ThinkStation P300 User Guide Machine Types: 10DA, 30AG, and 30AH
Note: Before using this information and the product it supports, be sure to read and understand the “Read this first: Important safety information” on page v and Appendix E “Notices” on page 15. Fourth Edition (April 2015) © Copyright Lenovo 2014, 2015. LIMITED AND RESTRICTED RIGHTS NOTICE: If data or software is delivered pursuant a General Services Administration “GSA” contract, use, reproduction, or disclosure is subject to restrictions set forth in Contract No. GS-35F-05925.
Contents Read this first: Important safety information . . . . . . . . . . . . . . . v Service and upgrades . . . . . . . . . . Static electricity prevention . . . . . . . . Power cords and power adapters . . . . . Extension cords and related devices . . . . Polyvinyl Chloride (PVC) cable and cord notice Plugs and outlets. . . . . . . . . . . . External devices . . . . . . . . . . . . Heat and product ventilation . . . . . . . Operating environment . . . . . . . . . Laser compliance statement . . . . . . .
Creating RAID volumes . . . . . . . . . Deleting RAID volumes . . . . . . . . . Resetting disks to non-RAID . . . . . . . 45 45 46 Chapter 6. Preventing problems . . . 47 Keeping your computer current . . . . . . Getting the latest device drivers for your computer . . . . . . . . . . . . . Updating your operating system . . . . Using System Update . . . . . . . . Cleaning and maintenance . . . . . . . . Basics . . . . . . . . . . . . . . Cleaning your computer . . . . . . . Good maintenance practices .
Export classification notice . . . . . . . Electronic emissions notices . . . . . . Federal Communications Commission Declaration of Conformity . . . . . Eurasian compliance mark . . . . . . . Brazil regulatory notice . . . . . . . . Mexico regulatory notice . . . . . . . . Additional regulatory information . . . . . . . . . . . . 3 3 . . . . . 3 5 5 5 5 . . . . . . . . . . . . . . . Appendix B. WEEE and recycling information . . . . . . . . . . . . . . . 7 Important WEEE information . . . . . . .
iv ThinkStation P300 User Guide
Read this first: Important safety information CAUTION: Before using this manual, be sure to read and understand all the related safety information for this product. Refer to the information in this section and the safety information in the Safety, Warranty, and Setup Guide that you received with this product. Reading and understanding this safety information reduces the risk of personal injury and damage to your product.
or CRU, do not open the static-protective package containing the part until the instructions direct you to install it. When you handle options or CRUs, or perform any work inside the computer, take the following precautions to avoid static-electricity damage: • Limit your movement. Movement can cause static electricity to build up around you. • Always handle components carefully. Handle adapters, memory modules, and other circuit boards by the edges. Never touch exposed circuitry.
Polyvinyl Chloride (PVC) cable and cord notice Many personal computer products and accessories contain cords, cables or wires, such as power cords or cords to connect the accessory to a personal computer.
• Ventilation slots, fans, and heat sinks are provided with the product for safety, comfort, and reliable operation. These features might inadvertently become blocked by placing the product on a bed, sofa, carpet, or other flexible surface. Never block, cover, or disable these features. Inspect your desktop computer for dust accumulation at least once every three months.
• Do not remove the covers. Removing the covers of the laser product could result in exposure to hazardous laser radiation. There are no serviceable parts inside the device. • Use of controls or adjustments or performance of procedures other than those specified herein might result in hazardous radiation exposure. DANGER Some laser products contain an embedded Class 3A or Class 3B laser diode. Note the following: Laser radiation when open.
x ThinkStation P300 User Guide
Chapter 1. Product overview This chapter provides the following information: • Locations of connectors • Locations of components • Locations of parts on the system board • Locations of internal drives • Computer features • Software programs provided by Lenovo Locations This section provides the following topics: • “Locating connectors, controls, and indicators on the front of your computer” on page 2 • “Locating connectors on the rear of your computer” on page 3 • “Locating components” on page 5.
Locating connectors, controls, and indicators on the front of your computer The following illustration shows the locations of the connectors, controls, and indicators on the front of your computer. Figure 1. Front connector, control, and indicator locations 2 1 Optical drive eject/close button 2 USB 3.
Locating connectors on the rear of your computer The following illustration shows the locations of the connectors on the rear of your computer. Some connectors on the rear of your computer are color-coded to help you determine where to connect the cables on your computer. Figure 2. Rear connector locations 1 Power-cord connector 2 Serial connector 3 VGA connector 4 DisplayPort® connectors 5 USB 3.0 connectors (4) 6 USB 2.
Connector Description Audio line-in connector Used to receive audio signals from an external audio device, such as a stereo system. When you attach an external audio device, a cable is connected between the audio line-out connector of the device and the audio line-in connector of the computer.
Locating components The following illustration shows the locations of the various components in your computer. To remove the computer cover, see “Removing the computer cover” on page 71. Figure 3.
Locating parts on the system board The following illustration shows the locations of the parts on the system board. Figure 4.
Locating internal drives Internal drives are devices that your computer uses to read and store data. You can add drives to your computer to increase storage capacity and enable your computer to read other types of media. Internal drives are installed in bays. When installing or replacing an internal drive, it is important to note the type and size of the drive that you can install or replace in each bay and correctly connect the cables to the drive installed.
Machine type and model label The machine type and model label identifies your computer. When you contact Lenovo for help, the machine type and model information helps support technicians to identify your computer and provide faster service. The following is a sample of the machine type and model label. Figure 6. Machine type and model label Features This section introduces the computer features. The information covers a variety of models.
• On the Microsoft Windows 8.1 operating system, go to the desktop and move your pointer to the top-right or bottom-right corner of the screen to display the charms. Then click Settings ➙ PC info to view the information. For more information, see “Installing or replacing a memory module” on page 76.
For more information, see “Locating connectors, controls, and indicators on the front of your computer” on page 2 and “Locating connectors on the rear of your computer” on page 3.
• Intelligent Cooling Engine (ICE) The Intelligent Cooling Engine is a system thermal management solution that enables your computer to run with better thermal and acoustic performance. The ICE function also monitors the thermal performance of your computer to identify thermal problems. For more information, see “ICE performance mode” on page 41 and “ICE thermal alert” on page 41.
Preinstalled operating system Your computer is preinstalled with one of the following operating systems: • Microsoft Windows 7 operating system • Microsoft Windows 8.1 operating system Operating system(s), certified or tested for compatibility (varies by model type) The operating system(s) listed here are being certified or tested for compatibility at the time this publication goes to press.
program name. You can find the program by its program name or icon name as shown in the Lenovo programs available on the Windows 7 operating system table. Note: If you do not find the program you need, open the Lenovo ThinkVantage® Tools program to find the dimmed icon for the program. Then double-click the icon to install the program. To access Lenovo programs through Windows Search, do the following: 1. Click the Start button and then type the program name or the icon name into the search box. 2.
