Lenovo E10-30 Hardware Maintenance Manual
Note: Before using this information and the product it supports, be sure to read the general information under “Notices” on page 81. First Edition (March 2014) © Copyright Lenovo 2014. All rights reserved. LENOVO products, data, computer software, and services have been developed exclusively at private expense and are sold to governmental entities as commercial items as defined by 48 C.F.R. 2.101 with limited and restricted rights to use, reproduction and disclosure.
Contents About this manual........................................iv Safety information.........................................1 General safety ...................................................... 2 Electrical safety .................................................... 3 Safety inspection guide ...................................... 5 Handling devices that are sensitive to electrostatic discharge......................................... 6 Grounding requirements ...................................
About this manual This manual contains service and reference information for the following Lenovo product: Lenovo E10-30 Use this manual to troubleshoot problems. The manual is divided into the following sections: • The common sections provide general information, guidelines, and safety information required for servicing computers. • The product-specific section includes service, reference, and product-specific parts information.
Safety information Safety information This chapter presents the following safety information that you need to get familiar with before you service a Lenovo computer: • “General safety” on page 2 • “Electrical safety” on page 3 • “Safety inspection guide” on page 5 • “Handling devices that are sensitive to electrostatic discharge” on page 6 • “Grounding requirements” on page 6 • “Safety notices: multilingual translations” on page 7 • “Laser compliance statement” on page 14 1
Lenovo E10-30 Hardware Maintenance Manual General safety Follow these rules below to ensure general safety: • Observe a good housekeeping in the area where the machines are put during and after the maintenance. • When lifting any heavy object: 1. Make sure that you can stand safely without slipping. 2. Distribute the weight of the object equally between your feet. 3. Use a slow lifting force. Never move suddenly or twist when you attempt to lift it. 4.
Safety information Electrical safety Observe the following rules when working on electrical equipments. Important: Use only approved tools and test equipments. Some hand tools have handles covered with a soft material that does not insulate you when working with live electrical currents. Many customers have rubber floor mats near their machines that contain small conductive fibers to decrease electrostatic discharges. Do not use such kind of mat to protect yourself from electrical shock.
Lenovo E10-30 Hardware Maintenance Manual • Always look carefully for possible hazards in your work area. Examples of these hazards are moist floors, nongrounded power extension cables, power surges, and missing safety grounds. • Do not touch live electrical circuits with the reflective surface of a plastic dental mirror. The surface is conductive; such touching can cause personal injury and machine damage.
Safety information Safety inspection guide The purpose of this inspection guide is to assist you in identifying potential unsafe conditions. As each machine was designed and built, required safety items were installed to protect users and service personnel from injury. This guide addresses only those items. You should use good judgment to identify potential safety hazards due to attachment of non-Lenovo features or options not covered by this inspection guide.
Lenovo E10-30 Hardware Maintenance Manual Handling devices that are sensitive to electrostatic discharge Any computer part containing transistors or integrated circuits (ICs) should be considered sensitive to electrostatic discharge (ESD). ESD damage can occur when there is a difference in charge between objects. Protect against ESD damage by equalizing the charge so that the machine, the part, the work mat, and the person handling the part are all at the same charge. Notes: 1.
Safety information Safety notices: multilingual translations The safety notices in this section are provided in English, French, German, Hebrew, Italian, Japanese, and Spanish. Safety notice 1 Before the computer is powered on after FRU replacement, make sure all screws, springs, and other small parts are in place and are not left loose inside the computer. Verify this by shaking the computer and listening for rattling sounds. Metallic parts or metal flakes can cause electrical shorts.
Lenovo E10-30 Hardware Maintenance Manual Safety notice 2 DANGER Some standby batteries contain a small amount of nickel and cadmium. Do not disassemble a standby battery, recharge it, throw it into fire or water, or short-circuit it. Dispose of the battery as required by local ordinances or regulations. Use only the battery in the appropriate parts listing. Use of an incorrect battery can result in ignition or explosion of the battery. Certaines batteries de secours contiennent du nickel et du cadmium.
