ThinkPad T510, T510i, and W510 Hardware Maintenance Manual
ThinkPad T510, T510i, and W510 Hardware Maintenance Manual
Note Before using this information and the product it supports, be sure to read the general information under “Notices” on page 201. First Edition (December 2009) © Copyright Lenovo 2009. LENOVO products, data, computer software, and services have been developed exclusively at private expense and are sold to governmental entities as commercial items as defined by 48 C.F.R. 2.101 with limited and restricted rights to use, reproduction and disclosure.
Contents About this manual . . . . . . . . . . v Safety information . . . . . . . . . . 1 General safety . . . . . . . . . . . . . . 2 Electrical safety . . . . . . . . . . . . . 3 Safety inspection guide . . . . . . . . . . . 5 Handling devices that are sensitive to electrostatic discharge . . . . . . . . . . . . . . . 6 Grounding requirements . . . . . . . . . . 6 Safety notices (multilingual translations) . . . . . 7 Laser compliance statement (multilingual translations) . . . . . . . . . . . . . .
2040 LCD cable, camera cable, LCD panel, and hinges . . . . . . . . . . . . . . . 2050 Antenna kit and LCD rear cover assembly . 132 135 Locations . . . . . . . . . . . . . 137 Front view . Rear view . Bottom view. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 137 . 139 . 140 Parts list . . . . . . . . . . . . . 141 Overall . . LCD FRUs . Keyboard. . Miscellaneous iv . . . . . . parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
About this manual This manual contains service and reference information for the following ThinkPad® products. ThinkPad T510 and T510i MT 4313, 4314, 4339, 4349, 4384, 4873, and 4484 ThinkPad W510 MT 4318, 4319, 4387, 4389, 4391, 4875, and 4876 Use this manual along with the advanced diagnostic tests to troubleshoot problems. Important: This manual is intended only for trained service technicians who are familiar with ThinkPad products.
vi ThinkPad T510, T510i, and W510 Hardware Maintenance Manual
Safety information This chapter presents following safety information that you need to be familiar with before you service a ThinkPad Notebook.
General safety Follow these rules to ensure general safety: v Observe good housekeeping in the area of the machines during and after maintenance. v When lifting any heavy object: 1. Make sure that you can stand safely without slipping. 2. Distribute the weight of the object equally between your feet. 3. Use a slow lifting force. Never move suddenly or twist when you attempt to lift. 4. Lift by standing or by pushing up with your leg muscles; this action removes the strain from the muscles in your back.
Electrical safety Observe the following rules when working on electrical equipment. Important: Use only approved tools and test equipment. Some hand tools have handles covered with a soft material that does not insulate you when working with live electrical currents. Many customers have, near their equipment, rubber floor mats that contain small conductive fibers to decrease electrostatic discharges. Do not use this type of mat to protect yourself from electrical shock.
v Do not touch live electrical circuits with the reflective surface of a plastic dental mirror. The surface is conductive; such touching can cause personal injury and machine damage. v Do not service the following parts with the power on when they are removed from their normal operating places in a machine: – Power supply units – Pumps – Blowers and fans – Motor generators – Similar units to listed above This practice ensures correct grounding of the units.
Safety inspection guide The purpose of this inspection guide is to assist you in identifying potentially unsafe conditions. As each machine was designed and built, required safety items were installed to protect users and service technicians from injury. This guide addresses only those items. You should use good judgment to identify potential safety hazards due to attachment of non-ThinkPad features or options not covered by this inspection guide.
Handling devices that are sensitive to electrostatic discharge Any computer part containing transistors or integrated circuits (ICs) should be considered sensitive to electrostatic discharge (ESD.) ESD damage can occur when there is a difference in charge between objects. Protect against ESD damage by equalizing the charge so that the machine, the part, the work mat, and the person handling the part are all at the same charge. Notes: 1.
Safety notices (multilingual translations) The safety notices in this section are provided in the following languages: v English v Arabic v Brazilian Portuguese v French v German v Hebrew v Japanese v Korean v Spanish v Traditional Chinese Safety information 7
DANGER Before the computer is powered on after FRU replacement, make sure all screws, springs, and other small parts are in place and are not left loose inside the computer. Verify this by shaking the computer and listening for rattling sounds. Metallic parts or metal flakes can cause electrical shorts. DANGER Some standby batteries contain a small amount of nickel and cadmium. Do not disassemble a standby battery, recharge it, throw it into fire or water, or short-circuit it.
DANGER To avoid shock, do not remove the plastic cover that protects the lower part of the inverter card. DANGER Though the main batteries have low voltage, a shorted or grounded battery can produce enough current to burn personnel or combustible materials. DANGER Unless hot swap is allowed for the FRU being replaced, do as follows before removing it: power off the computer, unplug all power cords from electrical outlets, remove the battery pack, and disconnect any interconnecting cables.
10 ThinkPad T510, T510i, and W510 Hardware Maintenance Manual
Safety information 11
PERIGO Antes de ligar o computador após a substituição da FRU, certifique-se de que todos os parafusos, molas e outras peças pequenas estejam no lugar e não estejam soltos dentro do computador. Verifique isso sacudindo o computador e procurando ouvir sons de peças soltas. Peças metálicas ou lascas de metal podem causar curto-circuito. PERIGO Algumas baterias reserva contêm uma pequena quantidade de níquel e cádmio.
PERIGO Para evitar choque elétrico, não remova a capa plástica que protege a parte inferior da placa inversora. PERIGO Embora as principais baterias possuam baixa voltagem, uma bateria em curto-circuito ou aterrada pode produzir corrente o bastante para queimar materiais de pessoal ou inflamáveis.
DANGER Avant de remettre l’ordinateur sous tension après remplacement d’une unité en clientèle, vérifiez que tous les ressorts, vis et autres pièces sont bien en place et bien fixées. Pour ce faire, secouez l’unité et assurez-vous qu’aucun bruit suspect ne se produit. Des pièces métalliques ou des copeaux de métal pourraient causer un court-circuit. DANGER Certaines batteries de secours contiennent du nickel et du cadmium. Ne les démontez pas, ne les rechargez pas, ne les exposez ni au feu ni à l’eau.
DANGER Afin d’éviter tout risque de choc électrique, ne retirez pas le cache en plastique protégeant la partie inférieure de la carte d’alimentation. DANGER Bien que le voltage des batteries principales soit peu élevé, le court-circuit ou la mise à la masse d’une batterie peut produire suffisamment de courant pour brûler des matériaux combustibles ou causer des brûlures corporelles graves.
VORSICHT Bevor nach einem FRU-Austausch der Computer wieder angeschlossen wird, muß sichergestellt werden, daß keine Schrauben, Federn oder andere Kleinteile fehlen oder im Gehäuse vergessen wurden. Der Computer muß geschüttelt und auf Klappergeräusche geprüft werden. Metallteile oder-splitter können Kurzschlüsse erzeugen. VORSICHT Die Bereitschaftsbatterie, die sich unter dem Diskettenlaufwerk befindet, kann geringe Mengen Nickel und Cadmium enthalten.
VORSICHT Die Leuchtstoffröhre im LCD-Bildschirm enthält Quecksilber. Bei der Entsorgung die örtlichen Bestimmungen für Sondermüll beachten. Der LCD-Bildschirm besteht aus Glas und kann zerbrechen, wenn er unsachgemäß behandelt wird oder der Computer auf den Boden fällt.
18 ThinkPad T510, T510i, and W510 Hardware Maintenance Manual
Safety information 19
20 ThinkPad T510, T510i, and W510 Hardware Maintenance Manual
Safety information 21
22 ThinkPad T510, T510i, and W510 Hardware Maintenance Manual
Safety information 23
PELIGRO Antes de encender el sistema despues de sustituir una FRU, compruebe que todos los tornillos, muelles y demás piezas pequeñas se encuentran en su sitio y no se encuentran sueltas dentro del sistema. Compruébelo agitando el sistema y escuchando los posibles ruidos que provocarían. Las piezas metálicas pueden causar cortocircuitos eléctricos. PELIGRO Algunas baterías de reserva contienen una pequeña cantidad de níquel y cadmio.
