Lenovo ideapad FLEX 5-1470 Lenovo ideapad FLEX 5-1570 Hardware Maintenance Manual
Notes: • Before using this information and the product it supports, be sure to read the general information under “Notices” on page 77. • This manual applies to the following models: Lenovo ideapad FLEX 5-1470/Lenovo ideapad FLEX 5-1570. The illustrations used in this manual are for Lenovo ideapad FLEX 5-1470 unless otherwise stated. First Edition (March 2017) © Copyright Lenovo 2017. All rights reserved.
Contents About this manual........................................ iv Safety information......................................... 1 General safety................................................. 2 Electrical safety............................................... 3 Safety inspection guide................................... 5 Handling devices that are sensitive to electrostatic discharge..................................... 6 Grounding requirements..................................
About this manual This manual contains service and reference information for the following Lenovo products: Lenovo ideapad FLEX 5-1470/Lenovo ideapad FLEX 5-1570 Use this manual to troubleshoot problems. The manual is divided into the following sections: • The common sections provide general information, guidelines, and safety information required for servicing computers. • The product-specific section includes service, reference, and product-specific parts information.
Safety information Safety information This chapter presents the following safety information that you need to get familiar with before you service a Lenovo ideapad FLEX 5-1470/Lenovo ideapad FLEX 5-1570 computer: • “General safety” on page 2 • “Electrical safety” on page 3 • “Safety inspection guide” on page 5 • “Handling devices that are sensitive to electrostatic discharge” on page 6 • “Grounding requirements” on page 6 • “Safety notices: multilingual translations” on page 7 • “Laser compliance st
Lenovo ideapad FLEX 5-1470/Lenovo ideapad FLEX 5-1570 Hardware Maintenance Manual General safety Follow these rules below to ensure general safety: • Observe a good housekeeping in the area where the machines are put during and after the maintenance. • When lifting any heavy object: 1. Make sure that you can stand safely without slipping. 2. Distribute the weight of the object equally between your feet. 3. Use a slow lifting force. Never move suddenly or twist when you attempt to lift it. 4.
Safety information Electrical safety Observe the following rules when working on electrical equipments. Important: Use only approved tools and test equipments. Some hand tools have handles covered with a soft material that does not insulate you when working with live electrical currents. Many customers have rubber floor mats near their machines that contain small conductive fibers to decrease electrostatic discharges. Do not use such kind of mat to protect yourself from electrical shock.
Lenovo ideapad FLEX 5-1470/Lenovo ideapad FLEX 5-1570 Hardware Maintenance Manual • Always look carefully for possible hazards in your work area. Examples of these hazards are moist floors, nongrounded power extension cables, power surges, and missing safety grounds. • Do not touch live electrical circuits with the reflective surface of a plastic dental mirror. The surface is conductive; such touching can cause personal injury and machine damage.
Safety information Safety inspection guide The purpose of this inspection guide is to assist you in identifying potential unsafe conditions. As each machine was designed and built, required safety items were installed to protect users and service personnel from injury. This guide addresses only those items. You should use good judgment to identify potential safety hazards according to the attachment of non-Lenovo features or options not covered by this inspection guide.
Lenovo ideapad FLEX 5-1470/Lenovo ideapad FLEX 5-1570 Hardware Maintenance Manual Handling devices that are sensitive to electrostatic discharge Any computer part containing transistors or integrated circuits (ICs) should be considered sensitive to electrostatic discharge (ESD). ESD damage can occur when there is a difference in charge between objects. Protect against ESD damage by equalizing the charge so that the machine, the part, the work mat, and the person handling the part are all at the same charge.
Safety information Safety notices: multilingual translations The safety notices in this section are provided in English, French, German, Hebrew, Italian, Japanese, and Spanish. Safety notice 1 Before the computer is powered on after FRU replacement, make sure all screws, springs, and other small parts are in place and are not left loose inside the computer. Verify this by shaking the computer and listening for rattling sounds. Metallic parts or metal flakes can cause electrical shorts.
