ThinkStation User Guide
Note Before using this information and the product it supports, be sure to read and understand the ThinkStation Safety and Warranty Guide and Appendix B, “Notices,” on page 77. First Edition (June 2010) © Copyright Lenovo 2010. LENOVO products, data, computer software, and services have been developed exclusively at private expense and are sold to governmental entities as commercial items as defined by 48 C.F.R. 2.101 with limited and restricted rights to use, reproduction and disclosure.
Contents Important safety information . . . . . . v Chapter 1. Product overview . . . . . . 1 Features . . . . . . . . . . . . . . . . 1 Specifications . . . . . . . . . . . . . . 4 Software overview . . . . . . . . . . . . 4 Software provided with your Windows operating system . . . . . . . . . . . . . . . 4 Locating computer controls, connectors, and parts . . 6 Locating controls and connectors on the front of your computer. . . . . . . . . . . . .
Information resources . . . . . . . . . Online Books folder . . . . . . . . Lenovo ThinkVantage Tools . . . . . . Lenovo Welcome . . . . . . . . . Safety and warranty . . . . . . . . Lenovo Web site (http://www.lenovo.com). Help and service . . . . . . . . . . Using the documentation and diagnostic programs . . . . . . . . . . . . Calling for service . . . . . . . . . Using other services . . . . . . . . iv User Guide . . . . . . . . . . . . . . 71 71 71 72 72 72 72 . . . . 72 . 73 .
Important safety information CAUTION: Before using this manual, be sure to read and understand all the related safety information for this product. Refer to the ThinkStation Safety and Warranty Guide that you received with this product for the latest safety information. Reading and understanding this safety information reduces the risk of personal injury and or damage to your product.
vi User Guide
Chapter 1. Product overview This chapter provides information about the computer features, specifications, preinstalled software programs, and connector and part locations. This chapter contains the following topics: v “Features”: This section provides information about the computer features. v “Specifications” on page 4: This section lists the physical specifications for your computer.
Video subsystem v Two Peripheral Component Interconnect (PCI) Express x16 card slots on the system board for discrete graphics cards (varies by model type) Audio subsystem v Integrated high-definition (HD) audio v Microphone connector and headphone connector on the front panel v Eight audio connectors on the rear panel – Audio line-in connector – Audio line-out front speaker connector – Audio line-out rear speaker connector – Audio line-out side speaker connector – Audio line-out subwoofer/center speaker co
Expansion v One optical drive bay v One PCI Express x1 card slot v One PCI Express x4 card slot (x16 mechanical) v Three hard disk drives v Two PCI card slots v Two PCI Express x16 card slots Power supply v 800-watt auto-sensing power supply Security features v Cover presence switch (also called intrusion switch) (available in some models) v Enabling or disabling SATA devices v Enabling or disabling the serial port v Enabling or disabling USB connectors individually v User password and administrator passwor
Specifications This section lists the physical specifications for your computer. Dimensions Width: 130 mm (5.12 inches) Height: 427 mm (16.81 inches) Depth: 444 mm (17.48 inches) Weight Maximum configuration: 18.5 kg (40.8 lbs) Environment Air temperature: Operating: 10° to 35°C (50° to 95°F) Non-operating: -10° to 60°C (14° to 140°F) (with package) Humidity: Operating: 10% to 80% (10% per hour, non-condensing) Non-operating: 10% to 90% (10% per hour, non-condensing) Maximum altitude: 7 000 ft (2 133.
Note: The Lenovo ThinkVantage Tools program is only available on computers with the Windows 7 operating system from Lenovo. Lenovo Welcome: The Lenovo Welcome program introduces some innovative built-in features of Lenovo to you and guides you through some important setup tasks to help you make the most of your computer. Note: The Lenovo Welcome program is only available on computers preinstalled with the Windows 7 operating system from Lenovo.
Locating computer controls, connectors, and parts This section provides information to help you locate your computer controls, connectors, and parts. Locating controls and connectors on the front of your computer Figure 1 shows the locations of the controls and connectors on the front of your computer. Figure 1.
