ThinkCentre M83, M93/p User Guide Machine Types: 10A0, 10A1, 10A6, 10A7, 10AG, 10AK, 10AL, and 10BE
Note: Before using this information and the product it supports, be sure to read and understand the “Important safety information” on page v and Appendix A “Notices” on page 139. First Edition (June 2013) © Copyright Lenovo 2013. LIMITED AND RESTRICTED RIGHTS NOTICE: If data or software is delivered pursuant a General Services Administration “GSA” contract, use, reproduction, or disclosure is subject to restrictions set forth in Contract No. GS-35F-05925.
Contents Important safety information . . . . . . v Service and upgrades . . . . . . Static electricity prevention . . . . Power cords and power adapters . Extension cords and related devices Plugs and outlets. . . . . . . . External devices . . . . . . . . Heat and product ventilation . . . Operating environment . . . . . Modem safety information . . . . Laser compliance statement . . . Power supply statement . . . . . Cleaning and maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Replacing the secondary hard disk drive. . Installing the solid-state drive . . . . . . Replacing the front fan assembly . . . . Replacing the rear fan assembly . . . . . Replacing the front audio and USB assembly . . . . . . . . . . . . . . Replacing the internal speaker. . . . . . Replacing the thermal sensor . . . . . . Replacing the cover presence switch . . . Replacing the Wi-Fi units . . . . . . . . Installing or removing the rear Wi-Fi antenna Installing or removing the front Wi-Fi antenna . . . . .
Using the documentation and diagnostic program . . . . . . . . . . . . . Calling for service. . . . . . . . . . Using other services . . . . . . . . Purchasing additional services . . . . . . . . . . . . Appendix A. Notices . . . . . . . . . Trademarks . . . . . . . . . . . . . . . . Appendix B. Regulatory information . . . . . . . . . . . . . Export classification notice . . . . . . . Electronic emissions notices . . . . . . Federal Communications Commission Declaration of Conformity . . . . .
iv ThinkCentre M83, M93/p User Guide
Important safety information CAUTION: Before using this manual, be sure to read and understand all the related safety information for this product. Refer to the information in this section and the safety information in the Safety, Warranty, and Setup Guide that you received with this product. Reading and understanding this safety information reduces the risk of personal injury and damage to your product.
or CRU, do not open the static-protective package containing the part until the instructions direct you to install it. When you handle options or CRUs, or perform any work inside the computer, take the following precautions to avoid static-electricity damage: • Limit your movement. Movement can cause static electricity to build up around you. • Always handle components carefully. Handle adapters, memory modules, and other circuit boards by the edges. Never touch exposed circuitry.
Plugs and outlets If a receptacle (power outlet) that you intend to use with your computer equipment appears to be damaged or corroded, do not use the outlet until it is replaced by a qualified electrician. Do not bend or modify the plug. If the plug is damaged, contact the manufacturer to obtain a replacement. Do not share an electrical outlet with other home or commercial appliances that draw large amounts of electricity; otherwise, unstable voltage might damage your computer, data, or attached devices.
For your safety and to maintain optimum computer performance, always follow these basic precautions with your desktop computer: • Keep the cover closed whenever the computer is plugged in. • Regularly inspect the outside of the computer for dust accumulation. • Remove dust from vents and any perforations in the bezel. More frequent cleanings might be required for computers in dusty or high-traffic areas. • Do not restrict or block any ventilation openings.
Laser compliance statement CAUTION: When laser products (such as CD-ROMs, DVD drives, fiber optic devices, or transmitters) are installed, note the following: • Do not remove the covers. Removing the covers of the laser product could result in exposure to hazardous laser radiation. There are no serviceable parts inside the device. • Use of controls or adjustments or performance of procedures other than those specified herein might result in hazardous radiation exposure.
x ThinkCentre M83, M93/p User Guide
Chapter 1. Product overview This chapter provides information about the computer features, specifications, software programs provided by Lenovo, and locations of connectors, components, parts on the system board, and internal drives. Features This section introduces the computer features. The information covers a variety of models.
• Audio line-in connector, audio line-out connector, and microphone connector on the rear panel • Microphone connector and headphone connector on the front panel • Internal speaker (available in some models) Connectivity • 100/1000 Mbps integrated Ethernet controller • PCI Fax modem (available in some models) System management features • Ability to store power-on self-test (POST) hardware test results • Desktop Management Interface (DMI) Desktop Management Interface provides a common path for users to acces
• Wake on Ring Wake on Ring, sometimes referred to as Wake on Modem, is a specification that allows supported computers and devices to resume from sleep or hibernation mode. • Windows Management Instrumentation (WMI) Windows Management Instrumentation is a set of extensions to the Windows Driver Model. It provides an operating system interface through which instrumented components provide information and notification.
• Power-on password (POP), administrator password, and hard disk drive password to deter unauthorized use of your computer • Support for a Kensington-style cable lock • Support for a padlock • Startup sequence control • Startup without keyboard or mouse • Trusted Platform Module (TPM) For more information, see Chapter 4 “Security” on page 29. Preinstalled software programs Your computer is preinstalled with software programs to help you work more easily and securely.
Specifications This section lists the physical specifications for your computer. Dimensions Width: 175 mm (6.89 inches) Height: 414 mm (16.30 inches) Depth: 442 mm (17.40 inches) Weight Maximum configuration as shipped: 11.2 kg (24.
Note: If a program icon in the Lenovo ThinkVantage Tools program navigation window is dimmed, it indicates that you need to install the program manually. To install the program manually, double-click the program icon. Then, follow the instructions on the screen. When the installation process completes, the program icon will be activated. Table 1.
Table 2. Programs in Control Panel (continued) Program Control Panel section Green text in Control Panel System Update System and Security Lenovo - Update and Drivers View Management Utility System and Security Lenovo View Management Utility Note: Depending on your computer model, some of the programs might not be available.
different devices such as personal computers, smart phones, or tablets. For more information about the Lenovo Cloud Storage program, go to http://www.lenovo.com/cloud. • Lenovo Companion Through the Lenovo Companion program, you can get the information about the accessories for your computer, view blogs and articles about your computer, and check for other recommended programs.
The SimpleTap program provides you with a quick way to customize some basic computer settings such as muting the speakers, adjusting the volume, locking the computer operating system, launching a program, opening a Web page, opening a file, and so on. You also can use the SimpleTap program to access the Lenovo App Shop, from which you can download various applications and computer software.
Locating connectors, controls, and indicators on the front of your computer Figure 1 “Front connector, control, and indicator locations” on page 10 shows the locations of the connectors, controls, and indicators on the front of your computer. 1 2 Figure 1. Front connector, control, and indicator locations 1 Hard disk drive activity indicator 5 USB 3.0 connector (USB port 1) 2 Power indicator 6 Headphone connector 3 Power button 7 Microphone connector 4 Optical drive eject/close button 8 USB 3.
