on page 175 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU). • If an action step is preceded by “(Trained service technician only),” that step must be performed only by a Trained service technician.
Table 5. DSA Preboot messages (continued) • Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. • See Chapter 7 “Parts listing, RS210 Types 6531, 6532, 6533, and 6534” on page 175 to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU). • If an action step is preceded by “(Trained service technician only),” that step must be performed only by a Trained service technician.
• In-band method: Recover server firmware, using either the boot block jumper (Automated Boot Recovery) and a server Firmware Update Package Service Pack. • Out-of-band method: Use the IMM Web Interface to update the firmware, using the latest server firmware update package. Notes: You can obtain a server update package from one of the following sources: • Download the server firmware update from the World Wide Web. • Contact your Lenovo service representative.
Step 7. Boot the server to an operating system that is supported by the firmware update package that you downloaded. Step 8. Perform the firmware update by following the instructions that are in the firmware update package readme file. Step 9. Copy the downloaded firmware update package into a directory. Step 10. From a command line, type filename-s, where filename is the name of the executable file that you downloaded with the firmware update package. Step 11.
Solving power problems Power problems can be difficult to solve. For example, a short circuit can exist anywhere on any of the power distribution buses. Usually, a short circuit will cause the power subsystem to shut down because of an overcurrent condition. To diagnose a power problem, use the following general procedure: Step 1. Turn off the server and disconnect all ac power cords. Step 2. Check the power-fault LEDs on the system board (see “Power problems” on page 58). Step 3.
Solving undetermined problems If the diagnostic tests did not diagnose the failure or if the server is inoperative, use the information in this section. If you suspect that a software problem is causing failures (continuous or intermittent), see “Software problems” on page 60. Damaged data in CMOS memory or damaged server firmware can cause undetermined problems.
00000000 00000000 00000000 00 00000000 00 00 • Machine type and model • Microprocessor or hard disk drive upgrades • Failure symptom – Does the server fail the diagnostic tests? – What occurs? When? Where? – Does the failure occur on a single server or on multiple servers? – Is the failure repeatable? – Has this configuration ever worked? – What changes, if any, were made before the configuration failed? – Is this the original reported failure? • Diagnostic program type and version level • Hardware c
106 Hardware Maintenance Manual
Chapter 5. Locating Server Controls and connectors This section describes the controls, light-emitting diodes (LEDs), and connectors on the front and rear of the server, and how to turn the server on and off. For the location of the LEDs on the system board, see “System-board LEDs” on page 112. Note: The illustrations in this document might differ slightly from your model.
Rear view 1 Power-cord connector 9 NMI button 2 Serial connector 10 USB 3-4 connector 3 Ethernet 1 activity LED 11 USB 1-2 connector 4 Ethernet 1 link LED 12 Video connector 5 Ethernet 2 activity LED 13 Power supply error LED (amber) 6 Ethernet 2 link LED 14 DC power LED (green) 7 PCI slot 1 15 AC power LED (green) 8 PCI slot 2 System-board internal connectors DIMMs DIMMs Heatsink Orientation Microprocessor The following illustration shows the internal connectors on the s
3 DIMM 3 13 Operator information panel connector 23 Battery 4 DIMM 4 14 Simple-swap HDD backplane signal connector 24 Power 2 connector 5 DIMM 5 15 Wake-on-LAN connector 25 Virtual media key connector 6 DIMM 6 16 DVD drive connector 26 Power 1 connector 7 Microprocessor 17 Hypervisor flash device connector 27 Power 3 connector Power 4 connector 8 Fan 3 connector 18 Reserved 28 9 Fan 2 connector 19 Reserved 29 Fan 5 connector 10 ServeRAD-BR10il controller connector
DIMMs DIMMs Heatsink Orientation Microprocessor 1 DIMM 1 8 DVD drive connector 2 DIMM 2 9 Hypervisor flash device connector Riser-card connector 2 3 DIMM 3 10 4 DIMM 4 11 Riser-card connector 1 5 DIMM 5 12 Battery 6 DIMM 6 13 Virtual media key connector 7 ServeRAID BR10il SAS/SATA controller connector The following illustration shows the locations of the PCI Express slots on the riser-card assembly.
1 2 PCI-X power cable PCI-X slot System-board switches and jumpers DIMMs DIMMs Heatsink Orientation Microprocessor The following illustration shows the switches and jumpers on the system board. The following table describes the jumpers on the system board. Table 6. System board jumpers Jumper number Jumper name Jumper setting JP1 Clear CMOS jumper 1 • Pins 1 and 2: Keep CMOS data (default).
Table 6. System board jumpers (continued) Jumper number Jumper name Jumper setting Notes: 1. If no jumper is present, the server responds as if the pins are set to 1 and 2. 2. Changing the position of the UEFI boot recovery jumper from pins 1 and 2 to pins 2 and 3 before the server is turned on alters which flash ROM page is loaded. Do not change the jumper pin position after the server is turned on. This can cause an unpredictable problem. Important: 1.
7 SAS/SATA Controller LED 8 IMM heart beat LED 15 DIMM 1-6 error LEDs Table 7. System-board LEDs LED Description Error LEDs When one of these LEDs is lit, it indicates that the associated component has failed. Baseboard management controller heartbeat LED This LED flashes to indicate that the IMM is functioning normally. Standby power LED When this LED is lit, it indicates that the server is connected to ac power.
CAUTION: The power control button on the device and the power switch on the power supply do not turn off the electrical current supplied to the device. The device also might have more than one power cord. To remove all electrical current from the device, ensure that all power cords are disconnected from the power source. 2 1 The server can be turned off in any of the following ways: • You can turn off the server from the operating system, if your operating system supports this feature.
Chapter 6. Replacing FRUs This chapter provides detailed instructions for replacing FRUs in the server. Guidelines for trained service technicians This section contains information for trained service technicians. Inspecting for unsafe conditions Use the information in this section to help you identify potential unsafe conditions in a Lenovo product that you are working on.
• Check the area for electrical hazards such as moist floors, nongrounded power extension cords, power surges, and missing safety grounds. • Use only approved tools and test equipment. Some hand tools have handles that are covered with a soft material that does not provide insulation from live electrical currents. • Regularly inspect and maintain your electrical hand tools for safe operational condition. Do not use worn or broken tools or testers.