Locating connectors on the rear of your computer Figure 2 shows the locations of the connectors on the rear of your computer. Some connectors on the rear of your computer are color-coded to help you determine where to connect the cables on your computer. Figure 2.
Connector Description Audio line-in connector Used to receive audio signals from an external audio device, such as a stereo system. When you attach an external audio device, a cable is connected between the audio line-out connector of the device and the audio line-in connector of the computer.
Connector Description Optical SPDIF in connector Used to receive 5.1 digital audio signals from an external device (such as a receiver or a multimedia device) through a TOSLINK (ToshibaLink) optical cable. Optical SPDIF out connector Used to send 5.1 digital audio signals from a computer to an external device (such as an amplifier or a receiver) through a TOSLINK optical cable.
Locating components Figure 3 shows the locations of the various components in your computer. To remove the computer cover and access the inside of the computer, see “Removing the computer cover” on page 13. Figure 3.
Locating parts and connectors on the system board Note: Your computer comes with one of the following system boards. Figure 4 shows the locations of the parts and connectors on one type of system board. 35 34 33 32 31 Figure 4.
Figure 5 shows the locations of the parts and connectors on the other type of system board. Figure 5.
Chapter 2. Installing or replacing hardware This chapter provides instructions on how to install or replace hardware for your computer. This chapter contains the following topics: v “Installing or replacing hardware” v “Obtaining device drivers” on page 41 v “Basic security features” on page 42 Installing or replacing hardware This section provides instructions on how to install or replace hardware for your computer.
This section provides instructions on how to remove the computer cover. CAUTION: Turn off the computer and wait three to five minutes to let the computer cool before removing the computer cover. To remove the computer cover, do the following: 1. Remove all media from the drives and turn off all attached devices and the computer. Then, disconnect all power cords from electrical outlets and disconnect all cables that are connected to the computer. 2.
Removing and reinstalling the front bezel Attention Do not open your computer or attempt any repair before reading and understanding the “Important safety information” in the ThinkStation Safety and Warranty Guide that came with your computer. To obtain a copy of the ThinkStation Safety and Warranty Guide, go to: http://www.lenovo.com/support This section provides instructions on how to remove and reinstall the front bezel. To remove and reinstall the front bezel, do the following: 1.
Removing and reinstalling the PCI card holder Attention Do not open your computer or attempt any repair before reading and understanding the “Important safety information” in the ThinkStation Safety and Warranty Guide that came with your computer. To obtain a copy of the ThinkStation Safety and Warranty Guide, go to: http://www.lenovo.com/support This section provides instructions on how to remove and reinstall the PCI card holder. To remove and reinstall the PCI card holder, do the following: 1.
6. To reinstall the PCI card holder into the chassis, insert the two tabs 1 into the corresponding holes in the chassis, and then pivot the PCI card holder downward until the front of the card holder snaps into position. Figure 9. Installing the PCI card holder Installing or replacing a memory module Attention Do not open your computer or attempt any repair before reading and understanding the “Important safety information” in the ThinkStation Safety and Warranty Guide that came with your computer.
v Use 1 GB, 2 GB, 4 GB, 8 GB, or 16 GB RDIMMs in any combination up to a maximum of 96 GB or 192 GB of system memory. v Always install DIMMs in the numerical order printed on the system board (DIMM1, DIMM2, DIMM3, and so on). Install memory modules into the blue memory slots first. v If your computer has only one CPU installed, be sure to install memory modules only in the memory slots adjacent to that CPU.
memory fan cable from the system board, remove the blue shipping clip, press inward on the two tabs 1 , pivot the fan duct, and then disengage the rear of the fan duct. Note: Not all computer models have the memory fan duct and blue shipping clip. Figure 11. Removing the memory fan duct 7. Open the retaining clips as shown. Figure 12. Opening the retaining clips If you are replacing an old memory module, open the retaining clips and gently pull the memory module out of the memory slot. Figure 13.
