User Guide Types 8288, 8297, 8326 Types 8329, 8342, 8380
User Guide Types 8288, 8297, 8326 Types 8329, 8342, 8380
Note Before using this information and the product it supports, be sure to read the “Important safety information” on page v and Appendix D, “Notices,” on page 43. Seond Edition (January 2006) © Copyright Lenovo 2006. Portions © Copyright International Business Machines Corporation 2005. All rights reserved. U.S. GOVERNMENT USERS – RESTRICTED RIGHTS: Our products and/or services are provided with RESTRICTED RIGHTS.
Contents Important safety information . . . . . . v Conditions that require immediate action . . . . . v General safety guidelines . . . . . . . . . . vi Service . . . . . . . . . . . . . . . vi Power cords and power adapters . . . . . . vii Extension cords and related devices . . . . . viii Plugs and outlets . . . . . . . . . . . viii Batteries . . . . . . . . . . . . . . viii Heat and product ventilation . . . . . . . ix CD and DVD drive safety . . . . . . . . . ix Additional safety information. . . . . .
iv User Guide
Important safety information Note Please read important safety information first. This information can help you safely use your desktop or notebook personal computer. Follow and retain all information included with your computer. The information in this document does not alter the terms of your purchase agreement or the Lenovo™ Statement of Limited Warranty. Customer safety is important. Our products are developed to be safe and effective. However, personal computers are electronic devices.
speak to the Customer Support Center for further guidance. See “Information resources” on page xiii for more information. v Power cords, plugs, power adapters, extension cords, surge protectors, or power supplies that are cracked, broken or damaged. v Signs of overheating, smoke, sparks or fire. v Damage to a battery (such as cracks, dents, creases), discharge from a battery, or a buildup of foreign substances on the battery.
Danger Hazardous moving parts. Keep fingers and other body parts away. Attention Before replacing any CRUs, turn off the computer and wait three to five minutes to let the computer cool before opening the cover. Power cords and power adapters Use only the power cords and power adapters supplied by the product manufacturer. The power cords shall be safety approved. For Germany, it shall be H05VV-F, 3G, 0.75 mm2, or better. For other countries, the suitable types shall be used accordingly.
Extension cords and related devices Ensure that extension cords, surge protectors, uninterruptible power supplies, and power strips that you use are rated to handle the electrical requirements of the product. Never overload these devices. If power strips are used, the load should not exceed the power strip input rating. Consult an electrician for more information if you have questions about power loads, power requirements, and input ratings.
shorten the life of the battery and can also pose a safety hazard. Do not let rechargeable Lithium-Ion batteries completely discharge or store these batteries in a discharged state. Heat and product ventilation Computers generate heat when turned on and when batteries are charging. Notebook PCs can generate a significant amount of heat due to their compact size.
v Do not bend or flex CD/DVD discs, or force them into the computer or their packaging v Check CD/DVD discs for cracks before each use. Do not use cracked or damaged discs Additional safety information Danger Electrical current from power, telephone, and communication cables is hazardous. To avoid a shock hazard: v Do not connect or disconnect any cables or perform installation, maintenance, or reconfiguration of this product during an electrical storm.
Dispose of the battery as required by local ordinances or regulations. Modem safety information Caution To reduce the risk of fire, use only No. 26 AWG or larger telecommunication line cord. To reduce the risk of fire, electrical shock, or injury when using telephone equipment, always follow basic safety precautions, such as: v Never install telephone wiring during a lightning storm. v Never install telephone jacks in wet locations unless the jack is specifically designed for wet locations.
Power supply statement Never remove the cover on a power supply or any part that has the following label attached. Hazardous voltage, current, and energy levels are present inside any component that has this label attached. There are no serviceable parts inside these components. If you suspect a problem with one of these parts, contact a service technician.