® ® HDMI ® ® 5 6 7 8 5 6 7 8 3 4 3 4 Figure 2. ThinkCentre M93/p rear connector locations 1 Power cord connector 11 Audio line-out connector 2 Serial port 1 12 Audio line-in connector 3 VGA monitor connector 13 PCI Express x16 graphics card slot 4 DisplayPort connectors (2) 14 PCI Express x1 card slot 5 PS/2 keyboard and mouse connectors (optional) 15 PCI Express card slot (physical link width x16; negotiable link width x4, x1) 6 USB 3.
® ® HDMI ® ® 5 6 7 8 5 6 7 8 3 4 3 4 Figure 3. ThinkCentre M83 rear connector locations 1 Power cord connector 10 Microphone connector 2 Serial port 1 11 Audio line-out connector 3 VGA monitor connector 12 Audio line-in connector 4 DisplayPort connectors (2) 13 PCI Express x16 graphics card slot 5 PS/2 keyboard and mouse connectors (optional) 14 PCI Express x1 card slot 6 USB 3.
Connector Description Ethernet connector Used to attach an Ethernet cable for a local area network (LAN). Note: To operate the computer within FCC Class B limits, use a Category 5 Ethernet cable. Microphone connector Used to attach a microphone to your computer when you want to record sound or if you use speech-recognition software. PS/2 keyboard connector (optional) Used to attach a keyboard that uses a PS/2 keyboard connector.
Locating components Figure 4 “Component locations” on page 14 shows the locations of the various components in your computer. To remove the computer cover, see “Removing the computer cover” on page 36. Figure 4.
30 Figure 5.
29 28 27 26 14 25 15 24 16 23 22 21 20 19 18 17 Figure 6.
Locating internal drives Internal drives are devices that your computer uses to read and store data. You can add drives to your computer to increase storage capacity and enable your computer to read other types of media. Internal drives are installed in bays. When installing or replacing an internal drive, it is important to note the type and size of the drive that you can install or replace in each bay and correctly connect the cables to the drive installed.
Machine type and model label The machine type and model label identifies your computer. When you contact Lenovo for help, the machine type and model information helps support technicians to identify your computer and provide faster service. ® The following is a sample of the machine type and model label. 44 3 3 3 4 5 5 ® I 5 666 777 8 88 HD M Machine Type: XXXX Model Number: XXX Figure 8.
Chapter 2. Using your computer This chapter provides information on using some of the computer components. Frequently asked questions The following are a few tips that will help you optimize the use of your computer. Can I get my user guide in another language? The user guide is available in various languages on the Lenovo Support Web site at: http://www.lenovo.com/ThinkCentreUserGuides Where are my recovery discs? Lenovo provides a program that enables you to create recovery discs.
Using the keyboard Depending on your model, your computer comes with either a standard keyboard or a fingerprint reader keyboard. The Microsoft Windows shortcut keys are provided on both keyboard types.
Using the wheel mouse The wheel mouse has the following controls: 1 Primary mouse button Use this button to select or start a program or menu item. 2 Wheel Use the wheel to control the scrolling action of the mouse. The direction in which you rotate the wheel controls the direction of the scrolling action. 3 Secondary mouse button Use this button to display a menu for the active program, icon, or object.
1. From the Windows desktop, click Start ➙ Control Panel ➙ Appearance and Personalization. 2. In the Taskbar and Start Menu section, click Customize icons on the taskbar. 3. Click Turn system icons on or off and change the volume behaviors from Off to On. 4. Click OK to save the new settings. To add the volume icon to the taskbar on the Windows 8 operating system, do the following: 1. Open Control Panel, and click Appearance and Personalization. 2.
• Do not write or stick paper on the disc. • Do not scratch or mark the disc. • Do not place or store the disc in direct sunlight. • Do not use benzene, thinners, or other cleaners to clean the disc. • Do not drop or bend the disc. • Do not insert damaged discs into the drive. Warped, scratched, or dirty discs can damage the drive. Playing a CD or DVD If your computer comes with a DVD drive, you can listen to audio CDs or watch DVD movies. To play a CD or DVD, do the following: 1.
24 ThinkCentre M83, M93/p User Guide
Chapter 3. You and your computer This chapter provides information about accessibility, comfort, and relocating your computer to other countries or regions. Accessibility and comfort Good ergonomic practice is important to get the most from your personal computer and to avoid discomfort. Arrange your workplace and the equipment you use to suit your individual needs and the kind of work that you perform. In addition, use healthy work habits to maximize your performance and comfort while using your computer.
Adjust the monitor so the top of the screen is at, or slightly below, eye level. Place the monitor at a comfortable viewing distance, usually 51 to 61 cm (20 to 24 inches), and position it so you can view it without having to twist your body. Also, position other equipment you use regularly, such as the telephone or a mouse, within easy reach. Glare and lighting Position the monitor to minimize glare and reflections from overhead lights, windows, and other light sources.
Registering your computer When you register your computer, information is entered into a database, which enables Lenovo to contact you in case of a recall or other severe problem. After you register your computer with Lenovo, you will receive quicker service when you call Lenovo for help. In addition, some locations offer extended privileges and services to registered users. To register your computer with Lenovo, do one of the following: • Go to http://www.lenovo.
28 ThinkCentre M83, M93/p User Guide
Chapter 4. Security This chapter provides information about how to protect your computer from theft and unauthorized use. Security features The following security features are available on your computer: • Computrace Agent software embedded in firmware The Computrace Agent software is an IT asset management and computer theft recovery solution. The software detects if changes have been made on the computer, such as hardware, software, or the computer call-in location.
Locking the computer cover Locking the computer cover helps prevent unauthorized people from gaining access to the inside of your computer. Your computer comes with a padlock loop so that the computer cover cannot be removed when a padlock is installed. Figure 9.
Attaching a Kensington-style cable lock You can use a Kensington-style cable lock to secure your computer to a desk, table, or other non-permanent fixture. The cable lock attaches to the security-lock slot at the rear of your computer and is operated with a key or combination depending on the type selected. The cable lock also locks the buttons used to open the computer cover. This is the same type of lock used with many notebook computers.
Attaching a cable lock You can use a cable lock to secure devices, such as the keyboard and the mouse, by locking the device cables to your computer. The cable lock attaches to the cable-lock slots on the rear of your computer. See “Locating connectors on the rear of your computer” on page 10. To install a cable lock, do the following: 1. Insert the clip 1 into the cable-lock slot 4 . 2. Pull the cables you want to lock through the dents in the cable lock. 3.
• Hard Disk Password: Setting a Hard Disk Password prevents unauthorized access to the data on the hard disk drive. When a Hard Disk Password is set, you are prompted to type a valid password each time you try to access the hard disk drive. For more information, see “Hard Disk Password” on page 106. • Administrator Password: Setting an Administrator Password deters unauthorized users from changing configuration settings.
