User Guide ThinkPad E550, E555, and E550c
Note: Before using this information and the product it supports, be sure to read and understand the following: • Safety, Warranty, and Setup Guide • Regulatory Notice • “Important safety information” on page vi • Appendix F “Notices” on page 153 The latest Safety, Warranty, and Setup Guide and the Regulatory Notice are available on the Lenovo® Support Web site at: http://www.lenovo.com/UserGuides Third Edition (July 2015) © Copyright Lenovo 2014, 2015.
Contents Read this first . . . . . . . . . . . . . . v Important safety information . . . . . . . . Conditions that require immediate action . Safety guidelines . . . . . . . . . . . Service and upgrades . . . . . . . . . Power cords and power adapters . . . . Extension cords and related devices . . . Plugs and outlets . . . . . . . . . . . Power supply statement . . . . . . . . External devices . . . . . . . . . . . General battery notice . . . . . . . . . Notice for removable rechargeable battery .
Hard disk security . . . . . . . . . . . . Using the fingerprint reader. . . . . . . . . Notice on deleting data from your storage drive. Using firewalls . . . . . . . . . . . . . . Protecting data against viruses . . . . . . . . . . . . 55 56 58 59 59 Chapter 6. Advanced configuration . . 61 Installing a new operating system . . . . . . Installing the Windows 7 operating system . Installing the Windows 8.1 or Windows 10 operating system . . . . . . . . . . . Installing device drivers . . . . . . . . .
Electronic emission notices. . . . . . . . . . Federal Communications Commission Declaration of Conformity . . . . . . . . Industry Canada Class B emission compliance statement . . . . . . . . . . . . . . . European Union - Compliance to the Electromagnetic Compatibility Directive . . . German Class B compliance statement . . . Class 1 laser product compliance statement . . . . . . . . . . . . . . . Korea Class B compliance statement . . . . Japan VCCI Class B compliance statement . .
iv User Guide
Read this first Be sure to follow the important tips given here to get the most use and enjoyment out of your computer. Failure to do so might lead to discomfort or injury, or cause your computer to fail. Protect yourself from the heat that your computer generates. When your computer is turned on or the battery is charging, the base, the palm rest, and some other parts may become hot. The temperature they reach depends on the amount of system activity and the level of charge in the battery.
Protect your computer and data when moving it. Before moving a computer equipped with a hard disk drive or hybrid drive, do one of the following: • Turn off the computer. • Put the computer in sleep mode. • Put the computer in hibernation mode. This will help to prevent damage to the computer, and possible loss of data. Handle your computer gently. Do not drop, bump, scratch, twist, hit, vibrate, push, or place heavy objects on your computer, display, or external devices. Carry your computer carefully.
Conditions that require immediate action Products can become damaged due to misuse or neglect. Some product damage is serious enough that the product should not be used again until it has been inspected and, if necessary, repaired by an authorized servicer. As with any electronic device, pay close attention to the product when it is turned on. On very rare occasions, you might notice an odor or see a puff of smoke or sparks vent from your product. Or you might hear sounds like popping, cracking or hissing.
sure that the power is turned off and that the product is unplugged from any power source. If you have any questions or concerns, contact the Customer Support Center. Although there are no moving parts in your computer after the power cord has been disconnected, the following warnings are required for your safety. CAUTION: Hazardous moving parts. Keep fingers and other body parts away. CAUTION: Before you open the computer cover, turn off the computer and wait several minutes until the computer is cool.
Extension cords and related devices Ensure that extension cords, surge protectors, uninterruptible power supplies, and power strips that you use are rated to handle the electrical requirements of the product. Never overload these devices. If power strips are used, the load should not exceed the power strip input rating. Consult an electrician for more information if you have questions about power loads, power requirements, and input ratings.
External devices CAUTION: Do not connect or disconnect any external device cables other than USB and 1394 cables while the computer power is on; otherwise, you might damage your computer. To avoid possible damage to attached devices, wait at least five seconds after the computer is shut down to disconnect external devices. General battery notice DANGER Batteries supplied by Lenovo for use with your product have been tested for compatibility and should only be replaced with approved parts.
Notice for non-rechargeable coin-cell battery DANGER If the coin-cell battery is incorrectly replaced, there is danger of an explosion. The battery contains a small amount of harmful substance. Do not heat to more than 100°C (212°F). The following statement applies to users in the state of California, U.S.A. California Perchlorate Information: Products containing manganese dioxide lithium coin-cell batteries may contain perchlorate. Perchlorate Material - special handling may apply, See www.dtsc.ca.
• Do not operate your computer inside furniture, as this might increase the risk of overheating. • Airflow temperatures into the computer should not exceed 35°C (95°F). Electrical current safety information DANGER Electric current from power, telephone, and communication cables is hazardous. To avoid a shock hazard: • Do not use your computer during a lightning storm.
Laser safety information CAUTION: When laser products (such as CD-ROM drives, DVD drives, 3D cameras, fiber optic devices, or transmitters) are installed, note the following: • Do not remove the covers. Removing the covers of the laser product could result in exposure to hazardous laser radiation. There are no serviceable parts inside the device. • Use of controls or adjustments or performance of procedures other than those specified herein might result in hazardous radiation exposure.
If your Lenovo computer came with headphones or earphones in the package, as a set, the combination of the headphones or earphones and the computer already complies with the specifications of EN 50332-1. If different headphones or earphones are used, ensure that they comply with EN 50332-1 (Clause 6.5 Limitation Values). Using headphones that do not comply with EN 50332-1 can be dangerous due to excessive sound pressure levels. Additional safety information DANGER Plastic bags can be dangerous.
Chapter 1. Product overview This chapter provides information about locations of connectors, locations of important product labels, computer features, specifications, operating environment, and preinstalled programs.