• Create Recovery Media • Fingerprint Manager Pro or ThinkVantage Fingerprint Software • Lenovo Performance Tuner • Lenovo Reach • Lenovo SHAREit • Lenovo Solution Center • Lenovo Tools • System Update An introduction to Lenovo programs This topic provides a brief introduction to some Lenovo programs. Note: Depending on your computer model, some of the Lenovo programs might not be available. • Companion Your system’s best features should be easy to access and understand. With Companion, they are.
The Lenovo Solution Center program enables you to troubleshoot and resolve computer problems. It combines diagnostic tests, system information collection, security status, and support information, along with hints and tips for maximum system performance. • Lenovo ThinkVantage Tools The Lenovo ThinkVantage Tools program provides easy access to various tools to help you work more easily and securely.
16 ThinkStation P300 User Guide
Chapter 2. Using your computer This chapter provides information about the following topics: • “Registering your computer” on page 17 • “Using keyboard shortcuts” on page 17 • “Using the wheel mouse” on page 18 • “Setting the computer volume” on page 18 • “Using a disc” on page 19 • “Navigating among screens on the Windows 8.1 operating system” on page 21 • “Accessing Control Panel on the Windows 8.
Using the wheel mouse The wheel mouse has the following controls: 1 Primary mouse button: Use this button to select or start a program or menu item. 2 Wheel: Use the wheel to control the scrolling action of the mouse. The direction in which you rotate the wheel controls the direction of the scrolling action. 3 Secondary mouse button: Use this button to display a menu for the active program, icon, or object. You can view and change the settings of your mouse by doing the following: 1.
3. Click Turn system icons on or off and change the volume behaviors from Off to On. 4. Click OK to save the new settings. • For Windows 8.1: 1. Open Control Panel, and click Appearance and Personalization. Note: For detailed information on how to open Control Panel on Windows 8.1, see “Accessing Control Panel on the Windows 8.1 operating system” on page 22. 2. In the Taskbar and Navigation section, click Customize icons on the taskbar. 3.
• Do not insert any object other than a disc into the drive. • Do not insert damaged discs into the drive. Warped, scratched, or dirty discs can damage the drive. • Before moving the computer, remove the disc from the drive. Handling and storing a disc When handling and storing a disc, follow these guidelines: • Hold the disc by its edges. Do not touch the surface of the side that is not labeled. • To remove dust or fingerprints, wipe the disc with a clean, soft cloth from the center to the outside.
1. On the Start screen, click the down arrow in the bottom-left corner to go to the Apps screen. Then type Power2Go in the search box in the top-right corner of the screen. 2. Click Power2Go in the search result to open the program. 3. Follow the instructions on the screen. Navigating among screens on the Windows 8.1 operating system To navigate among the desktop, the Start screen, and applications that were opened from the Start screen on the Windows 8.
Note: Only active workspaces that you have accessed during the current Windows session are displayed along the left edge. If you close an active workspace, its representation will not be displayed along the left edge of the screen. 2. Click the representation. – Using a touch screen: • Method 1 1. Swipe in and out on the left edge of the screen. Representations of all available workspaces are displayed along the left edge of the screen. 2. Tap the desired workspace. • Method 2 1.
How can I restore my computer settings? Your computer provides a program that enables you to restore the computer settings. For more information, see Chapter 8 “Recovery information” on page 63. Additionally, in case of a hard-disk-drive failure, you can order a recovery disc set from the Lenovo Customer Support Center. For information about contacting the Customer Support Center, see Chapter 10 “Getting information, help, and service” on page 127.
24 ThinkStation P300 User Guide
Chapter 3. You and your computer This chapter provides information about accessibility, comfort, and relocating your computer to other countries or regions. Accessibility and comfort Good ergonomic practice is important to get the most from your personal computer and to avoid discomfort. Arrange your workplace and the equipment you use to suit your individual needs and the kind of work that you perform. In addition, use healthy work habits to maximize your performance and comfort while using your computer.
Glare and lighting Position the monitor to minimize glare and reflections from overhead lights, windows, and other light sources. Reflected light from shiny surfaces can cause annoying reflections on your monitor screen. Place the monitor at right angles to windows and other light sources, when possible. Reduce overhead lighting, if necessary, by turning off lights or using lower wattage bulbs. If you install the monitor near a window, use curtains or blinds to block the sunlight.
select one object with your keyboard, the object is highlighted. When you move the pointer to one object with your mouse, the introductory text of the object is displayed. To use on-screen notification, open Control Panel, click Ease of Access ➙ Ease of Access Center, and then click Use text or visual alternatives for sounds. Audio notification Audio notification helps visually impaired people or people with weak sight be aware of the status of their computer.
For more information about how to use and configure Speech Recognition, see the Windows Help and Support information system. Customizable text size Depending on your preference, you can change only the text size instead of changing the size of everything on the desktop. To change the text size, open Control Panel and click Appearances and Personalization ➙ Display. Then, go to Change only the text size and set a text size that meets your needs.
Ease of Access keyboard shortcuts The following table contains keyboard shortcuts that can help make your computer easier to use.
Documentation in accessible formats Lenovo provides electronic documentation in accessible formats. Lenovo electronic documentation, such as properly tagged PDF files or HyperText Markup Language (HTML) files, is developed to ensure that visually impaired users can read the documentation through a screen reader. Each image in the documentation also includes adequate alternative text to explain the image so that visually impaired users can understand the image when they use a screen reader.
Chapter 4. Security This chapter provides information about how to protect your computer from theft and unauthorized use. Locking the computer cover Locking the computer cover helps prevent unauthorized people from gaining access to the inside of your computer. Your computer comes with a padlock loop so that the computer cover cannot be removed when a padlock is installed. Figure 7.
Attaching a Kensington-style cable lock You can use a Kensington-style cable lock to secure your computer to a desk, table, or other non-permanent fixture. The cable lock attaches to the security-lock slot at the rear of your computer and is operated with a key or combination depending on the type selected. The cable lock also locks the buttons used to open the computer cover. This is the same type of lock used with many notebook computers.
Attaching a cable lock A cable lock can be used to secure devices, such as the keyboard and the mouse, by locking the device cables to your computer. The cable lock attaches to the cable-lock slots on the rear of your computer. See “Locating connectors on the rear of your computer” on page 3. To install a cable lock, do the following: 1. Insert the clip 1 into the cable-lock slot 4 . 2. Pull the cables you want to lock through the dents in the cable lock. 3.
