ThinkPad T410 and T410i Hardware Maintenance Manual
ThinkPad T410 and T410i Hardware Maintenance Manual
Note: Before using this information and the product it supports, be sure to read the general information under Appendix A “Notices” on page 191. Second Edition (October 2010) © Copyright Lenovo 2010. LENOVO products, data, computer software, and services have been developed exclusively at private expense and are sold to governmental entities as commercial items as defined by 48 C.F.R. 2.101 with limited and restricted rights to use, reproduction and disclosure.
Contents About this manual. . . . . . . . . . . . v Chapter 1. Safety information . . . . . 1 General safety . . . . . . . . . . . . . . . Electrical safety . . . . . . . . . . . . . . Safety inspection guide . . . . . . . . . . . Handling devices that are sensitive to electrostatic discharge. . . . . . . . . . . . . . . . . Grounding requirements . . . . . . . . . . . Safety notices (multilingual translations) . . . . . Laser compliance statement (multilingual translations) . . . . . . . . . . . . . . . .
1160 LCD unit . . . . . . . . . . . . . . . 1170 Fan assembly . . . . . . . . . . . . . 1180 CPU . . . . . . . . . . . . . . . . 1190 Base cover assembly, I/O sub card, and I/O sub card cable. . . . . . . . . . . . . . . 1200 Magnesium structure frame . . . . . . . 1210 System board, DC-in connector cable, and ExpressCard slot assembly. . . . . . . . . . 2010 LCD bezel assembly . . . . . . . . . . 2020 LED board . . . . . . . . . . . . . . 2030 Integrated camera . . . . . . . . . . .
About this manual This manual contains service and reference information for the following ThinkPad® products. ThinkPad T410 and T410i MT 2516, 2518, 2519, 2522, 2537, 2538, and 2539 Use this manual along with the advanced diagnostic tests to troubleshoot problems. Important: This manual is intended only for trained service technicians who are familiar with ThinkPad products. Use this manual along with the advanced diagnostic tests to troubleshoot problems effectively.
vi ThinkPad T410 and T410i Hardware Maintenance Manual
Chapter 1. Safety information This chapter presents following safety information that you need to be familiar with before you service a ThinkPad Notebook.
General safety Follow these rules to ensure general safety: • Observe good housekeeping in the area of the machines during and after maintenance. • When lifting any heavy object: 1. Make sure that you can stand safely without slipping. 2. Distribute the weight of the object equally between your feet. 3. Use a slow lifting force. Never move suddenly or twist when you attempt to lift. 4. Lift by standing or by pushing up with your leg muscles; this action removes the strain from the muscles in your back.
Electrical safety Observe the following rules when working on electrical equipment. Important: Use only approved tools and test equipment. Some hand tools have handles covered with a soft material that does not insulate you when working with live electrical currents. Many customers have, near their equipment, rubber floor mats that contain small conductive fibers to decrease electrostatic discharges. Do not use this type of mat to protect yourself from electrical shock.
– Use caution; do not become a victim yourself. – Switch off power. – Send another person to get medical aid.
Safety inspection guide The purpose of this inspection guide is to assist you in identifying potentially unsafe conditions. As each machine was designed and built, required safety items were installed to protect users and service technicians from injury. This guide addresses only those items. You should use good judgment to identify potential safety hazards due to attachment of non-ThinkPad features or options not covered by this inspection guide.
Handling devices that are sensitive to electrostatic discharge Any computer part containing transistors or integrated circuits (ICs) should be considered sensitive to electrostatic discharge (ESD.) ESD damage can occur when there is a difference in charge between objects. Protect against ESD damage by equalizing the charge so that the machine, the part, the work mat, and the person handling the part are all at the same charge. Notes: 1.
Safety notices (multilingual translations) The safety notices in this section are provided in the following languages: • English • Arabic • Brazilian Portuguese • French • German • Hebrew • Japanese • Korean • Spanish • Traditional Chinese Chapter 1.
DANGER Before the computer is powered on after FRU replacement, make sure all screws, springs, and other small parts are in place and are not left loose inside the computer. Verify this by shaking the computer and listening for rattling sounds. Metallic parts or metal flakes can cause electrical shorts. DANGER Some standby batteries contain a small amount of nickel and cadmium. Do not disassemble a standby battery, recharge it, throw it into fire or water, or short-circuit it.
DANGER To avoid shock, do not remove the plastic cover that protects the lower part of the inverter card. DANGER Though the main batteries have low voltage, a shorted or grounded battery can produce enough current to burn personnel or combustible materials. DANGER Unless hot swap is allowed for the FRU being replaced, do as follows before removing it: power off the computer, unplug all power cords from electrical outlets, remove the battery pack, and disconnect any interconnecting cables. Chapter 1.
10 ThinkPad T410 and T410i Hardware Maintenance Manual
Chapter 1.
PERIGO Antes de ligar o computador após a substituição da FRU, certifique-se de que todos os parafusos, molas e outras peças pequenas estejam no lugar e não estejam soltos dentro do computador. Verifique isso sacudindo o computador e procurando ouvir sons de peças soltas. Peças metálicas ou lascas de metal podem causar curto-circuito. PERIGO Algumas baterias reserva contêm uma pequena quantidade de níquel e cádmio.
PERIGO Para evitar choque elétrico, não remova a capa plástica que protege a parte inferior da placa inversora. PERIGO Embora as principais baterias possuam baixa voltagem, uma bateria em curto-circuito ou aterrada pode produzir corrente o bastante para queimar materiais de pessoal ou inflamáveis.
DANGER Avant de remettre l'ordinateur sous tension après remplacement d'une unité en clientèle, vérifiez que tous les ressorts, vis et autres pièces sont bien en place et bien fixées. Pour ce faire, secouez l'unité et assurez-vous qu'aucun bruit suspect ne se produit. Des pièces métalliques ou des copeaux de métal pourraient causer un court-circuit. DANGER Certaines batteries de secours contiennent du nickel et du cadmium. Ne les démontez pas, ne les rechargez pas, ne les exposez ni au feu ni à l'eau.
DANGER Afin d'éviter tout risque de choc électrique, ne retirez pas le cache en plastique protégeant la partie inférieure de la carte d'alimentation. DANGER Bien que le voltage des batteries principales soit peu élevé, le court-circuit ou la mise à la masse d'une batterie peut produire suffisamment de courant pour brûler des matériaux combustibles ou causer des brûlures corporelles graves.
VORSICHT Bevor nach einem FRU-Austausch der Computer wieder angeschlossen wird, muß sichergestellt werden, daß keine Schrauben, Federn oder andere Kleinteile fehlen oder im Gehäuse vergessen wurden. Der Computer muß geschüttelt und auf Klappergeräusche geprüft werden. Metallteile oder-splitter können Kurzschlüsse erzeugen. VORSICHT Die Bereitschaftsbatterie, die sich unter dem Diskettenlaufwerk befindet, kann geringe Mengen Nickel und Cadmium enthalten.
VORSICHT Die Leuchtstoffröhre im LCD-Bildschirm enthält Quecksilber. Bei der Entsorgung die örtlichen Bestimmungen für Sondermüll beachten. Der LCD-Bildschirm besteht aus Glas und kann zerbrechen, wenn er unsachgemäß behandelt wird oder der Computer auf den Boden fällt.
18 ThinkPad T410 and T410i Hardware Maintenance Manual
Chapter 1.
20 ThinkPad T410 and T410i Hardware Maintenance Manual
Chapter 1.
22 ThinkPad T410 and T410i Hardware Maintenance Manual
Chapter 1.
