User Guide Types 8011, 8793, 8797, 8801 Types 8805, 8810, 8814
User Guide Types 8011, 8793, 8797, 8801 Types 8805, 8810, 8814
Note Before using this information and the product it supports, be sure to read the “Important safety information” on page v and Appendix B, “Notices,” on page 73. First Edition (May 2006) © Copyright Lenovo 2005, 2006. Portions © Copyright International Business Machines Corporation 2005. All rights reserved. U.S. GOVERNMENT USERS – RESTRICTED RIGHTS: Our products and/or services are provided with RESTRICTED RIGHTS.
Contents Important safety information . . . . . . v Conditions that require immediate action . . . . . v General safety guidelines . . . . . . . . . . vi Service . . . . . . . . . . . . . . . vi Power cords and power adapters . . . . . . vii Extension cords and related devices . . . . . viii Plugs and outlets . . . . . . . . . . . viii Batteries . . . . . . . . . . . . . . viii Heat and product ventilation . . . . . . . ix CD and DVD drive safety . . . . . . . . . ix Additional safety information. . . . . .
ThinkVantage Productivity Center . . . Access Help . . . . . . . . . . Warranty and safety . . . . . . . www.lenovo.com . . . . . . . . Help and service . . . . . . . . . Using the documentation and diagnostic programs . . . . . . . . . . . Calling for service . . . . . . . . Using other services . . . . . . . Purchasing additional services . . . . . . . . . . . . . . . . . . . 61 62 62 62 62 . . . . . . . . . . . . 63 63 64 64 Appendix B. Notices . . . . . . . . . 73 Appendix A.
Important safety information Note Please read the following important safety information first. This information can help you safely use your desktop or notebook personal computer. Follow and retain all information included with your computer. The information in this document does not alter the terms of your purchase agreement or the Lenovo™ Statement of Limited Warranty. For more information, refer to the warranty and safety information that is provided with your computer. Customer safety is important.
In the unlikely event that you notice any of the following conditions, or if you have any safety concerns with your product, stop using the product and unplug it from the power source and telecommunication lines until you can speak to the Customer Support Center for further guidance. v Power cords, plugs, power adapters, extension cords, surge protectors, or power supplies that are cracked, broken, or damaged. v Signs of overheating, smoke, sparks, or fire.
Danger Hazardous moving parts. Keep fingers and other body parts away. Attention Before replacing any CRUs, turn off the computer and wait three to five minutes to let the computer cool before opening the cover. Power cords and power adapters Use only the power cords and power adapters supplied by the product manufacturer. The power cords shall be safety approved. For Germany, it shall be H05VV-F, 3G, 0.75 mm2, or better. For other countries, the suitable types shall be used accordingly.
Extension cords and related devices Ensure that extension cords, surge protectors, uninterruptible power supplies, and power strips that you use are rated to handle the electrical requirements of the product. Never overload these devices. If power strips are used, the load should not exceed the power strip input rating. Consult an electrician for more information if you have questions about power loads, power requirements, and input ratings.
shorten the life of the battery and can also pose a safety hazard. Do not let rechargeable Lithium-Ion batteries completely discharge or store these batteries in a discharged state. Heat and product ventilation Computers generate heat when turned on and when batteries are charging. Notebook computers can generate a significant amount of heat due to their compact size.
v Remove CD and DVD discs from the computer when not in use. v Do not bend or flex CD and DVD discs, or force them into the computer or their packaging. v Check CD and DVD discs for cracks before each use. Do not use cracked or damaged discs. Additional safety information Danger Electrical current from power, telephone, and communication cables is hazardous.
Dispose of the battery as required by local ordinances or regulations. Modem safety information Caution To reduce the risk of fire, use only No. 26 AWG or larger telecommunication line cord. To reduce the risk of fire, electrical shock, or injury when using telephone equipment, always follow basic safety precautions, such as: v Never install telephone wiring during a lightning storm. v Never install telephone jacks in wet locations unless the jack is specifically designed for wet locations.
Power supply statement Never remove the cover on a power supply or any part that has the following label attached. Hazardous voltage, current, and energy levels are present inside any component that has this label attached. There are no serviceable parts inside these components. If you suspect a problem with one of these parts, contact a service technician.
