IdeaPad S10-3s Hardware Maintenance Manual
Note: Before using this information and the product it supports, be sure to read the general information under “Notices” on page 76. First Edition (March 2010) © Copyright Lenovo 2010. All rights reserved. LENOVO products, data, computer software, and services have been developed exclusively at private expense and are sold to governmental entities as commercial items as defined by 48 C.F.R. 2.101 with limited and restricted rights to use, reproduction and disclosure.
Contents About this manual........................................ iv Safety information......................................... 1 General safety................................................. 2 Electrical safety............................................... 3 Safety inspection guide................................... 5 Handling devices that are sensitive to electrostatic discharge..................................... 6 Grounding requirements..................................
About this manual This manual contains service and reference information for the following Lenovo IdeaPad product: Lenovo IdeaPad S10-3s Use this manual to troubleshoot problems. The manual is divided into the following sections: •• The common sections provide general information, guidelines, and safety information required for servicing computers. •• The product-specific section includes service, reference, and product-specific parts information.
Safety information Safety information This chapter presents the following safety information that you need to get familiar with before you service an IdeaPad S10-3s computer: •• “General safety” on page 2 •• “Electrical safety” on page 3 •• “Safety inspection guide” on page 5 •• “Handling devices that are sensitive to electrostatic discharge” on page 6 •• “Grounding requirements” on page 6 •• “Safety notices: multilingual translations” on page 7 •• “Laser compliance statement” on page 14 1
IdeaPad S10-3s Hardware Maintenance Manual General safety Follow these rules below to ensure general safety: •• Observe a good housekeeping in the area where the machines are put during and after the maintenance. •• When lifting any heavy object: 1. Make sure that you can stand safely without slipping. 2. Distribute the weight of the object equally between your feet. 3. Use a slow lifting force. Never move suddenly or twist when you attempt to lift it. 4.
Safety information Electrical safety Observe the following rules when working on electrical equipments. Important: Use only approved tools and test equipments. Some hand tools have handles covered with a soft material that does not insulate you when working with live electrical currents. Many customers have rubber floor mats near their machines that contain small conductive fibers to decrease electrostatic discharges. Do not use such kind of mat to protect yourself from electrical shock.
IdeaPad S10-3s Hardware Maintenance Manual •• Always look carefully for possible hazards in your work area. Examples of these hazards are moist floors, nongrounded power extension cables, power surges, and missing safety grounds. •• Do not touch live electrical circuits with the reflective surface of a plastic dental mirror. The surface is conductive; such touching can cause personal injury and machine damage.
Safety information Safety inspection guide The purpose of this inspection guide is to assist you in identifying potential unsafe conditions. As each machine was designed and built, required safety items were installed to protect users and service personnel from injury. This guide addresses only those items. You should use good judgment to identify potential safety hazards according to the attachment of non-Lenovo IdeaPad features or options not covered by this inspection guide.
IdeaPad S10-3s Hardware Maintenance Manual Handling devices that are sensitive to electrostatic discharge Any computer part containing transistors or integrated circuits (ICs) should be considered sensitive to electrostatic discharge (ESD). ESD damage can occur when there is a difference in charge between objects. Protect against ESD damage by equalizing the charge so that the machine, the part, the work mat, and the person handling the part are all at the same charge. Notes: 1.
Safety information Safety notices: multilingual translations The safety notices in this section are provided in English, French, German, Hebrew, Italian, Japanese, and Spanish. Safety notice 1 Before the computer is powered on after FRU replacement, make sure all screws, springs, and other small parts are in place and are not left loose inside the computer. Verify this by shaking the computer and listening for rattling sounds. Metallic parts or metal flakes can cause electrical shorts.
IdeaPad S10-3s Hardware Maintenance Manual Safety notice 2 DANGER Some standby batteries contain a small amount of nickel and cadmium. Do not disassemble a standby battery, recharge it, throw it into fire or water, or shortcircuit it. Dispose of the battery as required by local ordinances or regulations. Use only the battery in the appropriate parts listing. Use of an incorrect battery can result in ignition or explosion of the battery. Certaines batteries de secours contiennent du nickel et du cadmium.