• Administrator password: Setting an administrator password deters unauthorized users from changing configuration settings. If you are responsible for maintaining the configuration settings of several computers, you might want to set an administrator password. For more information about BIOS passwords, see “Using BIOS passwords” on page 38.You do not have to set any passwords to use your computer. However, using passwords improves computing security.
3. Select Preboot Authentication or Erase Fingerprint Data as desired, and press Enter. Note: • Preboot Authentication: enables or disables the fingerprint authentication for accessing the BIOS. • Erase Fingerprint Data: clears the fingerprint data stored in a fingerprint reader. 4. Select the desired settings and press Enter. 5. Press F10 to save changes and exit the Setup Utility program. Press Enter when prompted to confirm the exit.
36 ThinkStation P300 User Guide
Chapter 5. Advanced configuration This chapter provides the following information to help you configure the computer: • “Using the Setup Utility program” on page 37 • “Updating or recovering the BIOS” on page 42 • “Configuring RAID” on page 44 Using the Setup Utility program The Setup Utility program is used to view and change the configuration settings of your computer, regardless of which operating system you are using.
You can use either the keyboard or the mouse to navigate through menu choices. The keys used to perform various tasks are displayed at the bottom of each screen. Using BIOS passwords By using the Setup Utility program, you can set passwords to prevent unauthorized access to your computer and data. You do not have to set any passwords to use your computer. However, using passwords improves computer security. If you decide to set any passwords, read the following topics.
Setting, changing, and deleting a password To set, change, or delete a password, do the following: 1. Start the Setup Utility program. See “Starting the Setup Utility program” on page 37. 2. From the Setup Utility program main menu, select Security. 3. Depending on the password type, select Set Power-On Password, Set Administrator Password, or Hard Disk Password. 4. Follow the instructions on the right side of the screen to set, change, or delete a password.
5. Press F10 to save changes and exit the Setup Utility program. See “Exiting the Setup Utility program” on page 42. Selecting a startup device If your computer does not start up from a device such as the disc or hard disk drive as expected, do one of the following to select the startup device you want. Selecting a temporary startup device Use this procedure to select a temporary startup device. Note: Not all discs and hard disk drives are bootable. 1. Turn on or restart your computer. 2.
• Press the power button • Enable the wake up on alarm feature The wake up on alarm feature enables your computer to wake up at a set time. To enable the wake up on alarm feature, do the following: 1. Start the Setup Utility program. 2. From the Setup Utility program main menu, select Power ➙ Automatic Power On, and press Enter. 3. Select Wake Up on Alarm and press Enter. Then follow the instructions on the screen. 4. Press F10 to save changes and exit the Setup Utility program.
After enabling the ICE thermal alert function, when critical thermal situations occur, such as malfunctioning fans, abnormally high temperature, and poor cooling performances, an alert log will be written into the Windows system log. The alert log can help you identify the thermal problems. To configure the ICE thermal alert function, do the following: 1. Start the Setup Utility program. See “Starting the Setup Utility program” on page 37. 2. From the Setup Utility program main menu, select Power. 3.
models, you can download either an update program to create a system-program-update disc or an update program that can be run from the operating system. Updating the BIOS from a disc This section provides instructions on how to update the BIOS from a disc. Note: You can download a self-starting bootable disc image (known as an ISO image) with the system program updates to create a system-program-update disc. Go to: http://www.lenovo.com/support To update the BIOS from a disc on the Windows 8.
6. Follow the instructions on the screen to complete the update. After the update is completed, remove the disc from the optical drive. Updating the BIOS from your operating system Lenovo makes constant improvements to its Web sites. The Web page contents are subject to change without notice, including the contents referenced in the following procedure. To update the BIOS from your operating system, do the following: 1. Go to http://www.lenovo.
• RAID Level 0 – Striped disk array – Two hard disk drives minimum – Better performance without fault tolerance • RAID Level 1 – Mirrored disk array – Two hard disk drives minimum – Improved read performance and 100% redundancy To install a secondary hard disk drive, refer to “Replacing the secondary hard disk drive” on page 109. Configuring the system BIOS to enable SATA RAID functionality This section describes how to configure the system BIOS to enable SATA RAID functionality.
3. Use the arrow keys to select the RAID volume to be deleted and press Delete. 4. When prompted, press Y to confirm the deletion of the selected RAID volume. Deleting a RAID volume will reset the hard disk drives to non-RAID. 5. After deleting a RAID volume, you can: • Return to step 2 to delete additional RAID volumes. • See “Creating RAID volumes” on page 45 for RAID volume creation. • Use the up and down arrow keys to select Exit and press Enter.
Chapter 6. Preventing problems This chapter provides information that can help you avoid common problems and keep your computer running smoothly. Keeping your computer current In some situations you might find it necessary to have the most current software programs, device drivers, or operating system. This section explains how to get the latest updates for your computer. Getting the latest device drivers for your computer Note: Lenovo makes constant improvements to its Web sites.
Using System Update The System Update program (hereinafter referred to as System Update) provides regular access to system and software updates for your computer to keep your system and software up-to-date. System Update gathers information from the Lenovo Help Center about new updates for your computer, and then sorts and displays each update as critical, recommended, or optional to help you understand the importance. You have complete control of which updates to download and install.
2. Wipe each keytop surface with the cloth. Wipe the keys one by one; if you wipe several keys at a time, the cloth may hook onto an adjacent key and possibly damage it. Ensure that no liquid drips onto or between the keys. 3. To remove any crumbs or dust from beneath the keys, you can use a camera blower with a brush or cool air from a hair dryer. Note: Avoid spraying cleaner directly onto the keyboard.
• Make backup copies of critical data on removable media memory, such as discs and USB storage devices, at regular intervals and store the removable media in a safe location. The frequency of making backup copies depends on how critical the data is to you or your business. • Back up your entire hard disk drive on a regular basis. • Keep your computer software, device drivers, and operating system up-to-date. See “Keeping your computer current ” on page 47 for more information. • Keep a log book.
Chapter 7. Troubleshooting and diagnostics This chapter provides information about diagnosing and troubleshooting computer problems. If your computer problem is not described here, see Chapter 10 “Getting information, help, and service” on page 127 for additional troubleshooting resources. Basic troubleshooting The following table provides some basic instructions to help you troubleshoot your computer problems. Note: If you cannot correct the problem, have the computer serviced.
Symptom Action The operating system does not start. Ensure that the startup sequence includes the device where the operating system resides. Usually, the operating system is on the hard disk drive. For more information, see “Selecting a startup device” on page 40. The computer beeps multiple times before the operating system starts. Ensure that no keys are stuck.