Safety information Safety notice 3 DANGER The battery pack contains small amounts of nickel. Do not disassemble it, throw it into fire or water, or short-circuit it. Dispose of the battery pack as required by local ordinances or regulations. Use only the battery in the appropriate parts listing when replacing the battery pack. Use of an incorrect battery can result in ignition or explosion of the battery. La batterie contient du nickel. Ne la démontez pas, ne l’exposez ni au feu ni à l’eau.
Lenovo E10-30 Hardware Maintenance Manual Safety notice 4 DANGER The lithium battery can cause a fire, an explosion, or a severe burn. Do not recharge it, remove its polarized connector, disassemble it, heat it above 100°C (212°F), incinerate it, or expose its cell contents to water. Dispose of the battery as required by local ordinances or regulations. Use only the battery in the appropriate parts listing. Use of an incorrect battery can result in ignition or explosion of the battery.
Safety information Safety notice 5 If the LCD breaks and the fluid from inside the LCD gets into your eyes or on your hands, immediately wash the affected areas with water at least for 15 minutes. Seek medical care if any symptoms caused by the fluid are present after washing. Si le panneau d’affichage à cristaux liquides se brise et que vous recevez dans les yeux ou sur les mains une partie du fluide, rincez-les abondamment pendant au moins quinze minutes.
Lenovo E10-30 Hardware Maintenance Manual Safety notice 6 DANGER To avoid shock, do not remove the plastic cover that protects the lower part of the inverter card. Afin d’éviter tout risque de choc électrique, ne retirez pas le cache en plastique protégeant la partie inférieure de la carte d’alimentation. Aus Sicherheitsgründen die Kunststoffabdeckung, die den unteren Teil der Spannungswandlerplatine umgibt, nicht entfernen.
Safety information Safety notice 8 DANGER Before removing any FRU, turn off the computer, unplug all power cords from electrical outlets, remove the battery pack, and then disconnect any interconnecting cables. Avant de retirer une unité remplaçable en clientèle, mettez le système hors tension, débranchez tous les cordons d’alimentation des socles de prise de courant, retirez la batterie et déconnectez tous les cordons d’interface.
Lenovo E10-30 Hardware Maintenance Manual Laser compliance statement Some models of Lenovo computer are equipped from the factory with an optical storage device such as a CD-ROM drive or a DVD-ROM drive. Such devices are also sold separately as options. If one of these drives is installed, it is certified in the U.S. to conform to the requirements of the Department of Health and Human Services 21 Code of Federal Regulations (DHHS 21 CFR) Subchapter J for Class 1 laser products.
Safety information A CD-ROM drive, a DVD-ROM drive, or any other storage device installed may contain an embedded Class 3A or Class 3B laser diode. Note the following: DANGER Emits visible and invisible laser radiation when open. Do not stare into the beam, do not view directly with optical instruments, and avoid direct exposure to the beam. Radiação por raio laser ao abrir. Não olhe fixo no feixe de luz, não olhe diretamente por meio de instrumentos óticos e evite exposição direta com o feixe de luz.
Lenovo E10-30 Hardware Maintenance Manual Important service information This chapter presents the following important service information: • “Strategy for replacing FRUs” on page 16 – “Strategy for replacing a hard disk drive” on page 17 – “Important notice for replacing a system board” on page 17 • “Important information about replacing RoHS compliant FRUs” on page 18 Important: BIOS and device driver fixes are customer-installable.
Important service information Use the following strategy to prevent unnecessary expense for replacing and servicing FRUs: • If you are instructed to replace an FRU, but the replacement does not solve the problem, reinstall the original FRU before you continue. • Some computers have both a processor board and a system board. If you are instructed to replace either of them, and replacing one of them does not solve the problem, reinstall that board, and then replace the other one.
Lenovo E10-30 Hardware Maintenance Manual Important information about replacing RoHS compliant FRUs RoHS, The Restriction of Hazardous Substances in Electrical and Electronic Equipment Directive (2002/95/EC) is a European Union legal requirement affecting the global electronics industry. RoHS requirements must be implemented on Lenovo products placed on the market after June 2006. Products on the market before June 2006 are not required to have RoHS compliant parts.