• Remove jewelry, such as bracelets, necklaces, rings, and loose-fitting wrist watches. • Remove items from your shirt pocket, such as pens and pencils, that could fall into the server as you lean over it. • Avoid dropping any metallic objects, such as paper clips, hairpins, and screws, into the server. Handling static-sensitive devices Attention: Static electricity can damage the server and other electronic devices.
000000 000000 000 000000 000 000 1 Riser card assembly 12 Bezel 2 DIMM air baffle 13 DVD drive filler 3 DIMM 14 Operator information panel 4 Power supply 15 Fans 5 SAS/SATA backplane (some models) 16 System board 6 SATA simple-swap back panel (some models) 17 Microprocessor 7 3.5-inch drive cage 18 Heat sink 8 3.
10 Hot-swap hard disk drive filler 11 3.5-inch or 2.5-inch hot-swap hard disk drive (depending on model) Removing and installing the cover Use the following procedures to remove and install the cover: Removing the cover To remove the server cover, do the following: 1. Read the safety information in “Important Safety Information” on page 1 and “Guidelines for trained service technicians” on page 115. 2.
00000000 00000000 00000000 00000000 00000000 Removing and installing the bezel To remove the bezel, complete the following steps: 1. Remove the server from the rack and remove the cover (see “Removing and installing the cover” on page 119). 2. From inside the server, press the bezel release latch 1 toward the left side of the server. 3. Pivot the bezel 2 forward and pull it away from the server.
Attention: For proper cooling and airflow, replace the bezel and server cover before you turn on the server. To install the bezel, insert the tab at the right end of the bezel into the front of the chassis and pivot the bezel until it snaps into place. Attention: For proper cooling and airflow, replace the server cover before you turn on the server. Removing and installing the DIMM air baffle The DIMM air baffle must be removed to allow access to some of the server components.
Replacing a memory module (DIMM) To replace a dual inline memory module (DIMM), use the following information and procedures: Supported memory types Following is information that describes the types of dual inline memory modules (DIMMs) that the server supports and other information that you must consider when you install DIMMs (see “System-board internal connectors” on page 108 for the location of the DIMM connectors).
Note: To determine the type of a DIMM, see the label on the DIMM. The information on the label is in the format xxxxx nRxxx PC3-xxxxx-xx-xx-xxx. The numeral in the sixth numerical position indicates whether the DIMM is single-rank (n=1) or dual-rank (n=2). • The server supports up to two UDIMMs or three RDIMMs per channel. The following table shows an example of the maximum amount of memory that you can install, using ranked DIMMs.
• The memory channels run at the fastest common frequency of the installed DIMMs. • RDIMMs are supported in models with an Xeon 3400 series processor. • Do not use both RDIMMs and UDIMMs in the same server. • The server supports up to three single-rank, dual-rank, or quad-rank RDIMMs per channel. • The RDIMM options that are available for the server are 1 GB, 2 GB, 4 GB, and 8 GB (when available) DIMMs. • You can install a maximum of 32 GB of memory in the server when you use RDIMMs.
Note: The amount of usable memory is reduced, depending on the system configuration. A certain amount of memory must be reserved for system resources. To view the total amount of installed memory and the amount of configured memory, run the Setup utility. Removing a memory module To remove a DIMM, complete the following steps: 1. Read the safety information in “Important Safety Information” on page 1 and “Guidelines for trained service technicians” on page 115. 2.
To install a DIMM, complete the following steps: 1. Read the safety information in “Important Safety Information” on page 1 and “Guidelines for trained service technicians” on page 115. 2. Turn off the server and peripheral devices and disconnect the power cords and all external cables, if necessary. 3. Remove the cover (see “Removing and installing the cover” on page 119). 4. Remove the DIMM air baffle (see “Removing and installing the DIMM air baffle” on page 121). 5.
Note: If a RAID controller or PCI card is installed, you might have to reconfigure the disk arrays after you install or remove hard disk drives. See the documentation that comes with the PCI card for more information. Removing a simple-swap Serial ATA (SATA) hard disk drive Attention: Simple-swap hard disk drives are not hot-swappable. Disconnect all power from the server before you remove or install a simple-swap hard disk drive.
000000000 000000000 000000000 000000000 000000000 000000000 000 000 000 00000 00000 00000 6. Release the loops of the drive tray. 7. Insert the filler panel into the bay to cover the drive. Note: If the server is configured for RAID operation using a RAID controller, you might have to reconfigure your disk arrays after you install hard disk drives. See the RAID controller documentation for additional information about RAID operation and complete instructions for using the RAID controller. 8.
000000000 000000000 000000000 000000000 000000000 000000000 3. Grasp the handle and pull the hot-swap drive assembly 2 out of the drive bay. Installing a hot-swap hard disk drive To install a hot-swap hard disk drive, complete the following steps. Note: If your server has only one hot-swap hard disk drive, install it in the left or upper-left drive bay.
000000000 000000000 000000000 000000000 000000000 000000000 c. Gently push the drive assembly into the bay until the drive stops. d. Push the tray handle 2 to the closed (locked) position. e. Check the hard disk drive status LED to make sure that the hard disk drive is operating correctly. If the amber hard disk drive status LED for a drive is lit continuously, that drive is faulty and must be replaced. If the green hard disk drive activity LED is flashing, the drive is being accessed.
1 PCI-X power cable 2 PCI-X slot 7. Grasp the riser-card assembly at the front grip point and rear edges and lift to remove it from the server. 8. Place the riser-card assembly on a flat, static-protective surface. 9. Carefully grasp the PCI card by its top edge or upper corners, and pull the PCI card from the riser-card assembly.
Installing a PCI card To install a PCI card, complete the following steps: 1. Read the safety information in “Important Safety Information” on page 1 and “Guidelines for trained service technicians” on page 115. 2. Turn off the server and peripheral devices and disconnect the power cords and all external cables; then, remove the server cover (see “Removing and installing the cover” on page 119). 3.
