ThinkPad T400s, T410s, and T410si Hardware Maintenance Manual
ThinkPad T400s, T410s, and T410si Hardware Maintenance Manual
Note Before using this information and the product it supports, be sure to read the general information under “Notices” on page 205. Third Edition (January 2010) © Copyright Lenovo 2009, 2010. LENOVO products, data, computer software, and services have been developed exclusively at private expense and are sold to governmental entities as commercial items as defined by 48 C.F.R. 2.101 with limited and restricted rights to use, reproduction and disclosure.
Contents About this manual . . . . . . . . . . v Safety information . . . . . . . . . . 1 General safety . . . . . . . . . . . . . . 2 Electrical safety . . . . . . . . . . . . . 3 Safety inspection guide . . . . . . . . . . . 5 Handling devices that are sensitive to electrostatic discharge . . . . . . . . . . . . . . . 6 Grounding requirements . . . . . . . . . . 6 Safety notices (multilingual translations) . . . . . 7 Laser compliance statement (multilingual translations) . . . . . . . . . . . . . .
Parts list . . . . . . . . . . . . . 151 Overall . . . . . . . . . . . . . . LCD FRUs . . . . . . . . . . . . . Keyboard. . . . . . . . . . . . . . Miscellaneous parts . . . . . . . . . . AC adapters. . . . . . . . . . . . . Power cords . . . . . . . . . . . . . Recovery discs . . . . . . . . . . . . Windows XP Professional (32 bit) DVDs . . Windows Vista Starter Edition (32 bit) DVDs Windows Vista Home Basic (32 bit) DVDs . . Windows Vista Home Premium (32 bit) DVDs Windows Vista Business (32 bit) DVDs . .
About this manual This manual contains service and reference information for the following ThinkPad® products. ThinkPad T400s MT 2801, 2808, 2809, 2815, 2823, 2824, and 2825 ThinkPad T410s and T410si MT 2901, 2904, 2907, 2912, and 2924 Use this manual along with the advanced diagnostic tests to troubleshoot problems. Important: This manual is intended only for trained service technicians who are familiar with ThinkPad products.
vi ThinkPad T400s, T410s, and T410si Hardware Maintenance Manual
Safety information This chapter presents following safety information that you need to be familiar with before you service a ThinkPad Notebook.
General safety Follow these rules to ensure general safety: v Observe good housekeeping in the area of the machines during and after maintenance. v When lifting any heavy object: 1. Make sure that you can stand safely without slipping. 2. Distribute the weight of the object equally between your feet. 3. Use a slow lifting force. Never move suddenly or twist when you attempt to lift. 4. Lift by standing or by pushing up with your leg muscles; this action removes the strain from the muscles in your back.
Electrical safety Observe the following rules when working on electrical equipment. Important: Use only approved tools and test equipment. Some hand tools have handles covered with a soft material that does not insulate you when working with live electrical currents. Many customers have, near their equipment, rubber floor mats that contain small conductive fibers to decrease electrostatic discharges. Do not use this type of mat to protect yourself from electrical shock.
v Do not touch live electrical circuits with the reflective surface of a plastic dental mirror. The surface is conductive; such touching can cause personal injury and machine damage. v Do not service the following parts with the power on when they are removed from their normal operating places in a machine: – Power supply units – Pumps – Blowers and fans – Motor generators – Similar units to listed above This practice ensures correct grounding of the units.
Safety inspection guide The purpose of this inspection guide is to assist you in identifying potentially unsafe conditions. As each machine was designed and built, required safety items were installed to protect users and service technicians from injury. This guide addresses only those items. You should use good judgment to identify potential safety hazards due to attachment of non-ThinkPad features or options not covered by this inspection guide.
Handling devices that are sensitive to electrostatic discharge Any computer part containing transistors or integrated circuits (ICs) should be considered sensitive to electrostatic discharge (ESD.) ESD damage can occur when there is a difference in charge between objects. Protect against ESD damage by equalizing the charge so that the machine, the part, the work mat, and the person handling the part are all at the same charge. Notes: 1.
Safety notices (multilingual translations) The safety notices in this section are provided in the following languages: v English v Arabic v Brazilian Portuguese v French v German v Hebrew v Japanese v Korean v Spanish v Traditional Chinese Safety information 7
DANGER Before the computer is powered on after FRU replacement, make sure all screws, springs, and other small parts are in place and are not left loose inside the computer. Verify this by shaking the computer and listening for rattling sounds. Metallic parts or metal flakes can cause electrical shorts. DANGER Some standby batteries contain a small amount of nickel and cadmium. Do not disassemble a standby battery, recharge it, throw it into fire or water, or short-circuit it.
DANGER To avoid shock, do not remove the plastic cover that protects the lower part of the inverter card. DANGER Though the main batteries have low voltage, a shorted or grounded battery can produce enough current to burn personnel or combustible materials. DANGER Unless hot swap is allowed for the FRU being replaced, do as follows before removing it: power off the computer, unplug all power cords from electrical outlets, remove the battery pack, and disconnect any interconnecting cables.
10 ThinkPad T400s, T410s, and T410si Hardware Maintenance Manual
Safety information 11
PERIGO Antes de ligar o computador após a substituição da FRU, certifique-se de que todos os parafusos, molas e outras peças pequenas estejam no lugar e não estejam soltos dentro do computador. Verifique isso sacudindo o computador e procurando ouvir sons de peças soltas. Peças metálicas ou lascas de metal podem causar curto-circuito. PERIGO Algumas baterias reserva contêm uma pequena quantidade de níquel e cádmio.
PERIGO Para evitar choque elétrico, não remova a capa plástica que protege a parte inferior da placa inversora. PERIGO Embora as principais baterias possuam baixa voltagem, uma bateria em curto-circuito ou aterrada pode produzir corrente o bastante para queimar materiais de pessoal ou inflamáveis.
DANGER Avant de remettre l’ordinateur sous tension après remplacement d’une unité en clientèle, vérifiez que tous les ressorts, vis et autres pièces sont bien en place et bien fixées. Pour ce faire, secouez l’unité et assurez-vous qu’aucun bruit suspect ne se produit. Des pièces métalliques ou des copeaux de métal pourraient causer un court-circuit. DANGER Certaines batteries de secours contiennent du nickel et du cadmium. Ne les démontez pas, ne les rechargez pas, ne les exposez ni au feu ni à l’eau.
DANGER Afin d’éviter tout risque de choc électrique, ne retirez pas le cache en plastique protégeant la partie inférieure de la carte d’alimentation. DANGER Bien que le voltage des batteries principales soit peu élevé, le court-circuit ou la mise à la masse d’une batterie peut produire suffisamment de courant pour brûler des matériaux combustibles ou causer des brûlures corporelles graves.
VORSICHT Bevor nach einem FRU-Austausch der Computer wieder angeschlossen wird, muß sichergestellt werden, daß keine Schrauben, Federn oder andere Kleinteile fehlen oder im Gehäuse vergessen wurden. Der Computer muß geschüttelt und auf Klappergeräusche geprüft werden. Metallteile oder-splitter können Kurzschlüsse erzeugen. VORSICHT Die Bereitschaftsbatterie, die sich unter dem Diskettenlaufwerk befindet, kann geringe Mengen Nickel und Cadmium enthalten.
VORSICHT Die Leuchtstoffröhre im LCD-Bildschirm enthält Quecksilber. Bei der Entsorgung die örtlichen Bestimmungen für Sondermüll beachten. Der LCD-Bildschirm besteht aus Glas und kann zerbrechen, wenn er unsachgemäß behandelt wird oder der Computer auf den Boden fällt.