General checkout General checkout This chapter presents the following information: • “What to do first” on page 20 • “Power system checkout” on page 21 Before you go to the checkout, make sure to read the following important notes: Important notes: • Only certified trained personnel can service the computer. • Before replacing any FRU, read the entire page on removing and replacing FRUs. • When you replace FRUs, use new nylon-coated screws.
Lenovo E10-30 Hardware Maintenance Manual What to do first When you do return an FRU, you must include the following information in the parts exchange form or parts return form that you attach to it: 1. Name and phone number of servicer 2. Date of service 3. Date on which the machine failed 4. Date of purchase 5. Procedure index and page number in which the failing FRU was detected 6. Failing FRU name and part number 7. Machine type, model number, and serial number 8.
General checkout Power system checkout To verify a symptom, follow the steps below: 1. Turn off the computer. 2. Remove the battery pack. 3. Connect the AC adapter. 4. Make sure that power is supplied when you turn on the computer. 5. Turn off the computer. 6. Disconnect the AC adapter and install the charged battery pack. 7. Make sure that the battery pack supplies power when you turn on the computer.
Lenovo E10-30 Hardware Maintenance Manual Perform operational charging. If the battery status indicator or icon does not light on, remove the battery pack and let it return to room temperature. Reinstall the battery pack. If the charge indicator or icon is still off, replace the battery pack. If the charge indicator still does not light on, replace the system board. Then reinstall the battery pack. If it is still not charged, go to the next section.
Related service information Related service information This chapter presents the following information: • “Restoring the factory contents by using Recovery Disc Set” on page 23 • “Passwords” on page 24 • “Power management” on page 25 Restoring the factory contents by using Recovery Disc Set When the hard disk drive or solid state drive is replaced because of a failure, no product recovery program is on the new drive. In this case, you must use the Recovery Disc Set for the computer.
Lenovo E10-30 Hardware Maintenance Manual 7. When all of the data has been copied from the last disc in the set, remove the disc and restart the computer. Note: The remainder of the recovery process is fully automated and no action is required by you. The computer will restart into the Windows desktop several times and you might experience periods when no activity is apparent on the screen for several minutes at a time. This is normal. 8.
Related service information Power management Note: Power management modes are not supported for APM operating system. To reduce power consumption, the computer has three power management modes: screen blank, sleep (standby), and hibernation. Screen blank mode If the time set on the “Turn off monitor” timer in the operating system expires, the LCD backlight turns off. You can also turn off the LCD backlight by pressing Fn+F2. To end screen blank mode and resume normal operation, press any key.
Lenovo E10-30 Hardware Maintenance Manual 2. Select Power → Shut down. Putting your computer to sleep If you will be away from your computer for only a short time, put the computer to sleep. When the computer is in sleep mode, you can quickly wake it to resume use, bypassing the startup process. To put the computer to sleep, do one of the following: • Close the display lid. • Press the power button. • Do the proper operations in the operating system. Windows 7: Click Start → Sleep. Windows 8.
Lenovo E10-30 Lenovo E10-30 This chapter presents the following product-specific service references and product-specific parts information: • “Specifications” on page 27 • “Status indicators” on page 29 • “FRU tests” on page 31 • “Fn key combinations” on page 31 • “FRU replacement notices” on page 32 • “Removing and replacing an FRU” on page 33 • “Locations” on page 62 • “Parts list” on page 65 Specifications The following table lists the specifications of the Lenovo E10-30: Table 1.
Lenovo E10-30 Hardware Maintenance Manual Table 1. Specifications (continued) 28 Feature Description I/O port • • • • • Combo audio jack ×1 RJ-45 × 1 2 in 1 slot × 1 (SD / MMC) USB 2.0 × 1, USB 3.0 × 1 VGA × 1 MODEM slot • N/A Audio • Speaker x 2 • Build in Mic x 1 Ethernet (on the system board) • 10/100 M PCI Express Mini Card slot • N/A WWAN • N/A Bluetooth wireless • only support BT&WIFI combo module Integrated camera • 0.3 M / 1.