Lenovo ideapad FLEX 5-1470/Lenovo ideapad FLEX 5-1570 Hardware Maintenance Manual Safety notice 2 DANGER Some standby batteries contain a small amount of nickel and cadmium. Do not disassemble a standby battery, recharge it, throw it into fire or water, or shortcircuit it. Dispose of the battery as required by local ordinances or regulations. Use only the battery in the appropriate parts listing. Use of an incorrect battery can result in ignition or explosion of the battery.
Safety information Safety notice 3 DANGER The battery pack contains small amounts of nickel. Do not disassemble it, throw it into fire or water, or short-circuit it. Dispose of the battery pack as required by local ordinances or regulations. Use only the battery in the appropriate parts listing when replacing the battery pack. Use of an incorrect battery can result in ignition or explosion of the battery. La batterie contient du nickel. Ne la démontez pas, ne l’exposez ni au feu ni à l’eau.
Lenovo ideapad FLEX 5-1470/Lenovo ideapad FLEX 5-1570 Hardware Maintenance Manual Safety notice 4 DANGER The lithium battery can cause a fire, an explosion, or a severe burn. Do not recharge it, remove its polarized connector, disassemble it, heat it above 100°C (212°F), incinerate it, or expose its cell contents to water. Dispose of the battery as required by local ordinances or regulations. Use only the battery in the appropriate parts listing.
Safety information Safety notice 5 If the LCD breaks and the fluid from inside the LCD gets into your eyes or on your hands, immediately wash the affected areas with water at least for 15 minutes. Seek medical care if any symptoms caused by the fluid are present after washing. Si le panneau d’affichage à cristaux liquides se brise et que vous recevez dans les yeux ou sur les mains une partie du fluide, rincez-les abondamment pendant au moins quinze minutes.
Lenovo ideapad FLEX 5-1470/Lenovo ideapad FLEX 5-1570 Hardware Maintenance Manual Safety notice 6 DANGER To avoid shock, do not remove the plastic cover that protects the lower part of the inverter card. Afin d’éviter tout risque de choc électrique, ne retirez pas le cache en plastique protégeant la partie inférieure de la carte d’alimentation. Aus Sicherheitsgründen die Kunststoffabdeckung, die den unteren Teil der Spannungswandlerplatine umgibt, nicht entfernen.
Safety information Safety notice 8 DANGER Before removing any FRU, turn off the computer, unplug all power cords from electrical outlets, remove the battery pack, and then disconnect any interconnecting cables. Avant de retirer une unité remplaçable en clientèle, mettez le système hors tension, débranchez tous les cordons d’alimentation des socles de prise de courant, retirez la batterie et déconnectez tous les cordons d’interface.
Lenovo ideapad FLEX 5-1470/Lenovo ideapad FLEX 5-1570 Hardware Maintenance Manual Laser compliance statement Some models of Lenovo computer are equipped from the factory with an optical storage device such as a CD-ROM drive or a DVD-ROM drive. Such devices are also sold separately as options. If one of these drives is installed, it is certified in the U.S.
Safety information A CD-ROM drive, a DVD-ROM drive, or any other storage device installed may contain an embedded Class 3A or Class 3B laser diode. Note the following: DANGER Emits visible and invisible laser radiation when open. Do not stare into the beam, do not view directly with optical instruments, and avoid direct exposure to the beam. Radiação por raio laser ao abrir. Não olhe fixo no feixe de luz, não olhe diretamente por meio de instrumentos óticos e evite exposição direta com o feixe de luz.
Lenovo ideapad FLEX 5-1470/Lenovo ideapad FLEX 5-1570 Hardware Maintenance Manual Important service information This chapter presents the following important service information: • “Strategy for replacing FRUs” on page 16 – “Strategy for replacing a hard disk drive” on page 17 – “Important notice for replacing a system board” on page 17 • “Important information about replacing RoHS compliant FRUs” on page 18 Important: BIOS and device driver fixes are customer-installable.