18 ThinkPad T400s, T410s, and T410si Hardware Maintenance Manual
Safety information 19
20 ThinkPad T400s, T410s, and T410si Hardware Maintenance Manual
Safety information 21
22 ThinkPad T400s, T410s, and T410si Hardware Maintenance Manual
Safety information 23
PELIGRO Antes de encender el sistema despues de sustituir una FRU, compruebe que todos los tornillos, muelles y demás piezas pequeñas se encuentran en su sitio y no se encuentran sueltas dentro del sistema. Compruébelo agitando el sistema y escuchando los posibles ruidos que provocarían. Las piezas metálicas pueden causar cortocircuitos eléctricos. PELIGRO Algunas baterías de reserva contienen una pequeña cantidad de níquel y cadmio.
PELIGRO Para evitar descargas, no quite la cubierta de plástico que rodea la parte baja de la tarjeta invertida. PELIGRO Aunque las baterías principales tienen un voltaje bajo, una batería cortocircuitada o con contacto a tierra puede producir la corriente suficiente como para quemar material combustible o provocar quemaduras en el personal.
26 ThinkPad T400s, T410s, and T410si Hardware Maintenance Manual
Safety information 27
Laser compliance statement (multilingual translations) The laser compliance statements in this section are provided in the following languages: v English v Arabic v Brazilian Portuguese v French v German v Hebrew v Japanese v Korean v Spanish v Traditional Chinese Some models of ThinkPad Notebook are equipped from the factory with an optical storage device such as a CD-ROM drive or a DVD-ROM drive. Such devices are also sold separately as options.
Safety information 29
Alguns modelos de computador ThinkPad são equipados na fábrica com um dispositivo de armazenamento ótico, como uma unidade de CD-ROM ou de DVD-ROM. Tais dispositivos também são vendidos separadamente como opcionais. Se uma dessas unidades estiver instalada, ela é certificada nos Estados Unidos em conformidade com os requisitos do Department of Health and Human Services 21 Code of Federal Regulations (DHHS 21 CFR), Subcapítulo J, para produtos a laser da Classe 1.
Certains modèles d’ordinateur ThinkPad sont équipés d’origine d’une unité de stockage optique telle qu’une unité de CD-ROM ou de DVD-ROM. Ces unités sont également vendues séparément en tant qu’options. Si l’une de ces unités est installée, elle est certifiée conforme, aux Etats-Unis, aux normes indiquées dans le sous-chapitre J du DHHS 21 CFR relatif aux produits à laser de classe 1.
Einige ThinkPad-Modelle sind werkseitig mit einem CD-ROM- oder DVD-ROM-Laufwerk ausgestattet. CD- und DVD-Laufwerke können auch gesondert als Zusatzeinrichtung erworben werden. Die Laufwerke erfüllen die Anforderungen gemäß IEC 60825-1 (International Electrotechnical Commission) und gemäß CENELEC EN 60825-1 für Laserprodukte der Klasse 1.
Safety information 33
34 ThinkPad T400s, T410s, and T410si Hardware Maintenance Manual
Safety information 35
Algunos modelos de sistemas ThinkPad están equipados de fábrica con un dispositivo de almacenamiento óptico, como una unidad de CD-ROM o de DVD-ROM. Estas unidades también se venden por separado como opciones. Si está instalada alguna de dichas unidades, se certifica que en los Estados Unidos cumple los requisitos del Department of Health and Human Services 21 Code of Federal Regulations (DHHS 21 CFR) Subchapter J para productos láser de Clase 1.
Safety information 37
38 ThinkPad T400s, T410s, and T410si Hardware Maintenance Manual
Important service information This chapter presents following important service information that applies to all machine types supported by this manual: v “Strategy for replacing FRUs” – “Strategy for replacing a hard disk drive” on page 40 – “Important notice for replacing a system board” on page 40 – “How to use error message” on page 40 v “Strategy for replacing FRUs for CTO, CMV, and GAV” on page 41 – “Product definition” on page 41 – “FRU identification for CTO, CMV, and GAV products” on page 41 Import
Use the following strategy to prevent unnecessary expense for replacing and servicing FRUs: v If you are instructed to replace a FRU but the replacement does not correct the problem, reinstall the original FRU before you continue. v Some computers have both a processor board and a system board. If you are instructed to replace either the processor board or the system board, and replacing one of them does not correct the problem, reinstall that board, and then replace the other one.
Strategy for replacing FRUs for CTO, CMV, and GAV Product definition Dynamic Configure To Order (CTO) This provides the ability for a customer to configure an IBM® or a Lenovo solution from an eSite, and have this configuration sent to fulfillment, where it is built and shipped directly to the customer. The machine label, Product Entitlement Warehouse (PEW), eSupport, and the HMM will load these products as the 4-digit MT and 3-digit model, where model = “CTO” (Example: 1829-CTO).
v Business Partners using Eclaim will access PEW when performing Entitlement Lookup. Business Partners will enter Loc ID, MT and Serial, and the key commodities will be returned in the Eclaim record under SYSTEM DETAILS. v Authorized IBM Business Partners can access Eclaim at the following Web site: https://wca.eclaim.
General checkout This chapter presents following information: v “What to do first” on page 44 v “Checkout guide” on page 45 – “Diagnostics using PC-Doctor for DOS” on page 45 – “Lenovo ThinkVantage Toolbox (Lenovo System Toolbox)” on page 48 – “PC-Doctor for Rescue and Recovery” on page 48 – “FRU tests” on page 49 v “Power system checkout” on page 51 The descriptions in this chapter apply to any ThinkPad model that supports the PC-Doctor® for DOS diagnostics program.
What to do first When you do return a FRU, you must include the following information in the parts exchange form or parts return form that you attach to it: __ 1. Name and phone number of service technician __ 2. Date of service __ 3. Date on which the machine failed __ 4. Date of purchase __ 5. Failure symptoms, error codes appearing on the display, and beep symptoms __ 6. Procedure index and page number in which the failing FRU was detected __ 7. Failing FRU name and part number __ 8.
Checkout guide Use the following procedures as a guide in identifying and correcting problems with the ThinkPad Notebook. Note: The diagnostic tests are intended to test only ThinkPad products. The use of non-ThinkPad products, prototype cards, or modified options can lead to false indications of errors and invalid system responses. 1. Identify the failing symptoms in as much detail as possible. 2. Verify the symptoms.
Testing the computer Note: The PC-Doctor diagnostic CD does not support any optical drives connected through USB devices or any others. It supports only the internal optical drive of the ThinkPad Notebook. To run the test, do as follows: 1. Turn off the computer. 2. Make sure that the internal optical drive that is supported as a startup device is attached to the computer. 3. Turn on the computer. If the computer cannot be powered on, go to “Power system checkout” on page 51, and check the power sources.
The options on the test menu are as follows: Diagnostics v v v v v v v v v v v v Run Normal Test Run Quick Test CPU/Coprocessor System board Video Adapter Fixed Disks Diskette Drives Other Devices ThinkPad Devices Communication Wireless LAN Advanced Memory Tests Interactive Tests v v v v v v v v Keyboard Video Internal Speaker Mouse Diskette System Load Optical Drive Test Intel WLAN Radio Test Note: v In the Keyboard test in Interactive Tests, the Fn key should be held down for at least 2 seconds; other
v v v v v v Battery Rundown View Test Log Print Log Save Log Full Erase Hard Drive Quick Erase Hard Drive Lenovo ThinkVantage Toolbox (Lenovo System Toolbox) Lenovo ThinkVantage® Toolbox (Lenovo System Toolbox in Windows Vista® and Windows® XP) is a diagnostic program that works through the Windows operating system.
FRU tests The following table shows the test for each FRU. Table 1. FRU tests FRU Applicable test System board 1. Diagnostics --> CPU/Coprocessor 2. Diagnostics --> Systemboard 3. If the docking station or the port replicator is attached to the ThinkPad Notebook, detach it. 4. Place the computer on a horizontal surface, and run Diagnostics --> ThinkPad Devices --> HDD Active Protection Test. Note: Do not apply any physical shock to the computer while the test is running.