Overview Thank you for selecting this computer. Your computer incorporates many of the latest advances in computer technology and can be upgraded as your needs change. Adding hardware options to your computer is an easy way to increase its capabilities. Instructions for installing external and internal options are included in this publication. When adding an option, use these instructions along with the instructions that come along with the option.
xiv User Guide
Chapter 1. Installing options This chapter provides an introduction to the features and options that are available for your computer. You can expand the capabilities of your computer by adding memory, adapters, or drives. When installing an option, use these instructions along with the instructions that come with the option. Note: Use only parts provided by Lenovo. Important Before you install or remove any option, read “Important safety information” on page v.
v Intel Pentium 4 processor v Intel Celeron® D processor v Internal cache (size varies by model type) Memory v Support for two double data rate 2 (DDR2) dual inline memory modules (DIMM) v 512 KB flash memory for system programs Internal drives v 3.5-inch, slim, 1.
Expansion v Four drive bays v Two standard peripheral component interconnect (PCI) adapter connectors v One PCI Express x1 adapter connector Power v 230 W power supply with manual voltage selection switch (some models) v Automatic 50/60 Hz input frequency switching v Advanced Configuration and Power Interface (ACPI) support Security features v Keyboard with fingerprint reader (some models, use the ThinkVantage Productivity Center program to find more information) v User and administrator passwords for BIOS
Specifications This section lists the physical specifications for your computer. Dimensions Height: 400 mm (15.7 in.) Width: 175 mm (6.9 in.) Minimum configuration: 246 Btu/hr (76 watts) Depth: 432 mm (17.0 in.) Maximum configuration: 785 Btu/hr (230 watts) Airflow Weight Minimum configuration: 8.17 kg (18 lb) Maximum configuration: 10.21 kg (22.
Available options The following are some available options: v External options – Parallel port devices, such as printers and external drives – Serial port devices, such as external modems and digital cameras – Audio devices, such as external speakers for the sound system – USB devices, such as printers, joysticks, and scanners – Security device, such as a padlock – Monitors v Internal options – System memory, called dual inline memory modules (DIMMs) – Peripheral component interconnect (PCI) adapters – PCI
Handling static-sensitive devices Static electricity, although harmless to you, can seriously damage computer components and options. When you add an option, do not open the static-protective package containing the option until you are instructed to do so. When you handle options and other computer components, take these precautions to avoid static electricity damage: v Limit your movement. Movement can cause static electricity to build up around you. v Always handle components carefully.
Locating the connectors on the front of your computer The following illustration shows the locations of the connectors on the front of the computer. 1 2 USB connector USB connector 3 4 Headphone connector Microphone connector Chapter 1.
Locating the connectors on the rear of your computer The following illustration shows the locations of the connectors on the rear of the computer.
Connector Description Mouse connector Used to attach a mouse, trackball, or other pointing device that uses a standard mouse connector. Keyboard connector Used to attach a keyboard that uses a standard keyboard connector. Serial connector Used to attach an external modem, serial printer, or other devices that use a 9-pin serial connector. Parallel connector Used to attach a parallel printer, parallel scanner, or other devices that use a 25-pin parallel connector.
Removing the cover Important Read “Important safety information” on page v and “Handling static-sensitive devices” on page 6 before removing the computer cover. To remove the computer cover: 1. Shut down your operating system, remove any media (diskettes, CDs, or tapes) from the drives, and turn off all attached devices and the computer. 2. Unplug all power cords from electrical outlets. 3. Disconnect all cables attached to the computer.
Locating components The following illustration will help you locate the various components in your computer. 1 2 3 Microprocessor fan and heat sink Memory modules PCI adapter card 4 5 6 PCI adapter connectors System fan Power supply Chapter 1.
Identifying parts on the system board The system board (sometimes called the planar or motherboard) is the main circuit board in your computer. It provides basic computer functions and supports a variety of devices that are factory-installed or that you can install later. The following illustration shows the locations of parts on the system board.
Installing memory Your computer has two connectors for installing dual inline memory modules (DIMMs) that provide up to a maximum of 4.0 GB of system memory. When installing memory modules, the following rules apply: v Use 1.8 V, 240-pin double data rate 2 synchronous dynamic random access memory (DDR2 SDRAM). v Use 256 MB, 512 MB, 1.0 GB, or 2.0 GB memory modules in any combination up to a maximum of 2.0 GB. To install a memory module: 1. Remove the computer cover. See “Removing the cover” on page 10. 2.
