ThinkPad® T61 and T61p (14.
ThinkPad® T61 and T61p (14.
Note Before using this information and the product it supports, be sure to read the general information under “Notices” on page 167. Fifth Edition (September 2011) © Copyright Lenovo 2007, 2011. LIMITED AND RESTRICTED RIGHTS NOTICE: If data or software is delivered pursuant a General Services Administration “GSA” contract, use, reproduction, or disclosure is subject to restrictions set forth in Contract No. GS-35F-05925.
Contents About this manual . . . . . . . . . . v Safety information . . . . . . . . . . 1 General safety . . . . . . . . . . . . . . 2 Electrical safety . . . . . . . . . . . . . 3 Safety inspection guide . . . . . . . . . . . 5 Handling devices that are sensitive to electrostatic discharge . . . . . . . . . . . . . . . 6 Grounding requirements . . . . . . . . . . 6 Safety notices: multilingual translations . . . . . 7 Laser compliance statement . . . . . . . . . 14 Important service information . . . . .
Recovery discs . . . Common service tools . . . . . . . . . . . . . . . . . 156 . 165 Trademarks . Notices . . . . . . . . . . . . . . 167 iv ThinkPad T61 and T61p (14.1-inch) Hardware Maintenance Manual . . . . . . . . . . . . .
About this manual This manual contains service and reference information for the following ThinkPad® products. ThinkPad T61 and T61p (14.1-inch) MT 8889, 8890, 8891, 8892, 8893, 8894, 8895, 8896, 8897, 8898, 8899, 8900, 8938, and 8939 Use this manual along with the advanced diagnostic tests to troubleshoot problems. The manual is divided into sections as follows: v The common sections provide general information, guidelines, and safety information required in servicing computers.
vi ThinkPad T61 and T61p (14.
Safety information This chapter presents following safety information that you need to be familiar with before you service a ThinkPad computer.
General safety Follow these rules to ensure general safety: v Observe good housekeeping in the area of the machines during and after maintenance. v When lifting any heavy object: 1. Make sure that you can stand safely without slipping. 2. Distribute the weight of the object equally between your feet. 3. Use a slow lifting force. Never move suddenly or twist when you attempt to lift. 4. Lift by standing or by pushing up with your leg muscles; this action removes the strain from the muscles in your back.
Electrical safety Observe the following rules when working on electrical equipment. Important: Use only approved tools and test equipment. Some hand tools have handles covered with a soft material that does not insulate you when working with live electrical currents. Many customers have, near their equipment, rubber floor mats that contain small conductive fibers to decrease electrostatic discharges. Do not use this type of mat to protect yourself from electrical shock.
v Do not touch live electrical circuits with the reflective surface of a plastic dental mirror. The surface is conductive; such touching can cause personal injury and machine damage. v Do not service the following parts with the power on when they are removed from their normal operating places in a machine: – Power supply units – Pumps – Blowers and fans – Motor generators and similar units. (This practice ensures correct grounding of the units.
Safety inspection guide The purpose of this inspection guide is to assist you in identifying potentially unsafe conditions. As each machine was designed and built, required safety items were installed to protect users and service personnel from injury. This guide addresses only those items. You should use good judgment to identify potential safety hazards due to attachment of non-ThinkPad features or options not covered by this inspection guide.
Handling devices that are sensitive to electrostatic discharge Any computer part containing transistors or integrated circuits (ICs) should be considered sensitive to electrostatic discharge (ESD.) ESD damage can occur when there is a difference in charge between objects. Protect against ESD damage by equalizing the charge so that the machine, the part, the work mat, and the person handling the part are all at the same charge. Notes: 1.
Safety notices: multilingual translations The safety notices in this section are provided in English, French, German, Hebrew, Italian, Japanese, and Spanish. Safety notice 1 Before the computer is powered on after FRU replacement, make sure all screws, springs, and other small parts are in place and are not left loose inside the computer. Verify this by shaking the computer and listening for rattling sounds. Metallic parts or metal flakes can cause electrical shorts.
Safety notice 2 DANGER Some standby batteries contain a small amount of nickel and cadmium. Do not disassemble a standby battery, recharge it, throw it into fire or water, or short-circuit it. Dispose of the battery as required by local ordinances or regulations. Use only the battery in the appropriate parts listing. Use of an incorrect battery can result in ignition or explosion of the battery. Certaines batteries de secours contiennent du nickel et du cadmium.
Safety notice 3 DANGER The battery pack contains small amounts of nickel. Do not disassemble it, throw it into fire or water, or short-circuit it. Dispose of the battery pack as required by local ordinances or regulations. Use only the battery in the appropriate parts listing when replacing the battery pack. Use of an incorrect battery can result in ignition or explosion of the battery. La batterie contient du nickel. Ne la démontez pas, ne l’exposez ni au feu ni à l’eau. Ne la mettez pas en court-circuit.
Safety notice 4 DANGER The lithium battery can cause a fire, an explosion, or a severe burn. Do not recharge it, remove its polarized connector, disassemble it, heat it above 100°C (212°F), incinerate it, or expose its cell contents to water. Dispose of the battery as required by local ordinances or regulations. Use only the battery in the appropriate parts listing. Use of an incorrect battery can result in ignition or explosion of the battery. La pile de sauvegarde contient du lithium.
Safety notice 5 If the LCD breaks and the fluid from inside the LCD gets into your eyes or on your hands, immediately wash the affected areas with water for at least 15 minutes. Seek medical care if any symptoms from the fluid are present after washing. Si le panneau d’affichage à cristaux liquides se brise et que vous recevez dans les yeux ou sur les mains une partie du fluide, rincez-les abondamment pendant au moins quinze minutes. Consultez un médecin si des symptômes persistent après le lavage.
Safety notice 6 DANGER To avoid shock, do not remove the plastic cover that protects the lower part of the inverter card. Afin d’éviter tout risque de choc électrique, ne retirez pas le cache en plastique protégeant la partie inférieure de la carte d’alimentation. Aus Sicherheitsgründen die Kunststoffabdeckung, die den unteren Teil der Spannungswandlerplatine umgibt, nicht entfernen.
Safety notice 8 DANGER Before removing any FRU, power off the computer, unplug all power cords from electrical outlets, remove the battery pack, and then disconnect any interconnecting cables. Avant de retirer une unité remplaçable en clientèle, mettez le système hors tension, débranchez tous les cordons d’alimentation des socles de prise de courant, retirez la batterie et déconnectez tous les cordons d’interface.
Laser compliance statement Some models of ThinkPad computer are equipped from the factory with an optical storage device such as a CD-ROM drive or a DVD-ROM drive. Such devices are also sold separately as options. If one of these drives is installed, it is certified in the U.S. to conform to the requirements of the Department of Health and Human Services 21 Code of Federal Regulations (DHHS 21 CFR) Subchapter J for Class 1 laser products.
A CD-ROM drive, a DVD-ROM drive, or any other storage device installed may contain an embedded Class 3A or Class 3B laser diode. Note the following: DANGER Emits visible and invisible laser radiation when open. Do not stare into the beam, do not view directly with optical instruments, and avoid direct exposure to the beam. Radiação por raio laser ao abrir. Não olhe fixo no feixe de luz, não olhe diretamente por meio de instrumentos óticos e evite exposição direta com o feixe de luz.
16 ThinkPad T61 and T61p (14.
Important service information This chapter presents following important service information: v “Strategy for replacing FRUs” – “Strategy for replacing a hard disk drive” on page 18 – “Important notice for replacing a system board” on page 18 – “How to use error message” on page 18 v “Strategy for replacing FRUs for CTO, CMV, and GAV” on page 19 – “Product definition” on page 19 – “FRU identification for CTO, CMV, and GAV products” on page 19 v “Important information about replacing RoHS compliant FRUs” on p
v Some computers have both a processor board and a system board. If you are instructed to replace either the processor board or the system board, and replacing one of them does not correct the problem, reinstall that board, and then replace the other one. v If an adapter or a device consists of more than one FRU, any of the FRUs may be the cause of the error. Before replacing the adapter or device, remove the FRUs, one by one, to see if the symptoms change. Replace only the FRU that changed the symptoms.
