Hardware Maintenance Manual Lenovo B480
Note: Before using this information and the product it supports, be sure to read the general information under Appendix A “Notices” on page 93. Second Edition (October 2012) © Copyright Lenovo 2012. LIMITED AND RESTRICTED RIGHTS NOTICE: If data or software is delivered pursuant a General Services Administration “GSA” contract, use, reproduction, or disclosure is subject to restrictions set forth in Contract No. GS-35F-05925.
Contents About this manual. . . . . . . . . . . iii Chapter 1. Safety information . . . . . . 1 General safety . . . . . . . . . . . . . . . Electrical safety . . . . . . . . . . . . . . Safety inspection guide . . . . . . . . . . . Handling devices that are sensitive to electrostatic discharge. . . . . . . . . . . . . . . . . Grounding requirements . . . . . . . . . . . Safety notices (multilingual translations) . . . . . Laser compliance statement (multilingual translations) . . . . . . . . . . . . . .
ii Hardware Maintenance Manual
About this manual This manual provides service and reference information for the following Lenovo® products. Machine Machine type (MT) Lenovo B480 4359, 20140 Use this manual to troubleshoot problems. The manual is divided into the following sections: • The common sections provide general information, guidelines, and safety information required for servicing computers. • The product-specific section includes service, reference, and product-specific parts information.
iv Hardware Maintenance Manual
Chapter 1. Safety information This chapter presents following safety information that you need to be familiar with before you service a Lenovo Notebook.
Electrical safety Observe the following rules when working on electrical equipment. Important: Use only approved tools and test equipment. Some hand tools have handles covered with a soft material that does not insulate you when working with live electrical currents. Many customers have, near their equipment, rubber floor mats that contain small conductive fibers to decrease electrostatic discharges. Do not use this type of mat to protect yourself from electrical shock.
– Use caution; do not become a victim yourself. – Switch off power. – Send another person to get medical aid. Safety inspection guide The purpose of this inspection guide is to assist you in identifying potentially unsafe conditions. As each machine was designed and built, required safety items were installed to protect users and service technicians from injury. This guide addresses only those items.
2. Make sure that the ESD protective devices you use have been certified (ISO 9000) as fully effective. When handling ESD-sensitive parts: • Keep the parts in protective packages until they are inserted into the product. • Avoid contact with other people. • Wear a grounded wrist strap against your skin to eliminate static on your body. • Prevent the part from touching your clothing. Most clothing is insulative and retains a charge even when you are wearing a wrist strap.
DANGER DANGER DANGER DANGER DANGER Chapter 1.
DANGER 6 Hardware Maintenance Manual
Chapter 1.
PERIGO PERIGO PERIGO PERIGO PERIGO PERIGO 8 Hardware Maintenance Manual
PERIGO PERIGO DANGER DANGER DANGER Chapter 1.
DANGER DANGER DANGER DANGER DANGER VORSICHT 10 Hardware Maintenance Manual
VORSICHT VORSICHT VORSICHT VORSICHT Chapter 1.
VORSICHT VORSICHT VORSICHT 12 Hardware Maintenance Manual
Chapter 1.
14 Hardware Maintenance Manual
Chapter 1.
16 Hardware Maintenance Manual
Chapter 1.
18 Hardware Maintenance Manual
Laser compliance statement (multilingual translations) The laser compliance statements in this section are provided in the following languages: • English • Arabic • Brazilian Portuguese • French • German • Hebrew • Japanese • Korean • Spanish • Traditional Chinese Chapter 1.
20 Hardware Maintenance Manual
Chapter 1.
22 Hardware Maintenance Manual
Chapter 1.
24 Hardware Maintenance Manual
Chapter 1.
26 Hardware Maintenance Manual
Chapter 2. Important service information This chapter presents the following important service information that applies to all machine types supported by this manual: • “Strategy for replacing FRUs” on page 27 – “Strategy for replacing a hard disk drive” on page 28 – “Important notice for replacing a system board” on page 28 • “Important information about replacing RoHS compliant FRUs” on page 28 Important: BIOS and device driver fixes are customer-installable.
