User Guide Types 8009, 8791, 8795, 8799 Types 8803, 8807, 8812
User Guide Types 8009, 8791, 8795, 8799 Types 8803, 8807, 8812
Note Before using this information and the product it supports, be sure to read the “Important safety information” on page v and Appendix B, “Notices,” on page 65. First Edition (June 2006) © Copyright Lenovo 2005, 2006. Portions © Copyright International Business Machines Corporation 2005. All rights reserved. U.S. GOVERNMENT USERS – RESTRICTED RIGHTS: Our products and/or services are provided with RESTRICTED RIGHTS.
Contents Important safety information . . . . . . v Conditions that require immediate action . . . . . v General safety guidelines . . . . . . . . . . vi Service . . . . . . . . . . . . . . . vi Power cords and power adapters . . . . . . vii Extension cords and related devices . . . . . viii Plugs and outlets . . . . . . . . . . . viii Batteries . . . . . . . . . . . . . . viii Heat and product ventilation . . . . . . . ix CD and DVD drive safety . . . . . . . . . ix Additional safety information. . . . . .
Using the documentation and diagnostic programs . . . . . . . . . . . Calling for service . . . . . . . . Using other services . . . . . . . Purchasing additional services . . . . . . . . . . . . . . . . 55 55 56 56 MNP/V.42/V.42bis/V.44 Fax Class 1 commands Fax Class 2 commands Voice commands. . . commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60 61 61 62 Appendix B. Notices . . . . . . . . . 65 Appendix A. Manual modem commands . . . . . . . . . . . . .
Important safety information Note Please read the following important safety information first. This information can help you safely use your desktop or notebook personal computer. Follow and retain all information included with your computer. The information in this document does not alter the terms of your purchase agreement or the Lenovo™ Statement of Limited Warranty. For more information, refer to the warranty and safety information that is provided with your computer. Customer safety is important.
In the unlikely event that you notice any of the following conditions, or if you have any safety concerns with your product, stop using the product and unplug it from the power source and telecommunication lines until you can speak to the Customer Support Center for further guidance. v Power cords, plugs, power adapters, extension cords, surge protectors, or power supplies that are cracked, broken, or damaged. v Signs of overheating, smoke, sparks, or fire.
Danger Hazardous moving parts. Keep fingers and other body parts away. Attention Before replacing any CRUs, turn off the computer and wait three to five minutes to let the computer cool before opening the cover. Power cords and power adapters Use only the power cords and power adapters supplied by the product manufacturer. The power cords shall be safety approved. For Germany, it shall be H05VV-F, 3G, 0.75 mm2, or better. For other countries, the suitable types shall be used accordingly.
Extension cords and related devices Ensure that extension cords, surge protectors, uninterruptible power supplies, and power strips that you use are rated to handle the electrical requirements of the product. Never overload these devices. If power strips are used, the load should not exceed the power strip input rating. Consult an electrician for more information if you have questions about power loads, power requirements, and input ratings.
shorten the life of the battery and can also pose a safety hazard. Do not let rechargeable Lithium-Ion batteries completely discharge or store these batteries in a discharged state. Heat and product ventilation Computers generate heat when turned on and when batteries are charging. Notebook computers can generate a significant amount of heat due to their compact size.
v Remove CD and DVD discs from the computer when not in use. v Do not bend or flex CD and DVD discs, or force them into the computer or their packaging. v Check CD and DVD discs for cracks before each use. Do not use cracked or damaged discs. Additional safety information Danger Electrical current from power, telephone, and communication cables is hazardous.
Dispose of the battery as required by local ordinances or regulations. Modem safety information Caution To reduce the risk of fire, use only No. 26 AWG or larger telecommunication line cord. To reduce the risk of fire, electrical shock, or injury when using telephone equipment, always follow basic safety precautions, such as: v Never install telephone wiring during a lightning storm. v Never install telephone jacks in wet locations unless the jack is specifically designed for wet locations.
Power supply statement Never remove the cover on a power supply or any part that has the following label attached. Hazardous voltage, current, and energy levels are present inside any component that has this label attached. There are no serviceable parts inside these components. If you suspect a problem with one of these parts, contact a service technician.
Introduction This User Guide contains the following information: v Chapter 1, “Arranging your workspace,” on page 1 provides information about setting up your computer for comfort and the impact of light sources, air circulation, and electrical outlets. v Chapter 2, “Setting up your computer,” on page 3 provides information about setting up your computer and software and operating system installation.
xiv User Guide
Chapter 1. Arranging your workspace To get the most from your computer, arrange both the equipment you use and your work area to suit your needs and the kind of work you do. Your comfort is of foremost importance, but light sources, air circulation, and the location of electrical outlets also can affect the way you arrange your workspace. Comfort Although no single working position is ideal for everyone, here are a few guidelines to help you find a position that suits you best.