Strategy for replacing FRUs for CTO, CMV, and GAV Product definition Dynamic Configure To Order (CTO) This provides the ability for a customer to configure an IBM® or a Lenovo™ solution from an eSite, and have this configuration sent to fulfillment, where it is built and shipped directly to the customer. The machine label, Product Entitlement Warehouse (PEW), eSupport, and the HMM will load these products as the 4-digit MT and 3-digit model, where model = “CTO” (Example: 1829-CTO).
warranty.vm&sitestyle=lenovo Select Warranty lookup. Input the MT and the Serial number and the list of key commodities will be returned in the PEW record under COMPONENT INFORMATION. v Business Partners using Eclaim will access PEW when performing Entitlement Lookup. Business Partners will enter Loc ID, MT and Serial, and the key commodities will be returned in the Eclaim record under SYSTEM DETAILS. v Authorized IBM Business Partners can access Eclaim at the following Web site: https://wca.eclaim.
Important information about replacing RoHS compliant FRUs RoHS, The Restriction of Hazardous Substances in Electrical and Electronic Equipment Directive (2002/95/EC) is a European Union legal requirement affecting the global electronics industry. RoHS requirements must be implemented on Lenovo products placed on the market after June 2006. Products on the market before June 2006 are not required to have RoHS compliant parts.
22 ThinkPad T61 and T61p (14.
General checkout This chapter presents following information: v “What to do first” on page 24 v “Checkout guide” on page 25 – “Diagnostics using PC-Doctor for DOS” on page 26 – “PC-Doctor for Windows” on page 29 – “PC-Doctor for Rescue and Recovery” on page 29 v “Power system checkout” on page 30 The descriptions in this chapter apply to any ThinkPad model that supports the PC-Doctor® for DOS diagnostics program. Some descriptions might not apply to your particular computer.
What to do first When you do return a FRU, you must include the following information in the parts exchange form or parts return form that you attach to it: __ 1. Name and phone number of servicer __ 2. Date of service __ 3. Date on which the machine failed __ 4. Date of purchase __ 5. Failure symptoms, error codes appearing on the display, and beep symptoms __ 6. Procedure index and page number in which the failing FRU was detected __ 7. Failing FRU name and part number __ 8.
Checkout guide Use the following procedures as a guide in identifying and correcting problems with the ThinkPad computer. Note: The diagnostic tests are intended to test only ThinkPad products. The use of non-ThinkPad products, prototype cards, or modified options can lead to false indications of errors and invalid system responses. 1. Identify the failing symptoms in as much detail as possible. 2. Verify the symptoms.
Diagnostics using PC-Doctor for DOS The ThinkPad computer has a test program called PC-Doctor for DOS (hereafter called PC-Doctor.) You can detect errors by running the diagnostics test included in PC-Doctor. This section is an overview of the procedure. For details that depend on model-unique functions, refer to “ThinkPad T61 and T61p (14.1-inch)” on page 47. Note: PC-Doctor for DOS is available at following Web site: http://www.lenovo.
On the first screen, select the model and press Enter. Follow the instructions on the screen. 2. The main panel of PC-Doctor appears. 3. Select Diagnostics with the arrow keys, and press Enter. A pull-down menu appears. (Its exact form depends on the model.) Note: PC-Doctor menu does not mean the formal support device list. Some unsupported device names may appear in the PC-Doctor menu.
5. Follow the instructions on the screen. If there is a problem, PC-Doctor shows messages describing it. 6. To exit the test, select Quit — Exit Diag. To cancel the test, press Esc. Note: After running PC-Doctor, check the time and date on the system and reset them if they are incorrect. 28 ThinkPad T61 and T61p (14.
Detecting system information with PC-Doctor PC-Doctor can detect the following system information: Hardware Info v System Configuration v Memory Contents v Physical Disk Drives v Logical Disk Drives v VGA Information v IDE Drive Info v PCI Information v PNPISA Info v SMBIOS Info v VESA LCD Info v Hardware Events Log Utility v v v v v v v v v v v Run External Tests Surface Scan Hard Disk Benchmark System DOS Shell Tech Support Form Battery Rundown View Test Log Print Log Save Log Full Erase Hard Drive Quick
Power system checkout To 1. 2. 3. 4. 5. 6. 7. verify a symptom, do the following: Turn off the computer. Remove the battery pack. Connect the ac adapter. Check that power is supplied when you turn on the computer. Turn off the computer. Disconnect the ac adapter and install the charged battery pack. Check that the battery pack supplies power when you turn on the computer.
Checking operational charging To check whether the battery charges properly during operation, use a discharged battery pack or a battery pack that has less than 50% of the total power remaining when installed in the computer. Perform operational charging. If the battery status indicator or icon does not turn on, remove the battery pack and let it return to room temperature. Reinstall the battery pack. If the charge indicator or icon still does not turn on, replace the battery pack.
Checking the backup battery Do the following: 1. Power off the computer, and unplug the ac adapter from it. 2. Turn the computer upside down. 3. Remove the battery pack (see “1010 Battery pack” on page 62). 4. Remove the backup battery (see “1100 Backup battery” on page 80). 5. Measure the voltage of the backup battery. See the following figure. Red (+) Black (-) Wire Voltage (V dc) Red +2.5 to +3.2 Black Ground v If the voltage is correct, replace the system board.
Related service information This chapter presents following information: v “Restoring the factory contents by using Product Recovery discs” v “Passwords” on page 34 v “Power management” on page 37 v “Symptom-to-FRU index” on page 39 Service Web site: When the latest maintenance diskette and the system program service diskette become available, they will be posted on http://www.lenovo.
5. You will then be prompted to insert Product Recovery Disk 1 into the optical drive. Insert the Product Recovery Disk 1 into the optical drive, and press OK. In similar fashion, you will be prompted to insert the remaining recovery discs until all the files are copied. 6. After all the files are copied, the computer will restart and return to the “Welcome to Rescue and Recovery” screen where a window “Recovering your system, this may take several minutes” appears and .IMZ files are processed.
Hard-disk password There are two hard-disk passwords (HDPs): v User HDP—for the user v Master HDP—for the system administrator, who can use it to get access to the hard disk even if the user has changed the user HDP Note: There are two modes for the HDP: User only and Master + User. The Master + User mode requires two HDPs; the system administrator enters both in the same operation. The system administrator then provides the user HDP to the system user.
For models supporting the Passphrase function, press F1 while the POP icon is appearing on the screen; then enter the POP. For the other models, enter the POP. Note: To check whether the ThinkPad computer supports the Passphrase function, enter the BIOS Setup Utility and go to Security --> Password. If the Using Passphrase item is displayed in the menu, this function is available on the ThinkPad computer. 2. Click Access BIOS. The system Restart Required window is displayed. 3. Click Yes.
Power management To reduce power consumption, the computer has three power management modes: screen blank, standby, and hibernation. Screen blank mode If the time set on the “Turn off monitor” timer in the operating system expires, the LCD backlight turns off. To put the computer into screen blank mode, press the ThinkVantage button and use the ThinkVantage Productivity Center. To end screen blank mode and resume normal operation, press any key.
v The ring indicator (RI) is signaled by a serial device or a PC Card device. v The time set on the resume timer elapses. Note: The computer does not accept any input immediately after it enters standby mode. Wait a few seconds before taking any action to reenter operation mode. Hibernation mode In hibernation mode, the following occurs: v The system status, RAM, VRAM, and setup data are stored on the hard disk. v The system is powered off.
Symptom-to-FRU index This section contains following information: v “Numeric error codes” v “Error messages” on page 43 v “Beep symptoms” on page 44 v “No-beep symptoms” on page 44 v “LCD-related symptoms” on page 45 v “Intermittent problems” on page 46 v “Undetermined problems” on page 46 The symptom-to-FRU index in this section lists symptoms and errors and their possible causes. The most likely cause is listed first, in boldface type.
Table 1. Numeric error codes (continued) Symptom or error FRU or action, in sequence 0187 EAIA data access error—The access to EEPROM is failed. System board. 0188 Invalid RFID Serialization Information Area. System board. 0189 System board. Invalid RFID configuration information area—The EEPROM checksum is not correct. 40 0190 Critical low-battery error 1. Charge the battery pack. 2. Battery pack. 0191 System Security—Invalid Remote Change requested. 1.
Table 1. Numeric error codes (continued) Symptom or error FRU or action, in sequence 0250 System battery error—System battery is dead. 1. Charge the backup battery for more than 8 hours by connecting the ac adapter. 2. Replace the backup battery and run BIOS Setup Utility to reset the time and date. 0251 System CMOS checksum bad— Default configuration used. 1. Charge the backup battery for more than 8 hours by connecting the ac adapter. 2.