Table 1. FRU tests (continued) FRU Applicable test TrackPoint or pointing If the TrackPoint does not work, check the configuration as device specified in the BIOS Setup Utility. If the TrackPoint is disabled, select Automatic to enable it. After you use the TrackPoint, the pointer may drift on the screen for a short time. This drift can occur when a slight, steady pressure is applied to the TrackPoint pointer. This symptom is not a hardware problem.
Power system checkout To 1. 2. 3. 4. 5. 6. 7. verify a symptom, do the following: Turn off the computer. Remove the battery pack. Connect the ac adapter. Check that power is supplied when you turn on the computer. Turn off the computer. Disconnect the ac adapter and install the charged battery pack. Check that the battery pack supplies power when you turn on the computer.
Checking operational charging To check whether the battery charges properly during operation, use a discharged battery pack or a battery pack that has less than 50% of the total power remaining when installed in the computer. Perform operational charging. If the battery status indicator or icon does not turn on, remove the battery pack and let it return to room temperature. Reinstall the battery pack. If the charge indicator or icon still does not turn on, replace the battery pack.
Checking the backup battery Do the following: 1. Power off the computer, and unplug the ac adapter from it. 2. Turn the computer upside down. 3. Remove the battery pack (see “1010 Battery pack” on page 85). 4. Remove the backup battery (see “1080 Backup battery” on page 103). 5. Measure the voltage of the backup battery. See the following figure. Red (+) Black (-) Wire Voltage (V dc) Red +2.5 to +3.2 Black Ground v If the voltage is correct, replace the system board.
54 ThinkPad T400s, T410s, and T410si Hardware Maintenance Manual
Related service information This chapter presents following information: v “Restoring the factory contents by using Product Recovery discs” v “Restoring the factory contents by using Recovery Disc Set” on page 56 v “Passwords” on page 57 v “Power management” on page 60 v “Symptom-to-FRU index” on page 62 Service Web site: When the latest maintenance diskette and the system program service diskette become available, they will be posted on http://www.lenovo.
8. When the recovery process is complete, the Welcome to Microsoft Windows screen is displayed. Follow the instructions on the screen to complete the Windows setup. Restoring the factory contents by using Recovery Disc Set When the hard disk drive (HDD) or solid state drive (SSD) is replaced because of a failure, no product recovery program is on the new drive. In this case, you must use the Recovery Disc Set for the computer.
5. Read the license. If you agree with the terms and conditions, select I accept these terms and conditions and then click Next. If you do not agree with the terms and conditions, follow the instructions on the screen. 6. Click Yes in the displayed window to begin the operating system recovery process. 7. Insert the Applications and Drivers Recovery Disc when prompted and then click OK to begin the applications and drivers recovery process. 8.
Note: There are two modes for the HDP: User only and Master + User. The Master + User mode requires two HDPs; the system administrator enters both in the same operation. The system administrator then provides the user HDP to the system user. Attention: If the user HDP has been forgotten, check whether a master HDP has been set. If it has, it can be used for access to the hard disk drive.
5. Select Power-On Password. 6. Type the current SVP in the Enter Current Password field. then leave the Enter New Password field blank, and press Enter twice. 7. In the Changes have been saved window, press Enter. 8. Press F10; then, in the Setup confirmation window, select Yes.
Power management To reduce power consumption, the computer has three power management modes: screen blank, sleep (standby in Windows XP), and hibernation. Screen blank mode If the time set on the “Turn off monitor” timer in the operating system expires, the LCD backlight turns off. To put the computer into screen blank mode, do as follows: 1. Press Fn+F3. A panel for selecting a power plan (in Windows XP, power scheme) appears. 2.
Also, in either of the following events, the computer automatically returns from sleep (standby) mode and resumes operation: v The ring indicator (RI) is signaled by a serial device or a PC Card device. v The time set on the resume timer elapses. Note: The computer does not accept any input immediately after it enters sleep (standby) mode. Wait a few seconds before taking any action to reenter operation mode.
Symptom-to-FRU index This section contains following information: v “Numeric error codes” v “Error messages” on page 66 v “Beep symptoms” on page 67 v “No-beep symptoms” on page 67 v “LCD-related symptoms” on page 68 v “Intermittent problems” on page 69 v “Undetermined problems” on page 69 The symptom-to-FRU index in this section lists symptoms and errors and their possible causes. The most likely cause is listed first, in boldface type.
Table 2. Numeric error codes (continued) Symptom or error FRU or action, in sequence 0187 EAIA data access error—The access to EEPROM is failed. System board. 0188 Invalid RFID Serialization Information Area. System board. 0189 System board. Invalid RFID configuration information area—The EEPROM checksum is not correct. 0190 Critical low-battery error 1. Charge the battery pack. 2. Battery pack. 0191 System Security—Invalid Remote Change requested. 1.
Table 2. Numeric error codes (continued) 64 Symptom or error FRU or action, in sequence 0251 System CMOS checksum bad— Default configuration used. 1. Charge the backup battery for more than 8 hours by connecting the ac adapter. 2. Replace the backup battery and run BIOS Setup Utility to reset the time and date. 0252 Password checksum bad—The password is cleared. Reset the password by running BIOS Setup Utility. 0260 System timer error. 1.
Table 2. Numeric error codes (continued) Symptom or error FRU or action, in sequence 1805 Unauthorized Wireless USB card is plugged in—Power off and remove the Wireless USB card. 1. Remove the Wireless USB card that you installed. 2. System board. 1820 More than one external fingerprint reader is attached. Power off and remove all but the reader that you set up within your main operating system. Remove all but the reader that you set up for the authentication.
Error messages Table 3. Error messages Symptom or error FRU or action, in sequence Device address conflict. 1. Load “Setup Defaults” in the BIOS Setup Utility. 2. Backup battery. 3. System board. Allocation error for device. 1. Load “Setup Defaults” in the BIOS Setup Utility. 2. Backup battery. 3. System board. Failing bits: nnnn. 1. DIMM. 2. System board. Invalid system configuration data. 1. DIMM. 2. System board. I/O device IRQ conflict. 1. Load “Setup Defaults” in the BIOS Setup Utility. 2.
Beep symptoms Table 4. Beep symptoms Symptom or error FRU or action, in sequence One beep and a blank, unreadable, or flashing LCD. 1. 2. 3. 4. One long and two short beeps, and a blank or unreadable LCD. 1. System board. 2. LCD assembly. 3. DIMM. Two short beeps with error codes. POST error. See “Numeric error codes” on page 62. Two short beeps and a blank screen. 1. System board. 2. DIMM. Three short beeps, pause, three more short beeps, and one short beep. 1. DIMM. 2.
LCD-related symptoms Important: The TFT LCD for the notebook computer contains many thin-film transistors (TFTs). The presence of a small number of dots that are missing, discolored, or always lighted is characteristic of TFT LCD technology, but excessive pixel problems can cause viewing concerns. If the LCD you are servicing has two or less visible defective pixels, it should not be considered faulty.
Intermittent problems Intermittent system hang problems can be due to a variety of causes that have nothing to do with a hardware defect, such as cosmic radiation, electrostatic discharge, or software errors. FRU replacement should be considered only when a problem recurs. When analyzing an intermittent problem, do the following: 1. Run the diagnostic test for the system board in loop mode at least 10 times. 2. If no error is detected, do not replace any FRUs. 3.
70 ThinkPad T400s, T410s, and T410si Hardware Maintenance Manual
Status indicators This chapter presents the system status indicators that show the status of the computer.