Attention: PCI expansion-slot covers must be installed on all vacant slots. This maintains the electronic emissions characteristics of the server and ensures proper cooling of server components. 6. Follow the instructions that come with the PCI card to set any jumpers or switches. Attention: When you install an PCI card, make sure that it is completely and correctly seated in the expansion slot in the riser card.
Removing a USB embedded hypervisor flash device To remove a hypervisor flash device, complete the following steps: 1. Read the safety information in “Important Safety Information” on page 1 and “Guidelines for trained service technicians” on page 115. 2. Turn off the server and peripheral devices and disconnect the power cords. 3. Remove the cover (see “Removing and installing the cover” on page 119). 4. Remove the riser-card assembly (see “Removing the riser-card assembly” on page 156). 5.
6. Lift the operator information panel assembly out of the server. 7. If you are instructed to return the operator information panel assembly, follow all packaging instructions, and use any packaging materials for shipping that are supplied to you. Installing the operator information panel assembly To install the replacement operator information panel assembly, complete the following steps: 1. Guide the operator information panel assembly into position on top of the DVD bay housing.
Replacing the drive cage To replace the drive cage, use the following procedures: Removing the drive cage The following illustration shows removing a simple-swap 3.5-inch drive cage. 0000 0000 0000 0000 0000 0000 The following illustration shows removing a hot-swap 3.5-inch drive cage. The following illustration shows removing a hot-swap 2.5-inch drive cage.
To remove a drive cage, complete the following steps: 1. Read the safety information in “Important Safety Information” on page 1 and “Guidelines for trained service technicians” on page 115. 2. Turn off the server and peripheral devices, and disconnect the power cord and all external cables. 3. Remove the hard disk drives from the cage (see “Replacing hard disk drives” on page 126. 4. Remove the cover (see “Removing and installing the cover” on page 119).
0000 0000 0000 0000 0000 0000 The following illustration shows installing a hot-swap 3.5-inch drive cage. The following illustration shows installing a hot-swap 2.5-inch drive cage.
To install a drive cage, complete the following steps: 1. Make sure that the backplane or back plate is removed from the drive cage. (See “Removing the backplane or back plate (3.5-inch drives)” on page 153 or “Removing the SAS backplane (2.5-inch drives)” on page 155 for instructions, as applicable.) 2. Line up the drive cage with the drive bays on the front of the server. 3. Push the drive cage into the server until it stops. 4.
4. Remove the DIMM air baffle (see “Removing and installing the DIMM air baffle” on page 121). 5. Remove the heat sink. CAUTION: The heat sink may become very hot during normal operation. Allow time for the heat sink to cool down before you touch it. a. Loosen the screw on one side of the heat sink to break the seal with the microprocessor. b. Press firmly on the captive screws and loosen them with a screwdriver. c. Use your fingers to gently pull the heat sink from the microprocessor. 6.
10. If you are instructed to return the microprocessor, follow all packaging instructions, and use any packaging materials for shipping that are supplied to you. Installing the microprocessor The following notes describe the type of microprocessor that the server supports and other information that you must consider when you install a microprocessor and heat sink: • If you have to replace a microprocessor, call for service.
Attention: Do not touch the thermal material on the bottom of the heat sink. Touching the thermal material will contaminate it. If the thermal material on the microprocessor or heat sink becomes contaminated, contact your service technician. a. Make sure that the thermal material is still on the bottom of the heat sink; then, align the heat sink so that the arrows on the label point toward the DIMMs and place the heat sink on top of the microprocessor, thermal material side down. b.
Notes: 1. Read the safety information at “Important Safety Information” on page 1. 2. Read “Guidelines for trained service technicians” on page 115. 3. Read “Handling static-sensitive devices” on page 117. To replace damaged or contaminated thermal grease on the microprocessor and heat sink, complete the following steps: 1. Place the heat sink on a clean work surface. 2. Remove the cleaning pad from its package and unfold it completely. 3.
3. Turn off the peripheral devices and disconnect all power cords; then, remove the cover (see “Removing and installing the cover” on page 119). Note: When you replace the system board, you must either update the server with the latest firmware or restore the pre-existing firmware that the customer provides on a diskette or CD image. Make sure that you have the latest firmware or a copy of the pre-existing firmware before you proceed. 4.
Installing the system board Note: When you reassemble the components in the server, be sure to route all cables carefully so that they are not exposed to excessive pressure. Notes: 1. When you reassemble the components in the server, be sure to route all cables carefully so that they are not exposed to excessive pressure. 2. When you replace the system board, you must either update the server with the latest firmware or restore the pre-existing firmware that the customer provides on a diskette or CD image.
Statement 5 CAUTION: The power control button on the device and the power switch on the power supply do not turn off the electrical current supplied to the device. The device also might have more than one power cord. To remove all electrical current from the device, ensure that all power cords are disconnected from the power source. 2 1 Statement 8 CAUTION: Never remove the cover on a power supply or any part that has the following label attached.
6. Remove the screw 2 that holds the power supply 1 to the rear of the chassis. 00000000 00000000 00000000 00 00000000 00 00 7. Loosen the captive thumbscrew 3 that secures the power supply to the chassis bottom. 8. Lift the power supply out of the bay. 9. If you are instructed to return the power supply, follow all packaging instructions, and use any packaging materials for shipping that are supplied to you.
8. Turn off the server and disconnect the ac power cord. 9. Connect the cables from the power supply to the internal devices. 10. Install the DIMM air baffle (see “Removing and installing the DIMM air baffle” on page 121). 11. Install the cover (see “Removing and installing the cover” on page 119). 12. Slide the server into the rack. 13. Reconnect the ac power cord into the connector on the back of the power supply. 14. Reconnect all external cables that were disconnected. 15.
Table 14. Removing the fan 1 Fan 1 4 Fan 4 2 Fan 2 5 Fan 5 3 Fan 3 9. If you are instructed to return the fan, follow all packaging instructions, and use any packaging materials for shipping that are supplied to you. Installing a fan assembly To install the replacement fan, complete the following steps: 1. Position the replacement fan so that the airflow arrow on the fan points toward the rear of the server. Note: Correct airflow is from the front to the rear of the server. 2.
b. In the location from which you removed the failed fan, route the fan cable into its slot 2 in the fan bracket top. c. Insert the fan 4 into the bracket 3 . d. Make sure that each of the grey soft tabs on the fan is fully seated in its slot in the fan bracket. 3. Connect the replacement fan cable to the system board. 4. Go to “Completing the FRU replacement” on page 172.