Lenovo provides a full version of antivirus software on your computer with a free 30-day subscription. After 30 days, you must renew the license to continue receiving the antivirus software updates. Note: Virus definition files must be kept up-to-date to guard against new viruses. For more information about how to use your antivirus software, refer to the help system of your antivirus software.
Chapter 5. Installing or replacing hardware This chapter provides instructions on how to install or replace hardware for your computer. Note: Depending on the model, your computer might look slightly different from the illustrations in this chapter. Handling static-sensitive devices Do not open the static-protective package containing the new part until the defective part has been removed from the computer and you are ready to install the new part.
Removing the computer cover Attention: Do not open your computer or attempt any repair before reading and understanding the “Important safety information” on page v. This section provides instructions on how to remove the computer cover. CAUTION: Turn off the computer and wait three to five minutes to let the computer cool before removing the computer cover. To remove the computer cover, do the following: 1. Remove any media from the drives and turn off all attached devices and the computer. 2.
6. Press the cover-release button on the side of the computer and slide the cover to the rear of the computer to remove the cover. ® HDMI ® 5 5 6 6 7 7 88 3 3 4 4 Figure 12. Removing the computer cover Removing and reinstalling the front bezel Attention: Do not open your computer or attempt any repair before reading and understanding the “Important safety information” on page v. This section provides instructions on how to remove and reinstall the front bezel.
3. Remove the front bezel by releasing the three plastic tabs on the left side and pivoting the front bezel outward. Figure 13. Removing the front bezel 4. To reinstall the front bezel, align the three plastic tabs on the right side of the front bezel with the corresponding holes in the chassis. Then, pivot the front bezel inwards until it snaps into position on the left side. What to do next: • To work with another piece of hardware, go to the appropriate section.
3. At the rear of the computer, press the release button 1 to open the card latch 2 . Figure 14. Opening the PCI card latch Chapter 5.
4. Depending on whether you are installing or replacing a PCI card, do one of the following: • If you are installing a PCI card, remove the appropriate metal slot cover. • If you are replacing an old PCI card, grasp the old card that is currently installed and gently pull it out of the slot. Figure 15. Removing a PCI card Notes: – The card fits tightly into the card slot. If necessary, alternate moving each side of the card a small and equal amount until the card is removed from the slot.
6. Install the new card into the appropriate slot on the system board. See “Locating parts on the system board” on page 14. Note: If you are installing a PCI Express x16 graphics card, make sure that the memory slot retaining clips are closed before you install the graphics card. 7. Pivot the card latch to the closed position to secure the PCI card. Figure 16. Installing a PCI card What to do next: • To work with another piece of hardware, go to the appropriate section.
UDIMM DIMM 1 DIMM 2 DIMM 3 DIMM 4 One UDIMM X Two UDIMMs X, 1 X, 2 X, 2 Three UDIMMs X, 3 X, 1 Four UDIMMs X, 3 X, 1 X, 4 X, 2 To install or replace a memory module, do the following: 1. Remove all media from the drives and turn off all attached devices and the computer. Then, disconnect all power cords from electrical outlets and disconnect all cables that are connected to the computer. 2. Remove the computer cover. See “Removing the computer cover” on page 36. 3.
• If you are installing a memory module, open the retaining clips of the memory slot into which you want to install the memory module. Figure 18. Opening the retaining clips 7. Position the new memory module over the memory slot. Make sure that the notch 1 on the memory module aligns correctly with the slot key 2 on the system board. Push the memory module straight down into the slot until the retaining clips close. Figure 19. Installing a memory module 8.
1. Remove all media from the drives and turn off all attached devices and the computer. Then, disconnect all power cords from electrical outlets and disconnect all cables that are connected to the computer. 2. Remove the computer cover. See “Removing the computer cover” on page 36. 3. Remove the front bezel. See “Removing and reinstalling the front bezel” on page 37. 4.
6. Slide the new optical drive into the drive bay from the front of the computer until the optical drive snaps into position. Figure 22. Installing the optical drive 7. Connect the signal cable and the power cable to the new optical drive. Figure 23. Connecting the optical drive 8. Reinstall the front bezel. See “Removing and reinstalling the front bezel” on page 37. What to do next: • To work with another piece of hardware, go to the appropriate section.
This section provides instructions on how to install or replace the card reader. Note: The card reader is only available in some models. Installing the card reader To install the card reader, do the following: 1. Remove all media from the drives and turn off all attached devices and the computer. Then, disconnect all power cords from electrical outlets and disconnect all cables that are connected to the computer. 2. Remove the computer cover. See “Removing the computer cover” on page 36. 3.
7. Slide the new card reader with retainer into the card reader drive bay until it snaps into position. Figure 26. Installing the card reader 8. Connect the card reader cable to the front USB connector 2 on the system board. See “Locating parts on the system board” on page 14. 9. Locate the protective cover for the card reader drive bay on the front bezel. Remove the protective cover by pressing the small tabs 1 to the left, and then pulling the tabs to completely disengage the cover from the front bezel.
What to do next: • To work with another piece of hardware, go to the appropriate section. • To complete the installation or replacement, go to “Completing the parts replacement” on page 95. Replacing the card reader Attention: Do not open your computer or attempt any repair before reading and understanding the “Important safety information” on page v. To replace the card reader, do the following: 1. Remove all media from the drives and turn off all attached devices and the computer.
7. Remove the card reader retainer from the old card reader and install it on the side of the new card reader. Figure 29. Installing the card reader retainer 8. Slide the new card reader with retainer into the drive bay until it snaps into position. Figure 30. Installing the card reader 9. Reconnect the card reader cable to the front USB connector 2 on the system board. See “Locating parts on the system board” on page 14. 10. Reinstall the front bezel.
Installing the front USB assembly Attention: Do not open your computer or attempt any repair before reading and understanding the “Important safety information” on page v. To install the front USB assembly, do the following: 1. Remove all media from the drives and turn off all attached devices and the computer. Then, disconnect all power cords from electrical outlets and disconnect all cables that are connected to the computer. 2. Remove the computer cover. See “Removing the computer cover” on page 36. 3.
7. Slide the new front USB assembly with retainer into the card reader drive bay until it snaps into position. Figure 33. Installing the front USB assembly 8. Connect the front USB assembly cable to the front USB connector 2 on the system board. See “Locating parts on the system board” on page 14. 9. Locate the protective cover for the card reader drive bay on the front bezel.
What to do next: • To work with another piece of hardware, go to the appropriate section. • To complete the installation or replacement, go to “Completing the parts replacement” on page 95. Replacing the front USB assembly Attention: Do not open your computer or attempt any repair before reading and understanding the “Important safety information” on page v. To replace the front USB assembly, do the following: 1. Remove all media from the drives and turn off all attached devices and the computer.
7. Remove the card reader retainer from the old front USB assembly and install it on the side of the new front USB assembly. Figure 36. Installing the card reader retainer 8. Slide the new front USB assembly with retainer into the card reader drive bay until it snaps into position. Figure 37. Installing the front USB assembly 9. Connect the cable of the new front USB assembly to the front USB connector 2 on the system board. See “Locating parts on the system board” on page 14. 10.