Notes: a. If your computer has 12 memory slots on the system board, you might have to use more force to remove the memory modules installed in memory slots 1 and 2 . b. If your computer has six memory slots on the system board, you might have to use more force to remove the memory module installed in memory slot 1 .
8. Position the new memory module over the memory slot. Make sure that the notch 1 on the memory module aligns correctly with the key 2 in the memory slot. Push the memory module straight down into the slot until the retaining clips close. Figure 14. Installing a memory module 9. To install the memory fan duct, engage the rear of the duct with the retainer on the system board and then pivot the fan duct downward until the fan duct snaps into position.
Installing or replacing a PCI card Attention Do not open your computer or attempt any repair before reading and understanding the “Important safety information” in the ThinkStation Safety and Warranty Guide that came with your computer. To obtain a copy of the ThinkStation Safety and Warranty Guide, go to: http://www.lenovo.com/support This section provides instructions on how to install or replace a PCI card.
b. If the card is held in place by a retaining latch, press the card retaining latch 1 as shown to disengage the latch. Grasp the card and then gently pull it out of the slot. 5. Remove the new PCI card from its static-protective package. 6. Install the new PCI card into the appropriate slot on the system board. See “Locating parts and connectors on the system board” on page 11. Figure 17. Installing a new PCI card 7. Reinstall the PCI card holder into the chassis.
Installing a new hard disk drive Attention Do not open your computer or attempt any repair before reading and understanding the “Important safety information” in the ThinkStation Safety and Warranty Guide that came with your computer. To obtain a copy of the ThinkStation Safety and Warranty Guide, go to: http://www.lenovo.com/support This section provides instructions on how to install a new hard disk drive into your computer. To install a new hard disk drive, do the following: 1.
7. Connect one end of the signal cable that comes with the new hard disk drive to the rear of the new hard disk drive. Note: The signal cable will be different depending on whether you are installing a SATA hard disk drive or a SAS hard disk drive. Figure 19. Connecting the signal cable to a SATA hard disk drive Figure 20. Connecting the signal cable to a SAS hard disk drive Chapter 2.
8. Slide the new hard disk drive with the bracket and the signal cable into the hard disk drive bay until it snaps into position. Figure 21.
9. Locate one of the extra five-wire power cables and connect it to the new hard disk drive. Note: You might need to disconnect power cables for other hard disk drives installed in your computer and then rotate the air flow wall outward for easier access to the rear of the new hard disk drive. Figure 22. Rotating the air flow wall 10. Connect the other end of the signal cable to one of the available hard disk drive connectors on the system board.
Replacing a hard disk drive Attention Do not open your computer or attempt any repair before reading and understanding the “Important safety information” in the ThinkStation Safety and Warranty Guide that came with your computer. To obtain a copy of the ThinkStation Safety and Warranty Guide, go to: http://www.lenovo.com/support This section provides instructions on how to replace a hard disk drive. To replace a hard disk drive, do the following: 1.
7. To install a new hard disk drive, go to “Installing a new hard disk drive” on page 24. What to do next: v To work with another piece of hardware, go to the appropriate section. v To complete the installation or replacement, go to “Completing the parts replacement” on page 40. Replacing the optical drive Attention Do not open your computer or attempt any repair before reading and understanding the “Important safety information” in the ThinkStation Safety and Warranty Guide that came with your computer.
4. Disconnect the signal cable and the power cable from the rear of the optical drive, press the blue release button 1 as shown, and then slide the optical drive out of the computer. Figure 24. Removing the optical drive 5. Install the optical drive retainer 1 on the side of the new optical drive. Then, slide the new optical drive into the optical drive bracket from the front of the computer until the optical drive snaps into position. Figure 25. Installing the new optical drive 6.
Then, disconnect the old signal cable from the system board. Connect one end of the new signal cable to the optical drive and the other end to an available SATA connector on the system board. See “Locating parts and connectors on the system board” on page 11. b. Locate an available five-wire power connector and connect it to the new optical drive. Figure 26. Connecting a new optical drive 7. Reinstall the PCI card holder into the chassis if you have removed it.
