® ThinkPad X301 Hardware Maintenance Manual
® ThinkPad X301 Hardware Maintenance Manual
Note Before using this information and the product it supports, be sure to read the general information under “Notices” on page 135. Second Edition (October 2008) © Copyright Lenovo 2008. All rights reserved. LENOVO products, data, computer software, and services have been developed exclusively at private expense and are sold to governmental entities as commercial items as defined by 48 C.F.R. 2.101 with limited and restricted rights to use, reproduction and disclosure.
Contents About this manual . . . . . . . . . . v Safety information . . . . . . . . . . 1 General safety . . . . . . . . . . . . . . 2 Electrical safety . . . . . . . . . . . . . 3 Safety inspection guide . . . . . . . . . . . 5 Handling devices that are sensitive to electrostatic discharge . . . . . . . . . . . . . . . 6 Grounding requirements . . . . . . . . . . 6 Safety notices: multilingual translations . . . . . 7 Laser compliance statement . . . . . . . . . 14 Important service information . . . . .
Common service tools . . . . . . . . . 134 Notices . . . . . . . . . . . . . . 135 iv ThinkPad X301 Hardware Maintenance Manual Trademarks . . . . . . . . . . . . . .
About this manual This manual contains service and reference information for the following ThinkPad® products. ThinkPad X301 MT 2774, 2776, 2777, 2778, 2779, 4057, and 4182 Use this manual along with the advanced diagnostic tests to troubleshoot problems. The manual is divided into sections as follows: v The common sections provide general information, guidelines, and safety information required in servicing computers.
vi ThinkPad X301 Hardware Maintenance Manual
Safety information This chapter presents following safety information that you need to be familiar with before you service a ThinkPad computer.
General safety Follow these rules to ensure general safety: v Observe good housekeeping in the area of the machines during and after maintenance. v When lifting any heavy object: 1. Make sure that you can stand safely without slipping. 2. Distribute the weight of the object equally between your feet. 3. Use a slow lifting force. Never move suddenly or twist when you attempt to lift. 4. Lift by standing or by pushing up with your leg muscles; this action removes the strain from the muscles in your back.
Electrical safety Observe the following rules when working on electrical equipment. Important: Use only approved tools and test equipment. Some hand tools have handles covered with a soft material that does not insulate you when working with live electrical currents. Many customers have, near their equipment, rubber floor mats that contain small conductive fibers to decrease electrostatic discharges. Do not use this type of mat to protect yourself from electrical shock.
v Do not touch live electrical circuits with the reflective surface of a plastic dental mirror. The surface is conductive; such touching can cause personal injury and machine damage. v Do not service the following parts with the power on when they are removed from their normal operating places in a machine: – Power supply units – Pumps – Blowers and fans – Motor generators and similar units. (This practice ensures correct grounding of the units.
Safety inspection guide The purpose of this inspection guide is to assist you in identifying potentially unsafe conditions. As each machine was designed and built, required safety items were installed to protect users and service personnel from injury. This guide addresses only those items. You should use good judgment to identify potential safety hazards due to attachment of non-ThinkPad features or options not covered by this inspection guide.
Handling devices that are sensitive to electrostatic discharge Any computer part containing transistors or integrated circuits (ICs) should be considered sensitive to electrostatic discharge (ESD.) ESD damage can occur when there is a difference in charge between objects. Protect against ESD damage by equalizing the charge so that the machine, the part, the work mat, and the person handling the part are all at the same charge. Notes: 1.
Safety notices: multilingual translations The safety notices in this section are provided in English, French, German, Hebrew, Italian, Japanese, and Spanish. Safety notice 1 Before the computer is powered on after FRU replacement, make sure all screws, springs, and other small parts are in place and are not left loose inside the computer. Verify this by shaking the computer and listening for rattling sounds. Metallic parts or metal flakes can cause electrical shorts.
Safety notice 2 DANGER Some standby batteries contain a small amount of nickel and cadmium. Do not disassemble a standby battery, recharge it, throw it into fire or water, or short-circuit it. Dispose of the battery as required by local ordinances or regulations. Use only the battery in the appropriate parts listing. Use of an incorrect battery can result in ignition or explosion of the battery. Certaines batteries de secours contiennent du nickel et du cadmium.
Safety notice 3 DANGER The battery pack contains small amounts of nickel. Do not disassemble it, throw it into fire or water, or short-circuit it. Dispose of the battery pack as required by local ordinances or regulations. Use only the battery in the appropriate parts listing when replacing the battery pack. Use of an incorrect battery can result in ignition or explosion of the battery. La batterie contient du nickel. Ne la démontez pas, ne l’exposez ni au feu ni à l’eau. Ne la mettez pas en court-circuit.
Safety notice 4 DANGER The lithium battery can cause a fire, an explosion, or a severe burn. Do not recharge it, remove its polarized connector, disassemble it, heat it above 100°C (212°F), incinerate it, or expose its cell contents to water. Dispose of the battery as required by local ordinances or regulations. Use only the battery in the appropriate parts listing. Use of an incorrect battery can result in ignition or explosion of the battery. La pile de sauvegarde contient du lithium.
Safety notice 5 If the LCD breaks and the fluid from inside the LCD gets into your eyes or on your hands, immediately wash the affected areas with water for at least 15 minutes. Seek medical care if any symptoms from the fluid are present after washing. Si le panneau d’affichage à cristaux liquides se brise et que vous recevez dans les yeux ou sur les mains une partie du fluide, rincez-les abondamment pendant au moins quinze minutes. Consultez un médecin si des symptômes persistent après le lavage.
Safety notice 6 DANGER To avoid shock, do not remove the plastic cover that protects the lower part of the inverter card. Afin d’éviter tout risque de choc électrique, ne retirez pas le cache en plastique protégeant la partie inférieure de la carte d’alimentation. Aus Sicherheitsgründen die Kunststoffabdeckung, die den unteren Teil der Spannungswandlerplatine umgibt, nicht entfernen.