1. Remove the new hardware option or software. If you must remove the computer cover to remove a hardware option, ensure that you review and follow the electrical safety information provided with your computer. For your safety, do not operate the computer with the cover removed. 2. Run the diagnostic program to ensure your computer is operating correctly. 3. Reinstall the new hardware option or software following the instructions provided by the manufacturer.
A CD or DVD does not work Solutions: • Ensure that the disc is inserted correctly, with its label up. • Ensure that the disc you are using is clean. To remove dust or fingerprints, wipe the disc clean with a soft cloth from the center to the outside. Wiping a disc in a circular motion might cause loss of data. • Ensure that the disc you are using is not scratched or damaged. Try inserting another disc that you know is good.
• Ensure that a DVD disc is in the drive with the shiny side of the disc facing down. • Ensure that video resolution is set to less than 1152 x 864 pixels. • On computers that have a CD-ROM or CD-RW drive in addition to a DVD-ROM drive, ensure that the DVD disc is in the drive labeled “DVD”. Intermittent problems Some problems occur only occasionally and are difficult to repeat. Solutions: • Ensure that all cables and cords are securely connected to the computer and attached devices.
• If you are using a USB mouse, enable the USB connectors in the BIOS settings. For more information, see “Enabling or disabling a device” on page 39. The pointer on the screen does not move smoothly with the mouse Solution: Clean the mouse. For more information, see “Optical mouse” on page 49. The fingerprint reader on the keyboard does not work Solutions: • Enroll your fingerprint correctly. • Never scratch the surface of the reader with a hard, pointed object.
Note: To open Control Panel on Windows 8.1, see “Accessing Control Panel on the Windows 8.1 operating system” on page 22 2. Click Hardware and Sound ➙ Adjust screen resolution ➙ Advanced settings. 3. Click the Monitor tab to reset the refresh rate. Set the refresh rate to be the highest, noninterlaced refresh rate supported on your computer. Refer to the documentation that comes with your monitor for the supported refresh rates.
• Install all networking software that is necessary for your network environment. Check with your LAN administrator for the necessary networking software. The adapter stops working for no reason Solution: The network driver files might be corrupt or missing. Update the driver by referring to the “Solution” description for the previous problem to ensure that the latest device driver is installed. The Wake On LAN feature is not working Solution: Enable the Wake On LAN (WOL) feature in the BIOS program.
4. Select the Playback tab. 5. If you are using the Headset profile, select Bluetooth Hands-free Audio, and then click Set Default. If you are using the AV profile, select Stereo Audio, and then click Set Default. 6. Click OK. Note: Bluetooth is supported only on some computer models. I have connected an option to my computer, but it does not work Solution: Refer to the documentation that comes with the option to ensure that you have connected the option correctly.
2. Click Start ➙ Computer. 3. Right-click your C drive entry and then click Properties. 4. Click Defragment now under the Tools tab to start a disk-defragmentation process. • On Windows 8.1: 1. Close any open programs and windows. 2. Open File Explorer. 3. Right-click your C drive entry and then click Properties. 4. Click Optimize under the Tools tab to start a disk-defragmentation process. Insufficient memory Solution: Install additional memory modules.
When using a sort feature, dates cannot be sorted in the correct order Solution: Some application programs developed before the year 2000 used only the last two digits of a year to sort dates, assuming the first two digits were 19. Consequently, dates cannot be sorted in the correct order. Check with your software manufacturer to see if any updates are available. Many software manufacturers make updates available from the World Wide Web.
62 ThinkStation P300 User Guide
Chapter 8. Recovery information This chapter provides information about the recovery solutions. There are a variety of methods to choose from when considering how to recover from a software- or hardware-related problem. Some methods vary depending on the type of operating system that is installed. You can restore the computer settings using a program or the recovery disc set. For more information about using the recovery disc set, see the documentation that comes with the disc set.
Creating recovery media Note: On the Windows 7 operating system, you can create recovery media using discs or external USB storage devices. To create recovery media on the Windows 7 operating system, click Start ➙ All Programs ➙ Lenovo ThinkVantage Tools ➙ Factory Recovery Disks. Then, follow the instructions on the screen.
• “Performing a recovery operation from the Rescue and Recovery workspace” on page 65 Performing a recovery operation from Windows 7 To perform a recovery operation using the Rescue and Recovery program on the Windows 7 operating system, do the following: 1. From the Windows desktop, click Start ➙ All Programs ➙ Lenovo ThinkVantage Tools ➙ Enhanced Backup and Restore. The Rescue and Recovery program opens. 2. In the Rescue and Recovery main window, click the Launch advanced Rescue and Recovery arrow. 3.
For more information about the features of the Rescue and Recovery workspace, click Help. Creating and using a rescue medium With a rescue medium, such as a disc or a USB hard disk drive, you can recover the computer from failures that prevent you from gaining access to the Rescue and Recovery workspace on your hard disk drive. Notes: • The recovery operations you can perform using a rescue medium vary depending on the operating system. • The rescue disc can be started in all types of optical drives.
Reinstalling preinstalled programs and device drivers Your computer enables you to reinstall preinstalled programs and device drivers. Reinstalling preinstalled programs To reinstall programs preinstalled on your Lenovo computer, do the following: 1. Turn on the computer. 2. Go to C:\SWTOOLS. 3. Open the apps folder and locate the subfolder that is named after the program preinstalled on your computer. 4. Open the subfolder and locate the EXE file. 5.
Note: Reinstall device drivers will change the current configuration of your computer. Reinstall device drivers only when it is necessary to correct a problem with your computer. Solving recovery problems Note: Ensure that your rescue device is set as the first boot device in the startup device sequence in the Setup Utility program. See “Selecting a startup device” on page 40 for detailed information about temporarily or permanently changing the startup device sequence.
2. In the Remove everything and reinstall Windows section, click Get started. Using the advanced startup options Advanced startup options enable you to change the startup settings of your Windows operating system, start the computer from an external device, or restore the Windows operating system from a system image. To use the advanced startup options, do the following: 1. Move the pointer to the top-right or bottom-right corner of the screen to display the charms.
70 ThinkStation P300 User Guide
Chapter 9. Installing or replacing hardware This chapter provides instructions on how to install or replace hardware for your computer. Handling static-sensitive devices Do not open the static-protective package containing the new part until the defective part has been removed from the computer and you are ready to install the new part. Static electricity, although harmless to you, can seriously damage computer components and parts.