PELIGRO Para evitar descargas, no quite la cubierta de plástico que rodea la parte baja de la tarjeta invertida. PELIGRO Aunque las baterías principales tienen un voltaje bajo, una batería cortocircuitada o con contacto a tierra puede producir la corriente suficiente como para quemar material combustible o provocar quemaduras en el personal.
26 ThinkPad T510, T510i, and W510 Hardware Maintenance Manual
Safety information 27
Laser compliance statement (multilingual translations) The laser compliance statements in this section are provided in the following languages: v English v Arabic v Brazilian Portuguese v French v German v Hebrew v Japanese v Korean v Spanish v Traditional Chinese Some models of ThinkPad Notebook are equipped from the factory with an optical storage device such as a CD-ROM drive or a DVD-ROM drive. Such devices are also sold separately as options.
Safety information 29
Alguns modelos de computador ThinkPad são equipados na fábrica com um dispositivo de armazenamento ótico, como uma unidade de CD-ROM ou de DVD-ROM. Tais dispositivos também são vendidos separadamente como opcionais. Se uma dessas unidades estiver instalada, ela é certificada nos Estados Unidos em conformidade com os requisitos do Department of Health and Human Services 21 Code of Federal Regulations (DHHS 21 CFR), Subcapítulo J, para produtos a laser da Classe 1.
Certains modèles d’ordinateur ThinkPad sont équipés d’origine d’une unité de stockage optique telle qu’une unité de CD-ROM ou de DVD-ROM. Ces unités sont également vendues séparément en tant qu’options. Si l’une de ces unités est installée, elle est certifiée conforme, aux Etats-Unis, aux normes indiquées dans le sous-chapitre J du DHHS 21 CFR relatif aux produits à laser de classe 1.
Einige ThinkPad-Modelle sind werkseitig mit einem CD-ROM- oder DVD-ROM-Laufwerk ausgestattet. CD- und DVD-Laufwerke können auch gesondert als Zusatzeinrichtung erworben werden. Die Laufwerke erfüllen die Anforderungen gemäß IEC 60825-1 (International Electrotechnical Commission) und gemäß CENELEC EN 60825-1 für Laserprodukte der Klasse 1.
Safety information 33
34 ThinkPad T510, T510i, and W510 Hardware Maintenance Manual
Safety information 35
Algunos modelos de sistemas ThinkPad están equipados de fábrica con un dispositivo de almacenamiento óptico, como una unidad de CD-ROM o de DVD-ROM. Estas unidades también se venden por separado como opciones. Si está instalada alguna de dichas unidades, se certifica que en los Estados Unidos cumple los requisitos del Department of Health and Human Services 21 Code of Federal Regulations (DHHS 21 CFR) Subchapter J para productos láser de Clase 1.
Safety information 37
38 ThinkPad T510, T510i, and W510 Hardware Maintenance Manual
Important service information This chapter presents following important service information that applies to all machine types supported by this manual: v “Strategy for replacing FRUs” – “Strategy for replacing a hard disk drive” on page 40 – “Important notice for replacing a system board” on page 40 – “How to use error message” on page 40 v “Strategy for replacing FRUs for CTO, CMV, and GAV” on page 41 – “Product definition” on page 41 – “FRU identification for CTO, CMV, and GAV products” on page 41 Import
Use the following strategy to prevent unnecessary expense for replacing and servicing FRUs: v If you are instructed to replace a FRU but the replacement does not correct the problem, reinstall the original FRU before you continue. v Some computers have both a processor board and a system board. If you are instructed to replace either the processor board or the system board, and replacing one of them does not correct the problem, reinstall that board, and then replace the other one.
Strategy for replacing FRUs for CTO, CMV, and GAV Product definition Dynamic Configure To Order (CTO) This provides the ability for a customer to configure an IBM® or a Lenovo solution from an eSite, and have this configuration sent to fulfillment, where it is built and shipped directly to the customer. The machine label, Product Entitlement Warehouse (PEW), eSupport, and the HMM will load these products as the 4-digit MT and 3-digit model, where model = “CTO” (Example: 1829-CTO).
v Business Partners using Eclaim will access PEW when performing Entitlement Lookup. Business Partners will enter Loc ID, MT and Serial, and the key commodities will be returned in the Eclaim record under SYSTEM DETAILS. v Authorized IBM Business Partners can access Eclaim at the following Web site: https://wca.eclaim.
General checkout This chapter presents following information: v “What to do first” on page 44 v “Checkout guide” on page 45 – “Diagnostics using PC-Doctor for DOS” on page 45 – “Lenovo ThinkVantage Toolbox (Lenovo System Toolbox)” on page 48 – “PC-Doctor for Rescue and Recovery” on page 48 – “FRU tests” on page 49 v “Power system checkout” on page 51 The descriptions in this chapter apply to any ThinkPad model that supports the PC-Doctor® for DOS diagnostics program.
What to do first When you do return a FRU, you must include the following information in the parts exchange form or parts return form that you attach to it: __ 1. Name and phone number of service technician __ 2. Date of service __ 3. Date on which the machine failed __ 4. Date of purchase __ 5. Failure symptoms, error codes appearing on the display, and beep symptoms __ 6. Procedure index and page number in which the failing FRU was detected __ 7. Failing FRU name and part number __ 8.
Checkout guide Use the following procedures as a guide in identifying and correcting problems with the ThinkPad Notebook. Note: The diagnostic tests are intended to test only ThinkPad products. The use of non-ThinkPad products, prototype cards, or modified options can lead to false indications of errors and invalid system responses. 1. Identify the failing symptoms in as much detail as possible. 2. Verify the symptoms.
Testing the computer Note: The PC-Doctor diagnostic CD does not support any optical drives connected through USB devices or any others. It supports only the internal optical drive of the ThinkPad Notebook. To run the test, do as follows: 1. Turn off the computer. 2. Make sure that the internal optical drive that is supported as a startup device is attached to the computer. 3. Turn on the computer. If the computer cannot be powered on, go to “Power system checkout” on page 51, and check the power sources.
The options on the test menu are as follows: Diagnostics v v v v v v v v v v v v Run Normal Test Run Quick Test CPU/Coprocessor System board Video Adapter Fixed Disks Diskette Drives Other Devices ThinkPad Devices Communication Wireless LAN Advanced Memory Tests Interactive Tests v v v v v v v v Keyboard Video Internal Speaker Mouse Diskette System Load Optical Drive Test Intel WLAN Radio Test Note: v In the Keyboard test in Interactive Tests, the Fn key should be held down for at least 2 seconds; other
v v v v v v Battery Rundown View Test Log Print Log Save Log Full Erase Hard Drive Quick Erase Hard Drive Lenovo ThinkVantage Toolbox (Lenovo System Toolbox) Lenovo ThinkVantage® Toolbox (Lenovo System Toolbox in Windows Vista® and Windows® XP) is a diagnostic program that works through the Windows operating system.
FRU tests The following table shows the test for each FRU. Table 1. FRU tests FRU Applicable test System board 1. Diagnostics --> CPU/Coprocessor 2. Diagnostics --> Systemboard 3. If the docking station or the port replicator is attached to the ThinkPad Notebook, detach it. 4. Place the computer on a horizontal surface, and run Diagnostics --> ThinkPad Devices --> HDD Active Protection Test. Note: Do not apply any physical shock to the computer while the test is running.