Your computer has a special type of memory that maintains the date, time, and settings for built-in features, such as parallel-port assignments (configuration). A battery keeps this information active when you turn off the computer. The battery normally requires no charging or maintenance throughout its life; however, no battery lasts forever. If the battery fails, the date, time, and configuration information (including passwords) are lost. An error message is displayed when you turn on the computer.
Replacing the power supply assembly Attention: Do not open your computer or attempt any repair before reading and understanding the “Important safety information” on page v. This section provides instructions on how to replace the power supply assembly. Although there are no moving parts in your computer after the power cord has been disconnected, the following warnings are required for your safety and proper Underwriters Laboratories (UL) certification. CAUTION: Hazardous moving parts.
® 5. Lay the computer on its side and remove the four screws at the rear of the chassis that secure the power supply assembly. 44 3 3 3 4 5 5 ® I 5 666 777 8 88 HD M Figure 40. Removing the screws for the power supply assembly 6. Slide the power supply assembly to the front of the computer, and then lift it out of the chassis. 7. Ensure that the new power supply assembly is the correct replacement. 8.
To replace the heat sink and fan assembly, do the following: 1. Remove all media from the drives and turn off all attached devices and the computer. Then, disconnect all power cords from electrical outlets and disconnect all cables that are connected to the computer. 2. Remove the computer cover. See “Removing the computer cover” on page 36. 3. Lay the computer on its side for easier access to the system board. 4. Locate the heat sink and fan assembly. See “Locating parts on the system board” on page 14. 5.
9. Follow the following sequence to install the four screws to secure the new heat sink and fan assembly. Do not over-tighten the screws. a. Partially tighten screw 1 , then fully tighten screw 2 , and then fully tighten screw 1 . b. Partially tighten screw 3 , then fully tighten screw 4 , and then fully tighten screw 3 . 10. Connect the heat sink and fan assembly cable to the microprocessor fan connector on the system board. See “Locating parts on the system board” on page 14.
6. Lift the small handle 1 and open the retainer 2 to access the microprocessor 3 . Figure 42. Accessing the microprocessor 7. Lift the microprocessor straight up and out of the microprocessor socket. Figure 43. Removing the microprocessor Notes: • Your microprocessor and socket might look different from the one illustrated. • Touch only the edges of the microprocessor. Do not touch the gold contacts on the bottom. • Do not drop anything onto the microprocessor socket while it is exposed.
Note: The small triangle 3 on one corner of the new microprocessor is the microprocessor orientation indicator. The new microprocessor is in the correct orientation when this indicator faces the beveled corner 4 of the microprocessor socket. Figure 44. Installing the microprocessor 11. Close the microprocessor retainer and lock it into position with the small handle to secure the new microprocessor in the socket. 12. Reinstall the heat sink and fan assembly.
1. Insert the mSATA solid-state drive into the mini PCI Express slot on the storage converter, and then press the mSATA solid-state drive downward. Figure 45. Installing the mSATA solid-state drive into the storage converter 2. Install the two screws to secure the mSATA solid-state drive to the storage converter. Figure 46. Installing the screws that secure the mSATA solid-state drive Chapter 5.
3. Slide the mSATA solid-state drive storage converter into the card reader drive bay until it snaps into position. Figure 47. Installing the mSATA solid-state drive 4. Connect the signal cable and the power cable to the mSATA solid-state drive. What to do next: • To work with another piece of hardware, go to the appropriate section. • To complete the installation or replacement, go to “Completing the parts replacement” on page 95.
6. Press the blue retaining clip to remove the mSATA solid-state drive storage converter out of the chassis. Figure 48. Removing the mSATA solid-state drive storage converter 7. Remove the two screws that secure the mSATA solid-state drive from the storage converter. Figure 49. Removing the screws that secure the mSATA solid-state drive Chapter 5.
8. Pull the mSATA solid-state drive from the mini PCI Express slot on the storage converter. Figure 50. Removing the mSATA solid-state drive 9. To install a new mSATA solid-state drive, insert the mSATA solid-state drive into the mini PCI Express slot on the storage converter, and then press the mSATA solid-state drive downward. Figure 51.
10. Install the two screws to secure the mSATA solid-state drive to the storage converter. Figure 52. Installing the screws that secure the mSATA solid-state drive 11. Slide the mSATA solid-state drive storage converter into the card reader drive bay until it snaps into position. Figure 53. Installing the mSATA solid-state drive 12. Connect the signal cable and the power cable to the mSATA solid-state drive. What to do next: • To work with another piece of hardware, go to the appropriate section.
Replacing the primary hard disk drive Attention: Do not open your computer or attempt any repair before reading and understanding the “Important safety information” on page v. This section provides instructions on how to replace the primary hard disk drive. Note: Depending on your model type, your computer might come with a 2.5-inch solid-state drive. To install the solid-state drive, see “Installing the solid-state drive” on page 70 To replace the primary hard disk drive, do the following: 1.
7. To install a new hard disk drive into the blue bracket, flex the bracket and align pin 1 , pin 2 , pin 3 , and pin 4 on the bracket with the corresponding holes in the hard disk drive. Do not touch the circuit board 5 on the bottom of the hard disk drive. Figure 55. Installing the hard disk drive into the bracket 8. Slide the new hard disk drive into the bracket until it snaps into position. Figure 56. Installing the primary hard disk drive 9.
Replacing the secondary hard disk drive Attention: Do not open your computer or attempt any repair before reading and understanding the “Important safety information” on page v. Note: Your computer comes with a secondary hard disk drive bay for installing or replacing a secondary 3.5-inch hard disk drive or a 2.5-inch solid-state drive. To install the solid-state drive, see “Installing the solid-state drive” on page 70 This section provides instructions on how to replace the secondary hard disk drive.
7. To install a new hard disk drive into the blue bracket, flex the bracket and align pin 1 , pin 2 , pin 3 , and pin 4 on the bracket with the corresponding holes in the hard disk drive. Do not touch the circuit board 5 on the bottom of the hard disk drive. Figure 58. Installing the hard disk drive into the bracket 8. Slide the new hard disk drive into the hard disk bracket until it snaps into position. Figure 59. Installing the secondary hard disk drive 9.
Installing the solid-state drive Attention: Do not open your computer or attempt any repair before reading and understanding the “Important safety information” on page v. This section provides instructions on how to install the 2.5-inch solid-state drive. To install the solid-state drive, do the following: 1. Install the solid-state drive into the storage converter. Then, install the four screws to secure the solid-state drive to the storage converter. Figure 60.
2. To install the solid-state drive with the storage converter into the 3.5-inch hard disk drive bracket, flex the bracket and align pin 1 , pin 2 , pin 3 , and pin 4 on the bracket with the corresponding holes in the storage converter. Figure 61. Installing the solid-state drive with the storage converter into the hard disk drive bracket 3. Install the solid-state drive into the desired hard disk drive bay.