Table 7. Status indicators Indicator Meaning 1 Orange: Speaker mute The speaker is on mute. To set the speakers on mute or unmute, press the speaker mute button. 2 72 Microphone mute Orange: 3 Wireless LAN, Wireless WAN, or WiMAX status Green: The wireless LAN feature (the IEEE 802.11 b/g standard, 802.11 a/b/g, or 802.11n), wireless WAN feature, or WiMax feature is on, and the radio link is ready for use, or the data is being transmitted.
Table 7. Status indicators (continued) Indicator Meaning 10 Sleep (standby for Windows XP) status Green: The computer is in sleep (standby) mode. Blinking green: The computer is entering sleep (standby) mode or hibernation mode, or is resuming normal operation. 11 Battery status Green: The battery has more than 20% charge. Orange: The battery has between 5% and 20% charge. Fast blinking orange: The battery has less than 5% charge. Note: The battery may be charging.
74 ThinkPad T400s, T410s, and T410si Hardware Maintenance Manual
Fn key combinations The following table shows the function of each combination of Fn with a function key. Table 8. Fn key combinations Key combination Description Fn+F1 Reserved. Fn+F2 Lock the computer. Fn+F3 Select a power plan (in Windows XP, power scheme) that has been created by Power Manager, or adjust the power level by using the slider control. When you press this combination, a panel for selecting a power plan (power scheme) appears. Notes: 1.
Table 8. Fn key combinations (continued) Key combination Description Fn+F7 Apply a presentation scheme directly, with no need to start Presentation Director. To disable this function and use the Fn+F7 key combination for switching a display output location, start Presentation Director, and change the settings. Note: If the computer is an Windows 7 model, it does not support presentation schemes, but the Fn+F7 combination is available for switching a display output location.
Table 8. Fn key combinations (continued) Key combination Description Fn+ScrLk Enable or disable the numeric keypad. The indicator of numeric lock will be displayed on the screen. Fn+Pause Has the same function as the Break key. Fn+cursor keys These key combinations work with Windows Media Player. Fn+down arrow key works for the Play or Pause button, Fn+up arrow key for the Stop button, Fn+right arrow key for the Next Track button, and Fn+left arrow key for the Previous Track button.
78 ThinkPad T400s, T410s, and T410si Hardware Maintenance Manual
FRU replacement notices This chapter presents notices related to removing and replacing parts. Read this chapter carefully before replacing any FRU. Screw notices Loose screws can cause a reliability problem. In the ThinkPad Notebook, this problem is addressed with special nylon-coated screws that have the following characteristics: v They maintain tight connections. v They do not easily come loose, even with shock or vibration. v They are harder to tighten. v Each one should be used only once.
Retaining serial numbers This section includes the following descriptions: v “Restoring the serial number of the system unit” v “Retaining the UUID” v “Reading or writing the ECA information” on page 81 Restoring the serial number of the system unit When the computer was manufactured, the EEPROM on the system board was loaded with the serial numbers of the system and all major components. These numbers need to remain the same throughout the life of the computer.
The algorithm that generates the number is designed to provide unique IDs until the year A.D. 3400. No two computers in the world have the same number. When you replace the system board, you must set the UUID on the new system board as follows: 1. Install the LENOVO ThinkPad Hardware Maintenance Diskette Version 1.76 or later, and restart the computer. 2. From the main menu, select 4. Assign UUID. A new UUID is created and written. If a valid UUID already exists, it is not overwritten.
82 ThinkPad T400s, T410s, and T410si Hardware Maintenance Manual
Removing and replacing a FRU This chapter presents directions and drawings for use in removing and replacing a FRU. Be sure to observe the following general rules: 1. Do not try to service any computer unless you have been trained and certified. An untrained person runs the risk of damaging parts. 2. Before replacing any FRU, review “FRU replacement notices” on page 79. 3. Begin by removing any FRUs that have to be removed before the failing FRU. Any such FRUs are listed at the top of the page.
Before servicing ThinkPad T400s, T410s, and T410si Removing the SIM card: Some models of the ThinkPad T400s, T410s, and T410si you are servicing might have the SIM card that the customer has installed. If the computer you are servicing has the SIM card, remove it before you start the servicing. To remove the SIM card, you need to remove the battery pack first. (See “1010 Battery pack” on page 85.) After you finish the servicing, make sure that you insert the card back into the slot firmly.
1010 Battery pack Important notice for replacing a battery pack: Lenovo ThinkVantage Toolbox (in Windows 7) and Lenovo System Toolbox (in Windows Vista and Windows XP) have an automatic battery diagnostic that determines if the battery pack is defective. A battery pack FRU should not be replaced unless this diagnostic shows that the battery is defective. The only exception to this is if the battery pack is physically damaged or a customer is reporting a possible safety issue.
1020 Serial Ultrabay Slim device or travel bezel For access, remove this FRU: v “1010 Battery pack” on page 85 Table 10. Removal steps of Serial Ultrabay Slim device or travel bezel Holding the bay lock latch in the unlocked position 1 , slide the bay eject latch 2 , and then pull out the Ultrabay Slim Media Bay device or the travel bezel in the direction shown by arrow 3 .
1030 Solid state drive (SSD) or hard disk drive (HDD) For access, remove these FRUs in order: v “1010 Battery pack” on page 85 Attention: v Do not drop the drive or apply any physical shock to it. The drive is sensitive to physical shock. Improper handling can cause damage and permanent loss of data. v Before removing the drive, have the user make a backup copy of all the information on it if possible. v Never remove the drive while the system is operating or is in suspend mode. Table 11.
Table 11. Removal steps of SSD or HDD (continued) 3 4 When installing: Make sure that the SSD connector or HDD connector is attached firmly.
1040 DIMM For access, remove these FRUs in order: v “1010 Battery pack” on page 85 Table 12. Removal steps of DIMM Note: Loosen the screws 1 , but do not remove them.
Table 12. Removal steps of DIMM (continued) Note: For ThinkPad T400s, if only one DIMM is used on the computer you are servicing, the card must be installed in SLOT-0 ( a ), but not in SLOT-1 ( b ).
Table 12. Removal steps of DIMM (continued) For ThinkPad T410s and T410si: 3 4 3 When installing: Insert the notched end of the DIMM into the socket. Press the DIMM firmly, and pivot it until it snaps into the place. Make sure that it is firmly fixed in the slot and does not move easily.
1050 PCI Express Mini Card for wireless LAN For access, remove these FRUs in order: v “1010 Battery pack” on page 85 Table 13. Removal steps of PCI Express Mini Card for wireless LAN Note: Loosen the screws 1 , but do not remove them.
Table 13. Removal steps of PCI Express Mini Card for wireless LAN (continued) In step 3 , unplug the jacks by using the removal tool antenna RF connector (P/N: 08K7159) or pick the connectors with your fingers and gently unplug them in direction of the arrow. Note: Some models might have only two antenna cables in step 3 . 4 4 Step 3 Screw (quantity) Color Torque Silver 0.181 Nm (1.85 kgfcm) Black 0.181 Nm (1.
Table 13. Removal steps of PCI Express Mini Card for wireless LAN (continued) 5 When installing: v In models with wireless LAN card that has two antenna connectors, plug the gray cable into the jack labeled MAIN or M, and the black cable into the jack labeled AUX or A on the card. If the computer you are servicing has three cables, put the white cable in the cable protection tube.
1060 PCI Express Mini Card for wireless WAN For access, remove these FRUs in order: v “1010 Battery pack” on page 85 Table 14. Removal steps of PCI Express Mini Card for wireless WAN Note: Loosen the screws 1 , but do not remove them.
Table 14. Removal steps of PCI Express Mini Card for wireless WAN (continued) In step 3 , unplug the jacks by using the removal tool antenna RF connector (P/N: 08K7159) or pick the connectors with your fingers and gently unplug them in direction of the arrow. 4 4 3 Step Screw (quantity) Color Torque Silver 0.181 Nm (1.85 kgfcm) Black 0.181 Nm (1.