DIMMs DIMMs Heatsink Orientation Microprocessor a. Use a fingernail to press the top of the battery clip away from the battery. The battery pops up when released. b. Use your thumb and index finger to lift the battery from the socket. 6. Dispose of the battery as required by local ordinances or regulations. See “Battery return program” on page 225 for more information.
manufacturer. If your system has a module containing a lithium battery, replace it only with the same module type made by the same manufacturer. The battery contains lithium and can explode if not properly used, handled, or disposed of. Do not: • Throw or immerse into water • Heat to more than 100°C (212°F) • Repair or disassemble Dispose of the battery as required by local ordinances or regulations. To install the replacement battery, complete the following steps: 1.
Replacing the SAS/SATA hard disk drive back plate or backplane To replace the SAS/SATA hard disk drive backplane or back plate, complete the following procedures: Removing the backplane or back plate (3.5-inch drives) To remove the Serial Attached SCSI (SAS) backplane, which is also referred to as the hot-swap SAS/SATA backplane, or to remove the simple-swap SATA back plate, complete the following steps. 1.
00000000 00000000 00000000 00 00000000 00 00 1 Connectors 2 Guide channels 1. Connect the power cable to the replacement backplane or back plate. 2. Reconnect the backplane or back plate cables: • If the server is a hot-swap model, reconnect the SAS/SATA controller signal cable to the backplane. • If the server is a simple-swap model that contains a standard SATA back plate, reconnect the SATA cable to the system board.
Removing the SAS backplane (2.5-inch drives) 1 Alignment tabs 3 Alignment slots 2 Connectors 4 Connectors To remove the 2.5-inch drives backplane, complete the following steps: 1. Read the safety information in “Important Safety Information” on page 1 and “Guidelines for trained service technicians” on page 115. 2. Turn off the server and peripheral devices, and disconnect the power cords and all external cables. 3. Remove the server from the rack and place it on a flat, static-protective surface.
1 Alignment tabs 3 Alignment slots 2 Drive connectors 4 Drive connectors 1. Connect the cables to the replacement backplane. 2. Slide the backplane into the card guides, making sure that any nearby wires or cables are not trapped or pinched. 3. Press firmly until the backplane is fully seated and clicks into place. 4. Install the hard disk drives. 5. Go to “Completing the FRU replacement” on page 172.
00000000 00000000 00000000 00 00000000 00 00 6. If the riser-card assembly is an optional PCI-X riser-card assembly, disconnect the riser-card power cable 1 from the riser-card assembly. 7. Disconnect any cables from the PCI cards in the riser-card assembly. 8. If you are instructed to return the riser-card assembly, follow all packaging instructions, and use any packaging materials for shipping that are supplied to you.
5. Carefully align the riser-card assembly with the guides on the rear of the server and with the riser-card connectors on the system board; then, press down on the assembly. Make sure that the riser-card assembly 1 is fully seated in the connector on the system board. 00000000 00000000 00000000 00 00000000 00 00 6. Go to “Completing the FRU replacement” on page 172.
6. Disconnect the signal cables that are attached to the SAS/SATA controller. 7. Grasp the SAS/SATA controller 1 while you press outward on the plastic tabs. 8. Pull out the SAS/SATA controller from the connector 2 on the system board. 9. If you are instructed to return the SAS/SATA controller, follow all packaging instructions, and use any packaging materials for shipping that are supplied to you.
6. Touch the static-protective package that contains the new ServeRAID-BR10il SAS/SATA controller to any unpainted surface on the outside of the server; then, grasp the controller by the top edge or upper corners of the controller and remove it from the package. 7. Align the ServeRAID controller 1 so that the keys align correctly with the connector 2 on the system board. 8. Insert the ServeRAID controller into the connector on the system board until it is firmly seated.
10. Connect the signal cable that is attached to the drive backplane 1 to the ServeRAID controller connector 2. 11. Replace the riser-card assembly (see “Installing the riser-card assembly” on page 157). Note: When you restart the server, you are prompted to import the existing RAID configuration to the new ServeRAID controller. 12. Go to “Completing the FRU replacement” on page 172.
3. Align the cable connector with the connector on the rear of the DVD drive cage and press the cable connector into the DVD drive cage connector until it is firmly seated. 4. Pull the cable connector latch 2 up and hold it there while you slide the cable connector to the lock position; then, slide the cable connector latch down to lock the cable in place. The following illustration shows cable routing for the DVD drive cable.
5. Connect the DVD drive cable to the system board connector 1 . 6. Reconnect the DVD drive power cable to the power supply cable. 7. Reinstall the DVD drive (see “Replacing a DVD drive” on page 163). 8. Reinstall the riser-card assembly (see “Installing the riser-card assembly” on page 157). 9. Go to “Completing the FRU replacement” on page 172. Replacing a DVD drive To replace a DVD drive, complete the following procedures: Removing a DVD drive To remove a DVD drive, complete the following steps: 1.
6. If you are instructed to return the DVD drive, follow all packaging instructions, and use any packaging materials for shipping that are supplied to you. Installing a DVD drive The following notes describe the type of drives that the server supports and other information that you must consider when you install a DVD drive. • Locate the documentation that comes with the drive and follow those instructions in addition to the instructions in this chapter.
CAUTION: When laser products (such as CD-ROMs, DVD drives, fiber optic devices, or transmitters) are installed, note the following: • Do not remove the covers. Removing the covers of the laser product could result in exposure to hazardous laser radiation. There are no serviceable parts inside the device. • Use of controls or adjustments or performance of procedures other than those specified herein might result in hazardous radiation exposure.
Microprocessor Heatsink Orientation DIMMs DIMMs 4. If you are instructed to return the virtual media key, follow all packaging instructions, and use any packaging materials for shipping that are supplied to you. Installing the virtual media key To install the virtual media key, complete the following steps: 1. Read the safety information in “Important Safety Information” on page 1 and “Guidelines for trained service technicians” on page 115. 2.
