ThinkPad R500 Hardware Maintenance Manual
ThinkPad R500 Hardware Maintenance Manual
Note Before using this information and the product it supports, be sure to read the general information under “Notices” on page 215. Fourth Edition (July 2013) © Copyright Lenovo 2008, 2013. LENOVO products, data, computer software, and services have been developed exclusively at private expense and are sold to governmental entities as commercial items as defined by 48 C.F.R. 2.101 with limited and restricted rights to use, reproduction and disclosure.
Contents About this manual . . . . . . . . . . v Safety information . . . . . . . . . . 1 General safety . . . . . . . . . . . . . . 2 Electrical safety . . . . . . . . . . . . . 3 Safety inspection guide . . . . . . . . . . . 5 Handling devices that are sensitive to electrostatic discharge . . . . . . . . . . . . . . . 6 Grounding requirements . . . . . . . . . . 6 Safety notices (multilingual translations) . . . . . 7 Laser compliance statement (multilingual translations) . . . . . . . . . . . . . .
Parts list . . . . . . . . . . . . . 141 Overall . . . . . . . . . . . . . . . LCD FRUs . . . . . . . . . . . . . . Keyboard. . . . . . . . . . . . . . . Miscellaneous parts . . . . . . . . . . . AC adapters. . . . . . . . . . . . . . Power cords . . . . . . . . . . . . . . Recovery discs . . . . . . . . . . . . . Windows XP Professional (32 bit) DVDs . . . Windows Vista Starter Edition (32 bit) recovery DVDs . . . . . . . . . . . . . . . Windows Vista Home Basic (32 bit) recovery DVDs . . . . . . . . . . .
About this manual This manual contains service and reference information for the following ThinkPad® products. ThinkPad R500 MT 2713, 2714, 2716, 2717, 2718, 2719, 2720, 2731, 2732, 2733, 2734, 2735, 2736, and 2737 Use this manual along with the advanced diagnostic tests to troubleshoot problems. Important: This manual is intended only for trained service technicians who are familiar with ThinkPad products. Use this manual along with the advanced diagnostic tests to troubleshoot problems effectively.
vi ThinkPad R500 Hardware Maintenance Manual
Safety information This chapter presents following safety information that you need to be familiar with before you service a ThinkPad Notebook.
General safety Follow these rules to ensure general safety: v Observe good housekeeping in the area of the machines during and after maintenance. v When lifting any heavy object: 1. Make sure that you can stand safely without slipping. 2. Distribute the weight of the object equally between your feet. 3. Use a slow lifting force. Never move suddenly or twist when you attempt to lift. 4. Lift by standing or by pushing up with your leg muscles; this action removes the strain from the muscles in your back.
Electrical safety Observe the following rules when working on electrical equipment. Important: Use only approved tools and test equipment. Some hand tools have handles covered with a soft material that does not insulate you when working with live electrical currents. Many customers have, near their equipment, rubber floor mats that contain small conductive fibers to decrease electrostatic discharges. Do not use this type of mat to protect yourself from electrical shock.
v Do not touch live electrical circuits with the reflective surface of a plastic dental mirror. The surface is conductive; such touching can cause personal injury and machine damage. v Do not service the following parts with the power on when they are removed from their normal operating places in a machine: – Power supply units – Pumps – Blowers and fans – Motor generators – Similar units to listed above This practice ensures correct grounding of the units.
Safety inspection guide The purpose of this inspection guide is to assist you in identifying potentially unsafe conditions. As each machine was designed and built, required safety items were installed to protect users and service technicians from injury. This guide addresses only those items. You should use good judgment to identify potential safety hazards due to attachment of non-ThinkPad features or options not covered by this inspection guide.
Handling devices that are sensitive to electrostatic discharge Any computer part containing transistors or integrated circuits (ICs) should be considered sensitive to electrostatic discharge (ESD.) ESD damage can occur when there is a difference in charge between objects. Protect against ESD damage by equalizing the charge so that the machine, the part, the work mat, and the person handling the part are all at the same charge. Notes: 1.
Safety notices (multilingual translations) The safety notices in this section are provided in the following languages: v English v Arabic v Brazilian Portuguese v French v German v Hebrew v Japanese v Korean v Spanish v Traditional Chinese Safety information 7
DANGER Before the computer is powered on after FRU replacement, make sure all screws, springs, and other small parts are in place and are not left loose inside the computer. Verify this by shaking the computer and listening for rattling sounds. Metallic parts or metal flakes can cause electrical shorts. DANGER Some standby batteries contain a small amount of nickel and cadmium. Do not disassemble a standby battery, recharge it, throw it into fire or water, or short-circuit it.
DANGER To avoid shock, do not remove the plastic cover that protects the lower part of the inverter card. DANGER Though the main batteries have low voltage, a shorted or grounded battery can produce enough current to burn personnel or combustible materials. DANGER Unless hot swap is allowed for the FRU being replaced, do as follows before removing it: power off the computer, unplug all power cords from electrical outlets, remove the battery pack, and disconnect any interconnecting cables.
10 ThinkPad R500 Hardware Maintenance Manual
Safety information 11
PERIGO Antes de ligar o computador após a substituição da FRU, certifique-se de que todos os parafusos, molas e outras peças pequenas estejam no lugar e não estejam soltos dentro do computador. Verifique isso sacudindo o computador e procurando ouvir sons de peças soltas. Peças metálicas ou lascas de metal podem causar curto-circuito. PERIGO Algumas baterias reserva contêm uma pequena quantidade de níquel e cádmio.
PERIGO Para evitar choque elétrico, não remova a capa plástica que protege a parte inferior da placa inversora. PERIGO Embora as principais baterias possuam baixa voltagem, uma bateria em curto-circuito ou aterrada pode produzir corrente o bastante para queimar materiais de pessoal ou inflamáveis.
DANGER Avant de remettre l’ordinateur sous tension après remplacement d’une unité en clientèle, vérifiez que tous les ressorts, vis et autres pièces sont bien en place et bien fixées. Pour ce faire, secouez l’unité et assurez-vous qu’aucun bruit suspect ne se produit. Des pièces métalliques ou des copeaux de métal pourraient causer un court-circuit. DANGER Certaines batteries de secours contiennent du nickel et du cadmium. Ne les démontez pas, ne les rechargez pas, ne les exposez ni au feu ni à l’eau.
DANGER Afin d’éviter tout risque de choc électrique, ne retirez pas le cache en plastique protégeant la partie inférieure de la carte d’alimentation. DANGER Bien que le voltage des batteries principales soit peu élevé, le court-circuit ou la mise à la masse d’une batterie peut produire suffisamment de courant pour brûler des matériaux combustibles ou causer des brûlures corporelles graves.
VORSICHT Bevor nach einem FRU-Austausch der Computer wieder angeschlossen wird, muß sichergestellt werden, daß keine Schrauben, Federn oder andere Kleinteile fehlen oder im Gehäuse vergessen wurden. Der Computer muß geschüttelt und auf Klappergeräusche geprüft werden. Metallteile oder-splitter können Kurzschlüsse erzeugen. VORSICHT Die Bereitschaftsbatterie, die sich unter dem Diskettenlaufwerk befindet, kann geringe Mengen Nickel und Cadmium enthalten.
VORSICHT Die Leuchtstoffröhre im LCD-Bildschirm enthält Quecksilber. Bei der Entsorgung die örtlichen Bestimmungen für Sondermüll beachten. Der LCD-Bildschirm besteht aus Glas und kann zerbrechen, wenn er unsachgemäß behandelt wird oder der Computer auf den Boden fällt.
18 ThinkPad R500 Hardware Maintenance Manual
Safety information 19
20 ThinkPad R500 Hardware Maintenance Manual
Safety information 21
22 ThinkPad R500 Hardware Maintenance Manual
Safety information 23
PELIGRO Antes de encender el sistema despues de sustituir una FRU, compruebe que todos los tornillos, muelles y demás piezas pequeñas se encuentran en su sitio y no se encuentran sueltas dentro del sistema. Compruébelo agitando el sistema y escuchando los posibles ruidos que provocarían. Las piezas metálicas pueden causar cortocircuitos eléctricos. PELIGRO Algunas baterías de reserva contienen una pequeña cantidad de níquel y cadmio.
PELIGRO Para evitar descargas, no quite la cubierta de plástico que rodea la parte baja de la tarjeta invertida. PELIGRO Aunque las baterías principales tienen un voltaje bajo, una batería cortocircuitada o con contacto a tierra puede producir la corriente suficiente como para quemar material combustible o provocar quemaduras en el personal.
