DANGER To avoid shock hazard: • Do not remove the covers. • Do not operate this product unless the stand is attached. • Do not connect or disconnect this product during an electrical storm. • The power cord plug must be connected to a properly wired and grounded power outlet. • Any equipment to which this product will be attached must also be connected to properlywired and grounded power outlets. • To isolate the monitor from the electrical supply, you must remove the plug from the power outlet.
GEVAAR Ga als volgt te werk om het gevaar van een elektrische schok te voorkomen: • Verwijder in geen enkel geval de kap. • Stel dit produkt alleen in werking als de voet is bevestigd. • Sluit dit apparaat niet aan op, of verbreek de aansluiting van dit apparaat niet van een contactdoos tijdens onweer. • Het netsnoer moet worden aangesloten op een geaarde contactdoos met correcte bedrading.
PERIGO Para evitar o perigo de choques eléctricos: • Não retire as coberturas. • Não utilize este produto antes de montar a base. • Não ligue nem desligue este produto durante uma tempestade eléctrica. • O cabo de alimentação deve ser ligado a uma tomada eléctrica devidamente ligada à terra. • Qualquer equipamento ligado a este produto deve estar ligado a tomadas eléctricas devidamente ligadas à terra.
ARNING - LIVSFARA För att undvika risk för elektriska stötar måste du tänka på följande: • Ta inte bort några skyddskåpor. • Använd inte den här produkten innan du har satt fast stativet. • Anslut inte produkten till ett eluttag under åskväder. Koppla inte heller ur produkten från ett eluttag under åskväder. • Strömkabeln måste anslutas till ett felfritt och jordat uttag. • All utrustning som den här produkten kopplas till måste också anslutas till felfria och jordade uttag.
• Bu cihaz7 elektriksel f7rt7na s7ras7nda prize takmay7n7z veya prizden ç7karmay7 n7z. • Elektrik kablosunun fiti, elektrik ve toprak ba5lant7lar7 usulüne uygun olarak yap7lm7t bir prize tak7lmal7d7r. • Bu cihazyn ba5lanaca5 7 di5er tüm cihazlar da elektrik ve toprak ba5lant7lar7 usulüne uygun olarak yap7lm7t prize tak7lm7t olmal7d7r. • Monitörün elektrikle ba5lant7s7n7 kesmek için fitini prizden çekmeniz gereklidir. Priz, kolayca eritilebilecek bir yerde olmal7d7r.
위험 전기 충격을 피하려면, • 제품의 덮개를 제거하지 마십시오. • 스탠드가 부착되어 있지 않으면 이 제품을 작동시키지 마십시오. • 뇌우를 동반할 때는 제품을 연결하거나 분리하지 마십시오. • 전원 코드를 올바르게 배선 및 접지된 콘센트에 연결해야 합니다. • 이 제품에 연결할 모든 장비는 올바르게 배선 및 접지된 콘센트에 연결되어 있어야합니다. • 모니터를 전기 공급 장치에서 분리시키려면, 콘센트에서 플러그를 제거해야 합니다. 콘센트는 접근하기 쉬운 곳에 있어야 합니다. 취급: • 저희 컬러 모니터는 무거우므로 주의해서 다루십시오. IBM은 모니터의 무 게가 18Kg 이상일 때 두사람이 움직이거나 들어올릴 것을 권장합니다.
3These user’s setup instructions cover typical user environments. The on-screen messages may differ depending on the level of your hardware and software. In some cases you may need to vary the setup procedures. For more information, refer to your computer or operating system manuals or consult your system administrator or dealer. Ces instructions de configuration d’exploitation s’appliquent aux environnements d’utilisation types.
First Edition (May / 2001) This publication could contain technical inaccuracies or typographical errors. Changes are made periodically to the information herein; these changes will be made in later editions. IBM may make improvements and/or changes in the product(s) and/or program(s) at any time. It is possible that this publication may contain reference to, or information about, IBM products (machines and programs), programming, or services that are not announced in your country.
Setup............................................................................................................................2 Hardware Requirements ......................................................................................2 Handling Instructions ...........................................................................................2 Workplace preparation .........................................................................................2 Working Practices .........................
Setup Hardware Requirements This monitor requires a computer with a suitable on-board sub-system or Video Adapter card that can support XGA 1024 x 768, SVGA 800 x 600, or VGA 640 x 480 at 60Hz. Handling Instructions Do not support the monitor within the screen area. The Liquid Crystal Display is glass and can be damaged by rough handling or excessive pressure. 1. Lift the monitor by placing both hands under the lower part of the cover.
