ThinkCentre Edge Hardware Maintenance Manual Machine Types: 5068, 7558, and 7567
ThinkCentre Edge Hardware Maintenance Manual Machine Types: 5068, 7558, and 7567
Note: Before using this information and the product it supports, be sure to read and understand the ThinkCentre Edge Safety and Warranty Guide and Appendix A “Notices” on page 155. Second Edition (September 2011) © Copyright Lenovo 2011. LIMITED AND RESTRICTED RIGHTS NOTICE: If data or software are delivered pursuant a General Services Administration “GSA” contract, use, reproduction, or disclosure is subject to restrictions set forth in Contract No. GS-35F-05925.
Contents Chapter 1. About this manual . . . . . . 1 Important Safety Information . . . . . . . . . . 1 Chapter 2. Safety information . . . . . . 3 General safety . . . . . . . . . . . . Electrical safety . . . . . . . . . . . Safety inspection guide . . . . . . . . Handling electrostatic discharge-sensitive devices . . . . . . . . . . . . . . Grounding requirements . . . . . . . . Safety notices (multi-lingual translations) . . . . . . . . . . . . . 3 3 5 . . . . . . . . . . . . 5 6 6 Chapter 3.
Installing or replacing a memory module Replacing the internal speakers . . . . Replacing the integrated camera . . . Replacing the system board . . . . . Replacing the LCD panel. . . . . . . Replacing the WI-FI card. . . . . . . Completing the parts replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Chapter 9. FRU lists . . . . . . . . . Overall: MT 5068, 7558, and 7567 . Mechanical FRUs . . . . . . . Adapters and miscellaneous FRUs . Keyboard and Mouse . . . . . . Power Cords .
Chapter 1. About this manual This manual contains service and reference information for ThinkCentre® computers listed on the cover. It is intended only for trained servicers who are familiar with Lenovo® computer products. Before servicing a Lenovo product, be sure to read the Safety Information in Chapter 2 “Safety information” on page 3. The Symptom-to-FRU Index and Additional Service Information chapters are not specific to any machine type and are applicable to all ThinkCentre Edge computers.
2 ThinkCentre Edge Hardware Maintenance Manual
Chapter 2. Safety information This chapter contains the safety information that you need to be familiar with before servicing a computer. General safety Follow these rules to ensure general safety: • Observe good housekeeping in the area of the machines during and after maintenance. • When lifting any heavy object: 1. Ensure you can stand safely without slipping. 2. Distribute the weight of the object equally between your feet. 3. Use a slow lifting force.
Important: Use only approved tools and test equipment. Some hand tools have handles covered with a soft material that does not insulate you when working with live electrical currents. Many customers have, near their equipment, rubber floor mats that contain small conductive fibers to decrease electrostatic discharges. Do not use this type of mat to protect yourself from electrical shock. • Find the room emergency power-off (EPO) switch, disconnecting switch, or electrical outlet.
Safety inspection guide The intent of this inspection guide is to assist you in identifying potentially unsafe conditions on these products. Each machine, as it was designed and built, had required safety items installed to protect users and service personnel from injury. This guide addresses only those items. However, good judgment should be used to identify potential safety hazards due to attachment of features or options not covered by this inspection guide.
• Wear a grounded wrist strap against your skin to eliminate static on your body. • Prevent the part from touching your clothing. Most clothing is insulative and retains a charge even when you are wearing a wrist strap. • Use the black side of a grounded work mat to provide a static-free work surface. The mat is especially useful when handling ESD-sensitive devices. • Select a grounding system, such as those listed below, to provide protection that meets the specific service requirement.
• When possible, use one hand only to connect or disconnect signal cables. • Never turn on any equipment when there is evidence of fire, water, or structural damage. • Disconnect the attached power cords, telecommunications systems, networks, and modems before you open the device covers, unless instructed otherwise in the installation and configuration procedures.
≥18 kg (37 lbs) ≥32 kg (70.5 lbs) ≥55 kg (121.2 lbs) CAUTION: Use safe practices when lifting. CAUTION: The power control button on the device and the power switch on the power supply do not turn off the electrical current supplied to the device. The device also might have more than one power cord. To remove all electrical current from the device, ensure that all power cords are disconnected from the power source.
Chapter 2.
≥18 kg (37 lbs) ≥32 kg (70.5 lbs) ≥55 kg (121.
A corrente elétrica proveniente de cabos de alimentação, de telefone e de comunicações é perigosa. Para evitar risco de choque elétrico: • Não conecte nem desconecte nenhum cabo ou execute instalação, manutenção ou reconfiguração deste produto durante uma tempestade com raios. • Conecte todos os cabos de alimentação a tomadas elétricas corretamente instaladas e aterradas. • Todo equipamento que for conectado a este produto deve ser conectado a tomadas corretamente instaladas.
• Não remova as tampas. A remoção das tampas de um produto a laser pode resultar em exposição prejudicial à radiação de laser. Não existem peças que podem ser consertadas no interior do dispositivo. • A utilização de controles ou ajustes ou a execução de procedimentos diferentes dos especificados aqui pode resultar em exposição prejudicial à radiação. PERIGO Alguns produtos a laser contêm diodo de laser integrado da Classe 3A ou da Classe 3B. Observe o seguinte: Radiação a laser quando aberto.
Chapter 2.
2 1 14 ThinkCentre Edge Hardware Maintenance Manual
Chapter 2.
2 1 DANGER Le courant électrique provenant de l'alimentation, du téléphone et des câbles de transmission peut présenter un danger. Pour éviter tout risque de choc électrique : • Ne manipulez aucun câble et n'effectuez aucune opération d'installation, d'entretien ou de reconfiguration de ce produit au cours d'un orage. • Branchez tous les cordons d'alimentation sur un socle de prise de courant correctement câblé et mis à la terre.
Connexion Déconnexion 1. Mettez les unités HORS TENSION. 1. Mettez les unités HORS TENSION. 2. Commencez par brancher tous les cordons sur les unités. 2. Débranchez les cordons d'alimentation des prises. 3. Branchez les câbles d'interface sur des connecteurs. 4. Débranchez tous les câbles des unités. 3. Débranchez les câbles d'interface des connecteurs. 4. Branchez les cordons d'alimentation sur des prises. 5. Mettez les unités SOUS TENSION.
≥18 kg (37 lbs) ≥32 kg (70.5 lbs) ≥55 kg (121.2 lbs) ATTENTION: Soulevez la machine avec précaution. ATTENTION: L'interrupteur de contrôle d'alimentation de l'unité et l'interrupteur dubloc d'alimentation ne coupent pas le courant électrique alimentantl'unité. En outre, le système peut être équipé de plusieurs cordonsd'alimentation. Pour mettre l'unité hors tension, vous devez déconnectertous les cordons de la source d'alimentation.
• Die Verbindung zu den angeschlossenen Netzkabeln, Telekommunikationssystemen, Netzwerken und Modems ist vor dem Öffnen des Gehäuses zu unterbrechen, sofern in den Installations- und Konfigurationsprozeduren keine anders lautenden Anweisungen enthalten sind. • Zum Installieren, Transportieren und Öffnen der Abdeckungen des Computers oder der angeschlossenen Einheiten die Kabel gemäß der folgenden Tabelle anschließen und abziehen.
Laserstrahlung bei geöffneter Verkleidung. Nicht in den Strahl blicken. Keine Lupen oder Spiegel verwenden. Strahlungsbereich meiden. ≥18 kg ≥32 kg ≥55 kg ACHTUNG: Arbeitsschutzrichtlinien beim Anheben der Maschine beachten. ACHTUNG: Mit dem Netzschalter an der Einheit und am Netzteil wird die Stromversorgung für die Einheit nicht unterbrochen. Die Einheit kann auch mit mehreren Netzkabeln ausgestattet sein.
Chapter 2.
2 1 PERICOLO La corrente elettrica proveniente dai cavi di alimentazione, del telefono e di comunicazione può essere pericolosa. Per evitare il rischio di scosse elettriche: • Non collegare o scollegare qualsiasi cavo oppure effettuare l'installazione, la manutenzione o la riconfigurazione del prodotto durante un temporale. • Collegare tutti i fili elettrici a una presa di alimentazione correttamente cablata e dotata di messa a terra.
• Se possibile, utilizzare solo una mano per collegare o scollegare i cavi di segnale. • Non accendere assolutamente apparecchiature in presenza di incendi, perdite d'acqua o danno strutturale. • Scollegare i cavi di alimentazione, i sistemi di telecomunicazione, le reti e il modem prima di aprire i coperchi del dispositivo, salvo istruzioni contrarie relative alle procedure di installazione e configurazione.