Table 1. Numeric error codes (continued) Symptom or error FRU or action, in sequence 1804 Unauthorized WAN card is plugged in—Power off and remove the WAN card. 1. Remove the WAN card that you installed. 2. System board. 1805 Unauthorized Wireless USB card is plugged in—Power off and remove the Wireless USB card. 1. Remove the Wireless USB card that you installed. 2. System board. 1820 More than one external fingerprint reader is attached.
Error messages Table 2. Error messages Symptom or error FRU or action, in sequence Device address conflict. 1. Load “Setup Defaults” in the BIOS Setup Utility. 2. Backup battery. 3. System board. Allocation error for device. 1. Load “Setup Defaults” in the BIOS Setup Utility. 2. Backup battery. 3. System board. Failing bits: nnnn. 1. DIMM. 2. System board. Invalid system configuration data. 1. DIMM. 2. System board. I/O device IRQ conflict. 1. Load “Setup Defaults” in the BIOS Setup Utility. 2.
Beep symptoms Table 3. Beep symptoms Symptom or error FRU or action, in sequence One beep and a blank, unreadable, or flashing LCD. 1. 2. 3. 4. One long and two short beeps, and a blank or unreadable LCD. 1. System board. 2. LCD assembly. 3. DIMM. Two short beeps with error codes. POST error. See “Numeric error codes” on page 39. Two short beeps and a blank screen. 1. System board. 2. DIMM. Three short beeps, pause, three more short beeps, and one short beep. 1. DIMM. 2.
LCD-related symptoms Important:The TFT LCD for the notebook computer contains many thin-film transistors (TFTs). The presence of a small number of dots that are missing, discolored, or always lighted is characteristic of TFT LCD technology, but excessive pixel problems can cause viewing concerns. The LCD should be replaced if the number of missing, discolored, or lighted dots in any background is as follows: Table 5.
Intermittent problems Intermittent system hang problems can be due to a variety of causes that have nothing to do with a hardware defect, such as cosmic radiation, electrostatic discharge, or software errors. FRU replacement should be considered only when a problem recurs. When analyzing an intermittent problem, do the following: 1. Run the diagnostic test for the system board in loop mode at least 10 times. 2. If no error is detected, do not replace any FRUs. 3.
ThinkPad T61 and T61p (14.1-inch) This chapter presents following product-specific service references and product-specific parts information. v “Specifications” v “Status indicators” on page 50 v “FRU tests” on page 53 v “Fn key combinations” on page 55 v “FRU replacement notices” on page 58 v “Removing and replacing a FRU” on page 61 v “Locations” on page 119 v “Parts list” on page 121 Specifications The following table lists the specifications of the ThinkPad T61 and T61p (14.1-inch) : Table 7.
Table 7. Specifications (continued) Feature Description Standard memory v 512-MB DDR2-667 SDRAM SO-DIMM (PC2-5300) card × 1 v 1-GB DDR2-667 SDRAM SO-DIMM (PC2-5300) card × 1 v 2-GB DDR2-667 SDRAM SO-DIMM (PC2-5300) card × 1 Optional memory v 512-MB DDR2-667 SDRAM SO-DIMM (PC2-5300) card × 1 v 1-GB DDR2-667 SDRAM SO-DIMM (PC2-5300) card × 1 v 2-GB DDR2-667 SDRAM SO-DIMM (PC2-5300) card × 1 (maximum of 4.0 GB) CMOS RAM v 242 bytes Hard disk drive v v v v v v v v v v 60 GB, 5400 rpm, 9.
Table 7. Specifications (continued) Feature Description Modem v ThinkPad Modem (MDC-1.5, 56 kbps HDA) Touch pad v UltraNav® ThinkLight® Yes Battery v Li-ion battery (6 cells) 5.2 Ah v Li-ion battery (9 cells) 7.
Status indicators The system status indicators show the status of the computer, as follows: 1 2 3 4 5 6 7 8 9 10 11 10 50 9 8 ThinkPad T61 and T61p (14.
Table 8. Status indicators Indicator Meaning 1 Wireless status Green: The wireless feature (the IEEE 802.11 standard or IEEE 802.11n) is on, and the radio link is ready for use. Blinking green: Data is being transmitted. 2 Wireless PAN status Green: Bluetooth wireless is operational. This indicator is on when Bluetooth wireless is on and not in suspend mode. R 3 Wireless WAN status Green: The wireless WAN is on, and the radio link is ready for use. Blinking green: Data is being transmitted.
Table 8. Status indicators (continued) 52 Indicator Meaning 11 Green: An Ultrabay Slim device is installed and in use. Blinking green: An Ultrabay Slim device is in the process of being detached. Turn off: An Ultrabay Slim device is ready to be attached or detached. Note: If you are using Windows 2000, the Ultrabay Slim status indicator does not blink while an Ultrabay Slim device is being detached. Instead, a message box pops up when the process is completed; then the indicator turns off.
FRU tests The following table shows the test for each FRU. Table 9. FRU tests FRU Applicable test System board 1. Diagnostics --> CPU/Coprocessor 2. Diagnostics --> Systemboard 3. If the ThinkPad Advanced Dock, the ThinkPad Advanced Mini Dock or the ThinkPad Essential Port Replicator is attached to the ThinkPad computer, detach it. Place the computer on a horizontal surface, and run Diagnostics --> ThinkPad Devices --> HDD Active Protection Test.
Table 9. FRU tests (continued) FRU Applicable test Diskette drive 1. Diagnostics --> Diskette Drives 2. Interactive Tests --> Diskette DVD drive or DVD/CD-RW combo drive 1. Diagnostics --> Other Devices--> Optical Drive 2. Interactive Tests --> Optical Drive Test Memory 1. If two DIMMs are installed, remove one of them and run Diagnostics --> Memory Test—Quick. 2. If the problem does not recur, return the DIMM to its place, remove the other one, and run the test again. 3.
Fn key combinations The following table shows the function of each combination of Fn with a function key. Table 10. Fn key combinations Key combination Description Fn+F1 Reserved. Fn+F2 Reserved. Fn+F3 Select a power scheme that has been created by Power Manager. When you press this combination, a panel for selecting a power scheme appears. Notes: 1. To use the Fn+F3 key combination, you must have the ThinkPad PM device driver installed on the computer. 2.
Table 10. Fn key combinations (continued) Key combination Description Fn+F7 Apply a presentation scheme directly, with no need to start Presentation Director. To disable this function and use the Fn+F7 key combination for switching a display output location, start Presentation Director, and change the settings. Switch a display output location v External monitor (CRT display) v Computer display and external monitor (LCD + CRT display) v Computer display (LCD) Notes: 1.
Table 10. Fn key combinations (continued) Key combination Description Fn+Spacebar Enable the FullScreen Magnifier function. Fn+PrtSc Has the same function as the SysRq key. Fn+ScrLk Enable or disable the numeric keypad. Fn+Pause Has the same function as the Break key. Fn+cursor keys These key combinations work with Windows Windows Media Player.
FRU replacement notices This section contains notices related to removing and replacing parts. Read this section carefully before replacing any FRU. Screw notices Loose screws can cause a reliability problem. In the ThinkPad computer, this problem is addressed with special nylon-coated screws that have the following characteristics: v They maintain tight connections. v They do not easily come loose, even with shock or vibration. v They are harder to tighten. v Each one should be used only once.
Retaining serial numbers This section includes the following descriptions: v “Restoring the serial number of the system unit” v “Retaining the UUID” v “Reading or writing the ECA information” on page 60 Restoring the serial number of the system unit When the computer was manufactured, the EEPROM on the system board was loaded with the serial numbers of the system and all major components. These numbers need to remain the same throughout the life of the computer.
Reading or writing the ECA information Information on Engineering Change Announcements (ECA) are stored in the EEPROM of the system board. The electronic storage of this information simplifies the procedure to check if the ECA has been previously applied to a machine. The machine does not need to be disassembled to check for the ECA application. To check what ECAs have been previously applied to the machine, use the ECA Information Read/Write function on the ThinkPad Hardware Maintenance Diskette Version 1.
Removing and replacing a FRU This section presents directions and drawings for use in removing and replacing a FRU. Be sure to observe the following general rules: 1. Do not try to service any computer unless you have been trained and certified. An untrained person runs the risk of damaging parts. 2. Before replacing any FRU, review “FRU replacement notices” on page 58. 3. Begin by removing any FRUs that have to be removed before the failing FRU. Any such FRUs are listed at the top of the page.