Microprocessor Heatsink Orientation DIMMs DIMMs 4. Go to “Completing the FRU replacement” on page 172. Replacing the PCI-X riser-card power cable To replace the PCI-X riser-card power cable, use the following procedures: Removing the PCI-X riser-card power cable If an optional PCI-X riser-card assembly is installed in the server, an internal power cable for the assembly is also installed. To remove the PCI-X riser-card power cable, complete the following steps: 1.
7. Disconnect the riser-card power cable from the PCI-X riser card. 8. If you are instructed to return the PCI-X riser-card power cable, follow all packaging instructions, and use any packaging materials for shipping that are supplied to you. Installing the PCI-X riser-card power cable To install the replacement PCI-X riser-card power cable, complete the following steps. 1. Connect the riser-card power cable to the PCI-X riser-card assembly. 2.
3. Copy and unpack the ASU package, which also includes other required files, to the server. Make sure that you unpack the ASU and the required files to the same directory. In addition to the application executable (asu or asu64), the following files are required: • For Windows based operating systems: – ibm_rndis_server_os.inf – device.cat • For Linux based operating systems: – cdc_interface.sh 4. After you install ASU, use the following command syntax to set the UUID: asu set SYSTEM_PROD_DATA.
c. From Family list, select ThinkServer RS210;, and click Continue. d. Click Downloads and drivers. e. Click User's guides and manuals to link to the ASU Users Guide. • Remote LAN access, type the command: Note: When using the remote LAN access method to access IMM using the LAN from a client, the host and the imm_external_ip address are required parameters. host [user [[password ] Where: imm_external_ip The external IMM LAN IP address.
– device.cat • For Linux based operating systems: – cdc_interface.sh 4. After you install ASU, Type the following commands to set the DMI: asu set SYSTEM_PROD_DATA.SysInfoProdName [access_method]asu set SYSTEM_PROD_DATA.SysInfoSerialNum [access_method]asu set SYSTEM_PROD_DATA.SysEncloseAssetTag [access_method] Where: The server machine type and model number. Type mtm xxxxyy, where xxxx is the machine type and yyy is the server model number.
corresponding mapping layer. To see the Advanced Settings Utility Users Guide. You can access the ASU Users Guide from the Lenovo support Web site. a. Go to http://www.lenovo.com/support. b. Enter your product number (machine type and model number) or select Servers and Storage from the Select your product list. c. From Family list, select ThinkServer RS210;, and click Continue. d. Click Downloads and drivers. e. Click User's guides and manuals to link to the ASU Users Guide.
5. Update the server configuration (see “Updating the server configuration” on page 174). 6. Slide the server back into the rack, if necessary. 7. Turn on the peripheral devices and the server. Connecting the cables The following illustration shows the locations of the input and output connectors on the front of the server.
Updating the server configuration When you start the server for the first time after you add or remove an internal option or external device, you might receive a message that the configuration has changed. The UEFI Setup Utility program starts automatically so that you can save the new configuration settings. Some options have device drivers that you must install. For information about installing device drivers, see the documentation that comes with each option.
Chapter 7. Parts listing, RS210 Types 6531, 6532, 6533, and 6534 The following replaceable components are available for the ThinkServer RS210 Types 6531, 6532, 6533, and 6534 servers. To check for an updated parts listing on the Web, complete the following steps: 1. Go to http://www.lenovo.com/support. 2. Enter your product number (machine type and model number) or select Servers and Storage from the Select your product list. 3. From Family list, select ThinkServer RS210, and click Continue.
1 Riser card assembly 12 Bezel 2 DIMM air baffle 13 DVD drive filler 3 DIMM 14 Operator information panel 4 Power supply 15 Fans 5 SAS/SATA backplane (some models) 16 System board 6 SATA simple-swap back panel (some models) 17 Microprocessor 7 3.5-inch drive cage 18 Heat sink 8 3.5-inch simple-swap SATA hard disk drive (some models) 19 Cover 9 Simple-swap SATA filler 10 Hot-swap hard disk drive filler 11 3.5-inch or 2.
Table 15.
Table 15. Parts listing, Types 6531 (continued) Index Description CRU part number (Tier 1) CRU part number (Tier 2) FRU part number 11 IBM 146GB 15K 6Gbps SAS 2.5" SFF Slim-HS HDD (models CTO 12U 12F 12S 12L 12D 12Y 12G 12M 12A 12J) 46U2117 11 IBM 500GB 7200 6Gbps NL SAS 2.5" SFF Slim-HS HDD (models CTO 12U 12F 12S 12L 12D 12Y 12G 12M 12A 12J) 46U2758 11 ThinkServer 300GB 6Gbps 15K 3.5’ Hot-Swap SAS drive (models CTO All Models) 46U3014 11 ThinkServer 450GB 6Gbps 15K 3.
Table 15. Parts listing, Types 6531 (continued) Index Description CRU part number (Tier 1) Cable, 3.5" SS SATA Cable (models CTO All Models) 59Y3230 Blank EMC Shield (models CTO All Models) 44T2248 Fornt I/O Board (models CTO All Models) 46C6797 HD InstCaution Label (models CTO All Models) 59Y3218 Low case (models CTO All Models) 59Y3225 2.
6531 Software FRU FRU# WS2008 R2 FOUND 64bit GR (models CTO All Models) 90Y1169 WS2008 R2 FOUND 64bit IT (models CTO All Models) 90Y1170 WS2008 R2 FOUND 64bit JP (models CTO All Models) 90Y1171 WS2008 R2 FOUND 64bit SP (models CTO All Models) 90Y1172 WS2008 R2 FOUND 64bit TR (models CTO All Models) 90Y1173 WS 2008 SBS SP2 STD 64bit US (models CTO All Models) 90Y1174 WS 2008 SBS SP2 STD 64bit NL (models CTO All Models) 90Y1175 WS 2008 SBS SP2 STD 64bit FR (models CTO All Models) 90Y1176 WS
Table 16.