PERICOLO Alcune unità laser contengono un diodo laser di Classe 3A o Classe 3B. Tener presente quanto segue: Aprendo l'unità vengono emesse radiazioni laser. Non fissare il fascio, non guardarlo direttamente con strumenti ottici ed evitare l'esposizione al fascio. ≥18 kg ≥32 kg ≥55 kg ATTENZIONE: Prestare attenzione nel sollevare l'apparecchiatura.
Chapter 2.
2 1 PELIGRO La corriente eléctrica procedente de cables de alimentación, teléfonos y cables de comunicación puede ser peligrosa. Para evitar el riesgo de descarga eléctrica: • No conecte ni desconecte los cables ni realice ninguna tarea de instalación, mantenimiento o reconfiguración de este producto durante una tormenta eléctrica. • Conecte todos los cables de alimentación a tomas de corriente debidamente cableadas y conectadas a tierra.
• Desconecte los cables de alimentación, los sistemas de telecomunicaciones, las redes y los módems conectados antes de abrir las cubiertas de los dispositivos, a menos que se indique lo contrario en los procedimientos de instalación y configuración. • Conecte y desconecte los cables, como se describe en la tabla siguiente, cuando instale, mueva o abra las cubiertas de este producto o de los dispositivos conectados. Para conectar Para desconectar 1. APÁGUELO todo. 1. APÁGUELO todo. 2.
Algunos productos láser tienen incorporado un diodo láser de clase 3A o clase 3B. Tenga en cuenta lo siguiente: Cuando se abre, queda expuesto a radiación láser. No mire directamente al rayo láser, ni siquiera con instrumentos ópticos, y evite exponerse directamente al rayo láser. ≥18 kg ≥32 kg ≥55 kg PRECAUCIÓN: Adopte procedimientos seguros al levantar el equipo.
Chapter 3. General information This chapter provides general information that applies to all machine types supported by this publication. Lenovo ThinkVantage Tools The Lenovo ThinkVantage® Tools program guides you to a host of information sources and provides easy access to various tools to help you work more easily and securely. To access the Lenovo ThinkVantage Tools program, click Start ➙ All Programs ➙ Lenovo ThinkVantage Tools.
• Troubleshooting information • Parts information • Downloads and drivers • Links to other useful sources of information To access this information, go to: http://www.lenovo.com/support Specifications This section lists the physical specifications for your computer. Dimensions Width: 406 mm (15.98 inches) Height: 512 mm (20.16 inches) Depth: 71.5 mm (2.81 inches) Weight Maximum configuration as shipped: 8 kg (17.
Chapter 4. General Checkout Attention The drives in the computer you are servicing might have been rearranged or the drive startup sequence changed. Be extremely careful during write operations such as copying, saving, or formatting. Data or programs can be overwritten if you select an incorrect drive. General error messages appear if a problem or conflict is found by an application program, the operating system, or both.
– Has this configuration ever worked? – If it has been working, what changes were made prior to it failing? – Is this the original reported failure? • Diagnostics version – Type and version level • Hardware configuration – Print (print screen) configuration currently in use – BIOS level • Operating system software – Type and version level Notes: To eliminate confusion, identical systems are considered identical only if they: 1. Are the exact machine type and models 2. Have the same BIOS level 3.
Chapter 5. Troubleshooting and diagnostics This chapter describes some basic troubleshooting and diagnostic programs. If your computer problem is not described here, see “Diagnostics” on page 49 for additional troubleshooting resources. Basic troubleshooting The following table provides information to help you troubleshoot your computer problems. Note: If you cannot correct the problem, have the computer serviced.
Symptom The wireless keyboard or mouse does not work. Action Verify that: • The computer is turned on. • The battery or batteries installed in the wireless keyboard or mouse are in good condition. • The wireless configurations are all set correctly. You might need to refer to the documentation that come with the wireless keyboard or mouse, or refer to your Windows Help and Support information system for wireless related instructions.
Troubleshooting Use the troubleshooting information to find solutions to problems that have definite symptoms. If the symptom your computer is experiencing occurred immediately after a new hardware option or new software installed, do the following before referring to the troubleshooting information: 1. Remove the new hardware option or software. If you must remove the computer cover to remove a hardware option, have the computer serviced. For your safety, do not operate the computer with the cover removed.
• Some models have a front audio panel you can use to adjust volume. If you have a front audio panel, verify that the volume is not set too low. • Verify that your external speakers (and headphones, if used) are connected to the correct audio connector on the computer. Most speaker cables are color-coded to match the connector. Note: When external-speaker or headphone cables are attached to the audio connector, the internal speaker, if present, is disabled.
• • “A CD or DVD does not work” on page 37 “Unable to use a startable (bootable) recovery medium, such as the Product Recovery CD, to start your computer” on page 37 An audio disc or AutoPlay-enabled disc does not automatically play when it is inserted into a CD drive Symptom: An audio disc or AutoPlay-enabled disc does not automatically play when it is inserted into a CD drive.
Black screen instead of DVD video Symptom: Black screen instead of DVD video Actions: • Restart the DVD player program. • Close any open files, turn off the computer, and then restart the computer. • Try a lower screen resolution or color depth. If these actions do not correct the problem, run the diagnostic programs (see “Diagnostics” on page 49 for instructions). If you need technical assistance, see “Additional information resources” on page 29. DVD movie will not play Symptom: DVD movie will not play.
• Ensure that a DVD disc is in the drive with the shiny side of the disc facing down. • Ensure that video resolution is set to less than 1152 x 864. • On computers that have a CD-ROM or CD-RW drive in addition to a DVD-ROM drive, make sure that the DVD disc is in the drive labeled “DVD”. If these actions do not correct the problem, run the diagnostic programs (see “Diagnostics” on page 49 for instructions). If you need technical assistance, see “Additional information resources” on page 29.
If these actions do not correct the problem, have the computer and keyboard serviced. See “Additional information resources” on page 29 for details. The mouse or pointing device does not work Symptom: The mouse or pointing device does not work. Actions: • Verify that the mouse or pointing-device cable is securely attached to the correct connector on the computer. Depending on the type of mouse you have, the mouse cable will connect to either the mouse, serial, or USB connector.
Monitor problems Note: Many monitors have status-indicator lights and built-in controls for adjusting brightness, contrast, width, height, and other picture adjustments. However, the controls vary from monitor type to monitor type.
problem. Move fluorescent desk lighting or any equipment that produces magnetic fields farther away from the monitor. If this does not correct the problem, do the following: 1. Turn off the monitor. (Moving a color monitor while it is turned on might cause screen discoloration.) 2. Adjust the placement of the monitor and other devices so that they are at least 305 mm (12 inches) apart. 3. Turn on the monitor.
Actions: Make sure that: • The cable is installed properly. The network cable must be securely connected to both the Ethernet connector of your computer and the RJ45 connector of the hub. The maximum allowable distance from the computer to hub is 100 meters. If the cable is connected and the distance is within acceptable limits but the problem persists, try a different cable. • The cable is installed properly. • You are using the correct device driver. On the Windows 7 operating system, do the following: 1.
If your computer is a Gigabit Ethernet model, it cannot connect to the network at 1000 Mbps. Instead, it connects at 100 Mbps Symptom: If your computer is a Gigabit Ethernet model, it cannot connect to the network at 1000 Mbps. Instead, it connects at 100 Mbps. Actions: • Try another cable. • Make sure that the link partner is set to auto-negotiate. • Make sure that the switch is 802.3ab-compliant (gigabit over copper).
4. Select the Playback tab. 5. If you are using Headset profile, select Bluetooth Hands-free Audio and click the Set Default button. If you are using AV profile, select Stereo Audio and click the Set Default button. 6. Click OK to close the Sound window.
• Verify that the option and any required device drivers are installed correctly. If these actions do not correct the problem, run the diagnostic programs (see “Diagnostics” on page 49 for instructions). If you need technical assistance, see “Additional information resources” on page 29.
• Clean out your Inbox, Sent Items, and Deleted Items folders from your e-mail application. The folder names and procedures vary depending on your e-mail application. If you need assistance, see the help system for your e-mail application. Excessive number of fragmented files Symptom: Excessive number of fragmented files Action: Run the Windows Disk Defragmenter program.
• If the serial device has its own On/Off switch, make sure it is in the On position. • If the serial device has an Online switch, make sure it is in the Online position. • If the serial device is a printer, make sure paper is loaded correctly. • Verify that any software supplied with the serial device is correctly installed. Refer to the documentation for the serial-device option. • Make sure that the serial-port adapter, if you added one, is properly installed and firmly seated.