Where it is impossible to avoid reflections or to adjust the lighting, an antiglare filter placed over the screen might be helpful. However, these filters might affect the clarity of the image on the screen; try them only after you have exhausted other methods of reducing glare. Dust buildup compounds problems associated with glare. Remember to clean your monitor screen periodically using a soft cloth moistened with a nonabrasive liquid glass cleaner. Air circulation Your computer and monitor produce heat.
Chapter 2. Setting up your computer Before you begin, make sure you set up your computer in the best possible work area that suits your needs and the kind of work you do. For more information, refer to Chapter 1, “Arranging your workspace,” on page 1. Note: Read “Important safety information” on page v before you set up your computer. The precautions and guidelines will help you work safely. Connecting your computer Use the following information when connecting your computer.
v If you have a Video Graphics Array (VGA) Standard monitor, connect the cable to the connector as shown. Note: If your model has two monitor connectors, be sure to use the connector on the accelerated graphics port (AGP) adapter. v If you have a digital video interface (DVI) monitor, connect the cable to the connector as shown. Note: Your computer must have an adapter installed that supports the DVI monitor. 5. If you have a modem, connect the modem using the following information.
1 2 3 This illustration shows the two connections on the back of the computer that are needed to set up your modem. In the United States and other countries or regions that use the RJ-11 telephone outlet, attach one end of the telephone cable to the telephone and the other end to the telephone connector on the back of the computer. Attach one end of the modem cable to the modem connector on the back of the computer and the other end to the telephone outlet.
6. If you have audio devices, attach them using the following instructions. For more information about speakers, see steps 7 and 8. 1 Audio line-in 2 Audio line-out 3 Microphone 4 Headphone This connector receives audio signals from an external audio device, such as a stereo system. This connector sends audio signals from the computer to external devices, such as powered stereo speakers.
b. Connect the speakers to the computer. 9. Connect any additional devices that you have. Your computer might not have all connectors that are shown. 1394 1394 1 USB 2 Serial 3 S-video 4 Parallel 5 Ethernet 6 MIDI/joystick 7 IEEE 1394 Use this connector to attach a device that requires a USB connection, such as a keyboard, mouse, scanner, printer, or personal digital assistant (PDA).
Note: Refer to the Access Help online help system for more information about connectors. See “Access Help” on page 54 for instructions on how to open the online help system. Turning on power Turn on the monitor and other external devices first, and then turn on the computer. When the power-on self-test (POST) is finished, the logo window closes. If your computer has preinstalled software, the software installation program starts.
v Record your computer machine type, model, and serial number. If you need service or technical support, you will probably be asked for this information. For further information, see the warranty and safety information that is provided with your computer. Updating your operating system Microsoft makes updates available for various operating systems through the Microsoft Windows Update Web site.
10 User Guide
Chapter 3. Installing options This chapter provides an introduction to the features and options that are available for your computer. You can expand the capabilities of your computer by adding memory or adapters. When installing an option, use these instructions along with the instructions that come with the option. Note: Use only parts provided by Lenovo. Important Before you install or remove any option, read “Important safety information” on page v.
v Internal hard disk drive v Optical drive (some models) Video subsystem v An integrated graphics controller for a Video Graphics Array (VGA) monitor Audio subsystem v HD with ADI 1983HD Audio Codec v Line in and line out connectors on the rear panel v Microphone and headphone connectors on the front panel v Mono internal speaker (some models) Connectivity v 10/100/1000 Mbps integrated Broadcom Ethernet controller that supports the Wake on LAN® feature (some models) v Soft modem V.90/V.
Security features v Keyboard with fingerprint reader (some models, see the Access Help online help system for information) v User and administrator passwords for BIOS access v Support for the addition of an integrated cable lock (Kensington lock) to secure the cover v Startup sequence control v Startup without diskette drive, keyboard, or mouse v v v v v Unattended start mode Hard disk I/O control Serial and parallel port I/O control Security profile by device Cover presence switch (some models) Preinstal
Specifications This section lists the physical specifications for your computer. Dimensions Height: 89 mm (3.5 in.) Width: 276 mm (10.9 in.) Depth: 273 mm (10.7 in) Weight Minimum configuration as shipped: 6.3 kg (13.4 lb) Maximum configuration: 6.4 kg (14.1 lb) Environment Air temperature: Operating at 0 - 3000 ft (914.4 m): 10° to 35°C (50° to 95°F) Operating at 3000 ft - 6562 ft (2000 m): 10° to 32°C (50° to 89.