Safety information Safety notice 3 DANGER The battery pack contains small amounts of nickel. Do not disassemble it, throw it into fire or water, or short-circuit it. Dispose of the battery pack as required by local ordinances or regulations. Use only the battery in the appropriate parts listing when replacing the battery pack. Use of an incorrect battery can result in ignition or explosion of the battery. La batterie contient du nickel. Ne la démontez pas, ne l’exposez ni au feu ni à l’eau.
IdeaPad S10-3s Hardware Maintenance Manual Safety notice 4 DANGER The lithium battery can cause a fire, an explosion, or a severe burn. Do not recharge it, remove its polarized connector, disassemble it, heat it above 100°C (212°F), incinerate it, or expose its cell contents to water. Dispose of the battery as required by local ordinances or regulations. Use only the battery in the appropriate parts listing. Use of an incorrect battery can result in ignition or explosion of the battery.
Safety information Safety notice 5 If the LCD breaks and the fluid from inside the LCD gets into your eyes or on your hands, immediately wash the affected areas with water at least for 15 minutes. Seek medical care if any symptoms caused by the fluid are present after washing. Si le panneau d’affichage à cristaux liquides se brise et que vous recevez dans les yeux ou sur les mains une partie du fluide, rincez-les abondamment pendant au moins quinze minutes.
IdeaPad S10-3s Hardware Maintenance Manual Safety notice 6 DANGER To avoid shock, do not remove the plastic cover that protects the lower part of the inverter card. Afin d’éviter tout risque de choc électrique, ne retirez pas le cache en plastique protégeant la partie inférieure de la carte d’alimentation. Aus Sicherheitsgründen die Kunststoffabdeckung, die den unteren Teil der Spannungswandlerplatine umgibt, nicht entfernen.
Safety information Safety notice 8 DANGER Before removing any FRU, turn off the computer, unplug all power cords from electrical outlets, remove the battery pack, and then disconnect any interconnecting cables. Avant de retirer une unité remplaçable en clientèle, mettez le système hors tension, débranchez tous les cordons d’alimentation des socles de prise de courant, retirez la batterie et déconnectez tous les cordons d’interface.
IdeaPad S10-3s Hardware Maintenance Manual Laser compliance statement Some models of Lenovo IdeaPad computer are equipped from the factory with an optical storage device such as a CD-ROM drive or a DVD-ROM drive. Such devices are also sold separately as options. If one of these drives is installed, it is certified in the U.S. to conform to the requirements of the Department of Health and Human Services 21 Code of Federal Regulations (DHHS 21 CFR) Subchapter J for Class 1 laser products.
Safety information A CD-ROM drive, a DVD-ROM drive, or any other storage device installed may contain an embedded Class 3A or Class 3B laser diode. Note the following: DANGER Emits visible and invisible laser radiation when open. Do not stare into the beam, do not view directly with optical instruments, and avoid direct exposure to the beam. Radiação por raio laser ao abrir. Não olhe fixo no feixe de luz, não olhe diretamente por meio de instrumentos óticos e evite exposição direta com o feixe de luz.
IdeaPad S10-3s Hardware Maintenance Manual Important service information This chapter presents the following important service information: •• “Strategy for replacing FRUs” on page 16 – “Strategy for replacing a hard disk drive” on page 17 – “Important notice for replacing a system board ” on page 17 •• “Important information about replacing RoHS compliant FRUs” on page 18 Important: BIOS and device driver fixes are customer-installable.
Important service information Use the following strategy to prevent unnecessary expense for replacing and servicing FRUs: •• If you are instructed to replace an FRU, but the replacement does not solve the problem, reinstall the original FRU before you continue. •• Some computers have both a processor board and a system board. If you are instructed to replace either of them, and replacing one of them does not solve the problem, reinstall that board, and then replace the other one.
IdeaPad S10-3s Hardware Maintenance Manual Important information about replacing RoHS compliant FRUs RoHS, The Restriction of Hazardous Substances in Electrical and Electronic Equipment Directive (2002/95/EC) is a European Union legal requirement affecting the global electronics industry. RoHS requirements must be implemented on Lenovo products placed on the market after June 2006. Products on the market before June 2006 are not required to have RoHS compliant parts.