• If the software program used to work correctly, but does not work correctly now, do the following: On the Windows 7 operating system, click Start ➙ Control Panel ➙ System and Security ➙ System ➙ System Protection ➙ System Restore. • If you are unable to resolve the problem through other methods, uninstall the software program and reinstall it. If these actions do not correct the problem, you might need technical assistance.
To run the Lenovo ThinkVantage Toolbox program on the Windows 7 operating system, click Start ➙ All Programs ➙ Lenovo ThinkVantage Tools ➙ System Health and Diagnostics. Follow the instructions on the screen. Follow the instructions on the screen. For additional information, refer to the Lenovo ThinkVantage Toolbox help system. PC-Doctor for DOS You can also download the latest version of the PC-Doctor for DOS diagnostic program from http://www.lenovo.com/support.
• Using the cursor movement keys, highlight Run Normal Test or Run Quick Test from the Diagnostics menu and then press Enter. This automatically runs a pre-defined group of tests from each test category. Run Normal Test runs a more extensive set of tests than does Run Quick Test and takes longer to complete. • Press F5 to automatically run all selected tests in all categories. • From within a test category, press Ctrl-Enter to automatically run only the selected tests in that category.
• Full Erase Hard Drive Quick Erase Hard Drive provides a DOS utility that performs the following: • Destroys the Master Boot Record (MBR) on the hard drive. • Destroys all copies of the FAT Table on all partitions (both the master and backup). • Destroys the partition table. • Provides messages that warn the user that this is a non-recoverable process. Full Erase Hard Drive provides a DOS utility that performs the following: • Performs all the steps in Quick Erase.
Chapter 6. Using the Setup Utility program The Setup Utility program is used to view and change the configuration settings of your computer, regardless of which operating system you are using. However, the operating system settings might override any similar settings in the Setup Utility program. Starting the Setup Utility program To start the Setup Utility program, do the following: 1. Make sure your computer is turned off. 2. Repeatedly press and release the F1 key when turning on the computer.
• Have at least eight characters in length • Contain at least one alphabetic character and one numeric character • Setup Utility program is not case sensitive • Not be your name or your user name • Not be a common word or a common name • Be significantly different from your previous passwords Power-On Password When a Power-On Password is set, you are prompted to type a valid password each time the computer is turned on. The computer cannot be used until the valid password is typed in.
• Select ATA Drive Setup to enable or disable an internal or external SATA device. 4. Select the desired settings and press Enter. 5. Press F10 to save changes and exit the Setup Utility program. See “Exiting the Setup Utility program” on page 55. Selecting a startup device If your computer does not start up from a device such as the disc or hard disk drive as expected, do one of the following to select the startup device you want.
56 ThinkCentre Edge Hardware Maintenance Manual
Chapter 7. Symptom-to-FRU Index The Symptom-to-FRU index lists error symptoms and possible causes. The most likely cause is listed first. Always begin with Chapter 4 “General Checkout” on page 31. This index can also be used to help you decide which FRUs to have available when servicing a computer. If you are unable to correct the problem using this index, go to “Undetermined problems” on page 78. Notes: • If you have both an error message and an incorrect audio response, diagnose the error message first.
Diagnostic error codes Refer to the following diagnostic error codes when using the diagnostic tests. See “Running tests” on page 50 for the specific type for information about the diagnostic programs. In the following index, X can represent any number. Diagnostic Error Code FRU/Action 000-000-XXX BIOS Test Passed No action 000-002-XXX BIOS Timeout 1. Flash the system. See “Flash update procedures” on page 151. 2. System board 000-024-XXX BIOS Addressing test failure 1. Flash the system.
Diagnostic Error Code 000-197-XXX BIOS test warning FRU/Action 1. Make sure the component that is called out is connected and/or enabled. See Chapter 6 “Using the Setup Utility program” on page 53. 2. Re-run test. 3. Replace the component that is called out in warning statement 4. Replace the component under test. 000-198-XXX BIOS test aborted 1. Make sure the component that is called out is connected and/or enabled. See Chapter 6 “Using the Setup Utility program” on page 53. 2.
Diagnostic Error Code 001-038-XXX System Extension failure FRU/Action 1. Adapter card 2. System board 001-039-XXX System DMI data structure error 1. Flash the system. See “Flash update procedures” on page 151. 2. System board 001-040-XXX System IRQ failure 1. Power-off/on system and re-test. 2. System board 001-041-XXX System DMA failure 1. Power-off/on system and re-test. 2.
Diagnostic Error Code 001-273-XXX System IRQ6 (diskette drive) failure FRU/Action 1. Diskette Cable 2. Diskette drive 3. System board 001-274-XXX System IRQ7 failure 1. Device on IRQ7 2. System board 001-275-XXX System IRQ8 failure 1. Device on IRQ8 2. System board 001-276-XXX System IRQ9 failure 1. Device on IRQ9 2. System board 001-277-XXX System IRQ10 failure 1. Device on IRQ10 2. System board 001-278-XXX System IRQ11 failure 1. Device on IRQ11 2.
Diagnostic Error Code 005-016-XXX Video Simple Pattern test failure FRU/Action 1. Video Ram 2. Video card, if installed 3. System board 005-024-XXX Video Addressing test failure 1. Video card, if installed 2. System board 005-025-XXX Video Checksum Value error 1. Video card, if installed 2. System board 005-027-XXX Video Configuration/Setup error 1. Run the Setup Utility program. 2. Video drivers update 3. Video card, if installed 4. System board 005-031-XXX Video Device Cable failure 1.
Diagnostic Error Code 005-2XX-XXX 005-3XX-XXX Video subsystem error FRU/Action 1. Video card, if installed 2. System board 006-000-XXX Diskette interface Test Passed 006-0XX-XXX Diskette interface error No action 1. Diskette drive Cable 2. Diskette drive 3. System board 006-195-XXX Diskette interface Test aborted by user Information only Restart the test, if necessary 006-196-XXX Diskette interface test halt, error threshold exceeded 1. Press F3 to review the log file.
Diagnostic Error Code 011-196-XXX Serial port test halt, error threshold exceeded FRU/Action 1. Press F3 to review the log file. 2. Restart the test to reset the log file. 011-197-XXX Serial port test warning 1. Make sure the component that is called out is connected and/or enabled. See Chapter 6 “Using the Setup Utility program” on page 53. 2. Re-run test 3. Replace the component that is called out in warning statement. 4. Replace the component under test. 011-198-XXX Serial port test aborted 1.
Diagnostic Error Code 014-197-XXX Parallel port test warning FRU/Action 1. Make sure the component that is called out is connected and/or enabled. See Chapter 6 “Using the Setup Utility program” on page 53. 2. Re-run test. 3. Replace the component that is called out in warning statement. 4. Replace the component under test. 014-198-XXX Parallel port test aborted 1. If a component is called out, make sure it is connected and/or enabled. 2. Flash the system and re-test.
Diagnostic Error Code 015-196-XXX USB port test halt, error threshold exceeded FRU/Action 1. Press F3 to review the log file. 2. Restart the test to reset the log file. 015-197-XXX USB port test warning 1. Make sure the component that is called out is connected and/or enabled. See Chapter 6 “Using the Setup Utility program” on page 53. 2. Re-run test. 3. Replace the component that is called out in warning statement. 4. Replace the component under test. 015-198-XXX USB port test aborted 1.
Diagnostic Error Code 018-250-XXX PCI Card Services error FRU/Action 1. PCI card 2. Riser card, if installed. 3. System board 020-000-XXX PCI Interface Test Passed 020-0XX-XXX PCI Interface error No action 1. PCI card 2. Riser card, if installed. 3. System board 020-195-XXX PCI Test aborted by user 020-196-XXX PCI test halt, error threshold exceeded Information only Restart the test, if necessary 1. Press F3 to review the log file. 2. Restart the test to reset the log file.
Diagnostic Error Code 025-02X-XXX 025-03X-XXX 025-04X-XXX IDE Interface failure FRU/Action 1. IDE signal cable 2. Check power supply. 3. Reseat IDE signal cable. 4. IDE device 5. System board 025-195-XXX IDE interface Test aborted by user Information only Restart the test, if necessary. 025-196-XXX IDE interface test halt, error threshold exceeded 1. Press F3 to review the log file. 025-197-XXX IDE interface test warning 1. Make sure the component that is called out is connected and/or enabled.
Diagnostic Error Code FRU/Action 030-196-XXX SCSI interface test halt, error threshold exceeded 1. Press F3 to review the log file. 030-197-XXX SCSI interface test warning 1. Make sure the component that is called out is connected and/or enabled. See Chapter 6 “Using the Setup Utility program” on page 53. 2. Restart the test to reset the log file. 2. Re-run test. 3. Replace the component that is called out in warning statement. 4. Replace the component under test.