4. The front fan assembly is attached to the chassis by four rubber mounts. Remove the front fan assembly by breaking or cutting the rubber mounts and gently pulling the front fan assembly out of the chassis. Note: The new front fan assembly will have four new rubber mounts attached. Figure 62. Removing the front fan assembly 5. Remove the front bezel. See “Removing and reinstalling the front bezel” on page 37. 6.
7. Pull the tips of the rubber mounts until the front fan assembly is secured in place. Figure 63. Installing the front fan assembly 8. Connect the front fan assembly cable to the power fan connector on the system board. 9. Reinstall the front bezel. See “Removing and reinstalling the front bezel” on page 37 What to do next: • To work with another piece of hardware, go to the appropriate section. • To complete the installation or replacement, go to “Completing the parts replacement” on page 95.
5. The rear fan assembly is attached to the chassis by four rubber mounts. Remove the rear fan assembly by breaking or cutting the rubber mounts and gently pulling the rear fan assembly out of the chassis. Note: The new rear fan assembly will have four new rubber mounts attached. Figure 64. Removing the rear fan assembly 6. Install the new rear fan assembly by aligning the new rubber mounts with the corresponding holes in the chassis and push the rubber mounts through the holes.
7. Pull on the tips of the rubber mounts until the rear fan assembly is secured in place. Figure 65. Installing the rear fan assembly 8. Connect the rear fan assembly cable to the system fan connector on the system board. What to do next: • To work with another piece of hardware, go to the appropriate section. • To complete the installation or replacement, go to “Completing the parts replacement” on page 95.
4. Locate the front audio and USB assembly. See “Locating components” on page 14. 5. Note the cable routing and connections. Then, disconnect the front audio and USB assembly cables from the system board. 6. Remove the screw that secures the front audio and USB assembly. Then, remove the front audio and USB assembly from the chassis. Figure 66.
7. Route the cables of the new front audio and USB assembly through the corresponding square hole in the front of the chassis. Then position the new front audio and USB assembly on the chassis as shown. Figure 67. Installing the front audio and USB assembly Chapter 5.
8. Install the screw to secure the new front audio and USB assembly in place. Figure 68. Installing the screw to secure the front audio and USB assembly 9. Connect the cables of the new front audio and USB assembly to the front audio connector and the front USB connector 1 on the system board. See “Locating parts on the system board” on page 14. 10. Reinstall the front bezel. See “Removing and reinstalling the front bezel” on page 37.
5. Push the metal tab 1 on the right side of the internal speaker and slide the internal speaker toward the right to completely remove it from the chassis. Figure 69. Removing the old internal speaker Chapter 5.
6. Position the new internal speaker into the four metal clips 1 and push the internal speaker toward the left until it is secured in place. Figure 70. Installing a new internal speaker 7. Connect the internal speaker cable to the system board. See “Locating parts on the system board” on page 14. What to do next: • To work with another piece of hardware, go to the appropriate section. • To complete the installation or replacement, go to “Completing the parts replacement” on page 95.
6. From inside the chassis, pivot the upper retaining clip 1 that secures the plastic holder of the thermal sensor downward and then push the clip outward to release the clip. Then disengage the plastic holder holding the thermal sensor from the chassis. Figure 71. Removing the thermal sensor 7. Pull the entire thermal sensor out of the chassis. Chapter 5.
8. Insert the connector and cable of the new thermal sensor into the lower hole 1 in the chassis. Then align the two tabs on the plastic holder holding the thermal sensor with the two holes 1 and 2 in the chassis, and push the plastic holder until it snaps into position. Figure 72. Installing the new thermal sensor 9. Reconnect the thermal sensor cable to the system board. See “Locating parts on the system board” on page 14. 10. Reinstall the front bezel.
5. Remove the screw that secures the cover presence switch and remove the cover presence switch from the chassis. Figure 73. Removing the cover presence switch Chapter 5.
6. Position the new cover presence switch so that the screw hole in the cover presence switch is aligned with the corresponding hole in the chassis. Then install the screw to secure the cover presence switch to the chassis. Figure 74. Installing the new cover presence switch 7. Reconnect the cover presence switch cable to the system board. See “Locating parts on the system board” on page 14. 8. Reinstall the front bezel. See “Removing and reinstalling the front bezel” on page 37.
Removing the Wi-Fi adapter card To remove a Wi-Fi adapter card, do the following: 1. Turn off the computer and disconnect all power cords from electrical outlets. 2. Remove the computer cover. See “Removing the computer cover” on page 36. 3. If your computer comes with a Wi-Fi card module that supports the Bluetooth function, disconnect the Bluetooth cable from the Wi-Fi adapter card. Figure 75.
4. At the rear of the computer, press the release button 1 to open the PCI card latch 2 . Figure 76.
5. Grasp the Wi-Fi adapter card that is currently installed and gently pull it out of the slot. Figure 77. Removing the Wi-Fi adapter card Note: The card fits tightly into the card slot. If necessary, alternate moving each side of the card a small amount until it is removed from the card slot. Removing the Wi-Fi card module To remove the Wi-Fi card module, do the following: 1.
2. Remove the two screws that secure the Wi-Fi card module to the Wi-Fi adapter card. Figure 79. Removing the screws that secure the Wi-Fi card module 3. Pull the Wi-Fi card module out of the mini PCI Express slot to remove it from the Wi-Fi adapter card. Figure 80.
1. Insert the Wi-Fi card module into the mini PCI Express slot, and then install the two screws to secure the Wi-Fi card module to the Wi-Fi adapter card. Figure 81. Installing the Wi-Fi card module Figure 82. Installing the screws that secure the Wi-Fi card module Chapter 5.
2. Connect the front antenna cable and rear antenna cable to the Wi-Fi card module. Figure 83. Installing the Wi-Fi antenna cables 3. Install the Wi-Fi adapter card into the PCI Express x1 slot on the system board. See “Locating parts on the system board” on page 14. 4. If the installed Wi-Fi card module supports the Bluetooth function, use a Bluetooth cable to connect the Bluetooth connector on the Wi-Fi adapter card to the front USB connector on the system board. 5.
What to do next: • To work with another piece of hardware, go to the appropriate section. • To complete the installation or replacement, go to “Completing the parts replacement” on page 95. Installing or removing the rear Wi-Fi antenna Attention: Do not open your computer or attempt any repair before reading and understanding the “Important safety information” on page v. This section provides instructions on how to install or remove the rear Wi-Fi antenna.
Removing the rear Wi-Fi antenna To remove the rear Wi-Fi antenna, do the following: 1. Remove all media from the drives and turn off all attached devices and the computer. Then, disconnect all power cords from electrical outlets and disconnect all cables that are connected to the computer. 2. Remove the computer cover. See “Removing the computer cover” on page 36. 3. Straighten the rear Wi-Fi antenna so that it can be more easily twisted. 4.