26 ThinkPad R500 Hardware Maintenance Manual
Safety information 27
Laser compliance statement (multilingual translations) The laser compliance statements in this section are provided in the following languages: v English v Arabic v Brazilian Portuguese v French v German v Hebrew v Japanese v Korean v Spanish v Traditional Chinese Some models of ThinkPad Notebook are equipped from the factory with an optical storage device such as a CD-ROM drive or a DVD-ROM drive. Such devices are also sold separately as options.
Safety information 29
Alguns modelos de computador ThinkPad são equipados na fábrica com um dispositivo de armazenamento ótico, como uma unidade de CD-ROM ou de DVD-ROM. Tais dispositivos também são vendidos separadamente como opcionais. Se uma dessas unidades estiver instalada, ela é certificada nos Estados Unidos em conformidade com os requisitos do Department of Health and Human Services 21 Code of Federal Regulations (DHHS 21 CFR), Subcapítulo J, para produtos a laser da Classe 1.
Certains modèles d’ordinateur ThinkPad sont équipés d’origine d’une unité de stockage optique telle qu’une unité de CD-ROM ou de DVD-ROM. Ces unités sont également vendues séparément en tant qu’options. Si l’une de ces unités est installée, elle est certifiée conforme, aux Etats-Unis, aux normes indiquées dans le sous-chapitre J du DHHS 21 CFR relatif aux produits à laser de classe 1.
Einige ThinkPad-Modelle sind werkseitig mit einem CD-ROM- oder DVD-ROM-Laufwerk ausgestattet. CD- und DVD-Laufwerke können auch gesondert als Zusatzeinrichtung erworben werden. Die Laufwerke erfüllen die Anforderungen gemäß IEC 60825-1 (International Electrotechnical Commission) und gemäß CENELEC EN 60825-1 für Laserprodukte der Klasse 1.
Safety information 33
34 ThinkPad R500 Hardware Maintenance Manual
Safety information 35
Algunos modelos de sistemas ThinkPad están equipados de fábrica con un dispositivo de almacenamiento óptico, como una unidad de CD-ROM o de DVD-ROM. Estas unidades también se venden por separado como opciones. Si está instalada alguna de dichas unidades, se certifica que en los Estados Unidos cumple los requisitos del Department of Health and Human Services 21 Code of Federal Regulations (DHHS 21 CFR) Subchapter J para productos láser de Clase 1.
Safety information 37
38 ThinkPad R500 Hardware Maintenance Manual
Important service information This chapter presents following important service information that applies to all machine types supported by this manual: v “Strategy for replacing FRUs” – “Strategy for replacing a hard disk drive” on page 40 – “Important notice for replacing a system board” on page 40 – “How to use error message” on page 40 v “Strategy for replacing FRUs for CTO, CMV, and GAV” on page 41 – “Product definition” on page 41 – “FRU identification for CTO, CMV, and GAV products” on page 41 Import
Use the following strategy to prevent unnecessary expense for replacing and servicing FRUs: v If you are instructed to replace a FRU but the replacement does not correct the problem, reinstall the original FRU before you continue. v Some computers have both a processor board and a system board. If you are instructed to replace either the processor board or the system board, and replacing one of them does not correct the problem, reinstall that board, and then replace the other one.
Strategy for replacing FRUs for CTO, CMV, and GAV Product definition Dynamic Configure To Order (CTO) This provides the ability for a customer to configure an IBM® or a Lenovo solution from an eSite, and have this configuration sent to fulfillment, where it is built and shipped directly to the customer. The machine label, Product Entitlement Warehouse (PEW), eSupport, and the HMM will load these products as the 4-digit MT and 3-digit model, where model = “CTO” (Example: 1829-CTO).
v Business Partners using Eclaim will access PEW when performing Entitlement Lookup. Business Partners will enter Loc ID, MT and Serial, and the key commodities will be returned in the Eclaim record under SYSTEM DETAILS. v Authorized IBM Business Partners can access Eclaim at the following Web site: https://wca.eclaim.
General checkout This chapter presents following information: v “What to do first” on page 44 v “Checkout guide” on page 45 – “Diagnostics using PC-Doctor for DOS” on page 45 – “Lenovo ThinkVantage Toolbox (Lenovo System Toolbox)” on page 48 – “PC-Doctor for Windows” on page 48 – “PC-Doctor for Rescue and Recovery” on page 49 v “Power system checkout” on page 52 The descriptions in this chapter apply to any ThinkPad model that supports the PC-Doctor® for DOS diagnostics program.
What to do first When you do return a FRU, you must include the following information in the parts exchange form or parts return form that you attach to it: __ 1. Name and phone number of service technician __ 2. Date of service __ 3. Date on which the machine failed __ 4. Date of purchase __ 5. Failure symptoms, error codes appearing on the display, and beep symptoms __ 6. Procedure index and page number in which the failing FRU was detected __ 7. Failing FRU name and part number __ 8.
Checkout guide Use the following procedures as a guide in identifying and correcting problems with the ThinkPad Notebook. Note: The diagnostic tests are intended to test only ThinkPad products. The use of non-ThinkPad products, prototype cards, or modified options can lead to false indications of errors and invalid system responses. 1. Identify the failing symptoms in as much detail as possible. 2. Verify the symptoms.
Testing the computer Note: The PC-Doctor diagnostic CD does not support any optical drives connected through USB devices or any others. It supports only the internal optical drive of the ThinkPad Notebook. To run the test, do as follows: 1. Turn off the computer. 2. Make sure that the internal optical drive that is supported as a startup device is attached to the computer. 3. Turn on the computer. If the computer cannot be powered on, go to “Power system checkout” on page 52, and check the power sources.
The options on the test menu are as follows: Diagnostics v v v v v v v v v v v v v v Run Normal Test Run Quick Test CPU/Coprocessor Systemboard Video Adapter Serial Ports Parallel Ports Fixed Disks Diskette Drives Other Devices ThinkPad Devices Communication Wireless LAN Advanced Memory Tests Interactive Tests v v v v v v v v Keyboard Video Internal Speaker Mouse Diskette System Load Optical Drive Test Intel WLAN Radio Test Notes: v In the Keyboard test in Interactive Tests, the Fn key should be held do
v v v v v v v v DOS Shell Tech Support Form Battery Rundown View Test Log Print Log Save Log Full Erase Hard Drive Quick Erase Hard Drive Lenovo ThinkVantage Toolbox (Lenovo System Toolbox) Lenovo ThinkVantage® Toolbox (Lenovo System Toolbox in Windows Vista® and Windows® XP) is a diagnostic program that works through the Windows operating system.
v System Reports v Updates and Support PC-Doctor for Rescue and Recovery In some models of ThinkPad Notebook, the Rescue and Recovery® workspace enables you to run the PC-Doctor program to test the hardware features of the computer. To run the test, click “Run Diagnostics” on the Rescue and Recovery main screen.
FRU tests The following table shows the test for each FRU. Table 1. FRU tests FRU Applicable test System board 1. Diagnostics --> CPU/Coprocessor 2. Diagnostics --> Systemboard 3. If the docking station or the port replicator is attached to the ThinkPad computer, detach it. Place the computer on a horizontal surface, and run Diagnostics --> ThinkPad Devices --> HDD Active Protection Test. Note: Do not apply any physical shock to the computer while the test is running.
Table 1. FRU tests (continued) FRU Applicable test Memory 1. If two DIMMs are installed, remove one of them and run Diagnostics --> Advanced Memory Tests. 2. If the problem does not recur, return the DIMM to its place, remove the other one, and run the test again. Fan 1. Turn on the computer and check the air turbulence at the louver near the PC Card slot. 2. Run Diagnostics --> ThinkPad Devices --> Fan.
Power system checkout To 1. 2. 3. 4. 5. 6. 7. verify a symptom, do the following: Turn off the computer. Remove the battery pack. Connect the ac adapter. Check that power is supplied when you turn on the computer. Turn off the computer. Disconnect the ac adapter and install the charged battery pack. Check that the battery pack supplies power when you turn on the computer.
Checking operational charging To check whether the battery charges properly during operation, use a discharged battery pack or a battery pack that has less than 50% of the total power remaining when installed in the computer. Perform operational charging. If the battery status indicator or icon does not turn on, remove the battery pack and let it return to room temperature. Reinstall the battery pack. If the charge indicator or icon still does not turn on, replace the battery pack.
Checking the backup battery Do the following: 1. Power off the computer, and unplug the ac adapter from it. 2. Turn the computer upside down. 3. Remove the battery pack (see “1010 Battery pack” on page 84). 4. Remove the backup battery (see “1090 Backup battery” on page 99). 5. Measure the voltage of the backup battery. See the following figure. Red (+) Black (-) Wire Voltage (V dc) Red +2.5 to +3.2 Black Ground v If the voltage is correct, replace the system board.