Lenovo E10-30 Status indicators The system status indicators below show the computer status: a bc 29
Lenovo E10-30 Hardware Maintenance Manual Table 2. Status indicators Indicator Indicator status Meaning On (solid white) The battery has more than 20% charge. Solid amber The battery has between 5% and 20% charge. Fast blinking amber The battery has less than 5% charge. Slow blinking amber The battery is being charged. When battery charge reaches 20%, the blinking color changes to white. Slow blinking white The battery has between 20% and 80% charge and is still charging.
Lenovo E10-30 Fn key combinations The following table shows the function of each combination of Fn with a function key. Table 3. Fn key combinations The following is a brief introduction to the function key combinations. Fn + Pgup: Activates the pause function. Fn + PgDn: Activates the break function. PgUp: Enables/disables the scroll lock. PgDn: Activates the insert function.
Lenovo E10-30 Hardware Maintenance Manual FRU replacement notices This section presents notices related to removing and replacing parts. Read this section carefully before replacing any FRU. Screw notices Loose screws can cause a reliability problem. In the Lenovo computer, this problem is addressed with special nylon-coated screws that have the following characteristics: • They maintain tight connections. • They do not easily come loose, even with shock or vibration. • They are harder to tighten.
Lenovo E10-30 Removing and replacing an FRU This section presents exploded figures with the instructions to indicate how to remove and replace the FRU. Make sure to observe the following general rules: 1. Do not attempt to service any computer unless you have been trained and certified. An untrained person runs the risk of damaging parts. 2. Before replacing any FRU, review “FRU replacement notices” on page 32. 3. Begin by removing any FRUs that have to be removed before the failing FRU.
Lenovo E10-30 Hardware Maintenance Manual 1010 Battery pack DANGER Only use the battery specified in the parts list for your computer. Any other battery could ignite or explode. Figure 1. Removal steps of battery pack Unlock the manual battery latch a. Holding the spring-loaded battery latch in the unlocked position b, remove the battery pack in the direction shown by the arrow c. a c b When installing: Install the battery pack along the slide rails of the slot.
Lenovo E10-30 1020 Dummy card Figure 2. Removal steps of dummy card Remove the dummy card in the direction shown by arrows a b .
Lenovo E10-30 Hardware Maintenance Manual 1030 Keyboard For access, remove this FRU: • “1010 Battery pack” on page 34 Figure 3. Removal steps of keyboard Remove three screws a . a a a Step Screw (quantity) Color Torque a M2 × 1.7 mm, flat-head, nylok-coated (3) Black 1.85+/-0.15 kgfcm 90205495 P/N Loosen the keyboard with fingers in the direction shown by arrow b.
Lenovo E10-30 Figure 3. Removal steps of keyboard (continued) Lift the keyboard a little c , and then detach the connector in the direction shown by arrows d and e.
Lenovo E10-30 Hardware Maintenance Manual 1040 Hard disk drive(HDD)/Memory/Mini PCI Express Card slot compartment cover For access, remove these FRUs in order: • “1010 Battery pack” on page 34 • “1020 Dummy card” on page 35 • “1030 Keyboard” on page 36 Figure 4. Removal steps of hard disk drive(HDD)/Memory/Mini PCI Express Card slot compartment cover Remove seven screws a . a a a a a a a 38 Step Screw (quantity) Color Torque a M2 × 6 mm, flat-head, nylok-coated (7) Black 1.85+/-0.
Lenovo E10-30 Figure 4. Removal steps of hard disk drive(HDD)/Memory/Mini PCI Express Card slot compartment cover (continued) Loosen the screws b that secure the compartment cover. Remove the compartment cover c . b b b b c b b Step Screw (quantity) b M2 × 6 mm, flat-head, Black nylok-coated (6) Color Torque P/N 1.85+/-0.