Table 14. Removal steps of PCI Express Mini Card for wireless WAN (continued) 5 Note: Plug the orange cable into the jack labeled MAIN, and the blue cable into the jack labeled AUX on the card.
1070 Keyboard For access, remove these FRUs in order: v “1010 Battery pack” on page 85 Table 15. Removal steps of keyboard Note: Loosen the screws 1 , but do not remove them.
Table 15. Removal steps of keyboard (continued) 3 3 Step Screw (quantity) Color Torque 3 M2 × 6 mm, bind-head, nylon-coated (2) Black 0.181 Nm (1.85 kgfcm) Push down the keyboard a little toward the arrow 4 , and then lift up the keyboard in the direction of 5 .
Table 15. Removal steps of keyboard (continued) Lift the keyboard a little in the direction shown by arrow 6 , and then detach the connector 7 .
When installing the keyboard, do as follows: Table 16. Installation steps of keyboard 1. Attach the keyboard connector.
Table 16. Installation steps of keyboard (continued) 2. Attach the keyboard so that the keyboard edges a are under the frame as shown in this figure. a a a 3. To make sure that the front side of the keyboard is housed firmly, gently press the keys with your thumbs and try to slide the keyboard toward you. 4. Secure the keyboard by tightening the screws from the bottom side of the computer.
1080 Backup battery For access, remove these FRUs in order: v “1010 Battery pack” on page 85 v “1070 Keyboard” on page 98 DANGER Use only the battery specified in the parts list for your computer. Any other battery could ignite or explode. Table 17. Removal steps of backup battery 1 2 When installing: Attach the backup battery on the hole a in the insulation sheet as shown in the figure below and make sure that the battery connector is attached firmly.
1090 Wireless USB adapter or Intel Turbo Memory For access, remove these FRUs in order: v “1010 Battery pack” on page 85 v “1070 Keyboard” on page 98 Table 18. Removal steps of wireless USB adapter or Intel Turbo Memory Note: Step 1 is only for models with the wireless USB adapter. For models with the Intel® Turbo Memory Minicard, skip step 1 .
Table 18.
1100 Palm rest or palm rest with fingerprint reader For access, remove these FRUs in order: v “1010 Battery pack” on page 85 v “1030 Solid state drive (SSD) or hard disk drive (HDD)” on page 87 v “1070 Keyboard” on page 98 Note: In models with the fingerprint reader, the sensor is attached to the palm rest FRU. If the fingerprint reader has any defects, you can replace it by the procedures given in this section, which are the same for a palm rest with or without a fingerprint reader. Table 19.
Table 19.
1110 Bluetooth daughter card (BDC-2) v v v v “1010 Battery pack” on page 85 “1030 Solid state drive (SSD) or hard disk drive (HDD)” on page 87 “1070 Keyboard” on page 98 “1100 Palm rest or palm rest with fingerprint reader” on page 106 Table 20. Removal steps of BDC-2 1 2 Step Screw (quantity) Color Torque 1 M2 × 4 mm, bind-head, nylon-coated (1) Black 0.181 Nm (1.85 kgfcm) When installing: Make sure that the connector is attached firmly.
1120 Keyboard bezel and speaker assembly For access, remove these FRUs in order: v “1010 Battery pack” on page 85 v “1020 Serial Ultrabay Slim device or travel bezel” on page 86 v “1030 Solid state drive (SSD) or hard disk drive (HDD)” on page 87 v “1070 Keyboard” on page 98 v “1100 Palm rest or palm rest with fingerprint reader” on page 106 Table 21. Removal steps of keyboard bezel and speaker assembly Note: The speaker assembly is attached to the keyboard bezel.
Table 21. Removal steps of keyboard bezel and speaker assembly (continued) 2 2 3 3 2 4 Step Screw (quantity) Color Torque 2 M2 × 6 mm, bind-head, nylon-coated (3) Black 0.181 Nm (1.85 kgfcm) 3 M2 × 4 mm, bind-head, nylon-coated (2) Black 0.181 Nm (1.85 kgfcm) Silver 0.181 Nm (1.85 kgfcm) Black 0.181 Nm (1.
Table 21. Removal steps of keyboard bezel and speaker assembly (continued) 6 5 Note: Before step 8 , pull the cables out from the cable guide hole of the keyboard bezel as shown in the figure a .
Table 21. Removal steps of keyboard bezel and speaker assembly (continued) Turn the keyboard bezel over, and remove the speaker assembly. For ThinkPad T400s: 10 10 9 9 10 10 9 9 10 9 9 Step Screw (quantity) Color Torque 10 M2 × 3 mm, small-head, nylon-coated (5) Silver 0.181 Nm (1.85 kgfcm) For ThinkPad T410s and T410si: 10 10 9 9 10 9 10 9 112 Step Screw (quantity) Color Torque 10 M2 × 3 mm, small-head, nylon-coated (4) Black 0.181 Nm (1.
1130 5-in-1 Media Card Reader adapter For access, remove these FRUs in order: v “1010 Battery pack” on page 85 v “1020 Serial Ultrabay Slim device or travel bezel” on page 86 v “1030 Solid state drive (SSD) or hard disk drive (HDD)” on page 87 v “1070 Keyboard” on page 98 v “1100 Palm rest or palm rest with fingerprint reader” on page 106 v “1120 Keyboard bezel and speaker assembly” on page 109 Table 22.
1140 Bluetooth–wireless radio switch FPC For access, remove these FRUs in order: v “1010 Battery pack” on page 85 v “1020 Serial Ultrabay Slim device or travel bezel” on page 86 v “1030 Solid state drive (SSD) or hard disk drive (HDD)” on page 87 v “1070 Keyboard” on page 98 v “1100 Palm rest or palm rest with fingerprint reader” on page 106 v “1110 Bluetooth daughter card (BDC-2)” on page 108 v “1120 Keyboard bezel and speaker assembly” on page 109 Table 23.
Table 23. Removal steps of Bluetooth–wireless radio switch FPC (continued) When installing: Attach the wireless radio switch as shown in the figure a .
1150 LCD unit For access, remove these FRUs in order: v “1010 Battery pack” on page 85 v “1020 Serial Ultrabay Slim device or travel bezel” on page 86 v “1030 Solid state drive (SSD) or hard disk drive (HDD)” on page 87 v “1050 PCI Express Mini Card for wireless LAN” on page 92 v “1060 PCI Express Mini Card for wireless WAN” on page 95 v “1070 Keyboard” on page 98 v “1090 Wireless USB adapter or Intel Turbo Memory” on page 104 v “1100 Palm rest or palm rest with fingerprint reader” on page 106 v “1120 Keybo
Table 24. Removal steps of LCD unit (continued) 4 3 3 3 3 4 4 3 When installing: v Make sure that you route the cables firmly and tape up in the proper positions as shown in this figure. v When you route the cables, make sure that they are not subjected to any tension. Tension could cause the cables to be damaged by the cable guides, or a wire to be broken.
Table 24. Removal steps of LCD unit (continued) 5 6 When installing: Make sure that the connector is attached firmly.
Table 24.
1160 System board, fan assembly, and 34-mm ExpressCard slot frame Important notices for handling the system board: When handling the system board, bear the following in mind. v The system board has an accelerometer, which can be broken by applying several thousands of G-forces. Note: Dropping a system board from a height of as little as 6 inches so that it falls flat on a hard bench can subject the accelerometer to as much as 6,000 G’s of shock.
Table 25. Removal steps of system board, fan assembly, and 34-mm ExpressCard slot frame Following components soldered on the top side of the system board are extremely sensitive. When you service the system board, avoid any kind of rough handling.
Table 25.