Related service information This chapter presents following information: v “Restoring the factory contents by using Product Recovery discs” v “Restoring the factory contents by using Recovery Disc Set” on page 56 v “Passwords” on page 57 v “Power management” on page 60 v “Symptom-to-FRU index” on page 62 Service Web site: When the latest maintenance diskette and the system program service diskette become available, they will be posted on http://www.lenovo.
8. When the recovery process is complete, the Welcome to Microsoft Windows screen is displayed. Follow the instructions on the screen to complete the Windows setup. Restoring the factory contents by using Recovery Disc Set When the hard disk drive is replaced because of a failure, no product recovery program is on the new hard disk. In this case, you must use the Recovery Disc Set for the computer.
5. Read the license. If you agree with the terms and conditions, select I accept these terms and conditions and then click Next. If you do not agree with the terms and conditions, follow the instructions on the screen. 6. Click Yes in the displayed window to begin the operating system recovery process. 7. Insert the Applications and Drivers Recovery Disc when prompted and then click OK to begin the applications and drivers recovery process. 8.
Note: There are two modes for the HDP: User only and Master + User. The Master + User mode requires two HDPs; the system administrator enters both in the same operation. The system administrator then provides the user HDP to the system user. Attention: If the user HDP has been forgotten, check whether a master HDP has been set. If it has, it can be used for access to the hard disk drive.
5. Select Power-On Password. 6. Type the current SVP in the Enter Current Password field. then leave the Enter New Password field blank, and press Enter twice. 7. In the Changes have been saved window, press Enter. 8. Press F10; then, in the Setup confirmation window, select Yes.
Power management To reduce power consumption, the computer has three power management modes: screen blank, sleep (standby in Windows XP), and hibernation. Screen blank mode If the time set on the “Turn off monitor” timer in the operating system expires, the LCD backlight turns off. To put the computer into screen blank mode, do as follows: 1. Press Fn+F3. A panel for selecting a power plan (in Windows XP, power scheme) appears. 2.
Also, in either of the following events, the computer automatically returns from sleep (standby) mode and resumes operation: v The ring indicator (RI) is signaled by a serial device or a PC Card device. v The time set on the resume timer elapses. Note: The computer does not accept any input immediately after it enters sleep (standby) mode. Wait a few seconds before taking any action to reenter operation mode.
Symptom-to-FRU index This section contains following information: v “Numeric error codes” v “Error messages” on page 66 v “Beep symptoms” on page 67 v “No-beep symptoms” on page 67 v “LCD-related symptoms” on page 68 v “Intermittent problems” on page 69 v “Undetermined problems” on page 69 The symptom-to-FRU index in this section lists symptoms and errors and their possible causes. The most likely cause is listed first, in boldface type.
Table 2. Numeric error codes (continued) Symptom or error FRU or action, in sequence 0187 EAIA data access error—The access to EEPROM is failed. System board. 0188 Invalid RFID Serialization Information Area. System board. 0189 System board. Invalid RFID configuration information area—The EEPROM checksum is not correct. 0190 Critical low-battery error 1. Charge the battery pack. 2. Battery pack. 0191 System Security—Invalid Remote Change requested. 1.
Table 2. Numeric error codes (continued) 64 Symptom or error FRU or action, in sequence 0250 System battery error—System battery is dead. 1. Charge the backup battery for more than 8 hours by connecting the ac adapter. 2. Replace the backup battery and run BIOS Setup Utility to reset the time and date. 0251 System CMOS checksum bad— Default configuration used. 1. Charge the backup battery for more than 8 hours by connecting the ac adapter. 2.
Table 2. Numeric error codes (continued) Symptom or error FRU or action, in sequence 1804 Unauthorized WAN card is plugged in—Power off and remove the WAN card. 1. Remove the WAN card that you installed. 2. System board. 1805 Unauthorized Wireless USB card is plugged in—Power off and remove the Wireless USB card. 1. Remove the Wireless USB card that you installed. 2. System board. 1820 More than one external fingerprint reader is attached.
Error messages Table 3. Error messages Symptom or error FRU or action, in sequence Device address conflict. 1. Load “Setup Defaults” in the BIOS Setup Utility. 2. Backup battery. 3. System board. Allocation error for device. 1. Load “Setup Defaults” in the BIOS Setup Utility. 2. Backup battery. 3. System board. Failing bits: nnnn. 1. DIMM. 2. System board. Invalid system configuration data. 1. DIMM. 2. System board. I/O device IRQ conflict. 1. Load “Setup Defaults” in the BIOS Setup Utility. 2.
Beep symptoms Table 4. Beep symptoms Symptom or error FRU or action, in sequence One beep and a blank, unreadable, or flashing LCD. 1. 2. 3. 4. One long and two short beeps, and a blank or unreadable LCD. 1. System board. 2. LCD assembly. 3. DIMM. Two short beeps with error codes. POST error. See “Numeric error codes” on page 62. Two short beeps and a blank screen. 1. System board. 2. DIMM. Three short beeps, pause, three more short beeps, and one short beep. 1. DIMM. 2.
LCD-related symptoms Important: The TFT LCD for the notebook computer contains many thin-film transistors (TFTs). The presence of a small number of dots that are missing, discolored, or always lighted is characteristic of TFT LCD technology, but excessive pixel problems can cause viewing concerns. If the LCD you are servicing has two or less visible defective pixels, it should not be considered faulty.
Intermittent problems Intermittent system hang problems can be due to a variety of causes that have nothing to do with a hardware defect, such as cosmic radiation, electrostatic discharge, or software errors. FRU replacement should be considered only when a problem recurs. When analyzing an intermittent problem, do the following: 1. Run the diagnostic test for the system board in loop mode at least 10 times. 2. If no error is detected, do not replace any FRUs. 3.
70 ThinkPad R500 Hardware Maintenance Manual
Status indicators This chapter presents the system status indicators that show the status of the computer.
Table 7. Status indicators Indicator Meaning 1 Wireless LAN status Green: The LAN wireless feature is on, and the radio link is ready for use. Blinking green: Data is being transmitted. 2 Bluetooth status Green: Bluetooth wireless is operational. This indicator is on when Bluetooth wireless is on and not in suspend mode. R 72 3 Num lock Green: The numeric keypad on the keyboard is enabled. To enable or disable the keypad, press and hold the Shift key, and press the NumLk (ScrLk) key.
Table 7. Status indicators (continued) Indicator 10 Meaning Serial Ultrabay Green: A Serial Ultrabay Enhanced device is installed and in Enhanced status use. Blinking green: A Serial Ultrabay Enhanced device is in the process of being detached. Turn off: A Serial Ultrabay Enhanced device is ready to be attached or detached. Note: If you are using Windows 2000, the Serial Ultrabay Enhanced status indicator does not blink while a Serial Ultrabay Enhanced device is being detached.
74 ThinkPad R500 Hardware Maintenance Manual
Fn key combinations The following table shows the function of each combination of Fn with a function key. Table 8. Fn key combinations Key combination Description Fn+F1 Reserved. Fn+F2 Lock the computer. Fn+F3 Select a power plan (in Windows XP, power scheme) that has been created by Power Manager, or adjust the power level by using the slider control. When you press this combination, a panel for selecting a power plan (power scheme) appears. Notes: 1.
Table 8. Fn key combinations (continued) Key combination Description Fn+F7 Apply a presentation scheme directly, with no need to start Presentation Director. To disable this function and use the Fn+F7 key combination for switching a display output location, start Presentation Director, and change the settings. Note: If the computer is a windows 7 model, it does not support presentation schemes, but the Fn+F7 combination is available for switching a display output location.
Table 8. Fn key combinations (continued) Key combination Description Fn+F10 Reserved. Fn+F11 Reserved. Fn+F12 Put the computer into hibernation mode. To return to normal operation, press the power button for less than four seconds. Note: To use Fn+F12 for hibernation, you must have the ThinkPad PM device driver installed on the computer. Fn+PgUp Turn the ThinkLight® on or off. Note: This function is supported only on the ThinkPad computers that have the ThinkLight.
78 ThinkPad R500 Hardware Maintenance Manual
FRU replacement notices This chapter presents notices related to removing and replacing parts. Read this chapter carefully before replacing any FRU. Screw notices Loose screws can cause a reliability problem. In the ThinkPad Notebook, this problem is addressed with special nylon-coated screws that have the following characteristics: v They maintain tight connections. v They do not easily come loose, even with shock or vibration. v They are harder to tighten. v Each one should be used only once.
Retaining serial numbers This section includes the following descriptions: v “Restoring the serial number of the system unit” v “Retaining the UUID” v “Reading or writing the ECA information” on page 81 Restoring the serial number of the system unit When the computer was manufactured, the EEPROM on the system board was loaded with the serial numbers of the system and all major components. These numbers need to remain the same throughout the life of the computer.