Introduction This User Guide contains the following information: v Chapter 1, “Arranging your workspace,” on page 1 provides information about setting up your computer for comfort and the impact of light sources, air circulation, and electrical outlets. v Chapter 2, “Setting up your computer,” on page 3 provides information about setting up your computer and software and operating system installation.
xiv User Guide
Chapter 1. Arranging your workspace To get the most from your computer, arrange both the equipment you use and your work area to suit your needs and the kind of work you do. Your comfort is of foremost importance, but light sources, air circulation, and the location of electrical outlets also can affect the way you arrange your workspace. Comfort Although no single working position is ideal for everyone, here are a few guidelines to help you find a position that suits you best.
Where it is impossible to avoid reflections or to adjust the lighting, an antiglare filter placed over the screen might be helpful. However, these filters might affect the clarity of the image on the screen; try them only after you have exhausted other methods of reducing glare. Dust buildup compounds problems associated with glare. Remember to clean your monitor screen periodically using a soft cloth moistened with a nonabrasive liquid glass cleaner. Air circulation Your computer and monitor produce heat.
Chapter 2. Setting up your computer Before you begin, make sure you set up your computer in the best possible work area that suits your needs and the kind of work you do. For more information, refer to Chapter 1, “Arranging your workspace,” on page 1. Note: Read “Important safety information” on page v before you set up your computer. The precautions and guidelines will help you work safely. Connecting your computer Use the following information when connecting your computer.
Note: Some models will have keyboards with a fingerprint reader. After you setup and turn on your computer, refer to the Access Help online help system for information about your fingerprint reader. See “Access Help” on page 62 for instructions on how to open the online help system. 3. Connect the USB mouse cable to a USB connector. 4. Connect the monitor cable to the monitor connector on the computer. v If you have a Video Graphics Array (VGA) Standard monitor, connect the cable to the connector as shown.
5. If you have a modem, connect the modem using the following information. E ON PH E ON PH E ON PH LINE PH E LIN ON LIN 1 2 3 E E LIN E This illustration shows the two connections on the back of the computer that are needed to set up your modem. In the United States and other countries or regions that use the RJ-11 telephone outlet, attach one end of the telephone cable to the telephone and the other end to the telephone connector on the back of the computer.
7. If you have powered speakers with an ac adapter, use the following instructions. a. Connect the cable that runs between the speakers, if necessary. On some speakers, this cable is permanently attached. b. Connect the ac adapter cable to the speaker. c. Connect the speakers to the computer. d. Connect the ac adapter to the ac power source. 8. If you have unpowered speakers with no ac adapter, use the following instructions. a. Connect the cable that runs between the speakers, if necessary.
1 USB 2 Serial 3 S-video 4 Parallel 5 Ethernet 6 MIDI/joystick 7 IEEE 1394 Use this connector to attach a device that requires a USB connection, such as a keyboard, mouse, scanner, printer, or personal digital assistant (PDA). Use this connector to attach an external modem, serial printer, or other device that uses a 9-pin serial connector. Use this connector to attach a television set that has an S-Video connector. This connector is present on some high-performance video adapters.
Turning on power Turn on the monitor and other external devices first, and then turn on the computer. When the power-on self-test (POST) is finished, the logo window closes. If your computer has preinstalled software, the software installation program starts. If you experience any problems during startup, see Chapter 7, “Troubleshooting and diagnostics,” on page 55. For additional help, refer to Chapter 8, “Getting information, help, and service,” on page 61.
Updating your operating system Microsoft makes updates available for various operating systems through the Microsoft Windows Update Web site. The Web site automatically determines what Windows updates are available for your specific computer and lists those updates only. Updates could include security fixes, new versions of Windows components (such as media player), fixes to other portions of the Windows operating system, or enhancements.
10 User Guide
Chapter 3. Installing options This chapter provides an introduction to the features and options that are available for your computer. You can expand the capabilities of your computer by adding memory, adapters, or drives. When installing an option, use these instructions along with the instructions that come with the option. Important Before you install or remove any option, read “Important safety information” on page v“Important safety information” on page v.