ENGLISH Workplace Preparation i This section gives advice on what you should consider before you set up your monitor. Height The monitor should be positioned so that the top of the screen is slightly below your eye level when you sit at your workstation. Orientation - Choose a position that gives the least reflection from lights and windows, usually at a right angle to any windows. - Positon the monitor directly in front of you so that you do not have to twist your body to use it.
Connecting your Monitor 1. Turn off your computer and all attached devices. Be sure to read the ‘Safety Information’ at the front of this User Guide before carrying out this procedure. 2. Connect the monitor signal cable to the Video output of your computer and tighten the thumscrews. Ensure that the connectors align. Do not force the connectors as this may bend the pins.
ENGLISH 038F/En Adjusting the Monitor Position Viewing Angle You can tilt the screen backward and forward as shown below(figure A). Rotate You can rotate the screen leftward and rightward as shown below(figure A). Height You can adjust height of the screen(figure B). Before adjusting your monitor for the first time, remove the locking clip on rear of the stand. Carefully put down and hold the screen of monitor and then squeeze at arrows shown to remove(figure C).
Configuring your Monitor Setup Diskette for Microsoft®Windows®95 or Microsoft®Windows®98 This section must be completed before continuing with the Microsoft Windows95 or Microsoft Windows98 Auto Setup on page 8. i On LCD monitors, unlike CRTs, a faster refresh rate does not improve display quality. IBM recommends using either 1024 x 768 at a refresh rate of 60Hz or 640 x 480 at a refresh rate of 60Hz.
ENGLISH Setup Diskette for Microsoft®Windows®2000 Professional This section must be completed before continuing with the Microsoft Windows2000 Auto Setup on page 8. i On LCD monitors, unlike CRTs, a faster refresh rate does not improve display quality. IBM recommends using either 1024 x 768 at a refresh rate of 60Hz or 640 x 480 at a refresh rate of 60Hz. To use the Plug and Play feature in Windows 2000, files should be loaded from the IBM Monitor Installation diskette. 1.
Auto Setup Auto Setup Before carrying out this section, it is very important that The Setup Diskette for Windows 95 or Windows 98 has been run.(see page6) i The Setup Utility included on the setup diskette is for displaying dot patterns. They do not replace or modify the display driver. i The Auto Setup instructions require the monitor to be warmed up for 15 minutes. This is not required for normal operation. i By pressing the and keys simultaneously allows direct access to the auto set-up controls.
ENGLISH Auto Setup for DOS i If the monitor is in standby mode (STANDBY ON), it may automatically turn off while you are waiting for it to warm up. If this happens, switch off the monitor and switch it on again after a few seconds. 1. Turn on the monitor first; then the computer. i 2. Wait approximately 15 minutes, until the monitor warms up. 3. Insert the diskette labelled ‘IBM Monitor Installation Disk’ into the diskette drive. 4. Display the command prompt screen of the DOS full-screen display. 5.
Auto Setup for Microsoft®Windows®3.1, Windows®95 or Microsoft®Windows®2000 i If the monitor is in standby mode (STANDBY ON), it may automatically turn off while you are waiting for it to warm up. 1. Turn on the monitor first; then the computer. If the message CHECK SIGNAL CABLE is displayed, or if nothing is displayed check: • that the video interface cable is not connected properly. • the correct video adapter card is not installed. 2. Wait approximately 15 minutes, until the monitor warms up. 3.
ENGLISH 10. Press the ESC key to return to Windows. You have completed the monitor setup for Windows. If you use other operating systems, perform the appropriate AUTO SETUP for those systems, also: see Auto Setup for DOS on page 9.
Manual Setup Normally, you can complete the setup procedure using AUTO SETUP, however, if your screen image is still distorted after you perform AUTO SETUP or the setup diskette does not run on your system, perform MANUAL SETUP. i If the monitor is in standby mode (STANDBY ON), it might automatically turn off while you are waiting for it to warm up. 1. Have your monitor turned on for about 15 minutes, until the monitor warms up. 2. Display the image you most frequently use on the screen. 3.