Diagnostic Error Code 071-00X-XXX 071-01X-XXX 071-02X-XXXAudio port error FRU/Action 1. Run the Setup Utility program. 2. Flash the system. See “Flash update procedures” on page 151. 3. System board 071-03X-XXX Audio port failure 1. Speakers 2. Microphone 3. Audio card, if installed. 4. System board 071-04X-XXX Audio port failure 1. Run the Setup Utility program. 2. Audio card, if installed. 3.
Diagnostic Error Code 080-197-XXX Game Port interface test warning FRU/Action 1. Make sure the component that is called out is connected and/or enabled. See Chapter 6 “Using the Setup Utility program” on page 53. 2. Re-run test. 3. Replace the component that is called out in warning statement. 4. Replace the component under test. 080-198-XXX Game Port interface test aborted 1. If a component is called out, make sure it is connected and/or enabled.
Diagnostic Error Code 086-199-XXX Mouse Port interface test failed, cause unknown FRU/Action 1. See “Undetermined problems” on page 78. 2. Flash the system and re-test. See “Flash update procedures” on page 151. 3. Replace component under function test. 089-000-XXX Microprocessor Test Passed 089-XXX-XXX Microprocessor failure No action 1. Microprocessor(s) 2. System board 089-195-XXX Microprocessor Test aborted by user Information only Restart the test, if necessary.
Diagnostic Error Code 170-199-XXX Voltage Sensor(s) test failed, cause unknown FRU/Action 1. See “Undetermined problems” on page 78. 2. Flash the system and re-test. See “Flash update procedures” on page 151. 3. Replace component under function test. 170-250-XXX 170-251-XXX Voltage Sensor(s) Voltage limit error 1. Power supply 170-254-XXX Voltage Sensor(s) Voltage Regulator Module error 1. Voltage Regulator Module (VRM) 2. System board 2. Microprocessor 3.
Diagnostic Error Code 201-XXX-XXX System Memory error FRU/Action 1. Replace the memory module called out by the test. 2. System board 202-000-XXX System Cache Test Passed 202-XXX-XXX System Cache error No action 1. Cache, if removable 2. System board 3. Microprocessor 206-000-XXX Diskette Drive Test Passed 206-XXX-XXX Diskette Drive error No action 1. Diskette Drive Cable 2. Check power supply voltages 3. Diskette drive 4.
Diagnostic Error Code FRU/Action 305-000-XXX Monitor DDC Test Passed No action 305-250-XXX Monitor DDC self test failure 1. Run the Setup Utility program to enable DDC. 2. Cable 3. Monitor 4. Video card 5. System board 415-000-XXXModem Test Passed No action 415-XXX-XXX Modem error Remove the Modem and re-test the system. Beep symptoms Beep symptoms are tones or a series of tones separated by pauses (intervals without sound) during POST. The following tables describes beep symptoms.
Error code POST Error Message Description/Action 0135 Fan failure The system might be overheating. Press F10 to exit. Note: If the problem is caused by the microprocessor fan, press F10 will not solve the problem. 0211 Keyboard not found When there is no keyboard detected, the error message will be displayed. 0164 Memory size decreased Press F10 to exit. 1762 Configuration change has occurred This error message is displayed when a hard disk drive or optical drive change has been made.
Message/Symptom Computer will not perform a Wake On LAN® (if applicable) FRU/Action 1. Check power supply and signal cable connections to network adapter. 2. Ensure that the operating system settings are set to enable Wake on LAN. 3. Ensure Wake On LAN feature is enabled in Setup/Configuration (see “Starting the Setup Utility program” on page 53) 4. Ensure network administrator is using correct MAC address. 5. Ensure no interrupt or I/O address conflicts. 6.
Message/Symptom Program loads from the hard disk with a known-good diagnostics diskette in the first 3.5-inch diskette drive FRU/Action 1. Run the Setup Utility program and check Startup sequence. 2. Diskette Drive 3. Diskette Drive Cable 4. System Board 5. Power Supply RPL computer cannot access programs from its own hard disk. 1. If network administrator is using LCCM Hybrid RPL, check startup sequence: a. First device - network b. Second device - hard disk 2.
Chapter 8. Replacing FRUs This chapter provides removal or replacement procedures for major FRUs. Not all FRUs are documented. Important Before you replace any FRU, read Chapter 2 “Safety information” on page 3. These precautions and guidelines will help you work safely. FRU replacements are to be done by trained service technicians only.
Locating connectors, controls, and indicators on the front of your computer Figure 1 “Front connector, control, and indicator locations” on page 80 shows the locations of the connectors, controls, and indicators on the front of your computer. Figure 1.
Locating connectors on the rear of your computer Figure 2 “Rear connector locations” on page 81 shows the locations of the connectors on the rear of your computer. Some connectors on the rear of your computer are color-coded to help you determine where to connect the cables on your computer. Figure 2.
FRU locations The following illustration shows the locations of the FRUs. Figure 3.
7 Heat sink assembly 21 Foot stand 8 Microprocessor 22 Hard disk drive 9 Memory module 23 LCD bracket 10 Battery 24 LCD panel 11 Microprocessor fan 25 Inverter 12 System board 26 Optical drive 13 Card reader 27 VESA mount bracket 14 Foot stand 28 Integrated camera Chapter 8.
System board parts and connectors The following illustration shows the locations of the system board parts and connectors. Figure 4.
Removing and reinstalling the system stand hinge cover Attention Do not open your computer or attempt any repair before reading and understanding the “Important safety information” in the ThinkCentre Edge Safety and Warranty Guide that came with your computer. To obtain a copy of the ThinkCentre Edge Safety and Warranty Guide, go to: http://www.lenovo.com/support This section provides instructions on how to remove and reinstall the system stand hinge cover.
6. To reinstall the system stand hinge cover, place the system stand hinge cover on the computer so that the two plastic tabs on the hinge cover align with the corresponding holes in the computer. Figure 6. Reinstalling the system stand hinge cover 7. Reinstall the screw to secure the system stand hinge cover to the computer. Figure 7.
This section provides instructions on how to remove and reinstall the system stand. To remove and reinstall the system stand, do the following: 1. Turn off the computer and disconnect all power cords from electrical outlets. 2. Remove the system stand hinge cover. See “Removing and reinstalling the system stand hinge cover” on page 85. 3. Remove the two screws that secure the system stand, and then lift the system stand up and remove it from the computer. Figure 8. Removing the system stand 4.
5. Reinstall the system stand hinge cover. See “Removing and reinstalling the system stand hinge cover” on page 85. Removing and reinstalling the foot stands Attention Do not open your computer or attempt any repair before reading and understanding the “Important safety information” in the ThinkCentre Edge Safety and Warranty Guide that came with your computer. To obtain a copy of the ThinkCentre Edge Safety and Warranty Guide, go to: http://www.lenovo.
Figure 11. Loosening the screw that secures the foot stand 7. To reinstall the foot stand, place the foot stand on the computer so that the screw hole aligns with the corresponding hole in the computer, and then tighten the screw to secure the foot stand to the computer. Figure 12. Tightening the screw to secure the foot stand to the computer 8. Reinstall the rubber on the foot stand. Chapter 8.
Figure 13. Reinstall the rubber on the foot stand.
Removing the computer cover Attention Do not open your computer or attempt any repair before reading and understanding the “Important safety information” in the ThinkCentre Edge Safety and Warranty Guide that came with your computer. To obtain a copy of the ThinkCentre Edge Safety and Warranty Guide, go to: http://www.lenovo.com/support This section provides instructions on how to remove the computer cover.
Replacing the hard disk drive Attention Do not open your computer or attempt any repair before reading and understanding the “Important safety information” in the ThinkCentre Edge Safety and Warranty Guide that came with your computer. To obtain a copy of the ThinkCentre Edge Safety and Warranty Guide, go to: http://www.lenovo.com/support This section provides instructions on how to replace the hard disk drive. To replace the hard disk drive, do the following: 1.
Figure 16. Removing the hard disk drive 6. Remove the four screws on the hard disk drive bracket, then remove the hard disk drive out of the bracket. Do not touch the circuit board on the bottom of the hard disk drive. Figure 17. Removing the hard disk drive out of the bracket 7. To install the new hard disk drive into the bracket, position the hard disk drive so that the four screw holes align with those in the bracket. 8.
Replacing the optical drive Attention Do not open your computer or attempt any repair before reading and understanding the “Important safety information” in the ThinkCentre Edge Safety and Warranty Guide that came with your computer. To obtain a copy of the ThinkCentre Edge Safety and Warranty Guide, go to: http://www.lenovo.com/support This section provides instructions on how to replace the optical drive. Note: The optical drive is available only in some models.