Safety notice 8 DANGER Before removing any FRU, power off the computer, unplug all power cords from electrical outlets, remove the battery pack, and then disconnect any interconnecting cables. Avant de retirer une unité remplaçable en clientèle, mettez le système hors tension, débranchez tous les cordons d’alimentation des socles de prise de courant, retirez la batterie et déconnectez tous les cordons d’interface.
Laser compliance statement Some models of ThinkPad computer are equipped from the factory with an optical storage device such as a CD-ROM drive or a DVD-ROM drive. Such devices are also sold separately as options. If one of these drives is installed, it is certified in the U.S. to conform to the requirements of the Department of Health and Human Services 21 Code of Federal Regulations (DHHS 21 CFR) Subchapter J for Class 1 laser products.
A CD-ROM drive, a DVD-ROM drive, or any other storage device installed may contain an embedded Class 3A or Class 3B laser diode. Note the following: DANGER Emits visible and invisible laser radiation when open. Do not stare into the beam, do not view directly with optical instruments, and avoid direct exposure to the beam. Radiação por raio laser ao abrir. Não olhe fixo no feixe de luz, não olhe diretamente por meio de instrumentos óticos e evite exposição direta com o feixe de luz.
16 ThinkPad X301 Hardware Maintenance Manual
Important service information This chapter presents following important service information: v “Strategy for replacing FRUs” – “Strategy for replacing a hard disk drive” on page 18 – “Important notice for replacing a system board” on page 18 – “How to use error message” on page 18 v “Strategy for replacing FRUs for CTO, CMV, and GAV” on page 19 – “Product definition” on page 19 – “FRU identification for CTO, CMV, and GAV products” on page 19 v “Important information about replacing RoHS compliant FRUs” on p
v If you are instructed to replace a FRU but the replacement does not correct the problem, reinstall the original FRU before you continue. v Some computers have both a processor board and a system board. If you are instructed to replace either the processor board or the system board, and replacing one of them does not correct the problem, reinstall that board, and then replace the other one. v If an adapter or a device consists of more than one FRU, any of the FRUs may be the cause of the error.
Strategy for replacing FRUs for CTO, CMV, and GAV Product definition Dynamic Configure To Order (CTO) This provides the ability for a customer to configure an IBM® or a Lenovo solution from an eSite, and have this configuration sent to fulfillment, where it is built and shipped directly to the customer. The machine label, Product Entitlement Warehouse (PEW), eSupport, and the HMM will load these products as the 4-digit MT and 3-digit model, where model = “CTO” (Example: 1829-CTO).
warranty.vm&sitestyle=lenovo Select Warranty lookup. Input the MT and the Serial number and the list of key commodities will be returned in the PEW record under COMPONENT INFORMATION. v Business Partners using Eclaim will access PEW when performing Entitlement Lookup. Business Partners will enter Loc ID, MT and Serial, and the key commodities will be returned in the Eclaim record under SYSTEM DETAILS. v Authorized IBM Business Partners can access Eclaim at the following Web site: https://wca.eclaim.
Important information about replacing RoHS compliant FRUs RoHS, The Restriction of Hazardous Substances in Electrical and Electronic Equipment Directive (2002/95/EC) is a European Union legal requirement affecting the global electronics industry. RoHS requirements must be implemented on Lenovo products placed on the market after June 2006. Products on the market before June 2006 are not required to have RoHS compliant parts.
22 ThinkPad X301 Hardware Maintenance Manual
General checkout This chapter presents following information: v “What to do first” on page 24 v “Checkout guide” on page 25 – “Diagnostics using PC-Doctor for DOS” on page 26 – “PC-Doctor for Windows” on page 28 – “PC-Doctor for Rescue and Recovery” on page 28 v “Power system checkout” on page 29 The descriptions in this chapter apply to any ThinkPad model that supports the PC-Doctor® for DOS diagnostics program. Some descriptions might not apply to your particular computer.
What to do first When you do return a FRU, you must include the following information in the parts exchange form or parts return form that you attach to it: __ 1. Name and phone number of servicer __ 2. Date of service __ 3. Date on which the machine failed __ 4. Date of purchase __ 5. Failure symptoms, error codes appearing on the display, and beep symptoms __ 6. Procedure index and page number in which the failing FRU was detected __ 7. Failing FRU name and part number __ 8.
Checkout guide Use the following procedures as a guide in identifying and correcting problems with the ThinkPad computer. Note: The diagnostic tests are intended to test only ThinkPad products. The use of non-ThinkPad products, prototype cards, or modified options can lead to false indications of errors and invalid system responses. 1. Identify the failing symptoms in as much detail as possible. 2. Verify the symptoms.
Diagnostics using PC-Doctor for DOS The ThinkPad computer has a test program called PC-Doctor for DOS (hereafter called PC-Doctor.) You can detect errors by running the diagnostics test included in PC-Doctor. This section is an overview of the procedure. For details that depend on model-unique functions, refer to “ThinkPad X301” on page 47. Note: PC-Doctor for DOS is available at following Web site: http://www.lenovo.
Note: PC-Doctor menu does not mean the formal support device list. Some unsupported device names may appear in the PC-Doctor menu. Diagnostics Interactive Tests Hardware Info Utility Quit F1=Help Run Normal Test Run Quick Test CPU/Coprocessor Systemboard Video Adapter Serial Ports Fixed Disks Diskette Drives Other Devices Communication Wireless LAN PM Memory PC-DOCTOR 2.0 Copyright 2002 PC-Doctor, Inc. All Rights Reserved. Use the cursor keys and ESC to move in menus. Press ENTER to select.
Detecting system information with PC-Doctor PC-Doctor can detect the following system information: Hardware Info v System Configuration v Memory Contents v Physical Disk Drives v Logical Disk Drives v VGA Information v IDE Drive Info v PCI Information v PNPISA Info v SMBIOS Info v VESA LCD Info v Hardware Events Log Utility v v v v v v v v v v v Run External Tests Surface Scan Hard Disk Benchmark System DOS Shell Tech Support Form Battery Rundown View Test Log Print Log Save Log Full Erase Hard Drive Quick
Power system checkout To 1. 2. 3. 4. 5. 6. 7. verify a symptom, do the following: Turn off the computer. Remove the battery pack. Connect the ac adapter. Check that power is supplied when you turn on the computer. Turn off the computer. Disconnect the ac adapter and install the charged battery pack. Check that the battery pack supplies power when you turn on the computer.