Lenovo E10-30 Hardware Maintenance Manual 1050 Hard disk drive For access, remove these FRUs in order: • “1010 Battery pack” on page 34 • “1020 Dummy card” on page 35 • “1030 Keyboard” on page 36 • “1040 Hard disk drive(HDD)/Memory/Mini PCI Express Card slot compartment cover” on page 38 Attention: • Do not drop the hard disk drive or apply any physical shock to it. The hard disk drive is sensitive to physical shock. Improper handling can cause damages and permanent loss of data.
Lenovo E10-30 Figure 5. Removal steps of hard disk drive (continued) Remove the hard disk drive in the direction shown by arrow b . b When installing: Make sure that the HDD connector is attached firmly. Remove two screws c and detach the metal frame from the hard disk drive. c c Step Screw (quantity) Color Torque c M3 × 3 mm, flat-head, nylok-coated (2) Black 3.0 +/- 0.
Lenovo E10-30 Hardware Maintenance Manual 1060 PCI Express Mini Card for wireless LAN/WAN For access, remove these FRUs in order: • “1010 Battery pack” on page 34 • “1020 Dummy card” on page 35 • “1030 Keyboard” on page 36 • “1040 Hard disk drive(HDD)/Memory/Mini PCI Express Card slot compartment cover” on page 38 Figure 6. Removal steps of PCI Express Mini Card for wireless LAN/WAN Disconnect the two wireless LAN cables (black, white) a, and then remove the screw b.
Lenovo E10-30 Figure 6. Removal steps of PCI Express Mini Card for wireless LAN/WAN (continued) Remove the card in the direction shown by arrow c . c When installing: • In models with a wireless LAN card that has two antenna connectors, plug the black cable (1st) (MAIN) into the jack labeled 1, and the white cable (2nd) (AUX) into jack labeled 2 on the card.
Lenovo E10-30 Hardware Maintenance Manual 1070 Fan assembly and Heat Sink assembly For access, remove these FRUs in order: • “1010 Battery pack” on page 34 • “1020 Dummy card” on page 35 • “1030 Keyboard” on page 36 • “1040 Hard disk drive(HDD)/Memory/Mini PCI Express Card slot compartment cover” on page 38 • “1050 Hard disk drive” on page 40 • “1060 PCI Express Mini Card for wireless LAN/WAN” on page 42 Figure 7.
Lenovo E10-30 Figure 7. Removal steps of fan assembly and heat sink assembly (continued) b b b Step Screw (quantity) Color Torque P/N b Black 90205491 M2 × 3 mm, flat-head, nylok-coated (3) 1.85+/-0.
Lenovo E10-30 Hardware Maintenance Manual 1080 System board Important notices for handling the system board: When handling the system board, bear the following in mind. • Be careful not to drop the system board on a bench top that has a hard surface, such as metal, wood, or composite. • Avoid rough handling of any kind. • In the whole process, make sure not to drop or stack the system board.
Lenovo E10-30 Figure 8. Removal steps of system board Loosen three screws a . Detach LCD connector in the direction shown by arrow b , USB connector in the direction shown by arrows e and f , unplug power assembly connector in the direction shown by arrow c , RJ 45 port connector in the direction shown by arrow d , speakers connectors in the direction shown by arrow g . a a a Step Screw (quantity) Color Torque a Black M2 × 3 mm, flat-head, nylok-coated (3) 1.85+/-0.
Lenovo E10-30 Hardware Maintenance Manual Figure 8. Removal steps of system board (continued) Detach the touch pad connector in the directions shown by arrows h and i . h i When installing: Make sure that all the connectors are attached firmly. Remove the system board in the direction shown by arrow j .
Lenovo E10-30 1090 LCD unit For access, remove these FRUs in order: • “1010 Battery pack” on page 34 • “1020 Dummy card” on page 35 • “1030 Keyboard” on page 36 • “1040 Hard disk drive(HDD)/Memory/Mini PCI Express Card slot compartment cover” on page 38 • “1050 Hard disk drive” on page 40 • “1060 PCI Express Mini Card for wireless LAN/WAN” on page 42 • “1070 Fan assembly and Heat Sink assembly” on page 44 • “1080 System board” on page 46 Figure 9. Removal steps of LCD unit Remove two screws a .