• If an adapter or a device consists of more than one FRU, any of the FRUs may be the cause of the error. Before replacing the adapter or device, remove the FRUs, one by one, to see if the symptoms change. Replace only the FRU that changed the symptoms. Strategy for replacing a hard disk drive Always try to run a low-level format before replacing a hard disk drive (HDD). This will cause all customer data on the hard disk to be lost.
Chapter 3. General checkout This chapter presents following information: • “What to do first” on page 29 • “Power system checkout” on page 30 Before you go to the checkout guide, be sure to read the following important notes. Important notes: • Only certified trained personnel should service the computer. • Before replacing any FRU, read the entire page on removing and replacing FRUs. • When you replace FRUs, it is recommended to use new nylon-coated screws.
• Diskette drive damage caused by pressure on the diskette drive cover, foreign material in the drive, or the insertion of a diskette with multiple labels • Damaged or bent diskette eject button • Fuses blown by attachment of a nonsupported device • Forgotten computer password (making the computer unusable) • Sticky keys caused by spilling a liquid onto the keyboard • Use of an incorrect ac power adapter on laptop products The following symptoms might indicate damage caused by nonwarranted activities: • Mis
Note: Noise from the ac power adapter does not always indicate a defect. Checking operational charging To check whether the battery charges properly during operation, use a discharged battery pack or a battery pack that has less than 50% of the total power remaining when installed in the computer. Perform operational charging. If the battery status indicator or icon does not turn on, remove the battery pack and let it return to room temperature. Reinstall the battery pack.
32 Hardware Maintenance Manual
Chapter 4. Related service information This chapter presents the following information: • “Recovering the computer settings” on page 33 • “Passwords” on page 33 • “Power management” on page 34 Recovering the computer settings This topic provides information about the recovery programs that are available for you to recover the computer settings.
If any of these passwords has been set, a prompt for it will be displayed on the screen whenever the computer is turned on. The computer does not start until the password is entered. Note: If only a supervisor password is set, the password prompt will not be displayed when the operating system is started. Power-on password A power-on password (POP) protects the system from being powered on by an unauthorized person. The password must be entered before an operating system can be booted.
Also, when the time set on the resume timer elapses, the computer automatically returns from sleep mode and resumes operation. Note: The computer does not accept any input immediately after it enters sleep mode. Wait a few seconds before taking any action to reenter operation mode. Hibernation mode In hibernation mode, the following occurs: • The system status, RAM, VRAM, and setup data are stored on the hard disk drive. • The system is powered off.
36 Hardware Maintenance Manual
Chapter 5. Lenovo B480 This chapter presents the following product-specific service references and parts information: • “Specifications” on page 37 • “Status indicators” on page 38 • “Fn key combinations” on page 39 Specifications This topic lists the physical features for the Lenovo B480 models. Processor • To view the processor information of your computer, do either of the following: – Windows 7: Click Start, right-click Computer. Then click Properties.
• HDMI port • External monitor connector • 4-in-1 digital media card reader slot Optical drive • 12.7 mm Rambo optical drive Wireless features • Integrated wireless LAN • 100/1000 Mbps Ethernet communication Security feature • Fingerprint reader Status indicators This chapter presents the system status indicators that show the status of the computer. 4 1 2 3 Table 1. Status indicators Indicator Meaning 1 Caps Lock indicator White: When the indicator is on, the Caps Lock mode is enabled.
Table 1. Status indicators (continued) Indicator Meaning 3 When this indicator is on, the hard disk drive or the optical drive is reading or writing data. Device access status indicator Attention: • When the indicator is on, do not put the computer into sleep mode or turn off the computer. • When the indicator is on, do not move the computer. Sudden physical shock might cause drive errors.
Table 2. Function key combinations (continued) Key combination Description Fn + up/down arrow Increase or decrease the display brightness level. Fn + left/right arrow Increase or decrease the sound volume.