1. Remove all media from the drives and turn off all attached devices and the computer. Then, disconnect all power cords from electrical outlets and disconnect all cables that are connected to the computer. 2. Remove the computer cover. See “Removing the computer cover” on page 13. 3. Remove the PCI card holder. See “Removing and reinstalling the PCI card holder” on page 16. 4. Your computer supports two heat sink and fan assemblies. Locate the heat sink and fan assembly you want to replace.
7. Follow this sequence to remove the four screws that secure the heat sink and fan assembly to the system board: a. Partially remove screw 1 , then fully remove screw 2 , and then fully remove screw 1 . b. Partially remove screw 3 , then fully remove screw 4 , and then fully remove screw 3 . Note: Carefully remove the four screws from the system board to avoid any possible damage to the system board. The four screws cannot be removed from the heat sink and fan assembly. Figure 28.
10. Position the new heat sink and fan assembly on the microprocessor so that the four screws are aligned with the holes in the system board. Note: Position the new heat sink and fan assembly so that the heat sink and fan assembly cable is toward the microprocessor fan connector on the system board. 11. Follow this sequence to install the four screws to secure the new heat sink and fan assembly: a. Partially tighten screw 1 , then fully tighten screw 2 , and then fully tighten screw 1 . b.
5. Disconnect the front fan assembly cable from the front fan connector on the system board. See “Locating parts and connectors on the system board” on page 11. 6. Press the two tabs 1 that attach the front fan assembly bracket to the chassis toward each other as shown and then completely remove the front fan assembly bracket from the chassis. Figure 29. Removing the front fan assembly bracket Chapter 2.
7. Insert the two tabs 1 on the new front fan assembly bracket into the corresponding holes in the chassis, and then press the two tabs through the holes until the bracket is secured in place. Figure 30. Installing the new front fan assembly bracket 8. Connect the front fan assembly cable to the front fan connector on the system board. See “Locating parts and connectors on the system board” on page 11. What to do next: v To work with another piece of hardware, go to the appropriate section.
Replacing the rear fan assembly Attention Do not open your computer or attempt any repair before reading and understanding the “Important safety information” in the ThinkStation Safety and Warranty Guide that came with your computer. To obtain a copy of the ThinkStation Safety and Warranty Guide, go to: http://www.lenovo.com/support This section provides instructions on how to replace the rear fan assembly. Note: Your computer supports two rear fan assemblies.
7. The rear fan assembly is attached to the chassis by four rubber mounts. Remove the rear fan assembly by breaking or cutting the rubber mounts and gently pulling the rear fan assembly out of the chassis. Figure 31. Removing the rear fan assembly 8. Install the new rear fan assembly by aligning the new rubber mounts with the corresponding holes in the chassis and push the rubber mounts through the holes. Note: The new rear fan assembly you received will have four new rubber mounts attached.
9. Pull on the tips of the rubber mounts until the rear fan assembly is secured in place. Figure 32. Installing the rear fan assembly 10. Connect the rear fan assembly cable to the appropriate rear fan connector on the system board. See “Locating parts and connectors on the system board” on page 11. What to do next: v To work with another piece of hardware, go to the appropriate section. v To complete the installation or replacement, go to “Completing the parts replacement” on page 40.
This section provides instructions on how to replace the keyboard or mouse. To replace the keyboard or mouse, do the following: 1. Remove any media from the drives. Then, turn off all attached devices and the computer. 2. Disconnect all power cords from electrical outlets. 3. Disconnect the old keyboard cable or mouse cable from the computer. 4. Connect a new keyboard or mouse to one of the USB connectors on the computer.
5. Position the computer cover on the chassis so that the rail guides on the bottom of the computer cover engage with the rails on the chassis. Then, close the computer cover to engage the cover-release button. Figure 34. Reinstalling the computer cover 6. Use the keys that came with your computer to lock the keylock in the computer cover. See “Locking devices” on page 42. 7. Lock the computer if you have an integrated cable lock or a padlock. See “Locking devices” on page 42. 8.