9 Trackpad 10 Media-card slot 11 Speakers 1 Microphones The microphones capture sound and voice when used with a program capable of handling audio. 2 2D camera Use the camera to take pictures or hold a video conference. For more information, see “Using the camera” on page 38. ThinkPad pointing device 3 TrackPoint pointing stick TrackPoint buttons (available on some models) 9 Trackpad 8 The keyboard contains the Lenovo unique ThinkPad® pointing device.
11 Speakers Your computer is equipped with a pair of stereo speakers. Front view for models with a 3D camera Figure 2.
ThinkPad pointing device 6 TrackPoint pointing stick 11 TrackPoint buttons (available 12 on some models) Trackpad The keyboard contains the Lenovo unique ThinkPad pointing device. Pointing, selecting, and dragging are all part of a single process that you can perform without moving your fingers from a typing position. For more information, see “Using the thinkPad pointing device” on page 22. 7 Power button Press the power button to turn on the computer or put the computer into sleep mode.
Right-side view Figure 3. Right-side view 1 Combo audio connector 2 Optical drive (available on some models) 3 USB 2.0 connector 4 ac power connector 5 Lenovo OneLink connector 1 Combo audio connector Connect a headphones or a headset that has a 3.5-mm (0.14-inch) 4-pole plug to the audio connector to listen to the sound from the computer. Notes: • If you are using a headset with a function switch, do not press this switch while using the headset.
4 5 ac power connector Lenovo OneLink connector When the ac power adapter is connected to the ac power connector, it provides power to the computer and charges the battery. When a supported ThinkPad OneLink Dock or ThinkPad OneLink Pro Dock is connected to the Lenovo OneLink connector, it can not only extend the computer capabilities but also provide ac power to the computer and charge the battery. To use the Lenovo OneLink connector, remove the connector cover from the Lenovo OneLink connector first.
2 Fan louvers The fan louvers and the internal fan enable air to circulate in the computer to ensure proper cooling, especially the cooling of the microprocessor. Note: To ensure proper airflow, do not place any obstacle in front of the fan louvers. 3 Ethernet connector Connect the computer to a local area network (LAN) with the Ethernet connector. DANGER To avoid the risk of electrical shock, do not connect the telephone cable to the Ethernet connector.
For instructions on how to start the programs, see “Accessing Lenovo programs” on page 14. Note: When you attach a USB cable to this USB connector, ensure that the USB mark is facing upward. Otherwise the connector might get damaged. Bottom view Figure 5. Bottom view 1 1 Battery 2 Memory-upgrade slots 3 Storage drive 4 Wireless-LAN-card slot Battery Use your computer with battery power whenever ac power is unavailable.
Status indicators The status indicators show the current status of your computer. 1 Fn Lock indicator The Fn Lock indicator shows the status of Fn Lock function. For more information, see “Special keys” on page 19. 2 Speaker-mute indicator When the speaker-mute indicator is on, the speakers are muted. 3 Microphone-mute indicator When the microphone-mute indicator is on, the microphones are muted. 4 Camera-status indicator When the camera-status indicator is on, the camera is in use.
• Off: The computer is off or in hibernation mode. • Blinks fast: The computer is entering hibernation mode. • Blinks slowly: The computer is in sleep mode. Locating important product information This section provides information to help you locate the following labels that contain important product information: Machine type and model information The machine type and model label identifies your computer.
For a preinstalled wireless module, this label identifies the actual FCC ID and IC certification number for the wireless module installed by Lenovo. Note: Do not remove or replace a preinstalled wireless module by yourself. For module replacement, you must contact Lenovo service first. Lenovo is not responsible for any damage caused by unauthorized replacement.
In some cases, an earlier Windows version might be preinstalled under the terms of the Windows 8 Pro, Windows 8.1 Pro, or Windows 10 Pro license downgrade rights. Features This topic lists the features of your computer. To view the system properties of your computer, do the following: • For Windows 7: Click Start and right-click Computer. Then click Properties. • For Windows 8.1: From the desktop, move the pointer to the top-right or bottom-right corner of the screen to bring up the charms.
• One USB 2.0 connector • One USB 3.0 connector • RJ45 Ethernet connector • Integrated microphones • 2D camera or 3D camera, depending on the model Note: The 3D camera is an infrared laser device. Optical drive (available on some models) • Multi-Burner drive Wireless features • Integrated wireless LAN • Integrated Bluetooth Security features • Fingerprint reader (available on some models) Specifications This section lists the physical specifications for your computer. Size • Width: 377 mm (14.
Note: When you charge the battery, its temperature must be at least 10°C (50°F). • Relative humidity: – Operating: 8% to 80% – Storage: 5% to 95% If possible, place your computer in a well-ventilated and dry area without direct exposure to sunshine. Attention: • Keep electrical appliances such as an electric fan, radio, air conditioner, and microwave oven away from the computer. The strong magnetic fields generated by these appliances can damage the monitor and data on the hard disk drive or hybrid drive.
Access Connections™ (Windows 7) The Access Connections program is a connectivity assistant program for creating and managing location profiles. Each location profile stores all the network and Internet configuration settings needed for connecting to a network infrastructure from a specific location such as a home or an office.
Lenovo Settings (Windows 8.1 and Windows 10) Lenovo Solution Center (Windows 7, Windows 8.1, and Windows 10) Mobile Broadband Connect The Lenovo Settings program enables you to enhance your computing experience by turning your computer into a portable hotspot, configuring camera and audio settings, optimizing your power settings, and creating and managing multiple network profiles. The Lenovo Solution Center program enables you to troubleshoot and resolve computer problems.
Chapter 2. Using your computer This chapter provides information on using some of the computer components.
How to turn off my computer? • For Windows 7: Open the Start menu, then click Shut down. • For Windows 8.1: Do one of the following: – Go to the Start screen by pressing the Windows key, click the power icon in the top-right corner of the screen, then click Shut down. – Move your pointer to the top-right or bottom-right corner of the screen to display the charms. Then click Settings ➙ Power ➙ Shut down.