General checkout General checkout This chapter presents the following information: •• “What to do first” on page 20 •• “Power system checkout” on page 21 Before you go to the checkout, make sure to read the following important notes: Important notes: • Only certified trained personnel can service the computer. • Before replacing any FRU, read the entire page on removing and replacing FRUs. • When you replace FRUs, use new nylon-coated screws.
IdeaPad S10-3s Hardware Maintenance Manual What to do first When you do return an FRU, you must include the following information in the parts exchange form or parts return form that you attach to it: 1. Name and phone number of servicer 2. Date of service 3. Date on which the machine failed 4. Date of purchase 5. Procedure index and page number in which the failing FRU was detected 6. Failing FRU name and part number 7. Machine type, model number, and serial number 8.
General checkout Power system checkout To verify a symptom, follow the steps below: 1. Turn off the computer. 2. Remove the battery pack. 3. Connect the AC adapter. 4. Make sure that power is supplied when you turn on the computer. 5. Turn off the computer. 6. Disconnect the AC adapter and install the charged battery pack. 7. Make sure that the battery pack supplies power when you turn on the computer.
IdeaPad S10-3s Hardware Maintenance Manual Perform operational charging. If the battery status indicator or icon does not light on, remove the battery pack and let it return to room temperature. Reinstall the battery pack. If the charge indicator or icon is still off, replace the battery pack. If the charge indicator still does not light on, replace the system board. Then reinstall the battery pack. If it is still not charged, go to the next section.
Related service information Related service information This chapter presents the following information: •• “Restoring the factory contents by using OneKey Recovery” on page 23 •• “Passwords” on page 24 •• “Power management” on page 25 Restoring the factory contents by using OneKey Recovery Restore of factory default The IdeaPad S10-3s computers come with pre-installed OneKey Rescue System.
IdeaPad S10-3s Hardware Maintenance Manual When you use the recovery discs to boot your computer, the system will enter the user interface for system recovery automatically. Please follow the prompt to insert the backup discs to complete the whole recovery process. Note: The recovery process might take up to 2 hours. Passwords As many as two passwords may be needed for any Lenovo IdeaPad computer: the power-on password (POP) and the supervisor password (SVP).
Related service information Power management Note: Power management modes are not supported for APM operating system. To reduce power consumption, the computer has three power management modes: screen blank, sleep (standby), and hibernation. Screen blank mode If the time set on the “Turn off monitor” timer in the operating system expires, the LCD backlight turns off. You can also turn off the LCD backlight by pressing Fn+F2. To end screen blank mode and resume normal operation, press any key.
IdeaPad S10-3s Hardware Maintenance Manual Hibernation mode In hibernation mode, the following occurs: •• The system status, RAM, VRAM, and setup data are stored on the hard disk. •• The system is powered off. To cause the computer to enter hibernation mode, follow the steps below: •• If you are using the ACPI operating system and have defined one of the following actions as the event that causes the system to go into hibernation mode, perform that action: – Closing the lid. – Pressing the power button.
Lenovo IdeaPad S10-3s Lenovo IdeaPad S10-3s This chapter presents the following product-specific service references and product-specific parts information: •• “Specifications” on page 27 •• “Status indicators” on page 29 •• “Fn key combinations” on page 31 •• “FRU replacement notices” on page 32 •• “Removing and replacing an FRU” on page 33 •• “Locations” on page 60 •• “Parts list” on page 62 Specifications The following table lists the specifications of the Lenovo IdeaPad S10-3s : Table 1.
IdeaPad S10-3s Hardware Maintenance Manual Table 1. Specifications (continued) Feature Description I/O port • • • • • • • • • • • MODEM slot Audio Video Ethernet (on the system board) PCI Express Mini Card slot WLAN Bluetooth wireless SSD Keyboard Touch pad Integrated camera Battery AC adapter Pre-installed operating system 28 External monitor connector Stereo headphone jack Microphone jack RJ45 x 1 (on planar) USB2.