The algorithm that generates the number is designed to provide unique IDs until the year A.D. 3400. No two computers in the world have the same number. When you replace the system board, you must set the UUID on the new system board as follows: 1. Install the ThinkPad Hardware Maintenance Diskette Version 1.73 or later, and restart the computer. 2. From the main menu, select 4. Assign UUID. A new UUID is created and written. If a valid UUID already exists, it is not overwritten.
82 ThinkPad R500 Hardware Maintenance Manual
Removing and replacing a FRU This chapter presents directions and drawings for use in removing and replacing a FRU. Be sure to observe the following general rules: 1. Do not try to service any computer unless you have been trained and certified. An untrained person runs the risk of damaging parts. 2. Before replacing any FRU, review “FRU replacement notices” on page 79. 3. Begin by removing any FRUs that have to be removed before the failing FRU. Any such FRUs are listed at the top of the page.
1010 Battery pack Important notice for replacing a battery pack: ThinkVantage Toolbox (in Windows 7) and Lenovo System Toolbox (in Windows Vista and Windows XP) have an automatic battery diagnostic that determines if the battery pack is defective. A battery pack FRU should not be replaced unless this diagnostic shows that the battery is defective. The only exception to this is if the battery pack is physically damaged or a customer is reporting a possible safety issue.
1020 Serial Ultrabay Enhanced device Note: Serial Ultrabay Enhanced does not accept any of the following devices: v Ultrabay PlusTM devices v Ultrabay 2000TM devices Table 10. Removal steps of Serial Ultrabay Enhanced device for R61 and R61i When you release the switch in step 1 , the lever pops out. In step 2 , pull the lever a little to release the device from the bay.
1030 Hard disk drive cover, hard disk drive, and hard disk rubber rails For access, remove these FRUs, in order: v “1010 Battery pack” on page 84 Attention: v Do not drop the hard disk drive or apply any physical shock to it. The hard disk drive is sensitive to physical shock. Improper handling can cause damage and permanent loss of data. v Before removing the drive, have the user make a backup copy of all the information on it if possible.
Table 11. Removal steps of hard disk drive cover, hard disk drive, and hard disk rubber rails (continued) 4 5 3 When installing: Make sure that the hard disk drive connector is attached firmly. 6 6 When installing: The rubber rails on the hard disk drive must be attached to the replacement drive. Otherwise the drive cannot be installed properly.
1040 Palm rest or palm rest with fingerprint reader For access, remove these FRUs, in order: v “1010 Battery pack” on page 84 Note: In models with the fingerprint reader, the sensor is attached to the palm rest FRU. If the fingerprint reader has any defects, you can replace it by the procedures given in this section, which are the same for a palm rest with or without a fingerprint reader. Table 12.
Table 12. Removal steps of palm rest (continued) 2 2 3 When installing: When you attach the palm rest, do as follows: 1. Attach the fingerprint reader connector firmly to the system board.
Table 12. Removal steps of palm rest (continued) 2. Attach the palm rest so that the two projections of the palm rest ( a ) firmly fit into the guide holes of the keyboard bezel as shown in this figure. a a 3. Push the front side of the palm rest until it clicks into place. 4. Close the LCD cover and turn the computer over. Then fasten the four screws to secure the palm rest.
1050 DIMM For access, remove these FRUs, in order: v “1010 Battery pack” on page 84 v “1040 Palm rest or palm rest with fingerprint reader” on page 88 Table 13. Removal steps of dimm Note: If only one DIMM is used on the computer you are servicing, the card must be installed in SLOT-0 ( a ), but not in SLOT-1 ( b ). 1 b 2 a 1 When installing: Insert the notched end of the DIMM into the socket. Press the DIMM firmly, and pivot it until it snaps into the place.
1060 Keyboard For access, remove these FRUs, in order: v “1010 Battery pack” on page 84 v “1040 Palm rest or palm rest with fingerprint reader” on page 88 Table 14. Removal steps of keyboard 1 Step Icon 1 Screw (quantity) Color Torque M2 × 17 mm, flat-head, nylon-coated (1) Black 0.167 Nm (1.7 kgfcm) Lift the keyboard a little in the direction shown by arrow 2 , and then detach the connector 3 .
Table 14. Removal steps of keyboard (continued) When installing: Make sure that the keyboard edges a are under the frame as shown in this figure.
1070 PCI Express Mini Card for wireless LAN For access, remove these FRUs, in order: v “1010 Battery pack” on page 84 v “1040 Palm rest or palm rest with fingerprint reader” on page 88 v “1060 Keyboard” on page 92 Table 15. Removal steps of PCI Express Mini Card for wireless LAN Full size PCI Express Mini card: . In step 1 , unplug the jacks by using the removal tool antenna RF connector (P/N: 08K7159) or pick the connectors with your fingers and gently unplug them in direction of the arrow.
Table 15. Removal steps of PCI Express Mini Card for wireless LAN (continued) 3 When installing: In models with wireless LAN card that has two antenna connectors, plug the gray cable into the jack labeled MAIN or M on the card, and the black cable into the jack labeled AUX or A. If the computer you are servicing has three cables, put the white cable in the cable protection tube.
Table 15. Removal steps of PCI Express Mini Card for wireless LAN (continued) Half size PCI Express Mini card: In step 1 , unplug the jacks by using the removal tool antenna RF connector (P/N: 08K7159) or pick the connectors with your fingers and gently unplug them in direction of the arrow. 2 2 1 Step Screw (quantity) Color Torque 2 M2 × 3 mm, flat-head, nylon-coated (2) Silver 0.167 Nm (1.
Table 15. Removal steps of PCI Express Mini Card for wireless LAN (continued) When installing: Plug the gray cable into the jack labeled MAIN on the card, and the black cable into the jack labeled AUX.
1080 Intel Turbo Memory Minicard For access, remove these FRUs, in order: v “1010 Battery pack” on page 84 v “1040 Palm rest or palm rest with fingerprint reader” on page 88 v “1060 Keyboard” on page 92 Table 16. Removal steps of Intel Turbo Memory 1 1 2 Step Screw (quantity) Color Torque 1 M2 × 3 mm, flat-head, nylon-coated (2) Silver 0.167 Nm (1.
1090 Backup battery DANGER Use only the battery specified in the parts list for your computer. Any other battery could ignite or explode. For access, remove these FRUs in order: v “1010 Battery pack” on page 84 v “1040 Palm rest or palm rest with fingerprint reader” on page 88 v “1060 Keyboard” on page 92 Table 17. Removal steps of backup battery 1 2 When installing: Make sure that the battery connector is attached firmly.
1100 Keyboard bezel and speakers For access, remove these FRUs, in order: v “1010 Battery pack” on page 84 v “1040 Palm rest or palm rest with fingerprint reader” on page 88 v “1060 Keyboard” on page 92 Table 18. Removal steps of keyboard bezel and speakers Note: Speakers are attached to the underside of the keyboard bezel. 1 Step Screw (quantity) Color Torque 1 M2 × 3 mm, flat-head, nylon-coated (1) Silver 0.167 Nm (1.
Table 18. Removal steps of keyboard bezel and speakers (continued) 4 4 4 3 4 4 4 In step 3 , release the wireless antenna cables from the cable guide. Step Screw (quantity) Color Torque 4 M2 × 3 mm, flat-head, nylon-coated (6) Silver 0.167 Nm (1.7 kgfcm) In step 5 , strip the securing tapes off. Then detach the speaker connector 6 . 5 5 5 5 5 5 6 When installing: Make sure that speaker connector is attached firmly.
Table 18. Removal steps of keyboard bezel and speakers (continued) In step 7 , detach the claws. Then remove the keyboard bezel in the direction shown by arrow 8 . 7 7 8 7 7 8 When installing: Make sure that all the claws are attached firmly. 9 10 9 9 10 9 102 Step Screw (quantity) Color Torque 9 M2 × 3 mm, flat-head, nylon-coated (4) Silver 0.167 Nm (1.
0 Fan assembly For access, remove these FRUs, in order: v “1010 Battery pack” on page 84 v “1040 Palm rest or palm rest with fingerprint reader” on page 88 v “1060 Keyboard” on page 92 v “1100 Keyboard bezel and speakers” on page 100 Table 19. Removal steps of fan assembly 2 3 2 1 3 1 Step Screw (quantity) Color Torque 1 M2 × 3 mm, flat-head, nylon-coated (2) Silver 0.167 Nm (1.7 kgfcm) 2 M2 × 9.5 mm, flat-head, nylon-coated (2) Black 0.167 Nm (1.