Can I change the Windows 8.1 startup behavior to open either the desktop or the Start screen? On the Windows 8.1 operating system, you can set the computer to open either the desktop or the Start screen by default. To set the default startup screen, do the following: 1. On the desktop, move your pointer to the taskbar at the bottom of the screen and right-click on the taskbar. 2. Click Properties. The Taskbar and Navigation properties window is displayed. 3.
1 Additional shortcut keys Your computer might have four additional shortcut keys: • : Launches calculator • : Locks operating system • : Opens the default browser • : Opens Computer 2 Numeric keypad You can use this numeric keypad to input numbers quickly. 3 Windows key For Windows 7 and Windows 10: Press the Windows key to open the Start menu. For Windows 8.1: Press the Windows key to switch between the current workspace and the Start screen.
When the Fn Lock function is enabled: The Fn Lock indicator turns on. To input F1-F12, press the function keys directly. To initiate the special function printed as an icon on each key, press the Fn key and the corresponding function key. : Mutes or unmutes the speakers. When the speakers are muted, the speaker-mute indicator turns • on. If you mute the sound and turn off your computer, the sound will remain muted when you turn on your computer again. To turn on the sound, press F1, F2, or F3.
ThinkPad pointing device The ThinkPad pointing device enables you to perform all the functions of a traditional mouse, such as moving the pointer, left-clicking, right-clicking, and scrolling. With the ThinkPad pointing device, you also can perform a variety of touch gestures, such as rotating and zooming in or out. Using the thinkPad pointing device Depending on the model, the pointing device on your computer might look like either of the following illustrations.
ThinkPad pointing device with TrackPoint buttons This type of ThinkPad pointing device consists of the following components: 1 2 TrackPoint pointing device Trackpad By default, both the TrackPoint pointing device and the trackpad are active with the touch gestures enabled. To change the settings, see “Customizing the ThinkPad pointing device” on page 28.
• Point Use the TrackPoint pointing stick 1 to move the pointer on the screen. To use the pointing stick, apply pressure to the pointing-stick nonslip cap in any direction parallel to the keyboard. The pointer moves accordingly but the pointing stick itself does not move. The speed at which the pointer moves depends on the amount of pressure you apply to the pointing stick. • Left-click Press the left-click button 2 to select or open an item.
With the trackpad, you also can perform a variety of touch gestures. For information about using the touch gestures, see “Trackpad touch gestures” on page 27.
1 Point Use the pointing stick to move the pointer on the screen. To use the pointing stick, apply pressure to the pointing stick nonslip cap in any direction parallel to the keyboard. The pointer moves accordingly but the pointing stick itself does not move. The speed at which the pointer moves depends on the amount of pressure you apply to the pointing stick. 2 Scroll Press and hold the dotted scrolling bar while applying pressure to the pointing stick in the vertical or horizontal direction.
1 Point Use the pointing stick to move the pointer. To use the pointing stick, apply pressure to the nonslip cap on the pointing stick in any direction parallel to the keyboard. The pointer moves accordingly but the pointing stick itself does not move. The speed at which the pointer moves depends on the amount of pressure you apply to the pointing stick. 2 Scroll Press and hold the dotted scrolling bar while applying pressure to the pointing stick in the vertical or horizontal direction.
Swipe from the top edge From the Start screen or the current app, swipe in from the top edge of the trackpad with one finger to display the command menu. Swipe from the top to the bottom edge Swipe from the top to the bottom edge of the trackpad with one finger to close the current app. Performing this gesture on the desktop closes the desktop and displays the Start screen. Swipe from the right edge Swipe in from the right edge of the trackpad with one finger to display the charms.
Power management When you use your computer away from electrical outlets, you depend on battery power to keep your computer running. Different computer components consume power at different rates. The more you use the power-intensive components, the faster you consume battery power. Spend more time unplugged with ThinkPad batteries. Mobility has revolutionized business by enabling you to take your work wherever you go.
– When the battery icon in the Windows notification area shows a low percentage of battery power remaining. – When the batteries have not been used for a long time Checking the battery status Move your pointer to the battery-status icon in the Windows notification area to check the battery status. The battery-status icon displays the percentage of battery power remaining and how long you can use your computer before you must charge the battery.
Power-saving modes There are several modes that you can use at any time to conserve power. This section introduces each mode and gives tips on the effective use of battery power. • Screen blank mode (for Windows 7 only) The computer display requires considerable battery power. To turn off the power to the display and make the computer enter screen blank mode, right-click the battery-gauge icon in the windows notification area and select Power off display.
systems. If an unauthorized battery or a battery designed for another system is installed, the system will not charge. Attention: Lenovo has no responsibility for the performance or safety of unauthorized batteries, and provides no warranties for failures or damage arising out of their use. Note: If an unauthorized battery is installed, the following message will be displayed: “The battery installed is not supported by this system and will not charge.
DANGER Do not put the battery in trash that is disposed of in landfills. When disposing of the battery, comply with local ordinances or regulations and your company's safety standards. DANGER There is a danger of an explosion if the coin-cell battery is incorrectly placed. The lithium battery contains lithium and can explode if it is not properly handled, or disposed of. Replace only with a battery of the same type.
Your computer comes with a built-in wireless network card and a configuration utility to help you establish wireless connections and monitor the connection status. This enables you to stay connected to your network while you are at the office, in a meeting room, or at home, with no need for a wired connection. To establish a wireless-LAN connection, do the following: 1. Click the wireless-network-connection-status icon in the Windows notification area. A list of available wireless networks is displayed. 2.
• Power to the wireless radio is on. No signal. • Power to the wireless radio is on. The signal strength of the wireless connection is excellent. • Power to the wireless radio is on. The signal strength of the wireless connection is marginal. • Power to the wireless radio is on. The signal strength of the wireless connection is poor. To improve signal strength, move your computer closer to the wireless access point.