Lenovo E10-30 Hardware Maintenance Manual Figure 9. Removal steps of LCD unit (continued) Remove the LCD unit in the direction shown by arrow b.
Lenovo E10-30 1100 Base cover, speakers, power assembly and USB board For access, remove these FRUs in order: • “1010 Battery pack” on page 34 • “1020 Dummy card” on page 35 • “1030 Keyboard” on page 36 • “1040 Hard disk drive(HDD)/Memory/Mini PCI Express Card slot compartment cover” on page 38 • “1050 Hard disk drive” on page 40 • “1060 PCI Express Mini Card for wireless LAN/WAN” on page 42 • “1070 Fan assembly and Heat Sink assembly” on page 44 • “1080 System board” on page 46 • “1090 LCD unit” on page 4
Lenovo E10-30 Hardware Maintenance Manual Figure 10. Removal steps of base cover, speakers, power assembly and USB board (continued) Remove the power assembly in the direction shown by arrow c . c When installing: Make sure that the power connector is attached firmly. Remove the screw d . Remove the USB board in the direction shown by arrow e. d e 52 Step Screw (quantity) Color Torque a M2.0 × 3 mm, flat-head, nylok-coated (1) Black 1.85+/-0.
Lenovo E10-30 Note: Applying labels to the base cover The new base cover FRU is shipped with a kit containing labels of several kinds. When you replace the base cover, you need to apply the following label: The following labels need to be peeled off from the old base cover, and need to be put on the new base cover. COA Label Indonesia D Side Label PRC CORD label Bluetooth label Rating Label Rating Label for print WLAN label For some models, you also need to apply one or two FCC labels.
Lenovo E10-30 Hardware Maintenance Manual 1110 LCD front bezel For access, remove these FRUs in order: • “1010 Battery pack” on page 34 • “1020 Dummy card” on page 35 • “1030 Keyboard” on page 36 • “1040 Hard disk drive(HDD)/Memory/Mini PCI Express Card slot compartment cover” on page 38 • “1050 Hard disk drive” on page 40 • “1060 PCI Express Mini Card for wireless LAN/WAN” on page 42 • “1070 Fan assembly and Heat Sink assembly” on page 44 • “1080 System board” on page 46 • “1090 LCD unit” on page 49 • “11
Lenovo E10-30 Figure 11. Removal steps of LCD front bezel (continued) Remove the LCD front bezel in the direction shown by arrows c .
Lenovo E10-30 Hardware Maintenance Manual 1120 LCD panel, LCD cable and hinges For access, remove these FRUs in order: • “1010 Battery pack” on page 34 • “1020 Dummy card” on page 35 • “1030 Keyboard” on page 36 • “1040 Hard disk drive(HDD)/Memory/Mini PCI Express Card slot compartment cover” on page 38 • “1050 Hard disk drive” on page 40 • “1060 PCI Express Mini Card for wireless LAN/WAN” on page 42 • “1070 Fan assembly and Heat Sink assembly” on page 44 • “1080 System board” on page 46 • “1090 LCD unit”
Lenovo E10-30 Figure 12. Removal steps of LCD panel, LCD cable and hinges (continued) Remove six screws c . Lift the LCD hinges in the direction shown by arrows d. c c c c c c 4 4 Step Screw (quantity) d M2.0 × 3 mm, flat-head, nylok-coated (4) Black Color Torque 1.85+/-0.
Lenovo E10-30 Hardware Maintenance Manual Figure 12. Removal steps of LCD panel, LCD cable and hinges (continued) Note: The LCD cables are attached to the LCD panel by a metal connector. Peel off the adhesive tape and detach the connector in the direction shown by arrow e . e When installing: Make sure that the metal connector is attached firmly.