Internal drives v 3.5-inch, half-inch (slim) diskette drive (some models) v Serial Advanced Technology Attachment (SATA) internal hard disk drive v SATA optical drive (some models) Video subsystem v An integrated graphics controller for a Video Graphics Array (VGA) monitor v Intel Graphics Media Accelerator 3000 with dual display support v PCI Express (x16) graphics adapter connector on the system board Audio subsystem The integrated HD audio controller provides four audio connectors.
Power v 225 Watt power supply with manual voltage selection switch v Automatic 50/60 Hz input frequency switching v Advanced Power Management support v Advanced Configuration and Power Interface (ACPI) support Security features v User and administrator passwords for BIOS access v Support for the addition of a rope clip (U-bolt) v Support for the addition of an integrated cable lock (Kensington lock) to secure the cover v Keyboard with fingerprint reader (some models, see the ThinkVantage Productivity Center
Available options The following are some available options: v External options – Parallel port devices, such as printers and external drives – Serial port devices, such as external modems and digital cameras – Audio devices, such as external speakers for the sound system – USB devices, such as printers, joysticks, and scanners – Security devices, such as a rope clip and an integrated cable lock – Monitors v Internal options – System memory, called dual inline memory modules (DIMMs) – Peripheral component in
Specifications This section lists the physical specifications for your computer. Dimensions Width: 350 mm (13.8 in.) Height: 107.9 mm (4.2 in.) Depth: 385 mm (15.2 in.) Weight Minimum configuration as shipped: 8.4 kg (18.5 lbs) Maximum configuration: 10.0 kg (22.0 lbs) Environment Air temperature: Operating at 0 - 3000 ft (914.4 m): 10° to 35°C (50° to 95°F) Operating at 3000 ft - 7000 ft (2134 m): 10° to 32°C (50° to 89.
Supported operating positions To provide proper air flow to internal components, you must position your computer in one of the positions as illustrated below. Note: In the vertical position, the speaker vents should face up to ensure optimal sound.
Tools required To install some options in your computer, you might need a flat-blade or Phillips screwdriver. Additional tools might be needed for certain options. See the instructions that come with the option. Handling static-sensitive devices Static electricity, although harmless to you, can seriously damage computer components and options. When you add an option, do not open the static-protective package containing the option until you are instructed to do so.
Installing external options This section shows the various external connectors on your computer to which you can attach external options, such as external speakers, a printer, or a scanner. For some external options, you must install additional software in addition to making the physical connection.
Locating connectors on the rear of your computer The following illustration shows locations of connectors on the rear of your computer.
Connector Description Audio line in connector Used to receive audio signals from an external audio device, such as a stereo system. When you attach an external audio device, a cable is connected between the audio line out connector of the device and the audio line in connector of the computer.
Opening the cover Important Read “Important safety information” on page v“Important safety information” on page v and “Handling static-sensitive devices” on page 17 before opening the computer cover. To open the computer cover: 1. Remove any media (diskettes, CDs, or tapes) from the drives, shut down your operating system, and turn off all attached devices and computer. 2. Unplug all power cords from electrical outlets. 3. Disconnect all cables attached to the computer.
Locating components The following illustration will help you locate the various components in your computer.
Identifying parts on the system board The system board (sometimes called the planar or motherboard) is the main circuit board in your computer. It provides basic computer functions and supports a variety of devices that are installed or that you can install later. The following illustration shows the locations of parts on the system board.
Installing memory Your computer has four connectors for installing double date rate dual inline memory modules (DDR2 DIMMs) that provide up to a maximum of 4.0 GB of system memory. When installing memory modules, the following rules apply: v Use 1.8 V, 240-pin, double data rate 2 synchronous dynamic random access memory (DDR2 SDRAM). v Use 256 MB, 512 MB, 1.0 GB, or 2.0 GB DIMMs in any combination (up to 8.0GB). Note: Only DDR2 SDRAM DIMMs can be used. To install a memory module: 1. Open the computer cover.
4. Open the retaining clips. 5. Position the memory module over the memory connector. Make sure that the notch 1 on the memory module aligns correctly with the connector key 2 on the system board. Push the memory module straight down into the connector until the retaining clips close. What to do next: v To work with another option, go to the appropriate section. v To complete the installation, go to “Closing the cover and connecting the cables” on page 39.
2. While holding the left rear of the computer chassis down, pull upward on the handle provided to remove the PCI riser and any adapters that are currently installed. 3. Release the adapter latch and remove the connector cover for the appropriate expansion connector. 4. Remove the adapter from its static-protective package.