Lenovo IdeaPad S10-3s Status indicators The system status indicators below show the computer status: 1 2 3 4 5 Table 2. Status indicators Indicator 1 Caps lock 2 Power on Meaning White: Caps Lock mode is enabled. You can enter all alphabetic characters (A-Z) in uppercase without pressing the Shift key. To enable or disable Caps Lock mode, press the CapsLk key. White: System is enabled. Blinking white: System is in sleep mode. Off: System is in hibernate mode or shut down.
IdeaPad S10-3s Hardware Maintenance Manual Table 2. Status indicators (continued) Indicator 30 3 Battery status 4 Wireless status 5 Drive in use Meaning Blinking amber: (500ms off/1s on) The remaining power of the battery is less than 5% of its capacity. Blinking amber: (100ms off/3.2s on) The battery is being charged with the remaining power between 5% and 20% of its capacity. Amber: The computer is operating on battery power with the remaining power between 5% and 20% of its capacity.
Lenovo IdeaPad S10-3s Fn key combinations The following table shows the function of each combination of Fn with a function key. Table 4. Fn key combinations Key combination Description Fn + Esc: Fn + F1: Fn + F2: Turn on/off the integrated camera. Enter sleep mode. Turn on/off the LCD screen. Open the interface for the display device switch to select notebook or external display. Open the interface for integrated wireless devices settings (enable/disable). Enable/Disable the touchpad.
IdeaPad S10-3s Hardware Maintenance Manual FRU replacement notices This section presents notices related to removing and replacing parts. Read this section carefully before replacing any FRU. Screw notices Loose screws can cause a reliability problem. In the Lenovo IdeaPad computer, this problem is addressed with special nylon-coated screws that have the following characteristics: •• They maintain tight connections. •• They do not easily come loose, even with shock or vibration.
Lenovo IdeaPad S10-3s Removing and replacing an FRU This section presents exploded figures with the instructions to indicate how to remove and replace the FRU. Make sure to observe the following general rules: 1. Do not attempt to service any computer unless you have been trained and certified. An untrained person runs the risk of damaging parts. 2. Before replacing any FRU, review “FRU replacement notices” on page 32. 3. Begin by removing any FRUs that have to be removed before the failing FRU.
IdeaPad S10-3s Hardware Maintenance Manual 1010 Battery pack DANGER Only use the battery specified in the parts list for your computer. Any other battery could ignite or explode. Figure 1. Removal steps of battery pack Unlock the battery release lever 1. Holding the battery release lever in the unlocked position 2, remove the battery pack in the direction shown by arrow 3. 2 3 2 1 1 When installing: Install the battery pack along the slide rails of the slot.
Lenovo IdeaPad S10-3s 1020 Dummy cards For access, remove this FRU: •• “1010 Battery pack” on page 34 Figure 2. Removal steps of dummy cards Remove two dummy cards in the direction shown by arrows 1 2.
IdeaPad S10-3s Hardware Maintenance Manual 1030 SIM card For access, remove this FRU: •• “1010 Battery pack” on page 34 Figure 3. Removal steps of SIM card Open the SIM card slot cover in the direction shown by arrow 1, push the SIM card in until you hear a click, and then pull the SIM card out in the direction shown by arrow 2.
Lenovo IdeaPad S10-3s 1040 Keyboard For access, remove this FRU: •• “1010 Battery pack” on page 34 Figure 4. Removal steps of keyboard Remove three screws 1. 1 1 1 Step 1 Screw (quantity) Color Torque M2 × 2 mm, flat-head, nylok-coated (3) Black 1.
IdeaPad S10-3s Hardware Maintenance Manual Figure 4. Removal steps of keyboard (continued) Lift the keyboard a little, detach the connector in the direction shown by arrows 2 3, and then remove the keyboard 4. 4 2 3 When installing: Make sure that the FPC connector is attached firmly.