PELIGRO Antes de encender el sistema despues de sustituir una FRU, compruebe que todos los tornillos, muelles y demás piezas pequeñas se encuentran en su sitio y no se encuentran sueltas dentro del sistema. Compruébelo agitando el sistema y escuchando los posibles ruidos que provocarían. Las piezas metálicas pueden causar cortocircuitos eléctricos. PELIGRO Algunas baterías de reserva contienen una pequeña cantidad de níquel y cadmio.
PELIGRO Para evitar descargas, no quite la cubierta de plástico que rodea la parte baja de la tarjeta invertida. PELIGRO Aunque las baterías principales tienen un voltaje bajo, una batería cortocircuitada o con contacto a tierra puede producir la corriente suficiente como para quemar material combustible o provocar quemaduras en el personal.
26 ThinkPad T410 and T410i Hardware Maintenance Manual
Chapter 1.
Laser compliance statement (multilingual translations) The laser compliance statements in this section are provided in the following languages: • English • Arabic • Brazilian Portuguese • French • German • Hebrew • Japanese • Korean • Spanish • Traditional Chinese Some models of ThinkPad Notebook are equipped from the factory with an optical storage device such as a CD-ROM drive or a DVD-ROM drive. Such devices are also sold separately as options.
Chapter 1.
Alguns modelos de computador ThinkPad são equipados na fábrica com um dispositivo de armazenamento ótico, como uma unidade de CD-ROM ou de DVD-ROM. Tais dispositivos também são vendidos separadamente como opcionais. Se uma dessas unidades estiver instalada, ela é certificada nos Estados Unidos em conformidade com os requisitos do Department of Health and Human Services 21 Code of Federal Regulations (DHHS 21 CFR), Subcapítulo J, para produtos a laser da Classe 1.
Certains modèles d'ordinateur ThinkPad sont équipés d'origine d'une unité de stockage optique telle qu'une unité de CD-ROM ou de DVD-ROM. Ces unités sont également vendues séparément en tant qu'options. Si l'une de ces unités est installée, elle est certifiée conforme, aux Etats-Unis, aux normes indiquées dans le sous-chapitre J du DHHS 21 CFR relatif aux produits à laser de classe 1.
Einige ThinkPad-Modelle sind werkseitig mit einem CD-ROM- oder DVD-ROM-Laufwerk ausgestattet. CDund DVD-Laufwerke können auch gesondert als Zusatzeinrichtung erworben werden. Die Laufwerke erfüllen die Anforderungen gemäß IEC 60825-1 (International Electrotechnical Commission) und gemäß CENELEC EN 60825-1 für Laserprodukte der Klasse 1.
Chapter 1.
34 ThinkPad T410 and T410i Hardware Maintenance Manual
Chapter 1.
Algunos modelos de sistemas ThinkPad están equipados de fábrica con un dispositivo de almacenamiento óptico, como una unidad de CD-ROM o de DVD-ROM. Estas unidades también se venden por separado como opciones. Si está instalada alguna de dichas unidades, se certifica que en los Estados Unidos cumple los requisitos del Department of Health and Human Services 21 Code of Federal Regulations (DHHS 21 CFR) Subchapter J para productos láser de Clase 1.
Chapter 1.
38 ThinkPad T410 and T410i Hardware Maintenance Manual
Chapter 2.
Attention: The setup configuration on the computer you are servicing may have been customized. Running Automatic Configuration may alter the settings. Note the current configuration settings (using the View Configuration option); then, when service has been completed, verify that those settings remain in effect. Strategy for replacing a hard disk drive Always try to run a low-level format before replacing a hard disk drive. This will cause all customer data on the hard disk to be lost.
Strategy for replacing FRUs for CTO, CMV, and GAV Product definition Dynamic Configure To Order (CTO) This provides the ability for a customer to configure an IBM® or a Lenovo solution from an eSite, and have this configuration sent to fulfillment, where it is built and shipped directly to the customer. The machine label, Product Entitlement Warehouse (PEW), eSupport, and the HMM will load these products as the 4-digit MT and 3-digit model, where model = “CTO” (Example: 1829-CTO).
• Authorized IBM Business Partners can access Eclaim at the following Web site: https://wca.eclaim.com Using eSupport For Key Commodities (Examples - hard disk drive, system board, microprocessor, LCD, and memory) • eSupport can be used to view the list of key commodities built in a particular machine serial (this is the same record found in PEW). • eSupport can be accessed at the following Web site: http://www.lenovo.com/support • To view the key commodities, click on PARTS INFORMATION, then PARTS LOOKUP.
Chapter 3. General checkout This chapter presents following information: • “What to do first” on page 44 • “Checkout guide” on page 45 – “Diagnostics using PC-Doctor for DOS” on page 45 – “Lenovo ThinkVantage Toolbox (Lenovo System Toolbox)” on page 47 – “PC-Doctor for Rescue and Recovery” on page 48 – “FRU tests” on page 49 • “Power system checkout” on page 51 The descriptions in this chapter apply to any ThinkPad model that supports the PC-Doctor® for DOS diagnostics program.
What to do first When you do return a FRU, you must include the following information in the parts exchange form or parts return form that you attach to it: 1. Name and phone number of service technician 2. Date of service 3. Date on which the machine failed 4. Date of purchase 5. Failure symptoms, error codes appearing on the display, and beep symptoms 6. Procedure index and page number in which the failing FRU was detected 7. Failing FRU name and part number 8.
Checkout guide Use the following procedures as a guide in identifying and correcting problems with the ThinkPad Notebook. Note: The diagnostic tests are intended to test only ThinkPad products. The use of non-ThinkPad products, prototype cards, or modified options can lead to false indications of errors and invalid system responses. 1. Identify the failing symptoms in as much detail as possible. 2. Verify the symptoms.
6. Press cursor keys to select ATAPI CDx (x: 0, 1, ...) and then press Enter. 7. Follow the instructions on the screen. 8. The main panel of PC-Doctor appears. 9. Select Diagnostics with the arrow keys, and press Enter. Note: You can select an item not only with the arrow keys, but also with the TrackPoint® pointer. Instead of pressing Enter, click the left button. A pull-down menu appears. (Its exact form depends on the model.) Note: PC-Doctor menu does not mean the formal support device list.
Detecting system information with PC-Doctor PC-Doctor can detect the following system information: Hardware Info • • • • • • • • • • • System Configuration Memory Contents Physical Disk Drives Logical Disk Drives VGA Information IDE Drive Info PCI Information PNPISA Info SMBIOS Info VESA LCD Info Hardware Events Log • • • • • • • • • • • Run External Tests Surface Scan Hard Disk Benchmark System DOS Shell Tech Support Form Battery Rundown View Test Log Print Log Save Log Full Erase Hard Drive Quick Erase
Follow the instructions on the screen. Lenovo ThinkVantage Toolbox (Lenovo System Toolbox) also has problem determination aids that determine software and usage problems. For additional information about this program, see the Help for the program. PC-Doctor for Rescue and Recovery In some models of ThinkPad Notebook, the Rescue and Recovery® workspace enables you to run the PC-Doctor program to test the hardware features of the computer.
FRU tests The following table shows the test for each FRU. Table 1. FRU tests FRU System board Applicable test 1. Diagnostics ➙ CPU/Coprocessor 2. Diagnostics ➙ Systemboard 3. If the docking station or the port replicator is attached to the ThinkPad Notebook, detach it. 4. Place the computer on a horizontal surface, and run Diagnostics ➙ ThinkPad Devices ➙ HDD Active Protection Test. Note: Do not apply any physical shock to the computer while the test is running.