Checking operational charging To check whether the battery charges properly during operation, use a discharged battery pack or a battery pack that has less than 50% of the total power remaining when installed in the computer. Perform operational charging. If the battery status indicator or icon does not turn on, remove the battery pack and let it return to room temperature. Reinstall the battery pack. If the charge indicator or icon still does not turn on, replace the battery pack.
Checking the backup battery Do the following: 1. Power off the computer, and unplug the ac adapter from it. 2. Turn the computer upside down. 3. Remove the battery pack (see “1010 Battery pack” on page 61). 4. Remove the backup battery (see “1080 Backup battery” on page 77). 5. Measure the voltage of the backup battery. See the following figure. Red (+) Black (-) Wire Voltage (V dc) Red +2.5 to +3.2 Black Ground v If the voltage is correct, replace the system board.
32 ThinkPad X301 Hardware Maintenance Manual
Related service information This chapter presents following information: v “Restoring the factory contents by using Product Recovery discs” v “Passwords” on page 34 v “Power management” on page 37 v “Symptom-to-FRU index” on page 39 Service Web site: When the latest maintenance diskette and the system program service diskette become available, they will be posted on http://www.lenovo.
8. When the recovery process is complete, the Welcome to Microsoft Windows screen is displayed. Follow the instructions on the screen to complete the Windows setup. Passwords As many as three passwords may be needed for any ThinkPad computer: the power-on password (POP), the hard-disk password (HDP), and the supervisor password (SVP). If any of these passwords has been set, a prompt for it appears on the screen whenever the computer is turned on. The computer does not start until the password is entered.
How to remove the power-on password To remove a POP that you have forgotten, do the following: (A) If no SVP has been set: 1. Turn off the computer. 2. Remove the battery pack. For how to remove the battery pack, see “1010 Battery pack” on page 61. 3. Remove the backup battery. For how to remove the backup battery, see “1080 Backup battery” on page 77. 4. Turn on the computer and wait until the POST ends. After the POST ends, the password prompt does not appear. The POP has been removed. 5.
3. 4. 5. 6. 7. 8. 9. 36 Note: To check whether the ThinkPad computer supports the Passphrase function, enter the BIOS Setup Utility and go to Security --> Password. If Using Passphrase item is displayed in the menu, this function is available on the ThinkPad computer. Select Security, using the cursor directional keys to move down the menu. Select Password. Select Hard-disk x password, where x is the letter of the hard disk drive. A pop-up window opens. Select Master HDP.
Power management To reduce power consumption, the computer has three power management modes: screen blank, standby, and hibernation. Screen blank mode If the time set on the “Turn off monitor” timer in the operating system expires, the LCD backlight turns off. To put the computer into screen blank mode, press the ThinkVantage® button and use the ThinkVantage Productivity Center. To end screen blank mode and resume normal operation, press any key.
v The ring indicator (RI) is signaled by a serial device or a PC Card device. v The time set on the resume timer elapses. Note: The computer does not accept any input immediately after it enters standby mode. Wait a few seconds before taking any action to reenter operation mode. Hibernation mode In hibernation mode, the following occurs: v The system status, RAM, VRAM, and setup data are stored on the hard disk. v The system is powered off.
Symptom-to-FRU index This section contains following information: v “Numeric error codes” v “Error messages” on page 43 v “Beep symptoms” on page 44 v “No-beep symptoms” on page 44 v “LCD-related symptoms” on page 45 v “Intermittent problems” on page 46 v “Undetermined problems” on page 46 The symptom-to-FRU index in this section lists symptoms and errors and their possible causes. The most likely cause is listed first, in boldface type.
Table 1. Numeric error codes (continued) Symptom or error FRU or action, in sequence 0187 EAIA data access error—The access to EEPROM is failed. System board. 0188 Invalid RFID Serialization Information Area. System board. 0189 System board. Invalid RFID configuration information area—The EEPROM checksum is not correct. 40 0190 Critical low-battery error 1. Charge the battery pack. 2. Battery pack. 0191 System Security—Invalid Remote Change requested. 1.
Table 1. Numeric error codes (continued) Symptom or error FRU or action, in sequence 0251 System CMOS checksum bad— Default configuration used. 1. Charge the backup battery for more than 8 hours by connecting the ac adapter. 2. Replace the backup battery and run BIOS Setup Utility to reset the time and date. 0252 Password checksum bad—The password is cleared. Reset the password by running BIOS Setup Utility. 0260 System timer error. 1.
Table 1. Numeric error codes (continued) Symptom or error FRU or action, in sequence 1805 Unauthorized Wireless USB card is plugged in—Power off and remove the Wireless USB card. 1. Remove the Wireless USB card that you installed. 2. System board. 1820 More than one external fingerprint reader is attached. Power off and remove all but the reader that you set up within your main operating system. Remove all but the reader that you set up for the authentication.
Error messages Table 2. Error messages Symptom or error FRU or action, in sequence Device address conflict. 1. Load “Setup Defaults” in the BIOS Setup Utility. 2. Backup battery. 3. System board. Allocation error for device. 1. Load “Setup Defaults” in the BIOS Setup Utility. 2. Backup battery. 3. System board. Failing bits: nnnn. 1. DIMM. 2. System board. Invalid system configuration data. 1. DIMM. 2. System board. I/O device IRQ conflict. 1. Load “Setup Defaults” in the BIOS Setup Utility. 2.
Beep symptoms Table 3. Beep symptoms Symptom or error FRU or action, in sequence One beep and a blank, unreadable, or flashing LCD. 1. 2. 3. 4. One long and two short beeps, and a blank or unreadable LCD. 1. System board. 2. LCD assembly. 3. DIMM. Two short beeps with error codes. POST error. See “Numeric error codes” on page 39. Two short beeps and a blank screen. 1. System board. 2. DIMM. Three short beeps, pause, three more short beeps, and one short beep. 1. DIMM. 2.