Important service information Use the following strategy to prevent unnecessary expense for replacing and servicing FRUs: • If you are instructed to replace an FRU, but the replacement does not solve the problem, reinstall the original FRU before you continue. • Some computers have both a processor board and a system board. If you are instructed to replace either of them, and replacing one of them does not solve the problem, reinstall that board, and then replace the other one.
Lenovo ideapad FLEX 5-1470/Lenovo ideapad FLEX 5-1570 Hardware Maintenance Manual Important information about replacing RoHS compliant FRUs RoHS, The Restriction of Hazardous Substances in Electrical and Electronic Equipment Directive (2002/95/EC) is a European Union legal requirement affecting the global electronics industry. RoHS requirements must be implemented on Lenovo products placed on the market after June 2006. Products on the market before June 2006 are not required to have RoHS compliant parts.
General checkout General checkout This chapter presents the following information: • “What to do first” on page 20 • “Power system checkout” on page 21 Before you go to the checkout, make sure to read the following important notes: Important notes: • Only certified trained personnel can service the computer. • Before replacing any FRU, read the entire page on removing and replacing FRUs. • Carefully remove screws for reuse when replacing FRUs.
Lenovo ideapad FLEX 5-1470/Lenovo ideapad FLEX 5-1570 Hardware Maintenance Manual What to do first When you do return an FRU, you must include the following information in the parts exchange form or parts return form that you attach to it: 1. Name and phone number of servicer 2. Date of service 3. Date on which the machine failed 4. Date of purchase 5. Procedure index and page number in which the failing FRU was detected 6. Failing FRU name and part number 7.
General checkout Power system checkout To verify a symptom, follow the steps below: 1. Turn off the computer. 2. Connect the AC adapter. 3. Make sure that power is supplied when you turn on the computer. 4. Turn off the computer. 5. Disconnect the AC adapter. 6. Make sure that the battery pack supplies power when you turn on the computer.
Lenovo ideapad FLEX 5-1470/Lenovo ideapad FLEX 5-1570 Hardware Maintenance Manual Checking operational charging To check whether the battery charges properly during operation, use a discharged battery pack or a battery pack that has less than 50% of the total power remaining when installed in the computer. Perform operational charging. If the battery status indicator or icon is not lit, remove the battery pack and let it return to room temperature. Reinstall the battery pack.
Related service information Related service information This chapter presents the following information: • “Restoring the factory contents by using OneKey Recovery” on page 23 • “Passwords” on page 24 • “Power management” on page 25 Restoring the factory contents by using OneKey Recovery Restore of factory default The Lenovo ideapad FLEX 5-1470/Lenovo ideapad FLEX 5-1570 computer comes with pre-installed OneKey Recovery System.
Lenovo ideapad FLEX 5-1470/Lenovo ideapad FLEX 5-1570 Hardware Maintenance Manual Passwords As many as three passwords may be needed for any Lenovo computer: the power-on password (POP), the hard disk password (HDP), and the supervisor password. If any of these passwords has been set, a prompt for it appears on the screen whenever the computer is turned on. The computer does not start until the password is entered.
Related service information Power management Note: Power management modes are not supported for an APM operating system. Putting the computer to sleep or shutting it down When you have finished working with your computer, you can put it to sleep or shut it down. Putting your computer to sleep If you will be away from your computer for only a short time, put the computer to sleep. When the computer is in sleep mode, you can quickly wake it to resume use, bypassing the startup process.
Lenovo ideapad FLEX 5-1470/Lenovo ideapad FLEX 5-1570 Hardware Maintenance Manual Lenovo ideapad FLEX 5-1470/Lenovo ideapad FLEX 5-1570 This chapter presents the following product-specific service references and product-specific parts information: • “Specifications” on page 26 • “Status indicators” on page 27 • “Keyboard function keys” on page 28 • “FRU replacement notices” on page 29 • “Removing and replacing an FRU” on page 30 • “Locations” on page 62 • “Parts list” on page 65 Specifications The
Lenovo ideapad FLEX 5-1470/Lenovo ideapad FLEX 5-1570 Status indicators The system status indicators below show the computer status: 1 2 Table 2. Status indicators Indicator Indicator status On (solid white) On (solid amber) Battery status indicator Charge status Charging Discharging Blinking slowly (white) Charging Blinking slowly (amber) Charging 1 Power status indicator 2 Blinking quickly (amber) Off On (solid white) Blinking Off Meaning The battery has more than 80% charge.