Table 1. FRU tests (continued) FRU Applicable test TrackPoint or pointing device If the TrackPoint does not work, check the configuration as specified in the BIOS Setup Utility. If the TrackPoint is disabled, select Automatic to enable it. After you use the TrackPoint, the pointer may drift on the screen for a short time. This drift can occur when a slight, steady pressure is applied to the TrackPoint pointer. This symptom is not a hardware problem.
Power system checkout To verify a symptom, do the following: 1. Turn off the computer. 2. Remove the battery pack. 3. Connect the ac adapter. 4. Check that power is supplied when you turn on the computer. 5. Turn off the computer. 6. Disconnect the ac adapter and install the charged battery pack. 7. Check that the battery pack supplies power when you turn on the computer.
Perform operational charging. If the battery status indicator or icon does not turn on, remove the battery pack and let it return to room temperature. Reinstall the battery pack. If the charge indicator or icon still does not turn on, replace the battery pack. If the charge indicator still does not turn on, replace the system board. Then reinstall the battery pack. If it is still not charged, go to the next section.
Red (+) Black (-) Wire Voltage (V dc) Red +2.5 to +3.2 Black Ground • If the voltage is correct, replace the system board. • If the voltage is not correct, replace the backup battery. • If the backup battery discharges quickly after replacement, replace the system board. Chapter 3.
54 ThinkPad T410 and T410i Hardware Maintenance Manual
Chapter 4. Related service information This chapter presents following information: • “Restoring the factory contents by using Recovery Disc Set” on page 55 • “Passwords” on page 56 • “Power management” on page 59 • “Symptom-to-FRU index” on page 61 Service Web site: When the latest maintenance diskette and the system program service diskette become available, they will be posted on http://www.lenovo.com/spm.
3. Press F10 to save the Setup Utility configuration changes. Follow the instructions on the screen to begin the recovery process. 4. Select your language and click Next. 5. Read the license. If you agree with the terms and conditions, select I accept these terms and conditions and then click Next. If you do not agree with the terms and conditions, follow the instructions on the screen. 6. Click Yes in the displayed window to begin the operating system recovery process. 7.
service technicians provide any services to reset either the user or the master HDP, or to recover data from the hard disk drive. The hard disk drive can be replaced for a scheduled fee. For how to remove the POP, see “How to remove the hard-disk password” on page 57. Supervisor password A supervisor password (SVP) protects the system information stored in the BIOS Setup Utility. The user must enter the SVP in order to get access to the BIOS Setup Utility and change the system configuration.
2. When the ThinkPad logo comes up, immediately press F1 to enter BIOS Setup Utility.For models supporting the Passphrase function, press F1 while HDP icon is appearing on the screen; then enter the master HDP. For the other models, enter the master HDP. Note: To check whether the ThinkPad Notebook you are servicing supports the Passphrase function, enter the BIOS Setup Utility and go to Security ➙ Password.
Power management To reduce power consumption, the computer has three power management modes: screen blank, sleep (standby in Windows XP), and hibernation. Screen blank mode If the time set on the “Turn off monitor” timer in the operating system expires, the LCD backlight turns off. To put the computer into screen blank mode, do as follows: 1. Press Fn+F3. A panel for selecting a power plan (in Windows XP, power scheme) appears. 2.
Hibernation mode In hibernation mode, the following occurs: • The system status, RAM, VRAM, and setup data are stored on the hard disk. • The system is powered off. Note: If the computer enters the hibernation mode while it is docked to the docking station, do not undock it before resuming normal operation. If you do undock it and then try to resume normal operation, you will get an error message, and you will have to restart the system.
Symptom-to-FRU index This section contains following information: • “Numeric error codes” on page 61 • “Error messages” on page 66 • “Beep symptoms” on page 67 • “No-beep symptoms” on page 67 • “LCD-related symptoms” on page 68 • “Intermittent problems” on page 69 • “Undetermined problems” on page 69 The symptom-to-FRU index in this section lists symptoms and errors and their possible causes. The most likely cause is listed first, in boldface type.
Table 2. Numeric error codes (continued) Symptom or error FRU or action, in sequence 0188 Invalid RFID Serialization Information Area. System board. 0189 Invalid RFID configuration information area—The EEPROM checksum is not correct. System board. 0190 Critical low-battery error 1. Charge the battery pack. 2. Battery pack. 0191 System Security—Invalid Remote Change requested. 1. Run BIOS Setup Utility, and then save current setting by pressing F10. 2. System board.
Table 2. Numeric error codes (continued) Symptom or error FRU or action, in sequence 021x Keyboard error. Run interactive tests of the keyboard and the auxiliary input device. 0220 Monitor type error—Monitor type does not match the one specified in CMOS. Load Setup Defaults in BIOS Setup Utility. 0230 Shadow RAM error—Shadow RAM fails at offset nnnn. System board. 0231 System RAM error—System RAM fails at offset nnnn. 1. DIMM. 2. System board.
Table 2. Numeric error codes (continued) Symptom or error FRU or action, in sequence 02F6 Software NMI failed 1. DIMM. 2. System board. 02F7 Fail-safe timer NMI failed 1. DIMM. 2. System board. 1801 Attached docking station is not supported Shut down the computer and remove it from the docking station. 1802 Unauthorized network card is plugged in—Turn off and remove the miniPCI network card. 1. Remove Mini PCI network card. 2. System board.
Table 2. Numeric error codes (continued) Symptom or error FRU or action, in sequence 2010 Warning: Your internal hard disk drive (HDD) may not function correctly on this system. Ensure that your HDD is supported on this system and that the latest HDD firmware is installed.
Error messages Table 3. Error messages Symptom or error FRU or action, in sequence Device address conflict. 1. Load “Setup Defaults” in the BIOS Setup Utility. 2. Backup battery. 3. System board. Allocation error for device. 1. Load “Setup Defaults” in the BIOS Setup Utility. 2. Backup battery. 3. System board. Failing bits: nnnn. 1. DIMM. 2. System board. Invalid system configuration data. 1. DIMM. 2. System board. I/O device IRQ conflict. 1. Load “Setup Defaults” in the BIOS Setup Utility. 2.
Beep symptoms Table 4. Beep symptoms Symptom or error FRU or action, in sequence One beep and a blank, unreadable, or flashing LCD. 1. 2. 3. 4. One long and two short beeps, and a blank or unreadable LCD. 1. System board. 2. LCD assembly. 3. DIMM. Two short beeps with error codes. Two short beeps and a blank screen. Two or more beeps, or a continuous beep. Operating system starts successfully. Three short beeps, pause, three more short beeps, and one short beep. Reseat the LCD connector.
LCD-related symptoms Important: The TFT LCD for the notebook computer contains many thin-film transistors (TFTs). The presence of a small number of dots that are missing, discolored, or always lighted is characteristic of TFT LCD technology, but excessive pixel problems can cause viewing concerns. If the LCD you are servicing has two or less visible defective pixels, it should not be considered faulty.
Intermittent problems Intermittent system hang problems can be due to a variety of causes that have nothing to do with a hardware defect, such as cosmic radiation, electrostatic discharge, or software errors. FRU replacement should be considered only when a problem recurs. When analyzing an intermittent problem, do the following: 1. Run the diagnostic test for the system board in loop mode at least 10 times. 2. If no error is detected, do not replace any FRUs. 3.
70 ThinkPad T410 and T410i Hardware Maintenance Manual
Chapter 5. Status indicators This chapter presents the system status indicators that show the status of the computer.
11 10 Table 7. Status indicators Indicator 1 Speaker mute Meaning Orange: The speaker is on mute. To set the speakers on mute or unmute, press the speaker mute button. 2 Microphone mute Orange: The microphone is on mute. None of the recording devices is available while the microphone mute is on by default. 3 Wireless LAN, Wireless WAN, or WiMAX status Green: The wireless LAN feature (the IEEE 802.11 b/g standard, 802.11 a/b/g, or 802.