Lenovo IdeaPad S10-3s 1050 Base cover For access, remove these FRUs in order: •• “1010 Battery pack” on page 34 •• “1040 Keyboard” on page 37 Figure 5. Removal steps of base cover Remove one screw 1 and four screws 2. 2 2 1 2 2 Step 1 2 Screw (quantity) Color Torque M2 × 2 mm, flat-head, nylok-coated (1) Black 1.6 kgfcm M2 × 8 mm, flat-head, nylok-coated (4) White 1.
IdeaPad S10-3s Hardware Maintenance Manual Figure 5. Removal steps of base cover (continued) Remove two screws 3 and four screws 4 on the bottom. Remove the base cover in the direction shown by arrow 5. 3 4 3 4 4 5 Step 3 4 40 4 Screw (quantity) Color Torque M2 × 8 mm, flat-head, nylok-coated (2) White 1.6 kgfcm M2 × 5 mm, flat-head, nylok-coated (4) White 1.
Lenovo IdeaPad S10-3s Note: Applying labels to the base cover The new base cover FRU is shipped with a kit containing labels of several kinds. When you replace the base cover, you need to apply the following label: The following labels need to be peeled off from the old base cover, and need to be put on the new base cover. a Wistron Label b LAN ID Label c COA Label d PRC/MTM Label e Rating Label f Wireless Label g Bluetooth Label h ECC Label For some models, you also need to apply one or two FCC labels.
IdeaPad S10-3s Hardware Maintenance Manual 1060 PCI Express Mini Card for wireless LAN For access, remove these FRUs in order: •• “1010 Battery pack” on page 34 •• “1020 Dummy cards” on page 35 •• “1040 Keyboard” on page 37 •• “1050 Base cover” on page 39 Figure 6. Removal steps of PCI Express Mini Card for wireless LAN 2 1 Disconnect the two wireless LAN cables (black, white) 1, and then remove the screw 2.
Lenovo IdeaPad S10-3s Figure 6. Removal steps of PCI Express Mini Card for wireless LAN (continued) Remove the card in the direction shown by arrow 3. 3 When installing: •• In models with a wireless LAN card that has two antenna connectors, plug the black cable (1st) (MAIN) into the jack labeled 1, and the white cable (2nd) (AUX) into jack labeled 2 on the card.
IdeaPad S10-3s Hardware Maintenance Manual 1070 LCD unit For access, remove these FRUs in order: •• “1010 Battery pack” on page 34 •• “1020 Dummy cards” on page 35 •• “1040 Keyboard” on page 37 •• “1050 Base cover” on page 39 •• “1060 PCI Express Mini Card for wireless LAN” on page 42 Figure 7. Removal steps of LCD unit Remove two connectors 1 and release the LCD cable and antenna cables from the cable guides 2. 2 2 2 2 1 1 Remove two srews 3.
Lenovo IdeaPad S10-3s Figure 7. Removal steps of LCD unit (continued) Swing the LCD hinges in the direction shown by arrows 4. 4 4 Remove the LCD unit in the direction shown by arrow 5.
IdeaPad S10-3s Hardware Maintenance Manual 1080 Hard disk drive (HDD) For access, remove these FRUs in order: •• “1010 Battery pack” on page 34 •• “1020 Dummy cards” on page 35 •• “1040 Keyboard” on page 37 •• “1050 Base cover” on page 39 •• “1060 PCI Express Mini Card for wireless LAN” on page 42 •• “1070 LCD unit” on page 44 Attention: • Do not drop the hard disk drive or apply any physical shock to it. The hard disk drive is sensitive to physical shock.
Lenovo IdeaPad S10-3s 1090 DIMM For access, remove these FRUs in order: •• “1010 Battery pack” on page 34 •• “1020 Dummy cards” on page 35 •• “1040 Keyboard” on page 37 •• “1050 Base cover” on page 39 Figure 9. Removal steps of DIMM Release the two latches on both edges of the socket at the same time in the direction shown by arrows 1, and then unplug the DIMM in the direction shown by arrow 2.