Basic security features There are several security options available to help you prevent hardware theft and unauthorized access to your computer. In addition to physical locks, you can also prevent unauthorized use of your computer by a software lock that locks the keyboard until a correct password is typed in. Locking devices Note: Make sure that any security cables you installed do not interfere with other computer cables. This section describes the different kinds of locking devices for your computer.
used with many notebook computers. You can order an integrated cable lock from Lenovo by searching for Kensington at: http://www.lenovo.com/support Your computer comes with a keylock 3 , which was built into the computer cover. The keys for the computer cover are attached to the rear of the machine. For security, store the keys in a secure place when you are not using them. Password protection To deter unauthorized use of your computer, you can use the Setup Utility program to set a password.
44 User Guide
Chapter 3. Recovery information This chapter provides information about the recovery solutions provided by Lenovo. This chapter contains the following topics: v “Creating and using recovery media” v “Performing backup and recovery operations” on page 47 v v v v “Using the Rescue and Recovery workspace” on page 48 “Creating and using a rescue medium” on page 49 “Installing or reinstalling device drivers” on page 50 “Solving recovery problems” on page 51 Notes: 1.
v To create Product Recovery discs on the Windows XP operating system, click Start → All Programs → ThinkVantage → Create Recovery Media. Then, follow the instructions on the screen. Using recovery media This section provides instructions on how to use recovery media on different operating systems. v On the Windows 7 operating system, you can use recovery media to restore the computer to the factory default settings only.
Performing backup and recovery operations The Rescue and Recovery program enables you to back up all your hard disk drive contents including the operating system, data files, software programs, and personal settings.
v To perform a recovery operation using the Rescue and Recovery program on the Windows XP operating system, do the following: 1. From the Windows desktop, click Start → All Programs → ThinkVantage → Rescue and Recovery. The Rescue and Recovery program opens. 2. In the Rescue and Recovery main window, click Launch advanced Rescue and Recovery. 3. Click the Restore your system from a backup icon. 4. Follow the instructions on the screen to complete the recovery operation.
Note: If the Rescue and Recovery workspace fails to open, see “Solving recovery problems” on page 51. 4. Do one of the following: v To rescue files from your hard disk drive or from a backup, click Rescue files and follow the instructions on the screen. v To restore your hard disk drive from a Rescue and Recovery backup or to restore your hard disk drive to the factory default settings, click Restore your system and follow the instructions on the screen.
v To create a rescue medium on the Windows XP operating system, do the following: 1. From the Windows desktop, click Start → All Programs → ThinkVantage → Create Recovery Media. The Create Rescue and Recovery Media window opens. 2. In the Rescue Media area, select the type of the rescue medium you want to create. You can create a rescue medium using a disc, a USB hard disk drive, or a secondary internal hard disk drive. 3. Click OK and follow the instructions on the screen to create a rescue medium.
drivers for factory-installed devices are also available at http://www.lenovo.com/ support. Other device drivers are on the software media that come with individual devices. To install or reinstall the device driver for a factory-installed device, do the following: 1. Turn on the computer. 2. Use Windows Explorer or My Computer to display the directory structure of your hard disk drive. 3. Go to the C:\SWTOOLS directory. 4. Open the DRIVERS folder.
52 User Guide
Chapter 4. Using the Setup Utility program You can use the Setup Utility program to view and change the configuration settings of your computer, regardless of which operating system you are using. However, the operating system settings might override any similar settings in the Setup Utility program.
You do not have to set a password to use your computer. However, using a password improves computing security. If you decide to set a password, read the following sections. Password considerations A password can be any combination of up to 12 (1 to 12) alphabetic and numeric characters. For security reasons, it is recommended to use a strong password that cannot be easily compromised. To set a strong password, use the following guidelines: Note: The Setup Utility program passwords are not case sensitive.
Enabling or disabling a device This section provides instructions on how to enable or disable user access to a device. USB Support Use this option to enable or disable USB connectors. ICH SATA When this feature is set to Disabled, any optical drives or eSATA devices are disabled and will not be displayed in the system configuration. Marvell SATA/SAS controller When this feature is set to Disabled, all internal hard disk drives are disabled and will not be displayed in the system configuration.