CAUTION: Before you open the computer cover, turn off the computer and wait several minutes until the computer is cool. To remove the computer cover, do the following: 1. Remove all media from the drives and turn off all attached devices and the computer. Then, disconnect all power cords from electrical outlets and disconnect all cables that are connected to the computer.
3. Remove the front bezel by releasing the three plastic tabs on the left side and pivoting the front bezel outward. Figure 11. Removing the front bezel 4. To reinstall the front bezel, align the three plastic tabs on the right side of the front bezel with the corresponding holes in the chassis, then pivot the front bezel inwards until it snaps into position on the left side. What to do next: • To work with another piece of hardware, go to the appropriate section.
3. At the rear of the computer, press the release button 1 to open the card latch 2 . Figure 12.
4. Depending on whether you are installing or replacing a PCI card, do one of the following: • If you are installing a PCI card, remove the appropriate metal slot cover. • If you are replacing an old PCI card, grasp the old card that is currently installed and gently pull it out of the slot. Figure 13. Removing a PCI card Notes: a. The card fits tightly into the card slot. If necessary, alternately move each side of the card a small amount until it is removed from the card slot. b.
7. Pivot the card latch to the closed position to secure the PCI card. Figure 15. Installing a PCI card What to do next: • To work with another piece of hardware, go to the appropriate section. • To complete the installation or replacement, go to “Completing the parts replacement” on page 125. Installing or replacing a memory module Attention: Do not open your computer or attempt any repair before reading and understanding the “Read this first: Important safety information” on page v.
5. Remove any parts that might prevent your access to the memory slots. Depending on your computer model, you might need to remove the PCI Express x16 graphics card for easier access to the memory slots. See “Installing or replacing a PCI card” on page 73. 6. Depending on whether you are installing or replacing a memory module, do one of the following: • If you are replacing an old memory module, open the retaining clips and gently pull the memory module out of the memory slot. Figure 16.
7. Position the new memory module over the memory slot. Ensure that the notch 1 on the memory module aligns correctly with the slot key 2 on the system board. Push the memory module straight down into the slot until the retaining clips close. Figure 18. Installing a memory module 8. Reinstall the PCI Express x16 graphics card if you have removed it. What to do next: • To work with another piece of hardware, go to the appropriate section.
1. Remove all media from the drives and turn off all attached devices and the computer. Then, disconnect all power cords from electrical outlets and disconnect all cables that are connected to the computer. 2. Remove the computer cover. See “Removing the computer cover” on page 71. 3. Remove the front bezel. See “Removing and reinstalling the front bezel” on page 72. 4. If you are installing an optical drive, do the following: a. Remove the metal static shield from the desired drive bay. b.
5. Install the optical drive retainer onto the left side of the new optical drive. Figure 21. Installing the optical drive retainer 6. Slide the new optical drive into the drive bay from the front of the computer until the optical drive snaps into position. Figure 22. Installing the optical drive 7. Connect the cables to the rear of the new optical drive. Figure 23. Connecting the cables to the rear of the new optical drive 8.
• To complete the installation or replacement, go to “Completing the parts replacement” on page 125. Installing or replacing a device in the 5.25-inch flex module Attention: Do not open your computer or attempt any repair before reading and understanding the “Read this first: Important safety information” on page v. This section provides instructions on how to install or replace a device in the 5.25-inch flex module. Installing and replacing a device in the 5.
a. press the button as shown to remove the slim optical drive from the flex module. Figure 26. Removing the slim optical drive from the flex module b. Remove the two screws that secure the clip to remove the plastic clip from the rear of the slim optical drive. Figure 27. Removing the plastic clip from the slim optical drive 4. Install the two screws to secure the plastic clip on the rear of the new slim optical drive. Figure 28.
5. Slide the new slim optical drive with the plastic clip into the flex module until the slim optical drive snaps into position. Figure 29. Installing the slim optical drive in the flex module 6. Position the flex module cover on the flex module so that the rail guides on the bottom of the flex module cover engage the rails on the flex module. Then, push the cover to the front of the flex module until it snaps into position. Figure 30.
2. Lift the clip on the side of the flex module upward and slide the flex module cover to the rear of the flex module to remove the cover. Figure 31. Removing the flex module cover 3. If you are replacing a card reader, do the following: a. Disconnect the card reader cable from the system board. See “Locating parts on the system board” on page 6. b. Pull the clip as shown to remove the card reader with the card reader retaining bracket out of the flex module. Figure 32.
4. To install the a new card reader into the card reader retaining bracket, align the four holes in the card reader with the corresponding studs on the bracket and then press the new card reader downward until it snaps into position. Figure 34. Installing the card reader into the card reader retaining bracket 5. Note the orientation of the new card reader and route the card reader cable into the cable clip.
6. Position the flex module cover on the flex module so that the rail guides on the bottom of the flex module cover engage the rails on the flex module. Then, push the cover to the front of the flex module until it snaps into position. Figure 36. Reinstalling the flex module cover 7. Connect the card reader cable to the USB 2.0 connector or card reader connector on the system board. See “Locating parts on the system board” on page 6.
a. Disconnect the eSATA connector or IEEE 1394 connector cable from the system board. See “Locating parts on the system board” on page 6. b. Press the two clips toward each other as shown to pull the eSATA connector or IEEE 1394 connector out of the flex module. Figure 38. Removing the eSATA connector or IEEE 1394 connector in the flex module 4. Note the orientation of the eSATA connector or IEEE 1394 connector and route the eSATA connector or IEEE 1394 connector cable into the cable clip. 5.
6. Position the flex module cover on the flex module so that the rail guides on the bottom of the flex module cover engage the rails on the flex module. Then, push the cover to the front of the flex module until it snaps into position. Figure 40. Reinstalling the flex module cover 7. Connect the eSATA connector or IEEE 1394 connector cable to the corresponding connector on the system board. See “Locating parts on the system board” on page 6.
a. press the release button 1 to eject the tab 2 that secures the slim optical drive. Then, slide the slim optical drive out of the front of the 5.25-inch cage assembly. Figure 41. Removing the slim optical drive in the 5.25-inch cage assembly b. Remove the two screws that secure the slim optical drive retainer. Figure 42. Removing the slim optical drive retainer Chapter 9.
3. Install the two screws to secure the slim optical drive retainer to the side of the new slim optical drive. Figure 43. Installing the slim optical drive retainer 4. Install the slim optical drive with the retainer into the 5.25-inch cage assembly. Press the tab at the front of the 5.25-inch cage assembly until you hear a click. The slim optical drive is secured in place. Figure 44. Installing the slim optical drive in the 5.