5. Install the adapter into the appropriate connector in the PCI riser. 6. Position the adapter latch to retain the adapters. 7. Reinstall the PCI riser assembly. What to do next: v To work with another option, go to the appropriate section. v To complete the installation, go to “Closing the cover and connecting the cables” on page 39. Installing internal drives This section provides information and instructions for installing and removing internal drives.
Drive specifications Your computer comes with the following installed drives: v An optical drive in bay 1 (some models) v A 3.5-inch diskette drive in bay 2 (some models) v A 3.5-inch hard disk drive in bay 3 Any bay that does not have a drive installed has a static shield and bay panel installed. The following illustration shows the locations of the drive bays. The following list describes the types and size of drives you can install in each bay: 1 Bay 1 - Maximum height: 42.0 mm (1.65 in.
Installing a drive in bay 1 To install an optical drive or an additional hard disk drive in bay 1, do the following: 1. Open the computer cover. See “Opening the cover” on page 21. 2. Remove the plastic panel from the front bezel. 3. Remove the metal shield from the drive bay by using a flat-blade screwdriver to gently pry it loose. 4. For a 5.25-inch drive, install a retainer bracket on the side of the drive. 5. For a 3.5-inch drive, install the drive into the Universal Adapter Bracket, 5.25 to 3.5-inch.
6. Install the drive into the bay until it snaps into position. 7. Continue at “Connecting drives.” Connecting drives The steps to connect a drive are different depending on the type of drive you are connecting. Use the following procedures for your drive connection.
Connecting additional serial ATA hard disk drive A serial hard disk drive can be connected to any available SATA connector. 1. Locate the signal cable that comes with the new drive. 2. Locate the available SATA connector on the system board. See “Identifying parts on the system board” on page 23. 3. Connect one end of the signal cable to the drive and the other to the available SATA connector on the system board. 4. Locate one of the extra five-wire power connectors and connect it to the drive.
Installing a diskette drive in bay 2 To install a diskette drive in bay 2, do the following: 1. Open the computer cover. See “Opening the cover” on page 21. 2. Pivot the drive bay assembly upward. 3. Remove the plastic panel from the front bezel. 4. Remove the metal shield from the drive bay by using a flat-blade screwdriver to gently pry it loose. 5. Connect the flat cable to the new drive. 6. Install a retainer bracket on the side of the drive.
7. Install the new drive from the rear of the drive bay assembly. What to do next: v To work with another option, go to the appropriate section. v To complete the installation, go to “Closing the cover and connecting the cables” on page 39. Chapter 3.
Security features To help prevent hardware theft and unauthorized access to your computer, several security lock options are available. The following sections will help you identify and install the various types of locks that might be available for your computer. In addition to a physical lock, unauthorized use of your computer can be prevented by a software lock that locks the keyboard until a correct password is typed in.
Rope Clip Using a 3/16-inch or 5-mm rope clip (sometimes referred to as a U-bolt), a steel security cable, and a padlock can secure your computer to a desk, table, or other non-permanent fixture. Rope clip knockouts at the rear of the chassis are provided. To 1. 2. 3. install a rope clip: Open the computer cover. See “Opening the cover” on page 21. Use a tool, such as a screwdriver, to remove the two metal knockouts.
Integrated cable lock With an integrated cable lock (sometimes referred to as the Kensington lock), you can secure your computer to a desk, table, or other non-permanent fixture. The cable lock attaches to a security slot at the rear of your computer and is operated with a key. The cable lock also locks the buttons used to open the computer cover. This is the same type of lock used with many laptop computers. You can order a security cable directly from http://www.lenovo.
Changing the battery Your computer has a special type of memory that maintains the date, time, and settings for built-in features, such as parallel-port assignments (configuration). A battery keeps this information active when you turn off the computer. The battery normally requires no charging or maintenance throughout its life; however, no battery lasts forever. If the battery fails, the date, time, and configuration information (including passwords) are lost.
5. Install the new battery. 6. Reinstall the PCI riser assembly if removed. 7. Close the computer cover, and connect the cables. See “Closing the cover and connecting the cables” on page 39. Note: When the computer is turned on for the first time after battery replacement, an error message might be displayed. This is normal after replacing the battery. 8. Turn on the computer and all attached devices. 9. Use the Setup Utility program to set the date and time and any passwords.