Table 7. Status indicators (continued) Indicator 5 Device access Meaning Green: Data is being read from or written to the hard disk drive, the diskette drive, or the drive in the Serial Ultrabay Slim device. When this indicator is on, do not put the computer into sleep (standby) mode or turn off the computer. Note: Do not move the system while the green device access light is on. Sudden physical shock could cause drive errors. 6 Power on Green: The computer is on and ready to use.
Table 7. Status indicators (continued) Indicator 10 Battery status Meaning Green: The battery has more than 20% charge. Orange: The battery has between 5% and 20% charge. Fast blinking orange: The battery has less than 5% charge. Note: The battery may be charging. Slow blinking orange: The battery is being charged. When it reaches 20%, the blinking color changes to green. Slow blinking green: The battery has between 20% and 80% charge, and charging is continuing.
Chapter 6. Fn key combinations The following table shows the function of each combination of Fn with a function key. Table 8. Fn key combinations Key combination Description Fn+F1 Reserved. Fn+F2 Lock the computer. Fn+F3 Select a power plan (in Windows XP, power scheme) that has been created by Power Manager, or adjust the power level by using the slider control. When you press this combination, a panel for selecting a power plan (power scheme) appears.
Table 8. Fn key combinations (continued) Key combination Description Fn+F7 Apply a presentation scheme directly, with no need to start Presentation Director. To disable this function and use the Fn+F7 key combination for switching a display output location, start Presentation Director, and change the settings. Note: If the computer is an Windows 7 model, it does not support presentation schemes, however the Fn+F7 combination might still be used to switch display output location.
Table 8. Fn key combinations (continued) Key combination Description Fn+PgUp Turn the ThinkLight® on or off. Note: This function is supported only on the ThinkPad Notebooks that have the ThinkLight. The on or off status of the ThinkLight is shown on the screen for a few seconds when you press Fn+PgUp. Fn+Home The computer display becomes brighter. The purpose of this method is to change the brightness level temporarily.
78 ThinkPad T410 and T410i Hardware Maintenance Manual
Chapter 7. FRU replacement notices This chapter presents notices related to removing and replacing parts. Read this chapter carefully before replacing any FRU. Screw notices Loose screws can cause a reliability problem. In the ThinkPad Notebook, this problem is addressed with special nylon-coated screws that have the following characteristics: • • • • They maintain tight connections. They do not easily come loose, even with shock or vibration. They are harder to tighten. Each one should be used only once.
Retaining serial numbers This section includes the following descriptions: • • • “Restoring the serial number of the system unit” on page 80 “Retaining the UUID” on page 80 “Reading or writing the ECA information” on page 81 Restoring the serial number of the system unit When the computer was manufactured, the EEPROM on the system board was loaded with the serial numbers of the system and all major components. These numbers need to remain the same throughout the life of the computer.
designed to provide unique IDs until the year A.D. 3400. No two computers in the world have the same number. When you replace the system board, you must set the UUID on the new system board as follows: 1. Install the LENOVO ThinkPad Hardware Maintenance Diskette Version 1.76 or later, and restart the computer. 2. From the main menu, select 4. Assign UUID. A new UUID is created and written. If a valid UUID already exists, it is not overwritten.
82 ThinkPad T410 and T410i Hardware Maintenance Manual
Chapter 8. Removing and replacing a FRU This chapter presents directions and drawings for use in removing and replacing a FRU. Be sure to observe the following general rules: 1. Do not try to service any computer unless you have been trained and certified. An untrained person runs the risk of damaging parts. 2. Before replacing any FRU, review Chapter 7 “FRU replacement notices” on page 79. 3. Begin by removing any FRUs that have to be removed before the failing FRU.
Before servicing ThinkPad T410 and T410i Some models of the ThinkPad T410 and T410i you are servicing might have the SIM card that the customer has installed. If the computer you are servicing has the SIM card, remove it before you start the servicing. To remove the SIM card, you need to remove the battery pack first. (See “1010 Battery pack” on page 85.) After you finish the servicing, make sure that you insert the card back into the slot firmly.
1010 Battery pack Important notice for replacing a battery pack: ThinkVantage Toolbox (in Windows 7) and Lenovo System Toolbox (in Windows Vista and Windows XP) have an automatic battery diagnostic that determines if the battery pack is defective. A battery pack FRU should not be replaced unless this diagnostic shows that the battery is defective. The only exception to this is if the battery pack is physically damaged or a customer is reporting a possible safety issue.
1020 ExpressCard blank bezel Table 10. Removal steps of ExpressCard blank bezel When you press the ExpressCard blank bezel 1 , it pops out 2 . 1 2 When installing: Make sure that the bezel is correctly oriented as shown in this figure.
1030 Serial Ultrabay Slim device or travel bezel For access, remove this FRU: • “1010 Battery pack” on page 85 Table 11. Removal steps of Serial Ultrabay Slim device or travel bezel Holding the bay lock latch in the unlocked position 1 , slide the bay eject latch 2 , and then pull out the Ultrabay Slim Media Bay device or the travel bezel in the direction shown by arrow 3 . 1 2 3 4 Chapter 8.
1040 Hard disk drive (HDD) slot cover, HDD rubber rails and HDD or storage converter and solid state drive (SSD) For access, remove this FRU: • “1010 Battery pack” on page 85 Attention: • Do not drop the drive or apply any physical shock to it. The drive is sensitive to physical shock. Improper handling can cause damage and permanent loss of data. • Before removing the drive, have the user make a backup copy of all the information on it if possible.
Table 12. Removal steps of HDD slot cover, HDD rubber rails and HDD or storage converter and solid state drive (SSD) (continued) 3 For HDD and HDD rubber rails: 4 4 For SSD and storage converter: 4 5 When installing: Make sure that the SSD connector or HDD connector is attached firmly. Chapter 8.
1050 DIMM slot cover For access, remove this FRU: • “1010 Battery pack” on page 85 Table 13. Removal steps of DIMM slot cover Note: Loosen the screw 1 , but do not remove it.
1060 DIMM (in bottom slot) For access, remove these FRUs in order: • “1010 Battery pack” on page 85 • “1050 DIMM slot cover” on page 90 Note: This product has two DIMM slots: one under the keyboard and another on the underside of the computer. If you install a DIMM in only one of the two slots, install it in the slot located under the keyboard. Table 14. Removal steps of DIMM (in bottom slot) 1 2 1 When installing: Insert the notched end of the DIMM into the socket.
1070 PCI Express Mini Card for wireless WAN For access, remove these FRUs in order: • “1010 Battery pack” on page 85 • “1050 DIMM slot cover” on page 90 Table 15. Removal steps of PCI Express Mini Card for wireless WAN In step 3 , unplug the jacks by using the removal tool antenna RF connector (P/N: 08K7159) or pick the connectors with your fingers and gently unplug them in direction of the arrow. 1 1 2 2 92 Step Screw (quantity) Color Torque 2 M2 × 3 mm, wafer-head, nylon-coated (2) Black 0.
Table 15. Removal steps of PCI Express Mini Card for wireless WAN (continued) 3 Note: Plug the red cable into the jack labeled MAIN, and the blue cable into the jack labeled AUX on the card. If the computer you are servicing is a wireless WAN-ready model and does not have the wireless WAN card, route the antenna cables and secure them with a tape as shown in this figure. Chapter 8.