Chapter 6. FRU replacement notices This chapter presents notices related to removing and replacing parts. Read this chapter carefully before replacing any FRU. CRU statement for customers: You can resolve some problems with your product with a replacement part you can install yourself, called a “Customer Replaceable Unit” or “CRU.” Some CRUs are designated as self-service CRUs and others are designated as optional-service CRUs. Installation of self-service CRUs is your responsibility.
• Torque driver If you have a torque screwdriver, refer to the Torque column in the screw information table for each step. • Make sure that you use the correct screw. It is recommended to use new screws for replacements. If you have a torque screwdriver, tighten all screws firmly to the torque specified in the screw information table for each step. • Ensure torque screw drivers are calibrated correctly following country specifications.
Chapter 7. Removing and replacing a FRU This chapter provides instructions on how to remove or replace a FRU. CRU statement for customers: You can resolve some problems with your product with a replacement part you can install yourself, called a “Customer Replaceable Unit” or “CRU.” Some CRUs are designated as self-service CRUs and others are designated as optional-service CRUs. Installation of self-service CRUs is your responsibility.
1010 Battery pack Removal steps of battery pack DANGER Use only the battery specified in the parts list for your computer. Any other battery could ignite or explode. Unlock the spring-loaded battery latch 1 . Holding the manual battery latch in the unlocked position, remove the battery pack in the direction shown by the arrow 2 . 1 2 2 When installing: Install the battery pack in the slot. Make sure that the battery latches are in the locked position.
Removal steps of bottom slot cover Remove the screws 1 , and then remove the cover 2 . 1 1 2 2 Step Screw (quantity) Color Torque 1 M2 × 3 mm, flat-head, nylon-coated (2) Black 1.85 kgf-cm 1030 Optical drive For access, remove these FRUs in order: • “1010 Battery pack” on page 44 • “1020 Bottom slot cover” on page 44 Removal steps of optical drive Remove the screw 1 . 1 Step Screw (quantity) Color Torque 1 M2 × 3 mm, flat-head, nylon-coated (1) Black 1.85 kgf-cm Chapter 7.
Insert a screwdriver into the screw hole 2 and push the optical drive in the direction shown by the arrow 3 . Then remove the optical drive. 2 3 Removal steps of optical drive bezel and optical drive bracket Remove the screws 1 and then remove the optical drive bracket. 1 2 1 Step Screw (quantity) Color Torque 1 M2 × 3 mm, flat-head, nylon-coated (2) Black 1.
Removal steps of memory modules Release the two latches on both edges of the socket at the same time in the direction shown by the arrows 1 , and then unplug the memory module in the direction shown by the arrow 2 . 1 1 2 Note: If only one memory module is used on the computer you are servicing, the card must be installed in SLOT-0 ( a : lower slot), but not in SLOT-1 ( b : upper slot). b a When installing: Insert the notched end of the memory module into the socket.
Removal steps of hard disk drive assembly Remove the screw 1 , then pull the tab in the direction shown by the arrow 2 . 2 1 Step Screw (quantity) Color Torque 1 M2 × 3 mm, flat-head, nylon-coated (1) Black 1.85 kgf-cm Remove the hard disk drive from the slot 3 . 3 When installing: Make sure that the hard disk drive connector is attached firmly. Removal steps of hard disk drive bracket Remove the screws 1 .
Remove the hard disk drive bracket as shown by the arrow 2 . 2 1060 PCI Express Mini Card for wireless LAN For access, remove these FRUs in order: • “1010 Battery pack” on page 44 • “1020 Bottom slot cover” on page 44 Removal steps of PCI Express Mini Card for wireless LAN In steps 1 , disconnect the cables from the card using the removal tool antenna RF connector (P/N: 08K7159) or pick up the cables with your fingers and then gently disconnecting the cable from the card in the direction of the arrows.
Remove the card in the direction shown by the arrow 3 . 3 When installing: Plug the black cable (MAIN) into the jack labeled A, and the white cable (AUX) into the jack labeled B on the card. 1070 mSATA solid-state drive For access, remove these FRUs in order: • “1010 Battery pack” on page 44 • “1020 Bottom slot cover” on page 44 Attention: • Do not drop the drive or apply any physical shock to it. The drive is sensitive to physical shock. Improper handling can cause damage and permanent loss of data.