Table 16. Parts listing, Types 6532 (continued) Index Description CRU part number (Tier 1) CRU part number (Tier 2) FRU part number 11 Hard disk drive, 750GB 7200 RPM 3.5" Hot-Swap SATA II (models CTO 11U 11F 11S 11L 11D 11Y 11G 11M 11A 11J) 45J9646 11 Hard disk drive, IBM 1TB 7200 SATA 3.5'' HS HDD (models CTO 11U 11F 11S 11L 11D 11Y 11G 11M 11A 11J) 45J9648 11 IBM 146GB 10K 6Gbps SAS 2.
Table 16.
Table 16.
6532 Software FRU FRU# WS 2008 R2 ENT 64bit JP (models CTO All Models) 90Y1196 WS 2008 R2 ENT 64bit SP (models CTO All Models) 90Y1197 WS 2008 R2 ENT 64bit TR (models CTO All Models) 90Y1198 ROK WS2008 FOUND 64bit MUI EN/JP (models CTO All Models) 90Y1199 ROK WS2008 FOUND 64bit MUI EN/FR/GR/SP/IT (models CTO All Models) 90Y1200 Table 17.
Table 17. Parts listing, Types 6533 (continued) Index Description CRU part number (Tier 1) CRU part number (Tier 2) FRU part number 8 Hard disk drive, 250GB 7200 RPM 3.5" Simple-Swap SATA II (models CTO 11G 11M 11A 11J) 45J9634 8 Hard disk drive, 500GB 7200 RPM 3.5" Simple-Swap SATA II (models CTO 11G 11M 11A 11J ) 46U1024 8 Hard disk drive, 750GB 7200 RPM 3.5" Simple-Swap SATA II (models CTO 11G 11M 11A 11J ) 45J9638 8 Hard disk drive, IBM Server 1TB 7200 SATA 3.
Table 17. Parts listing, Types 6533 (continued) Index Description CRU part number (Tier 1) Cable, 3.5" SS SATA cable (models CTO All Models) 59Y3230 Blank EMC shield (models CTO All Models) 44T2248 Fornt I/O board (models CTO All Models) 46C6797 HD InstCaution Label (models CTO All Models) 59Y3218 Low case (models CTO All Models) 59Y3225 2.
6533 Software FRU FRU# WS2008 R2 FOUND 64bit IT (models CTO All Models) 90Y1170 WS2008 R2 FOUND 64bit JP (models CTO All Models) 90Y1171 WS2008 R2 FOUND 64bit SP (models CTO All Models) 90Y1172 WS2008 R2 FOUND 64bit TR (models CTO All Models) 90Y1173 WS 2008 SBS SP2 STD 64bit US (models CTO All Models) 90Y1174 WS 2008 SBS SP2 STD 64bit NL (models CTO All Models) 90Y1175 WS 2008 SBS SP2 STD 64bit FR (models CTO All Models) 90Y1176 WS 2008 SBS SP2 STD 64bit GR (models CTO All Models) 90Y1177
Table 18.
Table 18. Parts listing, Types 6534 (continued) Index Description CRU part number (Tier 1) CRU part number (Tier 2) FRU part number 11 Hard disk drive, 146GB 15K 3.5" Hot-Swap SAS (models CTO 11U 11F 11S 11L 11D 11Y 11G 11M 11A 11J 12U 12F 12S 12L 12D 12Y 12G 12M 12A 12J ) 45J9658 11 Hard disk drive, 750GB 7200 RPM 3.5" Hot-Swap SATA II (models CTO 11U 11F 11S 11L 11D 11Y 11G 11M 11A 11J 12U 12F 12S 12L 12D 12Y 12G 12M 12A 12J ) 45J9646 11 Hard disk drive, IBM 1TB 7200 SATA 3.
Table 18. Parts listing, Types 6534 (continued) Index CRU part number (Tier 1) Description CRU part number (Tier 2) FRU part number 17 Microprocessor, Xeon X3450 2.67GHz/1333MHz-8MB 4C (models CTO 12U 12F 12S 12L 12D 12Y 12G 12M 12A 12J 13U 13F 13S 13L 13D 13Y 13G 13M 13A 13J 14U 14F 14S 14L 14D 14Y 14G 14M 14A 14J) 49Y4649 17 Microprocessor, Pentium G6950 2.8 GHz/1066MHz-3MB 2C (models CTO) 49Y4668 17 Microprocessor, Xeon X3470 2.
Table 18.
6534 Software FRU FRU# WS 2008 R2 STD 64bit US (models CTO All Models) 90Y1183 WS 2008 R2 STD 64bit FR (models CTO All Models) 90Y1184 WS 2008 R2 STD 64bit GR (models CTO All Models) 90Y1185 WS 2008 R2 STD 64bit JP (models CTO All Models) 90Y1186 WS 2008 R2 STD 64bit SP (models CTO All Models) 90Y1187 WS 2008 R2 STD 64bit IT (models CTO All Models) 90Y1188 WS 2008 R2 STD 64bit TR (models CTO All Models) 90Y1189 WS 2008 R2 STD 64bit NL (models CTO All Models) 90Y1190 WS 2008 R2 ENT 64bit US
Table 19. Power cords, Type 6531 Lenovo Power cord part number Used in these countries and regions 39M5247 Taiwan 2.8M (models CTO) 39M5102 ANZ 2.8M (models CTO 11M 12M) 39M5123 Europe 2.8M (models CTO) 39M5130 Denmark 2.8M (models CTO 11G 12G) 39M5144 S. Africa 2.8M (models CTO 11G 11M 11A 12G 12M 12A) 39M5151 UK 2.8M (models CTO 11G 11A 12G 12A) 39M5158 Switzerland 2.8M (models CTO 11G 12G) 39M5165 Italy 2.8M (models CTO 11S 11L 11Y 11G 12S 12L 12Y 12G) 39M5172 Israel 2.
Table 21. Power cords, Type 6533 Lenovo Power cord part number Used in these countries and regions 39M5247 Taiwan 2.8M (models CTO) 39M5102 ANZ 2.8M (models CTO 11M) 39M5123 Europe 2.8M (models CTO) 39M5130 Denmark 2.8M (models CTO 11G) 39M5144 S. Africa 2.8M (models CTO 11G 11M 11A) 39M5151 UK 2.8M (models CTO 11G 11A) 39M5158 Switzerland 2.8M (models CTO 11G) 39M5165 Italy 2.8M (models CTO 11G) 39M5172 Israel 2.8M (models CTO 11G) 39M5219 Korea 2.8M (models CTO) 39M5199 Japan 2.