For more information about the external display, refer to the manuals provided with it. Connecting an external display You can use either a wired display or a wireless display. The wired display can be connected to the HDMI or VGA connector by a cable. The wireless display can be added through the Wi-Di or Miracast function. • Connecting a wired display Note: When you connect an external monitor, a video interface cable with a ferrite core is required. 1.
• Extend: Extends the video output from your computer display to an external display. You can drag and move items between the two displays. • Projector only: Shows the video output only on an external display. Note: Depending on the situation, you might see Projector only or Second screen only. Note: If you show DOS or programs using DirectDraw or Direct3D® in full-screen mode, only the main display shows the video output.
Configuring for sound recording To configure the microphone for optimal sound recording, use the SmartAudio program. To start the program, go to Control Panel and click Hardware and Sound ➙ SmartAudio. Using the camera Depending on the model, your computer comes with a 2D camera or a 3D camera. The 3D camera works with certain third-party apps, such as apps provided by Intel. The performance parameters of the 3D camera vary depending on the app you use.
Using a flash media card Your computer has one media card reader slot.
5. Remove the card and store it safely for future use. Note: If you do not remove the card from your computer after you eject the card from the Windows operating system, the card can no longer be accessed. To access the card, you must remove it first, then insert it again.
Chapter 3. Enhancing your computer This chapter provides instructions on how to use hardware devices to expand your computer capabilities. • “Finding ThinkPad options” on page 41 • “ThinkPad OneLink Dock” on page 41 • “ThinkPad OneLink Pro Dock” on page 42 Finding ThinkPad options If you want to expand the capabilities of your computer, Lenovo has a number of hardware accessories and upgrades to meet your needs.
2 USB 3.0 connector: Used to connect devices that are compatible with USB 3.0 and USB 2.0. 3 Always On USB connector: By default, the Always On USB connector enables you to charge some mobile digital devices and smartphones no matter when your computer is in sleep mode, hibernation mode, or is off. For more information, refer to the documentation that comes with the dock. 4 Combo audio connector: Used to connect headphones or a headset that has a 3.5-mm (0.14-inch), 4-pole plug.
Front view 1 Security-lock slot: To protect your dock from theft, you can purchase a security cable lock, such as a Kensington-style cable lock, that fits this security-lock slot to lock your dock to a desk, table, or other non-permanent fixture. 2 USB 3.0 connector: Used to connect devices that are compatible with USB 3.0 and USB 2.0.
1 USB 2.0 connectors: Used to connect devices that are compatible with USB 2.0. 2 USB 3.0 connectors: Used to connect devices that are compatible with USB 3.0 and USB 2.0. 3 Ethernet connector: Used to connect the dock to an Ethernet LAN. The indicators on this connector have the same function as the ones on the computer. 4 DisplayPort® connector: Used to attach a high-performance monitor, a direct-drive monitor, or other devices that use a DisplayPort connector.
Chapter 4. You and your computer This chapter provides information about accessibility, comfort, and travelling with your computer. Accessibility and comfort Good ergonomic practice is important to get the most from your personal computer and to avoid discomfort. Arrange your workplace and the equipment you use to suit your individual needs and the kind of work that you perform. In addition, use healthy work habits to maximize your performance and comfort while using your computer.
Arm and hand position: If available, use chair arm rests or an area on your working surface to provide weight support for your arms. Keep your forearms, wrists, and hands in a relaxed and neutral (horizontal) position. Type with a soft touch without pounding the keys. Leg position: Keep your thighs parallel to the floor and your feet flat on the floor or on a footrest.
Keyboard shortcut Function Shift five times Turn on or turn off Sticky Keys Num Lock for five seconds Turn on or turn off Toggle Keys Left Alt+Left Shift+Num Lock Turn on or turn off Mouse Keys Left Alt+Left Shift+PrtScn (or PrtSc) Turn on or turn off High Contrast For more information, go to http://windows.microsoft.com/, and then type any of the following keywords for searching: keyboard shortcuts, key combinations, shortcut keys.
To use Speech Recognition, do the following: 1. Go to Control Panel, and ensure that you view Control Panel by Category. 2. Click Ease of Access ➙ Speech Recognition. 3. Follow the instructions on the screen. Screen-reader technologies Screen-reader technologies are primarily focused on software program interfaces, help information systems, and various online documents. For additional information about screen readers, see the following: • Using PDFs with screen readers: http://www.adobe.com/accessibility.
If your mouse has a wheel, press and hold Ctrl, and then scroll the wheel to change the item size. Industry-standard connectors Your computer provides industry-standard connectors that enable you to connect assistive devices. For more information about the location and function of the connectors, see “Locating computer controls, connectors, and indicators” on page 1.
• Extra battery, charged • A quality carrying case that provides adequate cushion and protection • External storage device If you are traveling to another country, you might want to consider an ac power adapter for the country to which you are travelling. To purchase travel accessories, go to http://www.lenovo.com/accessories.
Chapter 5. Security This chapter provides information about how to protect your computer from theft and unauthorized use. • “Using passwords” on page 51 • “Hard disk security” on page 55 • “Using the fingerprint reader” on page 56 • “Notice on deleting data from your storage drive” on page 58 • “Using firewalls” on page 59 • “Protecting data against viruses” on page 59 Using passwords You can help prevent your computer from unauthorized use by using passwords.
• To set a password, do the following: a. In the Enter New Password field, type a desired password and press Enter. b. In the Confirm New Password field, retype the password and press Enter. • To change a password, do the following: a. In the Enter Current Password field, type the current power-on password and press Enter. b. In the Enter New Password field, type the new power-on password and press Enter; then retype the password in the Confirm New Password field and Press Enter.