LCD-related symptoms Important: The TFT LCD for the notebook computer contains many thin-film transistors (TFTs). The presence of a small number of dots that are missing, discolored, or always lighted is characteristic of TFT LCD technology, but excessive pixel problems can cause viewing concerns. The LCD should be replaced if the number of missing, discolored, or lighted dots in any background is as follows: Table 5.
Intermittent problems Intermittent system hang problems can be due to a variety of causes that have nothing to do with a hardware defect, such as cosmic radiation, electrostatic discharge, or software errors. FRU replacement should be considered only when a problem recurs. When analyzing an intermittent problem, do the following: 1. Run the diagnostic test for the system board in loop mode at least 10 times. 2. If no error is detected, do not replace any FRUs. 3.
ThinkPad X301 This chapter presents following product-specific service references and product-specific parts information. v “Specifications” v “Status indicators” on page 49 v “FRU tests” on page 51 v “Fn key combinations” on page 53 v “FRU replacement notices” on page 55 v “Removing and replacing a FRU” on page 59 v “Locations” on page 113 v “Parts list” on page 115 Specifications The following table lists the specifications of the ThinkPad X301 : Table 7.
Table 7. Specifications (continued) 48 Feature Description I/O port v v v v v v Audio v Built-in stereo speakers v Software control volume Ethernet (on the system board) v Gigabit Ethernet PCI Express Mini Card v v v v v v v Bluetooth wireless v ThinkPad Bluetooth with Enhanced Data Rate (BDC-2.1) Touch pad v UltraNav® ThinkLight® Yes Battery v Li-Polymer battery (3 cells) 2.44 Ah v Li-ion second battery (6 cells) 4.
Status indicators The system status indicators show the status of the computer, as follows: 10 9 8 7 6 5 2 4 3 3 2 1 4 ThinkPad X301 49
Table 8. Status indicators 50 Indicator Meaning 1 Power on Green: The computer is on and ready to use. This indicator stays lit whenever the computer is on and is not in standby mode. 2 Standby status Green: The computer is in standby mode. Blinking green: The computer is entering standby mode or hibernation mode, or is resuming normal operation. 3 AC power status Green: The computer is connected to the ac power supply.
FRU tests The following table shows the test for each FRU. Table 9. FRU tests FRU Applicable test System board 1. Diagnostics --> CPU/Coprocessor 2. Diagnostics --> Systemboard 3. Place the computer on a horizontal surface, and run Diagnostics --> ThinkPad Devices --> HDD Active Protection Test. Note: Do not apply any physical shock to the computer while the test is running. Power Diagnostics --> ThinkPad Devices --> AC Adapter, Battery 1 (Battery2) LCD unit 1. Diagnostics --> Video Adapter 2.
Table 9. FRU tests (continued) FRU Applicable test Fan 1. Turn on the computer and check the air turbulence at the louver near the PC Card slot. 2. Run Diagnostics --> ThinkPad Devices --> Fan. TrackPoint or pointing If the TrackPoint does not work, check the configuration as device specified in the BIOS Setup Utility. If the TrackPoint is disabled, select Automatic to enable it. After you use the TrackPoint, the pointer may drift on the screen for a short time.
Fn key combinations The following table shows the function of each combination of Fn with a function key. Table 10. Fn key combinations Key combination Description Fn+F1 Reserved. Fn+F2 Lock your computer. Fn+F3 Select a power scheme that has been created by Power Manager. When you press this combination, a panel for selecting a power scheme appears. Notes: 1. To use the Fn+F3 key combination, you must have the ThinkPad PM device driver installed on the computer. 2.
Table 10. Fn key combinations (continued) Key combination Description Fn+F7 Apply a presentation scheme directly, with no need to start Presentation Director. To disable this function and use the Fn+F7 key combination for switching a display output location, start Presentation Director, and change the settings. Switch a display output location v External monitor (CRT display) v Computer display and external monitor (LCD + CRT display) v Computer display (LCD) Notes: 1.
FRU replacement notices This section contains notices related to removing and replacing parts. Read this section carefully before replacing any FRU. Screw notices Loose screws can cause a reliability problem. In the ThinkPad computer, this problem is addressed with special nylon-coated screws that have the following characteristics: v They maintain tight connections. v They do not easily come loose, even with shock or vibration. v They are harder to tighten. v Each one should be used only once.
Retaining serial numbers This section includes the following descriptions: v “Restoring the serial number of the system unit” v “Retaining the UUID” v “Reading or writing the ECA information” on page 58 Restoring the serial number of the system unit When the computer was manufactured, the EEPROM on the system board was loaded with the serial numbers of the system and all major components. These numbers need to remain the same throughout the life of the computer.
When you replace the system board, you must set the UUID on the new system board as follows: 1. Install the ThinkPad Hardware Maintenance Diskette Version 1.73 or later, and restart the computer. 2. From the main menu, select 4. Assign UUID. A new UUID is created and written. If a valid UUID already exists, it is not overwritten.
Reading or writing the ECA information Information on Engineering Change Announcements (ECA) are stored in the EEPROM of the system board. The electronic storage of this information simplifies the procedure to check if the ECA has been previously applied to a machine. The machine does not need to be disassembled to check for the ECA application. To check what ECAs have been previously applied to the machine, use the ECA Information Read/Write function on the ThinkPad Hardware Maintenance Diskette Version 1.
Removing and replacing a FRU This section presents directions and drawings for use in removing and replacing a FRU. Be sure to observe the following general rules: 1. Do not try to service any computer unless you have been trained and certified. An untrained person runs the risk of damaging parts. 2. Before replacing any FRU, review “FRU replacement notices” on page 55. 3. Begin by removing any FRUs that have to be removed before the failing FRU. Any such FRUs are listed at the top of the page.
Before servicing ThinkPad X301 Removing the SIM card: Some models of the ThinkPad X301 you are servicing might have the SIM card that the customer has been installed. If the computer you are servicing has the SIM card, remove it before you start the servicing. To remove the SIM card, you need to remove the battery pack first. (See “1010 Battery pack” on page 61.) After you finish the servicing, make sure that you insert the card back into the slot firmly.