Table 1. FRU tests (continued) FRU Applicable test Memory 1. If two DIMMs are installed, remove one of them and run Diagnostics --> Advanced Memory Tests. 2. If the problem does not recur, return the DIMM to its place, remove the other one, and run the test again. TrackPoint or pointing device If the TrackPoint does not work, check the configuration as specified in the BIOS Setup Utility. If the TrackPoint is disabled, select Automatic to enable it.
Power system checkout To 1. 2. 3. 4. 5. 6. 7. verify a symptom, do the following: Turn off the computer. Remove the battery pack. Connect the ac adapter. Check that power is supplied when you turn on the computer. Turn off the computer. Disconnect the ac adapter and install the charged battery pack. Check that the battery pack supplies power when you turn on the computer.
Checking operational charging To check whether the battery charges properly during operation, use a discharged battery pack or a battery pack that has less than 50% of the total power remaining when installed in the computer. Perform operational charging. If the battery status indicator or icon does not turn on, remove the battery pack and let it return to room temperature. Reinstall the battery pack. If the charge indicator or icon still does not turn on, replace the battery pack.
Checking the backup battery Do the following: 1. Power off the computer, and unplug the ac adapter from it. 2. Turn the computer upside down. 3. Remove the battery pack (see “1010 Battery pack” on page 87). 4. Remove the backup battery (see “1120 Backup battery” on page 107). 5. Measure the voltage of the backup battery. See the following figure. Red (+) Black (-) Wire Voltage (V dc) Red +2.5 to +3.2 Black Ground v If the voltage is correct, replace the system board.
54 ThinkPad T510, T510i, and W510 Hardware Maintenance Manual
Related service information This chapter presents following information: v “Restoring the factory contents by using Recovery Disc Set” v “Passwords” on page 56 v “Power management” on page 60 v “Symptom-to-FRU index” on page 62 Service Web site: When the latest maintenance diskette and the system program service diskette become available, they will be posted on http://www.lenovo.
Note: Recovery takes several hours. The length of time depends on the method you use. If you use recovery discs, recovery takes at least five hours. 1. Make the CD/DVD drive the first startup device in the startup sequence using the following procedure: a. Press and hold down the F1 key, and then turn on the computer. When the logo screen is displayed or if you hear repeating beeps, release the F1 key. The Setup Utility program opens. b. Use the arrow keys to select Startup → Boot. 2. 3. 4. 5. 6. 7. 8. 9.
Exception: If only an SVP is installed, the password prompt does not appear when the operating system is booted. Power-on password A power-on password (POP) protects the system from being powered on by an unauthorized person. The password must be entered before an operating system can be booted. For how to remove the POP, see “How to remove the power-on password.
After the POST ends, the password prompt does not appear. The POP has been removed. 5. Reinstall the backup battery and the battery pack. (B) If an SVP has been set and is known by the service technician: 1. Turn on the computer. 2. When the ThinkPad logo comes up, immediately press F1 to enter BIOS Setup Utility. For models supporting the Passphrase function, press F1 while the POP icon is appearing on the screen; then enter the POP. For the other models, enter the POP.
7. Type the current master HDP in the Enter Current Password field. then leave the Enter New Password field blank, and press Enter twice. 8. Press F10. 9. Select Yes in the Setup Configuration window. Both user HDP and master HDP will have been removed.
Power management To reduce power consumption, the computer has three power management modes: screen blank, sleep (standby in Windows XP), and hibernation. Screen blank mode If the time set on the “Turn off monitor” timer in the operating system expires, the LCD backlight turns off. To put the computer into screen blank mode, do as follows: 1. Press Fn+F3. A panel for selecting a power plan (in Windows XP, power scheme) appears. 2.
Also, in either of the following events, the computer automatically returns from sleep (standby) mode and resumes operation: v The ring indicator (RI) is signaled by a serial device or a PC Card device. v The time set on the resume timer elapses. Note: The computer does not accept any input immediately after it enters sleep (standby) mode. Wait a few seconds before taking any action to reenter operation mode.
Symptom-to-FRU index This section contains following information: v “Numeric error codes” v “Error messages” on page 66 v “Beep symptoms” on page 67 v “No-beep symptoms” on page 67 v “LCD-related symptoms” on page 68 v “Intermittent problems” on page 69 v “Undetermined problems” on page 69 The symptom-to-FRU index in this section lists symptoms and errors and their possible causes. The most likely cause is listed first, in boldface type.
Table 2. Numeric error codes (continued) Symptom or error FRU or action, in sequence 0187 EAIA data access error—The access to EEPROM is failed. System board. 0188 Invalid RFID Serialization Information Area. System board. 0189 System board. Invalid RFID configuration information area—The EEPROM checksum is not correct. 0190 Critical low-battery error 1. Charge the battery pack. 2. Battery pack. 0191 System Security—Invalid Remote Change requested. 1.
Table 2. Numeric error codes (continued) 64 Symptom or error FRU or action, in sequence 0251 System CMOS checksum bad— Default configuration used. 1. Charge the backup battery for more than 8 hours by connecting the ac adapter. 2. Replace the backup battery and run BIOS Setup Utility to reset the time and date. 0252 Password checksum bad—The password is cleared. Reset the password by running BIOS Setup Utility. 0260 System timer error. 1.
Table 2. Numeric error codes (continued) Symptom or error FRU or action, in sequence 1805 Unauthorized Wireless USB card is plugged in—Power off and remove the Wireless USB card. 1. Remove the Wireless USB card that you installed. 2. System board. 1820 More than one external fingerprint reader is attached. Power off and remove all but the reader that you set up within your main operating system. Remove all but the reader that you set up for the authentication.
Error messages Table 3. Error messages Symptom or error FRU or action, in sequence Device address conflict. 1. Load “Setup Defaults” in the BIOS Setup Utility. 2. Backup battery. 3. System board. Allocation error for device. 1. Load “Setup Defaults” in the BIOS Setup Utility. 2. Backup battery. 3. System board. Failing bits: nnnn. 1. DIMM. 2. System board. Invalid system configuration data. 1. DIMM. 2. System board. I/O device IRQ conflict. 1. Load “Setup Defaults” in the BIOS Setup Utility. 2.
Beep symptoms Table 4. Beep symptoms Symptom or error FRU or action, in sequence One beep and a blank, unreadable, or flashing LCD. 1. 2. 3. 4. One long and two short beeps, and a blank or unreadable LCD. 1. System board. 2. LCD assembly. 3. DIMM. Two short beeps with error codes. POST error. See “Numeric error codes” on page 62. Two short beeps and a blank screen. 1. System board. 2. DIMM. Three short beeps, pause, three more short beeps, and one short beep. 1. DIMM. 2.
LCD-related symptoms Important: The TFT LCD for the notebook computer contains many thin-film transistors (TFTs). The presence of a small number of dots that are missing, discolored, or always lighted is characteristic of TFT LCD technology, but excessive pixel problems can cause viewing concerns. If the LCD you are servicing has two or less visible defective pixels, it should not be considered faulty.
Intermittent problems Intermittent system hang problems can be due to a variety of causes that have nothing to do with a hardware defect, such as cosmic radiation, electrostatic discharge, or software errors. FRU replacement should be considered only when a problem recurs. When analyzing an intermittent problem, do the following: 1. Run the diagnostic test for the system board in loop mode at least 10 times. 2. If no error is detected, do not replace any FRUs. 3.
70 ThinkPad T510, T510i, and W510 Hardware Maintenance Manual
Installing and configuring RAID This chapter presents following information about attaching SATA devices and configuring RAID for the RAID-supported models in this product. Note: When the BIOS was formatted or the system board was replaced in the RAID-supported models, RAID is enabled by default. Important notices for setting RAID: Before you install and configure RAID, make sure of the current RAID setting on the computer you are servicing.