1010 Battery pack DANGER Use only the battery specified in the parts list for your computer. Any other battery could ignite or explode. Table 11. Removal steps of battery pack Unlock the battery release lever 1 . Holding the battery release lever in the unlocked position 2 , remove the battery pack in the direction shown by arrow 3 . 1 2 3 When installing: Install the battery pack along the slide rails of the slot. Then make sure that the battery release lever is in the locked position.
1020 Ultrabay Slim device Note: Ultrabay Slim does not accept any of the following devices: v Ultrabay Plus™ devices v Ultrabay 2000™ devices v Ultrabay Enhanced devices Table 12. Removal steps of Ultrabay Slim device When you release the switch in step 1 , the lever pops out. In step 2 , pull the lever a little to release the device from the bay. 1 2 3 ThinkPad T61 and T61p (14.
1030 Hard disk drive (HDD) cover, HDD, and HDD rubber rails For access, remove this FRU: v “1010 Battery pack” on page 62 Attention: v Do not drop the hard disk drive or apply any physical shock to it. The hard disk drive is sensitive to physical shock. Improper handling can cause damage and permanent loss of data. v Before removing the drive, have the user make a backup copy of all the information on it if possible. v Never remove the drive while the system is operating or is in suspend mode. Table 13.
Table 13. Removal steps of HDD cover, HDD, and HDD rubber rails (continued) 3 4 When installing: Make sure that the hard disk drive connector is attached firmly. 5 5 When installing: The rubber rails on the hard disk drive must be attached to the replacement drive. Otherwise the drive cannot be installed properly. ThinkPad T61 and T61p (14.
1040 Palm rest or palm rest with fingerprint reader For access, remove this FRU in order: v “1010 Battery pack” on page 62 Note: In models with the fingerprint reader, the sensor is attached to the palm rest FRU. If the fingerprint reader has any defects, you can replace it by the procedures given in this section, which are the same for a palm rest with or without a fingerprint reader. Table 14.
Table 14. Removal steps of palm rest (continued) 2 2 3 4 Table 15. Installation of the palm rest When installing: When you attach the palm rest, do as follows: ThinkPad T61 and T61p (14.
Table 15. Installation of the palm rest (continued) 1. Attach the fingerprint reader connector firmly to the system board. 2. Press the left and right top edges of the palm rest to fit it into place. 68 ThinkPad T61 and T61p (14.
Table 15. Installation of the palm rest (continued) 3. Push the front side of the palm rest until it clicks into place. 4. Close the LCD cover, and turn the computer over. Then fasten the four screws to secure the palm rest. ThinkPad T61 and T61p (14.
1050 DIMM For access, remove these FRUs in order: v “1010 Battery pack” on page 62 v “1040 Palm rest or palm rest with fingerprint reader” on page 66 Table 16. Removal steps of DIMM Note: If only one DIMM is used on the computer you are servicing, the card must be installed in SLOT-0 ( a ), but not in SLOT-1 ( b ). 1 b 2 a 1 When installing: Insert the notched end of the DIMM into the socket. Press the DIMM firmly, and pivot it until it snaps into the place.
1060 Keyboard For access, remove these FRUs in order: v “1010 Battery pack” on page 62 v “1040 Palm rest or palm rest with fingerprint reader” on page 66 Table 17. Removal steps of keyboard 1 Step 1 Icon Screw (quantity) Color Torque M2 × 14 mm, flat-head, nylon-coated (1) Black 0.167 Nm (1.7 kgfcm) Lift the keyboard a little in the direction shown by arrow 2 , and then detach the connector 3 . 2 3 ThinkPad T61 and T61p (14.
Table 17. Removal steps of keyboard (continued) When installing: Make sure that the keyboard edges a are under the frame as shown in this figure. a aa 72 ThinkPad T61 and T61p (14.
1070 Modem daughter card (MDC-1.5) For access, remove these FRUs in order: v “1010 Battery pack” on page 62 v “1040 Palm rest or palm rest with fingerprint reader” on page 66 v “1060 Keyboard” on page 71 Table 18. Removal steps of MDC-1.5 1 2 1 1 3 Step Screw (quantity) Color Torque 1 M2 × 3 mm, small-head, nylon-coated (2) Silver 0.167 Nm (1.7 kgfcm) Note: The bracket shown in step 2 is only for the models with wireless WAN.
Table 18. Removal steps of MDC-1.5 (continued) Turn the card over 4 , and detach the modem connector 5 . 4 5 When installing: Make sure that the modem connector and the connector on the underside of the card are attached firmly. 74 ThinkPad T61 and T61p (14.
1080 PCI Express Mini Card for wireless LAN For access, remove these FRUs in order: v “1010 Battery pack” on page 62 v “1040 Palm rest or palm rest with fingerprint reader” on page 66 v “1060 Keyboard” on page 71 Table 19. Removal steps of PCI Express Mini Card for wireless LAN In step 1 , unplug the jacks by using the removal tool antenna RF connector (P/N: 08K7159) or pick the connectors with your fingers and gently unplug them in direction of the arrow.
Table 19. Removal steps of PCI Express Mini Card for wireless LAN (continued) 3 Table 20. Installation of the PCI Express Mini Card for wireless LAN When installing the card, do as follows: v Plug the gray cable into the jack labeled MAIN on the card, and the black cable into the jack labeled AUX. v If the computer you are servicing has three cables and the 802.11 a/b/g wireless LAN card, put the white cable in the cable bag in the card slot. 76 ThinkPad T61 and T61p (14.
Table 20. Installation of the PCI Express Mini Card for wireless LAN (continued) v Some ThinkPad computer has three cables and the 802.11 a/b/g/n wireless LAN card. In that case, plug the gray cable (MAIN) into the jack labeled TR1 , the white cable (3rd) into jack labeled R0 , and the black cable (AUX) into jack labeled TR2 on the card. v After you secure the card, make sure that the antenna cables are routed as shown in the each figure. ThinkPad T61 and T61p (14.
1090 PCI Express Mini Card for wireless WAN For access, remove these FRUs in order: v “1010 Battery pack” on page 62 v “1040 Palm rest or palm rest with fingerprint reader” on page 66 v “1060 Keyboard” on page 71 Table 21. Removal steps of PCI Express Mini Card for wireless WAN In step 1 , unplug the jacks by using the removal tool antenna RF connector (P/N: 08K7159) or pick the connectors with your fingers and gently unplug them in direction of the arrow.
Table 21. Removal steps of PCI Express Mini Card for wireless WAN (continued) 3 ThinkPad T61 and T61p (14.
1100 Backup battery DANGER Use only the battery specified in the parts list for your computer. Any other battery could ignite or explode. For access, remove these FRUs in order: v “1010 Battery pack” on page 62 v “1040 Palm rest or palm rest with fingerprint reader” on page 66 v “1060 Keyboard” on page 71 Table 22. Removal steps of backup battery 2 1 When installing: Make sure that the battery connector is attached firmly. 80 ThinkPad T61 and T61p (14.
1110 SIM card slot For access, remove these FRUs, in order: v “1010 Battery pack” on page 62 v “1040 Palm rest or palm rest with fingerprint reader” on page 66 v “1060 Keyboard” on page 71 Note: If the SIM card has been inserted in its slot, remove it before you start the servicing. After you finish the servicing, make sure that you insert the card back into the slot firmly. Table 23. Removal steps of SIM card slot 1 2 Step Screw (quantity) Color Torque 1 M2 × 3.
1120 Keyboard bezel For access, remove these FRUs in order: v “1010 Battery pack” on page 62 v “1040 Palm rest or palm rest with fingerprint reader” on page 66 v “1060 Keyboard” on page 71 Table 24. Removal steps of keyboard bezel 1 2 82 Step Screw (quantity) Color Torque 1 M2 × 14 mm, flat-head, nylon-coated (1) Black 0.167 Nm (1.7 kgfcm) 2 M2 × 19 mm, bind-head, nylon-coated (1) Black 0.167 Nm (1.7 kgfcm) ThinkPad T61 and T61p (14.
Table 24. Removal steps of keyboard bezel (continued) 4 3 4 In step 3 , release the wireless antenna cables from the cable guide. Step Screw (quantity) Color Torque 4 M2 × 3.5 mm, flatl-head, nylon-coated (2) Black 0.167 Nm (1.7 kgfcm) In step 5 , detach the claws. Then remove the keyboard bezel in the direction shown by arrow 6 . 5 5 6 5 5 6 When installing: Make sure that all the claws are attached firmly. Then fasten the screws to secure the keyboard bezel.