Remove the mSATA solid-state drive 2 . 2 1080 Backup battery For access, remove these FRUs in order: • “1010 Battery pack” on page 44 • “1020 Bottom slot cover” on page 44 Removal steps of backup battery DANGER Use only the battery specified in the parts list for your computer. Any other battery could ignite or explode. Detach the connector 1 , and then remove the battery pack in the direction shown by the arrow 2 . 2 1 When installing: Make sure that the connector is attached firmly.
Removal steps of keyboard Remove the screws 1 . 1 1 1 When installing: Make sure that the screws have been fastened to secure the keyboard. Step Screw (quantity) Color Torque 1 M2.5 × 8 mm, flat-head, nylon-coated (3) Black 4.0 kgf-cm Carefully lift the keyboard until you can see how it’s connected. Hold the keyboard above the computer, and then detach the keyboard connector. 4 2 3 When installing: Make sure that the keyboard connector is attached firmly.
1100 Keyboard bezel For access, remove these FRUs in order: • “1010 Battery pack” on page 44 • “1020 Bottom slot cover” on page 44 • “1030 Optical drive” on page 45 • “1090 Keyboard” on page 51 Removal steps of keyboard bezel Remove the screws 1 and 2 that secure the keyboard bezel. 1 2 1 2 2 1 1 1 1 1 1 1 1 1 Step Screw (quantity) Color Torque 1 M2.5 × 8 mm, flat-head, nylon-coated (11) Black 4.0 kgf-cm 2 M2 × 3 mm, flat-head, nylon-coated (3) Black 1.85 kgf-cm Chapter 7.
Remove the screw 3 . 3 Step Screw (quantity) Color Torque 3 M2 × 6 mm, flat-head, nylon-coated (1) Black 1.85 kgf-cm Detach the connectors. 9 8 4 5 6 7 When installing: Make sure that all the connectors are attached firmly.
Remove the keyboard bezel. 10 1110 Fingerprint board and LED board For access, remove these FRUs in order: • “1010 Battery pack” on page 44 • “1020 Bottom slot cover” on page 44 • “1030 Optical drive” on page 45 • “1090 Keyboard” on page 51 • “1100 Keyboard bezel” on page 53 Chapter 7.
Removal steps of LED board Peel off the mylar tape 1 . Then remove the LED board 2 .
Removal steps of fingerprint board Remove the screw 1 and the fingerprint board bracket 2 . Then remove the fingerprint board 3 . 1 2 3 Step Screw (quantity) Color Torque 1 M2 × 3 mm, flat-head, nylon-coated (1) Silver 1.
1130 Microphone assembly For access, remove these FRUs in order: • “1010 Battery pack” on page 44 • “1020 Bottom slot cover” on page 44 • “1030 Optical drive” on page 45 • “1090 Keyboard” on page 51 • “1100 Keyboard bezel” on page 53 Removal steps of microphone assembly Detach the connector 1 , and then remove the microphone assembly in the direction shown by the arrow 2 . 2 1 When installing: Make sure that the connector is attached firmly to the system board.
Removal steps of I/O board Remove the screws 1 , and then detach the cable. 1 1 2 3 Step Screw (quantity) Color Torque 1 M2 × 6 mm, flat-head, nylon-coated (2) Black 1.85 kgf-cm When installing: Make sure that the cable is attached firmly to the system board. Chapter 7.
Remove the I/O board 4 . 4 1150 System board assembly and USB board Important notices for handling the system board: When handling the system board, bear the following in mind: • Be careful not to drop the system board on a bench top that has a hard surface, such as metal, wood, or composite. • Avoid rough handling of any kind. • At every point in the process, be sure not to drop or stack the system board.
Removal steps of system board assembly and USB board Remove the screws 1 , and then detach the connectors as shown in the following illustration. 2 9 8 3 4 1 1 6 5 7 Step Screw (quantity) Color Torque 1 M2 × 6 mm, flat-head, nylon-coated (2) Black 1.85 kgf-cm When installing: Make sure that all the connectors are attached firmly. Remove the system board in the direction shown by the arrow 10 . Then detach the DC-in cable 11 . 11 10 Chapter 7.