Table 19. Removal steps of fan assembly (continued) Attention: Do not handle the fan roughly. Improper handling of the fan can cause distortion or deformation and imperfect contact with components. 5 4 4 4 Step Screw (quantity) Color Torque 4 M2 × 9.5 mm, flat-head, nylon-coated (2) Black 0.167 Nm (1.7 kgfcm) In step 5 , release the wireless antenna cables from the cable guide of the fan assembly.
Table 19. Removal steps of fan assembly (continued) When installing: v Before you attach the fan assembly to the computer, apply thermal grease, at an amount of 0.2 grams, on the part marked a as in the following figure. Either too much or too less application of grease can cause a thermal problem due to imperfect contact with a component. In some modes, you need to peel the thin film off from the rubber b .
Table 19. Removal steps of fan assembly (continued) v Make sure that the fan connector is attached firmly. v When attaching the fan assembly to the frame, take care not to damage the heat sink ( b ) of the fan assembly.
1120 CPU For access, remove these FRUs, in order: v “1010 Battery pack” on page 84 v “1040 Palm rest or palm rest with fingerprint reader” on page 88 v “1060 Keyboard” on page 92 v “1100 Keyboard bezel and speakers” on page 100 v “1110 Fan assembly” on page 103 Table 20. Removal steps of CPU Attention: CPU is extremely sensitive. When you service the CPU, avoid any kind of rough handling. Rotate the head of the screw in the direction shown by arrow 1 to release the lock; then remove the CPU.
1130 LCD assembly For access, remove these FRUs, in order: v “1010 Battery pack” on page 84 v “1040 Palm rest or palm rest with fingerprint reader” on page 88 v “1060 Keyboard” on page 92 v “1070 PCI Express Mini Card for wireless LAN” on page 94 v “1100 Keyboard bezel and speakers” on page 100 Table 21. Removal steps of LCD assembly 1 1 108 Step Screw (quantity) Color Torque 1 M2 × 9.5 mm, flat-head, nylon-coated (2) Black 0.167 Nm (1.
Table 21. Removal steps of LCD assembly (continued) 4 4 4 3 2 3 Step Screw (quantity) Color Torque 3 M2.5 × 6.5 mm, flat-head, nylon-coated (2) Black 0.167 Nm (1.7 kgfcm) In step 4 , strip off the tapes securing the antenna cables, and release the cables from the cable guides of the frame.
Table 21. Removal steps of LCD assembly (continued) 5 5 When installing: 1. Route the antenna cables along the cable guides and secure them with the tapes. As you route the cables, make sure that they are not subjected to any tension. Tension could cause the cables to be damaged by the cable guides, or a wire to be broken. 2. Make sure that the LCD connector is attached firmly.
1140 Base cover and PC Card/ExpressCard (or ExpressCard/Smart Card) bezel assembly For access, remove these FRUs, in order: v “1010 Battery pack” on page 84 v “1020 Serial Ultrabay Enhanced device” on page 85 v “1030 Hard disk drive cover, hard disk drive, and hard disk rubber rails” on page 86 v “1040 Palm rest or palm rest with fingerprint reader” on page 88 v “1060 Keyboard” on page 92 v “1070 PCI Express Mini Card for wireless LAN” on page 94 v “1100 Keyboard bezel and speakers” on page 100 v “1130 LCD
Table 22. Removal steps of base cover and PC Card/ExpressCard (or ExpressCard/Smart Card) bezel assembly (continued) 3 3 4 112 4 Step Screw (quantity) Color Torque 3 M2 × 9.5 mm, flat-head, nylon-coated (1) Black 0.167 Nm (1.7 kgfcm) 4 M2 × 17 mm, flat-head, nylon-coated (2) Black 0.167 Nm (1.
Table 22. Removal steps of base cover and PC Card/ExpressCard (or ExpressCard/Smart Card) bezel assembly (continued) 6 7 5 8 5 Step Screw (quantity) Color Torque 5 M2 × 5 mm, flat-head, nylon-coated (2) Black 0.167 Nm(1.
Table 22. Removal steps of base cover and PC Card/ExpressCard (or ExpressCard/Smart Card) bezel assembly (continued) Attention: Before step 7 , be sure that the Serial Ultrabay Enhanced device eject lever has not popped out. It must be housed in its position as shown in the figure a . 7 8 b a When installing: Check the position of the wireless switch b , and firmly fit the structure frame into the base cover.
Table 22. Removal steps of base cover and PC Card/ExpressCard (or ExpressCard/Smart Card) bezel assembly (continued) Remove the security hole bracket as in this figure. 1 2 Step Screw (quantity) Color Torque 1 M2 × 3 mm, flat-head, nylon-coated (1) Silver 0.167 Nm(1.
Table 22. Removal steps of base cover and PC Card/ExpressCard (or ExpressCard/Smart Card) bezel assembly (continued) Remove the RJ11 cable a and the optical drive switch cable b as in this figure. In step 2 , strip the securing taps off. a b 5 4 3 3 2 2 116 Step Screw (quantity) Color Torque 3 M2 × 3 mm, flat-head, nylon-coated (2) Silver 0.167 Nm(1.
Table 22. Removal steps of base cover and PC Card/ExpressCard (or ExpressCard/Smart Card) bezel assembly (continued) When removing the PC Card/ExpressCard bezel assembly, do as shown in this figure. 1 2 When removing the ExpressCard/Smart Card bezel assembly, do as shown in this figure.
Applying labels to the base cover: The new base cover FRU is shipped with a kit containing labels of several kinds. When you replace the base cover, you need to apply the following label: 1 Product label 1a Non-mercury label Note: If the computer you are servicing is an LED-backlight LCD model, you need to paste this label so that the notice for mercury on the product label is covered.
1150 Structure frame and IEEE 1394 sub card For access, remove these FRUs, in order: v “1010 Battery pack” on page 84 v “1020 Serial Ultrabay Enhanced device” on page 85 v “1030 Hard disk drive cover, hard disk drive, and hard disk rubber rails” on page 86 v “1040 Palm rest or palm rest with fingerprint reader” on page 88 v “1060 Keyboard” on page 92 v “1070 PCI Express Mini Card for wireless LAN” on page 94 v “1100 Keyboard bezel and speakers” on page 100 v “1110 Fan assembly” on page 103 v “1130 LCD assem
Table 23. Removal steps of structure frame and IEEE 1394 sub card (continued) Remove the ac power jack cable a . 3 a 2 When installing: Make sure the connectors are attached firmly.
Table 23. Removal steps of structure frame and IEEE 1394 sub card (continued) Remove the CPU support plate. 6 Step Screw (quantity) Color Torque 6 M2 × 5 mm, flat-head, nylon-coated (1) Black 0.167 Nm (1.
Table 23. Removal steps of structure frame and IEEE 1394 sub card (continued) 8 7 7 7 7 a Step Screw (quantity) Color Torque 7 M2 × 3.5 mm, bind-head, nylon-coated (4) Black 0.167 Nm (1.7 kgfcm) 8 M2 × 9.5 mm, flat-head, nylon-coated (1) Black 0.167 Nm (1.7 kgfcm) When installing: When attaching the system board to the frame, adjust the placement with the small projection a . Then secure the system board with the screws.
Table 23. Removal steps of structure frame and IEEE 1394 sub card (continued) In step 10 , remove the system board and the PC Card/ExpressCard slots assembly from the structure frame together. In step 11 and 12 , remove IEEE 1394 sub card. 10 9 11 12 Step Screw (quantity) Color Torque 11 M2 × 5 mm, flat-head, nylon-coated (1) Black 0.167 Nm (1.
1160 System board, PC Card/ExpressCard slots (or ExpressCard/Smart Card slots) assembly Important notices for handling the system board: When handling the system board, bear the following in mind. v At every point in the process, be sure not to drop or stack the system board. v The system board has an accelerometer, which can be broken by applying several thousands of G-forces.
Following components soldered on the top side of the system board are extremely sensitive. When you service the system board, avoid any kind of rough handling. a CPU b Video chip (Discrete graphics chip models only.) c MCH (Memory Controller Hub) d ICH (I/O Controller Hub) e Accelerometer chip for the HDD Active Protection SystemTM a b c d e Table 24.
Table 24. Removal steps system board, PC Card/ExpressCard slots (ExpressCard/Smart Card slots) assembly (continued) Turn the system board over, and then disconnect the PC Card/ExpressCard slots (or ExpressCard/Smart Card slots) assembly a from the system board. a 2 When installing: Make sure that the connector of the PC Card/Express Card slots (ExpressCard/Smart Card slots) assembly is attached to the system board firmly.
2010 LCD front bezel For access, remove these FRUs, in order: v “1010 Battery pack” on page 84 Table 25. Removal steps of LCD front bezel 1 2 1 2 2 Step Screw cap Screw (quantity) Color Torque 1 M2.5 × 6.5 mm, flat-head, nylon-coated (2) Black 0.392 Nm (4 kgfcm) 2 M2.5 × 6.5 mm, flat-head, nylon-coated (3) Black 0.392 Nm (4 kgfcm) In step 3 , detach the claws. Then remove the LCD front bezel. Note: The LCD front bezel is secured with a double-faced adhesive tape.