User controls User control features Icon Direct Access Function Function Using Menu Controls None 1. Exits from menus, sub menus 2. Exits from OSD 1. Brings up Brightness control Moves the cursor to highlight icons or make adjustments. OSD 2. Left and Right arrows pressed together bring up auto setup i The image is already optimized for many display modes, however the user controls can be used to adjust the image to your liking.
CONTROLS LOCK / UNLOCK This feature allows you to secure the current control settings, while allowing the user to adjust Brightness, Contrast and initiate Auto Setup, so that they cannot be inadvertently changed. Push and hold the enter button[ ] for 10 seconds; the message “Controls Locked” appears. You can unlock the OSD controls at any time by pushing the enter button[ ] for 10 seconds; the message “Controls Unlocked” will appear.
ENGLISH On-screen display (OSD) controls i The LCD monitor needs time to become thermally stable the first time you turn it on each day. Thus, to achieve more accurate adjustments for parameters, allow the LCD monitor to warm up (be On) for at least 15 minutes before making any screen adjustment. The settings adjustable with the user controls are viewed through the On Screen Display (OSD). Press the enter button [ ] to display the main OSD menu.
OSD Icon Description If manual is selected, the user will go to the manual adjustment screen. Sub-menu(s) Manual SETUP • Fine • Coarse Select the Color Mode you find most comfortable and then fine tune the colors using the User Color Mode menu, if necessary. COLOR MODE COLOR Controls and Adjustments To adjust the focus of the display. This item allows you to remove any horizontal noise and clear or sharpen the image of characters. Fine adjustments should be can done after adjusting the Coarse .
ENGLISH OSD Icon RESET Description Sub-menu(S) Controls and Adjustments Reset should return all available functions • YES (apart from language which should not change unless adjusted via the • NO LANGUAGE menu) fo their factory presets. Moves the screen left and right . It is not availible when the digital input H-POSITION Moves the screen up and down.
Further Information Display modes The display mode the monitor uses is controlled by the computer. Therefore, you should refer to your computer documentation for details on how to change display modes. The image size, position and shape may change when the display mode changes. This is normal and the image can be readjusted using AUTO SETUP and the monitor controls. Unlike CRT monitors, which require a high refresh rate to minimize flicker, TFT technology is inherently flicker-free.
ENGLISH Power Management i If your computer has previously been used with a CRT monitor and is currently configured to a display mode outside the range that the Flat Panel monitor can display, you may need to re-attach the CRT monitor temporarily until you have reconfigured the computer, preferably to 1024 x 768 at 60Hz.
Troubleshooting If you have a problem setting up or using your monitor, you may be able to solve it yourself. Before calling your retailer or IBM, try the suggested actions that are appropriate to your problem. Problem 20 Possible Cause Suggested Action Reference Sreen is blank and power indicator is off. No power to monitor. • Ensure that the electrical outlet and the monitor are both switched on. • Check that the power cord is firmly plugged into the electrical outlet and the power supply unit.
ENGLISH Problem Sreen is blank and power indicator is flashing green every 0.5 second Sreen is blank and power indicator is flashing green every 0.5 or 1 second i For image problems, you may want to run AUTO SETUP again before consulting to this section. In most cases, AUTO SETUP can fix the problems. See Auto Setup for the computer on page 8 for details.
Further Help Machine Name – T545H Color Monitor Warranty Period – Three (3) Years See the IBM Statement of Limited Warranty included in this publication for IBM’s warranty terms and conditions. i If possible, stay by your computer. Your Technical Support Representative may wish to go through the problem with you during the call. The IBM Machine Warranty worldwide Web site at http://www-1.ibm.
ENGLISH 2. Lift the bottom of the cable cover (A) and pull it off. A B C 3. Lay the monitor facedown on a cushion and remove the four screws holding the hinge mechanism on the monitor. Lift off the hinge and base assembly(B). 4. If you are installing an arm or wall-mounting device, follow the directions included with the device. If you are just changing your cables, continue with step 5. 5. Squeeze the side of the rear cover (C) and pull it off. 6.
Specifications DVI-I Connector (Digital/Analog) 1 9 17 i 8 C1 C2 C5 16 24 C3 C4 The DVI - I (Digital Visual Interface - integrated) port supports analog and digital signal inputs and also improves quality of the displayed image by eliminating poor video at the monitor source. Pin Signal(DVI-I) Pin Signal(DVI-I) 1. T. M. D. S. Data2- 16. Hot Plug Detect 2. T. M. D. S. Data2+ 17. T. M. D. S. Data0- 3. T. M. D. S. Data2/4 Shield 18. T. M. D. S. Data0+ 4. T. M. D. S. Data4- 19. T. M. D.