2. If you are replacing an old hard disk drive, remove the four screws that secure the hard disk drive. Then, slide the hard disk drive out of the rear of the 5.25-inch cage assembly. Figure 45. Removing the hard disk drive from the 5.25-inch cage assembly 3. To install a new hard disk drive, slide the new hard disk drive into the 5.25-inch cage assembly from the rear of the 5.25-inch cage assembly. Then install the four screws to secure the new hard disk drive in the 5.25-inch cage assembly. Figure 46.
Installing or replacing the fan of the 5.25-inch cage assembly To install or replace the fan on the 5.25-inch cage assembly, do the following: 1. Slide the 5.25-inch cage assembly out of the front of the computer. See “Installing or replacing a device in the optical drive bay” on page 78. 2. If you are replacing an old cage assembly fan, pivot the four retaining clips on the cage assembly fan bracket as shown to disengage the fan from the 5.25-inch cage assembly. Figure 47. Removing the fan from the 5.
1. Slide the 5.25-inch cage assembly out of the front of the computer. See “Installing or replacing a device in the optical drive bay” on page 78. 2. Remove the slim optical drive from the 5.25-inch cage assembly. See “Installing or replacing a slim optical drive in the 5.25-inch cage assembly” on page 88. 3. Remove the hard disk drive form the 5.25-inch cage assembly. See “Installing or replacing a hard disk drive in the 5.25-inch cage assembly” on page 90. 4.
What to do next: • To work with another piece of hardware, go to the appropriate section. • To complete the installation or replacement, go to “Completing the parts replacement” on page 125. Replacing the front audio and USB assembly Attention: Do not open your computer or attempt any repair before reading and understanding the “Read this first: Important safety information” on page v. To replace the front audio and USB assembly, do the following: 1.
7. Route the cables of the new front audio and USB assembly through the corresponding square hole in the front of the chassis. Then position the new front audio and USB assembly into the chassis and slide it to the left as shown. Install the screw to secure the new front audio and USB assembly in place. Figure 52. Installing the front audio and USB assembly 8. Connect the cables of the new front audio and USB assembly to the front audio connector and the front USB 3.0 connector on the system board.
5. Remove the old battery. Figure 53. Removing the old battery 6. Install a new battery. Figure 54. Installing a new battery 7. Reinstall the heat sink and fan assembly. See “Replacing the heat sink and fan assembly” on page 98. 8. Reinstall the computer cover and connect the cables. See “Completing the parts replacement” on page 125. Note: When the computer is turned on for the first time after replacing the battery, an error message might be displayed. This is normal after replacing the battery. 9.
Hazardous moving parts. Keep fingers and other body parts away. CAUTION: Never remove the cover on a power supply or any part that has the following label attached. Hazardous voltage, current, and energy levels are present inside any component that has this label attached. There are no serviceable parts inside these components. If you suspect a problem with one of these parts, contact a service technician. To replace the power supply assembly, do the following: 1.
6. Slide the power supply assembly to the front of the computer and then lift it out of the chassis. 7. Ensure that the new power supply assembly is the correct replacement. 8. Install the new power supply assembly into the chassis so that the screw holes in the power supply assembly align with those in the chassis. 9. Install and tighten the four screws to secure the power supply assembly. Note: Use only screws provided by Lenovo. 10.
6. Follow the following sequence to remove the four screws that secure the heat sink and fan assembly to the system board: a. Partially remove screw 1 , then fully remove screw 2 , and then fully remove screw 1 . b. Partially remove screw 3 , then fully remove screw 4 , and then fully remove screw 3 . Note: Carefully remove the four screws from the system board to avoid any possible damage to the system board. The four screws cannot be removed from the heat sink and fan assembly. Figure 56.
Installing or replacing the solid-state drive The solid-state drive is only available on some models. This section provides the following instructions: • “Installing the solid-state drive” on page 100 • “Replacing the solid-state drive” on page 101 Installing the solid-state drive Attention: Do not open your computer or attempt any repair before reading and understanding the “Read this first: Important safety information” on page v. To install the solid-state drive, do the following: 1.
3. Remove the 3.5–inch hard disk drive bracket for the chassis. 4. To install the storage converter together with the solid-state drive into the 3.5-inch hard disk drive bracket, flex the bracket and align pin 1 , pin 2 , pin 3 , and pin 4 on the bracket with the corresponding holes in the storage converter. Figure 58. Installing the storage converter together with the solid-state drive into the hard disk drive bracket 5. Install the storage converter with the bracket into the desired hard-disk-drive bay.
6. Flex the sides of the plastic 3.5–inch hard disk drive bracket to pull pins on the bracket out of the corresponding holes in the storage converter. Then remove the storage converter from the bracket. Figure 59. Removing the storage converter from the 3.5–inch hard disk drive bracket 7. Remove the four screws that secure the solid-state drive. Then lift the solid-state drive out of the storage converter. Figure 60.
8. Install a new solid-state drive into the storage converter. Then install the four screws to secure the new solid-state drive to the storage converter. Figure 61. Installing the new solid-state drive into the storage converter 9. To install the storage converter into the 3.5-inch hard disk drive bracket, flex the bracket and align pin 1 , pin 2 , pin 3 , and pin 4 on the bracket with the corresponding holes in the storage converter. Figure 62.
• To complete the installation or replacement, go to “Completing the parts replacement” on page 125. Installing or replacing the mSATA solid-state drive The mSATA solid-state drive is only available on some models.
3. Slide the storage converter into the mSATA solid-state drive bay until it snaps into position. Then install the screw to secure the storage converter to the chassis. Figure 65. Installing the storage converter with mSATA solid-state drive into the chassis 4. Connect the signal cable and the power cable to the mSATA solid-state drive. What to do next: • To work with another piece of hardware, go to the appropriate section.
7. Remove the two screws that secure the mSATA solid-state drive from the storage converter. Figure 67. Removing the screws that secure the mSATA solid-state drive 8. Remove the mSATA solid-state drive from the mini PCI Express slot on the storage converter. Figure 68. Removing the mSATA solid-state drive from the storage converter 9.
10. Install the two screws to secure the mSATA solid-state drive to the storage converter. Figure 70. Installing the screws to secure the mSATA solid-state drive 11. Slide the storage converter with the new mSATA solid-state drive into the mSATA solid-state drive bay until it snaps into position. Then install the screw to secure the storage converter to the chassis. Figure 71. Installing the mSATA solid-state drive 12. Connect the signal cable and the power cable to the new mSATA solid-state drive.
5. Pull the blue handle to release and remove the hard disk drive from the drive cage. Figure 72. Removing the primary hard disk drive 6. Flex the sides of the blue bracket to remove the hard disk drive from the bracket. 7. To install a new hard disk drive into the blue bracket, flex the bracket and align pin 1 , pin 2 , pin 3 , and pin 4 on the bracket with the corresponding holes in the hard disk drive. Do not touch the circuit board 5 on the bottom of the hard disk drive. Figure 73.