2020 Inverter card or LED control card For access, remove these FRUs, in order: v “1010 Battery pack” on page 84 v “2010 LCD front bezel” on page 127 Table 26. Removal steps of inverter card or LED control card 2 1 4 3 Step Screw (quantity) Color Torque 1 M2 × 2.8 mm, flat-head, nylon-coated (1) Silver 0.167 Nm (1.7 kgfcm) When installing: Make sure that connectors 3 and 4 are attached firmly.
2030 Bluetooth daughter card (BDC-2.1) For access, remove these FRUs, in order: v “1010 Battery pack” on page 84 v “2010 LCD front bezel” on page 127 Table 27. Removal steps of Bluetooth daughter card 1 2 Step Screw (quantity) Color Torque 1 M2 × 2.8 mm, flat-head, nylon-coated (1) Black 0.167 Nm (1.7 kgfcm) When installing: Make sure that connector is attached firmly.
2040 Integrated camera For access, remove these FRUs, in order: v “1010 Battery pack” on page 84 v “2010 LCD front bezel” on page 127 Table 28. Removal steps of Integrated camera Note: The part marked a is fragile and might be damaged by rough handling. When you remove the camera, do not hold that part to avoid the damage. 1 a 3 2 Step Screw (quantity) Color Torque 1 M2 × 2.8 mm, flat-head, nylon-coated (1) Silver 0.167 Nm (1.
2050 LCD panel, LCD cable, hinges, and ALPET sheets For access, remove these FRUs, in order: v “1010 Battery pack” on page 84 v “1040 Palm rest or palm rest with fingerprint reader” on page 88 v “1060 Keyboard” on page 92 v “1070 PCI Express Mini Card for wireless LAN” on page 94 v “1100 Keyboard bezel and speakers” on page 100 v “1130 LCD assembly” on page 108 v “2010 LCD front bezel” on page 127 Table 29.
Table 29. Removal steps of LCD panel, LCD cable, hinges, and ALPET sheets (continued) Remove the hinges a . a 6 5 5 a 5 6 5 Step Screw (quantity) Color Torque 5 M2 × 2.8 mm, flat-head, nylon-coated (4) Silver 0.167 Nm (1.7 kgfcm) Cable routing: When you install the LCD panel, make sure that the antenna cables are routed as shown in this figure.
Table 29. Removal steps of LCD panel, LCD cable, hinges, and ALPET sheets (continued) Remove the ALPET sheets, b and c . 7 b Note: The ALPET sheets are secured with a double-faced adhesive tape.
Table 29. Removal steps of LCD panel, LCD cable, hinges, and ALPET sheets (continued) Remove the LCD cable d . 10 d 11 When installing: Make sure that the connector is attached firmly.
2060 LCD rear cover and wireless LAN antenna cables For access, remove these FRUs, in order: v “1010 Battery pack” on page 84 v “1040 Palm rest or palm rest with fingerprint reader” on page 88 v “1060 Keyboard” on page 92 v “1070 PCI Express Mini Card for wireless LAN” on page 94 v “1100 Keyboard bezel and speakers” on page 100 v “1130 LCD assembly” on page 108 v “2010 LCD front bezel” on page 127 v “2020 Inverter card or LED control card” on page 128 v “2030 Bluetooth daughter card (BDC-2.
136 ThinkPad R500 Hardware Maintenance Manual
Locations This chapter presents the location of ThinkPad R500 features and hardware. Front view 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 ThinkLight Integrated camera (for some models) Status indicators Note: For the description of each indicator, see “Status indicators” on page 71.
Rear view 1 2 3 4 5 6 7 8 9 10 Status indicators Note: For the description of each indicator, see “Status indicators” on page 71.
Bottom view 1 2 3 4 5 6 7 8 9 Battery pack Battery pack latch Docking connector Wireless radio switch Stereo headphone jack Microphone jack 7-in-1 Media Card Reader slot LCD cover latch Hard disk drive 1 2 3 9 8 7 6 5 4 Locations 139
140 ThinkPad R500 Hardware Maintenance Manual
Parts list This section contains following lists of the service parts. v “Overall” on page 142 v “LCD FRUs” on page 179 v “Keyboard” on page 190 v “Miscellaneous parts” on page 192 v “AC adapters” on page 194 v “Power cords” on page 195 v “Recovery discs” on page 196 v “Common service tools” on page 213 Notes: v Each FRU is available for all types or models, unless specific types or models are specified.
Overall 1 23 2 22 3 g a b f 21 c 20 4 19 18 5 17 16 6 7 15 8 e 9 14 10 d 13 11 12 142 ThinkPad R500 Hardware Maintenance Manual
Table 31. Parts list—Overall No. FRU a-g See “Miscellaneous parts” on page 192. FRU no. CRU ID 1 LCD unit (see “LCD FRUs” on page 179.
Table 31. Parts list—Overall (continued) No. FRU FRU no.
Table 31. Parts list—Overall (continued) No. FRU FRU no.
Table 31. Parts list—Overall (continued) No. FRU FRU no.
Table 31. Parts list—Overall (continued) No. FRU FRU no.
Table 31. Parts list—Overall (continued) No. FRU FRU no.
Table 31. Parts list—Overall (continued) No. FRU FRU no.
Table 31. Parts list—Overall (continued) No. FRU FRU no.
Table 31. Parts list—Overall (continued) No. FRU FRU no.
Table 31. Parts list—Overall (continued) No. FRU FRU no. CRU ID 9 SATA hard disk drive, 160 GB, 7,200 rpm OP v 2713-CTO, 3Fx v 2714-CTO, 55x, 56x, 57x, 58x, 7Sx v 2716-CTO.
Table 31. Parts list—Overall (continued) No. FRU FRU no. CRU ID 9 SATA hard disk drive, 200 GB , FDE, 7,200 rpm OP v 2713-CTO v 2714-CTO v 2716-CTO v 2717-CTO v 2718-CTO, 4Gx, 4Jx, 72x, 74x v 2719-CTO v 2720-CTO v 2731-CTO v 2732-CTO v 2733-CTO, 3Kx, 3Px v 2734-CTO v 2735-CTO, 3Tx, 3Ux, 5Sx v 2736-CTO v 2737-CTO 42T1463 * 9 SATA hard disk drive, 200 GB , 9.
Table 31. Parts list—Overall (continued) No. FRU FRU no. CRU ID 9 SATA hard disk drive, 250 GB , 9.5 mm, FDE, 7,200 rpm v 2713-CTO v 2714-CTO v 2716-CTO, 8Ax, 8Ex v 2717-CTO v 2718-CTO, 8Fx, 8Kx v 2719-CTO v 2720-CTO v 2731-CTO v 2732-CTO v 2733-CTO, 6Ux v 2734-CTO v 2735-CTO, 6Zx v 2736-CTO v 2737-CTO 42T1573 * 9 SATA hard disk drive, 320 GB, 9.
Table 31. Parts list—Overall (continued) No. FRU FRU no. CRU ID 9 SATA hard disk drive, 500 GB, 7,200 rpm v 2713-CTO v 2714-CTO v 2716-CTO v 2717-CTO v 2718-CTO v 2719-CTO v 2720-CTO v 2731-CTO v 2732-CTO v 2733-CTO v 2734-CTO v 2735-CTO v 2736-CTO v 2737-CTO 45N7267 * 10 Battery pack, Li-ion (6 cell, 2.
Table 31. Parts list—Overall (continued) No. 10 156 FRU FRU no. 42T4671 Battery pack, Li-ion (6 cell, 2.
Table 31. Parts list—Overall (continued) No. 10 FRU FRU no. 42T4670 Battery pack, Li-ion (6 cell, 2.
Table 31. Parts list—Overall (continued) No. FRU FRU no. CRU ID 10 42T4651 Battery pack, Li-ion (6 cell, 2.
Table 31. Parts list—Overall (continued) No. FRU FRU no. CRU ID 10 Battery pack, Li-ion (6 cell, 2.6 Ah) v 2713-CTO v 2714-CTO v 2716-CTO v 2717-CTO v 2718-CTO v 2719-CTO v 2720-CTO v 2731-CTO v 2732-CTO v 2733-CTO v 2734-CTO v 2735-CTO v 2736-CTO v 2737-CTO 42T4621 * 10 Battery pack, Li-ion (6 cell, 2.
Table 31. Parts list—Overall (continued) No. FRU FRU no. CRU ID 10 Battery pack, Li-ion (9 cell, 2.