1130 Fan assembly For access, remove these FRUs in order: v “1010 Battery pack” on page 62 v “1040 Palm rest or palm rest with fingerprint reader” on page 66 v “1060 Keyboard” on page 71 v “1120 Keyboard bezel” on page 82 Table 25. Removal steps of fan assembly 2 2 1 1 3 84 3 Step Screw (quantity) Color Torque 1 M2 × 3 mm, small-head, nylon-coated (2) Silver 0.167 Nm (1.7 kgfcm) 2 M2 × 9.5 mm, flat-head, nylon-coated (2) Black 0.167 Nm (1.7 kgfcm) ThinkPad T61 and T61p (14.
Table 25. Removal steps of fan assembly (continued) 5 4 4 5 Step Screw (quantity) Color Torque 4 M2 × 9.5 mm, flat-head, nylon-coated (3) Black 0.167 Nm (1.7 kgfcm) Attention: Do not handle the fan roughly. Improper handling of the fan can cause distortion or deformation and imperfect contact with components. 7 6 ThinkPad T61 and T61p (14.
Table 26. Installation of the fan assembly When installing the fan assembly, do as follows: v Before you attach the fan assembly to the computer, apply thermal grease, at an amount of 0.2 grams, on the part marked a as in the following figure. Either too much or too less application of grease can cause a thermal problem due to imperfect contact with a component. a v Make sure that the fan connector is attached firmly.
1140 CPU For access, remove these FRUs in order: v “1010 Battery pack” on page 62 v “1040 Palm rest or palm rest with fingerprint reader” on page 66 v “1060 Keyboard” on page 71 v “1120 Keyboard bezel” on page 82 v “1130 Fan assembly” on page 84 Attention: CPU is extremely sensitive. When you service the CPU, avoid any kind of rough handling. Table 27. Removal steps of CPU Rotate the head of the screw in the direction shown by arrow 1 to release the lock; then remove the CPU.
1150 LCD assembly For access, remove these FRUs in order: v “1010 Battery pack” on page 62 v “1040 Palm rest or palm rest with fingerprint reader” on page 66 v “1060 Keyboard” on page 71 v “1080 PCI Express Mini Card for wireless LAN” on page 75 v “1090 PCI Express Mini Card for wireless WAN” on page 78 v “1120 Keyboard bezel” on page 82 Table 28. Removal steps of LCD assembly 1 1 88 Step Screw (quantity) Color Torque 1 M2 × 9.5 mm, flat-head, nylon-coated (2) Black 0.167 Nm (1.
Table 28. Removal steps of LCD assembly (continued) 4 4 3 2 3 Step Screw (quantity) Color Torque 3 M2 × 5 mm, flat-head, nylon-coated (2) Black 0.167 Nm (1.7 kgfcm) In step 4 , strip off the tapes securing the antenna cables, and release the cables from the cable guides of the frame. When installing: Do not pinch the antenna cables when you attach the LCD connector. ThinkPad T61 and T61p (14.
Table 28. Removal steps of LCD assembly (continued) 5 5 When installing: 1. As you route the cables, make sure that they are not subjected to any tension. Tension could cause the cables to be damaged by the cable guides, or a wire to be broken. 2. Make sure that the LCD connector is attached firmly. 90 ThinkPad T61 and T61p (14.
1160 Base cover For access, remove these FRUs, in order: v “1010 Battery pack” on page 62 v “1020 Ultrabay Slim device” on page 63 v “1030 Hard disk drive (HDD) cover, HDD, and HDD rubber rails” on page 64 v “1040 Palm rest or palm rest with fingerprint reader” on page 66 v “1060 Keyboard” on page 71 v “1070 Modem daughter card (MDC-1.
Table 29. Removal steps of base cover (continued) 3 2 2 92 Step Screw (quantity) Color Torque 2 M2 × 14 mm, flat-head, nylon-coated (2) Black 0.167 Nm (1.7 kgfcm) 3 M2 × 3.5 mm, flat-head, nylon-coated (1) Black 0.167 Nm (1.7 kgfcm) ThinkPad T61 and T61p (14.
Table 29. Removal steps of base cover (continued) a 4 4 5 Step Screw (quantity) Color Torque 4 M2 × 5 mm, flat-head, nylon-coated (2) Black 0.167 Nm (1.7 kgfcm) 5 M2 × 3 mm, small-head, nylon-coated (1) Silver 0.167 Nm (1.7 kgfcm) For discrete graphics models: When you are servicing, make sure that the thermal rubber for FET is firmly attached on the system board as shown in a .
Table 29. Removal steps of base cover (continued) Attention: Before step 6 , be sure that the Ultrabay Slim device eject lever has not popped out. It must be housed in its position as shown in the figure a . 6 7 a 94 ThinkPad T61 and T61p (14.
Table 30. Installation of the PC Card slot bezel When installing the PC Card slot bezel assembly, do as follows: For PC Card/ExpressCard slot bezel assembly 3 4 1 2 For PC Card/Smart Card slot bezel assembly 1 2 ThinkPad T61 and T61p (14.
Note: Applying labels to the base cover The new base cover FRU is shipped with a kit containing labels of several kinds. When you replace the base cover, you need to apply the following labels: a Windows license label (COA) b FCC label c Product label d FCC or homologation label or some models, you also need to apply one or two FCC labels b . Check the old base cover; if it has one or two FCC labels, find duplicates of them in the label kit and apply them to the new base cover.
1170 Speaker assembly For access, remove these FRUs in order: v “1010 Battery pack” on page 62 v “1020 Ultrabay Slim device” on page 63 v “1030 Hard disk drive (HDD) cover, HDD, and HDD rubber rails” on page 64 v “1040 Palm rest or palm rest with fingerprint reader” on page 66 v “1060 Keyboard” on page 71 v “1070 Modem daughter card (MDC-1.
1180 USB sub card with cable For access, remove these FRUs in order: v “1010 Battery pack” on page 62 v “1020 Ultrabay Slim device” on page 63 v “1030 Hard disk drive (HDD) cover, HDD, and HDD rubber rails” on page 64 v “1040 Palm rest or palm rest with fingerprint reader” on page 66 v “1060 Keyboard” on page 71 v “1070 Modem daughter card (MDC-1.
Table 31. Removal steps of USB sub card with cable (continued) 4 5 3 5 2 In step 4 , remove the security hole bracket in the direction of the arrow. Step Screw (quantity) Color Torque 3 M2 × 3.5 mm, flat-head, nylon-coated (1) Black 0.167 Nm (1.7 kgfcm) 5 M2 × 3.5 mm, flat-head, nylon-coated (2) Black 0.167 Nm (1.7 kgfcm) ThinkPad T61 and T61p (14.
1190 Structure frame For access, remove these FRUs, in order: v “1010 Battery pack” on page 62 v “1020 Ultrabay Slim device” on page 63 v “1030 Hard disk drive (HDD) cover, HDD, and HDD rubber rails” on page 64 v “1040 Palm rest or palm rest with fingerprint reader” on page 66 v “1060 Keyboard” on page 71 v “1070 Modem daughter card (MDC-1.
Table 32. Removal steps of structure frame (continued) Remove the ac power jack cable a and the modem cable b . 3 a b 4 6 5 2 4 When installing: Make sure the connectors are attached firmly, and that the cables are routed as in the figure above. ThinkPad T61 and T61p (14.
Table 32. Removal steps of structure frame (continued) Remove the CPU support plate. 8 7 Step Screw (quantity) Color Torque 7 M2 × 5 mm, flat-head, nylon-coated (1) Black 0.167 Nm (1.7 kgfcm) 10 9 10 9 9 9 11 a 11 Step Screw (quantity) Color Torque 9 M2 × 3.5 mm, flat-head, nylon-coated (5) Black 0.167 Nm (1.7 kgfcm) 10 M2 × 9.5 mm, flat-head, nylon-coated (2) Black 0.167 Nm (1.7 kgfcm) In step 11 , loosen the hex screws. 102 ThinkPad T61 and T61p (14.
Table 32. Removal steps of structure frame (continued) Remove the system board and the PC Card/ExpressCard slots assembly from the structure frame together. 13 12 When attaching the system board to the frame, do as follows: Table 33. Installation of the system board 1. Adjust the placement with the small projection a . Then attach the CPU support plate 1 . 1 a 2. Secure the screws in order as shown in this figure. Attention: Do not use an electric screwdriver to secure these screws.