8. Slide the new hard disk drive into the drive cage until it snaps into position. Figure 74. Installing the primary hard disk drive 9. Connect the signal cable and the power cable to the new hard disk drive. What to do next: • To work with another piece of hardware, go to the appropriate section. • To complete the installation or replacement, go to “Completing the parts replacement” on page 125.
6. Flex the sides of the blue bracket to remove the hard disk drive from the bracket. 7. To install a new hard disk drive into the blue bracket, flex the bracket and align pin 1 , pin 2 , pin 3 , and pin 4 on the bracket with the corresponding holes in the hard disk drive. Do not touch the circuit board 5 on the bottom of the hard disk drive. Figure 76. Installing the hard disk drive into the bracket 8. Slide the new hard disk drive into the drive cage until it snaps into position. Figure 77.
To install a tertiary 3.5-inch hard disk drive or a 2.5-inch solid-state drive, do the following: 1. Remove all media from the drives and turn off all attached devices and the computer. Then, disconnect all power cords from electrical outlets and disconnect all cables that are connected to the computer. 2. Remove the computer cover. See “Removing the computer cover” on page 71. 3. Remove the front bezel. See “Removing and reinstalling the front bezel” on page 72. 4.
a. Install the solid-state drive into the storage converter. Then, install the five screws to secure the solid-state drive to the storage converter. Figure 79. Installing the solid-state drive into the storage converter b. Install the solid-state drive with the storage converter into the 5.25-inch optical drive bracket. Then, fully tighten the four screws to secure the solid-state drive with the storage converter to the 5.25-inch optical drive bracket. Figure 80.
6. Install the optical drive retainer on the side of the optical drive bracket. Figure 81. Installing the optical drive retainer 7. Slide the optical drive bracket into the secondary optical-drive bay from the front of the computer until the optical drive bracket snaps into position. Figure 82. Installing the optical drive bracket 8. Connect the signal cable and the power cable to the new hard disk drive or solid-state drive. Figure 83.
Replacing the front fan assembly Attention: Do not open your computer or attempt any repair before reading and understanding the “Read this first: Important safety information” on page v. Note: The front fan assembly is only available on some models. To replace the front fan assembly, do the following: 1. Remove all media from the drives and turn off all attached devices and the computer. Then, disconnect all power cords from electrical outlets and disconnect all cables that are connected to the computer.
8. Connect the front fan assembly cable to the power fan connector on the system board. What to do next: • To work with another piece of hardware, go to the appropriate section. • To complete the installation or replacement, go to “Completing the parts replacement” on page 125. Replacing the rear fan assembly Attention: Do not open your computer or attempt any repair before reading and understanding the “Read this first: Important safety information” on page v.
7. Pull on the tips of the rubber mounts until the rear fan assembly is secured in place. Figure 87. Installing the rear fan assembly 8. Connect the rear fan assembly cable to the system fan connector on the system board. What to do next: • To work with another piece of hardware, go to the appropriate section. • To complete the installation or replacement, go to “Completing the parts replacement” on page 125.
3. If your computer comes with a Wi-Fi card module that supports the Bluetooth function, disconnect the Bluetooth cable from the Wi-Fi adapter card. Figure 88. Disconnecting the Bluetooth cable Note: The Bluetooth cable connects the Bluetooth connector on the Wi-Fi adapter card to the front USB connector on the system board to support the Bluetooth function. 4. At the rear of the computer, press the release button 1 to open the PCI card latch 2 . Figure 89. Opening the PCI card latch Chapter 9.
5. Grasp the Wi-Fi adapter card that is currently installed and gently pull it out of the slot. Figure 90. Removing the Wi-Fi adapter card Note: The card fits tightly into the card slot. If necessary, alternately move each side of the card a small amount until it is removed from the card slot. Removing the Wi-Fi card module To remove the Wi-Fi card module, do the following: 1.
2. Remove the two screws that secure the Wi-Fi card module to the Wi-Fi adapter card. Figure 92. Removing the screws that secure the Wi-Fi card module 3. Pull the Wi-Fi card module out of the mini PCI Express slot to remove it from the Wi-Fi adapter card. Figure 93. Removing the Wi-Fi card module Installing the Wi-Fi units To install the Wi-Fi units, do the following: Chapter 9.
1. Insert the Wi-Fi card module into the mini PCI Express slot, and then install the two screws to secure the Wi-Fi card module to the Wi-Fi adapter card. Figure 94.
2. Connect the front antenna cable and rear antenna cable to the Wi-Fi card module. Figure 95. Installing the Wi-Fi antenna cables 3. Install the Wi-Fi adapter card into the PCI Express x1 slot on the system board. See “Locating parts on the system board” on page 6. 4. If the installed Wi-Fi card module supports the Bluetooth function, use a Bluetooth cable to connect the Bluetooth connector on the Wi-Fi adapter card to the front USB connector on the system board. 5.
1. Remove all media from the drives and turn off all attached devices and the computer. Then, disconnect all power cords from electrical outlets and disconnect all cables that are connected to the computer. 2. Install the rear Wi-Fi antenna to the rear Wi-Fi antenna cable connector attached on the rear of the computer. 3. Adjust the angle of the rear antenna to lower the risk of breaking the antenna by accident. Figure 97.
Installing or removing the front Wi-Fi antenna Attention: Do not open your computer or attempt any repair before reading and understanding the “Read this first: Important safety information” on page v. Installing the front Wi-Fi antenna To install the front Wi-Fi antenna, do the following: 1. Remove all media from the drives and turn off all attached devices and the computer. Then, disconnect all power cords from electrical outlets and disconnect all cables that are connected to the computer. 2.
What to do next: • To work with another piece of hardware, go to the appropriate section. • To complete the installation or replacement, go to “Completing the parts replacement” on page 125. Removing the front Wi-Fi antenna To remove the front Wi-Fi antenna, do the following: 1. Remove all media from the drives and turn off all attached devices and the computer. Then, disconnect all power cords from electrical outlets and disconnect all cables that are connected to the computer. 2.
What to do next: • To work with another piece of hardware, go to the appropriate section. • To complete the installation or replacement, go to “Completing the parts replacement” on page 125. Completing the parts replacement After completing the installation or replacement for all parts, you need to reinstall the computer cover and reconnect cables. Depending on the parts you installed or replaced, you might need to confirm the updated information in the Setup Utility program.