1010 Battery pack Table 11. Removal steps of battery pack Unlock the battery latch 1 . Holding the battery lock lever in the unlocked position 2 , remove the battery pack in the direction shown by arrow 3 and 4 . Note: Large battery used in some models only has one battery latch. 2 1 3 4 When installing: Install the battery pack along the slide rails of the slot. Then make sure that the battery release lever is in the locked position.
1020 Optical drive or second battery or travel cover For access, remove this FRU: v “1010 Battery pack” on page 61 Table 12. Removal steps of optical drive or second battery or travel cover Note: For models with the travel cover, skip step 1 . 1 Step Screw (quantity) Color Torque 1 M2 × 6 mm, bind-head, nylon-coated (1) Black 0.167 Nm (1.
1030 Solid state drive (SSD) or hard disk drive (HDD) For access, remove these FRUs in order: v “1010 Battery pack” on page 61 v “1020 Optical drive or second battery or travel cover” on page 62 Attention: v Do not drop the drive or apply any physical shock to it. The drive is sensitive to physical shock. Improper handling can cause damage and permanent loss of data. v Before removing the drive, have the user make a backup copy of all the information on it if possible.
Table 13. Removal steps of SSD or HDD (continued) 3 When installing: Make sure that the SSD connector or HDD connector is attached firmly.
1040 DIMM For access, remove these FRUs in order: v “1010 Battery pack” on page 61 v “1020 Optical drive or second battery or travel cover” on page 62 Table 14. Removal steps of DIMM Note: Loosen the screws 1 , but do not remove them.
Table 14. Removal steps of DIMM (continued) Note: If only one DIMM is used on the computer you are servicing, the card must be installed in SLOT-0 ( a ), but not in SLOT-1 ( b ). b a 3 4 3 When installing: Insert the notched end of the DIMM into the socket. Press the DIMM firmly, and pivot it until it snaps into the place. Make sure that it is firmly fixed in the slot and does not move easily.
1050 PCI Express Mini Card for wireless LAN For access, remove these FRUs in order: v “1010 Battery pack” on page 61 v “1020 Optical drive or second battery or travel cover” on page 62 Table 15. Removal steps of PCI Express Mini Card for wireless LAN Note: Loosen the screws 1 , but do not remove them.
Table 15. Removal steps of PCI Express Mini Card for wireless LAN (continued) In step 3 , unplug the jacks by using the removal tool antenna RF connector (P/N: 08K7159) or pick the connectors with your fingers and gently unplug them in direction of the arrow. Note: Some models might have only two antenna cables in step 3 . 4 4 3 68 Step Screw (quantity) Color Torque 4 M2 × 3 mm, small-head, nylon-coated (2) Silver 0.167 Nm (1.
Table 15. Removal steps of PCI Express Mini Card for wireless LAN (continued) 5 When installing: v In models with wireless LAN card that has two antenna connectors, plug the gray cable into the jack labeled MAIN, and the black cable into the jack labeled AUX on the card. If the computer you are servicing has three cables, put the white cable in the cable holder.
1060 Wireless USB adapter or Intel Turbo Memory For access, remove these FRUs in order: v “1010 Battery pack” on page 61 v “1020 Optical drive or second battery or travel cover” on page 62 Table 16. Removal steps of wireless USB adapter or Intel Turbo Memory Note: Loosen the screws 1 , but do not remove them.
Table 16. Removal steps of wireless USB adapter or Intel Turbo Memory (continued) In step 3 , unplug the jacks by using the removal tool antenna RF connector (P/N: 08K7159) or pick the connectors with your fingers and gently unplug them in direction of the arrow. Note: Step 3 is only for the models with Wireless USB adapter. For the models with Intel Turbo Memory, skip step 3 . 4 4 3 Step Screw (quantity) 4 For Japan M2 × 3 mm, tamper proof (2) Color Torque Black 0.189 Nm (1.
Table 16.
1070 Keyboard For access, remove these FRUs in order: v “1010 Battery pack” on page 61 v “1020 Optical drive or second battery or travel cover” on page 62 Table 17. Removal steps of keyboard Attention: If a travel cover is installed on the computer you are servicing, you need to remove it before removing the screw that secures the keyboard. In models with the travel cover, screw 1a should have been removed when you removed the travel cover.
Table 17. Removal steps of keyboard (continued) 3 2 3 3 Lift the keyboard a little in the direction shown by arrow 4 , and then detach the connector 5 .
When installing the keyboard, do as follows: Table 18. Installation of the keyboard 1. Attach the keyboard connector. 2. Attach the keyboard so that the keyboard edges a are under the frame as shown in this figure.
Table 18. Installation of the keyboard (continued) 3. To make sure that the front side of the keyboard is housed firmly, gently press the keys with your thumbs and try to slide the keyboard toward you. 4. Secure the keyboard by tightening the screws from the bottom side of the computer.
1080 Backup battery DANGER Use only the battery specified in the parts list for your computer. Any other battery could ignite or explode. For access, remove these FRUs in order: v “1010 Battery pack” on page 61 v “1020 Optical drive or second battery or travel cover” on page 62 v “1070 Keyboard” on page 73 Table 19. Removal steps of backup battery 1 2 When installing: Make sure that the battery connector is attached firmly.
1090 PCI Express Mini Card for wireless WAN For access, remove these FRUs in order: v “1010 Battery pack” on page 61 v “1020 Optical drive or second battery or travel cover” on page 62 v “1070 Keyboard” on page 73 Table 20. Removal steps of PCI Express Mini Card for wireless WAN In step 1 , unplug the jacks by using the removal tool antenna RF connector (P/N: 08K7159) or pick the connectors with your fingers and gently unplug them in direction of the arrow.
Table 20. Removal steps of PCI Express Mini Card for wireless WAN (continued) 3 Note: Plug the red cable into the jack labeled MAIN on the card, and the blue cable into the jack labeled AUX.
1100 Palm rest or palm rest with fingerprint reader For access, remove these FRUs in order: v “1010 Battery pack” on page 61 v “1020 Optical drive or second battery or travel cover” on page 62 v “1030 Solid state drive (SSD) or hard disk drive (HDD)” on page 63 v “1070 Keyboard” on page 73 Note: In models with the fingerprint reader, the sensor is attached to the palm rest FRU.