1080 Keyboard For access, remove these FRUs in order: • “1010 Battery pack” on page 85 • “1050 DIMM slot cover” on page 90 Table 16. Removal steps of keyboard 1 Step Screw (quantity) Color Torque 1 M2 × 10 mm, wafer-head, nylon-coated (1) Black 0.181 Nm (1.85 kgfcm) Push down the keyboard a little toward the arrow 2 to detach the front edge of the keyboard from the frame.
Table 16. Removal steps of keyboard (continued) 2 Lift the keyboard a little in the direction shown by arrow 3 , and then detach the connector 4 . 3 4 Chapter 8.
When installing the keyboard, do as follows: Table 17. Installation steps of keyboard 1. Attach the keyboard connector. 1 2. Attach the keyboard so that the keyboard edges a are under the frame as shown in this figure.
Table 17. Installation steps of keyboard (continued) a a 3. To make sure that the front edge of the keyboard is housed firmly, gently press the keys with your thumbs and try to slide the keyboard toward you. Chapter 8.
Table 17. Installation steps of keyboard (continued) 4. Make sure that front edge of the keyboard b is attached firmly. b b b 5. Secure the keyboard by tightening the screws from the bottom side of the computer.
1090 DIMM (in slot under keyboard) For access, remove these FRUs in order: • “1010 Battery pack” on page 85 • “1050 DIMM slot cover” on page 90 • “1080 Keyboard” on page 94 Note: This product has two DIMM slots: one under the keyboard and another on the underside of the computer. If you install a DIMM in only one of the two slots, install it in the slot located under the keyboard. Table 18. Removal steps of DIMM (in slot under keyboard) 1 Chapter 8.
Table 18. Removal steps of DIMM (in slot under keyboard) (continued) 2 3 2 When installing: Insert the notched end of the DIMM into the socket. Press the DIMM firmly, and pivot it until it snaps into the place. Make sure that it is firmly fixed in the slot and does not move easily.
1100 Backup battery For access, remove these FRUs in order: • “1010 Battery pack” on page 85 • “1050 DIMM slot cover” on page 90 • “1080 Keyboard” on page 94 Table 19. Removal steps of backup battery DANGER Use only the battery specified in the parts list for your computer. Any other battery could ignite or explode. 1 2 Chapter 8.
Table 19. Removal steps of backup battery (continued) Cable routing: Attach the backup battery and route the cable as shown in the figure below and make sure that the battery connector is attached firmly.
0 PCI Express Mini Card for wireless LAN For access, remove these FRUs in order: • “1010 Battery pack” on page 85 • “1050 DIMM slot cover” on page 90 • “1080 Keyboard” on page 94 Table 20. Removal steps of PCI Express Mini Card for wireless LAN In step 1 , unplug the jacks by using the removal tool antenna RF connector (P/N: 08K7159) or pick the connectors with your fingers and gently unplug them in direction of the arrow. Note: Some models might have only two antenna cables in step 1 .
Table 20. Removal steps of PCI Express Mini Card for wireless LAN (continued) 3 When installing: • In models with wireless LAN card that has two antenna connectors, plug the gray cable into the jack marked MAIN or M, and the black cable into the jack marked AUX or A on the card. If the computer you are servicing has three cables, put the white cable in the cable protection tube and secure it with a tape as shown in this figure.
1120 Keyboard bezel assembly, FPC cable, and Bluethooth daughter card (BDC-2.1) For access, remove these FRUs in order: • “1010 Battery pack” on page 85 • “1020 ExpressCard blank bezel” on page 86 • “1050 DIMM slot cover” on page 90 • “1080 Keyboard” on page 94 Note: FPC cable is attached on the underside of the keyboard bezel assembly. In some models, BDC is also attached on the underside of the keyboard bezel assembly. For the models do not have BDC, skip steps from 8 to 10 . Table 21.
Table 21. Removal steps of keyboard bezel assembly, FPC cable, and BDC-2.1 (continued) 3 3 3 3 Step Screw (quantity) Color Torque 3 M2 × 3 mm, wafer-head, nylon-coated (4) Black 0.181 Nm (1.
Table 21. Removal steps of keyboard bezel assembly, FPC cable, and BDC-2.1 (continued) 7 6 When installing: Make sure that the connector is attached firmly. 8 9 12 13 12 10 9 11 Chapter 8.
Table 21. Removal steps of keyboard bezel assembly, FPC cable, and BDC-2.1 (continued) When installing: Make sure that the connectors are attached firmly. 15 14 Step Screw (quantity) Color Torque 14 M2 × 3 mm, wafer-head, nylon-coated (1) Black 0.181 Nm (1.85 kgfcm) 16 When installing: Make sure that the connector is attached firmly.
1130 SmartCard or Contactless SmartCard For access, remove these FRUs in order: • “1010 Battery pack” on page 85 • “1050 DIMM slot cover” on page 90 • “1080 Keyboard” on page 94 • “1120 Keyboard bezel assembly, FPC cable, and Bluethooth daughter card (BDC-2.1)” on page 105 Table 22. Removal steps of SmartCard or Contactless SmartCard 1 1 1 1 Step Screw (quantity) Color Torque 1 M2 × 3 mm, wafer-head, nylon-coated (4) Black 0.181 Nm (1.85 kgfcm) Chapter 8.
Table 22. Removal steps of SmartCard or Contactless SmartCard (continued) 3 2 When installing: Make sure that the connector is attached firmly. Table 23. Removal steps of SmartCard dummy spacer Some models have SmartCard dummy spacer as a miscellaneous part. For those models, remove the spacer as follows: 1 1 1 1 2 Step Screw (quantity) Color Torque 1 M2 × 3 mm, wafer-head, nylon-coated (4) Black 0.181 Nm (1.
1140 Modem daughter card (MDC) For access, remove these FRUs in order: • “1010 Battery pack” on page 85 • “1050 DIMM slot cover” on page 90 • “1080 Keyboard” on page 94 • “1120 Keyboard bezel assembly, FPC cable, and Bluethooth daughter card (BDC-2.1)” on page 105 Table 24. Removal steps of modem daughter card (MDC) 1 1 2 Step Screw (quantity) Color Torque 1 M2 × 3 mm, wafer-head, nylon-coated (2) Black 0.181 Nm (1.85 kgfcm) When installing: Make sure that the connector is attached firmly.
1150 Speaker assembly For access, remove these FRUs in order: • “1010 Battery pack” on page 85 • “1050 DIMM slot cover” on page 90 • “1080 Keyboard” on page 94 • “1120 Keyboard bezel assembly, FPC cable, and Bluethooth daughter card (BDC-2.1)” on page 105 Table 25. Removal steps of speaker assembly 1 1 1 1 Step Screw (quantity) Color Torque 1 M2 × 3 mm, wafer-head, nylon-coated (4) Black 0.181 Nm (1.
Table 25. Removal steps of speaker assembly (continued) 3 2 3 When installing: Attach the speaker assembly and route the cable as shown in this figure, and make sure that the speaker connector is attached firmly. Chapter 8.
1160 LCD unit For access, remove these FRUs in order: • “1010 Battery pack” on page 85 • “1020 ExpressCard blank bezel” on page 86 • “1050 DIMM slot cover” on page 90 • “1070 PCI Express Mini Card for wireless WAN” on page 92 • “1080 Keyboard” on page 94 • “1110 PCI Express Mini Card for wireless LAN” on page 103 • “1120 Keyboard bezel assembly, FPC cable, and Bluethooth daughter card (BDC-2.1)” on page 105 Table 26. Removal steps of LCD unit 1 1 Step Screw (quantity) Color Torque 1 M2.
Table 26. Removal steps of LCD unit (continued) 2 3 4 5 Step Screw (quantity) Color Torque 2 M2 × 3 mm, wafer-head, nylon-coated (1) Black 0.181 Nm (1.85 kgfcm) 4 M2 × 3 mm, wafer-head, nylon-coated (1) Black 0.181 Nm (1.85 kgfcm) Chapter 8.