Remove the USB board as shown in the following illustration.
Loosen the screws 2 to 6 . 6 6 6 5 2 4 3 Lift the fan assembly in the direction shown by the arrow 7 . Note: Be careful not to damage the connector. 7 Chapter 7.
When installing: Before you attach the thermal module to the computer, apply thermal grease, at an amount of 0.2 grams, on the part marked a and b as shown in the following illustration. Either too much or too less application of grease can cause a thermal problem due to imperfect contact with a component.
• • • • “1100 Keyboard bezel” on page 53 “1130 Microphone assembly” on page 58 “1150 System board assembly and USB board” on page 60 “1160 Thermal module” on page 62 Attention: The CPU is extremely sensitive. When you service the CPU, avoid any kind of rough handling. Removal steps of CPU Rotate the head of the screw in the direction shown by the arrow 1 to release the lock, then remove the CPU 2 .
• • “1140 I/O board” on page 58 “1150 System board assembly and USB board” on page 60 Removal steps of LCD unit Release the antenna cables from the cable guides. Then remove the screws 1 . 1 1 1 1 Step Screw (quantity) Color Torque 1 M2.5 × 6 mm, flat-head, nylon-coated (4) Silver 4.0 kgf-cm When installing: • Route the antenna cables along the cable guides. As you route the cables, make sure that they are not subjected to any tension.
Remove the LCD unit in the direction shown by the arrow 2 .
Removal steps of speaker assembly Remove the screws 1 . Then remove the speaker assembly 2 . 1 2 1 1 2 1 Step Screw (quantity) Color Torque 1 M2.5 × 5.7 mm, flat-head, nylon-coated (4) Black 4.
Removal steps of DC-in connector and base cover Remove the screws 1 , and then remove the DC-in connector in the direction shown by the arrow 2 . 1 1 2 Step Screw (quantity) Color Torque 1 M2 × 3 mm, flat-head, nylon-coated (2) Black 1.85 kgf-cm Applying labels to the base cover The new base cover is shipped with a kit containing labels of several kinds. Apply those labels listed when you replace the base cover.
1 14 13 2 12 11 3 4 5 6 7 8 9 10 1 Indonesia D side label 8 Israel label 2 WWAN IMEI barcode label 9 Israel label 3 Brazil Bluetooth label or Bluetooth label for United States/Canade/Taiwan 10 Malaysia SIRIM label 4 China label, KCC label, or MAC label 11 Vodafone label 5 Brazil WLAN label or WLAN label for United States/Canade/Taiwan 13 Rating label I 6 PPT label 14 Rating label II 7 Indonesia WLAN and Bluetooth label 2010 LCD front bezel For access, remove these FRUs in order: • “1010 Batt
Removal steps of LCD front bezel Remove the screws 1 . 1 1 Step Screw (quantity) Color Torque 1 M2 × 3.5 mm, flat-head, nylon-coated (2) Black 1.85 kgf-cm Remove the LCD front bezel in the direction shown by the arrows 2 . 2 2 2 2 When installing: Make sure that all the latches are attached firmly. Then secure the bezel with the screws.
Removal steps of integrated camera Remove the integrated camera from the LCD cover as shown in the following illustration. Note: The integrated camera is stuck on the top center of the LCD cover. 1 2 When installing: Stick the integrated camera to the top center of the LCD cover and adjust the placement to make sure that the connector is attached firmly.
Removal steps of LCD panel and LCD cable Remove the screws 1 . Then remove the LCD panel in the direction shown by the arrow 2 . 1 1 2 1 1 Step Screw (quantity) Color Torque 1 M2 × 3.5 mm, flat-head, nylon-coated (4) White 1.85 kgf-cm Remove the LCD cable. 4 3 When installing: Make sure that the connector is attached firmly. Chapter 7.