Closing the cover and connecting the cables After working with options, you need to install any removed parts, close the computer cover, and reconnect cables, including telephone lines and power cords. Also, depending on the option that is installed, you might need to confirm the updated information in the Setup Utility program. To close the computer cover and connect cables to your computer: 1.
40 User Guide
Chapter 4. Recovering software The Rescue and Recovery program is software aimed at helping users restore their computer data and recover from software or hardware-related failures. In the event of a computer failure, use the Rescue and Recovery program to restore the contents of the primary hard drive to a previously saved state. This chapter will help you become familiar with recovery solutions provided by Lenovo.
To use Product Recovery discs, do the following: Attention: When you restore the factory contents from the Product Recovery discs, all files currently on the hard disk will be deleted and replaced by the original factory contents. During the restore process, you will be given the opportunity to save one or more files currently on your hard disk drive to other media before any data is removed. 1. Insert the Rescue and Recovery disc into your CD or DVD drive. 2. Restart your computer. 3.
2. From the Rescue and Recovery main window, click the Restore your system from a backup icon. 3. Follow the instructions on the screen. For information about performing a restore operation from the Rescue and Recovery workspace, see “Using the Rescue and Recovery workspace.” Using the Rescue and Recovery workspace The Rescue and Recovery workspace resides in a protected, hidden area of your hard disk that operates independently from the Windows operating system.
v To rescue files from your hard disk or from a backup, click Rescue files in the Rescue and Recovery menu; then, follow the instructions on the screen. v To restore your hard disk from a Rescue and Recovery backup or to restore your hard drive to the factory contents, click Restore your system in the Rescue and Recovery menu; then, follow the instructions on the screen. Note: After restoring your hard disk to the original factory content, you might have to reinstall some software or drivers.
To create rescue media, do the following: 1. From the Windows desktop, click Start, click All Programs, click ThinkVantage, then click Create Recovery Media. 2. In the Rescue Media area, select the type of rescue media you want to create. You can create rescue media using a CD, USB hard drive, or an internal hard drive. 3. Click OK. 4. Follow the instructions on the screen. To use rescue media, do one of the following: v Insert the rescue disc and restart your computer.
and Recovery workspace. For information about creating and using rescue media, see “Creating and using rescue media” on page 44. Recovering or installing device drivers Before you can recover or install device drivers, your operating system must be installed on your computer. Make sure that you have the documentation and software media for the device. Device drivers for factory-installed devices are located on the computer hard disk (usually drive C) in the SWTOOLS\drivers folder.
7. Use the down-arrow key to select Save and exit the Setup Utility, then press Enter. 8. When the Setup Confirmation window appears, press Enter. 9. The computer restarts. Note: If you are using an external device, you first must turn off your computer before connecting the external device. For more information on Setup Utility, see Chapter 5, “Using the Setup Utility,” on page 49. Chapter 4.
48 User Guide
Chapter 5. Using the Setup Utility The Setup Utility program is stored in the electrically erasable programmable read-only memory (EEPROM) of your computer. The Setup Utility program is used to view and change the configuration settings of your computer, regardless of which operating system you are using. However, the operating-system settings might override any similar settings in the Setup Utility program. Starting the Setup Utility program To start the Setup Utility program, do the following: 1.
v v v v Setup Utility program and hard disk drive passwords are not case sensitive Not be your name or your user name Not be a common word or a common name Be significantly different from your previous password User Password When a User Password is set, the user is prompted to type a valid password each time the computer is turned on. The computer cannot be used until a valid password is typed from the keyboard.
Note: Selecting a startup device from the Startup Device menu does not permanently change the startup sequence. Changing the startup device sequence To view or permanently change the configured startup device sequence, do the following: 1. Start the Setup Utility program (see “Starting the Setup Utility program” on page 49). 2. Select Startup. 3. Select Startup Sequence. See the information displayed on the right side of the screen. 4.
52 User Guide
Chapter 6. Updating system programs This chapter contains information about updating POST/BIOS and how to recover from a POST/BIOS update failure. Using system programs System programs are the basic layer of software that is built into your computer. They include the power-on self-test (POST), the basic input/output system (BIOS) code, and the Setup Utility program. POST is a set of tests and procedures that is performed each time you turn on your computer.