Table 22. Power cords, Type 6534 (continued) Lenovo Power cord part number Used in these countries and regions 39M5233 Brazil 2.8M (models CTO) 39M5206 China 2.
Chapter 8. Configuring the server The following configuration programs come with the server: • Setup Utility program The Setup Utility program is part of the UEFI. Use it to configure serial port assignments, change interrupt request (IRQ) settings, change the startup-device sequence, set the date and time, and set passwords. • Boot Manager program The Boot Manager program is part of the server firmware.
• Set and change passwords • View and change the startup characteristics of the server and the order of startup devices (startup-drive sequence) • View and change settings for advanced hardware features • View and clear the event and error logs • Change interrupt request (IRQ) settings • Resolve configuration conflicts Starting the Setup Utility To start the Setup Utility, do the following: Step 1. Turn on the server.
Ethernet MAC addresses. If you disable a device, it cannot be configured, and the operating system will not be able to detect it (this is equivalent to disconnecting the device). – Power Select this choice to view or change power capping to control consumption, processors, and performance states. – Legacy Support Select this choice to view or set legacy support. – Force Legacy Video on Boot Select this choice to force INT video support, if the operating system does not support UEFI video output standards.
This choice is on the full Setup Utility menu only. • Start Options Select this choice to view or change the start options, including the startup sequence, keyboard NumLock state, PXE boot option, and PCI device boot priority. Changes in the startup options take effect when you start the server. The startup sequence specifies the order in which the server checks devices to find a boot record. The server starts from the first boot record that it finds.
• Load Default Settings Select this choice to cancel the changes that you have made in the settings and restore the factory settings. • Exit Setup Select this choice to exit from the Setup Utility. If you have not saved the changes that you have made in the settings, you are asked whether you want to save the changes or exit without saving them. Passwords From the System Security choice, you can set, change, and delete a power-on password and an administrator password.
If you forget the administrator password, you can reset it after you change the position of the clear CMOS jumper. Resetting passwords DIMMs DIMMs Heatsink Orientation Microprocessor If you forget the power-on password or administrator password, you can move the clear-CMOS jumper block on the system board to pins 2 and 3, to clear CMOS memory and bypass the power-on or administrator password check. The jumper location is shown in the following illustration. Table 23.
To use the Boot Manager program, do the following: Step 1. Turn off the server. Step 2. Restart the server. Step 3. When the prompt Select Boot Device is displayed, press F12. If a bootable USB mass storage device is installed, a submenu item (USB Key/Disk) is displayed. Step 4. Use the Up arrow and Down arrow keys to select an item from the Boot Selection Menu and press Enter. The server attempts to boot from the selected device.
Table 24. RAID configuration utilities (continued) RAID configuration utility Description Location LSI Configuration Utility For: In system firmware. To access: • IBM ServeRAID-BR10il SAS/SATA Controller • IBM ServeRAID-MR10i SAS/SATA Controller • Use UEFI Setup Utility. Where to find more information “Using LSI Configuration Utility program” on page 204 • Press Ctrl + C at the LSI prompt during startup.
Note: Approximately 1 to 3 minutes after the server is connected to ac power, the power-control button becomes active. 2. When the prompt is displayed, press F1. If you have set an administrator password, you are prompted to type the password. 3. Select System Settings ® Adapters and UEFI drivers. 4. Select Please refresh this page on the first visit and press Enter. 5.
Starting the WebBIOS utility Perform the following steps to start the WebBIOS utility and access the main menu: 1. After you turn on the power and when the computer is starting, you are prompted to press Ctrl + H when the following message is displayed: Copyright© LSI Logic Corporation Press for WebBIOS 2. Select a controller from the list. 3. Click Start. The main WebBIOS utility interface is displayed.
Attention: If you select Clear Configuration or New Configuration, all existing data in the configuration is deleted. Make a backup copy of any data that you want to keep before selecting these options. Clear Configuration Clears the existing configuration. New Configuration Clears the existing configuration and lets you create a new configuration. Add Configuration Retains the existing storage configuration and adds new drives to it (this does not cause any data loss). 3. Click Next. 4.
If you did not receive an EasyStartup DVD with your server, you can download an image from the Lenovo Support Web site at: http://www.lenovo.
• Initiates an unattended installation of the operating system and device drivers Setup and configuration When you start the EasyStartup DVD, you will be prompted for the following: • Select the language in which you want to view the program. • Select the language of the keyboard you will be using with the program. Note: The following language keyboards are supported: English, Dutch, French, German, Italian, Japanese, Spanish, and Turkish.
Typical operating system installation When you select Install operating system, you will be prompted for information required for the installation. The prompts vary depending on the operating system selected. This section describes the tasks associated with a typical Windows operating system installation. Each task must be completed in order before moving to the next task. Note: Ensure that your RAID controller is correctly configured before you select an operating system to install.
3. From Family list, select ThinkServer RS210, and click Continue. 4. Select the operating system that you want from the Operating system list, and click Continue. 5. Click Operating system installation to download instructions to install the operating system. Updating the firmware The firmware in the server is periodically updated and is available for download on the Lenovo Support Web site. Go to http://www.lenovo.
Before distributing the firmware update to other servers, ensure that your server can restart successfully without encountering hardware problems. Starting the backup server firmware The system board contains a backup copy area for the server firmware. This is a secondary copy of the server firmware that you update only during the process of updating the server firmware. If the primary copy of the server firmware becomes damaged, use this backup copy.
DIMMs DIMMs Heatsink Orientation Microprocessor The following table describes the jumpers on the system board. Table 25. System board jumpers Jumper number Jumper name Jumper setting JP1 Clear CMOS jumper 1 • Pins 1 and 2: Keep CMOS data (default). • Pins 2 and 3: Clear CMOS data (including power-on password and administrator password) JP6 Boot block jumper 2 • Pins 1 and 2: Boot from primary BIOS page (default) . • Pins 2 and 3: Boot from backup BIOS page. Notes: 1.