Creating RAID volumes This section describes how to use the Intel® Rapid Storage Technology option ROM Configuration Utility to create RAID volumes. To create RAID volumes, do as follows: 1. Turn on the computer. 2. During the startup, when a prompt to press Ctrl+I to enter the Configuration Utility is displayed on the screen, press and hold the Ctrl key, and press the I key. 3. The screen for Intel Rapid Storage Technology option ROM is displayed. Select “Create RAID Volume” and press Enter. 4.
Status indicators This chapter presents the system status indicators that show the status of the computer.
Table 7. Status indicators Indicator Meaning 1 Speaker mute Orange: The speaker is on mute. To set the speakers on mute or unmute, press the speaker mute button. 2 Microphone mute Orange: The microphone is on mute. None of the recording devices is available while the microphone mute is on by default. 3 Wireless LAN, Green: The wireless LAN feature (the IEEE 802.11 b/g Wireless WAN, standard, 802.11 a/b/g, or 802.
Table 7. Status indicators (continued) Indicator Meaning 8 Fingerprint reader status Green: Caps lock Green: 9 The fingerprint reader is ready to swipe. Blinking green: The fingerprint is being authenticated or has been authenticated. Blinking orange: The fingerprint could not be authenticated. Caps Lock mode is enabled. To enable or disable Caps Lock mode, press the Caps Lock key. 10 Sleep (standby Green: The computer is in sleep (standby) mode.
76 ThinkPad T510, T510i, and W510 Hardware Maintenance Manual
Fn key combinations The following table shows the function of each combination of Fn with a function key. Table 8. Fn key combinations Key combination Description Fn+F1 Reserved. Fn+F2 Lock the computer. Fn+F3 Select a power plan (in Windows XP, power scheme) that has been created by Power Manager, or adjust the power level by using the slider control. When you press this combination, a panel for selecting a power plan (power scheme) appears.
Table 8. Fn key combinations (continued) Key combination Description Fn+F7 Apply a presentation scheme directly, with no need to start Presentation Director. To disable this function and use the Fn+F7 key combination for switching a display output location, start Presentation Director, and change the settings. Note: If the computer is an Windows 7 model, it does not support presentation schemes, however the Fn+F7 combination might still be used to switch display output location.
Table 8. Fn key combinations (continued) Key combination Description Fn+F12 Put the computer into hibernation mode. To return to normal operation, press the power button for less than four seconds. Notes: To use this combination of the keys, ThinkPad PM device driver must have been installed on the computer. Though the screen fades out immediately after Fn+F12 are pressed, the computer does not enter the hibernation mode immediately.
80 ThinkPad T510, T510i, and W510 Hardware Maintenance Manual
FRU replacement notices This chapter presents notices related to removing and replacing parts. Read this chapter carefully before replacing any FRU. Screw notices Loose screws can cause a reliability problem. In the ThinkPad Notebook, this problem is addressed with special nylon-coated screws that have the following characteristics: v They maintain tight connections. v They do not easily come loose, even with shock or vibration. v They are harder to tighten. v Each one should be used only once.
Retaining serial numbers This section includes the following descriptions: v “Restoring the serial number of the system unit” v “Retaining the UUID” v “Reading or writing the ECA information” on page 83 Restoring the serial number of the system unit When the computer was manufactured, the EEPROM on the system board was loaded with the serial numbers of the system and all major components. These numbers need to remain the same throughout the life of the computer.
The algorithm that generates the number is designed to provide unique IDs until the year A.D. 3400. No two computers in the world have the same number. When you replace the system board, you must set the UUID on the new system board as follows: 1. Install the LENOVO ThinkPad Hardware Maintenance Diskette Version 1.76 or later, and restart the computer. 2. From the main menu, select 4. Assign UUID. A new UUID is created and written. If a valid UUID already exists, it is not overwritten.
84 ThinkPad T510, T510i, and W510 Hardware Maintenance Manual
Removing and replacing a FRU This chapter presents directions and drawings for use in removing and replacing a FRU. Be sure to observe the following general rules: 1. Do not try to service any computer unless you have been trained and certified. An untrained person runs the risk of damaging parts. 2. Before replacing any FRU, review “FRU replacement notices” on page 81. 3. Begin by removing any FRUs that have to be removed before the failing FRU. Any such FRUs are listed at the top of the page.
Before servicing ThinkPad T510, T510i, and W510 Table 9. Removal steps of SIM card Some models of the ThinkPad T510, T510i, and W510 you are servicing might have the SIM card that the customer has installed. If the computer you are servicing has the SIM card, remove it before you start the servicing. To remove the SIM card, you need to remove the battery pack first. (See “1010 Battery pack” on page 87.) After you finish the servicing, make sure that you insert the card back into the slot firmly.
1010 Battery pack Important notice for replacing a battery pack: ThinkVantage Toolbox (in Windows 7) and Lenovo System Toolbox (in Windows Vista and Windows XP) have an automatic battery diagnostic that determines if the battery pack is defective. A battery pack FRU should not be replaced unless this diagnostic shows that the battery is defective. The only exception to this is if the battery pack is physically damaged or a customer is reporting a possible safety issue.
1020 Serial Ultrabay Enhanced device or travel bezel For access, remove this FRU: v “1010 Battery pack” on page 87 Table 11. Removal steps of Serial Ultrabay Enhanced device or travel bezel Holding the bay lock latch in the unlocked position 1 , slide the bay eject latch 2 , and then pull out the Serial Ultrabay Enhanced device or the travel bezel in the direction shown by arrow 3 .
1030 DIMM slot cover For access, remove this FRU: v “1010 Battery pack” on page 87 Table 12. Removal steps of DIMM slot cover Note: Loosen the screws 1 , but do not remove them.
1040 DIMM (bottom slot) For access, remove these FRUs in order: v “1010 Battery pack” on page 87 v “1030 DIMM slot cover” on page 89 Table 13. Removal steps of DIMM (bottom slot) a b 1 2 1 Note: If only one DIMM is used on the computer you are servicing, the card must be installed in SLOT-0 ( a ), but not in SLOT-1 ( b ). When installing: Insert the notched end of the DIMM into the socket. Press the DIMM firmly, and pivot it until it snaps into the place.
1050 Hard disk drive slot cover, hard disk drive (HDD) and HDD rubber rails or Solid state drive (SSD) and storage converter For access, remove this FRU: v “1010 Battery pack” on page 87 Attention: v Do not drop the drive or apply any physical shock to it. The drive is sensitive to physical shock. Improper handling can cause damage and permanent loss of data. v Before removing the drive, have the user make a backup copy of all the information on it if possible.
Table 15. Removal steps of HDD and HDD rubber rails 4 4 Table 16. Removal steps of SSD and storage converter 4 5 When installing: Make sure that the SSD connector or HDD connector is attached firmly.
1060 Keyboard For access, remove these FRUs in order: v “1010 Battery pack” on page 87 v “1030 DIMM slot cover” on page 89 Table 17. Removal steps of keyboard 1 1 Step Screw (quantity) Color Torque 1 M2 × 14 mm, wafer-head, nylon-coated (2) Black 0.181 Nm (1.
Table 17. Removal steps of keyboard (continued) Push down the keyboard a little toward the arrow 2 until the front edge of the keyboard is detached from the keyboard bezel. 2 Lift the keyboard a little in the direction shown by arrow 3 , and then detach the connector 4 .
When installing the keyboard, do as follows: Table 18. Installation steps of keyboard 1. Attach the keyboard connector 1 . 1 2. Attach the keyboard so that the keyboard edges a are under the frame as shown in this figure.
Table 18. Installation steps of keyboard (continued) 3. Gently press the keys with your thumbs and try to slide the keyboard toward you. 4. Make sure that the front side of the keyboard ( b ) is housed firmly. b b b 5. Secure the keyboard by tightening the screws from the bottom side of the computer.