Table 26. Removal steps of LCD unit (continued) 8 8 6 7 Step Screw (quantity) Color Torque 8 M2.5 × 6 mm, wafer-head, nylon-coated (2) Black 0.392 Nm (4.
Table 26. Removal steps of LCD unit (continued) When installing: • Make sure that you attach the connectors and route the cables firmly, and tape up in the proper positions as shown in this figure. • When you route the cables, make sure that they are not subjected to any tension. Tension could cause the cables to be damaged by the cable guides, or a wire to be broken. 11 Chapter 8.
Table 26.
1170 Fan assembly For access, remove these FRUs in order: • “1010 Battery pack” on page 85 • “1020 ExpressCard blank bezel” on page 86 • “1050 DIMM slot cover” on page 90 • “1070 PCI Express Mini Card for wireless WAN” on page 92 • “1080 Keyboard” on page 94 • “1110 PCI Express Mini Card for wireless LAN” on page 103 • “1120 Keyboard bezel assembly, FPC cable, and Bluethooth daughter card (BDC-2.1)” on page 105 • “1150 Speaker assembly” on page 112 • “1160 LCD unit” on page 114 Table 27.
Table 27. Removal steps of fan assembly (continued) 5 4 When installing: • Before you attach the fan assembly to the computer, apply thermal grease, at an amount of 0.2 grams, on the parts marked a as in the following figures. Either too much or too less application of grease can cause a thermal problem due to imperfect contact with a component. For the fan in the integrated graphics models, you need to peel the thin film off from the thermal rubber marked b .
Table 27. Removal steps of fan assembly (continued) For Integrated graphics models: a • When attaching the fan assembly to the frame, take care not to damage the heat sink ( a ) of the fan assembly. a a • Make sure that the fan connector is attached firmly. Chapter 8.
1180 CPU For access, remove these FRUs in order: • “1010 Battery pack” on page 85 • “1020 ExpressCard blank bezel” on page 86 • “1050 DIMM slot cover” on page 90 • “1070 PCI Express Mini Card for wireless WAN” on page 92 • “1080 Keyboard” on page 94 • “1110 PCI Express Mini Card for wireless LAN” on page 103 • “1120 Keyboard bezel assembly, FPC cable, and Bluethooth daughter card (BDC-2.
1190 Base cover assembly, I/O sub card, and I/O sub card cable For access, remove these FRUs in order: • “1010 Battery pack” on page 85 • “1020 ExpressCard blank bezel” on page 86 • “1030 Serial Ultrabay Slim device or travel bezel” on page 87 • “1040 Hard disk drive (HDD) slot cover, HDD rubber rails and HDD or storage converter and solid state drive (SSD)” on page 88 • “1050 DIMM slot cover” on page 90 • “1070 PCI Express Mini Card for wireless WAN” on page 92 • “1080 Keyboard” on page 94 • “1110 PCI Expr
Table 29. Removal steps of base cover assembly, I/O sub card, and I/O sub card cable (continued) 4 3 3 3 5 5 Step Screw (quantity) Color Torque 3 M2 × 3 mm, wafer-head, nylon-coated (3) Black 0.181 Nm (1.85 kgfcm) When installing: Make sure that the connector is attached firmly.
Table 29. Removal steps of base cover assembly, I/O sub card, and I/O sub card cable (continued) 6 6 7 8 a When installing: Make sure that wireless switch is adjusted as shown in figure a . 9 Chapter 8.
Table 29. Removal steps of base cover assembly, I/O sub card, and I/O sub card cable (continued) 11 11 10 12 Step Screw (quantity) Color Torque 11 M2 × 3.5 mm, flat-head, nylon-coated (2) Silver 0.181 Nm (1.85 kgfcm) 13 When installing: Make sure that connectors are firmly attached and route the cables as shown in this figure.
Table 29. Removal steps of base cover assembly, I/O sub card, and I/O sub card cable (continued) Chapter 8.
Table 29. Removal steps of base cover assembly, I/O sub card, and I/O sub card cable (continued) Note: Applying labels to the base cover The new base cover FRU is shipped with a kit containing labels of several kinds. When you replace the base cover, you need to apply the following labels: 18 Homologation label Following labels need to be peeled off from the old base cover, and need to be put on the new base cover.
For the location of each label, refer the following figure: 1 2 3 4 5 20 6 7 19 8 9 10 18 11 12 17 16 15 14 13 Chapter 8.
1200 Magnesium structure frame For access, remove these FRUs in order: • “1010 Battery pack” on page 85 • “1020 ExpressCard blank bezel” on page 86 • “1030 Serial Ultrabay Slim device or travel bezel” on page 87 • “1040 Hard disk drive (HDD) slot cover, HDD rubber rails and HDD or storage converter and solid state drive (SSD)” on page 88 • “1050 DIMM slot cover” on page 90 • “1070 PCI Express Mini Card for wireless WAN” on page 92 • “1080 Keyboard” on page 94 • “1110 PCI Express Mini Card for wireless LAN”
Table 30. Removal steps of magnesium structure frame (continued) 8 7 Chapter 8.
1210 System board, DC-in connector cable, and ExpressCard slot assembly For access, remove these FRUs, in order: • “1010 Battery pack” on page 85 • “1020 ExpressCard blank bezel” on page 86 • “1030 Serial Ultrabay Slim device or travel bezel” on page 87 • “1040 Hard disk drive (HDD) slot cover, HDD rubber rails and HDD or storage converter and solid state drive (SSD)” on page 88 • “1050 DIMM slot cover” on page 90 • “1070 PCI Express Mini Card for wireless WAN” on page 92 • “1080 Keyboard” on page 94 • “111
Table 31. Removal steps of system board, DC-in connector cable, and ExpressCard slot assembly Following components soldered on the top side of the system board are extremely sensitive. When you service the system board, avoid any kind of rough handling. a CPU b Accelerometer chip for the HDD Active Protection System™ c PCH (Platform Controller Hub) d GPU (Graphic Processing Unit): Discrete graphics chip Note: GPU ( d ) is only for the Switchable Graphics models.
Table 31. Removal steps of system board, DC-in connector cable, and ExpressCard slot assembly (continued) 2 1 1 Step Screw (quantity) Color Torque 1 M2 × 10 mm, wafer-head, nylon-coated (2) Black 0.181 Nm (1.85 kgfcm) 2 M2 × 5 mm, wafer-head, nylon-coated (1) Black 0.181 Nm (1.85 kgfcm) 3 4 When installing: Make sure that the connector is attached firmly.
2010 LCD bezel assembly For access, remove the following FRU: • “1010 Battery pack” on page 85 Table 32. Removal steps of LCD bezel assembly 1 1 Step 1 Screw cap Screw (quantity) Color Torque M2.5 × 6 mm, wafer-head, nylon-coated (4) Black 0.392 Nm (4.0 kgfcm) Chapter 8.
Table 32.
2020 LED board For access, remove these FRUs in order: • “1010 Battery pack” on page 85 • “2010 LCD bezel assembly” on page 135 Table 33. Removal steps of LED board 1 2 1 3 Step Screw (quantity) Color Torque 1 M2 × 3.5 mm, flat-head, nylon-coated (2) Silver 0.181 Nm (1.85 kgfcm) When installing: Make sure that the connector is attached firmly. Chapter 8.