Table 21.
1110 Bluetooth daughter card (BDC-2) For access, remove these FRUs in order: v “1010 Battery pack” on page 61 v “1020 Optical drive or second battery or travel cover” on page 62 v “1070 Keyboard” on page 73 v “1100 Palm rest or palm rest with fingerprint reader” on page 80 Table 22. Removal steps of BDC-2 1 2 Step Screw (quantity) Color Torque 1 M2 × 6 mm, bind-head, nylon-coated (1) Black 0.167 Nm (1.7 kgfcm) When installing: Make sure that connector is attached firmly.
1120 Keyboard bezel For access, remove these FRUs in order: v “1010 Battery pack” on page 61 v “1020 Optical drive or second battery or travel cover” on page 62 v “1050 PCI Express Mini Card for wireless LAN” on page 67 v “1060 Wireless USB adapter or Intel Turbo Memory” on page 70 v “1070 Keyboard” on page 73 v “1090 PCI Express Mini Card for wireless WAN” on page 78 v “1100 Palm rest or palm rest with fingerprint reader” on page 80 Table 23.
Table 23. Removal steps of keyboard bezel (continued) 2 3 2 Step Screw (quantity) Color Torque 2 M2 × 6 mm, bind-head, nylon-coated (2) Black 0.167 Nm (1.7 kgfcm) 3 M2 × 4 mm, bind-head, nylon-coated (1) Black 0.167 Nm (1.
Table 23. Removal steps of keyboard bezel (continued) 6 Note: Before step 8 , pull the cables out from the cable guide hole of the keyboard bezel as shown in a in this figure.
1130 Audio FPC and audio sub card For access, remove these FRUs in order: v “1010 Battery pack” on page 61 v “1020 Optical drive or second battery or travel cover” on page 62 v “1050 PCI Express Mini Card for wireless LAN” on page 67 v “1060 Wireless USB adapter or Intel Turbo Memory” on page 70 v “1070 Keyboard” on page 73 v “1090 PCI Express Mini Card for wireless WAN” on page 78 v “1100 Palm rest or palm rest with fingerprint reader” on page 80 v “1120 Keyboard bezel” on page 83 Table 24.
Table 24. Removal steps of audio FPC and audio sub card (continued) 6 6 7 5 Step Screw (quantity) Color Torque 6 M2 × 4 mm, bind-head, nylon-coated (2) Black 0.167 Nm (1.7 kgfcm) When installing: Make sure that the connector is attached firmly.
1140 Speaker assembly For access, remove these FRUs in order: v “1010 Battery pack” on page 61 v “1020 Optical drive or second battery or travel cover” on page 62 v “1050 PCI Express Mini Card for wireless LAN” on page 67 v “1060 Wireless USB adapter or Intel Turbo Memory” on page 70 v “1070 Keyboard” on page 73 v “1090 PCI Express Mini Card for wireless WAN” on page 78 v “1100 Palm rest or palm rest with fingerprint reader” on page 80 v “1120 Keyboard bezel” on page 83 v “1130 Audio FPC and audio sub card”
1150 LCD assembly For access, remove these FRUs in order: v “1010 Battery pack” on page 61 v “1020 Optical drive or second battery or travel cover” on page 62 v “1050 PCI Express Mini Card for wireless LAN” on page 67 v “1060 Wireless USB adapter or Intel Turbo Memory” on page 70 v “1070 Keyboard” on page 73 v “1090 PCI Express Mini Card for wireless WAN” on page 78 v “1100 Palm rest or palm rest with fingerprint reader” on page 80 v “1120 Keyboard bezel” on page 83 Table 26.
Table 26. Removal steps of LCD assembly (continued) 3 4 5 5 Step Screw (quantity) Color Torque 4 M2 × 3 mm, small-head, nylon-coated (1) Silver 0.167 Nm (1.
Table 26. Removal steps of LCD assembly (continued) When installing: 1. When you route the cables, make sure that they are not subjected to any tension. Tension could cause the cables to be damaged by the cable guides, or a wire to be broken. 2. Make sure that the LCD connector is attached firmly.
1160 VGA cable and DC-in connector For access, remove these FRUs in order: v “1010 Battery pack” on page 61 v “1020 Optical drive or second battery or travel cover” on page 62 v “1050 PCI Express Mini Card for wireless LAN” on page 67 v “1060 Wireless USB adapter or Intel Turbo Memory” on page 70 v “1070 Keyboard” on page 73 v “1090 PCI Express Mini Card for wireless WAN” on page 78 v “1100 Palm rest or palm rest with fingerprint reader” on page 80 v “1120 Keyboard bezel” on page 83 v “1150 LCD assembly” on
Table 27. Removal steps of VGA cable and DC-in connector (continued) In step 6 , detach the DC-in connector from the I/O bracket ( a ), then detach the VGA cable from the bracket 7 .
1170 System board, fan, and base cover assembly Important notices for handling the system board: When handling the system board, bear the following in mind. v The system board has an accelerometer, which can be broken by applying several thousands of G-forces. Note: Dropping a system board from a height of as little as 6 inches so that it falls flat on a hard bench can subject the accelerometer to as much as 6,000 G’s of shock.
Following components soldered on the top side of the system board are extremely sensitive. When you service the system board, avoid any kind of rough handling.
Table 28. Removal steps of system board, fan assembly, and base cover assembly 2 1 Step Screw (quantity) Color Torque 1 M2 × 6 mm, bind-head, nylon-coated (1) Black 0.167 Nm (1.7 kgfcm) 2 M2 × 3 mm, small-head, nylon-coated (1) Silver 0.167 Nm (1.7 kgfcm) In step 3 , remove the system board and fan assembly together from the base cover assembly.
Table 28. Removal steps of system board, fan assembly, and base cover assembly (continued) 4 4 4 Step Screw (quantity) Color Torque 4 M2 × 4 mm, bind-head, nylon-coated (3) Black 0.167 Nm (1.7 kgfcm) Turn the system board over, and then disconnect the fan assembly from the system board. 6 5 When installing: Make sure that the fan connector is attached to the system board firmly.