– Security mode – Fingerprint reader priority Notes: • The system administrator can set the same supervisor password on many ThinkPad notebook computers to make administration easier. • When Lock UEFI BIOS Settings option is enabled, all BIOS settings cannot be changed. To change the settings, a supervisor password is required. Setting, changing, or removing a supervisor password Before you start, print these instructions. Only a system administrator can set, change, or remove a supervisor password.
drive in a system like a master key. The administrator sets the master password; then assigns a user password for each computer in the network. The user can then change the user password as desired, but the administrator still can get access by using the master password. When a master hard disk password is set, only the administrator can remove the user hard disk password. Setting a hard disk password Before you start, print these instructions. To set a hard disk password, do the following: 1.
1. Type the current master hard disk password in the Enter Current Password field and press Enter. 2. Type the new master hard disk password in the Enter New Password field and press Enter; then retype the new password you just entered in the Confirm New Password field and press Enter. 3. A Setup Notice window is displayed. Press Enter to continue. The master hard disk password is changed.
The hard disk drive built into your computer can be protected by UEFI BIOS. Using Windows BitLocker Drive Encryption To help protect your computer against unauthorized access, use the drive encryption software, such as Windows BitLocker Drive Encryption. Windows BitLocker Drive Encryption is an integral security feature of some editions of the Windows operating system. It can help you protect the operating system and data stored on your computer, even if your computer is lost or stolen.
Swiping your finger over the fingerprint reader To swipe your finger over the reader, do the following: 1. Place the top joint of your finger on the sensor. 2. Apply light pressure and swipe your finger toward you across the reader in one smooth motion. Do not lift your finger when you are swiping it. Maintaining the fingerprint reader The following actions could damage the fingerprint reader or cause it not to work properly: • Scratching the surface of the reader with a hard, pointed object.
• The reader often fails to enroll or authenticate your fingerprint. If your finger has any of the following conditions, you might not be able to register or authenticate it: • Your finger is wrinkled. • Your finger is rough, dry, or injured. • Your finger is stained with dirt, mud, or oil. • The surface of your finger is different from when you enrolled your fingerprint. • Your finger is wet. • A finger is used that has not been enrolled.
remains on the drive; however, it cannot be decrypted without the old key. This feature is also available with the Drive Erase Utility for Resetting the Cryptographic Key and Erasing the Solid State Drive tool. Using firewalls If your system is preinstalled with a firewall program, it protects against computer Internet security threats, unauthorized access, intrusions, and Internet attacks. It also protects your privacy.
60 User Guide
Chapter 6. Advanced configuration This chapter provides the following information to help you configure the computer: • “Installing a new operating system” on page 61 • “Installing device drivers” on page 63 • “Using the ThinkPad Setup program” on page 63 Installing a new operating system In some situations, you might need to install a new operating system. This topic provides instructions on how to install a new operating system.
Country or region Code Country or region Code China SC Netherlands NL Denmark DK Norway NO Finland FI Spain SP France FR Sweden SV Germany GR Taiwan and Hong Kong TC Italy IT United States US Japan JP Installing the Windows 8.1 or Windows 10 operating system Before you start, print these instructions. Attention: • The process of installing a new operating system deletes all the data on your internal storage drive, including the data that were stored in a hidden folder.
Italy IT Japan JP United States US Installing device drivers Device driver is the program that operates a particular hardware device of the computer. If a device does not perform well or you install a new device, you need to install or update the corresponding device driver. For example, if you use the Windows 7 operating system, to use the USB 3.0 connector, you need to download and install the USB 3.0 driver. To download the latest device drivers, do the following: 1. Go to http://www.lenovo.
Main menu When you enter the ThinkPad Setup program, you will first see the Main menu as follows: • UEFI BIOS Version • UEFI BIOS Date (Year-Month-Day) • Embedded Controller Version • ME Firmware Version • Machine Type Model • System-unit serial number • System board serial number • Asset Tag • CPU Type • CPU Speed • Installed memory • UUID • MAC address (Internal LAN) • Preinstalled OS License • UEFI Secure Boot Config menu To change the configuration of your computer, select the Config tab from the Think
Table 2. Config menu items (continued) Menu item Submenu item Selection Comments • The Wake on LAN function does not work when a hard disk password is set. Ethernet LAN Option ROM (for Legacy Only boot mode or Both with Legacy first) UEFI IPv4 Network Stack (for UEFI Only boot mode or Both with UEFI first) UEFI IPv6 Network Stack (for UEFI Only boot mode or Both with UEFI first) UEFI PXE Boot Priority (for Both with UEFI first boot mode, and IPv6 and IPv4 stacks are both enabled.
Table 2. Config menu items (continued) Menu item Submenu item Selection Comments If you select Disabled, it disables and hides the USB 3.0 controller, and USB 3.0 connectors will work as USB 2.0 connectors. Keyboard/Mouse TrackPoint • Disabled • Enabled Enable or disable the built-in TrackPoint pointing device. Note: If you want to use an external mouse, select Disabled. Trackpad • Disabled • Enabled Enable or disable the built-in trackpad.
Table 2. Config menu items (continued) Menu item Submenu item Selection Comments clock automatically when there are no computer activities. Normally, it is not necessary to change the setting. Intel Rapid Start Technology • Disabled • Enabled Enter after: • Immediately • 1 minute • 2 minutes • 5 minutes • 10 minutes • 15 minutes • 30 minutes • 1 hour To use this feature, a special partition on the solid-state drive is required.
Table 2. Config menu items (continued) Menu item Submenu item Selection Comments CPU Core Multi-Processing • Disabled If you select Enabled, additional execution core units within a microprocessor are enabled. • Enabled If you select Disabled, only one execution core unit within a microprocessor is enabled. Note: This sub-menu might be supported in models with an Intel CPU. Intel Hyper-Threading Technology • Disabled • Enabled If you select Enabled, additional microprocessor threads are enabled.