– Peripheral component interconnect (PCI) adapters – Optical drives, such as CD drives and DVD drives (some models) For the latest information about available options, see the Lenovo Web site at http://www.lenovo.com/ or contact your reseller or marketing representative. Supported operating positions You can position your computer in one of the positions shown in the following illustration.
v Do not place the option on the computer cover or other metal surface. Installing external options This section shows the various external connectors on your computer to which you can attach external options, such as external speakers, a printer, or a scanner. For some external options, you must install additional software in addition to making the physical connection.
Locating the connectors on the rear of your computer The following illustration shows the locations of the connectors on the rear of the computer.
Connector Description USB connectors Used to attach a device that requires a Universal Serial Bus (USB) connection, such as a USB mouse, USB keyboard, USB scanner, or USB printer. If you have more than eight USB devices, you can purchase a USB hub, which you can use to connect additional USB devices. Parallel connector Used to attach a parallel printer, parallel scanner, or other devices that use a 25-pin parallel connector.
Opening the cover Important: Read “Important safety information” on page v and “Handling static-sensitive devices” on page 15 before opening the computer cover. To open the computer cover: 1. Remove any media (DVDs, CDs, or tapes) from the drives, shut down your operating system, and turn off all attached devices and the computer. 2. Unplug all power cords from electrical outlets. 3. Disconnect all cables attached to the computer.
Locating components The following illustration will help you locate the various components in your computer. 1 PCI riser 2 Power supply assembly 3 Optical drive eject button 4 Optical drive 5 Hard disk drive 6 System fan 7 Internal speaker 8 Cable clip 9 Rear fan bracket assembly Identifying parts on the system board The system board (sometimes called the planar or motherboard) is the main circuit board in your computer.
The following illustration shows the locations of parts on the system board.
To install a memory module: 1. Open the computer cover. See “Opening the cover” on page 19. 2. Pivot the drive bay assembly upward to gain access to the system board. 3. Locate the memory connectors. See “Identifying parts on the system board” on page 20. 4. Open the retaining clips. 5. Make sure that the notch 1 on the memory module aligns correctly with the connector key 2 on the system board. Push the memory module straight down into the connector until the retaining clips close.
What to do next: v To work with another option, go to the appropriate section. v To complete the installation, go to “Closing the cover and connecting the cables” on page 31. Installing a PCI adapter This section provides information and instructions for installing a PCI adapter. Your computer has a riser card with one PCI expansion connector. To install an adapter: 1. Open the computer cover. See “Opening the cover” on page 19. 2. Pivot the drive bay assembly upward to gain access to the system board. 3.
5. Pull upward on the blue handle provided to remove the PCI riser from the computer. 6. Pivot the adapter latch 1 upward then remove the cover for the expansion connector. 7. Remove the adapter from its static-protective package. 8. Install the adapter into the expansion connector in the PCI riser. 9. Pivot the adapter latch 1 down to retain the adapter. 10. Reinstall the PCI riser and the adapter. What to do next: v To work with another option, go to the appropriate section.
Installing an optical drive This section provides information and instructions for installing optical drives. You can install an optical drive to read other types of media, such as CD drives and DVD drives. Note: These different drives are also referred to as integrated drive electronics (IDE) drives. When you install an optical drive, it is important to note the type of drive that you are installing. To install an optical drive, do the following: 1. Open the computer cover.
4. Slide the optical drive out of the front of the computer. 5. See “Locating components” on page 20. 6. Slide the optical drive in the front of the computer until it is locked into position.
What to do next: v To work with another option, go to the appropriate section. v To complete the installation, go to “Closing the cover and connecting the cables” on page 31. Security features To help prevent hardware theft and unauthorized access to your computer, several security options are available. In addition to a physical lock, unauthorized use of your computer can be prevented by a software lock that locks the keyboard until a correct password is typed in.
Password protection To deter unauthorized use of your computer, you can use the Setup Utility program to set a password. When you turn on your computer you are prompted to type the password to unlock the keyboard for normal use. For more information, see Chapter 5, “Using the Setup Utility,” on page 41. What to do next: v To work with another option, go to the appropriate section. v To complete the installation, go to “Closing the cover and connecting the cables” on page 31.