Table 29. Application of the thermal grease When installing: Before you attach the fan assembly to the computer, apply thermal grease, at an amount of 0.2 grams, on the part marked a as in the following figure. Either too much or too less application of grease can cause a thermal problem due to imperfect contact with a component.
Note: Applying labels to the base cover The new base cover FRU is shipped with a kit containing labels of several kinds. When you replace the base cover, you need to apply the following labels: 11 Homologation label 13 Product label Following labels need to be peeled off from the old base cover, and need to be put on the new base cover.
2010 LCD bezel assembly For access, remove these FRUs in order: v “1010 Battery pack” on page 61 v “1020 Optical drive or second battery or travel cover” on page 62 Table 30. Removal steps of LCD bezel assembly 1 2 2 1 2 2 Step Screw cap Screw (quantity) Color Torque 1 M2 × 4 mm, small-head, nylon-coated (2) Black 0.167 Nm (1.7 kgfcm) 2 M2 × 3 mm, small-head, nylon-coated (4) Silver 0.167 Nm (1.
2020 LCD panel and LCD cable For access, remove these FRUs, in order: v “1010 Battery pack” on page 61 v “1020 Optical drive or second battery or travel cover” on page 62 v “1050 PCI Express Mini Card for wireless LAN” on page 67 v “1060 Wireless USB adapter or Intel Turbo Memory” on page 70 v “1070 Keyboard” on page 73 v “1090 PCI Express Mini Card for wireless WAN” on page 78 v “1100 Palm rest or palm rest with fingerprint reader” on page 80 v “1120 Keyboard bezel” on page 83 v “1150 LCD assembly” on page
Table 31. Removal steps of LCD panel and LCD cable 1 Attention: Unplug the LCD cable with holding the left and right edges of the connector with your fingers, and gently pull the connector toward you. DO NOT unplug it with pulling the cable. Applying tension could cause the cable to be damaged or a wire to be broken, and it might cause the S-driver to be damaged.
Table 31. Removal steps of LCD panel and LCD cable (continued) 3 4 5 Step Screw (quantity) Color Torque 3 M2 × 3 mm, small-head, nylon-coated (1) Silver 0.167 Nm (1.7 kgfcm) When installing: Make sure that the connector is attached firmly.
Table 31. Removal steps of LCD panel and LCD cable (continued) Cable routing: When you install the LCD cable, route the cable as shown in this figure.
2030 Integrated camera For access, remove these FRUs, in order: v “1010 Battery pack” on page 61 v “1020 Optical drive or second battery or travel cover” on page 62 v “1050 PCI Express Mini Card for wireless LAN” on page 67 v “1060 Wireless USB adapter or Intel Turbo Memory” on page 70 v “1070 Keyboard” on page 73 v “1090 PCI Express Mini Card for wireless WAN” on page 78 v “1100 Palm rest or palm rest with fingerprint reader” on page 80 v “1120 Keyboard bezel” on page 83 v “1150 LCD assembly” on page 89 v
2040 Antenna assembly For access, remove these FRUs in order: v “1010 Battery pack” on page 61 v “1020 Optical drive or second battery or travel cover” on page 62 v “1050 PCI Express Mini Card for wireless LAN” on page 67 v “1060 Wireless USB adapter or Intel Turbo Memory” on page 70 v “1070 Keyboard” on page 73 v “1090 PCI Express Mini Card for wireless WAN” on page 78 v “1100 Palm rest or palm rest with fingerprint reader” on page 80 v “1120 Keyboard bezel” on page 83 v “1150 LCD assembly” on page 89 v “2
Table 33.
Table 33. Removal steps of antenna assembly (continued) Cable routing: When you install the antenna assembly, route the cables as shown in this figure.
2050 Hinge L and hinge R For access, remove these FRUs in order: v “1010 Battery pack” on page 61 v “1020 Optical drive or second battery or travel cover” on page 62 v “1050 PCI Express Mini Card for wireless LAN” on page 67 v “1060 Wireless USB adapter or Intel Turbo Memory” on page 70 v “1070 Keyboard” on page 73 v “1090 PCI Express Mini Card for wireless WAN” on page 78 v “1100 Palm rest or palm rest with fingerprint reader” on page 80 v “1120 Keyboard bezel” on page 83 v “1150 LCD assembly” on page 89 v
Table 34.
2060 LED sub card, LED cable and LCD cover assembly For access, remove these FRUs in order: v “1010 Battery pack” on page 61 v “1020 Optical drive or second battery or travel cover” on page 62 v “1050 PCI Express Mini Card for wireless LAN” on page 67 v “1060 Wireless USB adapter or Intel Turbo Memory” on page 70 v “1070 Keyboard” on page 73 v “1090 PCI Express Mini Card for wireless WAN” on page 78 v “1100 Palm rest or palm rest with fingerprint reader” on page 80 v “1120 Keyboard bezel” on page 83 v “1150
Table 35. Removal steps of LED sub card, LED cable, and LCD cover assembly (continued) Cable routing: When you install the microphone module, route the cable as shown in this figure.
Locations Front view 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 Integrated camera ThinkLight Status indicators Note: For the description of each indicator, see “Status indicators” on page 49.
Rear view 1 2 3 4 5 6 7 8 9 10 11 Status indicators Note: For the description of each indicator, see “Status indicators” on page 49.
Parts list This section contains following lists of the service parts. v “Overall” on page 116 v “LCD FRUs” on page 124 v “Keyboard” on page 126 v “Miscellaneous parts” on page 127 v “AC adapters” on page 129 v “Power cords” on page 130 v “Recovery discs” on page 131 v “Common service tools” on page 134 Notes: v Each FRU is available for all types or models, unless specific types or models are specified.
Overall 1 22 21 20 2 19 3 18 4 17 5 16 6 15 7 14 b 8 13 9 12 a 10 11 116 ThinkPad X301 Hardware Maintenance Manual
Table 36. Parts list—Overall No. FRU FRU no. RoHS ID CRU ID 45N3056 R N a, b See “Miscellaneous parts” on page 127. 1 LCD unit (see “LCD FRUs” on page 124.