Table 31. Parts list—Overall (continued) No. FRU FRU no.
Table 31. Parts list—Overall (continued) No. 11 162 FRU FRU no.
Table 31. Parts list—Overall (continued) No. 11 FRU FRU no.
Table 31. Parts list—Overall (continued) No. 11 164 FRU FRU no.
Table 31. Parts list—Overall (continued) No. FRU FRU no.
Table 31. Parts list—Overall (continued) No. 11 11 FRU Blu-Ray disk v 2713-CTO v 2714-CTO, v 2716-CTO v 2717-CTO v 2718-CTO v 2719-CTO v 2720-CTO v 2731-CTO v 2732-CTO, v 2733-CTO v 2734-CTO v 2735-CTO, v 2736-CTO v 2737-CTO Travel cover v 2713-CTO, v 2714-CTO, v 2716-CTO, v 2717-CTO, v 2718-CTO, v 2719-CTO, v 2720-CTO, v 2731-CTO, v 2732-CTO, v 2733-CTO, v 2734-CTO, v 2735-CTO, v 2736-CTO, v 2737-CTO, drive FRU no.
Table 31. Parts list—Overall (continued) No. FRU FRU no.
Table 31. Parts list—Overall (continued) No. FRU FRU no.
Table 31. Parts list—Overall (continued) No. FRU FRU no.
Table 31. Parts list—Overall (continued) No. FRU FRU no.
Table 31. Parts list—Overall (continued) No. FRU FRU no. CRU ID 17 CPU assembly, Intel Celeron processor900 (2.2 GHz) v 2713-CTO, 97x, 98x v 2714-CTO, 92x, 93x, 94x, 95x, ARx v 2716-CTO, A5x v 2717-CTO v 2718-CTO, 9Bx, 9Cx v 2719-CTO v 2720-CTO 43R0795 N 17 CPU assembly, Intel Celeron processor T3000 (1.8 GHz) v 2713-CTO v 2714-CTO v 2716-CTO v 2717-CTO v 2718-CTO v 2719-CTO v 2720-CTO 43R0894 N 17 CPU assembly, Intel Celeron processor T3100 (1.
Table 31. Parts list—Overall (continued) No. FRU FRU no. CRU ID 17 42W7984 CPU assembly, Intel Core 2 Duo mobile processor P8400 (2.
Table 31. Parts list—Overall (continued) No. FRU FRU no. CRU ID 17 CPU assembly, Intel Core 2 Duo mobile processor P8800 (2.66 GHz) v 2713-CTO v 2714-CTO, AKx, ALx v 2716-CTO, 9Zx, A2x, A3x, A6x, ADx, AEx v 2717-CTO v 2718-CTO v 2719-CTO v 2720-CTO v 2731-CTO v 2732-CTO, 7Yx v 2733-CTO, 7Mx, 7Nx, 7Sx, 7Tx, 7Wx v 2734-CTO v 2735-CTO v 2736-CTO v 2737-CTO 45M2814 N 17 CPU assembly, Intel Core 2 Duo mobile processor T5670 (1.
Table 31. Parts list—Overall (continued) No. FRU FRU no. CRU ID 17 CPU assembly, Intel Core 2 Duo mobile processor T6570 (2.1 GHz) v 2713-CTO v 2714-CTO, 7Xx, 8Lx, 8Tx, 8Ux, 96x, 9Px v 2716-CTO, 8Bx v 2717-CTO, 8Vx v 2718-CTO, 8Gx v 2719-CTO v 2720-CTO v 2731-CTO v 2732-CTO, 6Hx, 6Jx, 6Kx, 6Lx, 7Fx, 84x v 2733-CTO, 6Wx v 2734-CTO v 2735-CTO, 72x v 2736-CTO v 2737-CTO 42W8193 N 17 CPU assembly, Intel Core 2 Duo mobile processor T6670 (2.
Table 31. Parts list—Overall (continued) No. FRU FRU no. CRU ID 17 CPU assembly, Intel Core 2 Duo mobile processor T9550 (2.66 GHz) v 2713-CTO v 2714-CTO v 2716-CTO, 85x, 86x, 8Ax v 2717-CTO v 2718-CTO, 8Fx v 2719-CTO v 2720-CTO v 2731-CTO v 2732-CTO v 2733-CTO, 6Qx, 6Rx, 6Sx, 6Ux, 7Dx v 2734-CTO v 2735-CTO, 6Zx v 2736-CTO v 2737-CTO 42W8195 N 17 CPU assembly, Intel Core 2 Duo mobile processor T9600 (2.
Table 31. Parts list—Overall (continued) No. FRU FRU no. CRU ID 17 CPU assembly, Intel Core 2 Duo mobile processor T9900 (3.
Table 31. Parts list—Overall (continued) No. FRU FRU no.
Table 31. Parts list—Overall (continued) No. FRU FRU no. CRU ID 21 Thermal device and fan (Integrated graphics) v 2713-all v 2714-all v 2716-all v 2717-all v 2718-all v 2719-CTO v 2720-CTO 44C0799 N 21 Thermal device and fan (Discrete graphics) v 2731-all v 2732-all v 2733-all v 2734-all v 2735-all v 2736-CTO v 2737-CTO 44C0800 N 22 Keyboard (see “Keyboard” on page 190.
LCD FRUs In R500, there are following types of LCDs. v 15.4-in. WXGA TFT LCD (Table 32 on page 180) v 15.4-in.
Table 32. Parts list—15.4-in. WXGA TFT No. FRU FRU no.
Table 32. Parts list—15.4-in. WXGA TFT (continued) No. FRU FRU no.
Table 32. Parts list—15.4-in. WXGA TFT (continued) No. FRU FRU no.
Table 32. Parts list—15.4-in. WXGA TFT (continued) No. FRU FRU no. CRU ID 8 LED control card v 2713-CTO v 2714-CTO v 2716-CTO v 2717-CTO v 2718-CTO v 2719-CTO v 2720-CTO v 2731-CTO v 2732-CTO v 2733-CTO v 2734-CTO v 2735-CTO v 2736-CTO v 2737-CTO 45M2780 N 9 42T0969 Bluetooth daughter card (BDC-2.
Table 32. Parts list—15.4-in. WXGA TFT (continued) No. 10 184 FRU FRU no. 42T0486 LCD panel, 15.4-in.
Table 32. Parts list—15.4-in. WXGA TFT (continued) No. 10 FRU FRU no. 42T0484 LCD panel, 15.4-in.
Table 32. Parts list—15.4-in. WXGA TFT (continued) No. 10 186 FRU FRU no. 42T0607 LCD panel, 15.4-in.
Table 32. Parts list—15.4-in. WXGA TFT (continued) No. FRU FRU no. CRU ID 10 42T0576 LCD panel, 15.4-in.
Table 33. Parts list—15.4-in. WSXGA+ TFT No. FRU FRU no.
Table 33. Parts list—15.4-in. WSXGA+ TFT (continued) No. FRU FRU no. CRU ID 9 Bluetooth daughter card (BDC-2.
Keyboard Table 34.
Table 35. Parts list—Keyboard Language P/N CRU ID Arabic 42T3212 42T3276 42T3146 Belgian 42T3213 42T3277 42T3147 Brazilian Portuguese 42T3240 42T3304 42T3174 Canadian French (058) 42T3211 42T3275 42T3145 Canadian French (Acnor) 42T3210 42T3274 42T3144 Czech 42T3214 42T3278 42T3148 Danish 42T3215 42T3279 42T3149 Dutch 42T3223 42T3287 42T3157 Finnish, Swedish 42T3230 42T3294 42T3164 French 42T3217 42T3281 42T3151 German 42T3218 42T3282 42T3152 Greek (U.S.
Miscellaneous parts Table 36. Parts list—Miscellaneous parts FRU P/N Screw kit (including nylon-coated screws): v M2 × 2.7 mm (black), flat head (5) v M2 × 2.8 mm (silver), flat head (10) v M2 × 3 mm (silver), flat head (30) v M2 × 3.5 mm (black), bind head (10) v M2 × 5 mm (black), flat head (15) v M2 × 9.5 mm (black), flat head (15) v M2 × 17mm (black), flat head (15) v M2 × 17mm (black), micro-bind head (2) v M2.5 × 4 mm (black), flat head (5) v M2.5 × 6.5 mm (black), flat head (10) v M2.5 × 6.
Table 36.
AC adapters Table 37. Parts list—2-pin AC adapters FRU FRU no.
Power cords A ThinkPad power cord for a specific country or region is usually available only in that country or region: Table 39. Parts list—2-pin power cords Country or region FRU no. CRU ID Argentina v models -CTO, xxY 42T5020 42T5105 * Brazil v models -CTO, xxP 42T5180 42T5183 Canada, U.S. v models -CTO, xxF, xxL, xxS, xxU 42T5008 42T5093 Japan v models -CTO, xxE, xxJ 42T5014 42T5099 Table 40. Parts list—3-pin power cords Country or region FRU no.