Lenovo E10-30 1130 Integrated camera and power switch board For access, remove these FRUs in order: • “1010 Battery pack” on page 34 • “1020 Dummy card” on page 35 • “1030 Keyboard” on page 36 • “1040 Hard disk drive(HDD)/Memory/Mini PCI Express Card slot compartment cover” on page 38 • “1050 Hard disk drive” on page 40 • “1060 PCI Express Mini Card for wireless LAN/WAN” on page 42 • “1070 Fan assembly and Heat Sink assembly” on page 44 • “1080 System board” on page 46 • “1090 LCD unit” on page 49 • “1100
Lenovo E10-30 Hardware Maintenance Manual Figure 13. Removal steps of integrated camera and power switch board (continued) Unplug the power switch board connector in the direction shown by arrow a . Remove the power switch board from the LCD cover b .
Lenovo E10-30 1140 Antenna assembly and LCD cover For access, remove these FRUs in order: • “1010 Battery pack” on page 34 • “1020 Dummy card” on page 35 • “1030 Keyboard” on page 36 • “1040 Hard disk drive(HDD)/Memory/Mini PCI Express Card slot compartment cover” on page 38 • “1050 Hard disk drive” on page 40 • “1060 PCI Express Mini Card for wireless LAN/WAN” on page 42 • “1070 Fan assembly and Heat Sink assembly” on page 44 • “1080 System board” on page 46 • “1090 LCD unit” on page 49 • “1100 Base cover
Lenovo E10-30 Hardware Maintenance Manual Locations Front view a b c d e f g h i j Integrated camera Wireless antennas Display Novo button Power button Built-in microphone System indicators Touch pad Touch pad buttons Memory card slot a b c d e f g j h i 62
Lenovo E10-30 Right-side view a USB port b RJ-45 port b a 63
Lenovo E10-30 Hardware Maintenance Manual Bottom and Left-side view a b c d e f g h i j AC power adapter jack VGA port Ventilation slots USB 3.
Lenovo E10-30 Parts list This section presents the following service parts: • “Overall” on page 66 • “LCD FRUs” on page 70 • “Keyboard” on page 72 • “Miscellaneous parts” on page 76 • “AC adapters” on page 77 • “Power cords” on page 78 Notes: • Each FRU is available for all types or models, unless specific types or models are specified.
Lenovo E10-30 Hardware Maintenance Manual Overall 1 2 3 c 4 b 5 8 6 7 10 9 11 12 13 15 d a 14 16 66
Lenovo E10-30 Table 4. Parts list—Overall No. FRU 1 2 3 3 4 LCD unit (see “LCD FRUs” on page 70.) Keyboard (see “Keyboard” on page 72.) E10-30 Upper Case BK E10-30 Upper Case White WirelessLan_Intel, Intel 3160 1x1AC+BT PCIE NGFF WLAN, INTEL 3160 1X1 AC+BT4.0, Intel 1x1 AC wifi+ BT4.0 Combo(support WIDI) WirelessLan_Non_Intel, Ltn HFA335 1x1BN+BT4.0 PCIE M.2 WLAN, NON-INTEL 1X1 BGN+BT4.0, WiFi 1x1 BGN+BT4.0 Combo WirelessLan_Non_Intel, Cbt BCM43142 1x1BN+BT4.0 PCIE M.2 WLAN, NON-INTEL 1X1 BGN+BT4.
Lenovo E10-30 Hardware Maintenance Manual Table 4. Parts list—Overall (continued) No. FRU FRU no. 8 Battery S100 SMP/S L10M3Z11 3S1P 24Wh white Bty 3CELL 24WH Battery S100 Celx/L L10C3Z11 3S1P 24Wh whiteBty 3CELL 24WH Battery S100 SMP/S L10M6Y12 3S2P 48Wh white Bty 6CELL 48WH Battery S100 Celx/L L10C6Y12 3S2P 48Wh whiteBty 6CELL 48WH Battery S100 SP/S L10M3Z11 11.1V24Wh 3cellBty EU 3CELL 24WH Battery S100 Celx/L L10C3Z11 3S1P 24Wh blackBty 3CELL 24WH 3 cell 2200 Ah Battery S100 SP/S L10M6Y12 11.