3. Locate the PCI riser. See “Locating components” on page 20. 4. Remove the PCI riser to gain access to the battery. See “Installing a PCI adapter” on page 23. 5. Locate the battery. See “Identifying parts on the system board” on page 20. 6. Remove the old battery using the following illustration. 7. Install the new battery using the following illustration. 8. Reinstall the PCI riser. 9. Close the computer cover, and plug in the power cord. See “Closing the cover and connecting the cables” on page 31.
Erasing a lost or forgotten password (clearing CMOS) This section applies to lost or forgotten passwords. For more information about lost or forgotten passwords, see the ThinkVantage Productivity Center program on your desktop. Note: If you are enrolled in the Hardware Password Reset program, refer to “Using passwords” on page 41 to reset your password. If you do clear CMOS or restore Setup Utility defaults, you will have to re-enroll in the Hardware Password Reset program. To erase a forgotten password: 1.
Closing the cover and connecting the cables After working with options, you need to install any removed parts, close the computer cover, and reconnect any cables, including telephone lines and power cords. Also, depending on the option that is installed, you might need to confirm the updated information in the Setup Utility program. To close the computer cover and connect cables to your computer: 1.
32 User Guide
Chapter 4. Recovering software The Rescue and Recovery program is software aimed at helping users restore their computer data and recover from software or hardware-related failures. In the event of a computer failure, use the Rescue and Recovery program to restore the contents of the primary hard drive to a previously saved state. This chapter will help you become familiar with recovery solutions provided by Lenovo.
Attention: When you restore the factory contents from the Product Recovery discs, all files currently on the hard disk will be deleted and replaced by the original factory contents. During the restore process, you will be given the opportunity to save one or more files currently on your hard disk drive to other media before any data is removed. 1. Insert the Rescue and Recovery disc into your CD or DVD drive. 2. Restart your computer. 3. After a short delay, the Rescue and Recovery workspace opens.
3. Follow the instructions on the screen. For information about performing a restore operation from the Rescue and Recovery workspace, see “Using the Rescue and Recovery workspace.” Using the Rescue and Recovery workspace The Rescue and Recovery workspace resides in a protected, hidden area of your hard disk that operates independently from the Windows operating system. This enables you to perform recovery operations even if the Windows operating system cannot be started.
v To restore your hard disk from a Rescue and Recovery backup or to restore your hard drive to the factory contents, click Restore your system in the Rescue and Recovery menu; then, follow the instructions on the screen. Note: After restoring your hard disk to the original factory content, you might have to reinstall some software or drivers. Refer to the following notes for more information. v For information about other features of the Rescue and Recovery workspace, click Help. Notes: 1.
1. From the Windows desktop, click Start, click All Programs, click ThinkVantage, then click Create Recovery Media. 2. In the Rescue Media area, select the type of rescue media you want to create. You can create rescue media using a CD, USB hard drive, or an internal hard drive. 3. Click OK. 4. Follow the instructions on the screen. To use rescue media, do one of the following: v Insert the rescue disc and restart your computer.
and Recovery workspace. For information about creating and using rescue media, see “Creating and using rescue media” on page 36. Recovering or installing device drivers Before you can recover or install device drivers, your operating system must be installed on your computer. Make sure that you have the documentation and software media for the device. Device drivers for factory-installed devices are located on the computer hard disk (usually drive C) in the SWTOOLS\drivers folder.
7. Use the down-arrow key to select Save and exit the Setup Utility, then press Enter. 8. When the Setup Confirmation window appears, press Enter. 9. The computer restarts. Note: If you are using an external device, you first must turn off your computer before connecting the external device. For more information on Setup Utility, see Chapter 5, “Using the Setup Utility,” on page 41. Chapter 4.
40 User Guide
Chapter 5. Using the Setup Utility The Setup Utility program is stored in the electrically erasable programmable read-only memory (EEPROM) of your computer. The Setup Utility program is used to view and change the configuration settings of your computer, regardless of which operating system you are using. However, the operating-system settings might override any similar settings in the Setup Utility program. Starting the Setup Utility program To start the Setup Utility program, do the following: 1.
v v v v Setup Utility program and hard disk drive passwords are not case sensitive Not be your name or your user name Not be a common word or a common name Be significantly different from your previous password User Password When a User Password is set, the user is prompted to type a valid password each time the computer is turned on. The computer cannot be used until a valid password is typed from the keyboard.