Lenovo ideapad FLEX 5-1470/Lenovo ideapad FLEX 5-1570 Hardware Maintenance Manual Keyboard function keys You can access certain system settings quickly by pressing the appropriate function keys. Table 3. Fn key combinations Fn + B: Fn + P: Fn + C: Fn + S: Fn + : Fn + : Fn + : Fn + : Fn + Space (on select models): Activates the break function. Activates the pause function. Enables/disables the scroll lock. Activates the system request. Activates the Pgup key function. Activates the Pgdn key function.
Lenovo ideapad FLEX 5-1470/Lenovo ideapad FLEX 5-1570 FRU replacement notices This section presents notices related to removing and replacing parts. Read this section carefully before replacing any FRU. Screw notices Loose screws can cause a reliability problem. In the Lenovo computer, this problem is addressed with special nylon-coated screws that have the following characteristics: • They maintain tight connections. • They do not easily come loose, even with shock or vibration.
Lenovo ideapad FLEX 5-1470/Lenovo ideapad FLEX 5-1570 Hardware Maintenance Manual Removing and replacing an FRU This section presents exploded figures with the instructions to indicate how to remove and replace the FRU. Make sure to observe the following general rules: 1. Do not attempt to service any computer unless you have been trained and certified. An untrained person runs the risk of damaging parts. 2. Before replacing any FRU, review “FRU replacement notices” on page 29. 3.
Lenovo ideapad FLEX 5-1470/Lenovo ideapad FLEX 5-1570 1010 Base cover Figure 1. Removal steps of base cover Remove the screws 1. 1 1 1 1 1 1 1 1 1 1 Step 1 Screw (quantity) Color M2.0 x 6.0 mm, Phillips-head, nylok-coated (10) LOW TO UPPER Black/ 1.0-1.5 kgf*cm Silver Torque Remove the base cover 2.
Lenovo ideapad FLEX 5-1470/Lenovo ideapad FLEX 5-1570 Hardware Maintenance Manual Note: Applying labels to the base cover If you see the following labels on base cover, it needs to be peeled off from the old base cover, and put on the new base cover. a OS label b Indonesia label c WLAN label d BT label e China Office label For some models, you also need to apply one or two FCC labels.
Lenovo ideapad FLEX 5-1470/Lenovo ideapad FLEX 5-1570 1020 Battery pack For access, remove this FRU: • “1010 Base cover” on page 31 DANGER Only use the battery specified in the parts list for your computer. Any other battery could ignite or explode. Figure 2. Removal steps of battery pack Unplug the battery pack connector in the direction shown by arrow 1. Remove the screws 2. Release the cable from the cable guides, then remove the battery pack in the direction shown by arrow 3.
Lenovo ideapad FLEX 5-1470/Lenovo ideapad FLEX 5-1570 Hardware Maintenance Manual 1030 Solid state disk For access, remove these FRUs in order: • “1010 Base cover” on page 31 • “1020 Battery pack” on page 33 Figure 3. Removal steps of solid state disk Remove the screw 1. 1 Step 1 Screw (quantity) Color Torque M1.98 x 3.0 mm, Phillips-head, nylok-coated (1) SSD TO MB Black 1.0-1.5 kgf*cm Remove the solid state disk in the direction shown by arrow 2.
Lenovo ideapad FLEX 5-1470/Lenovo ideapad FLEX 5-1570 1040 Hard disk drive For access, remove these FRUs in order: • “1010 Base cover” on page 31 • “1020 Battery pack” on page 33 Attention: • Do not drop the hard disk drive or apply any physical shock to it. The hard disk drive is sensitive to physical shock. Improper handling can cause damage and permanent loss of data. • Before removing the drive, suggest the customer to backup all the information on it if possible.