1200 System board and PC Card/ExpressCard slots assembly Important notices for handling the system board: When handling the system board, bear the following in mind. v The system board has an accelerometer, which can be broken by applying several thousands of G-forces. Note: Dropping a system board from a height of as little as 6 inches so that it falls flat on a hard bench can subject the accelerometer to as much as 6,000 G’s of shock.
Following components soldered on the top side of the system board are extremely sensitive. When you service the system board, avoid any kind of rough handling. a Accelerometer chip for the HDD Active Protection System™ b Security chip c CPU d Video chip e MCH (Memory Controller Hub) f ICH (I/O Controller Hub) Bending or flexing the system board can cause ball grid array (BGA) connections to crack (unzip). c d f e b a Table 34.
Table 34. Removal steps of system board and PC Card/ExpressCard slots assembly (continued) Turn the system board over, and then disconnect the PC Card/ExpressCard slots assembly a from the system board. a 2 When installing: Make sure that the connector of the PC Card/Express Card slot assembly is attached to the system board firmly. 106 ThinkPad T61 and T61p (14.
2010 LCD cover kit For access, remove this FRU: v “1010 Battery pack” on page 62 Table 35. Removal steps of LCD cover kit 2 1 2 1 1 Step Screw cap Screw (quantity) Color Torque 1 M2.5 × 7 mm, bind-head, nylon-coated (3) Black 0.392 Nm (4 kgfcm) 2 M2.5 × 4 mm, bind-head, nylon-coated (2) Black 0.392 Nm (4 kgfcm) Close the LCD cover. Detach the LCD rear cover a little as shown in step 3 of this figure, and detach the rear edge of the LCD rear cover 4 .
Table 35. Removal steps of LCD cover kit (continued) Detach the left and right rear edges of the LCD rear cover 5 , and remove the cover in the direction of arrow 6 as shown in this figure. 5 6 5 Detach the latches on the top, left, and right edge of the LCD front bezel in the direction of arrow 7 as shown in this figure. 7 108 ThinkPad T61 and T61p (14.
Table 35. Removal steps of LCD cover kit (continued) Detach the latches on the front edge of the LCD front bezel in the direction of arrow 8 as shown in this figure. 8 8 8 8 8 Table 36. Installation of the LCD cover kit When installing: Attach the LCD cover kit as follows: 1. Place the LCD front bezel so that the LCD latch levers fit into the holes of the bezel 1 . Then align the front edge of the bezel to the frame, and attach the latches 2 . 1 1 2 2 2 ThinkPad T61 and T61p (14.
Table 36. Installation of the LCD cover kit (continued) 2. Attach all the latches on the top, left, and right edges of the bezel. 3 3 3 3 3 3 3 3 3 3. Attach the LCD rear cover from the top end. 4 4. Attach the latches of the LCD rear cover firmly. 5 5 5 5 5 110 ThinkPad T61 and T61p (14.
2020 Inverter card For access, remove these FRUs in order: v “1010 Battery pack” on page 62 v “2010 LCD cover kit” on page 107 Table 37. Removal steps of inverter card 1 1 2 3 Step Screw (quantity) Color Torque 1 M2 × 4 mm, flat-head, nylon-coated (2) Black 0.167 Nm (1.7 kgfcm) When installing: Make sure that connectors 3 and 4 are attached firmly. ThinkPad T61 and T61p (14.
2030 Bluetooth daughter card (BDC-2) For access, remove these FRUs in order: v “1010 Battery pack” on page 62 v “2010 LCD cover kit” on page 107 Table 38. Removal steps of BDC-2 1 2 Step Screw (quantity) Color Torque 1 M2 × 4 mm, flat-head, nylon-coated (1) Black 0.167 Nm (1.7 kgfcm) When installing: Make sure that connector is attached firmly. 112 ThinkPad T61 and T61p (14.
2040 Antenna assembly For access, remove these FRUs in order: v “1010 Battery pack” on page 62 v “1040 Palm rest or palm rest with fingerprint reader” on page 66 v “1060 Keyboard” on page 71 v “1080 PCI Express Mini Card for wireless LAN” on page 75 v “1090 PCI Express Mini Card for wireless WAN” on page 78 v “1120 Keyboard bezel” on page 82 v “1150 LCD assembly” on page 88 v “2010 LCD cover kit” on page 107 v “2020 Inverter card” on page 111 v “2030 Bluetooth daughter card (BDC-2)” on page 112 Table 39.
Table 39. Removal steps of antenna assembly (continued) 3 4 4 4 114 ThinkPad T61 and T61p (14.
2050 LCD magnesium frame assembly and hinge assembly For access, remove these FRUs in order: v “1010 Battery pack” on page 62 v “1040 Palm rest or palm rest with fingerprint reader” on page 66 v “1060 Keyboard” on page 71 v “1080 PCI Express Mini Card for wireless LAN” on page 75 v “1090 PCI Express Mini Card for wireless WAN” on page 78 v “1120 Keyboard bezel” on page 82 v “1150 LCD assembly” on page 88 v “2010 LCD cover kit” on page 107 v “2020 Inverter card” on page 111 v “2030 Bluetooth daughter card (B
Table 40. Removal steps of LCD magnesium frame assembly and hinge assembly (continued) 3 Step Screw (quantity) Color Torque 3 M2 × 3 mm, flat-head, nylon-coated (1) Silver 0.167 Nm (1.7 kgfcm) 5 4 a When installing: Attach the LCD panel so that the small hole on the right side of the panel fits into the small projection of the right hinge as shown in a . 116 ThinkPad T61 and T61p (14.
Table 40. Removal steps of LCD magnesium frame assembly and hinge assembly (continued) Remove the hinge assembly in step 6 . 6 6 ThinkPad T61 and T61p (14.
2060 LCD panel and LCD cable For access, remove these FRUs in order: v “1010 Battery pack” on page 62 v “1040 Palm rest or palm rest with fingerprint reader” on page 66 v “1060 Keyboard” on page 71 v “1080 PCI Express Mini Card for wireless LAN” on page 75 v “1090 PCI Express Mini Card for wireless WAN” on page 78 v “1120 Keyboard bezel” on page 82 v “1150 LCD assembly” on page 88 v “2010 LCD cover kit” on page 107 v “2020 Inverter card” on page 111 v “2030 Bluetooth daughter card (BDC-2)” on page 112 v “20
Locations Front view 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 ThinkLight Status indicators Note: For the description of each indicator, see “Status indicators” on page 50.
Rear view 1 2 3 4 5 6 7 8 9 10 Status indicators Note: For the description of each indicator, see “Status indicators” on page 50.
Parts list This section contains following lists of the service parts. v “Overall” on page 122 v “LCD FRUs” on page 146 v “Keyboard” on page 152 v “Miscellaneous parts” on page 153 v “AC adapters” on page 154 v “Power cords” on page 155 v “Recovery discs” on page 156 v “Common service tools” on page 165 Notes: v Each FRU is available for all types or models, unless specific types or models are specified.
Overall 1 24 23 2 3 22 a 21 f 4 c b 5 6 7 20 19 8 9 18 10 e d 17 16 11 12 13 15 14 122 ThinkPad T61 and T61p (14.
Table 42. Parts list—Overall No. FRU FRU no. RoHS ID CRU ID a - f See “Miscellaneous parts” on page 153. 1 LCD unit (see “LCD FRUs” on page 146.
Table 42. Parts list—Overall (continued) No. 124 FRU FRU no.
Table 42. Parts list—Overall (continued) No. 6 6 FRU FRU no. RoHS ID CRU ID ThinkPad 11a/b/g Wireless LAN Mini PCI Express Adapter v 8889-CTO, 24x v 8890-CTO, 24x v 8891-CTO v 8892-CTO v 8893-CTO v 8894-CTO v 8895-CTO, 2Bx v 8896-CTO, 2Bx v 8897-CTO v 8898-CTO v 8899-CTO v 8900-CTO v 8938-CTO v 8939-CTO xxB, xxC, xxF, xxG, xxH, xxL, xxM, xxP, xxQ, xxS, xxU, xxY 39T5578 R ** xxE, xxJ 39T5579 R ** xxV 39T5580 R ** xxA, xxT (802.