Table 3. Security menu items Menu item Submenu item Selection Comments Password Supervisor Password • Disabled Refer to “Supervisor password” on page 52. • Enabled Lock UEFI BIOS Settings • Disabled • Enabled Password at Unattended boot • Disabled Password at Restart • Disabled • Enabled • Enabled Password at Boot Device List • Disabled • Enabled Enable or disable the function that protects items in ThinkPad Setup from being changed by a user who does not have the supervisor password.
Table 3. Security menu items (continued) Menu item Submenu item Selection Comments Select Disabled to proceed without any user action required. Password Count Exceeded Error • Disabled • Enabled Select Enabled to show the POST 0199 error and prompt for the Security password. Select Disabled to hide the POST 0199 error and proceed without any user action required.
Table 3. Security menu items (continued) Menu item Submenu item Selection Comments Virtualization Intel Virtualization Technology • Disabled If you select Enabled, a Virtual Machine Monitor (VMM) can utilize the additional hardware capabilities provided by Virtualization Technology. • Enabled Note: This sub-menu is only supported in models with an Intel CPU. Intel VT-d Feature • Disabled • Enabled Intel VT-d is Intel Virtualization Technology for Directed I/O.
Table 3. Security menu items (continued) Menu item Submenu item Selection Comments Anti-Theft Computrace Module Activation • Disabled Enable or disable the UEFI BIOS interface to activate the computrace module. Computrace is an optional monitoring service from Absolute Software. • Enabled • Permanently Disabled Note: If you set the Computrace module activation to Permanently Disabled, you will be unable to enable this setting again.
Table 3. Security menu items (continued) Menu item Submenu item Selection Comments Clear All Secure Boot Keys • Yes This option is used to clear all keys and certificates in Secure Boot databases. You can install your own keys and certificates after selecting this option. • No Startup menu To change the startup settings of your computer, select the Startup tab from the ThinkPad Setup menu.
Table 4. Startup menu items (continued) Menu item Selection Comments UEFI/Legacy Boot • Both Select system boot capability. • UEFI Only • Both: Select priority of boot options between UEFI and Legacy. • Legacy Only UEFI/Legacy Boot Priority • UEFI First • Legacy First CSM Support (for UEFI Only) • No • Yes • UEFI Only: The computer will start from the UEFI-enabled operating system. • Legacy Only: The computer will boot from any operating system other than the UEFI-enabled one.
Note: Enable OS Optimized Defaults to meet the Windows 8 or Windows 10 certification requirement. When you change this setting, some other settings are changed automatically, such as CSM Support, UEFI/Legacy Boot, Secure Boot, and Secure RollBack Prevention. • Discard Changes: Discard the changes. • Save Changes: Save the changes. Updating the UEFI BIOS The UEFI BIOS is the first program that the computer runs when the computer is turned on.
76 User Guide
Chapter 7. Preventing problems An important part of owning a ThinkPad notebook computer is maintenance. With proper care, you can avoid common problems. The chapter provides information that can help you keep your computer running smoothly.
• For suspected hard disk drive or hybrid drive issues, refer to “Diagnosing problems” on page 83 and run a diagnostic test for the drive before you call the Customer Support Center. If your computer does not start up, download the files to create a bootable self-test medium from http://www.lenovo.com/hddtest. Run the test and record any messages or error codes.
Taking care of your computer Although your computer is designed to function reliably in normal work environments, you need to use common sense in handling it. By following the important tips in this topic, you will get the most use and enjoyment out of your computer. Be careful about where and how you work • Store packing materials safely out of the reach of children to prevent the risk of suffocation from plastic bags.
• Store your external and removable storage drive or optical drives in the appropriate containers or packaging when they are not being used. • Before you install any of the following devices, touch a metal table or a grounded metal object. This action reduces any static electricity from your body. The static electricity could damage the device.
Cleaning your computer keyboard To clean the computer keyboard, do the following: 1. Apply some isopropyl rubbing alcohol to a soft, dust-free cloth. Note: Avoid spraying cleaner directly onto the keyboard. 2. Wipe each keytop surface with the cloth. Wipe the keys one by one; if you wipe several keys at a time, the cloth might hook onto an adjacent key and possibly damage it. Make sure that no liquid drips onto or between the keys. 3. Allow to dry. 4.
82 User Guide
Chapter 8. Troubleshooting computer problems This chapter provides information on what to do if you experience a problem with your computer. • “Diagnosing problems” on page 83 • “Troubleshooting” on page 83 Diagnosing problems If you experience problems with your computer, use the Lenovo Solution Center program as a starting point for solving them. The Lenovo Solution Center program enables you to troubleshoot and resolve computer problems.
Note: Do not remove the battery and the ac power adapter or the battery and the dock to reset the computer. 2. While the computer is turned off, remove all power sources from the computer (battery and the ac power adapter or battery and the dock). Hold down the power button for 10 seconds. Plug in the ac power adapter or the dock while keeping the battery out of the computer. If the computer does not turn back on, continue with step 3.
Solution: Checksum of the Security settings in the EFI Variable is not correct. Enter ThinkPad Setup to check security settings, Press F10 and then press Enter to restart the system. If you still have a problem, have the computer serviced. • Message: 0187: EAIA data access error. Solution: The access to EEPROM is failed. Have the computer serviced. • Message: 0188: Invalid RFID Serialization Information Area. Solution: The EEPROM checksum is not correct (block # 0 and 1).
Solution: The hard disk drive is not working. Have the hard disk drive serviced. • Message: 2102: Detection error on HDD2 (Mini SATA). Solution: The Mini SATA device is not working. Have the Mini SATA device serviced. • Message: 2110: Read error on HDD0 (Main HDD). Solution: The hard disk drive is not working. Have the hard disk drive serviced. • Message: 2111: Read error on HDD1 (Ultrabay HDD) Solution: The hard disk drive is not working. Have the hard disk drive serviced.
3. Show the additional plans, then choose High performance. • Problem: When I turn on the computer, nothing is displayed on the screen and the computer does not beep while starting up. Note: If you are not sure whether you heard any beeps, turn off the computer by pressing and holding the power button for four seconds or more. Then turn on the computer and listen again. Solution: Ensure that: – The battery is installed correctly.