Figure 19. Installing the optical drive 7. Install the screw 1 to secure the optical drive. Figure 20. Installing the screw to secure the optical drive 8. Go to “Completing the parts replacement” on page 121. Removing the VESA mount bracket Attention Do not open your computer or attempt any repair before reading and understanding the “Important safety information” in the ThinkCentre Edge Safety and Warranty Guide that came with your computer.
To remove the VESA mount bracket, do the following: 1. Remove all media from the drives and turn off all attached devices and the computer. Then, disconnect all power cords from electrical outlets and disconnect all cables that are connected to the computer. 2. Place a soft, clean towel or cloth on the desk or other flat surface. Hold the sides of your computer and gently lay it down so that the screen is against the surface and the cover is facing up. 3. Remove the computer cover.
To replace the rear I/O assembly, do the following: 1. Remove all media from the drives and turn off all attached devices and the computer. Then, disconnect all power cords from electrical outlets and disconnect all cables that are connected to the computer. 2. Place a soft, clean towel or cloth on the desk or other flat surface. Hold the sides of your computer and gently lay it down so that the screen is against the surface and the cover is facing up. 3. Remove the computer cover.
6. Turn the rear I/O assembly up side down, and then remove the two screws that secure the power cord connector to the power cord connector bracket. Remove the rear I/O assembly from the computer. Figure 23. Removing the power cord connector 7. To reinstall the rear I/O assembly, reinstall the two screws that secure the power cord connector to the power cord connector bracket.
5. Remove the screw that secures the system board shield, and then slide the system board shield out of the computer. Figure 24. Removing the system board shield 6. To reinstall the system board shield, slide the system board shield into the system board shield slot so that the screw hole aligns with that in the computer. 7. Reinstall the screw to secure the system board shield to the computer. 8. Go to “Completing the parts replacement” on page 121.
9. Remove the three screws 1 that secure the power supply. Figure 25. Removing the three screws that secure the power supply 10. To reinstall the power supply, reinstall the two screws that secure the power cord connector to the power connector bracket. See “Replacing the rear I/O assembly” on page 96 11. Position the new power supply in the computer and align the three screw holes in the new power supply with those in the computer main bracket. Install the three screws to secure the new power supply. 12.
1. Remove all media from the drives and turn off all attached devices and the computer. Then, disconnect all power cords from electrical outlets and disconnect all cables that are connected to the computer. 2. Place a soft, clean towel or cloth on the desk or other flat surface. Hold the sides of your computer and gently lay it down so that the screen is against the surface and the cover is facing up. 3. Remove the computer cover. See “Removing the computer cover” on page 91. 4.
copy of the ThinkCentre Edge Safety and Warranty Guide, go to: http://www.lenovo.com/support This section provides instructions on how to replace the heat sink assembly. CAUTION: The heat sink and fan assembly might be very hot. Turn off the computer and wait three to five minutes to let the computer cool before removing the computer cover. To replace the heat sink assembly, do the following: 1. Remove all media from the drives and turn off all attached devices and the computer.
9. Follow the sequence 1 , 2 , 3 , 4 on the heat sink assembly to tighten the four screws to secure the heat sink assembly to the system board, as shown in Figure 27 “Loosing the four screws that secure the heat sink assembly to the system board” on page 102. 10. Reinstall the system board shield. See “Removing and reinstalling the system board shield” on page 98. 11. Go to “Completing the parts replacement” on page 121.
Figure 28. Opening the retainer to access the microprocessor 8. Lift the microprocessor straight up and out of the socket. Notes: a. Your microprocessor and socket might look different from the one illustrated. b. Note the orientation of the microprocessor in the socket. You can either look for the small triangle 1 on one corner of the microprocessor or note the orientation of the notches 2 on the microprocessor. This is important when installing a new microprocessor on the system board. Figure 29.
Figure 30. Removing the microprocessor 9. Make sure that the small handle is in the raised position and the microprocessor retainer is fully open. 10. Hold the new microprocessor and align the notches 2 on it with the alignment keys in the microprocessor socket, or align the small triangle 1 on one corner of the new microprocessor with the corresponding beveled corner of the microprocessor socket. Figure 31. Installing the microprocessor 11.
Replacing the card reader Attention Do not open your computer or attempt any repair before reading and understanding the “Important safety information” in the ThinkCentre Edge Safety and Warranty Guide that came with your computer. To obtain a copy of the ThinkCentre Edge Safety and Warranty Guide, go to: http://www.lenovo.com/support This section provides instructions on how to replace the card reader. Note: The card reader is available only in some models. To replace the card reader, do the following: 1.
10. Reinstall the system board shield. See “Removing and reinstalling the system board shield” on page 98. 11. Go to “Completing the parts replacement” on page 121. Opening the system board shield window Attention Do not open your computer or attempt any repair before reading and understanding the “Important safety information” in the ThinkCentre Edge Safety and Warranty Guide that came with your computer. To obtain a copy of the ThinkCentre Edge Safety and Warranty Guide, go to: http://www.lenovo.
Replacing the battery Attention Do not open your computer or attempt any repair before reading and understanding the “Important safety information” in the ThinkCentre Edge Safety and Warranty Guide that came with your computer. To obtain a copy of the ThinkCentre Edge Safety and Warranty Guide, go to: http://www.lenovo.com/support This section provides instructions on how to replace the battery.
Figure 35. Installing a new battery 8. Reinstall the system board shield or close the system board shield window. See “Removing and reinstalling the system board shield” on page 98 or “Opening the system board shield window” on page 107. 9. Reinstall the computer cover. See “Completing the parts replacement” on page 121. 10. Turn on the computer and all attached devices. Note: When you turn the computer for the first time after replacing the battery, an error message might be displayed.
7. Disconnect the three cables from the inverter. 8. Lift the inverter off the computer. 9. To reinstall the new inverter, connect the three cables to the new inverter. Position the new inverter and align the two screw holes in the new inverter with those in the computer. 10. Install the two screws to secure the new inverter to the main bracket. 11. Reinstall the optical drive. See “Replacing the optical drive” on page 94. 12. Go to “Completing the parts replacement” on page 121.
3. Remove the computer cover. See “Removing the computer cover” on page 91. 4. Locate the memory slots on the system board. See “FRU locations” on page 82. 5. Remove the system board shield or open the system board shield window to get access to the battery. See “Removing and reinstalling the system board shield” on page 98 or “Opening the system board shield window” on page 107. 6. Remove any parts and disconnect any cables that might prevent your access to the memory slots. 7.
Replacing the internal speakers Attention Do not open your computer or attempt any repair before reading and understanding the “Important safety information” in the ThinkCentre Edge Safety and Warranty Guide that came with your computer. To obtain a copy of the ThinkCentre Edge Safety and Warranty Guide, go to: http://www.lenovo.com/support This section provides instructions on how to replace the internal speakers. To replace the internal speakers, do the following: 1.
Replacing the integrated camera Attention Do not open your computer or attempt any repair before reading and understanding the “Important safety information” in the ThinkCentre Edge Safety and Warranty Guide that came with your computer. To obtain a copy of the ThinkCentre Edge Safety and Warranty Guide, go to: http://www.lenovo.com/support This section provides instructions on how to replace the integrated camera. Note: The integrated camera is available only in some models.
10. Route the new integrated camera cable, and then connect the integrated camera cable to the system board. See “System board parts and connectors” on page 84. 11. Reinstall the system board shield. See “Removing and reinstalling the system board shield” on page 98. 12. Go to “Completing the parts replacement” on page 121.
Figure 40. Removing the seven screws that secure the system board to the main bracket 13. Place the new system board into the chassis and align the screw holes with those in the chassis. 14. Reinstall the seven screws that secure the system board to the main bracket. 15. Reinstall the rear I/O assembly. See “Replacing the rear I/O assembly” on page 96. 16. Reinstall the battery. See “Replacing the battery” on page 108. 17. Reinstall the memory modules.
Figure 41. Installing one side of the socket cover into the microprocessor socket Note: Your microprocessor socket and cover might look slightly different from the illustration. 4. Carefully press the other side of the socket cover downwards until the socket cover snaps into place. 5. Carefully check the four corners of the socket cover to make sure that the cover is secured in the microprocessor socket. 6. Lower the microprocessor retainer, and then lower the lever to secure the retainer.