Table 42. Parts list—Overall (continued) No. 6 6 126 FRU FRU no. RoHS ID CRU ID ThinkPad 11a/b/g/n Wireless LAN Mini-PCI Express Adapter v 8889-CTO v 8890-CTO v 8891-CTO v 8892-CTO v 8893-CTO v 8894-CTO v 8895-CTO v 8896-CTO v 8897-CTO v 8898-CTO v 8899-CTO v 8900-CTO v 8938-CTO v 8939-CTO xxA, xxB, xxC, xxF, xxH, xxK, xxL, xxM, xxP, xxQ, xxS, xxU, xxY 42T0825 R ** xxE, xxJ 42T0827 R ** xxV 42T0829 R ** xxT (802.
Table 42. Parts list—Overall (continued) No. 6 FRU FRU no.
Table 42. Parts list—Overall (continued) No. 10 10 128 FRU FRU no. RoHS ID CRU ID SATA hard disk drive, 60 GB, 9.5 mm, 5,400 rpm v 8889-CTO, 5Xx, 5Yx, 5Zx v 8890-CTO v 8891-CTO v 8892-CTO, 2Xx v 8893-CTO v 8894-CTO v 8895-CTO, 2Rx, 2Ux, 2Xx, 2Zx, 35x, 3Hx, 3Jx, 3Mx, 6Fx, 6Gx, 6Hx, 6Jx, 6Kx v 8896-CTO v 8897-CTO, 2Sx, 2Yx, 36x, 6Nx v 8898-CTO v 8899-CTO v 8900-CTO v 8938-CTO v 8939-CTO Fujitsu 39T2883 R ** HGST OP 42T1489 R ** Seagate 42T1303 R ** SATA hard disk drive, 80 GB, 9.
Table 42. Parts list—Overall (continued) No. 10 10 FRU FRU no. RoHS ID CRU ID SATA hard disk drive, 120 GB, 9.
Table 42. Parts list—Overall (continued) No. 130 FRU FRU no. RoHS ID CRU ID 10 SATA hard disk drive, 160 GB (FDE), 9.5 mm, 5,400 42T1311 rpm, Seagate v 8889-CTO, 36x, 37x, 39x, 6Ax, 6Dx, 6Ex, 6Fx, 6Xx, A9x v 8890-CTO v 8891-CTO, 3Ax, 3Bx v 8892-CTO v 8893-CTO v 8894-CTO v 8895-CTO v 8896-CTO v 8897-CTO v 8898-CTO v 8899-CTO v 8900-CTO v 8938-CTO v 8939-CTO R ** 10 SATA hard disk drive, 250 GB, 9.
Table 42. Parts list—Overall (continued) No. 10 FRU FRU no. RoHS ID CRU ID SATA hard disk drive, 100 GB, 9.5 mm, 7,200 rpm v 8889-CTO, 2Nx, 35x, 3Dx, 3Fx, 3Hx, 5Wx, 6Gx, 6Hx, 6Jx, 6Kx v 8890-CTO v 8891-CTO v 8892-CTO, 2Zx, 3Gx v 8893-CTO v 8894-CTO v 8895-CTO, 5Yx, 64x, 66x v 8896-CTO v 8897-CTO v 8898-CTO, 22x, 5Bx, 5Tx v 8899-CTO v 8900-CTO v 8938-CTO v 8939-CTO, 34x HGST OP 42T1485 R ** Seagate 39T2799 R ** HGST 42T1461 R ** Seagate 42T1439 R ** 10 SATA hard disk drive, 200 GB, 9.
Table 42. Parts list—Overall (continued) No. 12 12 132 FRU FRU no.
Table 42. Parts list—Overall (continued) No. 13 13 FRU FRU no. RoHS ID CRU ID HLDS (GDR-80887N-C2 UBSS) 39T2683 R * PCC (UJDA775DVD UBSS) 39T2681 R * DVD drive, 9.5 mm v 8889-CTO, 5Xx, 5Yx, 5Zx v 8890-CTO v 8891-CTO v 8892-CTO v 8893-CTO v 8894-CTO v 8895-CTO, 2Zx, 6Fx v 8896-CTO v 8897-CTO v 8898-CTO, 5Bx, 5Cx v 8899-CTO v 8900-CTO v 8938-CTO v 8939-CTO DVD/CD-RW combo drive, 9.
Table 42. Parts list—Overall (continued) No. 13 FRU no. RoHS ID CRU ID DVD-RAM/RW drive, 9.
Table 42. Parts list—Overall (continued) No. 15 15 15 15 15 15 15 15 FRU FRU no.
Table 42. Parts list—Overall (continued) No. 15 15 15 16 136 FRU FRU no.
Table 42. Parts list—Overall (continued) No. FRU FRU no.
Table 42. Parts list—Overall (continued) No. 138 FRU FRU no.
Table 42. Parts list—Overall (continued) No. FRU FRU no.
Table 42. Parts list—Overall (continued) No. 140 FRU FRU no. RoHS ID CRU ID 19 CPU assembly, Intel Core 2 Duo processor T7100 (1.
Table 42. Parts list—Overall (continued) No. FRU FRU no. RoHS ID CRU ID 19 CPU assembly, Intel Core 2 Duo processor T7500 (2.2 GHz) v 8889-CTO, 22x, 23x, 2Cx, 2Dx, 2Fx, 2Ux, 2Wx, 32x, 3Hx, 6Ex, 6Gx, 6Hx, 6Mx, 6Nx, 6Qx v 8890-CTO, 2Ex, 2Gx v 8891-CTO v 8892-CTO, 2Vx v 8893-CTO v 8894-CTO v 8895-CTO, 3Gx, 3Px, 5Yx, 5Zx, 64x, 66x v 8896-CTO v 8897-CTO v 8898-CTO v 8899-CTO v 8900-CTO v 8938-CTO v 8939-CTO, 2Kx 42W7656 R N 19 CPU assembly, Intel Core 2 Duo processor T7500 (2.
Table 42. Parts list—Overall (continued) No. 142 FRU FRU no. RoHS ID CRU ID 19 CPU assembly, Intel Core 2 Duo processor T7700 (2.4 GHz) G-0 Step v 8889-CTO, 35x, 36x, 37x, 39x, 3Cx, 3Dx, 3Ex, 3Fx, 5Wx, 6Jx, 6Kx, 6Sx, 6Tx v 8890-CTO v 8891-CTO, 3Ax, 3Bx v 8892-CTO, 3Gx v 8893-CTO v 8894-CTO v 8895-CTO v 8896-CTO v 8897-CTO v 8898-CTO, 5Bx, 5Cx, 5Tx v 8899-CTO v 8900-CTO v 8938-CTO v 8939-CTO, 34x 42W7850 R N 19 CPU assembly, Intel Core 2 Duo processor T7800 (2.
Table 42. Parts list—Overall (continued) No. FRU FRU no. RoHS ID CRU ID 19 CPU assembly, Intel Core 2 Duo processor T8300 (2.4 GHz) v 8889-CTO, A7x, A9x, AEx, AHx, AJx v 8890-CTO, AQx v 8891-CTO v 8892-CTO v 8893-CTO v 8894-CTO v 8895-CTO, A6x, A8x v 8896-CTO, ADx v 8897-CTO v 8898-CTO v 8899-CTO v 8900-CTO v 8938-CTO v 8939-CTO, A3x 42W7880 R N 19 CPU assembly, Intel Core 2 Duo processor T9300 (2.
Table 42. Parts list—Overall (continued) No. FRU FRU no.
Table 42. Parts list—Overall (continued) No. FRU FRU no. RoHS ID CRU ID 22 Intel Turbo Memory, 1GB v 8889-CTO, 3Fx, 6Gx, 6Hx, 6Px, 6Qx, 6Rx, 6Sx, 72x, A8x, A9x, ACx, ADx, AEx, AFx, AKx, ALx, AMx, ARx, ATx v 8890-CTO, ANx v 8891-CTO v 8892-CTO, 2Tx, 2Xx, 2Zx, 3Lx, 5Vx, 64x v 8893-CTO v 8894-CTO v 8895-CTO, 5Yx, 64x, 66x v 8896-CTO v 8897-CTO v 8898-CTO, 22x, 5Cx v 8899-CTO v 8900-CTO v 8938-CTO v 8939-CTO 42T0907 R ** 24 Keyboard (see “Keyboard” on page 152.