Note: Selecting a startup device from the Startup Device menu does not permanently change the startup sequence. Changing the startup device sequence To view or permanently change the configured startup device sequence, do the following: 1. Start the Setup Utility program (see “Starting the Setup Utility program” on page 41). 2. Select Startup. 3. Select Startup Sequence. See the information displayed on the right side of the screen. 4.
44 User Guide
Chapter 6. Updating system programs This chapter contains information about updating POST/BIOS and how to recover from a POST/BIOS update failure. Using system programs System programs are the basic layer of software that is built into your computer. They include the power-on self-test (POST), the basic input/output system (BIOS) code, and the Setup Utility program. POST is a set of tests and procedures that is performed each time you turn on your computer.
46 User Guide
Chapter 7. Troubleshooting and diagnostics This chapter describes some basic troubleshooting and diagnostic programs. If your computer problem is not described here, see Chapter 8, “Getting information, help, and service,” on page 53 for additional troubleshooting resources. Basic troubleshooting The following table provides information to help you troubleshoot your computer problem. Symptom Action The computer does not start when you press the power button.
Symptom Action The Enhanced Performance USB Keyboard does not work. Verify that: v The computer is turned on. v The keyboard is securely connected to a USB connector on the front or rear of the computer. v No keys are stuck. If you cannot correct the problem, have the computer serviced. Refer to the warranty and safety information that is provided with your computer for a list of service and support telephone numbers. The mouse does not work. The computer does not respond to the mouse.
PC-Doctor for Windows PC-Doctor for Windows is a diagnostic program that works through the Windows operating system. The PC-Doctor for Windows diagnostic program enables you to view symptoms and solutions for computer problems, access the Lenovo troubleshooting center, update system drivers, and review system information. To open PC-Doctor for Windows, click Start from the Windows desktop, select All Programs, select PC-Doctor for Windows, and click PC-Doctor for Windows.
6. Follow the instructions on the screen. 7. When prompted, insert a blank, formatted diskette into the diskette drive and continue to follow the instructions on the screen. 8. When the operation is complete, remove the diskette and click Quit. 9. Insert another blank, formatted diskette into the diskette drive and continue to follow the instructions on the screen. 10. When the operation is complete, remove the diskette and click Quit.
Optical mouse An optical mouse uses a light-emitting diode (LED) and an optical sensor to navigate the pointer. If the pointer on the screen does not move smoothly with the optical mouse, you might need to clean the mouse. Use the following procedure to clean the optical mouse: 1. Turn off your computer. 2. Disconnect the mouse cable from the computer. 3. Turn the mouse upside down to look at the lens. a. If there is a smudge on the lens, gently clean the area with a plain cotton-tipped swab. b.
To clean a mouse with a ball, follow the instructions below: 1. Turn off your computer. 2. Disconnect the mouse cable from the computer. 3. Turn the mouse upside down. Twist the retainer ring 1 to the unlocked position to remove the ball. 4. Place your hand over the retainer ring and ball 2 , and then turn the mouse right-side up, so that the retainer ring and ball fall out into your hand. 5. Wash the ball in warm, soapy water then dry it with a clean cloth. 6.
Chapter 8. Getting information, help, and service If you need help, service, or technical assistance or just want more information about products manufactured by Lenovo, you will find a wide variety of sources available from Lenovo to assist you. Information resources This section provides information on how to access useful resources relating to your computing needs. Online Books folder The Online Books folder provides publications to help you set up and use your computer.
v v v v Client Security Solutions Factory Recovery System Updates Service and support Note: ThinkVantage Technologies are only available on select Lenovo computers. To access the ThinkVantage Productivity Center program, click Start, select All Programs, select ThinkVantage, and click Productivity Center.
Using the documentation and diagnostic programs Many computer problems can be solved without outside assistance. If you experience a problem with your computer, see Chapter 7, “Troubleshooting and diagnostics,” on page 47. For information on additional resources to help you troubleshoot your computer problem, see “Information resources” on page 53. If you suspect a software problem, see the documentation, including README files and online help, that comes with the operating system or application program.
Note: Phone numbers are subject to change without notice. If the number for your country or region is not provided, contact your Lenovo reseller or Lenovo marketing representative.
Appendix A. Manual modem commands This appendix provides commands for manually programming your modem. Commands are accepted by the modem while it is in Command Mode. Your modem is automatically in Command Mode until you dial a number and establish a connection. Commands can be sent to your modem from a PC running communication software or any other terminal devices. All commands sent to the modem must begin with AT and end with ENTER. All commands can be typed in either upper or lower case, but not mixed.