Table 25. Removal steps of system board, fan assembly, and 34-mm ExpressCard slot frame (continued) 1 2 2a 1 1 Note: Step 2a is only for ThinkPad T410s and T410si. Step Screw (quantity) Color Torque 1 M2 × 3.5 mm, big-head, nylon-coated (3) Black 0.181 Nm (1.85 kgfcm) 2 M2 × 6 mm, bind-head, nylon-coated (1) Black 0.181 Nm (1.85 kgfcm) 2a M2 × 6 mm, bind-head, nylon-coated (2) Black 0.181 Nm (1.
Table 25. Removal steps of system board, fan assembly, and 34-mm ExpressCard slot frame (continued) Note: The steps from 5 to 7 indicate the removal steps of fan assembly, and those from 8 to 11 indicate the ones of 34-mm ExpressCard slot frame. 5a 5 5 5 Note: Step 5a is only for ThinkPad T410s and T410si. Step Screw (quantity) Color Torque 5 M2 × 3.5 mm, big-head, nylon-coated (3) Black 0.181 Nm (1.85 kgfcm) 5a M2 × 3.5 mm, big-head, nylon-coated (1) Black 0.181 Nm (1.
Table 25. Removal steps of system board, fan assembly, and 34-mm ExpressCard slot frame (continued) When installing: v Before you attach the fan assembly to the computer, apply thermal grease, at an amount of 0.2 grams, on the part marked a as in the following figure. Either too much or too less application of grease can cause a thermal problem due to imperfect contact with a component. You need to peel the thin film off from the rubber b .
Table 25. Removal steps of system board, fan assembly, and 34-mm ExpressCard slot frame (continued) For ThinkPad T400s: 8 9 9 Step Screw (quantity) Color Torque 8 M2 × 3 mm, small−head, nylon-coated (1) Silver 0.181 Nm (1.85 kgfcm) 9 M2 × 5 mm, flat−head, nylon-coated (2) Black 0.181 Nm (1.85 kgfcm) For ThinkPad T410s and T410si: 8 8 126 9 9 Step Screw (quantity) Color Torque 8 M2 × 3 mm, small−head, nylon-coated (2) Black 0.181 Nm (1.
Table 25. Removal steps of system board, fan assembly, and 34-mm ExpressCard slot frame (continued) Turn the system board over, and then remove the 34-mm ExpressCard slot frame from the system board.
1170 I/O sub card and base cover assembly For access, remove these FRUs in order: v “1010 Battery pack” on page 85 v “1020 Serial Ultrabay Slim device or travel bezel” on page 86 v “1030 Solid state drive (SSD) or hard disk drive (HDD)” on page 87 v “1050 PCI Express Mini Card for wireless LAN” on page 92 v “1060 PCI Express Mini Card for wireless WAN” on page 95 v “1070 Keyboard” on page 98 v “1090 Wireless USB adapter or Intel Turbo Memory” on page 104 v “1100 Palm rest or palm rest with fingerprint reade
Note: Applying labels to the base cover The new base cover FRU is shipped with a kit containing labels of several kinds. When you replace the base cover, you need to apply the following labels: 8 Blind sheet L 14 Homologation label Following labels need to be peeled off from the old base cover, and need to be put on the new base cover.
2010 LCD bezel assembly For access, remove the following FRU: v “1010 Battery pack” on page 85 Table 27. Removal steps of LCD bezel assembly 1 1 Step 1 130 Screw cap Screw (quantity) M2 × 3 mm, shoulder-socket head, nylon-coated (2) ThinkPad T400s, T410s, and T410si Hardware Maintenance Manual Color Torque Black 0.181 Nm (1.
Table 27.
2020 LCD latch L and R For access, remove the following FRU: v “1010 Battery pack” on page 85 v “2010 LCD bezel assembly” on page 130 Table 28. Removal steps of LCD latch L and R 1 1 When installing: Attach the LCD latch marked L to the left-hand side and the LCD latch marked R to the right-hand side.
2030 Integrated camera or microphone sub card For access, remove these FRUs, in order: v “1010 Battery pack” on page 85 v “2010 LCD bezel assembly” on page 130 Table 29. Removal steps of integrated camera or microphone sub card 4 1 2 3 Step Screw (quantity) Color Torque Silver 0.181 Nm (1.85 kgfcm) Black 0.181 Nm (1.
Table 29.
2040 LED sub card For access, remove these FRUs in order: v “1010 Battery pack” on page 85 v “2010 LCD bezel assembly” on page 130 Table 30. Removal steps of LED sub card For ThinkPad T400s: 1 2 Step Screw (quantity) Color Torque 1 M2 × 3 mm, small-head, nylon-coated (1) Silver 0.181 Nm (1.85 kgfcm) 3 When installing: Make sure that the connector is attached firmly.
Table 30. Removal steps of LED sub card (continued) For ThinkPad T410s and T410si: 1 2 Step Screw (quantity) Color Torque 1 M2 × 3 mm, small-head, nylon-coated (1) Black 0.181 Nm (1.85 kgfcm) 3 4 When installing: Make sure that the connector is attached firmly.
2050 LCD panel For access, remove these FRUs, in order: v “1010 Battery pack” on page 85 v “2010 LCD bezel assembly” on page 130 Important notice on handling the LCD panel: The LCD panel and the peripheral parts used in this product are very sensitive. Improper handling of the LCD panel can cause damage to the parts, and may cause a system malfunction such as a missing dot, missing line, or pixel problems. v DO NOT apply any kind of pressure to the LCD panel.
Table 31. Removal steps of LCD panel 1 Attention: Unplug the LCD cable with holding the left and right edges of the connector with your fingers, and gently pull the connector toward you. DO NOT unplug it with pulling the cable. Applying tension could cause the cable to be damaged or a wire to be broken. When installing: v Place the LCD panel on a soft and clean sheet spread on a flat table, and plug the cable by pushing the left and right edges of the connector little by little with your fingers.
Table 31. Removal steps of LCD panel (continued) When installing: When attaching the LCD panel to the cover, press the left and right edges covered with metal gently with your fingers. DO NOT press the surface of the panel or apply any excessive force to the panel.
2060 LCD cable For access, remove these FRUs, in order: v “1010 Battery pack” on page 85 v “1020 Serial Ultrabay Slim device or travel bezel” on page 86 v “1030 Solid state drive (SSD) or hard disk drive (HDD)” on page 87 v “1050 PCI Express Mini Card for wireless LAN” on page 92 v “1060 PCI Express Mini Card for wireless WAN” on page 95 v “1070 Keyboard” on page 98 v “1090 Wireless USB adapter or Intel Turbo Memory” on page 104 v “1100 Palm rest or palm rest with fingerprint reader” on page 106 v “1120 Key
2070 Hinge kit For access, remove these FRUs in order: v “1010 Battery pack” on page 85 v “1020 Serial Ultrabay Slim device or travel bezel” on page 86 v “1030 Solid state drive (SSD) or hard disk drive (HDD)” on page 87 v “1050 PCI Express Mini Card for wireless LAN” on page 92 v “1060 PCI Express Mini Card for wireless WAN” on page 95 v “1070 Keyboard” on page 98 v “1090 Wireless USB adapter or Intel Turbo Memory” on page 104 v “1100 Palm rest or palm rest with fingerprint reader” on page 106 v “1120 Keyb
Table 33. Removal steps of hinge kit (continued) 2 2 Cable routing: When you install the hinge kit, route the cables as shown in the figure below.
2080 LED cable For access, remove these FRUs in order: v “1010 Battery pack” on page 85 v “1020 Serial Ultrabay Slim device or travel bezel” on page 86 v “1030 Solid state drive (SSD) or hard disk drive (HDD)” on page 87 v “1050 PCI Express Mini Card for wireless LAN” on page 92 v “1060 PCI Express Mini Card for wireless WAN” on page 95 v “1070 Keyboard” on page 98 v “1090 Wireless USB adapter or Intel Turbo Memory” on page 104 v “1100 Palm rest or palm rest with fingerprint reader” on page 106 v “1120 Keyb
Table 34. Removal steps of LED cable (continued) Cable routing: When you install the LED cable, route the cable as shown in the figure below.