Memory module problems Print these instructions now and keep it with your computer for reference later. If your memory module is not operating properly, check the following items: 1. Verify that the memory module is installed and seated correctly in your computer. It might be necessary to remove all added memory modules to test the computer with only the factory-installed memory modules, and then reinstall the memory module one at a time to ensure a proper connection. 2.
Solution: – Use Category 5 wiring and make sure that the network cable is securely connected. – Connect to a 1000 BASE-T hub/switch (not 1000 BASE-X). • Problem: The Wake On LAN feature is not working. Solution: Ensure that Wake On LAN is enabled in ThinkPad Setup. If it is, check with your LAN administrator for the necessary settings. • Problem: My computer is a Gigabit Ethernet model, it cannot connect to the network at 1000 Mbps. Instead, it connects at 100 Mbps. Solution: – Try another cable.
Solution: The Windows 7 operating system sends PIM items in XML format, but most Bluetooth-enabled devices handle PIM items in vCard format. If another Bluetooth-enabled device can receive a file through Bluetooth, a PIM item sent from the Windows 7 might be saved as a file with the extension .contact. Problems with the keyboard and other pointing devices The following are the most common problems with keyboards and other pointing devices.
Computer screen problems • Problem: The screen is blank. Solution: Do the following: – Press F7 to bring up the image. – If you are using the ac power adapter, or using the battery and the battery gauge shows that the battery is not depleted, press F6 to make the screen brighter. – If your computer is in sleep mode, press Fn to resume from the sleep mode. – If the problem persists, follow the solution for the following problem. • Problem: The screen is unreadable or distorted.
10. Click OK. • Problem: Incorrect characters are displayed on the screen. Solution: Did you install the operating system or program correctly? If they are installed and configured correctly, have the computer serviced. • Problem: The screen stays on even after you turn off your computer. Solution: Press and hold the power button for four seconds or more to turn off your computer; then turn it on again. • Problem: Missing, discolored, or bright dots appear on the screen every time you turn on your computer.
7. If more than one monitor type is displayed, select Generic PnP Monitor or Generic Non-PnP Monitor. 8. Click Properties. If you are prompted for an administrator password or confirmation, type the password or provide confirmation. 9. Click the Driver tab. 10. Click Update Driver. 11. Click Browse my computer for driver software, and then click Let me pick from a list of device drivers on my computer. 12. Clear the Show compatible hardware check box. 13. Select your monitor manufacturer and model. 14.
2. Turn on the external monitor and the computer. 3. Right-click on the desktop, and do the following: – For Windows 7 and Windows 8.1: Click Screen resolution. – For Windows 10: Click Display settings, show the displayed window in full screen, and then click Advanced display settings. 4. Click the Monitor-2 icon. 5. Select Extend these displays for multiple displays. 6. Click the Monitor-1 icon (for the primary display, the computer display). 7. Set the resolution for the primary display. 8.
1. Open Control Panel. 2. Click Hardware and Sound. 3. Click Sound. 4. Click the Recording tab in the Sound window. 5. Select Microphone, and click the Properties button. 6. Click the Levels tab, and move the Microphone Boost slider upwards. 7. Click OK. Note: For details about controlling volume, refer to your Windows online help. • Problem: A volume or balance slider cannot be moved. Solution: The slider might be grayed out. This means that its position is fixed by the hardware and cannot be changed.
Fingerprint reader problems • Problem: The surface of the reader is dirty, stained, or wet. Solution: Gently clean the surface of the reader with a dry, soft, lint-free cloth. • Problem: The reader often fails to enroll or authenticate your fingerprint. Solution: If the surface of the reader is dirty, stained, or wet, gently clean the surface of the reader with a dry, soft, lint-free cloth. For tips on how to maintain the fingerprint reader, refer to Maintaining the fingerprint reader.
3. Reinstall the battery and reconnect the ac power adapter, then turn on the computer. 4. If the power adapter icon still is not displayed in the Windows notification area and the system-status indicator does not blink three times when an ac power source is connected, have the ac power adapter and your computer serviced. Note: If you are using the Windows 7 operating system, to display the power adapter (power plug) icon, click Show hidden icons in the Windows notification area.
If you receive an error message while the operating system is loading the desktop configuration after the POST is completed, check the following items: 1. Go to the Lenovo Support Web site at http://www.lenovo.com/support and search for the error message. 2. Go to the Microsoft Knowledge Base homepage at http://support.microsoft.com/ and search for the error message. Sleep and hibernation problems • Problem: The computer enters sleep mode unexpectedly.
If your computer tries to enter sleep mode but the request is rejected, the device attached to the USB connector might have been disabled. If this occurs, do a hot-unplug-and-plug operation for the USB device. • Problem: The battery discharges slightly while the computer is in hibernation mode. Solution: If the wakeup function is enabled, the computer consumes a small amount of power. This is not a defect. For details, refer to “Power-saving modes” on page 31.
• Problem: The tray does not open even if you press the eject button. Solution: When your computer is not turned on, pressing the eject button does not cause the drive tray to open. Make sure that the computer is turned on and that the drive connector is firmly connected to the computer. If the tray still does not open, make sure that the computer is running, and insert the end of a straightened paper clip into the emergency eject hole. The tray will open.
Problems with ports and connectors The following are the most common problems with ports and connectors. A USB problem Problem: A device connected to the USB connector does not work. Solution: Open the Device Manager window. Make sure that the USB device setup is correct, and that the assignment of computer resource and the installation of the device driver are correct. To open the Device Manager window, go to Control Panel and click Hardware and Sound ➙ Device Manager.