1070 DIMM (upper slot) For access, remove these FRUs in order: v “1010 Battery pack” on page 87 v “1030 DIMM slot cover” on page 89 v “1060 Keyboard” on page 93 Table 19. Removal steps of DIMM (upper slot) 1 2 1 Note: If only one DIMM is used on the computer you are servicing, the card must be installed in SLOT-0 ( a ), but not in SLOT-1 ( b ). a b When installing: Insert the notched end of the DIMM into the socket. Press the DIMM firmly, and pivot it until it snaps into the place.
1080 PCI Express Mini Card for wireless LAN For access, remove these FRUs in order: v “1010 Battery pack” on page 87 v “1030 DIMM slot cover” on page 89 v “1060 Keyboard” on page 93 Table 20. Removal steps of PCI Express Mini Card for wireless LAN In step 1 , unplug the jacks by using the removal tool antenna RF connector (P/N: 08K7159) or pick the connectors with your fingers and gently unplug them in direction of the arrow. Note: Some models might have only two antenna cables in step 1 .
Table 20. Removal steps of PCI Express Mini Card for wireless LAN (continued) 2 2 3 Step Screw (quantity) Color Torque 2 M2 × 3 mm, wafer-head, nylon-coated (2) Silver 0.181 Nm (1.
Table 20. Removal steps of PCI Express Mini Card for wireless LAN (continued) When installing: v In models with wireless LAN card that has two antenna connectors, plug the gray cable into the jack labeled MAIN or M, and the black cable into the jack labeled AUX or A on the card. If the computer you are servicing has three cables, put the white cable in the cable protection tube as shown in this figure.
0 PCI Express Mini Card for wireless WAN For access, remove these FRUs in order: v “1010 Battery pack” on page 87 v “1030 DIMM slot cover” on page 89 v “1060 Keyboard” on page 93 Table 21. Removal steps of PCI Express Mini Card for wireless WAN In step 1 , unplug the jacks by using the removal tool antenna RF connector (P/N: 08K7159) or pick the connectors with your fingers and gently unplug them in direction of the arrow.
Table 21. Removal steps of PCI Express Mini Card for wireless WAN (continued) 2 2 3 Step Screw (quantity) Color Torque 2 M2 × 3 mm, wafer-head, nylon-coated (2) Silver 0.181 Nm (1.85 kgfcm) 4 Note: Plug the orange cable into the jack labeled MAIN, and the blue cable into the jack labeled AUX on the card.
1100 Keyboard bezel assembly For access, remove these FRUs in order: v “1010 Battery pack” on page 87 v “1030 DIMM slot cover” on page 89 v “1060 Keyboard” on page 93 Attention: Before removing the keyboard bezel assembly, make sure that you have removed ExpressCard blank bezel or any card in the slot. Table 22. Removal steps of ExpressCard blank bezel or ExpressCard When you press the ExpressCard blank bezel or ExpressCard 1 , it pops out 2 .
Table 22. Removal steps of ExpressCard blank bezel or ExpressCard (continued) When installing: Make sure that the bezel or the card is correctly oriented as shown in this figure. Table 23. Removal steps of keyboard bezel assembly Note: The speaker assembly is attached to the keyboard bezel. 2 2 1 1 1 2 2 1 104 2 Step Screw (quantity) Color Torque 1 M2 × 4 mm, bind-head, nylon-coated (4) Black 0.181 Nm (1.85 kgfcm) 2 M2 × 14 mm, bind-head, nylon-coated (7) Black 0.181 Nm (1.
Table 23.
1110 Bluetooth daughter card (BDC-2.1) For access, remove these FRUs in order: v “1010 Battery pack” on page 87 v “1030 DIMM slot cover” on page 89 v “1060 Keyboard” on page 93 v “1100 Keyboard bezel assembly” on page 103 Table 24. Removal steps of BDC-2.1 1 2 Step Screw (quantity) Color Torque 1 M2 × 3 mm, wafer-head, nylon-coated (1) Silver 0.181 Nm (1.85 kgfcm) When installing: Make sure that the connector is attached firmly.
1120 Backup battery For access, remove these FRUs in order: v “1010 Battery pack” on page 87 v “1030 DIMM slot cover” on page 89 v “1060 Keyboard” on page 93 v “1100 Keyboard bezel assembly” on page 103 DANGER Use only the battery specified in the parts list for your computer. Any other battery could ignite or explode. Table 25. Removal steps of backup battery 2 1 When installing: Make sure that the battery connector is attached firmly.
1130 Smart Card or Contactless Smart Card or Smart Card dummy spacer For access, remove these FRUs in order: v “1010 Battery pack” on page 87 v “1030 DIMM slot cover” on page 89 v “1060 Keyboard” on page 93 v “1100 Keyboard bezel assembly” on page 103 Table 26. Removal steps of Smart Card 3 3 4 1 108 2 Step Screw (quantity) Color Torque 3 M2 × 3 mm, wafer-head, nylon-coated (4) Silver 0.181 Nm (1.
Table 26. Removal steps of Smart Card (continued) 5 6 5 Table 27. Removal steps of dummy card and Contactless Smart Card 5 3 3 4 1 2 Step Screw (quantity) Color Torque 3 M2 × 3 mm, wafer-head, nylon-coated (4) Silver 0.181 Nm (1.
Table 27. Removal steps of dummy card and Contactless Smart Card (continued) 6 7 6 Table 28. Removal steps of dummy card and spacer 3 1 1 2 110 Step Screw (quantity) Color Torque 1 M2 × 3 mm, wafer-head, nylon-coated (4) Silver 0.181 Nm (1.
1140 Speaker assembly For access, remove these FRUs in order: v “1010 Battery pack” on page 87 v “1030 DIMM slot cover” on page 89 v “1060 Keyboard” on page 93 v “1100 Keyboard bezel assembly” on page 103 Table 29. Removal steps of speaker assembly 2 1 1 3 2 1 1 Step Screw (quantity) Color Torque 1 M2 × 3 mm, wafer-head, nylon-coated (4) Silver 0.181 Nm (1.
Table 29. Removal steps of speaker assembly (continued) 5 4 5 4 4 5 5 5 4 When installing: Make sure that the speaker connector is attached firmly. Then route the cables and secure them properly as shown in the figure above.
1150 Thermal module For access, remove these FRUs in order: v “1010 Battery pack” on page 87 v “1030 DIMM slot cover” on page 89 v “1060 Keyboard” on page 93 v “1100 Keyboard bezel assembly” on page 103 v “1140 Speaker assembly” on page 111 Table 30. Removal steps of thermal module 1 2 When installing: Make sure that the connectors are attached firmly. Note: Loosen the screws 4a to 4d in order, but do not remove them. Some models do not have screws 5 . For those models, skip the step 5 .
Table 30. Removal steps of thermal module (continued) 6 When installing: Before you attach the fan assembly to the computer, apply thermal grease, at an amount of 0.2 grams, on the parts marked a as in the following figures. Either too much or too less application of grease can cause a thermal problem due to imperfect contact with a component. For the new CPU thermal device/fan, you need to peel the thin film off from the rubbers marked b .
Table 30.
1160 CPU For access, remove these FRUs in order: v “1010 Battery pack” on page 87 v “1030 DIMM slot cover” on page 89 v “1060 Keyboard” on page 93 v “1100 Keyboard bezel assembly” on page 103 v “1140 Speaker assembly” on page 111 v “1150 Thermal module” on page 113 Attention: CPU is extremely sensitive. When you service the CPU, avoid any kind of rough handling. Table 31. Removal steps of CPU Rotate the head of the screw in the direction shown by arrow 1 to release the lock; then remove the CPU 2 .
1170 LCD unit For access, remove these FRUs in order: v “1010 Battery pack” on page 87 v “1030 DIMM slot cover” on page 89 v “1050 Hard disk drive slot cover, hard disk drive (HDD) and HDD rubber rails or Solid state drive (SSD) and storage converter” on page 91 v “1060 Keyboard” on page 93 v “1080 PCI Express Mini Card for wireless LAN” on page 98 v “1090 PCI Express Mini Card for wireless WAN” on page 101 v “1100 Keyboard bezel assembly” on page 103 Table 32.