2090 Antenna kit and LCD rear cover assembly For access, remove these FRUs in order: v “1010 Battery pack” on page 85 v “1020 Serial Ultrabay Slim device or travel bezel” on page 86 v “1030 Solid state drive (SSD) or hard disk drive (HDD)” on page 87 v “1050 PCI Express Mini Card for wireless LAN” on page 92 v “1060 PCI Express Mini Card for wireless WAN” on page 95 v “1070 Keyboard” on page 98 v “1090 Wireless USB adapter or Intel Turbo Memory” on page 104 v “1100 Palm rest or palm rest with fingerprint re
Table 35. Removal steps of antenna kit and LCD rear cover assembly (continued) 2 2 Cable routing: When you install the antenna kit, route the cables as shown in the figures below. As you route the cables, make sure that they are not subjected to any tension. Tension could cause the cables to be damaged by the cable guides, or a wire to be broken.
Locations This chapter presents the location of ThinkPad T400s, T410s, and T410si features and hardware. Front view 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 Integrated camera (for some models) ThinkLight Built-in microphone Status indicators Note: For the description of each indicator, see “Status indicators” on page 71.
Rear view 1 2 3 4 5 6 7 8 9 Status indicators Note: For the description of each indicator, see “Status indicators” on page 71.
Bottom view 1 2 3 4 5 6 7 8 Expansion slot (DIMM, PCI Express Mini Card for wireless LAN and wireless WAN) Docking connector Solid state drive (SSD) or hard disk drive (HDD) Battery pack Battery pack latch LCD cover latch Ultrabay Slim Media Bay lock latch Ultrabay Slim Media Bay eject latch 8 7 1 2 6 5 4 3 Locations 149
150 ThinkPad T400s, T410s, and T410si Hardware Maintenance Manual
Parts list This chapter contains following lists of the service parts. v “Overall” on page 152 v “LCD FRUs” on page 171 v “Keyboard” on page 183 v “Miscellaneous parts” on page 184 v “AC adapters” on page 187 v “Power cords” on page 188 v “Recovery discs” on page 189 v “Common service tools” on page 204 Notes: v Each FRU is available for all types or models, unless specific types or models are specified.
Overall 1 22 21 20 2 19 18 3 17 4 16 15 5 14 6 13 12 7 11 8 b 9 a 10 152 ThinkPad T400s, T410s, and T410si Hardware Maintenance Manual
Table 36. Parts list—Overall No. a, b FRU (Overall) FRU no. CRU ID See “Miscellaneous parts” on page 184. 1 LCD unit (see “LCD FRUs” on page 171.
Table 36. Parts list—Overall (continued) No. FRU (Overall) FRU no.
Table 36. Parts list—Overall (continued) No. FRU (Overall) FRU no.
Table 36. Parts list—Overall (continued) No. FRU (Overall) FRU no.
Table 36. Parts list—Overall (continued) No. FRU (Overall) FRU no. CRU ID 6 60Y3213 Bluetooth daughter card (BDC-2.
Table 36. Parts list—Overall (continued) No. FRU (Overall) FRU no.
Table 36. Parts list—Overall (continued) No. FRU (Overall) FRU no.
Table 36. Parts list—Overall (continued) No. FRU (Overall) FRU no.
Table 36. Parts list—Overall (continued) No. FRU (Overall) FRU no.
Table 36. Parts list—Overall (continued) No. FRU (Overall) FRU no.
Table 36. Parts list—Overall (continued) No. FRU (Overall) FRU no.
Table 36. Parts list—Overall (continued) No. FRU (Overall) FRU no.
Table 36. Parts list—Overall (continued) No. FRU (Overall) FRU no.
Table 36. Parts list—Overall (continued) No. FRU (Overall) FRU no.
Table 36. Parts list—Overall (continued) No. FRU (Overall) FRU no.
Table 36. Parts list—Overall (continued) No. FRU (Overall) FRU no.
Table 36. Parts list—Overall (continued) No. 18 FRU (Overall) FRU no.
Table 36. Parts list—Overall (continued) No. FRU (Overall) FRU no.
LCD FRUs In ThinkPad T400s, T410s, and T410si, there are following types of LCDs. v 14.1-inch WXGA+ TFT LED-backlight LCD (Table 37 on page 172) v 14.
Table 37. Parts list—14.1-inch WXGA+ LED-backlight LCD No. FRU (14.1-inch WXGA+ LED-backlight LCD) FRU no. CRU ID 1 LCD bezel assembly 45M2653 N 2 LCD module, 14.1-inch WXGA+ 27R2479 N 2 LCD module, 14.
Table 37. Parts list—14.1-inch WXGA+ LED-backlight LCD (continued) No. 5 FRU (14.1-inch WXGA+ LED-backlight LCD) FRU no.
Table 37. Parts list—14.1-inch WXGA+ LED-backlight LCD (continued) No. FRU (14.1-inch WXGA+ LED-backlight LCD) FRU no.
Table 37. Parts list—14.1-inch WXGA+ LED-backlight LCD (continued) No. 7 FRU (14.1-inch WXGA+ LED-backlight LCD) FRU no.
Table 37. Parts list—14.1-inch WXGA+ LED-backlight LCD (continued) No. 8 176 FRU (14.1-inch WXGA+ LED-backlight LCD) FRU no.
Table 37. Parts list—14.1-inch WXGA+ LED-backlight LCD (continued) No. 8 FRU (14.1-inch WXGA+ LED-backlight LCD) FRU no.
Table 37. Parts list—14.1-inch WXGA+ LED-backlight LCD (continued) No. FRU (14.1-inch WXGA+ LED-backlight LCD) FRU no.
Table 37. Parts list—14.1-inch WXGA+ LED-backlight LCD (continued) No. 11 FRU (14.1-inch WXGA+ LED-backlight LCD) FRU no.
Table 38. Parts list—14.1-inch WXGA+ LED-backlight Multi touch panel No. FRU (14.1-inch WXGA+ LED-backlight Multi touch panel ) FRU no. CRU ID 1 LCD bezel assembly (touch panel) 60Y4330 N 2 LCD module, 14.1-inch WXGA+ 27R2479 N 2 LCD module, 14.
Table 38. Parts list—14.1-inch WXGA+ LED-backlight Multi touch panel (continued) No. FRU (14.1-inch WXGA+ LED-backlight Multi touch panel ) FRU no.
Table 38. Parts list—14.1-inch WXGA+ LED-backlight Multi touch panel (continued) No. FRU (14.1-inch WXGA+ LED-backlight Multi touch panel ) FRU no.
Keyboard Table 39. Parts list—Keyboard Language FRU no.
Miscellaneous parts Table 40. Parts list—Miscellaneous parts FRU FRU no. CRU ID Screw kit for T400s: v M2 × 3 mm (silver), small head (20) v M2 × 4 mm (black), bind head (20) v M2 × 5 mm (black), flat head (6) v M2 × 6 mm (black), bind head (20) v M2 × 6 mm (silver), flat head (10) v M2 × 3.5 mm (black), big head (20) v M2.5 × 6.5 mm (black), flat head (10) v Shoulder screw M2 × 3 mm (black) (front bezel) (6) v Shoulder screw M2 × 1.
Table 40. Parts list—Miscellaneous parts (continued) FRU FRU no.
Table 40. Parts list—Miscellaneous parts (continued) FRU FRU no.
AC adapters Table 41. Parts list—2-pin AC adapters FRU FRU no.