ENGLISH Specifications This color monitor (Type-model 9493-Axx) uses a 15.1-inch TFT LCD. Dimensions Width: Depth: Height: 7.1 kg (15.62 lbs) Weight i Power consumption figures are for the monitor and the power supply combined. 401.3 mm 57 mm 250 mm(including stand) 338.5 mm (min lift) 463.5 mm (max lift) Stand Range Forward Tilt : Backward Tilt : Vertical Lift : Swivel : 0° 30° Range : 125mm Range : -150˚ / +150˚ Image Viewable Image Size: Maximum Height: Maximum Width: Pixel Pitch: 15.
Display Mode Ranges 26 Addressabillty Refresh Rate / Range ( + / - 3%) Horizontal Frequency / Range ( + / - 3%) 640 x 350 67.9 ~ 72.1 Hz 30.56 ~ 31.45 kHz 720 x 400 67.9 ~ 72.1 Hz 30.56 ~ 31.45 kHz 640 x 480 58.2 ~ 61.8 Hz 30.56 ~ 31.45 kHz 640 x 480 64.0 ~ 68.0 Hz 34.95 ~ 36.05 kHz 640 x 480 72.8 ~ 77.3 Hz 36.38 ~ 38.63 kHz 800 x 600 54.3 ~ 57.7 Hz 34.14 ~ 36.26 kHz 800 x 600 58.2 ~ 61.8 Hz 36.76 ~ 39.04 kHz 800 x 600 69.8 ~ 74.2 Hz 46.66 ~ 49.54 kHz 800 x 600 72.8 ~ 77.
ENGLISH Statement of Limited Warranty Part 1 - General Terms This Statement of Limited Warranty includes Part 1 - General Terms and Part 2 - Country-unique Terms. The terms of Part 2 replace or modify those of Part 1. The warranties provided by IBM in this Statement of Limited Warranty apply only to Machines you purchase for your use, and not for resale, from IBM or your reseller.
3. where applicable, before service is provided: a. follow the problem determination, problem analysis, and service request procedures that IBM or your reseller provides; b. secure all programs, data, and funds contained in a Machine; c. provide IBM or your reseller with sufficient, free, and safe access to your facilities to permit them to fulfill their obligations; and d. inform IBM or your reseller of changes in a Machine’s location.
ENGLISH CAMBODIA, LAOS, AND VIETNAM Governing Law: The following replaces “laws of the country in which you acquired the Machine” in the first sentence: laws of the State of New York. The following is added to this Section: Disputes and differences arising out of or in connection with this Agreement shall be finally settled by arbitration which shall be held in Singapore in accordance with the rules of the International Chamber of Commerce (ICC).
If you purchased an IBM Personal Computer Machine in Albania, Armenia, Belarus, Bosnia and Herzegovina, Bulgaria, Croatia, Czech Republic, Georgia, Hungary, Kazakhstan, Kirghizia, Federal Republic of Yugoslavia, Former Yugoslav Republic of Macedonia (FYROM), Moldova, Poland, Romania, Russia, Slovak Republic, Slovenia, or Ukraine, you may obtain warranty service for that Machine in any of those countries from either (1) an IBM reseller approved to perform warranty service or (2) from IBM.
ITALY Limitation of Liability: The following replaces the second sentence in the first paragraph: In each such instance unless otherwise provided by mandatory law, IBM is liable for no more than: 1. (unchanged) 2. as to any other actual damage arising in all situations involving non-performance by IBM pursuant to, or in any way related to the subject matter of this Statement of Warranty, IBM’s liability, will be limited to the total amount you paid for the Machine that is the subject of the claim.
Environmental Labelling of Personal Computers Congratulations! You have just purchased a TCO’95 approved and labelled product! Your choice has provided you with a product developed for professional use. Your purchase has also contributed to reducing the burden on the environment and to the further development of environmentally-adapted electronic products.
The energy requirements include a demand that the computer and/or display, after a certain period of inactivity, shall reduce its power consumption to a lower level, in one or more stages. The length of time to reactivate the computer shall be reasonable for the user. Labelled products must meet strict environmental demands, for example, in respect of the reduction of electric and magnetic fields, along with physical and visual ergonomics and good usability.