Removal steps of hinges Remove the screws 1 . Then remove the hinges 2 . 2 1 1 2 1 1 Step Screw (quantity) Color Torque 1 M2 × 3.5 mm, flat-head, nylon-coated (4) White 1.
Removal steps of antenna assembly and LCD rear cover Release the antenna cables from the cable guides of the LCD rear cover assembly and from the hinges in the direction shown by the arrows 1 . 1 1 Cable routing: Route the antenna cables along the cable guides and secure the antenna boards with adhesive tapes. As you route the cables, make sure that they are not subjected to any tension. Tension could cause the cables to be damaged by the cable guides, or a wire to be broken. Chapter 7.
76 Hardware Maintenance Manual
Chapter 8. Locations This chapter presents the locations of the Lenovo B480 hardware components. Front view 2 1 2 11 10 9 3 4 8 7 6 5 Figure 1.
Right-side view 4 5 3 1 2 Figure 2. Lenovo B480 right-side view 1 Combo audio jack 4 USB connector 2 USB connector 5 ac power connector 3 Optical drive Bottom and left-side view 1 2 3 10 5 9 8 7 4 6 Figure 3. Lenovo B480 bottom and left-side view 1 Battery latch (manual) 6 Monitor connector 2 Battery pack 7 Ethernet connector 3 Battery latch (spring loaded) 8 HDMI port 4 Security keyhole 9 USB 3.
Chapter 9. Parts list This chapter contains following lists of the service parts. • “Overall” on page 80 • “LCD FRUs” on page 83 • “Keyboard” on page 85 • “Miscellaneous parts” on page 87 • “ac power adapters” on page 88 • “Power cords” on page 89 Note: Each FRU is available for all types or models, unless specific types or models are specified.
Overall 1 23 22 hi 2 gh 3 21 20 a 4 19 19 b 18 5 17 6 7 7 b c fg 8 c d 9 16 10 10 d e 11 11 fe 15 12 12 13 13 14 14 Table 3. Parts list—Overall No. FRU (Overall) FRU No. CRU ID 1 LCD unit (see “LCD FRUs” on page 83.) 2 LB48 Upper Case W/TP 6M.4TFCS.001 90200759 N 3 LB48 LED Board W/Cable 50.4TF03.
Table 3. Parts list—Overall (continued) No. FRU (Overall) FRU No. CRU ID 4 Finger print Authentec TCS5DA6D0 101500257 N 5 LA48 Thermal Module UMA W/FAN 90200765 N 5 LA48 Thermal Module DIS W/FAN 90200532 N 6 LB48 USB Board W/Cable 55.4TF03.001G 90000219 N 7 Battery, 6CELL 2.2Ah, Sanyo 2.2Ah 48Wh 6cell battey 121500047 * 7 Battery, 6CELL 2.2Ah, LG 2.2Ah 48Wh 6cell battey 121500049 * 7 Battery, 6CELL 2.2Ah, SMP 2.2Ah 48Wh 6cell battey 121500050 * 7 Battery, 6CELL 2.
Table 3. Parts list—Overall (continued) No. FRU (Overall) FRU No. CRU ID 16 HDD, 750G 5400rpm, WD ML375M, WD7500BPVT-08HXZ 16200121 ** 16 HDD, 750G 5400rpm, HGST Jaguar B, HTS541075A9E680 16200192 ** 16 HDD, 1TB 5400rpm, WD ML500M, WD10JPVT-08A1Y 16200120 ** 16 HDD, 1TB 5400rpm, HGST Jaquar B, HTS541010A9E680 16200193 ** 16 HDD, 320G 7200rpm, WD MX320S-1, WD3200BEKT-08PVM 16200092 ** 16 HDD, 320G 7200rpm, Toshiba Capricorn CS (H6sp), TSB MK3261GSY 7200PRM 9.
Table 3. Parts list—Overall (continued) No. FRU (Overall) FRU No.