3. Remove the front bezel. See “Removing and reinstalling the front bezel” on page 37. 4. Peel off the paper that protects the stickers on the front antenna. Figure 87. Peeling off the paper that protects the stickers 5. Stick the front antenna to the front panel as shown. Then insert the front antenna cable through the hole in the front panel. Figure 88. Installing the front Wi-Fi antenna Chapter 5.
6. Connect the front antenna cable to the Wi-Fi card module. What to do next: • To work with another piece of hardware, go to the appropriate section. • To complete the installation or replacement, go to “Completing the parts replacement” on page 95. Removing the front Wi-Fi antenna To remove the front Wi-Fi antenna, do the following: 1. Remove all media from the drives and turn off all attached devices and the computer.
To replace the keyboard or mouse, do the following: 1. Disconnect the old keyboard cable or mouse cable from the computer. 2. Connect a new keyboard or mouse to one of the USB connectors on the computer. Depending on where you want to connect the new keyboard or mouse, see “Locating connectors, controls, and indicators on the front of your computer” on page 10 or “Locating connectors on the rear of your computer” on page 10. Figure 90.
4. Position the computer cover on the chassis so that the rail guides on the bottom of the computer cover engage the rails on the chassis. Then, push the cover to the front of the computer until it snaps into position. ® HDMI ® 5 5 6 6 7 7 8 8 3 3 4 4 Figure 91. Reinstalling the computer cover 5. Install the screws to secure the computer cover. 6. If there is an integrated cable lock available, lock the computer. See “Attaching a Kensington-style cable lock” on page 31. 7.
Chapter 6. Recovery information This chapter provides information about the recovery solutions provided by Lenovo.
Creating recovery media This section provides instructions on how to create recovery media. Note: On the Windows 7 operating system, you can create recovery media using discs or external USB storage devices. To create recovery media on the Windows 7 operating system, click Start ➙ All Programs ➙ Lenovo ThinkVantage Tools ➙ Factory Recovery Disks. Then, follow the instructions on the screen. Using recovery media This section provides instructions on how to use recovery media.
1. From the Windows desktop, click Start ➙ All Programs ➙ Lenovo ThinkVantage Tools ➙ Enhanced Backup and Restore. The Rescue and Recovery program opens. 2. In the Rescue and Recovery main window, click the Launch advanced Rescue and Recovery arrow. 3. Click Back up your hard drive and select backup operation options. Then, follow the instructions on the screen to complete the backup operation.
2. Turn on your computer. When you see the logo screen, press Enter, and then press F11 to enter the Rescue and Recovery workspace. 3. If you have set a Rescue and Recovery password, type your password when prompted. The Rescue and Recovery workspace opens after a short delay. Note: If the Rescue and Recovery workspace fails to open, see “Solving recovery problems” on page 102. 4.
1. Attach the USB hard disk drive to one of the USB connectors on your computer. 2. Repeatedly press and release the F12 key when turning on the computer. When the Please select boot device window opens, release the F12 key. 3. In the Please select boot device window, select the USB hard disk drive as the first boot device and press Enter. The rescue medium starts. When the rescue medium starts, the Rescue and Recovery workspace opens.
Note: If you need updated device drivers, see “Getting the latest device drivers for your computer” on page 113 for more information. Reinstalling software programs If a software program you installed on your computer is not working correctly, you might need to remove and reinstall it. Reinstalling overwrites the existing programs files and usually fixes any problems that you might have had with that program. To remove a program in your system, see Microsoft Windows help system for detailed information.
It is important to create a rescue medium and a set of recovery media as early as possible and store them in a safe place for future use. Recovery information for the Windows 8 operating system This section provides information about the recovery solutions provided on computers preinstalled with the Windows 8 operating system.
104 ThinkCentre M83, M93/p User Guide
Chapter 7. Using the Setup Utility program The Setup Utility program is used to view and change the configuration settings of your computer, regardless of which operating system you are using. However, the operating system settings might override any similar settings in the Setup Utility program. Starting the Setup Utility program To start the Setup Utility program, do the following: 1. Make sure your computer is turned off. 2. Repeatedly press and release the F1 key when turning on the computer.
• Power-On Password • Administrator Password • Hard Disk Password You do not have to set any passwords to use your computer. However, using passwords improves computing security. If you decide to set any passwords, read the following sections. Password considerations A password can be any combination of up to 64 alphabetic and numeric characters. For security reasons, it is recommended to use a strong password that cannot be easily compromised.
1. Start the Setup Utility program. See “Starting the Setup Utility program” on page 105. 2. From the Setup Utility program main menu, select Security. 3. Depending on the password type, select Set Power-On Password, Set Administrator Password, or Hard Disk Password. 4. Follow the instructions on the right side of the screen to set, change, or delete a password. Note: A password can be any combination of up to 64 alphabetic and numeric characters.
Selecting a startup device If your computer does not start up from a device such as the disc or hard disk drive as expected, do one of the following to select the startup device you want. Selecting a temporary startup device Use this procedure to select a temporary startup device. Note: Not all discs and hard disk drives are bootable. 1. Turn off your computer. 2. Repeatedly press and release the F12 key when turning on the computer. When the Please select boot device window displays, release the F12 key.
1. Start the Setup Utility program. 2. From the Setup Utility program main menu, select Power ➙ Automatic Power On, and press Enter. 3. Select Wake Up on Alarm and press Enter. Then follow the instructions on the screen. 4. Press F10 to save changes and exit the Setup Utility program. Press Enter when prompted to confirm the exit. • Enabling the after power loss feature The after power loss feature enables your computer to wake up when the power supply resumes after a sudden loss of electricity.
2. From the Setup Utility program main menu, select Power. 3. Select Intelligent Cooling Engine (ICE). The Intelligent Cooling Engine (ICE) window is displayed. 4. Select ICE Thermal Alert. The ICE Thermal Alert window is displayed. 5. Select Enabled or Disabled as desired. 6. Press F10 to save changes and exit the Setup Utility program. See “Exiting the Setup Utility program” on page 110.
Chapter 8. Updating system programs This chapter provides information about updating the POST and BIOS, and how to recover from a POST and BIOS update failure. Using system programs System programs are the basic layer of software built into your computer. System programs include the POST, the BIOS, and the Setup Utility program. The POST is a set of tests and procedures that are performed each time you turn on your computer.
Updating (flashing) the BIOS from your operating system Note: Because Lenovo makes constant improvements to its Web sites, the Web page contents are subject to change without notice, including the contents referenced in the following procedure. To update (flash) the BIOS from your operating system, do the following: 1. Go to http://www.lenovo.com/support. 2. Click Download Drivers & Software. 3. Click Use Quick Path. 4.
Chapter 9. Preventing problems This chapter provides information that can help you avoid common problems and keep your computer running smoothly. Keeping your computer current In some situations you may find it necessary to have the most current software programs, device drivers, or operating system. This section explains how to get the latest updates for your computer.