2. Repeatedly press and release the F12 key when turning on the computer. When the Startup Device Menu opens, release the F12 key. 3. Select the desired startup device on the Startup Device Menu and press Enter to begin. Note: Selecting a startup device on the Startup Device Menu does not permanently change the startup device sequence. Viewing or changing the startup device sequence This section provides instructions on how to view or permanently change the configured startup device sequence.
Chapter 5. Configuring RAID This chapter contains information about installing hard disk drives and configuring Redundant Array of Independent Disks (RAID) for your computer. Notes: 1. The Marvell BIOS setup information in this chapter only applies to some computer models. 2. The information about configuring RAID in this chapter only applies for a Windows environment. For information about configuring RAID in a Linux environment, contact your Linux software provider.
5. Press F10 to save the new settings and exit the Setup Utility program. Creating RAID volumes This section describes how to use the Intel Matrix Storage Manager option ROM configuration utility to create RAID volumes. 1. Press Ctrl+I when prompted to enter the Intel Matrix Storage Manager option ROM configuration utility. 2. Use the up and down arrow keys to select Create RAID Volume and press Enter. 3. Type a proper RAID Volume name in the Name field and press Tab. 4.
Configuring RAID for machine types 4266, 4269, 4271, and 4272 This section contains information about the required number of SATA or SAS hard disk drives for the supported level of RAID and SATA or SAS RAID configuration for machine types 4266, 4269, 4271, and 4272. Note: Your computer must have either all SATA hard disk drives or all SAS hard disk drives installed. However, be sure that you do not install both the SATA and SAS hard disk drives into the same computer.
4. Use the arrow keys and the Enter key to select each free hard disk drive that you want to include in the array. 5. Select Next and press Enter. 6. From the Create array menu, select RAID level and press Enter. Note: Only the valid RAID levels will be active. 7. Select your desired RAID level (RAID 0, RAID 1, or RAID 5) and press Enter. 8. From the Stripe Size menu, you can change the stripe size or keep it as default. 9. Type a proper array name in the Array Name field. 10. Select Next and press Enter.
3. From the RAID Config menu, select Delete array. 4. Use the arrow keys and the Enter key to select the array you want to delete from the list. 5. Use the arrow keys to select Next and press Enter. 6. Press Y when prompted to complete the deletion. Chapter 5.
62 User Guide
Chapter 6. Updating system programs This chapter provides information about updating the POST and BIOS, and how to recover from a POST and BIOS update failure. This chapter contains the following topics: v “Using system programs” v “Updating (flashing) the BIOS from a disc” v “Updating (flashing) the BIOS from your operating system” on page 64 Using system programs System programs are the basic layer of software built into your computer.
4. When prompted to change the serial number, it is suggested that you press N. However, if you do want to change the serial number, press Y, then type in the serial number and press Enter. 5. When prompted to change the machine type and model, it is suggested that you press N. However, if you do want to change the machine type and model, press Y, then type in the machine type and model and press Enter. 6. Follow the instructions on the screen to complete the update.
9. Reinstall the computer cover and reconnect the power cords for the computer and monitor to electrical outlets. Refer to “Completing the parts replacement” on page 40. 10. Turn on the computer and the monitor. Insert the POST/BIOS update (flash) disc into the optical drive. The recovery session begins. The recovery session will take two to three minutes. During this time, you will hear a series of beeps. 11.
66 User Guide
Chapter 7. Troubleshooting and diagnostic programs This chapter provides information about some basic troubleshooting and diagnostic programs. If your computer problem is not described in this chapter, see Chapter 8, “Getting information, help, and service,” on page 71 for additional troubleshooting resources.
Diagnostic programs Diagnostic programs are used to test hardware components of your computer. Diagnostic programs can also report operating-system-controlled settings that interfere with the correct operation of your system.