Installing adapters This section provides information and instructions for installing and removing adapters. Your computer has two expansion connectors for PCI adapters and one for a PCI Express x1 adapter. To 1. 2. 3. install an adapter: Remove the computer cover. See “Removing the cover” on page 10. Remove the screw from the adapter latch and remove the adapter latch. Remove the connector cover for the appropriate expansion connector. 4. Remove the adapter from its static-protective package. 5.
6. Install the adapter latch and insert the screw to secure the adapter. What to do next v To work with another option, go to the appropriate section. v To complete the installation, go to “Replacing the cover and connecting the cables” on page 25. Chapter 1.
Installing internal drives This section provides information and instructions for installing and removing internal drives. Internal drives are devices that your computer uses to read and store data. You can add drives to your computer to increase storage capacity and to enable your computer to read other types of media.
The following illustration shows the locations of the drive bays. The following list describes the types and size of drives you can install in each bay: 1 Bay 1 - Maximum height: 43.0 mm (1.7 in.) 2 Bay 2 - Maximum height: 43.0 mm (1.7 in.) 3 Bay 3 - Maximum height: 25.8 mm (1.0 in.) 4 Bay 4 - Maximum height: 25.8 mm (1.0 in.) v Optical drive such as CD drive or DVD drive (preinstalled in some models) v 5.25-inch hard disk drive v 3.5-inch hard disk drive (requires a Universal Adapter Bracket, 5.
Installing a drive in bay 1 or bay 2 To install a drive in bay 1 or bay 2, follow these steps: 1. Remove the computer cover. See “Removing the cover” on page 10. 2. Remove the front bezel by releasing the three plastic tabs inside the chassis and remove the bezel as shown. 3. Remove the static shield from the drive bay by using a flat-blade screwdriver to gently pry it loose.
4. Remove the plastic panel in the bezel for bay 2 by squeezing the plastic tabs that secure the panel on the inside of the bezel. 5. If you are installing any type of drive other than a serial ATA hard disk drive, make sure the drive that you are installing is set correctly as either a master or a slave device. Note: A serial ATA hard disk drive does not need to be set as either a master or a slave device. v If it is the first optical drive, set it as a master device.
Connecting drives The steps to connect a drive are different depending on the type of drive. Use one of the following procedures for your drive connection. Connecting the first optical drive 1. The drive requires two cables; a power cable that connects to the power supply and a signal cable that connects to the system board. 2. Locate the three-connector signal cable that comes with your computer or with the new drive. 3. Locate the IDE connector on the system board.
Connecting a serial ATA hard disk drive A serial hard disk drive can be connected to any available SATA connector. 1. Locate the signal cable that comes with the new drive. 2. Locate an available SATA connector on the system board. See “Identifying parts on the system board” on page 12. 3. Connect one end of the signal cable to the drive and the other to an available SATA connector on the system board. 4. Locate one of the extra five-wire power connectors and connect it to the drive.
Integrated cable lock With an integrated cable lock (sometimes referred to as the Kensington lock), you can secure your computer to a desk, table, or other non-permanent fixture. The cable lock attaches to a security slot at the rear of your computer and is operated with a key. The cable lock also locks the buttons used to open the computer cover. This is the same type of lock used with many laptop computers. You can order a security cable directly from Lenovo. Go to http://www.lenovo.
Padlock Your computer is equipped with a padlock loop such that the cover cannot be removed when a padlock is installed. Password protection To deter unauthorized use of your computer, you can use the Setup Utility program to set passwords. See “Using passwords” on page 27. What to do next v To work with another option, go to the appropriate section. v To complete the installation, go to “Replacing the cover and connecting the cables” on page 25.
To 1. 2. 3. 4. change the battery: Turn off the computer and all attached devices. Remove the computer cover. See “Removing the cover” on page 10. Locate the battery. See “Identifying parts on the system board” on page 12. Remove the old battery. 5. Install the new battery. 6. Replace the computer cover, and plug in the power cord. See “Replacing the cover and connecting the cables” on page 25.