Figure 42. Removing the foot stands 5. Locate the LCD panel in the computer. See “FRU locations” on page 82. 6. Remove the optical drive. See “Replacing the optical drive” on page 94. 7. Remove the inverter. See “Replacing the inverter” on page 109. 8. Remove the rear I/O assembly. See “Replacing the rear I/O assembly” on page 96. 9. Remove the system board shield. See “Removing and reinstalling the system board shield” on page 98. 10. Disconnect the LCD panel cable from the system board.
11. Remove all the 15 screws that secure the computer main bracket to the front bezel. Figure 44. Removing all the 15 screws that secure the computer main bracket to the front bezel 12. Note the locations of all cable connections that prevent you from lifting the computer main bracket, and disconnect all cables. See “System board parts and connectors” on page 84. 13. Remove the integrated camera. See “Replacing the integrated camera” on page 113 14. Lift the computer main bracket off the front bezel. 15.
Figure 46. Reinstalling all the 15 screws that secure the computer main bracket to the front bezel 19. Reconnect the LCD panel cable to the system board. See Figure 47. Reconnect the LCD panel cable to the system board 20. Reinstall the integrated camera. See “Replacing the integrated camera” on page 113. 21. Reinstall the rear I/O assembly. See “Replacing the rear I/O assembly” on page 96. 22. Reinstall the system board shield. See “Removing and reinstalling the system board shield” on page 98. 23.
Replacing the WI-FI card Attention Do not open your computer or attempt any repair before reading and understanding the “Important safety information” in the ThinkCentre Safety and Warranty Guide that came with your computer. To obtain a copy of the ThinkCentre Safety and Warranty Guide, go to: http://www.lenovo.com/support This section provides instructions on how to replace the WI-FI card. Note: The WI-FI card is available only in some models. To replace the WI-FI card, do the following: 1.
Figure 49. Removing the WI-FI card 9. Insert the notched end of the new WI-FI card into the mini PCI Express slot. Press the new WI-FI card firmly, and then pivot the WI-FI card to align the screw hole in the new WI-FI card with that in the system board. 10. Install the screw to secure the new WI-FI card to the system board. 11. Connect the two cables to the new WI-FI card. 12. Reinstall the rear I/O assembly. See “Replacing the rear I/O assembly” on page 96. 13. Reinstall the system board shield.
3. Lower and position the computer cover into place and then tighten the two screws 1 to secure the computer cover. Figure 50. Installing the computer cover 4. Reinstall the system stand and system stand hinge cover. See “Removing and reinstalling the system stand” on page 86 and “Removing and reinstalling the system stand hinge cover” on page 85. 5. Lock the computer cover if you have an integrated cable lock. 6. Reconnect the external cables and power cord to the computer. 7.
Chapter 9. FRU lists This chapter lists the information on the field replaceable units (FRUs). Attention: Be sure to read and understand all the safety information before replacing any FRUs. Note: In the following tables, a customer replaceable unit (CRU) is identified as “1,” “2,” or “N” in the CRU column. “N” means that the part is not a CRU, “1” means that the part is a Self-service CRU, and “2” means that the part is an Optional-service CRU.
Item # FRUs FRU # CRU 03T9679 N 03T9654 N 03T8011 N 03T8010 N 03T8017 N 03T8016 N 03T6226 N 03T6225 N System stand, assembly frame stand, non-touch 2 • MT 5068: all models • MT 7558: all models • MT 7567: all models FRU, assembly system board shielding 5 • MT 5068: all models • MT 7558: all models • MT 7567: all models Microprocessor, Ci3 2100 Sandy bridge 3MB 2c FCLGA 3.
Item # FRUs FRU # CRU 03T6224 N 03T8015 N 03T8358 N 03T8361 N 03T8360 N 03T8354 N 03T8356 N 03T8355 N 64Y6650 N Microprocessor, G850 Sandy bridge 3MB 2c FCLGA 2.9GHz 65W HD graphics 8 • MT 5068: CTO • MT 7558: CTO • MT 7567: CTO Microprocessor, Ci7 2600S Sandy bridge 8MB 4c FCLGA 2.8GHZ 65W vPro 8 • MT 5068: CTO • MT 7558: CTO • MT 7567: CTO Microprocessor, Ci3-2130,3.40GHz/3M/65W,dual core 8 • MT 5068: CTO • MT 7558: CTO • MT 7567: CTO Microprocessor, Pentium G860, 3.
Item # FRUs FRU # CRU 64Y6651 N 89Y9225 N 03T9028 N 03T9025 N 03T9680 N Memory module, 2GB PC3-10600 1333MHz DDR3 SoDIMM • MT 5068: CTO A1G A2G A3G A4G A5G A6G A7G A8G • MT 7558: CTO A1B A2B A3B A3V A4B A5B B9S B9D B9Y C1S C1D C1Y C2S C2D C2Y C3J C4J A6G A7G B4V B6V B7V B8V C7J C8J C9J D1J D2J D3J D4Q D5Q D6Q E4Q E6Q E7Q G1S G1D G1Y G3G G4G G5B H2B H7T H8A H1B G6Q G9Q 9 • MT 7567: CTO A5S A5D A5Y A6S A6D A6Y A7J A8J A9J B1J B2J B4J B5J B6J B7J B8A B9A C1A C2A C3A C4A C5A C5T C6A C6T C7A C7T
Item # FRUs FRU # CRU 03T9022 N 40Y9036 N 45K0408 N 87H4891 N 45K0409 N 45K0410 N Power supply, 150w 85+ AIO PSU • MT 5068: CTO A1G A2G A3G A4G A5G A6G A7G A8G A9G B1G B2G B3G B4G B5G B6G B7G B8G 17 • MT 7558: CTO A1B A2B A3B A3V A4B A5B B9S B9D B9Y C1S C1D C1Y C2S C2D C2Y C3J C4J C5J C6J B5G A6G A7G A8G A9G B1G B2G B3G B4V B6V B7V B8V C7J C8J C9J D1J D2J D3J D4Q D5Q D6Q D7Q D8Q D9Q E1Q E2Q E3Q E4Q E5Q E6Q E7Q E8Q E9Q F1Q F2Q F3Q F4Q F5Q G1S G1D G1Y G2S G2D G2Y G3G G4G G5B H2B H7T H8A H4G
Item # FRUs FRU # CRU 03T7041 N 45K0412 N 03T7042 N 45K0616 N 03T7039 N 03T7040 N 03T7041 N 03T7042 N Hard disk drive, SATA 500GB 7200RPM/3Gb/16M • MT 5068: CTO A1G A3G A6G A7G A8G A9G B1G B2G B3G B4G B5G B6G B7G B8G 22 • MT 7558: CTO A1B A2B A3B A3V A4B A5B B9S B9D B9Y C1S C1D C1Y C2S C2D C2Y B5G A6G A7G A8G A9G B1G B2G B3G B4V B6V B7V B8V D4Q D5Q D6Q D7Q D8Q D9Q E1Q E2Q E3Q E4Q E5Q E6Q E7Q E8Q E9Q F1Q F2Q F3Q F4Q F5Q G1S G1D G1Y G2S G2D G2Y G5B H2B H7T H8A H4G H1B G6Q G7Q G8Q G9Q H5V
Item # FRUs FRU # CRU 03T6429 N 03T6431 N 03T6434 N 71Y5848 N 45K0433 N FRU # CRU 03T9647 N 03T9650 N LCD panel, 20inch 1600x900 CCFL panel 24 • MT 5068: all models • MT 7558: all models • MT 7567: all models LCD panel, 20inch 1600x900 CCFL panel 24 • MT 5068: all models • MT 7558: all models • MT 7567: all models Inverter 25 • MT 5068: all models • MT 7558: all models • MT 7567: all models Optical drive, SATA slim DVD-ROM 26 • MT 5068: CTO • MT 7558: CTO C3J C5J B6V B8V C7J C9J D