IdeaPad S10-3s Hardware Maintenance Manual 1100 Fan assembly For access, remove this FRU: •• “1010 Battery pack” on page 34 •• “1020 Dummy cards” on page 35 •• “1040 Keyboard” on page 37 •• “1050 Base cover” on page 39 Figure 10. Removal steps of fan assembly Note: Remove two screws 1 and detach one connector in the direction shown by arrow 2. 1 1 2 When installing: Make sure that the fan connector is attached firmly to the system board. Step 1 48 Screw (quantity) Color Torque M2 × 3.
Lenovo IdeaPad S10-3s Figure 10. Removal steps of fan assembly (continued) Lift the fan assembly in the direction shown by arrow damage the connector. 3.
IdeaPad S10-3s Hardware Maintenance Manual 1110 System board Important notices for handling the system board: When handling the system board, bear the following in mind. • Be careful not to drop the system board on a bench top that has a hard surface, such as metal, wood, or composite. • Avoid rough handling of any kind. • In the whole process, make sure not to drop or stack the system board.
Lenovo IdeaPad S10-3s Figure 11. Removal steps of system board Remove five screws 1, detach three connectors in the direction shown by arrows 2 3 4. 1 1 1 1 1 2 3 2 4 When installing: Make sure that the three connectors are attached firmly. Step 1 Screw (quantity) Color Torque M2 × 3.5 mm, flat-head, nylok-coated (5) Black 1.6 kgfcm Remove the system board in the direction shown by arrow 5.
IdeaPad S10-3s Hardware Maintenance Manual 1120 Speakers For access, remove these FRUs in order: •• “1010 Battery pack” on page 34 •• “1020 Dummy cards” on page 35 •• “1040 Keyboard” on page 37 •• “1050 Base cover” on page 39 •• “1060 PCI Express Mini Card for wireless LAN” on page 42 •• “1070 LCD unit” on page 44 •• “1080 Hard disk drive (HDD)” on page 46 •• “1090 DIMM” on page 47 •• “1100 Fan assembly” on page 48 •• “1110 System board” on page 50 Figure 12.
Lenovo IdeaPad S10-3s 1130 Bluetooth card For access, remove these FRUs in order: •• “1010 Battery pack” on page 34 •• “1020 Dummy cards” on page 35 •• “1040 Keyboard” on page 37 •• “1050 Base cover” on page 39 •• “1060 PCI Express Mini Card for wireless LAN” on page 42 •• “1070 LCD unit” on page 44 •• “1080 Hard disk drive (HDD)” on page 46 •• “1090 DIMM” on page 47 •• “1100 Fan assembly” on page 48 •• “1110 System board” on page 50 Figure 13.
IdeaPad S10-3s Hardware Maintenance Manual 1140 LCD front bezel For access, remove these FRUs in order: •• “1010 Battery pack” on page 34 •• “1020 Dummy cards” on page 35 •• “1040 Keyboard” on page 37 •• “1050 Base cover” on page 39 •• “1060 PCI Express Mini Card for wireless LAN” on page 42 •• “1070 LCD unit” on page 44 Figure 14. Removal steps of LCD front bezel Remove four screws 1. 1 1 1 1 Step 1 Screw (quantity) Color Torque M2 × 3.5 mm, flat-head, nylok-coated (4) Black 1.
Lenovo IdeaPad S10-3s 1150 LCD panel, LCD cable and hinges For access, remove these FRUs in order: •• “1010 Battery pack” on page 34 •• “1020 Dummy cards” on page 35 •• “1040 Keyboard” on page 37 •• “1050 Base cover” on page 39 •• “1060 PCI Express Mini Card for wireless LAN” on page 42 •• “1070 LCD unit” on page 44 •• “1140 LCD front bezel” on page 54 Figure 15.
IdeaPad S10-3s Hardware Maintenance Manual Figure 15. Removal steps of LCD panel, LCD cable and hinges (continued) Remove four screws 4 and then release the hinges in the direction shown by arrows 5. 4 4 4 5 4 5 Step 4 Screw (quantity) Color Torque M2 × 3.5 mm, flat-head, nylok-coated (4) Black 1.6 kgfcm Note: The LCD cables are attached to the LCD panel by a metal connector. Peel off the adhesive tape and detach the metal connector in the direction shown by arrow 6.