1 2 7 j 3 6 4 5 Table 4. Parts list - LCD No. FRU FRU No. CRU ID 1 LB48 LCD Bezel W/Camera Hole 90200762 N 2 LB48 Hinge R+L 6K.4TFCS.001 90200760 N 3 LB48 Camera 0.3M 56.18011.472 90000224 N 4 LB48 Antenna R 25.90AAL.001 90200764 N 5 LB48 LCD Cover 60.4TF01.001 90200761 N 6 LB48 Antenna L 25.90AAK.001 90200763 N 7 Panel, 14.0 HD Flat Glossy, AUO, B140XW01 V8 18200207 N 7 Panel, 14.0 HD Flat Glossy, BOE HB140WX1-100 18200154 N 7 Panel, 14.
Keyboard Table 5. Parts list - Keyboard (Dafon) Language FRU NO. (Windows 7) FRU NO.
Table 6. Parts list - Keyboard (Sunrex) (continued) Language FRU NO. (Windows 7) FRU NO.
Table 7. Parts list - Keyboard (Chicony) (continued) Language FRU NO. (Windows 7) FRU NO.
Table 8. Parts list - Miscellaneous parts (continued) FRU FRU No. CRU ID (j) LB48 LCD Cable 50.4TF01.001 90200757 N LA48 LCD Mylar 40.4TD03.001 90200537 N LA48 Microphone Rubber 23.42383.001 90200538 N Note: Italicized letters in parentheses are references to the exploded view in “Overall” on page 80. ac power adapters Table 9. Parts list—2-pin (65 W) ac power adapters FRU FRU No.
Table 12. Parts list—3-pin (90 W) ac power adapters (continued) FRU FRU No. CRU ID Liteon PA-1900-54I, EPA model 36200030 * Delta ADP-90ZH DA, EPA model 36200031 * Chicony Power HP-BT090E13LF, EPA model 36200032 * Power cords A Lenovo power cord for a specific country or region is usually available only in that country or region. Table 13. Parts list - 3-pin power cords (Linetek) Country or region FRU No.
Table 13. Parts list - 3-pin power cords (Linetek) (continued) Country or region FRU No. CRU ID U.K. 145000593 * 145000594 * Country or region FRU No. CRU ID Argentina 145000567 * 145000557 * 145000564 * 145000553 * 145000568 * 145000566 * 145000560 * 145000563 * 145000559 * 145000555 * 145000558 * 145000554 * 145000565 * 145000556 * 145000561 * 145000562 * • LINETEK LP-61L+ H03VV-F+ LS15 1 m UL • LINETEK LP-30B + SPT-2 + LS15 1 m Table 14.
Table 15. Parts list - 3-pin power cords (Volex) Country or region FRU No. CRU ID Argentina 145000528 * 145000532 * 145000527 * 145000525 * 145000538 * 145000534 * 145000536 * 145000526 * 145000535 * 145000530 * 145000533 * 145000529 * 145000524 * 145000531 * 145000605 * 145000537 * Country or region FRU No.
Table 16. Parts list - 2-pin power cords (Linetek) (continued) Country or region FRU No. CRU ID Australia 145500023 * 145500028 * 145500018 * 145500022 * 145500020 * 145500029 * 145500026 * 145500025 * 145500027 * 145500021 * 145500019 * • LINETEK LP15A+H03VVH2-F+LS7 1 m Brazil • LINETEK LP25+H03VVH2-F+LS7H 1 m CCC • LINETEK PC205+RVV 0.75/2C+COC03 1 m CE • LINETEK LP21+H03VVH2-F+ LS7 1 m India • LINETEK LP28+IS:694 0.
Appendix A. Notices Lenovo may not offer the products, services, or features discussed in this document in all countries. Consult your local Lenovo representative for information on the products and services currently available in your area. Any reference to a Lenovo product, program, or service is not intended to state or imply that only that Lenovo product, program, or service may be used.
Electronic emissions notices For electronic emission information on Class B digital devices, refer to the corresponding information in the User Guide. Trademarks The following terms are trademarks of Lenovo in the United States, other countries or both: Lenovo OneKey Windows is the trademark of the Microsoft group of companies. Intel is the trademark of Intel Corporation or its subsidiaries in the United States, other countries, or both.
Part Number: Printed in China (1P) P/N: *1P*