Command Function H1 Force modem off-hook (make busy) Note: H1 command is not supported for Italy I_ L_ M_ I0 Display product-identification code I1 Factory ROM checksum test I2 Internal memory test I3 Firmware ID I4 Reserved ID L0 Low speaker volume L1 Low speaker volume L2 Medium speaker volume L3 High speaker volume M0 Internal speaker off M1 Internal speaker on until carrier detected M2 Internal speaker always on M3 Internal speaker on until carrier detected and off while d
Extended AT commands Command Function &C0 Force Carrier Detect Signal High (ON) &C1 Turn on CD when remote carrier is present &D0 Modem ignores the DTR signal &D1 Modem returns to Command Mode after DTR toggle &D2 Modem hangs up, returns to the Command Mode after DTR toggle &D3 Resets modem after DTR toggle &F_ &F Recall factory default configuration &G_ &G0 Guard tone disabled &G1 Guard tone disabled &G2 1800 Hz guard tone &K0 Disable flow control &K3 Enable RTS/CTS hardware flow
Command Function &W_ %E_ &V1 Display Last Connection Statistics &W0 Stores the active profile as Profile 0 &W1 Stores the active profile as Profile 1 %E0 Disable auto-retrain %E1 Enable auto-retrain +MS? Displays the current Select Modulation settings +MS=? Displays a list of supported Select Modulation options +MS=a,b,c,e,f Select modulation where: a=0, 1, 2, 3, 9, 10, 11, 12, 56, 64, 69; b=0-1; c=300-56000; d=30056000; e=0-1; and f=0-1. A, b, c, d, e, f default=12, 1, 300, 56000, 0, 0.
Fax Class 1 commands +FAE=n Data/Fax Auto Answer +FCLASS=n Service Class +FRH=n Receive data with HDLC framing +FRM=n Receive data +FRS=n Receive silence +FTH=n Transmit data with HDLC framing +FTM=n Transmit data +FTS=n Stop transmission and wait Fax Class 2 commands +FCLASS=n Services class. +FAA=n Adaptive answer. +FAXERR Fax error value. +FBOR Phase C data bit order. +FBUF? Buffer size (read only). +FCFR Indicate confirmation to receive. +FCLASS= Service class.
+FPHCTO Phase C time out. +FPOLL Indicates polling request. +FPTS: Page transfer status. +FPTS= Page transfer status. +FREV? Identify revision. +FSPT Enable polling. +FTSI: Report the transmit station ID.
Attention Switzerland User: If your Swisscom phone line does not have Taxsignal switched OFF, modem function may be impaired. The impairment may be resolved by a filter with the following specifications: Telekom PTT SCR-BE Taximpulssperrfilter-12kHz PTT Art. 444.112.7 Bakom 93.0291.Z.N Appendix A.
64 User Guide
Appendix B. Notices Lenovo may not offer the products, services, or features discussed in this document in all countries. Consult your local Lenovo representative for information on the products and services currently available in your area. Any reference to a Lenovo product, program, or service is not intended to state or imply that only that Lenovo product, program, or service may be used.
vary significantly. Some measurements may have been made on development-level systems and there is no guarantee that these measurements will be the same on generally available systems. Furthermore, some measurements may have been estimated through extrapolation. Actual results may vary. Users of this document should verify the applicable data for their specific environment. Television output notice The following notice applies to models that have the factory-installed television-output feature.
Index A Access Help 54 adapters connector 23 installing 23 peripheral component interconnect (PCI) antivirus software, updating 9 arranging your workspace 1 audio line in connector 18 audio line out connector 18 audio, subsystem 12 15, 23 diagnostic diskettes creating 49 running 50 DIMMS 21 downloading device drivers 18 drives bays 12 CD 15 DVD 15 internal 11 E B electrical intput 14 environment, operating 14 Ethernet connector 18 exiting, Setup Utility 43 BIOS, updating (flashing) 45 C cables 3, 31 c
N non-optical mouse notices 65 51 O Online Books folder 53 Opening the cover 19 operating system installing 9 updating 9 optical mouse 51 options available 14 external 14, 16, 17 internal 14 T ThinkVantage Productivity Center 53 trademarks 66 troubleshooting 47 U P parallel connector 18 password administrator 42 considerations 41 erasing 30 lost or forgotten 30 protection 28 setting, changing, deleting 42 user 42 PCI expansion connector (PCI) 23 PCI riser 24 physical specifications 14 planar 20 power A
Part Number: 41X6122 Printed in USA (1P) P/N: 41X6122