Lenovo ideapad FLEX 5-1470/Lenovo ideapad FLEX 5-1570 Hardware Maintenance Manual 1050 PCI Express Mini Card for wireless LAN For access, remove these FRUs in order: • “1010 Base cover” on page 31 • “1020 Battery pack” on page 33 Important: The preinstalled WLAN module may only be replaced with a Lenovo approved module in order to comply with FCC and IC regulations. Refer to “Table 5. Parts list—Overall” on page 67 for Lenovo part numbers for the approved modules. Figure 5.
Lenovo ideapad FLEX 5-1470/Lenovo ideapad FLEX 5-1570 Figure 5. Removal steps of PCI Express Mini Card for wireless LAN (continued) Disconnect the two wireless LAN cables (black, white) 2, and then remove the screw 3. 2 2 3 In step 2, unplug the jacks by using the removal tool antenna RF connector (P/N: 08K7159), or pick up the connectors with your fingers and gently unplug them in the direction shown by the arrows. Notes: The wireless LAN card has 2 cables in step 2.
Lenovo ideapad FLEX 5-1470/Lenovo ideapad FLEX 5-1570 Hardware Maintenance Manual 1060 Speakers For access, remove these FRUs in order: • “1010 Base cover” on page 31 • “1020 Battery pack” on page 33 Figure 6. Removal steps of speakers Unplug the speaker connector in the direction shown by arrow 1. Release the speaker cable from the cable guides and peel off the tape that secures the cable. 1 When installing: Make sure that the connector is attached firmly. Remove the two speakers 2.
Lenovo ideapad FLEX 5-1470/Lenovo ideapad FLEX 5-1570 1070 DIMM For access, remove these FRUs in order: • “1010 Base cover” on page 31 • “1020 Battery pack” on page 33 Figure 7. Removal steps of DIMM Carefully remove the DIMM EMI shielding 1.
Lenovo ideapad FLEX 5-1470/Lenovo ideapad FLEX 5-1570 Hardware Maintenance Manual Figure 7. Removal steps of DIMM (continued) Release the two latches on both edges of the socket at the same time in the directions shown by arrows 2, and then unplug the DIMM in the direction shown by arrow 3. 2 3 2 When installing: Insert the notched end of the DIMM into the socket. Push the DIMM firmly, and pivot it until it snaps into place. Make sure that it is firmly fixed in the slot and is difficult to move.
Lenovo ideapad FLEX 5-1470/Lenovo ideapad FLEX 5-1570 1080 Fan and Heat Sink assembly For access, remove these FRUs in order: • “1010 Base cover” on page 31 • “1020 Battery pack” on page 33 Figure 8. Removal steps of fan and heat sink assembly Remove the screws 1. 1 1 1 1 Step 1 1 Screw (quantity) Color Torque M1.98 x 3.0 mm, Phillips-head, nylok-coated (5) THERMAL MODULE TO CPU BRK/THERMAL MODULE TO GPU BRK (for DIS only) Black 1.0-1.
Lenovo ideapad FLEX 5-1470/Lenovo ideapad FLEX 5-1570 Hardware Maintenance Manual Figure 8. Removal steps of fan and heat sink assembly (continued) Remove the heat sink module in the direction shown by arrow 2. 2 Attention: Do not handle the heat sink assembly roughly. Improper handling can cause distortion or deformation and imperfect contact with components. a b When installing: Before you attach the fan assembly to the computer, apply thermal grease, at an amount of 0.
Lenovo ideapad FLEX 5-1470/Lenovo ideapad FLEX 5-1570 Figure 8. Removal steps of fan and heat sink assembly (continued) Unplug the fan connector in the direction shown by arrow 3. Remove the screws 4. Release the LCD cable from the cable guides. 4 4 3 Step 4 Screw (quantity) Color Torque M1.98 × 3.0 mm, Phillips head, nylok-coated (2) FAN TO upper Black 1.0-1.5 kgf*cm When installing: Make sure that the connector is attached firmly. Remove the fan 5.