Lenovo E10-30 Table 4. Parts list—Overall (continued) No. FRU FRU no. CRU ID 14 HDD, TSB MQ01ABF032 6G 7mm 5.4K 320G HDD 320G 5400rpm HDD, WD3200LPCX-24C6HT0 6G 7mm 5.4K 320G HDD 320G 5400rpm HDD, HTS545032A7E660 6G 7mm 5.4K 320G HDD 320G 5400rpm HDD, ST500LT012 6G 7mm 5.4K 500G HDD 500G 5400rpm HDD, WD5000LPCX-24C6HT0 6G 7mm 5.4K 500G HDD 500G 5400rpm HDD, TSB MQ01ABF050 6G 7mm 5.4K 500G HDD 500G 5400rpm HDD, HTS545050A7E660 6G 7mm 5.4K 500G HDD 500G 5400rpm HDD, ST500LM012 6G 9.5mm 5.
Lenovo E10-30 Hardware Maintenance Manual LCD FRUs In Lenovo E10-30, there are following types of LCDs. • “10.1-in.
Lenovo E10-30 10.1-in. HD TFT (E10-30) Table 5. Parts list—10.1-in. HD TFT No. FRU FRU no. CRU ID 1 1 2 3 E10-30 LCD Bezel BK E10-30 LCD Bezel White LCD Bezel Screw Pad Panel, IVO M101NWN8 R0 HD AG F LED1 NB LCD, 10.1 HD LED ANTI-GLARE, 10.1" Panel 16:9, TN, 1366*768 Panel, AUO B101XTN01.1 1A HD AG F LED1 NB LCD, 10.1 HD LED ANTI-GLARE, 10.1" Panel 16:9, TN, 1366*768 Panel, CMI N101BGE L31 HD AG F LED1 NB LCD, 10.1 HD LED ANTI-GLARE, 10.
Lenovo E10-30 Hardware Maintenance Manual Keyboard Table 6. Parts list—Keyboard Language E10-30 72 Chicony (Black) P/N English U.K.
Lenovo E10-30 Table 6. Parts list—Keyboard Language E10-30 Sunrex (continued) (Black) P/N English U.K.
Lenovo E10-30 Hardware Maintenance Manual Table 6. Parts list—Keyboard Language Chicony E10-30 (continued) (White) 74 P/N English U.K.
Lenovo E10-30 Table 6. Parts list—Keyboard Language E10-30 Sunrex (continued) (White) P/N English U.K.
Lenovo E10-30 Hardware Maintenance Manual Miscellaneous parts Table 7. Parts list—Miscellaneous parts FRU System miscellaneous parts: • (a) E10-30 HDD Bracket • (b) E10-30 Touchpad Bracket Cable miscellaneous parts: • (c) E10-30 Touchpad Module • (d) E10-30 USB Cable P/N CRU ID N 90205453 90205461 N 90205456 90205455 Note: Italicized letters in parentheses are references to the exploded view in “Overall” on page 71. Screw Table 8. Parts list—screws FRU P/N E10-30 Screw φ4×H0.
Lenovo E10-30 AC adapters Table 9. Parts list—3-pin AC adapters FRU P/N CRU ID 45W(3pin), Delta ADLX45NDC3A 20V2.25A adapter Delta BLACK 45W(3pin), Liteon ADLX45NLC3A 20V2.25A adapter Liteon BLACK 45W(3pin), Chicony ADLX45NCC3A 20V2.
Lenovo E10-30 Hardware Maintenance Manual Power cords A Lenovo power cord for a specific country or region is usually available only in that country or region: Table 10.
Lenovo E10-30 Table 10.
Lenovo E10-30 Hardware Maintenance Manual Table 10.
Notices Notices Lenovo may not offer the products, services, or features discussed in this document in all countries. Consult your local Lenovo representative for information on the products and services currently available in your area. Any reference to a Lenovo product, program, or service is not intended to state or imply that only that Lenovo product, program, or service may be used.
Lenovo E10-30 Hardware Maintenance Manual Notices Any performance data contained herein was determined in a controlled environment. Therefore, the result obtained in other operating environments may vary significantly. Some measurements may have been made on development-level systems and there is no guarantee that these measurements will be the same on generally available systems. Furthermore, some measurements may have been estimated through extrapolation. Actual results may vary.