Lenovo IdeaPad S10-3s 1160 Integrated camera For access, remove these FRUs in order: •• “1010 Battery pack” on page 34 •• “1020 Dummy cards” on page 35 •• “1040 Keyboard” on page 37 •• “1050 Base cover” on page 39 •• “1060 PCI Express Mini Card for wireless LAN” on page 42 •• “1070 LCD unit” on page 44 •• “1140 LCD front bezel” on page 54 •• “1150 LCD panel, LCD cable and hinges” on page 55 Figure 16.
IdeaPad S10-3s Hardware Maintenance Manual 1170 Antenna assembly and LCD cover For access, remove these FRUs in order: •• “1010 Battery pack” on page 34 •• “1020 Dummy cards” on page 35 •• “1040 Keyboard” on page 37 •• “1050 Base cover” on page 39 •• “1060 PCI Express Mini Card for wireless LAN” on page 42 •• “1070 LCD unit” on page 44 •• “1140 LCD front bezel” on page 54 •• “1150 LCD panel, LCD cable and hinges” on page 55 Figure 17.
Lenovo IdeaPad S10-3s Figure 17. Removal steps of antenna assembly and LCD cover (continued) Peel off the adhesive tapes securing the antenna boards, release the cables from the cable guide, and then remove the antenna assembly in the direction shown by arrows 3. 3 3 When installing: Route the antenna cables along the cable guides and secure the antenna boards with adhesive tapes. As you route the cables, make sure that they are not subjected to any tension.
IdeaPad S10-3s Hardware Maintenance Manual Locations Front view Integrated camera Array microphones (bulit-in) Wireless LAN antennas System status indicators Note: For the description of each indicator, see “Status indicators” on page 29.
Lenovo IdeaPad S10-3s Right-side view 1 2 3 4 5 6 Integrated wireless device switch Headphone jack Microphone jack USB port RJ-45 port Lanyard hole 6 1 2 3 4 5 Bottom and Left-side view 1 2 3 4 5 6 7 8 9 J Memory card slot USB port Fan louvers VGA port AC power adapter jack Battery latch - manual SIM card slot (selected models only) Battery pack Battery latch - spring loaded Speakers 9 8 7 6 5 10 4 3 10 1 2 61
IdeaPad S10-3s Hardware Maintenance Manual Parts list This section presents the following service parts: •• “Overall” on page 63 •• “LCD FRUs” on page 67 •• “Keyboard” on page 69 •• “Miscellaneous parts” on page 72 •• “AC adapters” on page 73 •• “Power cords” on page 74 Notes: • Each FRU is available for all types or models, unless specific types or models are specified.
Lenovo IdeaPad S10-3s Overall 1 2 3 c a 4 5 d 6 7 8 9 10 11 b e 12 13 14 15 63
IdeaPad S10-3s Hardware Maintenance Manual Table 5. Parts list—Overall No. FRU 1 2 3 4 4 5 5 6 6 7 8 8 8 8 8 8 LCD unit (see “LCD FRUs” on page 67.) Keyboard (see “Keyboard” on page 69.) LM30 TOUCHPAD W/COVER HAIBO LM30 Upper CASE WHITE IMF HAIBO LM30 Upper CASE WHITE IMF WIND CPU, Intel Pineview N450 1.66G A-0 BGA processor CPU, Intel Pineview N470 1.83G A-0 BGA processor LM30 MB N450 1.66G W/OD DA 09298-1 LM30 MB N470 1.83G W/OD DA 09298-1 LM30 IO BD 09714-1 SVT (D) WLAN card, 802.
Lenovo IdeaPad S10-3s Table 5. Parts list—Overall (continued) No. FRU FRU no.