2030 Integrated camera For access, remove these FRUs, in order: • “1010 Battery pack” on page 85 • “2010 LCD bezel assembly” on page 135 Table 34. Removal steps of integrated camera 1 3 2 Step Screw (quantity) Color Torque 1 M2 × 3.5 mm, flat-head, nylon-coated (1) Silver 0.181 Nm (1.85 kgfcm) When installing: Make sure that the connector is attached firmly.
2040 LCD panel and LCD cable For access, remove these FRUs in order: • “1010 Battery pack” on page 85 • “1020 ExpressCard blank bezel” on page 86 • “1050 DIMM slot cover” on page 90 • “1070 PCI Express Mini Card for wireless WAN” on page 92 • “1080 Keyboard” on page 94 • “1110 PCI Express Mini Card for wireless LAN” on page 103 • “1120 Keyboard bezel assembly, FPC cable, and Bluethooth daughter card (BDC-2.
Table 35. Removal steps of LCD panel and LCD cable (continued) 6 7 6 6 7 6 Step Screw (quantity) Color Torque 6 M2 × 3 mm, wafer-head, nylon-coated (4) Black 0.181 Nm (1.85 kgfcm) When installing: When attaching the LCD panel to the cover, press the left and right edges covered with metal gently with your fingers. DO NOT press the surface of the panel or apply any excessive force to the panel. 9 8 When installing: Make sure that the connector is attached firmly.
2050 Camera cable For access, remove these FRUs in order: • “1010 Battery pack” on page 85 • “1020 ExpressCard blank bezel” on page 86 • “1050 DIMM slot cover” on page 90 • “1070 PCI Express Mini Card for wireless WAN” on page 92 • “1080 Keyboard” on page 94 • “1110 PCI Express Mini Card for wireless LAN” on page 103 • “1120 Keyboard bezel assembly, FPC cable, and Bluethooth daughter card (BDC-2.
Table 36. Removal steps of camera cable (continued) Cable routing: When you install the cable, route the cable as shown in the figure below.
2060 Wireless LAN antenna assembly or wireless LAN/WAN antenna assembly For access, remove these FRUs in order: • “1010 Battery pack” on page 85 • “1020 ExpressCard blank bezel” on page 86 • “1050 DIMM slot cover” on page 90 • “1070 PCI Express Mini Card for wireless WAN” on page 92 • “1080 Keyboard” on page 94 • “1110 PCI Express Mini Card for wireless LAN” on page 103 • “1120 Keyboard bezel assembly, FPC cable, and Bluethooth daughter card (BDC-2.
Table 37. Removal steps of wireless LAN antenna assembly or wireless LAN/WAN antenna assembly (continued) 3 4 3 4 4 4 4 Step Screw (quantity) Color Torque 3 M2 × 3.5 mm, flat-head, nylon-coated (2) Silver 0.181 Nm (1.
2070 Hinges and LCD rear cover assembly For access, remove these FRUs in order: • “1010 Battery pack” on page 85 • “1020 ExpressCard blank bezel” on page 86 • “1050 DIMM slot cover” on page 90 • “1070 PCI Express Mini Card for wireless WAN” on page 92 • “1080 Keyboard” on page 94 • “1110 PCI Express Mini Card for wireless LAN” on page 103 • “1120 Keyboard bezel assembly, FPC cable, and Bluethooth daughter card (BDC-2.
146 ThinkPad T410 and T410i Hardware Maintenance Manual
Chapter 9. Locations This chapter presents the location of ThinkPad T410 and T410i features and hardware.
1 21 2 3 20 19 5 4 17 5 16 15 6 7 18 14 8 9 13 10 11 12 148 ThinkPad T410 and T410i Hardware Maintenance Manual
Rear view 1 Status indicators Note: For the description of each indicator, see Chapter 5 “Status indicators” on page 71. 2 DisplayPort 3 HDD or SSD 4 Universal serial bus (USB) connectors 5 RJ-45 (Ethernet) connector 6 External monitor connector 7 AC power connector 8 RJ-11 (modem) connector 1 2 8 3 4 7 5 6 Chapter 9.
Bottom view 1 Battery pack 2 Battery pack latch 3 DIMM slot 4 Docking connector 5 LCD cover latch 6 Media Card Reader slot 7 Serial Ultrabay Slim lock latch 8 Serial Ultrabay Slim eject latch 8 7 1 2 3 4 6 5 150 ThinkPad T410 and T410i Hardware Maintenance Manual
Chapter 10. Parts list This chapter contains following lists of the service parts. • “Overall” on page 152 • “LCD FRUs” on page 168 • “Keyboard” on page 176 • “Miscellaneous parts” on page 177 • “AC adapters” on page 179 • “Power cords” on page 180 • “Recovery discs” on page 181 • “Common service tools” on page 189 Notes: • Each FRU is available for all types or models, unless specific types or models are specified.
Overall 152 ThinkPad T410 and T410i Hardware Maintenance Manual
Table 39. Parts list—Overall No. FRU (Overall) FRU no. CRU ID af See “Miscellaneous parts” on page 177. 1 LCD unit (see “LCD FRUs” on page 168.
Table 39. Parts list—Overall (continued) No. FRU (Overall) FRU no.
Table 39. Parts list—Overall (continued) No. FRU (Overall) FRU no.
Table 39. Parts list—Overall (continued) No. FRU (Overall) FRU no.
Table 39. Parts list—Overall (continued) No. FRU (Overall) FRU no.
Table 39. Parts list—Overall (continued) No. FRU (Overall) FRU no.
Table 39. Parts list—Overall (continued) No. FRU (Overall) FRU no.
Table 39. Parts list—Overall (continued) No. FRU (Overall) FRU no. — 1.8" - 2.
Table 39. Parts list—Overall (continued) No. FRU (Overall) FRU no.
Table 39. Parts list—Overall (continued) No. FRU (Overall) FRU no. CRU ID 18 System board assembly, discrete graphics 256 MB, iAMT, non-TPM • 2516-CTO, A5x • 2518-CTO, C9x, EPx, EQx, ERx, ESx, GSx • 2519-CTO, 85x • 2522-CTO, 2Fx • 2537-CTO • 2538-CTO • 2539-CTO 60Y5718 N 19 CPU assembly, Intel® CoreTM i5-520M Processor (2.
Table 39. Parts list—Overall (continued) No. FRU (Overall) FRU no. CRU ID 19 CPU assembly, Intel Core i3-350M Processor (2.26 GHz) • 2516-CTO • 2518-CTO • 2519-CTO • 2522-CTO • 2537-CTO • 2538-CTO • 2539-CTO 63Y2175 N 19 CPU assembly, Intel Core i5-430M Processor (2.
Table 39. Parts list—Overall (continued) No. FRU (Overall) FRU no.
Table 39. Parts list—Overall (continued) No. FRU (Overall) FRU no.
Table 39. Parts list—Overall (continued) No. FRU (Overall) FRU no.
Table 39. Parts list—Overall (continued) No. FRU (Overall) FRU no. CRU ID 27 Bluetooth daughter card (BDC-2.
LCD FRUs In ThinkPad T410 and T410i, there are following types of LCDs. • 14.1-inch WXGA LED-backlight LCD (Table 40 “Parts list—14.1-inch WXGA LED-backlight LCD” on page 169) • 14.1-inch WXGA+ LED-backlight LCD (Table 41 “Parts list—14.
Table 40. Parts list—14.1-inch WXGA LED-backlight LCD No. FRU (14.1-inch WXGA LED-backlight LCD) FRU no. CRU ID a, b See “Miscellaneous parts” on page 177.
Table 40. Parts list—14.1-inch WXGA LED-backlight LCD (continued) No. FRU (14.1-inch WXGA LED-backlight LCD) FRU no. CRU ID 2 LCD module, 14.