FRUs FRU # CRU 03T9643 N 03T9645 N 03T9646 N 03T9642 N 03T9651 N 03T9653 N 03T9655 N 03T6439 N 03T9682 N FRU, cables • MT 5068: all models • MT 7558: all models • MT 7567: all models FRU, card reader bezel • MT 5068: all models • MT 7558: all models • MT 7567: all models FRU, card reader blank bezel • MT 5068: all models • MT 7558: all models • MT 7567: all models FRU, ODD bezel kits • MT 5068: all models • MT 7558: all models • MT 7567: all models FRU, front bezel assembly without came
FRUs FRU # CRU 03T9681 N 03T9684 N FRU # CRU 60Y3241 N 03T9015 N 43N9160 N FRU # CRU 54Y9293 1 54Y9294 1 54Y9295 1 FRU, assembly panel bracket • MT 5068: all models • MT 7558: all models • MT 7567: all models FRU, screw kits • MT 5068: all models • MT 7558: all models • MT 7567: all models Adapters and miscellaneous FRUs Adapters and miscellaneous FRUs Intel-1000 wireless condor peak • MT 5068: CTO • MT 7558: CTO • MT 7567: CTO BCM BCM43227 2x2 MC • MT 5068: CTO • MT 7558: CTO • MT 7
Keyboard (Lenovo Slim New F5 USB) FRU # CRU 54Y9296 1 54Y9297 1 54Y9298 1 54Y9299 1 54Y9300 1 54Y9301 1 54Y9302 1 54Y9303 1 54Y9304 1 Slim New F5 USB--B/F • MT 5068: CTO A2G A3G A4G A5G A6G A7G A8G A9G B1G B2G B3G B4G B5G B6G B7G B8G • MT 7558: CTO B5G A6G A7G A8G A9G B1G B2G B3G G3G G4G H4G H3G • MT 7567: CTO E5G E6G E7G E8G Slim New F5 USB--Belgium English • MT 5068: CTO A2G A3G A4G A5G A6G A7G A8G A9G B1G B2G B3G B4G B5G B6G B7G B8G • MT 7558: CTO B5G A6G A7G A8G A9G B1G B2G B3G G3G
Keyboard (Lenovo Slim New F5 USB) FRU # CRU 54Y9305 1 54Y9306 1 54Y9307 1 54Y9308 1 54Y9309 1 54Y9310 1 54Y9311 1 54Y9312 1 54Y9313 1 Slim New F5 USB--French Canadian • MT 5068: CTO • MT 7558: CTO • MT 7567: CTO Slim New F5 USB--French Canadian • MT 5068: CTO • MT 7558: CTO • MT 7567: CTO Slim New F5 USB--German • MT 5068: CTO A2G A3G A4G A5G A6G A7G A8G A9G B1G B2G B3G B4G B5G B6G B7G B8G • MT 7558: CTO B5G A6G A7G A8G A9G B1G B2G B3G G3G G4G H4G H3G • MT 7567: CTO E5G E6G E7G E8G Slim
Keyboard (Lenovo Slim New F5 USB) FRU # CRU 54Y9314 1 54Y9315 1 54Y9316 1 54Y9317 1 54Y9318 1 54Y9319 1 54Y9320 1 54Y9321 1 54Y9322 1 Slim New F5 USB--Japanese • MT 5068: CTO • MT 7558: CTO • MT 7567: CTO Slim New F5 USB--Korean • MT 5068: CTO • MT 7558: CTO • MT 7567: CTO Slim New F5 USB--LA Spanish • MT 5068: CTO • MT 7558: CTO B9S B9D B9Y C1S C1D C1Y C2S C2D C2Y G1S G1D G1Y G2S G2D G2Y • MT 7567: CTO A5S A5D A5Y A6S A6D A6Y E1S E1D E1Y E2S E2D E2Y Slim New F5 USB--Norwegian • MT 5068
Keyboard (Lenovo Slim New F5 USB) FRU # CRU 54Y9323 1 54Y9324 1 54Y9325 1 54Y9326 1 54Y9327 1 54Y9328 1 54Y9329 1 54Y9330 1 Slim New F5 USB--Slovak • MT 5068: CTO A2G A3G A4G A5G A6G A7G A8G A9G B1G B2G B3G B4G B5G B6G B7G B8G • MT 7558: CTO B5G A6G A7G A8G A9G B1G B2G B3G G3G G4G H4G H3G • MT 7567: CTO E5G E6G E7G E8G Slim New F5 USB--Spanish • MT 5068: CTO A2G A3G A4G A5G A6G A7G A8G A9G B1G B2G B3G B4G B5G B6G B7G B8G • MT 7558: CTO B5G A6G A7G A8G A9G B1G B2G B3G G3G G4G H4G H3G • MT
Keyboard (Lenovo Slim New F5 USB) FRU # CRU 54Y9331 1 54Y9332 1 54Y9333 1 54Y9334 1 54Y9335 1 54Y8380 1 FRU # CRU 03X8201 1 03X8202 1 Slim New F5 USB--US European • MT 5068: CTO A2G A3G A4G A5G A6G A7G A8G A9G B1G B2G B3G B4G B5G B6G B7G B8G • MT 7558: CTO B5G A6G A7G A8G A9G B1G B2G B3G G3G G4G H4G H3G • MT 7567: CTO E5G E6G E7G E8G Slim New F5 USB--Slovenian • MT 5068: CTO A2G A3G A4G A5G A6G A7G A8G A9G B1G B2G B3G B4G B5G B6G B7G B8G • MT 7558: CTO B5G A6G A7G A8G A9G B1G B2G B3G G3
Keyboard (Wireless Edge keyboard and mouse) FRU # CRU 03X8203 1 03X8204 1 03X8205 1 03X8206 1 03X8207 1 03X8208 1 03X8209 1 03X8210 1 03X8211 1 03X8212 1 Wireless Edge --A/F • MT 5068: CTO • MT 7558: CTO • MT 7567: CTO Wireless Edge --B/F • MT 5068: CTO • MT 7558: CTO G3G G4G • MT 7567: CTO Wireless Edge --Belgium English • MT 5068: CTO • MT 7558: CTO G3G G4G • MT 7567: CTO Wireless Edge --Brazilian Portuguese • MT 5068: CTO • MT 7558: CTO • MT 7567: CTO Wireless Edge --Bulgarian • MT
Keyboard (Wireless Edge keyboard and mouse) FRU # CRU 03X8213 1 03X8214 1 03X8215 1 03X8216 1 03X8217 1 03X8218 1 03X8219 1 03X8220 1 03X8221 1 03X8222 1 Wireless Edge --French Canadian • MT 5068: CTO • MT 7558: CTO • MT 7567: CTO Wireless Edge --French Canadian • MT 5068: CTO • MT 7558: CTO • MT 7567: CTO Wireless Edge --German • MT 5068: CTO • MT 7558: CTO G3G G4G • MT 7567: CTO Wireless Edge --Greek • MT 5068: CTO • MT 7558: CTO G3G G4G • MT 7567: CTO Wireless Edge --Greek/US • MT
Keyboard (Wireless Edge keyboard and mouse) FRU # CRU 03X8223 1 03X8224 1 03X8225 1 03X8226 1 03X8227 1 03X8228 1 03X8229 1 03X8230 1 03X8231 1 03X8232 1 Wireless Edge --Korean • MT 5068: CTO • MT 7558: CTO • MT 7567: CTO Wireless Edge --LA Spanish • MT 5068: CTO • MT 7558: CTO • MT 7567: CTO Wireless Edge --Norwegian • MT 5068: CTO • MT 7558: CTO G3G G4G • MT 7567: CTO Wireless Edge --Polish • MT 5068: CTO • MT 7558: CTO G3G G4G • MT 7567: CTO Wireless Edge --Portuguese • MT 5068: CT
Keyboard (Wireless Edge keyboard and mouse) FRU # CRU 03X8233 1 03X8234 1 03X8235 1 03X8236 1 03X8237 1 03X8239 1 FRU # CRU 41A5289 1 41A5290 1 41A5291 1 Wireless Edge --Thailand • MT 5068: CTO • MT 7558: CTO • MT 7567: CTO C5T C7T C9T Wireless Edge --Turkish • MT 5068: CTO • MT 7558: CTO G3G G4G • MT 7567: CTO Wireless Edge --UK English • MT 5068: CTO • MT 7558: CTO G3G G4G • MT 7567: CTO Wireless Edge --US European • MT 5068: CTO • MT 7558: CTO G3G G4G • MT 7567: CTO Wireless Edge -
Keyboard (Preferred professional fullsize USB) FRU # CRU 41A5292 1 41A5293 1 41A5294 1 41A5295 1 41A5296 1 41A5297 1 41A5298 1 41A5299 1 41A5300 1 41A5301 1 Preferred Pro Fullsize USB--B/F • MT 5068: CTO • MT 7558: CTO • MT 7567: CTO Preferred Pro Fullsize USB--Belgium English • MT 5068: CTO • MT 7558: CTO • MT 7567: CTO Preferred Pro Fullsize USB--Brazilian Portuguese • MT 5068: CTO • MT 7558: CTO • MT 7567: CTO Preferred Pro Fullsize USB--Bulgarian • MT 5068: CTO • MT 7558: CTO • MT
Keyboard (Preferred professional fullsize USB) FRU # CRU 41A5302 1 41A5303 1 41A5304 1 41A5305 1 41A5306 1 41A5307 1 41A5308 1 41A5309 1 41A5310 1 41A5311 1 Preferred Pro Fullsize USB--French Canadian • MT 5068: CTO • MT 7558: CTO • MT 7567: CTO Preferred Pro Fullsize USB--German • MT 5068: CTO • MT 7558: CTO • MT 7567: CTO Preferred Pro Fullsize USB--Greek • MT 5068: CTO • MT 7558: CTO • MT 7567: CTO Preferred Pro Fullsize USB--Greek/US • MT 5068: CTO • MT 7558: CTO • MT 7567: CTO Pr