Power cords A ThinkPad power cord for a specific country or region is usually available only in that country or region: Table 44. Parts list—2-pin power cords Country or region FRU no. CRU ID Argentina v models -CTO, xxY 42T5020 42T5105 * Brazil v models -CTO, xxP 42T5180 42T5183 Canada, U.S. v models -CTO, xxF, xxL, xxS, xxU 42T5008 42T5093 Japan v models -CTO, xxE, xxJ 42T5014 42T5099 Table 45. Parts list—3-pin power cords 188 Country or region FRU no.
Recovery discs Windows XP Professional (32 bit) DVDs Windows XP Professional (32 bit) is preinstalled as the operating system in the following models: v 2801-CTO, A3x, A5x, A7x, AAx, ACx, AEx, AFx, AGx v 2808-CTO, C4x, C8x, CHx, CJx, CNx, CPx, CZx, D2x, D3x, D4x, D5x, D6x, D7x, D8x, DHx, DJx, DKx, DVx, DWx, DYx, DZx, E2x, EAx, EBx, EFx, EGx, EKx, EMx, EPx, EQx, ERx, ESx, ETx, EUx, EXx, EZx, FEx, FFx, FKx, FLx v 2809-CTO, 76x, 79x, 7Ex v 2815-CTO, 22x, 35x, 38x, 4Hx, 5Fx, 5Gx, 5Hx, 5Jx, 5Kx, 5Lx, 5Mx, 5Rx, 5
Table 46.
Windows Vista Starter Edition (32 bit) DVDs Windows Vista Starter Edition (32 bit) is preinstalled as the operating system in the following models: v 2801-CTO v 2808-CTO v 2809-CTO v 2815-CTO v 2823-CTO v 2824-CTO v 2825-CTO Table 47.
Windows Vista Home Basic (32 bit) DVDs Windows Vista Home Basic (32 bit) is preinstalled as the operating system in the following models: v 2801-CTO v 2808-CTO v 2809-CTO, 73x v 2815-CTO, 32x v 2823-CTO v 2824-CTO v 2825-CTO Table 48.
Windows Vista Home Premium (32 bit) DVDs Windows Vista Home Premium (32 bit) is preinstalled as the operating system in the following models: v 2801-CTO, A9x, AHx, AJx, AKx, ANx, APx v 2808-CTO v 2809-CTO v 2815-CTO v 2823-CTO v 2824-CTO v 2825-CTO Table 49.
Windows Vista Business (32 bit) DVDs Windows Vista Business (32 bit) is preinstalled as the operating system in the following models: v 2801-CTO, A2x, A4x, A6x, A8x, ABx, ADx v 2808-CTO, C2x, C3x, C5x, C6x, C7x, C9x, CAx, CBx, CCx, CDx, CEx, CFx, CKx, CLx, CQx, CRx, CSx, CUx, CVx, CWx, CXx, CYx, E5x, E6x, E7x, E8x, ECx, EDx, EHx, EJx, FBx, FCx, FGx, FHx v 2809-CTO, 72x, 75x, 77x, 78x, 7Ax, 7Bx, 7Cx, 7Dx v 2815-CTO, 20x, 23x, 24x, 25x, 2Ax, 2Bx, 2Cx, 2Dx, 2Ex, 2Fx, 2Gx, 2Hx, 2Jx, 2Kx, 2Lx, 2Mx, 2Nx, 2Px, 2Rx
Table 50.
Windows Vista Business (64 bit) DVDs Windows Vista Business (64 bit) is preinstalled as the operating system in the following models: v 2801-CTO v 2808-CTO, CGx, CMx, E9x, EEx, FDx, FJx v 2809-CTO v 2815-CTO, 3Px, 3Rx v 2823-CTO, 9Gx, 9Qx v 2824-CTO v 2825-CTO Table 51.
Windows Vista Ultimate (32 bit) DVDs Windows Vista Ultimate (32 bit) is preinstalled as the operating system in the following models: v 2801-CTO v 2808-CTO v 2809-CTO v 2815-CTO, 2Qx, 2Tx, 3Nx, 3Qx v 2823-CTO, 9Fx, 9Px v 2824-CTO v 2825-CTO Table 52.
Windows 7 Home Basic (32 bit) DVDs Windows 7 Home Basic (32 bit) is preinstalled as the operating system in the following models: v 2801-CTO v 2808-CTO v 2809-CTO v 2815-CTO, 4Ux v 2823-CTO v 2824-CTO v 2825-CTO v 2901-CTO, A5x, A8x, ABx, ACx, AEx, AGx v 2904-CTO, D6x, D7x, FHx, FJx v 2907-CTO, 73x, 76x v 2912-CTO, 3Gx v 2924-CTO, 9Ax Table 53.
Windows 7 Home Premium (32 bit) DVDs Windows 7 Home Premium (32 bit) is preinstalled as the operating system in the following models: v 2801-CTO, AMx v 2808-CTO v 2809-CTO v 2815-CTO v 2823-CTO v 2824-CTO v 2825-CTO v 2901-CTO v 2904-CTO, CPx, CRx, F5x v 2907-CTO v 2912-CTO, 2Xx, 32x v 2924-CTO Table 54.
Windows 7 Home Premium (64 bit) DVDs Windows 7 Home Premium (64 bit) is preinstalled as the operating system in the following models: v 2801-CTO, AQx v 2808-CTO v 2809-CTO v 2815-CTO v 2823-CTO v 2824-CTO v 2825-CTO v 2901-CTO v 2904-CTO, DMx v 2907-CTO v 2912-CTO v 2924-CTO Table 55.
Windows 7 Professional (32 bit) DVDs Windows 7 Professional (32 bit) is preinstalled as the operating system in the following models: v 2801-CTO, ALx v 2808-CTO, D9x, DAx, DBx, DCx, DDx, DEx, DFx, DGx, DMx, DNx, DPx, DQx, DRx, DSx, DTx, DUx, DXx, E4x, ELx, ENx, EVx, EWx, F3x, F4x, F5x, F6x, F7x, F8x, F9x, FAx, FNx v 2809-CTO v 2815-CTO, 3Zx, 42x, 43x, 44x, 45x, 46x, 47x, 48x, 49x, 4Ax, 4Bx, 4Cx, 4Dx, 4Fx, 4Jx, 4Lx, 4Nx, 4Qx, 4Sx, 4Vx, 4Xx, 5Nx, 5Px, 5Qx, 5Tx, 5Ux, 5Xx v 2823-CTO v 2824-CTO v 2825-CTO v 2901
Table 56.
Windows 7 Professional (64 bit) DVDs Windows 7 Professional (64 bit) is preinstalled as the operating system in the following models: v 2801-CTO v 2808-CTO, DLx, E3x v 2809-CTO v 2815-CTO, 4Ex, 4Gx, 4Wx, 5Yx v 2823-CTO v 2824-CTO v 2825-CTO v 2901-CTO v 2904-CTO, DGx, DNx, DPx, F4x, F9x, FAx, FCx, FDx v 2907-CTO v 2912-CTO, 36x, 3Ax, 3Lx v 2924-CTO Table 57.
Common service tools Table 58. Parts list—Common service tools Tool P/N Screwdriver kit 95F3598 1/4″ drive spinner handle 1650840 1/4″ Sq. to 1/4″ hex torx adapter 93F2838 TR7-TR-10 tamper resistant torx bits 00P6967 Removal tool antenna RF connector 08K7159 USB 2.
Notices Lenovo may not offer the products, services, or features discussed in this document in all countries. Consult your local Lenovo representative for information on the products and services currently available in your area. Any reference to a Lenovo product, program, or service is not intended to state or imply that only that Lenovo product, program, or service may be used.
vary significantly. Some measurements may have been made on development-level systems and there is no guarantee that these measurements will be the same on generally available systems. Furthermore, some measurements may have been estimated through extrapolation. Actual results may vary. Users of this document should verify the applicable data for their specific environment.
Part Number: 45M2271_02 (1P) P/N: 45M2271_02