Table 36. Parts list—Overall (continued) No. 118 FRU FRU no. RoHS ID CRU ID 5 System board assembly with 1.4 GHz CPU, non-AMT, non-TPM v 2774-CTO v 2776-CTO, P9x v 2777-CTO v 2778-CTO v 2779-CTO v 4057-CTO v 4182-CTO 42W8114 R N 5 System board assembly with 1.
Table 36. Parts list—Overall (continued) No. FRU FRU no.
Table 36. Parts list—Overall (continued) No. FRU FRU no.
Table 36. Parts list—Overall (continued) No. FRU FRU no.
Table 36. Parts list—Overall (continued) No. 122 FRU FRU no. RoHS ID CRU ID 13 MicroSATA hard disk drive, 120 GB, 5,400 rpm v 2774-CTO v 2776-CTO v 2777-CTO v 2778-CTO v 2779-CTO v 4057-CTO v 4182-CTO 42T1323 R ** 14 Speaker assembly 42X4670 R N 15 Fan 44C0747 R N 16 Audio sub card 42W7992 R N 17 Audio FPC 44C4047 R N 18 Bluetooth daughter card (BDC-2.
Table 36. Parts list—Overall (continued) No. FRU FRU no. RoHS ID CRU ID — Thermal grease 91P8835 R N — AC adapter (see “AC adapters” on page 129.
LCD FRUs 1 2 3 10 9 8 7 4 a 5 6 13.3-inch WXGA+ TFT Table 37. Parts list—13.3-inch WXGA+ TFT No. 124 FRU FRU no. RoHS ID CRU ID 1 LCD bezel assembly 44C0862 R N 2 LCD module, 13.
Table 37. Parts list—13.3-inch WXGA+ TFT (continued) No. FRU FRU no.
Keyboard 126 Language P/N RoHS ID CRU ID Arabic 42T3615 R ** Belgian 42T3612 Brazilian Portuguese 42T3631 Canadian French (058) 42T3602 Canadian French (Acnor) 42T3601 Czech 42T3620 Danish 42T3609 Dutch 42T3606 Finnish, Swedish 42T3607 French 42T3605 German 42T3603 Greek (U.S.
Miscellaneous parts Table 38.
Table 38.
Table 38. Parts list—Miscellaneous parts (continued) FRU P/N RoHS ID CRU ID LCD miscellaneous parts: v (a) Heat spreader for camera v ThinkPad logo v Lenovo logo v Label (camera) v Label (no camera) v Label (LED) v Tape cable fix (10 × 38) v LCD latch R v LCD latch L v Rubber 0.5 v Rubber 0.8 v Rubber 0.8 long v Rubber 1.0 v Rubber 1.
Power cords A ThinkPad power cord for a specific country or region is usually available only in that country or region: Table 41. Parts list—2-pin power cords Region P/N Argentina v models -CTO, xxY 42T5020 42T5105 Brazil v models -CTO, xxP 42T5180 42T5183 Canada, U.S. v models -CTO, xxF, xxL, xxS, xxU 42T5008 42T5093 Japan v models -Exx, Jxx 42T5014 42T5099 RoHS ID CRU ID R * RoHS ID CRU ID R * Table 42.
Recovery discs Windows XP Professional DVDs Windows XP Professional is preinstalled as the operating system in the following models: v 2774-CTO, LDx, P1x, P2x, P3x, P4x, P5x, P6x, P7x, P8x, P9x, PAx, PBx, PCx, PDx, PEx, PFx, PGx, N3x, N4x v 2776-CTO, L8x, P1x, P2x, P3x, P4x, P5x, P6x, P7x, P8x, P9x v 2777-CTO, L2x, P1x, P2x, P3x, P4x, P5x, P6x, P7x v 2778-CTO v 2779-CTO v 4057-CTO, LDx, N2x v 4182-CTO, P1x, P2x, P3x, P4x, P5x, P6x, P7x Table 43.
Windows Vista Business (32 bit) DVDs Windows Vista Business (32 bit) is preinstalled as the operating system in the following models: v 2774-CTO, 11x, 12x, 13x, 14x, 15x, 16x, 17x, 18x, 19x, 1Ax, 1Bx, 1Ex, 1Fx, 1Gx, 1Hx, 1Jx, 1Kx, 1Lx, 1Mx, 1Nx, 1Px, 1Tx, 1Ux, 1Vx, 1Wx, 1Yx, 1Zx, 24x, 25x, L2x, L5x, LEx, L7x, LBx, LCx, N1x, N2x v 2776-CTO, L5x, L6x, L7x, L9x, LAx, LBx, LCx, LEx, LFx, N1x, N4x, N5x, T1x, T2x, T3x, T4x, T5x, T6x, T7x, T8x, T9x, TAx, TDx, TEx, TFx, TGx, TJx, TMx, TSx, V1x v 2777-CTO, L1x, T1x,
Windows Vista Ultimate (32 bit) DVDs Windows Vista Ultimate (32 bit) is preinstalled as the operating system in the following models: v 2774-CTO, 1Sx, L4x, L8x, LFx v 2776-CTO, TCx, L1x, L3x v 2777-CTO v 2778-CTO v 2779-CTO v 4057-CTO v 4182-CTO Table 45.
Common service tools Table 46. Parts list—Common service tools Tool P/N Screwdriver kit 95F3598 1/4″ drive spinner handle 1650840 1/4″ Sq. to 1/4″ hex torx adapter 93F2838 TR7-TR-10 tamper resistant torx bits 00P6967 Removal tool antenna RF connector 08K7159 USB 2.
Notices Lenovo may not offer the products, services, or features discussed in this document in all countries. Consult your local Lenovo representative for information on the products and services currently available in your area. Any reference to a Lenovo product, program, or service is not intended to state or imply that only that Lenovo product, program, or service may be used.
vary significantly. Some measurements may have been made on development-level systems and there is no guarantee that these measurements will be the same on generally available systems. Furthermore, some measurements may have been estimated through extrapolation. Actual results may vary. Users of this document should verify the applicable data for their specific environment.
Part Number: 43Y9441_01 (1P) P/N: 43Y9441_01