Keyboard (Preferred professional fullsize USB) FRU # CRU 41A5312 1 41A5313 1 41A5314 1 41A5315 1 41A5316 1 41A5317 1 41A5318 1 41A5319 1 41A5320 1 41A5321 1 Preferred Pro Fullsize USB--LA Spanish • MT 5068: CTO • MT 7558: CTO • MT 7567: CTO Preferred Pro Fullsize USB--Norwegian • MT 5068: CTO • MT 7558: CTO • MT 7567: CTO Preferred Pro Fullsize USB--Polish • MT 5068: CTO • MT 7558: CTO • MT 7567: CTO Preferred Pro Fullsize USB--Portuguese • MT 5068: CTO • MT 7558: CTO • MT 7567: CTO P
Keyboard (Preferred professional fullsize USB) FRU # CRU 41A5322 1 41A5323 1 41A5324 1 41A5325 1 41A5326 1 41A5327 1 41A5328 1 41A5329 1 45J4880 1 Preferred Pro Fullsize USB--Swedish/Finnish • MT 5068: CTO • MT 7558: CTO • MT 7567: CTO Preferred Pro Fullsize USB--SF/G • MT 5068: CTO • MT 7558: CTO • MT 7567: CTO Preferred Pro Fullsize USB--Thailand • MT 5068: CTO • MT 7558: CTO H7T • MT 7567: CTO C6T C8T Preferred Pro Fullsize USB--Turkish • MT 5068: CTO • MT 7558: CTO • MT 7567: CTO Pr
Keyboard (Preferred professional fullsize USB) FRU # CRU 45J4896 1 54Y8381 1 FRU # CRU 45J4889 1 FRU # CRU 41R3184 1 Preferred Pro Fullsize USB--Lithuanian • MT 5068: CTO • MT 7558: CTO • MT 7567: CTO Preferred Pro Fullsize USB--India • MT 5068: CTO • MT 7558: CTO • MT 7567: CTO Mice Lenovo enhanced optical USB mouse • MT 5068: CTO A1G A2G A3G A4G A5G A6G A7G A8G A9G B1G B2G B3G B4G B5G B6G B7G B8G • MT 7558: CTO A1B A2B A3B A3V A4B A5B B9S B9D B9Y C1S C1D C1Y C2S C2D C2Y C3J C4J C5J C6J B5G
Power Cords --primary FRU # CRU 45J9595 1 41R3176 1 41R3196 1 41R3260 1 41R3224 1 41R3278 1 41R3232 1 41R3212 1 Line Cord - Brazil • MT 5068: CTO • MT 7558: CTO H3P • MT 7567: CTO F7P F8P F9P Line Cord - LA (High Voltage) Argentina, Paraguay, Uruguay • MT 5068: CTO • MT 7558: CTO B9Y C1Y C2Y G1Y G2Y • MT 7567: CTO A5Y A6Y E1Y E2Y Line Cord - ANZ.
Power Cords --primary FRU # CRU 41R3228 1 41R3236 1 41R3220 1 41R3341 1 41R3208 1 FRU # CRU 41R3185 1 41R3257 1 Line Cord - Switzerland, Liechtenstein • MT 5068: CTO A1G A2G A3G A4G A5G A6G A7G A8G A9G B1G B2G B3G B4G B5G B6G B7G B8G • MT 7558: CTO B5G A6G A7G A8G A9G B1G B2G B3G G3G G4G H4G H3G • MT 7567: CTO E5G E6G E7G E8G Line Cord - Israel • MT 5068: CTO A1G A2G A3G A4G A5G A6G A7G A8G A9G B1G B2G B3G B4G B5G B6G B7G B8G • MT 7558: CTO B5G A6G A7G A8G A9G B1G B2G B3G G3G G4G H4G H3G
Power Cords --secondary FRU # CRU 41R3249 1 41R3271 1 41R3177 1 41R3197 1 41R3261 1 41R3225 1 41R3279 1 41R3233 1 • MT 7567: CTO Line Cord - Japan • MT 5068: CTO • MT 7558: CTO C3J C4J C5J C6J C7J C8J C9J D1J D2J D3J • MT 7567: CTO A7J A8J A9J B1J B2J B4J B5J B6J B7J Line Cord - Brazil • MT 5068: CTO • MT 7558: CTO H3P • MT 7567: CTO F7P F8P F9P Line Cord - LA (High Voltage) Argentina, Paraguay, Uruguay • MT 5068: CTO • MT 7558: CTO B9Y C1Y C2Y G1Y G2Y • MT 7567: CTO A5Y A6Y E1Y E2Y Line
Power Cords --secondary FRU # CRU 41R3213 1 41R3229 1 41R3237 1 41R3221 1 41R3175 1 41R3209 1 Line Cord - Denmark • MT 5068: CTO A1G A2G A3G A4G A5G A6G A7G A8G A9G B1G B2G B3G B4G B5G B6G B7G B8G • MT 7558: CTO B5G A6G A7G A8G A9G B1G B2G B3G G3G G4G H4G H3G • MT 7567: CTO E5G E6G E7G E8G Line Cord - Switzerland, Liechtenstein • MT 5068: CTO A1G A2G A3G A4G A5G A6G A7G A8G A9G B1G B2G B3G B4G B5G B6G B7G B8G • MT 7558: CTO B5G A6G A7G A8G A9G B1G B2G B3G G3G G4G H4G H3G • MT 7567: CTO E5G E6
150 ThinkCentre Edge Hardware Maintenance Manual
Chapter 10. Additional Service Information This chapter provides additional information that the service representative might find helpful. Security features Security features in this section include the following: • Passwords • Vital Product Data • Management Information Format (MIF) Hardware controlled Passwords Hardware controlled passwords are set using the Setup Utility program. For more information about passwords, see “Using passwords” on page 53.
Note: You can download a self-starting bootable disc image (known as an ISO image) with the system program updates to create a system-program-update disc. Go to: http://www.lenovo.com/support To update (flash) the BIOS from a disc, do the following: 1. Turn off your computer. 2. Repeatedly press and release the F12 key when turning on the computer. When the Startup Device Menu window opens, release the F12 key. 3. On the Startup Device Menu window, select the desired optical drive as the startup device.
4. Move the jumper from the standard position (pin 1 and pin 2) to the maintenance position (pin 2 and pin 3). 5. Install the computer cover and reconnect all cables and power cords that were disconnected. See “Completing the parts replacement” on page 121. 6. Repeatedly press and release the F12 key when turning on the computer. When the Startup Device Menu opens, release the F12 key. 7. Insert the POST/BIOS update (flash) disc into the optical drive.
154 ThinkCentre Edge Hardware Maintenance Manual
Appendix A. Notices Lenovo may not offer the products, services, or features discussed in this document in all countries. Consult your local Lenovo representative for information on the products and services currently available in your area. Any reference to a Lenovo product, program, or service is not intended to state or imply that only that Lenovo product, program, or service may be used.
Television output notice The following notice applies to models that have the factory-installed television-output feature. This product incorporates copyright protection technology that is protected by method claims of certain U.S. patents and other intellectual property rights owned by Macrovision Corporation and other rights owners.
Index A Administrator, password installing, replacing memory module 110 integrated camera, replacing 113 internal speakers, replacing 112 inverter, replacing 109 54 B basic troubleshooting 33 battery, replacing 108 boot-block recovery 152 L LCD panel, replacing 116 Lenovo ThinkVantage Toolbox Lenovo Welcome 29 C card reader, replacing 106 changing password 54 startup device sequence 55 computer cover removing 91 computer cover, reinstalling 121 connectors rear 81 connectors, controls, indicators front
removing the system stand hinge cover replacing battery 108 card reader 106 hard disk drive 92 heat sink assembly 101 integrated camera 113 internal speakers 112 inverter 109 LCD panel 116 microprocessor fan 100 power supply 99 rear I/O assembly 96 system board 114 WI-FI card 120 resources, information 29 85 VESA mount bracket, removing 95 viewing and changing settings 53 W WI-FI card, replacing 107 T television output notice 156 temporary startup device 55 the BIOS, updating (flashing) 151–152 tradema
Part Number: 0B03379 Printed in USA (1P) P/N: 0B03379 *0B03379*