8. Move the jumper back to the standard (pins 1 and 2). 9. Replace the computer cover and connect the power cord. See “Replacing the cover and connecting the cables.” Replacing the cover and connecting the cables After working with options, you need to install any removed parts, replace the computer cover, and reconnect any cables, including telephone lines and power cords. Also, depending on the option that is installed, you might need to confirm the updated information in the Setup Utility program.
26 User Guide
Chapter 2. Using the Setup Utility The Setup Utility program is stored in the electrically erasable programmable read-only memory (EEPROM) of your computer. The Setup Utility program is used to view and change the configuration settings of your computer, regardless of which operating system you are using. However, the operating-system settings might override any similar settings in the Setup Utility program. Starting the Setup Utility program To start the Setup Utility program, do the following: 1.
v v v v v v v Have at least eight characters in length Contain at least one alphabetic character, one numeric character, and one symbol Contain at least one of the following symbols: , .
To set Security Profile by Device, do the following: 1. Start the Setup Utility program (see “Starting the Setup Utility program” on page 27). 2. From the Setup Utility program menu, select Security. 3. Select Security Profile by Device. 4. Select the desired devices and settings and press Enter. 5. Return to the Setup Utility program menu and select Exit and then Save Settings or Save and exit the Setup Utility. Note: If you do not want to save the settings, select Exit the Setup Utility without saving.
Advanced settings On some computer models the Advanced settings menu includes a setting to Enable/Disable HyperThreading. This feature works only with HyperThreading-aware operating systems such as Microsoft Windows XP. The default setting for HyperThreading is Enabled. However, if you select Set Defaults and are using an operating system other than Windows XP, your computer performance might be degraded.
Appendix A. Updating system programs This appendix contains information about updating system programs and how to recover from a POST/BIOS update failure. System programs System programs are the basic layer of software that is built into your computer. They include the power-on self-test (POST), the basic input/output system (BIOS) code, and the Setup Utility program. POST is a set of tests and procedures that is performed each time you turn on your computer.
Updating (flashing) BIOS from your operating system Note: Due to constant improvements being made to the Lenovo Web site, Web page content (including the links referenced in the following procedure) is subject to change. 1. From your browser, type http://www.lenovo.com/support in the address field and press Enter. 2. Locate the Downloadable files for your machine type as follows: a. In the Use Quick path field, type in your machine type and click Go. b. Under Browse by product, click Continue. c.
Appendix B. Cleaning the mouse This appendix provides instructions on how to clean your mouse. The procedure will be different depending on which type of mouse you have. Cleaning an optical mouse If you experience some problems with your optical mouse, check the following: 1. Turn the mouse over and look carefully at the lens area. a. If there is a smudge on the lens, gently clean the area with a plain cotton swab. b. If there is some debris in the lens, gently blow the debris away from the area. 2.
3. Place your hand over the retainer ring and ball 2 , and then turn the mouse over, top side up, so that the retainer ring and ball fall out into your hand. 4. Wash the ball in warm, soapy water then dry it with a clean cloth. Blow air carefully into the ball cage 4 to dislodge dust and lint. 5. Look for a build up of dirt on the plastic rollers 3 inside the ball cage. This build up usually appears as a stripe running across the middle of the rollers. 6.
Appendix C. Manual modem commands The following section lists commands for manually programming your modem. Commands are accepted by the modem while it is in Command Mode. Your modem is automatically in Command Mode until you dial a number and establish a connection. Commands can be sent to your modem from a PC running communication software or any other terminal devices. All commands sent to the modem must begin with AT and end with ENTER.