Table 32. Removal steps of LCD unit (continued) 3 3 118 Step Screw (quantity) 3 M2.5 × 6 mm, wafer-head, nylon-coated (2) Black ThinkPad T510, T510i, and W510 Hardware Maintenance Manual Color Torque 0.392 Nm (4.
Table 32. Removal steps of LCD unit (continued) 8 7 7 6 4 4 5 5 4 Step Screw (quantity) Color Torque 7 M2 × 4 mm, wafer-head, nylon-coated (2) Black 0.181 Nm (1.85 kgfcm) When installing: v Make sure that you attach the LCD connector firmly. v Make sure that you route the cables firmly and tape up in the proper positions as shown in this figure. v When you route the cables, make sure that they are not subjected to any tension.
Table 32.
1180 Base cover assembly For access, remove these FRUs in order: v “1010 Battery pack” on page 87 v “1020 Serial Ultrabay Enhanced device or travel bezel” on page 88 v “1030 DIMM slot cover” on page 89 v “1050 Hard disk drive slot cover, hard disk drive (HDD) and HDD rubber rails or Solid state drive (SSD) and storage converter” on page 91 v “1060 Keyboard” on page 93 v “1080 PCI Express Mini Card for wireless LAN” on page 98 v “1090 PCI Express Mini Card for wireless WAN” on page 101 v “1100 Keyboard bezel
Table 33.
Note: Applying labels to the base cover The new base cover FRU is shipped with a kit containing labels of several kinds. When you replace the base cover, you need to apply the following labels: 13 FCC label 14 Homologation label 15 Serial number label Following labels need to be peeled off from the old base cover, and need to be put on the new base cover.
1190 I/O sub card For access, remove these FRUs in order: v “1010 Battery pack” on page 87 v “1020 Serial Ultrabay Enhanced device or travel bezel” on page 88 v “1030 DIMM slot cover” on page 89 v “1050 Hard disk drive slot cover, hard disk drive (HDD) and HDD rubber rails or Solid state drive (SSD) and storage converter” on page 91 v “1060 Keyboard” on page 93 v “1080 PCI Express Mini Card for wireless LAN” on page 98 v “1090 PCI Express Mini Card for wireless WAN” on page 101 v “1100 Keyboard bezel assemb
1200 System board assembly and magnesium structure frame For access, remove these FRUs in order: v “1010 Battery pack” on page 87 v “1020 Serial Ultrabay Enhanced device or travel bezel” on page 88 v “1030 DIMM slot cover” on page 89 v “1040 DIMM (bottom slot)” on page 90 v “1050 Hard disk drive slot cover, hard disk drive (HDD) and HDD rubber rails or Solid state drive (SSD) and storage converter” on page 91 v “1060 Keyboard” on page 93 v “1070 DIMM (upper slot)” on page 97 v “1080 PCI Express Mini Card fo
Important notices for handling the system board: When handling the system board, bear the following in mind. v The system board has an accelerometer, which can be broken by applying several thousands of G-forces. Note: Dropping a system board from a height of as little as 6 inches so that it falls flat on a hard bench can subject the accelerometer to as much as 6,000 G’s of shock. v Be careful not to drop the system board on a bench top that has a hard surface, such as metal, wood, or composite.
Table 35.
Table 36. Removal steps of system board and magnesium structure frame 2 3 2 2 1 1 Step Screw (quantity) Color Torque 1 Hex stud, nylon-coated (2) Silver 0.392 Nm (4.0 kgfcm) 2 M2 × 7 mm, wafer-head, nylon-coated (3) Silver 0.181 Nm (1.85 kgfcm) When installing: When you replace the system board, attach thermal rubbers as shown in this figure. Depend on the models you are servicing, the number of thermal rubbers are different.
2010 LCD bezel assembly For access, remove this FRU: v “1010 Battery pack” on page 87 Table 37. Removal steps of LCD bezel assembly 1 1 1 Step 1 Screw cap Screw (quantity) M2.5 × 6 mm, wafer-head, nylon-coated (3) Color Torque Black 0.392 Nm (4.0 kgfcm) 2 2 2 2 2 2 2 2 3 When installing: Make sure that all the latches are attached firmly.
2020 LED sub card For access, remove these FRUs in order: v “1010 Battery pack” on page 87 v “2010 LCD bezel assembly” on page 129 Table 38. Removal steps of LED sub card Note: Some models do not have connector 1a . 2 1a 1 When installing: Make sure that the connectors are attached firmly and the card is installed as shown in this figure.
2030 Integrated camera For access, remove these FRUs in order: v “1010 Battery pack” on page 87 v “2010 LCD bezel assembly” on page 129 Table 39. Removal steps of integrated camera 1 3 2 Step Screw (quantity) Color Torque 1 M2 × 3 mm, wafer-head, nylon-coated (1) Silver 0.181 Nm (1.85 kgfcm) When installing: Make sure that the connector of the integrated camera is attached firmly.
2040 LCD cable, camera cable, LCD panel, and hinges For access, remove these FRUs in order: v “1010 Battery pack” on page 87 v “1030 DIMM slot cover” on page 89 v “1050 Hard disk drive slot cover, hard disk drive (HDD) and HDD rubber rails or Solid state drive (SSD) and storage converter” on page 91 v “1060 Keyboard” on page 93 v “1080 PCI Express Mini Card for wireless LAN” on page 98 v “1090 PCI Express Mini Card for wireless WAN” on page 101 v “1100 Keyboard bezel assembly” on page 103 v “1170 LCD unit”
Table 40. Removal steps of LCD cable, camera cable, LCD panel, and hinges (continued) 2 2 2 2 Step Screw (quantity) Color 2 M2.5 × 6 mm, wafer-head, nylon-coated (4) Black Torque 0.392 Nm (4.0 kgfcm) When installing: When attaching the LCD panel to the cover, press the left and right edges covered with metal gently with your fingers. DO NOT press the surface of the panel or apply any excessive force to the panel.
Table 40. Removal steps of LCD cable, camera cable, LCD panel, and hinges (continued) 6 7 8 When installing: Make sure that the LCD cable connector is attached firmly. 9 10 9 9 10 9 134 Step Screw (quantity) Color Torque 9 M2 × 3 mm, wafer-head, nylon-coated (4) Silver 0.181 Nm (1.
2050 Antenna kit and LCD rear cover assembly For access, remove these FRUs in order: v “1010 Battery pack” on page 87 v “1030 DIMM slot cover” on page 89 v “1050 Hard disk drive slot cover, hard disk drive (HDD) and HDD rubber rails or Solid state drive (SSD) and storage converter” on page 91 v “1060 Keyboard” on page 93 v “1080 PCI Express Mini Card for wireless LAN” on page 98 v “1090 PCI Express Mini Card for wireless WAN” on page 101 v “1100 Keyboard bezel assembly” on page 103 v “1170 LCD unit” on page
Table 41. Removal steps of antenna kit and LCD rear cover assembly (continued) Cable routing: When you install the antenna kit, route the cables as shown in the figures below. As you route the cables, make sure that they are not subjected to any tension. Tension could cause the cables to be damaged by the cable guides, or a wire to be broken.
Locations This chapter presents the location of ThinkPad T510, T510i, and W510 features and hardware. Front view 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 © Copyright Lenovo 2009 Status indicators Note: For the description of each indicator, see “Status indicators” on page 73.
1 2 3 4 2 21 8 20 18 5 17 6 16 19 7 15 8 14 9 13 10 12 138 ThinkPad T510, T510i, and W510 Hardware Maintenance Manual 11
Rear view 1 2 3 4 5 6 7 8 9 10 11 Status indicators Note: For the description of each indicator, see “Status indicators” on page 73.