7. Reconnect the external cables and power cords to the computer. See “Locating connectors on the rear of your computer” on page 3. 8. To update your configuration, refer to “Using the Setup Utility program” on page 37. Note: In most areas of the world, Lenovo requires the return of the defective CRU. Information about this will come with the CRU or will come a few days after the CRU arrives.
Chapter 10. Getting information, help, and service This chapter contains information about help, service, and technical assistance for products manufactured by Lenovo. Information resources You can use the information in this section to access useful resources relating to your computing needs. Lenovo ThinkVantage Tools The Lenovo ThinkVantage Tools program guides you to a host of information sources and provides easy access to various tools to help you work more easily and securely.
• Access troubleshooting and support information for your computer model and other supported products. • Find the service and support phone numbers for your country or region. • Find a Service Provider located near you. Lenovo Support Web site Technical support information is available on the Lenovo Support Web site at: http://www.lenovo.
• • • • • • Replacement or use of parts not manufactured for or by Lenovo or non-warranted Lenovo parts Identification of software problem sources Configuration of BIOS as part of an installation or upgrade Changes, modifications, or upgrades to device drivers Installation and maintenance of network operating systems (NOS) Installation and maintenance of application programs Refer to the Safety, Warranty, and Setup Guide that comes with your computer for information about your warranty type and duration.
130 ThinkStation P300 User Guide
System memory speed The Intel Xeon® microprocessor families compatible with this ThinkStation® computer feature an integrated memory controller, which provides the microprocessor with direct access to the system memory. Because of this design, the system memory speed will be determined by a number of factors, including the microprocessor model and the type, speed, size (capacity), and number of DIMMs installed.
2 ThinkStation P300 User Guide
Appendix A. Regulatory information Export classification notice This product is subject to the United States Export Administration Regulations (EAR) and has an Export Classification Control Number (ECCN) of 4A994.b. It can be re-exported except to any of the embargoed countries in the EAR E1 country list. Electronic emissions notices The following information refers to Lenovo personal computer machine types 10DA, 30AG, and 30AH.
This product is in conformity with the protection requirements of EU Council Directive 2004/108/EC on the approximation of the laws of the Member States relating to electromagnetic compatibility. Lenovo cannot accept responsibility for any failure to satisfy the protection requirements resulting from a non-recommended modification of the product, including the installation of option cards from other manufacturers.
Japan VCCI Class B compliance statement Japan compliance statement for products which connect to the power mains with rated current less than or equal to 20 A per phase Japan notice for ac power cord The ac power cord shipped with your product can be used only for this specific product. Do not use the ac power cord for other devices.
6 ThinkStation P300 User Guide
Appendix B. WEEE and recycling information Lenovo encourages owners of information technology (IT) equipment to responsibly recycle their equipment when it is no longer needed. Lenovo offers a variety of programs and services to assist equipment owners in recycling their IT products. For information on recycling Lenovo products, go to: http://www.lenovo.
Disposing of Lenovo computer components Some Lenovo computer products sold in Japan may have components that contain heavy metals or other environmental sensitive substances. To properly dispose of disused components, such as a printed circuit board or drive, use the methods described above for collecting and recycling a disused computer or monitor.
Batteries or packaging for batteries are labeled in accordance with European Directive 2006/66/EC concerning batteries and accumulators and waste batteries and accumulators. The Directive determines the framework for the return and recycling of used batteries and accumulators as applicable throughout the European Union. This label is applied to various batteries to indicate that the battery is not to be thrown away, but rather reclaimed upon end of life per this Directive.
10 ThinkStation P300 User Guide
Appendix C. Restriction of Hazardous Substances Directive (RoHS) European Union RoHS Lenovo products sold in the European Union, on or after 3 January 2013 meet the requirements of Directive 2011/65/EU on the restriction of the use of certain hazardous substances in electrical and electronic equipment (“RoHS recast” or “RoHS 2”). For more information about Lenovo progress on RoHS, go to: http://www.lenovo.com/social_responsibility/us/en/RoHS_Communication.
Ukraine RoHS India RoHS RoHS compliant as per E-Waste (Management & Handling) Rules, 2011.
Appendix D. ENERGY STAR model information ENERGY STAR® is a joint program of the U.S. Environmental Protection Agency and the U.S. Department of Energy aimed at saving money and protecting the environment through energy efficient products and practices. Lenovo is proud to offer our customers products with an ENERGY STAR compliant designation.
14 ThinkStation P300 User Guide
Appendix E. Notices Lenovo may not offer the products, services, or features discussed in this document in all countries. Consult your local Lenovo representative for information on the products and services currently available in your area. Any reference to a Lenovo product, program, or service is not intended to state or imply that only that Lenovo product, program, or service may be used.
Trademarks The following terms are trademarks of Lenovo in the United States, other countries, or both: Lenovo Rescue and Recovery The Lenovo logo The ThinkStation logo ThinkStation ThinkVantage Microsoft, Windows, and Windows Media are trademarks of the Microsoft group of companies. Intel and Xeon are trademarks of Intel Corporation in the U.S. and/or other countries. Linux is a registered trademark of Linus Torvalds. DisplayPort is a Trademark of the Video Electronics Standards Association.
Index A a rescue medium, creating and using Administrator, password 38 Advance configuration 37 audio features 9 audio line-in connector 4 audio line-out connector 4 B backup and recovery operations basic troubleshooting 51 battery, replacing 95 boot-block recovery 44 64 C cable lock, security 32–33 changing password 39 startup device sequence 40 cleaning an optical mouse 49 CMOS, clearing 39 Companion 14 components, internal 5 computer cover removing 71 computer cover, reinstalling 125 connector 4 conne
Input/Output (I/O) features installing mSATA solid-state drive solid-state drive 100 installing options memory module 76 PCI card 73 internal drives 9 erasing 39 lost or forgotten 39 passwords, using 38 PCI card 73 installing, replacing 73 slots 73 physical specifications 12 power features 10 power supply assembly, replacing 96 power-on self-test (POST) 42 Power-on, password 38 programs, updating system 42 purchasing additional services 129 9 104 K Kensington-style cable lock 32 keyboard connector keyboa
purchasing additional 129 setting password 39 settings changing 37 viewing 37 Setup Utility 37 Setup Utility program, starting 37 Setup Utility, exiting 42 slim optical drive, card reader, eSATA connector, IEEE 1394 connector, replacing 81 slim optical drive, hard disk drive 88 software recovering 63 solid-state drive, installing 100 solid-state drive, replacing 101 solving recovery problems 68 speed, memory 1 starting the Setup Utility program 37 startup device 40 sequence, changing 40 temporary, selecting
20 ThinkStation P300 User Guide