• DIMM error assistance. The Unified Extensible Firmware Interface (UEFI) disables a failing DIMM that is detected during POST, and the IMM lights the associated system error LED and the failing DIMM error LED. • System-event log (SEL). • ROM-based IMM firmware flash updates. • Auto Boot Failure Recovery (ABR). • A virtual media key, which enables remote presence support (remote video, remote keyboard/mouse, and remote storage). • Nonmaskable interrupt (NMI) detection and reporting.
You also can use the ASU program to configure the optional remote presence features or other IMM settings. The remote presence features provide enhanced systems-management capabilities. In addition, the ASU program provides limited settings for configuring the IPMI function in the IMM through the command-line interface. Use the command-line interface to issue setup commands. You can save any of the settings as a file and run the file as a script.
Note: This specific version is required. 5. Use Windows Update to install all available critical updates. 6. Launch the EasyManage installation. 7. After ThinkServer EasyManage is installed, enable Security and Patch Manager to obtain the LANDesk 8.8 Software Updates. In the console application, click Help -> LANDesk -> Security Updates for a guide to configuring Security and Patch Manager. 8.
Uninstalling the LANDesk Software Agent If the Core Server has LANDesk agents on it from a previous Management Suite release, it will fail the autorun prerequisite check. You must remove the old agents by running uninstallwinclient.exe file from the \Program Files\LANDesk\ManagementSuite folder. Using the remote presence capability and blue-screen capture The remote presence and blue-screen capture features are integrated functions of the integrated management module (IMM).
Step 2. When the prompt Setup is displayed, press F1. (This prompt is displayed on the screen for only a few seconds. You must press F1 quickly.) If you have set both a power-on password and an administrator password, you must type the administrator password to access the full Setup utility menu. Step 3. From the Setup utility main menu, select System Settings. Step 4. On the next screen, select Integrated Management Module. Step 5. On the next screen, select Network Configuration. Step 6.
Note: Changes are made periodically to the Lenovo Web site. The actual procedure might vary slightly from what is described in this document. 1. Go to http://www.lenovo.com/support. 2. Enter your product number (machine type and model number) or select Servers and Storage from the Select your product list. 3. From Family list, select ThinkServer RS210, and click Continue. Enabling and configuring Serial over LAN (SOL) Establish a Serial over LAN (SOL) connection to manage servers from a remote location.
g. Select Exit Setup; then, press Enter. h. Make sure that Yes, exit the Setup Utility is selected; then, press Enter.
Appendix A. Notices Lenovo may not offer the products, services, or features discussed in this document in all countries. Consult your local Lenovo representative for information on the products and services currently available in your area. Any reference to a Lenovo product, program, or service is not intended to state or imply that only that Lenovo product, program, or service may be used.
Trademarks The following terms are trademarks of Lenovo in the United States, other countries, or both: Lenovo Lenovo logo ThinkServer The following terms are trademarks of International Business Machines Corporation in the United States, other countries, or both: ®IBM ™ServeRAID ®Intel and ®Intel Xeon are trademarks of ®Intel Corporation in the United States, other countries, or both. ®Microsoft and Windows are trademarks of ®Microsoft Corporation in the United States, other countries, or both.
Product recycling and disposal This unit must be recycled or discarded according to applicable local and national regulations. Lenovo encourages owners of information technology (IT) equipment to responsibly recycle their equipment when it is no longer needed. Lenovo offers a variety of programs and services to assist equipment owners in recycling their IT products. Information on Lenovo product recycling offerings can be found on Lenovo's Internet site at http://www.lenovo.com/lenovo/environment/recycling.
Compliance with Republic of Turkey Directive on the Restriction of Hazardous Substances Meets requirements of the Republic of Turkey Directive on the Restriction of the Use of Certain Hazardous Substances In Electrical and Electronic Equipment (EEE). Türkiye EEE Yönetmeli ğ ine Uygunluk Beyan ı Bu Lenovo ürünü, T.C. Çevre ve Orman Bakanl ığı 'nın “Elektrik ve Elektronik E ş yalarda Baz ı Zararl ı Maddelerin Kullan ımının S ınırland ırılmas ına Dair Yönetmelik (EEE) ” direktiflerine uygundur .
Battery return program This product may contain a lithium or lithium ion battery. Consult your user manual or service manual for specific battery information. The battery must be recycled or disposed of properly. Recycling facilities may not be available in your area. For information on disposal or batteries outside the United States, go to http://www.lenovo.com/lenovo/environment or contact your local waste disposal facility. For Taiwan: Please recycle batteries.
and accumulators on the environment and human health due to the potential presence of hazardous substances. For proper collection and treatment, go to http://www.lenovo.com/lenovo/environment. For California: Perchlorate material - special handling may apply. See http://www.dtsc.ca.gov/hazardouswaste/perchlorate/. The foregoing notice is provided in accordance with California Code of Regulations Title 22, Division 4.5 Chapter 33. Best Management Practices for Perchlorate Materials.
United Kingdom telecommunications safety requirement Notice to Customers This apparatus is approved under approval number NS/G/1234/J/100003 for indirect connection to public telecommunication systems in the United Kingdom. European Union EMC Directive conformance statement This product is in conformity with the protection requirements of EU Council Directive 2004/108/EC on the approximation of the laws of the Member States relating to electromagnetic compatibility.
Dieses Gerät ist berechtigt, in Übereinstimmung mit dem Deutschen EMVG das EG-Konformitätszeichen - CE - zu führen. Verantwortlich für die Konformitätserklärung nach Paragraf 5 des EMVG ist die Lenovo (Deutschland) GmbH, Gropiusplatz 10, D-70563 Stuttgart. Informationen in Hinsicht EMVG Paragraf 4 Abs. (1) 4: Das Gerät erfüllt die Schutzanforderungen nach EN 55024 und EN 55022 Klasse A. Nach der EN 55022: “Dies ist eine Einrichtung der Klasse A.
People's Republic of China Class A warning statement Korea Class A warning statement Appendix A.
230 Hardware Maintenance Manual
Part Number: RS210 Printed in USA (1P) P/N: RS210 *RS210*