Recovery discs Windows XP Professional (32 bit) DVDs Windows XP Professional (32 bit) is preinstalled as the operating system in the following models: v 2713-CTO, 97x, 98x v 2714-CTO, 5Ux, 5Vx, 5Wx, 5Xx, 5Yx, 5Zx, 62x, 63x, 64x, 65x, 66x, 67x, 68x, 69x, 6Ax, 6Bx, 6Cx, 6Dx, 6Ex, 6Fx, 6Gx, 6Hx, 79x, 7Kx, 7Mx, 7Ux, 7Yx, 8Ux, 92x, 93x, 94x, 95x, 9Sx, 9Wx, A7x, AFx, AGx, AHx, AKx, ANx, AQx, ARx v 2716-CTO, 6Jx, 6Kx, 6Lx, 6Mx, 6Nx, 6Px, 6Qx, 6Rx, 6Sx, 6Tx, 7Gx, 7Hx, 8Cx, 8Nx, 9Ex, A5x, AUx, AWx, AXx, AZx, B3x v 2
Table 41.
Windows Vista Starter Edition (32 bit) recovery DVDs Windows Vista Starter Edition (32 bit) is preinstalled as the operating system in the following models: v 2713-CTO v 2714-CTO, 7Px, 7Qx v 2716-CTO v 2717-CTO v 2718-CTO v 2719-CTO v 2720-CTO v 2731-CTO v 2732-CTO v 2733-CTO v 2734-CTO v 2735-CTO v 2736-CTO v 2737-CTO Table 42.
Windows Vista Home Basic (32 bit) recovery DVDs Windows Vista Home Basic (32 bit) is preinstalled as the operating system in the following models: v 2713-CTO, 5Jx, 99x v 2714-CTO, 54x, 5Cx, E7x, E8x, 9Rx, 9Ux v 2716-CTO, 5Tx, 9Ax v 2717-CTO v 2718-CTO, 49x, 4Ax v 2719-CTO v 2720-CTO v 2731-CTO, 4Px, 4Qx, 4Rx, 4Sx, 77x v 2732-CTO, 3Wx, 3Xx, 3Yx, 4Gx, 4Hx v 2733-CTO, 3Cx v 2734-CTO v 2735-CTO v 2736-CTO v 2737-CTO Parts list 199
Table 43.
Windows Vista Home Premium (32 bit) recovery DVDs Windows Vista Home Premium (32 bit) is preinstalled as the operating system in the following models: v 2713-CTO v 2714-CTO, 39x, 3Bx, 3Cx, 4Wx, 4Xx, 4Yx, 4Zx, 53x, 9Nx, 9Px, 9Qx, 9Tx, E9x, EAx v 2716-CTO v 2717-CTO v 2718-CTO v 2719-CTO v 2720-CTO v 2731-CTO v 2732-CTO, 36x, 7Ex, 7Fx, 7Hx v 2733-CTO v 2734-CTO v 2735-CTO v 2736-CTO v 2737-CTO Table 44.
Windows Vista Business (32 bit) recovery DVDs Windows Vista Business (32 bit) is preinstalled as the operating system in the following models: v 2713-CTO, 3Fx, 3Gx, 3Hx, 3Jx, 5Kx, 5Lx, 5Mx, 7Ax, 7Bx, 9Dx v 2714-CTO, 34x, 36x, 37x, 3Ax, 3Dx, 3Ex, 4Lx, 4Mx, 4Px, 4Qx, 4Rx, 4Sx, 4Tx, 55x, 56x, 57x, 58x, 59x, 5Ax, 5Bx, 5Dx, 76x, 77x, 78x, 7Jx, 7Lx, 7Nx, 7Sx, 7Tx, 7Vx, 7Wx, 7Xx, 8Lx, 8Mx, 8Tx, 9Xx, E3x, E5x, E6x v 2716-CTO, 3Kx, 3Lx, 3Mx, 3Nx, 3Px, 3Qx, 3Rx, 3Sx, 3Vx, 3Wx, 3Xx, 3Zx, 42x, 43x, 44x, 5Nx, 5Px, 5Qx,
Table 45.
Windows Vista Business (64 bit) recovery DVDs Windows Vista Business (64 bit) is preinstalled as the operating system in the following models: v 2713-CTO v 2714-CTO v 2716-CTO v 2717-CTO v 2718-CTO v 2719-CTO v 2720-CTO v 2731-CTO v 2732-CTO v 2733-CTO v 2734-CTO v 2735-CTO v 2736-CTO v 2737-CTO Table 46.
Windows Vista Ultimate (32 bit) recovery DVDs Windows Vista Ultimate (32 bit) is preinstalled as the operating system in the following models: v 2713-CTO v 2714-CTO, 4Ux, 4Vx, 96x v 2716-CTO, 45x, 8Sx v 2717-CTO, 8Vx v 2718-CTO, 4Kx, 8Sx v 2719-CTO v 2720-CTO v 2731-CTO v 2732-CTO v 2733-CTO, 3Kx, 3Px, 3Qx v 2734-CTO v 2735-CTO, 3Ux, 3Vx v 2736-CTO v 2737-CTO Parts list 205
Table 47.
Windows 7 Home Basic (32 bit) DVDs Windows 7 Home Basic (32 bit) is preinstalled as the operating system in the following models: v 2713-CTO v 2714-CTO v 2716-CTO v 2717-CTO v 2718-CTO v 2719-CTO v 2720-CTO v 2731-CTO v 2732-CTO v 2733-CTO v 2734-CTO v 2735-CTO v 2736-CTO v 2737-CTO Table 48.
Windows 7 Home Premium (32 bit) DVDs Windows 7 Home Premium (32 bit) is preinstalled as the operating system in the following models: v 2713-CTO v 2714-CTO v 2716-CTO v 2717-CTO v 2718-CTO v 2719-CTO v 2720-CTO v 2731-CTO v 2732-CTO v 2733-CTO v 2734-CTO v 2735-CTO v 2736-CTO v 2737-CTO Table 49.
Windows 7 Home Premium (64 bit) DVDs Windows 7 Home Premium (64 bit) is preinstalled as the operating system in the following models: v 2713-CTO v 2714-CTO v 2716-CTO v 2717-CTO v 2718-CTO v 2719-CTO v 2720-CTO v 2731-CTO v 2732-CTO v 2733-CTO v 2734-CTO v 2735-CTO v 2736-CTO v 2737-CTO Table 50.
Windows Professional (32 bit) DVDs Windows Professional (32 bit) is preinstalled as the operating system in the following models: v 2713-CTO v 2714-CTO, AAx, AJx, ALx, AMx, APx, B5x, B6x, B7x, B8x v 2716-CTO, ADx, AEx, AVx, AYx, B2x, B4x v 2717-CTO, ACx v 2718-CTO v 2719-CTO v 2720-CTO v 2731-CTO v 2732-CTO, 7Ux, 83x, 84x v 2733-CTO, 7Wx, 7Xx, 82x v 2734-CTO, 7Vx v 2735-CTO v 2736-CTO v 2737-CTO 210 ThinkPad R500 Hardware Maintenance Manual
Table 51.
Windows Professional (64 bit) DVDs Windows Professional (64 bit) is preinstalled as the operating system in the following models: v 2713-CTO v 2714-CTO v 2716-CTO v 2717-CTO v 2718-CTO v 2719-CTO v 2720-CTO v 2731-CTO v 2732-CTO v 2733-CTO v 2734-CTO v 2735-CTO v 2736-CTO v 2737-CTO Table 52.
Common service tools Table 53. Parts list—Common service tools Tool P/N Screwdriver kit 95F3598 1/4″ drive spinner handle 1650840 1/4″ Sq. to 1/4″ hex torx adapter 93F2838 TR7-TR-10 tamper resistant torx bits 00P6967 Removal tool antenna RF connector 08K7159 USB 2.
214 ThinkPad R500 Hardware Maintenance Manual
Notices Lenovo may not offer the products, services, or features discussed in this document in all countries. Consult your local Lenovo representative for information on the products and services currently available in your area. Any reference to a Lenovo product, program, or service is not intended to state or imply that only that Lenovo product, program, or service may be used.
vary significantly. Some measurements may have been made on development-level systems and there is no guarantee that these measurements will be the same on generally available systems. Furthermore, some measurements may have been estimated through extrapolation. Actual results may vary. Users of this document should verify the applicable data for their specific environment.
Part Number: 43Y6631_03 (1P) P/N: 43Y6631_03 *1P43Y6631_03*