Bottom view 1 2 3 4 5 6 7 8 Battery pack Battery pack latch Docking connector Solid state drive (SSD) or hard disk drive (HDD) slot DIMM slot (bottom) LCD cover latch Serial Ultrabay Enhanced lock latch Serial Ultrabay Enhanced eject latch 1 8 7 2 3 6 5 4 140 ThinkPad T510, T510i, and W510 Hardware Maintenance Manual
Parts list This chapter contains following lists of the service parts. v “Overall” on page 142 v “LCD FRUs” on page 170 v “Keyboard” on page 186 v “Miscellaneous parts” on page 187 v “AC adapters” on page 189 v “Power cords” on page 190 v “Recovery discs” on page 191 v “Common service tools” on page 200 Notes: v Each FRU is available for all types or models, unless specific types or models are specified.
Overall 23 22 1 2 21 d a 3 c b 20 19 4 5 18 17 6 16 15 7 8 14 13 9 10 7 12 11 142 ThinkPad T510, T510i, and W510 Hardware Maintenance Manual
Table 42. Parts list—Overall No. FRU (Overall) FRU no. CRU ID a - d See “Miscellaneous parts” on page 187. 1 LCD unit (see “LCD FRUs” on page 170.
Table 42. Parts list—Overall (continued) No. FRU (Overall) FRU no.
Table 42. Parts list—Overall (continued) No. FRU (Overall) FRU no.
Table 42. Parts list—Overall (continued) No. FRU (Overall) FRU no.
Table 42. Parts list—Overall (continued) No. FRU (Overall) FRU no.
Table 42. Parts list—Overall (continued) No. 6 148 FRU (Overall) FRU no.
Table 42. Parts list—Overall (continued) No. FRU (Overall) FRU no.
Table 42. Parts list—Overall (continued) No. FRU (Overall) FRU no.
Table 42. Parts list—Overall (continued) No. FRU (Overall) FRU no.
Table 42. Parts list—Overall (continued) No. FRU (Overall) FRU no.
Table 42. Parts list—Overall (continued) No. FRU (Overall) FRU no.
Table 42. Parts list—Overall (continued) No. FRU (Overall) FRU no.
Table 42. Parts list—Overall (continued) No. FRU (Overall) FRU no.
Table 42. Parts list—Overall (continued) No. FRU (Overall) FRU no.
Table 42. Parts list—Overall (continued) No. FRU (Overall) FRU no.
Table 42. Parts list—Overall (continued) No. FRU (Overall) FRU no.
Table 42. Parts list—Overall (continued) No. FRU (Overall) FRU no.
Table 42. Parts list—Overall (continued) No. FRU (Overall) FRU no.
Table 42. Parts list—Overall (continued) No. FRU (Overall) FRU no.
Table 42. Parts list—Overall (continued) No. FRU (Overall) FRU no.
Table 42. Parts list—Overall (continued) No. FRU (Overall) FRU no.
Table 42. Parts list—Overall (continued) No. FRU (Overall) FRU no.
Table 42. Parts list—Overall (continued) No. FRU (Overall) FRU no.
Table 42. Parts list—Overall (continued) No. FRU (Overall) FRU no. CRU ID 16 CPU assembly, Intel Core i5-430M Processor (2.26 GHz) v 4313-CTO, 5Fx v 4314-CTO, 5Gx, 5Hx, 5Jx, 5Kx, 5Nx, 5Px, 5Ux, 5Vx, 5Wx, 5Xx, 62x, 64x, 67x, 68x, 6Ax, 6Cx, 6Fx, 6Jx, 6Ux, 6Vx v 4339-CTO v 4349-CTO v 4384-CTO v 4484-CTO v 4873-CTO 63Y2176 N 16 60Y5731 CPU assembly, Intel Core i5-520M Processor (2.
Table 42. Parts list—Overall (continued) No. FRU (Overall) FRU no. CRU ID 16 CPU assembly, Intel Core i7-820QM Processor (1.73 GHz) v 4318-CTO v 4319-CTO, 27x, 29x, 2Cx, 2Fx, 2Lx, 2Nx, 2Px, 2Qx, 2Rx, 2Wx, 2Yx, 32x, 33x, 34x, 37x, 38x, 39x, 3Ax, 3Bx, 3Gx, 3Jx, 3Lx, 3Nx, 3Qx, 3Sx, 3Ux, 3Wx, 3Yx, 45x, 47x v 4387-CTO v 4389-CTO, 2Bx, 2Cx, 2Hx, 2Jx, 2Nx, 2Tx, 2Zx, 35x, 37x, 39x, 3Bx, 3Ex, 3Fx v 4391-CTO v 4875-CTO v 4876-CTO 63Y2001 N 16 CPU assembly, Intel Core i7-920XM Processor (2.
Table 42. Parts list—Overall (continued) No. FRU (Overall) FRU no.
Table 42. Parts list—Overall (continued) No. FRU (Overall) FRU no.
LCD FRUs In ThinkPad T510, T510i, and W510, there are following types of LCDs. v 15.6-inch High Definition (HD) LED-backlight LCD (Table 43 on page 171) v 15.6-inch HD+ LED-backlight LCD (Table 44 on page 176) v 15.6-inch Full High Definition (FHD) RG-ph LED-backlight LCD (Table 45 on page 181) v 15.
Table 43. Parts list—15.6-inch HD LED-backlight LCD No. FRU (15.6-inch HD LED-backlight LCD) FRU no.
Table 43. Parts list—15.6-inch HD LED-backlight LCD (continued) No. FRU (15.6-inch HD LED-backlight LCD) FRU no.
Table 43. Parts list—15.6-inch HD LED-backlight LCD (continued) No. FRU (15.6-inch HD LED-backlight LCD) FRU no.
Table 43. Parts list—15.6-inch HD LED-backlight LCD (continued) No. FRU (15.6-inch HD LED-backlight LCD) FRU no. CRU ID 10 LCD module, 15.
Table 43. Parts list—15.6-inch HD LED-backlight LCD (continued) No. 10 FRU (15.6-inch HD LED-backlight LCD) FRU no. CRU ID LCD module, 15.
Table 44. Parts list—15.6-inch HD+ LED-backlight LCD No. FRU (15.6-inch HD+ LED-backlight LCD) FRU no.
Table 44. Parts list—15.6-inch HD+ LED-backlight LCD (continued) No. FRU (15.6-inch HD+ LED-backlight LCD) FRU no.
Table 44. Parts list—15.6-inch HD+ LED-backlight LCD (continued) No. FRU (15.6-inch HD+ LED-backlight LCD) FRU no.
Table 44. Parts list—15.6-inch HD+ LED-backlight LCD (continued) No. FRU (15.6-inch HD+ LED-backlight LCD) FRU no.
Table 44. Parts list—15.6-inch HD+ LED-backlight LCD (continued) No. 10 180 FRU (15.6-inch HD+ LED-backlight LCD) FRU no. 42T0763 LCD module, 15.
Table 45. Parts list—15.6-inch FHD LED-backlight LCD No. FRU (15.6-inch FHD LED-backlight LCD) FRU no.
Table 45. Parts list—15.6-inch FHD LED-backlight LCD (continued) No. 3 3 FRU (15.6-inch FHD LED-backlight LCD) FRU no.
Table 45. Parts list—15.6-inch FHD LED-backlight LCD (continued) No. FRU (15.6-inch FHD LED-backlight LCD) FRU no.
Table 46. Parts list—15.6-inch FHD LED-backlight LCD with Multi touch panel No. FRU (15.6-inch FHD LED-backlight LCD with Multi touch panel) FRU no. CRU ID 1 LCD bezel assembly (touch panel) v 4318-CTO v 4319-CTO, 27x, 2Dx, 2Ux, 2Xx, 2Zx, 3Dx v 4387-CTO v 4389-CTO, 2Cx, 2Hx, 2Mx, 32x, 36x v 4391-CTO v 4875-CTO v 4876-CTO 60Y5483 N 2 Integrated camera (2.