Command Function H1 Force modem off-hook (make busy) Note: H1 command is not supported for Italy I_ L_ M_ I0 Display product-identification code I1 Factory ROM checksum test I2 Internal memory test I3 Firmware ID I4 Reserved ID L0 Low speaker volume L1 Low speaker volume L2 Medium speaker volume L3 High speaker volume M0 Internal speaker off M1 Internal speaker on until carrier detected M2 Internal speaker always on M3 Internal speaker on until carrier detected and off while d
Extended AT commands Command Function &C0 Force Carrier Detect Signal High (ON) &C1 Turn on CD when remote carrier is present &D0 Modem ignores the DTR signal &D1 Modem returns to Command Mode after DTR toggle &D2 Modem hangs up, returns to the Command Mode after DTR toggle &D3 Resets modem after DTR toggle &F_ &F Recall factory default configuration &G_ &G0 Guard tone disabled &G1 Guard tone disabled &G2 1800 Hz guard tone &K0 Disable flow control &K3 Enable RTS/CTS hardware flow
Command Function &W_ %E_ &V1 Display Last Connection Statistics &W0 Stores the active profile as Profile 0 &W1 Stores the active profile as Profile 1 %E0 Disable auto-retrain %E1 Enable auto-retrain +MS? Displays the current Select Modulation settings +MS=? Displays a list of supported Select Modulation options +MS=a,b,c,e,f Select modulation where: a=0, 1, 2, 3, 9, 10, 11, 12, 56, 64, 69; b=0-1; c=300-56000; d=30056000; e=0-1; and f=0-1. A, b, c, d, e, f default=12, 1, 300, 56000, 0, 0.
Fax Class 1 commands +FAE=n Data/Fax Auto Answer +FCLASS=n Service Class +FRH=n Receive data with HDLC framing +FRM=n Receive data +FRS=n Receive silence +FTH=n Transmit data with HDLC framing +FTM=n Transmit data +FTS=n Stop transmission and wait Fax Class 2 commands +FCLASS=n Services class. +FAA=n Adaptive answer. +FAXERR Fax error value. +FBOR Phase C data bit order. +FBUF? Buffer size (read only). +FCFR Indicate confirmation to receive. +FCLASS= Service class.
+FPHCTO Phase C time out. +FPOLL Indicates polling request. +FPTS: Page transfer status. +FPTS= Page transfer status. +FREV? Identify revision. +FSPT Enable polling. +FTSI: Report the transmit station ID.
Attention Switzerland User: If your Swisscom phone line does not have Taxsignal switched OFF, modem function may be impaired. The impairment may be resolved by a filter with the following specifications: Telekom PTT SCR-BE Taximpulssperrfilter-12kHz PTT Art. 444.112.7 Bakom 93.0291.Z.N Appendix C.
42 User Guide
Appendix D. Notices Lenovo may not offer the products, services, or features discussed in this document in all countries. Consult your local Lenovo representative for information on the products and services currently available in your area. Any reference to a Lenovo product, program, or service is not intended to state or imply that only that Lenovo product, program, or service may be used.
vary significantly. Some measurements may have been made on development-level systems and there is no guarantee that these measurements will be the same on generally available systems. Furthermore, some measurements may have been estimated through extrapolation. Actual results may vary. Users of this document should verify the applicable data for their specific environment. Television output notice The following notice applies to models that have the factory-installed television-output feature.
Index A I adapters connectors 14 installing 14 peripheral component interconnect (PCI) audio line in connector 9 audio line out connector 9 audio, subsystem 2 information resources xiii input/output (I/O) features 2 installing options adapters 14 DIMMs 13 external 6 memory 13 memory modules 13 security features 21 B battery location 12 boot-block recovery 32 K keyboard connector C cables, connecting 25 changing startup device sequence changing the battery 23 cleaning the mouse 33 CMOS, clearing 24 com
password (continued) lost or forgotten 24 setting, changing, deleting 28 user 28 passwords considerations 27 physical specifications 4 power Advanced Configuration and Power Interface (ACPI) support 3 R recovering from a POST/BIOS update failure 32 removing the cover 10 replacing battery 23 replacing the cover 25 S security cable lock 22 features 3, 21 integrated cable lock 23 padlock loop 23 selecting startup device 29 temporary startup device serial connector 9 Setup Utility 27 specifications physical 4
Part Number: 41D4435 Printed in USA (1P) P/N: 41D4435