Lenovo ideapad FLEX 5-1470/Lenovo ideapad FLEX 5-1570 Hardware Maintenance Manual 1090 IO board For access, remove these FRUs in order: • “1010 Base cover” on page 31 • “1020 Battery pack” on page 33 • “1080 Fan and Heat Sink assembly” on page 41 Figure 9. Removal steps of IO board Peel off the adhesive tape that secures the RTC battery 1. 1 Disconnect the IO board connector in the directions shown by arrows 2 and 3. Remove the screw 4. 4 2 3 Step 4 44 Screw (quantity) Color Torque M2.0 x 3.
Lenovo ideapad FLEX 5-1470/Lenovo ideapad FLEX 5-1570 Figure 9. Removal steps of IO board (continued) Remove the IO board 5. 5 Unplug the RTC battery connector in the direction shown by arrow 6, then remove the RTC battery.
Lenovo ideapad FLEX 5-1470/Lenovo ideapad FLEX 5-1570 Hardware Maintenance Manual 1100 System board Important notices for handling the system board: When handling the system board, bear the following in mind. • Be careful not to drop the system board on a bench top that has a hard surface, such as metal, wood, or composite. • Avoid rough handling of any kind. • During the whole process, make sure not to drop or stack the system board.
Lenovo ideapad FLEX 5-1470/Lenovo ideapad FLEX 5-1570 Figure 10. Removal steps of system board (continued) Remove the screws 5. 5 5 Step 5 5 Screw (quantity) Color Torque M1.98 x 3.0 mm, Phillips-head, nylok-coated (3) MB TO UPPER Black 1.0-1.5 kgf*cm Remove the system board 6.
Lenovo ideapad FLEX 5-1470/Lenovo ideapad FLEX 5-1570 Hardware Maintenance Manual 1110 Upper case For access, remove these FRUs in order: • “1010 Base cover” on page 31 • “1020 Battery pack” on page 33 • “1030 Solid state disk” on page 34 • “1040 Hard disk drive” on page 35 • “1050 PCI Express Mini Card for wireless LAN” on page 36 • “1060 Speakers” on page 38 • “1080 Fan and Heat Sink assembly” on page 41 • “1090 IO board” on page 44 • “1100 System board” on page 46 Figure 11.
Lenovo ideapad FLEX 5-1470/Lenovo ideapad FLEX 5-1570 Figure 11. Removal steps of upper case (continued) Open the hinges 2. 2 2 Rotate the upper case in the direction shown by arrows upper case. 3.
Lenovo ideapad FLEX 5-1470/Lenovo ideapad FLEX 5-1570 Hardware Maintenance Manual 1120 DC-in cable For access, remove these FRUs in order: • “1010 Base cover” on page 31 • “1020 Battery pack” on page 33 • “1030 Solid state disk” on page 34 • “1040 Hard disk drive” on page 35 • “1050 PCI Express Mini Card for wireless LAN” on page 36 • “1060 Speakers” on page 38 • “1080 Fan and Heat Sink assembly” on page 41 • “1090 IO board” on page 44 • “1100 System board” on page 46 • “1110 Upper case” on page 4
Lenovo ideapad FLEX 5-1470/Lenovo ideapad FLEX 5-1570 1130 LCD unit For access, remove these FRUs in order: • “1010 Base cover” on page 31 • “1020 Battery pack” on page 33 • “1030 Solid state disk” on page 34 • “1050 PCI Express Mini Card for wireless LAN” on page 36 • “1060 Speakers” on page 38 • “1080 Fan and Heat Sink assembly” on page 41 • “1100 System board” on page 46 • “1110 Upper case” on page 48 Figure 13. Removal steps of LCD unit Remove the hinge cover with tweezers 1.
Lenovo ideapad FLEX 5-1470/Lenovo ideapad FLEX 5-1570 Hardware Maintenance Manual Figure 13. Removal steps of LCD unit (continued) Remove the screws 3. 3 3 3 3 Step 3 Screw (quantity) Color Torque M2.0 × 2.5 mm, Phillips-head, nylok-coated (4) LCD BEZELTO COVER Black 1.0-1.5 kgf*cm Gently pull out the two pieces of adhesive tape with tweezers in the direction shown by arrows 4.