Using System Update The System Update program helps you keep the software on your computer up-to-date. Update packages are stored on Lenovo servers and can be downloaded from the Lenovo Support Web site. Update packages can contain applications, device drivers, BIOS flashes, or software updates.
Cleaning your computer It is a good practice to clean your computer periodically to protect the surfaces and ensure trouble-free operation. CAUTION: Be sure to turn off the computer and monitor power buttons before cleaning the computer and monitor screen. Computer Use only mild cleaning solutions and a damp cloth to clean the painted surfaces of the computer. Keyboard To clean your computer keyboard, do the following: 1. Apply some isopropyl rubbing alcohol to a soft, dust-free cloth. 2.
Many computer supply stores carry the special cleaning fluids for displays. Use cleaning fluids developed for LCD displays only. First apply the fluid to a lint-free, soft cloth, then clean the LCD display. Some computer supply stores carry pre-moistened towelettes for LCD maintenance. Cleaning a glass-screen surface To clean a glass-screen surface, wipe it gently with a soft, dry cloth, or blow on the screen to remove grit and other loose particles.
Chapter 10. Troubleshooting and diagnostics This chapter provides information about diagnosing and troubleshooting computer problems. If your computer problem is not described here, see Chapter 11 “Getting information, help, and service” on page 135 for additional troubleshooting resources. Basic troubleshooting The following table provides information to help you troubleshoot your computer problems. Note: If you cannot correct the problem, have the computer serviced.
Symptom Action The operating system does not start. Verify that: The computer beeps multiple times before the operating system starts. Verify that no keys are stuck. • The startup sequence includes the device where the operating system resides. Usually, the operating system is on the hard disk drive. For more information, see “Selecting a startup device” on page 108.
1. Remove the new hardware option or software. If you must remove the computer cover to remove a hardware option, make sure you review and follow the electrical safety information provided with your computer. For your safety, do not operate the computer with the cover removed. 2. Run the diagnostic program to ensure your computer is operating correctly. 3. Reinstall the new hardware option or software following the manufacturer's instructions.
Note: When external-speaker or headphone cables are attached to the audio connector, the internal speaker, if present, is disabled. In most cases, if an audio adapter is installed in one of the expansion slots, the audio function built into the system board is disabled; use the audio jacks on the adapter. • Make sure that the program you are running is designed for use in the Microsoft Windows operating system.
An audio disc or AutoPlay-enabled disc does not automatically play when it is inserted into a CD drive Symptom: An audio disc or AutoPlay-enabled disc does not automatically play when it is inserted into a CD drive. Actions: • If you have multiple CD or DVD drives installed (or a combination of CD and DVD drives), try inserting the disc into the other drive. In some cases, only one of the drives is connected to the audio subsystem.
Actions: • Restart the DVD player program. • Close any open files, turn off the computer, and then restart the computer. • Try a lower screen resolution or color depth. If these actions do not correct the problem, run the Lenovo Solution Center program. If you need technical assistance, see Chapter 11 “Getting information, help, and service” on page 135. DVD movie will not play Symptom: DVD movie will not play. Actions: • Make sure that the disc surface is clean and not scratched.
• On computers that have a CD-ROM or CD-RW drive in addition to a DVD-ROM drive, make sure that the DVD disc is in the drive labeled “DVD”. If these actions do not correct the problem, run the Lenovo Solution Center program. If you need technical assistance, see Chapter 11 “Getting information, help, and service” on page 135. Intermittent problems Symptom: A problem occurs only occasionally and is difficult to repeat.
3. Click Devices and Printers. 4. Double-click USB Enhanced Performance Keyboard. The USB Enhanced Performance Keyboard Customization program starts. If these actions do not correct the problem, have the computer and keyboard serviced. See Chapter 11 “Getting information, help, and service” on page 135 for details. The mouse or pointing device does not work Symptom: The mouse or pointing device does not work.
Action: If the Transceiver Communications LED is not on, reconnect the transceiver and the keyboard. Monitor problems Note: Many monitors have status-indicator lights and built-in controls for adjusting brightness, contrast, width, height, and other picture adjustments. However, the controls vary from monitor type to monitor type. For information about the status lights and using the controls, refer to the documentation that comes with your monitor.
Actions: • The monitor might be operating in a low-refresh rate display mode. Set the monitor to the highest, noninterlaced refresh rate supported by your monitor and the video controller in your computer. Attention: Using a resolution or refresh rate that is not supported by your monitor might damage it. Check the documentation that comes with your monitor to verify the supported refresh rates. • The monitor might be affected by interference from nearby equipment.
Ethernet problems For Ethernet problems, select your symptom from the following list: • “Your computer cannot connect to the network” on page 127 • “The adapter stops working for no apparent reason” on page 127 • “If your computer is a Gigabit Ethernet model and you use a speed of 1000 Mbps, the connection fails or errors occur” on page 128 • “If your computer is a Gigabit Ethernet model, it cannot connect to the network at 1000 Mbps.
Action: The network driver files may be corrupt or missing. Update the driver by referring to the “Solution” description for the procedure to make sure that the correct device driver is installed. The Wake on LAN feature is not working Symptom: The Wake on LAN (WOL) feature is not working. Actions: • Make sure that WOL is enabled in the BIOS Setup Utility program. • If it is, check with your LAN administrator for the necessary settings.
Bluetooth problem Symptom: Sound does not come from the Bluetooth headset or headphone but comes from the local speaker even though the headset or headphone is connected using the Headset profile or AV profile. Action: Do the following: 1. Exit the application that uses the sound device (for example, Windows Media Player). 2. Open Control Panel. 3. Click Hardware and Sound ➙ Sound. 4. Select the Playback tab. 5.
– All external SCSI options are turned on. External SCSI options must be turned on before the computer is turned on. For more information, see your SCSI documentation. • Verify that the option and any required device drivers are installed correctly. If these actions do not correct the problem, run the Lenovo Solution Center program. If you need technical assistance, see Chapter 11 “Getting information, help, and service” on page 135.
4. Click Clean up system files. 5. Click the More Options tab. 6. In the Programs and Features area, click the Clean up button. 7. A list of installed programs is displayed. Select the program that you want to remove. Click Uninstall/Change. • Clean out your Inbox, Sent Items, and Deleted Items folders from your e-mail application. The folder names and procedures vary depending on your e-mail application. If you need assistance, see the help system for your e-mail application.
Actions: Verify that: 1. The printer is turned on and is online. 2. Paper is loaded correctly. 3. The printer signal cable is securely connected to the correct parallel, serial, or USB connector on the computer. Note: Non-IEEE-approved printer signal cables might cause unpredictable problems. 1. Any device drivers and other software that came with the printer are correctly installed. 2. You have assigned the printer port correctly in your operating system, application program, or BIOS settings.