Table 46. Parts list—15.6-inch FHD LED-backlight LCD with Multi touch panel (continued) No. 10 FRU (15.6-inch FHD LED-backlight LCD with Multi touch panel) FRU no. CRU ID LCD module, 15.
Keyboard Table 47. Parts list—Keyboard Language FRU no.
Miscellaneous parts Table 48. Parts list—Miscellaneous parts FRU FRU no. CRU ID Screw kit: v M2 × 3 mm (silver), small head (20) v M2 × 4 mm (black), wafer head (20) v M2 × 7 mm (black), wafer head (40) v M2 × 14 mm (black), wafer head (40) v M2.
Table 48. Parts list—Miscellaneous parts (continued) FRU FRU no.
AC adapters Table 49. Parts list—2-pin ac adapters FRU FRU no.
Power cords A ThinkPad power cord for a specific country or region is usually available only in that country or region: Table 52. Parts list—2-pin power cords Region P/N CRU ID Argentina v models -CTO, xxY 42T5020 42T5105 Brazil v models -CTO, xxP 42T5180 42T5183 Canada, U.S. v models -CTO, xxF, xxL, xxS, xxU 42T5008 42T5093 Japan v models -CTO, xxE, xxJ 42T5014 42T5099 * Table 53.
Recovery discs Windows XP Professional (32 bit) DVDs Windows XP Professional (32 bit) is preinstalled as the operating system in the following models: v 4313-CTO, 5Fx v 4314-CTO, 2Dx, 2Ex, 2Hx, 49x, 4Ax, 4Dx, 4Ex, 4Hx, 4Jx, 4Mx, 4Nx, 4Rx, 4Sx, 4Vx, 4Wx, 4Zx, 52x, 55x, 56x, 59x, 5Ax, 5Gx, 5Hx, 5Lx, 5Mx v 4318-CTO v 4319-CTO, 3Px, 3Qx, 3Rx, 3Sx, 3Tx, 3Ux, 3Vx, 3Wx v 4339-CTO v 4349-CTO, 4Cx, 4Ex, 4Fx, 4Gx, E4x v 4384-CTO, 44x, 45x, 46x, 47x, 4Bx v 4387-CTO v 4389-CTO, 2Dx v 4391-CTO, 23x v 4484-CTO v 4873-CTO
Windows Vista Business (32 bit) DVDs Windows Vista Business (32 bit) is preinstalled as the operating system in the following models: v 4313-CTO v 4314-CTO v 4318-CTO v 4319-CTO v 4339-CTO v 4349-CTO v 4384-CTO v 4387-CTO v 4389-CTO v 4391-CTO v 4484-CTO v 4873-CTO v 4875-CTO v 4876-CTO Table 55.
Windows 7 Home Basic (32 bit) DVDs Windows 7 Home Basic (32 bit) is preinstalled as the operating system in the following models: v 4313-CTO, 24x, 25x, 26x, 28x, 29x, 2Bx, 5Dx, 5Ex v 4314-CTO, 2Cx, 5Nx, 5Px, 66x, 68x, 6Ax v 4318-CTO v 4319-CTO v 4339-CTO, 27x, 28x, 29x, 2Bx, 2Cx, 2Dx v 4349-CTO v 4384-CTO v 4387-CTO v 4389-CTO v 4391-CTO v 4484-CTO v 4873-CTO v 4875-CTO v 4876-CTO Table 56.
Windows 7 Home Premium (32 bit) DVDs Windows 7 Home Premium (32 bit) is preinstalled as the operating system in the following models: v 4313-CTO v 4314-CTO, 36x, 37x, 38x, 3Xx, 3Yx, 3Zx, 63x, 65x, 6Kx, 6Lx, 6Mx, 6Nx v 4318-CTO v 4319-CTO v 4339-CTO v 4349-CTO, 2Vx, 2Wx, 2Xx, 3Nx, 3Px, 3Qx v 4384-CTO v 4387-CTO v 4389-CTO v 4391-CTO v 4484-CTO v 4873-CTO v 4875-CTO v 4876-CTO Table 57.
Windows 7 Home Premium (64 bit) DVDs Windows 7 Home Premium (64 bit) is preinstalled as the operating system in the following models: v 4313-CTO v 4314-CTO v 4318-CTO v 4319-CTO v 4339-CTO v 4349-CTO v 4384-CTO v 4387-CTO v 4389-CTO v 4391-CTO v 4484-CTO v 4873-CTO v 4875-CTO v 4876-CTO Table 58.
Windows 7 Professional (32 bit) DVDs Windows 7 Professional (32 bit) is preinstalled as the operating system in the following models: v 4313-CTO, 22x, 23x, 27x v 4314-CTO, 2Fx, 2Gx, 2Jx, 2Kx, 2Mx, 2Rx, 2Sx, 2Tx, 2Vx, 33x, 34x, 35x, 39x, 3Ax, 3Bx, 3Cx, 3Dx, 3Ex, 3Fx, 3Gx, 3Hx, 3Jx, 3Kx, 3Lx, 3Mx, 3Nx, 3Px, 3Qx, 3Rx, 3Sx, 3Tx, 3Ux, 3Vx, 3Wx, 42x, 43x, 44x, 45x, 46x, 47x, 48x, 4Bx, 4Cx, 4Fx, 4Gx, 4Kx, 4Lx, 4Px, 4Qx, 4Tx, 4Ux, 4Xx, 4Yx, 53x, 54x, 57x, 58x, 5Bx, 5Cx, 5Jx, 5Kx, 5Qx, 5Rx, 5Sx, 5Tx, 5Ux, 5Vx, 5Wx,
Table 59.
Windows 7 Professional (64 bit) DVDs Windows 7 Professional (64 bit) is preinstalled as the operating system in the following models: v 4313-CTO v 4314-CTO, 2Lx, 2Nx, 2Px, 2Qx, 2Ux, 2Xx, 2Zx, 32x, 5Xx, 5Yx, 5Zx, 62x, 64x, 6Ex, 6Fx, 6Gx, 6Tx, 6Ux, 6Vx v 4318-CTO v 4319-CTO, 24x, 25x, 27x, 29x, 2Cx, 2Dx, 2Ex, 2Rx, 2Ux, 2Yx, 2Zx, 33x, 3Bx, 3Dx, 3Yx v 4339-CTO v 4349-CTO, 2Mx, 2Px, 2Qx, 2Rx, 38x, 39x, 3Ax, 4Hx v 4384-CTO v 4387-CTO v 4389-CTO, 22x, 24x, 25x, 2Ax, 2Bx, 2Fx, 2Gx, 2Hx, 2Jx, 2Kx, 2Lx, 2Mx, 2Ux, 33x
Table 60.
Common service tools Table 61. Parts list—Common service tools Tool P/N Screwdriver kit 95F3598 1/4″ drive spinner handle 1650840 1/4″ Sq. to 1/4″ hex torx adapter 93F2838 TR7-TR-10 tamper resistant torx bits 00P6967 Removal tool antenna RF connector 08K7159 USB 2.
Notices Lenovo may not offer the products, services, or features discussed in this document in all countries. Consult your local Lenovo representative for information on the products and services currently available in your area. Any reference to a Lenovo product, program, or service is not intended to state or imply that only that Lenovo product, program, or service may be used.
vary significantly. Some measurements may have been made on development-level systems and there is no guarantee that these measurements will be the same on generally available systems. Furthermore, some measurements may have been estimated through extrapolation. Actual results may vary. Users of this document should verify the applicable data for their specific environment.
Part Number: 63Y0536 (1P) P/N: 63Y0536