Lenovo ideapad FLEX 5-1470/Lenovo ideapad FLEX 5-1570 Figure 13. Removal steps of LCD unit (continued) Lift the LCD unit 5.
Lenovo ideapad FLEX 5-1470/Lenovo ideapad FLEX 5-1570 Hardware Maintenance Manual 1140 Camera board, sensor board and EDP cable For access, remove these FRUs in order: • “1010 Base cover” on page 31 • “1020 Battery pack” on page 33 • “1030 Solid state disk” on page 34 • “1040 Hard disk drive” on page 35 • “1050 PCI Express Mini Card for wireless LAN” on page 36 • “1060 Speakers” on page 38 • “1080 Fan and Heat Sink assembly” on page 41 • “1090 IO board” on page 44 • “1100 System board” on page 46 •
Lenovo ideapad FLEX 5-1470/Lenovo ideapad FLEX 5-1570 Figure 14. Removal steps of camera board, sensor board and EDP cable (continued) Remove the camera board 3. 3 Unplug the connector in the direction shown by arrow 4. 4 Remove the sensor board 5.
Lenovo ideapad FLEX 5-1470/Lenovo ideapad FLEX 5-1570 Hardware Maintenance Manual Figure 14. Removal steps of camera board, sensor board and EDP cable (continued) Peel off the tape 6 and 7. 7 6 6 Detach the two connectors in the direction shown by arrows 8.
Lenovo ideapad FLEX 5-1470/Lenovo ideapad FLEX 5-1570 Figure 14. Removal steps of camera board, sensor board and EDP cable (continued) Remove the EDP cable 9.
Lenovo ideapad FLEX 5-1470/Lenovo ideapad FLEX 5-1570 Hardware Maintenance Manual 1150 LCD hinges For access, remove these FRUs in order: • “1010 Base cover” on page 31 • “1020 Battery pack” on page 33 • “1030 Solid state disk” on page 34 • “1040 Hard disk drive” on page 35 • “1050 PCI Express Mini Card for wireless LAN” on page 36 • “1060 Speakers” on page 38 • “1080 Fan and Heat Sink assembly” on page 41 • “1090 IO board” on page 44 • “1100 System board” on page 46 • “1110 Upper case” on page 48
Lenovo ideapad FLEX 5-1470/Lenovo ideapad FLEX 5-1570 Figure 15. Removal steps of LCD hinges (continued) Then release the hinges in the direction shown by arrows 2.
Lenovo ideapad FLEX 5-1470/Lenovo ideapad FLEX 5-1570 Hardware Maintenance Manual 1160 Fingerprint module (on select models) For access, remove these FRUs in order: • “1010 Base cover” on page 31 • “1020 Battery pack” on page 33 Figure 16. Removal steps of fingerprint module Remove the screw 1, then remove the fingerprint bracket 2. Step 1 60 Screw (quantity) Color Torque M2.0 x 2.5 mm, Phillips-head, nylok-coated (1) FINGER PINTER TO UPPER Silver 1.0-1.
Lenovo ideapad FLEX 5-1470/Lenovo ideapad FLEX 5-1570 Figure 16. Removal steps of fingerprint module (continued) Remove the fingerprint board 3.
Lenovo ideapad FLEX 5-1470/Lenovo ideapad FLEX 5-1570 Hardware Maintenance Manual Locations Front and right-side view a Integrated camera b Built-in microphone c Wireless LAN antennas d Multi-touch screen e Touchpad f Kensington mini security slot g USB 3.0 port h Memory card slot 9 Novo button j Power button Note: For the description of each indicator, see “Status indicators” on page 27.
Lenovo ideapad FLEX 5-1470/Lenovo ideapad FLEX 5-1570 Bottom and left-side view a Speakers b AC power adapter jack c Battery status indicator Note: For the description of each indicator, see “Status indicators” on page 27. 4 HDMI port e USB 3.