Actions: • Most software programs have built-in help systems that provide instructions for most tasks. If you are having difficulty performing a specific task within a software program, refer to the help system for that program. Help systems are typically accessible from a menu or button in the program, and frequently from the F1 key. • If you are having difficulty with the Windows operating system or one of its components, refer to the Windows help system. It is accessible from the Windows Start menu.
Lenovo Solution Center The Lenovo Solution Center program enables you to troubleshoot and resolve computer problems. It combines diagnostic tests, system information collection, security status, and support information, along with hints and tips for maximum system performance. Notes: • The Lenovo Solution Center program can be downloaded from http://www.lenovo.com/diags. • If you are using other Windows operating system rather than Windows 7 and Windows 8, go to http://www.lenovo.
Chapter 11. Getting information, help, and service This chapter contains information about help, service, and technical assistance for products manufactured by Lenovo. Information resources You can use the information in this section to access useful resources relating to your computing needs. Lenovo ThinkVantage Tools The Lenovo ThinkVantage Tools program guides you to a host of information sources and provides easy access to various tools to help you work more easily and securely.
• Access troubleshooting and support information for your computer model and other supported products. • Find the service and support phone numbers for your country or region. • Find a Service Provider located near you. Lenovo Support Web site Technical support information is available on the Lenovo Support Web site at: http://www.lenovo.
• • • • • • Replacement or use of parts not manufactured for or by Lenovo or non-warranted Lenovo parts Identification of software problem sources Configuration of BIOS as part of an installation or upgrade Changes, modifications, or upgrades to device drivers Installation and maintenance of network operating systems (NOS) Installation and maintenance of application programs Refer to the Safety, Warranty, and Setup Guide that comes with your computer for information about your warranty type and duration.
138 ThinkCentre M83, M93/p User Guide
Appendix A. Notices Lenovo may not offer the products, services, or features discussed in this document in all countries. Consult your local Lenovo representative for information on the products and services currently available in your area. Any reference to a Lenovo product, program, or service is not intended to state or imply that only that Lenovo product, program, or service may be used.
Trademarks The following terms are trademarks of Lenovo in the United States, other countries, or both: Lenovo Rescue and Recovery ThinkCentre ThinkVantage The Lenovo logo Microsoft and Windows are trademarks of the Microsoft group of companies. Intel, Intel Core, Celeron, and Pentium are trademarks of Intel Corporation in the U.S. and/or other countries. Linux is a registered trademark of Linus Torvalds. Other company, product, or service names may be trademarks or service marks of others.
Appendix B. Regulatory information Export classification notice This product is subject to the United States Export Administration Regulations (EAR) and has an Export Classification Control Number (ECCN) of 4A994.b. It can be re-exported except to any of the embargoed countries in the EAR E1 country list. Electronic emissions notices The following information refers to Lenovo personal computer machine types 10A0, 10A1, 10A6, 10A7, 10AG, 10AK, and 10AL.
European Union - Compliance to the Electromagnetic Compatibility Directive This product is in conformity with the protection requirements of EU Council Directive 2004/108/EC on the approximation of the laws of the Member States relating to electromagnetic compatibility. Lenovo cannot accept responsibility for any failure to satisfy the protection requirements resulting from a non-recommended modification of the product, including the installation of option cards from other manufacturers.
Korea Class B compliance statement Japan VCCI Class B compliance statement Japan compliance statement for products which connect to the power mains with rated current less than or equal to 20 A per phase Lenovo product service information for Taiwan Keyboard and mouse compliance statement for Taiwan Eurasian compliance mark Additional regulatory information For additional regulatory information, refer to the Regulatory Notice shipped with your computer.
144 ThinkCentre M83, M93/p User Guide
Appendix C. WEEE and recycling information Lenovo encourages owners of information technology (IT) equipment to responsibly recycle their equipment when it is no longer needed. Lenovo offers a variety of programs and services to assist equipment owners in recycling their IT products. For information on recycling Lenovo products, go to: http://www.lenovo.
Some Lenovo computer products sold in Japan may have components that contain heavy metals or other environmental sensitive substances. To properly dispose of disused components, such as a printed circuit board or drive, use the methods described above for collecting and recycling a disused computer or monitor.
Batteries or packaging for batteries are labeled in accordance with European Directive 2006/66/EC concerning batteries and accumulators and waste batteries and accumulators. The Directive determines the framework for the return and recycling of used batteries and accumulators as applicable throughout the European Union. This label is applied to various batteries to indicate that the battery is not to be thrown away, but rather reclaimed upon end of life per this Directive.
148 ThinkCentre M83, M93/p User Guide
Appendix D. Restriction of Hazardous Substances Directive (RoHS) European Union RoHS Lenovo products sold in the European Union, on or after 3 January 2013 meet the requirements of Directive 2011/65/EU on the restriction of the use of certain hazardous substances in electrical and electronic equipment (“RoHS recast” or “RoHS 2”). For more information about Lenovo progress on RoHS, go to: http://www.lenovo.com/social_responsibility/us/en/RoHS_Communication.
Ukraine RoHS India RoHS RoHS compliant as per E-Waste (Management & Handling) Rules, 2011.
Appendix E.
152 ThinkCentre M83, M93/p User Guide
Appendix F. ENERGY STAR model information ENERGY STAR® is a joint program of the U.S. Environmental Protection Agency and the U.S. Department of Energy aimed at saving money and protecting the environment through energy efficient products and practices. Lenovo is proud to offer our customers products with an ENERGY STAR compliant designation.
154 ThinkCentre M83, M93/p User Guide
Index A a rescue medium, creating and using Administrator, password 106 audio line-in connector 12 audio line-out connector 12 audio subsystem 1 B backup and recovery operations basic troubleshooting 117 battery, replacing 53 boot-block recovery 112 98 C cable lock, security 31–32 card reader, installing 45 card reader, replacing 48 changing password 106 startup device sequence 108 cleaning an optical mouse 115 CMOS, clearing 107 components, internal 14 computer cover removing 36 computer cover, reinstal
warranty 135 Input/Output (I/O) features installing mSATA solid-state drive solid-state drive 70 installing options memory module 41 PCI card 38 internal drives 1 internal speaker, replacing lost or forgotten 107 passwords, using 105 PCI card 38 installing, replacing 38 slots 38 physical specifications 5 power features 3 power supply assembly, replacing 55 power-on self-test (POST) 111 Power-On, Password 106 programs, updating system 111 purchasing additional services 137 3 60 78 K Kensington-style cabl
setting password 106 settings changing 105 viewing 105 Setup Utility 105 Setup Utility program, starting 105 Setup Utility, exiting 110 software recovering 97 solid-state drive, installing 70 solving recovery problems 102 starting the Setup Utility program 105 startup device 108 sequence, changing 108 temporary, selecting 108 static-sensitive devices, handling 35 system management 2 programs 111 system board connectors 15–16 locating parts 14 locations 14 memory module 41 Wi-Fi units, Wi-Fi adapter card, W
158 ThinkCentre M83, M93/p User Guide