LCD FRUs In ThinkPad T61 and T61p (14.1-inch), there are following types of LCDs. v “14.1-inch XGA TFT” on page 147 v “14.1-inch SXGA+ TFT” on page 149 146 ThinkPad T61 and T61p (14.
14.1-inch XGA TFT Table 43. Parts list—14.1-inch XGA TFT No. FRU FRU no.
Table 43. Parts list—14.1-inch XGA TFT (continued) No. 2 FRU no.
Table 43. Parts list—14.1-inch XGA TFT (continued) No. 8 9 FRU FRU no. RoHS ID CRU ID LCD panel, 14.1-in.
Table 44. Parts list—14.1-inch SXGA+ TFT (continued) No. 150 FRU FRU no.
Table 44. Parts list—14.1-inch SXGA+ TFT (continued) No. 5 6 FRU FRU no.
Keyboard 152 Language P/N (ALPS) P/N P/N (Chicony) (NMB) RoHS ID CRU ID Arabic 42T3212 42T3276 42T3146 R ** Belgian 42T3213 42T3277 42T3147 Brazilian Portuguese 42T3240 42T3304 42T3174 Canadian French (058) 42T3211 42T3275 42T3145 Canadian French (Acnor) 42T3210 42T3274 42T3144 Czech 42T3214 42T3278 42T3148 Danish 42T3215 42T3279 42T3149 Dutch 42T3223 42T3287 42T3157 Finnish, Swedish 42T3230 42T3294 42T3164 French 42T3217 42T3281 42T3151 German 42T3218 42T3
Miscellaneous parts Table 45. Parts list—Miscellaneous parts FRU P/N RoHS ID CRU ID Screw kit (including nylon-coated screws): v M2 × 4 mm (black), bind head (17) v M2 × 2.7 mm (black), flat head (2) v M2 × 2.8 mm (silver), flat head (14) v M2 × 3 mm (silver), small head (15) v M2 × 3.6 mm (gold), flat head (24) v M2 × 5 mm (black), flat head (20) v M2 × 9.5 mm (black), bind head (11) v M2 × 14 mm (black), flat head (10) v M2 × 14 mm HDD security (2) v M2 × 19 mm (black), bind head (2) v M2.
Table 45.
Power cords A ThinkPad power cord for a specific country or region is usually available only in that country or region: Table 47. Parts list—2-pin power cords Region P/N P/N (Longwell) (Volex) RoHS ID CRU ID Argentina v models -CTO, xxY 42T5020 42T5105 R * Brazil v models -CTO, xxP 42T5180 42T5183 Canada, U.S. v models -CTO, xxF, xxL, xxS, xxU 42T5008 42T5093 Japan v models -Exx, Jxx 42T5014 42T5099 Table 48.
Recovery discs Windows XP Professional CDs Windows XP Professional is preinstalled as the operating system in the following models: v 8889-CTO, 28x, 2Fx, 2Hx, 32x, 36x v 8890-CTO v 8891-CTO, 2Gx, 3Ax v 8892-CTO, 67x v 8893-CTO v 8894-CTO v 8895-CTO, 26x, 2Jx, 2Kx, 2Lx, 2Rx, 2Ux, 2Xx, 2Zx, 35x, 37x, 38x, 3Ax, 5Hx, 5Mx, 5Nx, 5Px, 5Sx, 5Ux, 5Wx, 5Xx v 8896-CTO v 8897-CTO, 27x, 2Sx, 2Yx, 36x v 8898-CTO, 2Hx, 5Bx, 5Fx, 5Tx, 6Dx, AFx v 8899-CTO v 8900-CTO v 8938-CTO v 8939-CTO 156 ThinkPad T61 and T61p (14.
Table 49.
Windows Vista Home Basic (32 bit) DVDs Windows Vista Home Basic (32 bit) is preinstalled as the operating system in the following models: v 8889-CTO v 8890-CTO v 8891-CTO, 2Sx v 8892-CTO v 8893-CTO v 8894-CTO v 8895-CTO v 8896-CTO v 8897-CTO, 29x, 2Ax v 8898-CTO v 8899-CTO v 8900-CTO v 8938-CTO, 23x, 3Cx v 8939-CTO Table 50.
Windows Vista Home Premium (32 bit) DVDs Windows Vista Home Premium (32 bit) is preinstalled as the operating system in the following models: v 8889-CTO v 8890-CTO v 8891-CTO, 2Sx v 8892-CTO v 8893-CTO v 8894-CTO v 8895-CTO v 8896-CTO v 8897-CTO v 8898-CTO v 8899-CTO v 8900-CTO v 8938-CTO v 8939-CTO, 2Lx, 6Vx, 6Yx, 6Zx ThinkPad T61 and T61p (14.
Table 51.
Windows Vista Business (32 bit) DVDs Windows Vista Business (32 bit) is preinstalled as the operating system in the following models: v 8889-CTO, 24x, 26x, 2Nx, 2Qx, 2Ux, 3Hx, 3Qx, 3Rx, 3Vx, 3Wx, 5Yx, 5Zx, 69x, 6Ax, 6Bx, 6Cx, 6Dx, 6Ex, 6Fx, 6Gx, 6Hx, 6Lx, 6Mx, 6Nx, 6Px, 6Qx, 6Rx, 6Sx, 6Wx, 6Xx, A4x, A5x, A6x, A7x, A9x, ABx, ACx, ADx, AEx, AFx, AGx, AHx, AJx, AKx v 8890-CTO, 24x, 26x, APx, AQx v 8891-CTO v 8892-CTO, 2Vx, 2Xx, 3Gx v 8893-CTO, 5Ux v 8894-CTO, 5Ux v 8895-CTO, 2Bx, 2Fx, 3Ex, 3Gx, 3Hx, 3Jx, 3Mx,
Table 52.
Windows Vista Business (64 bit) DVDs Windows Vista Business (64 bit) is preinstalled as the operating system in the following models: v 8889-CTO, 22x, 2Ax, 2Bx, 2Cx, 2Dx, 2Mx, 2Px, 2Wx, 2Yx, 3Ex, 3Mx, 3Nx, 3Px, 3Sx, 3Tx, 3Ux, 5Wx, 5Xx, A8x, AAx, AMx v 8890-CTO, ANx v 8891-CTO, 2Ex v 8892-CTO, 2Rx, 2Tx, 2Zx, 3Lx, 5Vx, 64x v 8893-CTO v 8894-CTO v 8895-CTO, 24x, 28x, 2Ex, 2Fx, 3Dx, 3Kx, 3Lx, 3Nx, 3Px, 3Qx, 3Rx, 3Sx, A7x v 8896-CTO v 8897-CTO, 25x, 6Mx v 8898-CTO, 22x, 2Mx, 2Nx, 57x, 58x v 8899-CTO v 8900-CTO v
Windows Vista Ultimate (32 bit) DVDs Windows Vista Ultimate (32 bit) is preinstalled as the operating system in the following models: v 8889-CTO, 23x, 35x, 37x, 39x, 3Cx, 3Dx, 3Fx, 6Jx, 6Kx, 6Tx, 6Ux, 72x, ALx, ARx, ASx, ATx v 8890-CTO v 8891-CTO, 3Bx v 8892-CTO v 8893-CTO v 8894-CTO v 8895-CTO v 8896-CTO v 8897-CTO v 8898-CTO v 8899-CTO v 8900-CTO v 8938-CTO v 8939-CTO Table 54.
Common service tools Table 55. Parts list—Common service tools Tool P/N Screwdriver kit 95F3598 1/4″ drive spinner handle 1650840 1/4″ Sq. to 1/4″ hex torx adapter 93F2838 TR7-TR-10 tamper resistant torx bits 00P6967 Removal tool antenna RF connector 08K7159 USB 2.
166 ThinkPad T61 and T61p (14.
Notices Lenovo may not offer the products, services, or features discussed in this document in all countries. Consult your local Lenovo representative for information on the products and services currently available in your area. Any reference to a Lenovo product, program, or service is not intended to state or imply that only that Lenovo product, program, or service may be used.
Trademarks The following terms are trademarks of Lenovo in the United States, other countries or both: Lenovo Active Protection System Rescue and Recovery ThinkLight ThinkPad ThinkVantage TrackPoint Ultrabay UltraNav The following terms are trademarks of the International Business Machines Corporation in the United States, other countries, or both: IBM (used under license) The following terms are trademarks of the Microsoft group of companies: Windows Windows Vista The following terms are trademarks of Inte
(1P) P/N: 42X3545_04 *42X3545_04*