For additional information about running the PC-Doctor for Rescue and Recovery program, refer to the PC-Doctor for Rescue and Recovery help system. Note: If you encounter failures that prevent you from gaining access to the Rescue and Recovery workspace, you can run the PC-Doctor for Rescue and Recovery program after using a rescue medium to recover the computer from failures and gaining access to the Rescue and Recovery workspace. See “Creating and using a rescue medium” on page 49.
1. Turn off your computer. 2. Disconnect the mouse cable from the computer. 3. Turn the mouse upside down to view the lens. a. If there is a smudge on the lens, gently clean the area with a plain cotton-tipped swab. b. If there is debris in the lens, gently blow the debris away from the area. 4. Check the surface on which you are using the mouse.
Chapter 8. Getting information, help, and service This chapter provides information about help, service, and technical assistance for Lenovo products. This chapter contains the following topics: v “Information resources” v “Help and service” on page 72 Information resources You can use the information in this section to access useful resources relating to your computing needs.
To access the Lenovo ThinkVantage Tools program, click Start → All Programs → Lenovo ThinkVantage Tools. Lenovo Welcome Note: The Lenovo Welcome program is only available on computers preinstalled with the Windows 7 operating system from Lenovo. The Lenovo Welcome program introduces some innovative built-in features of Lenovo to you and guides you through some important setup tasks to help you make the most of your computer.
Most computers come with a set of diagnostic programs that you can use to help you identify hardware problems. For instructions on using the diagnostic programs, see “Diagnostic programs” on page 68. You can get the latest technical information and download device drivers and updates from the Lenovo Support Web site at: http://www.lenovo.com/support Calling for service During the warranty period, you can get help and information by telephone through the Customer Support Center.
International Warranty Service, which automatically entitles you to obtain warranty service throughout the warranty period. Service will be performed by service providers authorized to perform warranty service. Service methods and procedures vary by country, and some services might not be available in all countries. International Warranty Service is delivered through the method of service (such as depot, carry-in, or on-site service) that is provided in the servicing country.
Appendix A. System memory speed The Intel Xeon microprocessor families compatible with this ThinkStation computer feature an integrated memory controller, which provides the microprocessor with direct access to the system memory. Because of this design, the system memory speed will be determined by a number of factors, including the microprocessor model and the type, speed, size (capacity), and number of DIMMs installed.
Table 1.
Appendix B. Notices Lenovo may not offer the products, services, or features discussed in this document in all countries. Consult your local Lenovo representative for information on the products and services currently available in your area. Any reference to a Lenovo product, program, or service is not intended to state or imply that only that Lenovo product, program, or service may be used.
vary significantly. Some measurements may have been made on development-level systems and there is no guarantee that these measurements will be the same on generally available systems. Furthermore, some measurements may have been estimated through extrapolation. Actual results may vary. Users of this document should verify the applicable data for their specific environment. Television output notice The following notice applies to models that have the factory-installed television-output feature.
Index A front fan assembly, replacing a rescue medium, creating and using Administrator password 54 advanced settings 56 antivirus software 5 audio line-in connector 8 audio line-out connector 8 audio subsystem 2 49 G getting help 71 information service 71 heat sink and fan assembly, replacing help and service 72 getting 71 47 C IEEE 1394 connector 8 important safety information v information getting 71 important safety v resources 71 safety 72 warranty 72 Input/Output (I/O) features 2 installing de
N notice, television output notices 77 78 O Online Books folder 71 operations, backup and recovery optical mouse cleaning 69 Optical SPDIF in connector 9 Optical SPDIF out connector 9 47 P parts replacement, completing 40 password Administrator password 54 considerations 54 setting, changing, deleting 54 user 54 password protection 43 PC-Doctor for Rescue and Recovery PCI card 22 installing, replacing 22 slots 22 physical specifications 4 power supply features 3 power-on self-test (POST) 63 programs, up
W warranty information 72 Web site, Lenovo 72 workspace, backup and recovery 48 Index 81
82 User Guide
Part Number: 89Y7306 Printed in USA (1P) P/N: 89Y7306