Table 40. Parts list—14.1-inch WXGA LED-backlight LCD (continued) No. FRU (14.1-inch WXGA LED-backlight LCD) FRU no.
Table 40. Parts list—14.1-inch WXGA LED-backlight LCD (continued) No. FRU (14.1-inch WXGA LED-backlight LCD) FRU no.
Table 41. Parts list—14.1-inch WXGA+ LED-backlight LCD (continued) No. FRU (14.1-inch WXGA+ LED-backlight LCD) FRU no. CRU ID 3 LCD module, 14.
Table 41. Parts list—14.1-inch WXGA+ LED-backlight LCD (continued) No. FRU (14.1-inch WXGA+ LED-backlight LCD) FRU no.
Table 41. Parts list—14.1-inch WXGA+ LED-backlight LCD (continued) No. FRU (14.1-inch WXGA+ LED-backlight LCD) FRU no.
Keyboard Table 42. Parts list—Keyboard Language FRU no.
Miscellaneous parts Table 43. Parts list—Miscellaneous parts FRU FRU no. CRU ID Screw kit: • M2 × 3 mm (silver), small head (50) • M2 × 3.5 mm (black), wafer head (15) • M2 × 5 mm (black), wafer head (15) • M2 × 10 mm (black), wafer head (15) • M2 × 14 mm (black), wafer head (10) • M2.5 × 6 mm (black), flat head (20) • M3 × 2.
Table 43. Parts list—Miscellaneous parts (continued) FRU FRU no. CRU ID System miscellaneous parts: • (a) Express dummy card • (b) EMI bracket • (c) RJ-11 cable assembly, integrated • (c) RJ-11 cable assembly, discrete • (d) SmartCard spacer • (e) Bracket, fan for video • (f) LCD connector bracket • Insulation sheet for CPU • Bracket assembly, CPU support • Dummy cover, eSATA • Dummy cover, RJ-11 Note: Italicized letters in parentheses are references to the exploded view in “Overall” on page 152.
AC adapters Table 44. Parts list—2-pin AC adapters FRU FRU no.
Power cords A ThinkPad power cord for a specific country or region is usually available only in that country or region: Table 47. Parts list—2-pin power cords Country or region FRU no. Argentina • models -CTO, xxY 42T5020 42T5105 Brazil • models -CTO, xxP 42T5180 42T5183 Canada, U.S. • models -CTO, xxF, xxL, xxS, xxU 42T5008 42T5093 Japan • models -CTO, xxE, xxJ 42T5014 42T5099 CRU ID * Table 48. Parts list—3-pin power cords Country or region FRU no.
Recovery discs Windows XP Professional (32 bit) DVDs Windows XP Professional (32 bit) is preinstalled as the operating system in the following models: • 2516-CTO • 2518-CTO, C3x, C5x, CAx, CCx, CEx, CRx, CSx, CWx, CXx, D2x, D3x, D6x, D7x, DAx, DBx, DEx, DFx, DJx, DKx, DNx, DPx, DSx, DTx, F4x • 2519-CTO • 2522-CTO, 36x, 38x, 62x, 63x • 2537-CTO, 9Ax, 9Bx, 9Cx • 2538-CTO • 2539-CTO Table 49.
Windows Vista Business (32 bit) DVDs Windows Vista Business (32 bit) is preinstalled as the operating system in the following models: • 2516-CTO • 2518-CTO • 2519-CTO • 2522-CTO • 2537-CTO • 2538-CTO • 2539-CTO Table 50.
Windows 7 Home Basic (32 bit) DVDs Windows 7 Home Basic (32 bit) is preinstalled as the operating system in the following models: • 2516-CTO, A2x, A3x, A4x, A5x, A7x, A9x, ACx, AFx, AHx, AJx, AKx, ALx, AMx • 2518-CTO, DUx, FYx, G3x • 2519-CTO, 87x • 2522-CTO • 2537-CTO • 2538-CTO • 2539-CTO Table 51.
Windows 7 Home Premium (32 bit) DVDs Windows 7 Home Premium (32 bit) is preinstalled as the operating system in the following models: • 2516-CTO • 2518-CTO, E9x, EDx, FSx, FUx, FWx, GLx • 2519-CTO, 82x, 83x, 84x, 85x, 89x • 2522-CTO • 2537-CTO • 2538-CTO • 2539-CTO Table 52.
Windows 7 Home Premium (64 bit) DVDs Windows 7 Home Premium (64 bit) is preinstalled as the operating system in the following models: • 2516-CTO • 2518-CTO • 2519-CTO • 2522-CTO • 2537-CTO • 2538-CTO • 2539-CTO Table 53.
Windows 7 Professional (32 bit) DVDs Windows 7 Professional (32 bit) is preinstalled as the operating system in the following models: • 2516-CTO, A6x, A8x, AAx, ADx, AEx, AGx, ANx • 2518-CTO, C2x, C4x, C6x, C7x, C8x, C9x, CBx, CDx, CFx, CGx, CHx, CJx, CKx, CLx, CMx, CNx, CPx, CQx, CUx, CVx, CYx, CZx, D4x, D5x, D8x, D9x, DCx, DDx, DGx, DHx, DLx, DMx, DQx, DRx, DVx, DWx, DXx, DYx, DZx, E4x, E7x, ELx, EMx, ENx, EPx, EQx, ERx, ESx, EXx, EYx, EZx, F2x, F3x, F5x, F6x, FHx, FJx, FKx, FLx, FMx, FNx, FZx, G2x, G4x,
Table 54. Parts list—Windows 7 Professional (32 bit) recovery DVDs (continued) Language P/N Simplified Chinese 58Y4305 Slovak 58Y4324 Slovenian 58Y4325 Spanish 58Y4326 Traditional Chinese 58Y4306 Traditional Chinese (Hong Kong S.A.R.) 58Y4313 Turkish 58Y4328 Chapter 10.
Windows 7 Professional (64 bit) DVDs Windows 7 Professional (64 bit) is preinstalled as the operating system in the following models: • 2516-CTO, ABx • 2518-CTO, E8x, EAx, EBx, ECx, EEx, EFx, EGx, ETx, EUx, EVx, EWx, FDx, FEx, FFx, FGx, FQx, FTx, FVx, FXx, G7x, G8x, G9x, GEx, GFx, GGx • 2519-CTO • 2522-CTO, 3Fx, 3Gx, 3Tx, 3Ux, 3Yx, 3Zx, 42x, 43x • 2537-CTO • 2538-CTO • 2539-CTO Table 55.
Common service tools Table 56. Parts list—Common service tools Tool P/N Screwdriver kit 95F3598 1/4" drive spinner handle 1650840 1/4" Sq. to 1/4" hex torx adapter 93F2838 TR7-TR-10 tamper resistant torx bits 00P6967 Removal tool antenna RF connector 08K7159 USB 2.
190 ThinkPad T410 and T410i Hardware Maintenance Manual
Appendix A. Notices Lenovo may not offer the products, services, or features discussed in this document in all countries. Consult your local Lenovo representative for information on the products and services currently available in your area. Any reference to a Lenovo product, program, or service is not intended to state or imply that only that Lenovo product, program, or service may be used.
Trademarks The following terms are trademarks of Lenovo in the United States, other countries or both: Active Protection System Lenovo Rescue and Recovery ThinkLight ThinkPad ThinkVantage TrackPoint Ultrabay UltraNav IBM® (used under license) is trademark of the International Business Machines Corporation in the United States, other countries, or both: The following terms are trademarks of Microsoft Corporation in the United States, other countries, or both: Windows Windows Vista The following terms are tra
Part Number: 63Y0535_01 Printed in (1P) P/N: 63Y0535_01
*63Y0535_01*