54 User Guide
Chapter 7. Troubleshooting and diagnostics This chapter describes some basic troubleshooting and diagnostic programs. If your computer problem is not described here, see Chapter 8, “Getting information, help, and service,” on page 61 for additional troubleshooting resources. Basic troubleshooting The following table provides information to help you troubleshoot your computer problem. Symptom Action The computer does not start when you press the power button.
Symptom Action The Enhanced Performance USB Keyboard does not work. Verify that: v The computer is turned on. v The keyboard is securely connected to a USB connector on the front or rear of the computer. v No keys are stuck. If you cannot correct the problem, have the computer serviced. Refer to the warranty and safety information that is provided with your computer for a list of service and support telephone numbers. The mouse does not work. The computer does not respond to the mouse.
PC-Doctor for Windows PC-Doctor for Windows is a diagnostic program that works through the Windows operating system. The PC-Doctor for Windows diagnostic program enables you to view symptoms and solutions for computer problems, access the Lenovo troubleshooting center, update system drivers, and review system information. To open PC-Doctor for Windows, click Start from the Windows desktop, select All Programs, select PC-Doctor for Windows, and click PC-Doctor for Windows.
6. Follow the instructions on the screen. 7. When prompted, insert a blank, formatted diskette into the diskette drive and continue to follow the instructions on the screen. 8. When the operation is complete, remove the diskette and click Quit. 9. Insert another blank, formatted diskette into the diskette drive and continue to follow the instructions on the screen. 10. When the operation is complete, remove the diskette and click Quit.
Optical mouse An optical mouse uses a light-emitting diode (LED) and an optical sensor to navigate the pointer. If the pointer on the screen does not move smoothly with the optical mouse, you might need to clean the mouse. Use the following procedure to clean the optical mouse: 1. Turn off your computer. 2. Disconnect the mouse cable from the computer. 3. Turn the mouse upside down to look at the lens. a. If there is a smudge on the lens, gently clean the area with a plain cotton-tipped swab. b.
To clean a mouse with a ball, follow the instructions below: 1. Turn off your computer. 2. Disconnect the mouse cable from the computer. 3. Turn the mouse upside down. Twist the retainer ring 1 to the unlocked position to remove the ball. 4. Place your hand over the retainer ring and ball 2 , and then turn the mouse right-side up, so that the retainer ring and ball fall out into your hand. 5. Wash the ball in warm, soapy water then dry it with a clean cloth. 6.
Chapter 8. Getting information, help, and service If you need help, service, or technical assistance or just want more information about products manufactured by Lenovo, you will find a wide variety of sources available from Lenovo to assist you. Information resources This section provides information on how to access useful resources relating to your computing needs. Online Books folder The Online Books folder provides publications to help you set up and use your computer.
v v v v Client Security Solutions Factory Recovery System Updates Service and support Note: ThinkVantage Technologies are only available on select Lenovo computers. To access the ThinkVantage Productivity Center program, click Start, select All Programs, select ThinkVantage, and click Productivity Center.
Using the documentation and diagnostic programs Many computer problems can be solved without outside assistance. If you experience a problem with your computer, see Chapter 7, “Troubleshooting and diagnostics,” on page 55. For information on additional resources to help you troubleshoot your computer problem, see “Information resources” on page 61. If you suspect a software problem, see the documentation, including README files and online help, that comes with the operating system or application program.
Note: Phone numbers are subject to change without notice. If the number for your country or region is not provided, contact your Lenovo reseller or Lenovo marketing representative.
Appendix A. Manual modem commands This appendix provides commands for manually programming your modem. Commands are accepted by the modem while it is in Command Mode. Your modem is automatically in Command Mode until you dial a number and establish a connection. Commands can be sent to your modem from a PC running communication software or any other terminal devices. All commands sent to the modem must begin with AT and end with ENTER. All commands can be typed in either upper or lower case, but not mixed.