Cadmium is present in rechargeable batteries and in the color-generating layers of certain computer displays. Cadmium damages the nervous system and is toxic in high doses. The relevant bio-accumulative TCO’95 requirement states that batteries may not contain more than 25 ppm (parts per million) of cadmium. The color-generating layers of display screens must not contain any cadmium. Mercury is sometimes found in batteries, relays and switches. Mercury damages the nervous system and is toxic in high doses.
Environmental Labelling of Personal Computers Congratulations! You have just purchased a TCO’99 approved and labelled product! Your choice has provided you with a product developed for professional use. Your purchase has also contributed to reducing the burden on the environment and also to the further development of environmentally adapted electronics products.
Approval requirements cover a wide range of issues: environment, ergonomics, usability, emission of electric and magnetic fields, energy consumption and electrical and fire safety. The environmental demands impose restrictions on the presence and use of heavy metals, brominated and chlorinated flame retardants, CFCs (freons) and chlorinated solvents, among other things.
Environmental Flame retardants requirements Flame retardants are present in printed circuit boards, cables, wires, casings and housings. Their purpose is to prevent, or at least to delay the spread of fire. Up to 30% of the plastic in a computer casing can consist of flame retardant substances. Most flame retardants contain bromine or chloride, and those flame retardants are chemically related to another group of environmental toxins, PCBs.
Service Information The following parts are for use by IBM service, or IBM authorised dealers, to support the customer warranty. Parts are for service use only.
Compliances Federal Communications Commission (FCC) Statement IBM T545H color monitor Tested To Comply With FCC Standard FOR HOME OR OFFICE USE This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
For units intended to be operated at 230 volts (outside the U.S.): Use a cord set with a grounding-type attachment plug. The cord set should have the appropriate safety approvals for the country in which the equipment will be installed. IBM power cords for a specific country or region are usually available only in that country or region. IBM Fig. # (Plug Stnd.) 4 (NEMA 5-15P) 125V 5 (NEMA 6-15P) 250V IBM P/N Regions (1.
23 (BS 1363/A) 19 (DK2-5a) 25 (CEI 23-16) 2 (IRSM 2073) 62 (GB 2099.1) 32 (SI 32) 22 (SABS 164) 24 (1011-S24507) 14F0032 UK, United Arab Emirate (Dubai), China (Hong Kong S.A.R.
Congratulations! You have just purchased a TCO99 approved and labeled product! Your choice has provided you with a product developed for professional use. Your purchase has also contributed to reducing the burden on the environment and also to the further development of environmentally adapted electronics products.
products with regards to their eventual recycling and disposal. By proper selection of these materials and substances, the impact on the environment can be minimized. There are also other characteristics of a computer, such as energy consumption levels, that are important from the viewpoints of both the work (internal) and natural (external) environments.
European Union (EU) Statement This product is in conformity with the protection requirements of the EU Council Directive 89/366/ECC on the approximation of the laws of the Member States relating to electromagnetic compatibility. IBM can not accept responsibility for any failure to satisfy the protection requirements resulting from a nonrecommended modification of the product, including the fitting of non-IBM option cards.
Dieses Gerat ist berechtigt in Ubereinstimmungmit dem Deutschen EMVG das EG-Konformitatszeichen - CE - zu fuhren. Verantwortlich fur die Konformitatserklarung nach Paragraph 5 des EMVG ist die: IBM Deutschland Informationssysteme GmbH, 70548 Stuttgart. Informationen in Hinsicht EMVG Paragraph 3 Abs. (2) 2: Das Gerat erfullt die Schutzanforderungen nach EN 50082-1 und EN 55022 Klasse B.
IBM non accetta responsabilità alcuna per la mancata conformità alle normative di protezione dovuta a modifiche non consi gliate al prodotto, compresa l’installazione di schede e componenti di marca diversa da IBM. Le prove effettuate sul presente prodotto hanno accertato che esso rientra nei limiti stabiliti per le le apparecchiature di informatica Classe B ai sensi del CISPR 22 / Norma Europea EN 55022.
VCCI Class B Notice (Japan Only) This equipment complies with the limits for a Class B digital device (devices used in or adjacent to a residential environment) and conforms to the standards for information technology equipment that are set by the Voluntary Control Council for Interference for preventing radio frequency interference in residential areas.