IdeaPad S10-3s Hardware Maintenance Manual Table 5. Parts list—Overall (continued) No. FRU FRU no. 13 Battery pack, 3 cell Battery 2.2Ah, M3 Sanyo L09S3Z14 3S1P 24Wh Li-ion (white) Battery pack, 6 cell Battery 2.2Ah, M3 Sanyo L09S6Y14 3S2P 48Wh Li-ion (white) Battery pack, 3 cell Battery 2.2Ah, M3 SMP L09M3Z14 3S1P 24Wh Li-ion (white) Battery pack, 6 cell Battery 2.2Ah, M3 SMP L09M6Y14 3S2P 48Wh Li-ion (white) Battery pack, 3 cell Battery 2.
Lenovo IdeaPad S10-3s LCD FRUs In Lenovo IdeaPad S10-3s, there are following types of LCDs. •• “10.1-in.
IdeaPad S10-3s Hardware Maintenance Manual 10.1-in. WXGA TFT Table 6. Parts list—10.1-in. WXGA TFT No. FRU 1 2 3 3 3 3 LM30 LCD_BEZEL_ASSY 31043211 LM30 HINGE PACK L/R 31043218 LCD panel, 1024*600 10.1"(Flat type), B101AW02 V0 18004001 LCD panel, 1024*600 10.1"(Flat type), CLAA101NB03A 18003997 LCD panel, 1024*600 10.1"(Flat type), N101L6-L0D 18003998 LCD panel, 1280*720 10.1"(Flat type), AUO B101EW01 V0 18004005 SD+ G LED1 NB LM30 C.A.
Lenovo IdeaPad S10-3s Keyboard Table 7. Parts list—Keyboard Language P/N Chicony Keyboard (white) ALPS Japanese International English Swiss Slovenian Slovak Icelandic Belgian Four Nordic countries Hungarian Hebrew Greek Dutch Czech Brazilian Arabic German French Russian Traditional Chinese Korean Canadian English&French Latin Portuguese Thai Turkish Spanish Italian U.K.
IdeaPad S10-3s Hardware Maintenance Manual Table 7. Parts list—Keyboard (continued) Language Keyboard (white) (continued) Keyboard (black) 70 P/N Sunrex (continued) Chicony Arabic German French Russian Traditional Chinese Korean Canadian English&French Latin Portuguese Thai Turkish Spanish Italian U.K. English English Bulgarian Japanese English U.K.
Lenovo IdeaPad S10-3s Table 7.
IdeaPad S10-3s Hardware Maintenance Manual Miscellaneous parts Table 8. Parts list—Miscellaneous parts FRU System miscellaneous parts: • (a ) LM30 TOUCHPAD BRACKE • (b ) LM30 HDD BRACKET Cable miscellaneous parts: • (c ) LM30 C.A. FFC TOUCH PAD JH • (d ) LM30 C.A. FFC I/O TR • (e ) LM30 BLUETOOTH HT C.A. Note: Italicized letters in parentheses are references to the exploded view in “Overall” on page 63.
Lenovo IdeaPad S10-3s AC adapters Table 9. Parts list—3-pin AC adapters FRU P/N 30W white 3PIN, Delta ADP-30SH BB 20V1.5A 30W white 3PIN, Liteon PA-1300-12LC 20V1.5A 30W white 3PIN, Chicony CPA09-A030 20V1.5A 30W black 3PIN, Delta ADP-30SH BA 20V1.5A 30W black 3PIN, Liteon PA-1300-12LC 20V1.5A 30W black 3PIN, Chicony CPA09-A030 20V1.
IdeaPad S10-3s Hardware Maintenance Manual Power cords A Lenovo IdeaPad power cord for a specific country or region is usually available only in that country or region: Table 10.
Lenovo IdeaPad S10-3s Table 10.
IdeaPad S10-3s Hardware Maintenance Manual Notices Lenovo may not offer the products, services, or features discussed in this document in all countries. Consult your local Lenovo representative for information on the products and services currently available in your area. Any reference to a Lenovo product, program, or service is not intended to state or imply that only that Lenovo product, program, or service may be used.
Notices Any performance data contained herein was determined in a controlled environment. Therefore, the result obtained in other operating environments may vary significantly. Some measurements may have been made on development-level systems and there is no guarantee that these measurements will be the same on generally available systems. Furthermore, some measurements may have been estimated through extrapolation. Actual results may vary.