Command Function H1 Force modem off-hook (make busy) Note: H1 command is not supported for Italy I_ L_ M_ I0 Display product-identification code I1 Factory ROM checksum test I2 Internal memory test I3 Firmware ID I4 Reserved ID L0 Low speaker volume L1 Low speaker volume L2 Medium speaker volume L3 High speaker volume M0 Internal speaker off M1 Internal speaker on until carrier detected M2 Internal speaker always on M3 Internal speaker on until carrier detected and off while d
Extended AT commands Command Function &C0 Force Carrier Detect Signal High (ON) &C1 Turn on CD when remote carrier is present &D0 Modem ignores the DTR signal &D1 Modem returns to Command Mode after DTR toggle &D2 Modem hangs up, returns to the Command Mode after DTR toggle &D3 Resets modem after DTR toggle &F_ &F Recall factory default configuration &G_ &G0 Guard tone disabled &G1 Guard tone disabled &G2 1800 Hz guard tone &K0 Disable flow control &K3 Enable RTS/CTS hardware flow
Command Function &W_ %E_ &V1 Display Last Connection Statistics &W0 Stores the active profile as Profile 0 &W1 Stores the active profile as Profile 1 %E0 Disable auto-retrain %E1 Enable auto-retrain +MS? Displays the current Select Modulation settings +MS=? Displays a list of supported Select Modulation options +MS=a,b,c,e,f Select modulation where: a=0, 1, 2, 3, 9, 10, 11, 12, 56, 64, 69; b=0-1; c=300-56000; d=30056000; e=0-1; and f=0-1. A, b, c, d, e, f default=12, 1, 300, 56000, 0, 0.
Fax Class 1 commands +FAE=n Data/Fax Auto Answer +FCLASS=n Service Class +FRH=n Receive data with HDLC framing +FRM=n Receive data +FRS=n Receive silence +FTH=n Transmit data with HDLC framing +FTM=n Transmit data +FTS=n Stop transmission and wait Fax Class 2 commands +FCLASS=n Services class. +FAA=n Adaptive answer. +FAXERR Fax error value. +FBOR Phase C data bit order. +FBUF? Buffer size (read only). +FCFR Indicate confirmation to receive. +FCLASS= Service class.
+FPHCTO Phase C time out. +FPOLL Indicates polling request. +FPTS: Page transfer status. +FPTS= Page transfer status. +FREV? Identify revision. +FSPT Enable polling. +FTSI: Report the transmit station ID.
Attention Switzerland User: If your Swisscom phone line does not have Taxsignal switched OFF, modem function may be impaired. The impairment may be resolved by a filter with the following specifications: Telekom PTT SCR-BE Taximpulssperrfilter-12kHz PTT Art. 444.112.7 Bakom 93.0291.Z.N Appendix A.
72 User Guide
Appendix B. Notices Lenovo may not offer the products, services, or features discussed in this document in all countries. Consult your local Lenovo representative for information on the products and services currently available in your area. Any reference to a Lenovo product, program, or service is not intended to state or imply that only that Lenovo product, program, or service may be used.
vary significantly. Some measurements may have been made on development-level systems and there is no guarantee that these measurements will be the same on generally available systems. Furthermore, some measurements may have been estimated through extrapolation. Actual results may vary. Users of this document should verify the applicable data for their specific environment. Television output notice The following notice applies to models that have the factory-installed television-output feature.
Index A Access Help 62 adapter connectors 25 installing 25 peripheral component interconnect (PCI) antivirus software, updating 9 arranging your workspace 1 audio line in connector 20 audio line out connector 20 audio subsystem 12 drives bays 28 internal 27 specifications 28 dual inline memory modules (DIMMs) 14 B battery, changing 37 BIOS, updating (flashing) 24 53 E environment, operating 15 Ethernet 12 Ethernet connector 20 exiting, Setup Utility 51 expansion adapters 12 external options 18 F featu
N non-optical mouse notices 73 software installing 8 recovering 41 specifications 15 startup sequence, rescue device system board connectors 23 identifying parts 23 location 23 memory 14, 24 system management 12 system programs 53 59 O Online Books folder 61 opening the cover 21 operating system installing 9 updating 9 optical mouse 59 options 14 available 14 external 14 internal 14 T ThinkVantage Productivity Center trademarks 74 troubleshooting 55 P parallel connector 20 password administrator 50 era
Part Number: 41X6154 Printed in USA (1P) P/N: 41X6154