Lenovo ideapad FLEX 5-1470/Lenovo ideapad FLEX 5-1570 Hardware Maintenance Manual Rear view a Ventilation slots 1 64
Lenovo ideapad FLEX 5-1470/Lenovo ideapad FLEX 5-1570 Parts list This section presents the following service parts: • “Overall” on page 66 • “LCD FRUs” on page 71 • “AC adapters” on page 73 • “Screws” on page 73 Notes: • Each FRU is available for all types or models, unless specific types or models are specified. Attention: Do not attempt to replace an FRU on your own. If an FRU is damaged, contact a Lenovo authorized servicer or a marketing representative for replacement or repair.
Lenovo ideapad FLEX 5-1470/Lenovo ideapad FLEX 5-1570 Hardware Maintenance Manual Overall 1 e 2 4 3 5 7 6 9 12 a 10 8 b 11 c 14 13 d 66
Lenovo ideapad FLEX 5-1470/Lenovo ideapad FLEX 5-1570 Table 5. Parts list—Overall No. FRU FRU no. a-e 1 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 see “Miscellaneous parts” on page 72. LCD unit (see “LCD FRUs” on page 71.
Lenovo ideapad FLEX 5-1470/Lenovo ideapad FLEX 5-1570 Hardware Maintenance Manual Table 5. Parts list—Overall (continued) No. FRU FRU no.
Lenovo ideapad FLEX 5-1470/Lenovo ideapad FLEX 5-1570 Table 5. Parts list—Overall (continued) No. FRU FRU no.
Lenovo ideapad FLEX 5-1470/Lenovo ideapad FLEX 5-1570 Hardware Maintenance Manual Table 5. Parts list—Overall (continued) No. FRU FRU no.
Lenovo ideapad FLEX 5-1470/Lenovo ideapad FLEX 5-1570 LCD FRUs In Lenovo ideapad FLEX 5-1470/Lenovo ideapad FLEX 5-1570, there are following types of LCDs. • “14.0-in. HD/FHD LED” • “15.6-in.
Lenovo ideapad FLEX 5-1470/Lenovo ideapad FLEX 5-1570 Hardware Maintenance Manual Table 6. Parts list—LCD FRUs No. FRU FRU no.
Lenovo ideapad FLEX 5-1470/Lenovo ideapad FLEX 5-1570 AC adapters Table 8. Parts list—AC adapters FRU P/N CRU ID. * Lenovo Lenovo ideapad ideapad FLEX 5- FLEX 51470 1570 Screws Table 9. Parts list—Screws FRU P/N Screw Pack C 80X8 Screw Pack C 80XB 5S10N67498 5S10N71293 CRU ID.
Lenovo ideapad FLEX 5-1470/Lenovo ideapad FLEX 5-1570 Hardware Maintenance Manual Power cords A Lenovo power cord for a specific country or region is usually available only in that country or region: Table 10. Parts list—3-pin power cords Region • 74 P/N CRU ID.
Lenovo ideapad FLEX 5-1470/Lenovo ideapad FLEX 5-1570 Table 10. Parts list—3-pin power cords (continued) Region P/N CRU ID.
Lenovo ideapad FLEX 5-1470/Lenovo ideapad FLEX 5-1570 Hardware Maintenance Manual Table 10. Parts list—3-pin power cords (continued) Region 76 P/N CRU ID.
Notices Notices Lenovo may not offer the products, services, or features discussed in this document in all countries. Consult your local Lenovo representative for information on the products and services currently available in your area. Any reference to a Lenovo product, program, or service is not intended to state or imply that only that Lenovo product, program, or service may be used.
Lenovo ideapad FLEX 5-1470/Lenovo ideapad FLEX 5-1570 Hardware Maintenance Manual Trademarks The following terms are either registered trademarks or trademarks of Lenovo in the United States and/or other countries: Lenovo® Lenovo logo® OneKey The following term is trademark of Microsoft Corporation in the United States, other countries, or both: Windows® The following term is trademark of Intel Corporation or its subsidiaries in the United States, other countries, or both: Intel® Other company, product, or