102 User Guide
Chapter 9. Recovery overview This chapter provides information about the recovery solutions provided by Lenovo. • “Recovery overview for the Windows 7 operating system” on page 103 • “Recovery overview for the Windows 8.1 operating system” on page 108 • “Recovery overview for the Windows 10 operating system” on page 111 Recovery overview for the Windows 7 operating system This section provides information about the recovery solutions provided by Lenovo on the Windows 7 operating system.
To create recovery media, click Start ➙ All Programs ➙ Lenovo PC Experience ➙ Lenovo Tools ➙ Factory Recovery Disks. Then, follow the instructions on the screen. Using recovery media This section provides instructions on how to use recovery media on different operating systems. • You can use recovery media to restore the computer to the factory default settings only. You can use recovery media to put the computer in an operational state after all other methods of recovery have failed.
3. Click Back up your hard drive and select backup operation options. Then, follow the instructions on the screen to complete the backup operation. Performing a recovery operation This section provides instructions on how to perform a recovery operation using the Rescue and Recovery program. 1. From the Windows desktop, click Start ➙ All Programs ➙ Lenovo PC Experience ➙ Lenovo Tools ➙ Enhanced Backup and Restore. The Rescue and Recovery program opens. 2.
3. If you have set a Rescue and Recovery password, type your password when prompted. The Rescue and Recovery workspace opens after a short delay. Note: If the Rescue and Recovery workspace fails to open, see “Solving recovery problems” on page 108. 4. Do one of the following: • To rescue files from your hard disk drive or hybrid drive from a backup, click Rescue files and follow the instructions on the screen.
2. Repeatedly press and release the F12 key when turning on the computer. When the Boot Menu window opens, release the F12 key. 3. In the Boot Menu window, select the desired optical drive as the first boot device. Then, insert the rescue disc into the optical drive and press Enter. The rescue medium starts. • If you have created a rescue medium using a USB hard disk drive, use the following instructions to use the rescue medium: 1.
• In the subfolder for the device, look for the executable file (a file with the extension .exe). Double-click the file, and follow the instructions on the screen. Attention: If you need updated device drivers for your computer, do not download them from the Windows Update Web site. Obtain them from Lenovo. For more information, see “Making sure device drivers are current” on page 78.
Resetting your computer to the factory default settings If you want to recycle your computer or just start over, you can reset your computer to the factory default settings. Resetting the computer will reinstall the operating system, reinstall all the programs that came with your computer, and reset all the settings to the factory default settings. Attention: If you reset the computer to the factory default settings, all your personal files and settings will be deleted.
Creating recovery media To create recovery media, you need a USB drive with at least 16 GB of storage. The required USB capacity depends on the size of the recovery image. Attention: Creating recovery media will delete anything stored on the USB drive. To avoid data loss, make a backup copy of all the data that you want to keep. To create recovery media, do the following: Note: Ensure that your computer is connected to ac power. 1.
Recovery overview for the Windows 10 operating system The Windows recovery programs enable you to reset your computer or use advanced startup options. It is recommended that you create a recovery USB drive as early as possible. Store the recovery USB drive as a backup or replacement for the Windows recovery programs. For more information, see “Creating and using a recovery USB drive” on page 111. Resetting your computer If your computer does not perform well, you might consider resetting your computer.
Creating a recovery USB drive The USB drive that you use to create the recovery USB drive must be at least 16 GB of storage. The actual USB capacity that is required depends on the size of the recovery image. Attention: The creation process deletes anything stored on the USB drive. To avoid data loss, make a backup copy of all the data that you want to keep. To create a recovery USB drive, do the following: Note: Ensure that your computer is connected to ac power during the following process. 1.
Chapter 10. Replacing devices This chapter provides instructions on how to install or replace hardware for your computer.
DANGER If the rechargeable battery is incorrectly replaced, there is danger of an explosion. The battery contains a small amount of harmful substances. To avoid possible injury: • Replace only with a battery of the type recommended by Lenovo. • Keep the battery away from fire. • Do not expose it to excessive heat. • Do not expose it to water or rain. • Do not short-circuit it. • Do not drop, crush, puncture the battery, or make it subject to strong forces.
4. Insert a new battery until it clicks into place 1 . Slide the battery latch to the locked position 2 . 5. Turn the computer over again. Connect the ac power adapter and all cables. Replacing the keyboard Before you start, print these instructions and read “Important safety information” on page vi. DANGER During electrical storms, do not perform any replacement and do not connect or disconnect the telephone cable from the telephone outlet on the wall.
4. Loosen the screws 1 and then remove the cover 2 . 5. Remove the screws that secure the keyboard. 6. Turn the computer over and open the display.
7. Push hard in the direction shown by the arrows to unlatch the front side of the keyboard. 8. Detach the keyboard from the keyboard frame. Chapter 10.
9. Detach the connectors to remove the keyboard. Installing the keyboard To install the keyboard, do the following: 1. Attach the connectors.
2. Insert the keyboard. Ensure that the rear edge of the keyboard is under the frame. 3. Slide the keyboard into place in the direction shown by the arrows. Chapter 10.
4. Reinstall the screws. 5. Reinstall the computer cover 1 . Then tighten the screws 2 . 6. Reinstall the battery. See “Replacing the battery” on page 113. 7. Turn the computer over again. Connect the ac power adapter and all cables. Replacing the storage drive Before you start, print these instructions and read “Important safety information” on page vi. Attention: The storage drive is very sensitive. Incorrect handling can cause damage and permanent loss of data.
• Do not apply pressure to the cover of the drive. • Do not touch the connector. • Before removing the storage drive, make a backup copy of all the information on it and then turn off the computer. • Never remove the drive while the computer is operating, in sleep mode, or in hibernation mode. To replace the storage drive, do the following: 1. Turn off the computer; then disconnect the ac power adapter and all cables from the computer. Wait several minutes to let the computer cool. 2.
6. Lift the tab to remove the storage drive out of the computer. 7. Place the new storage drive into the drive bay.
8. Slide the storage drive firmly into the bay until it is firmly connected 1 , and then reinstall the screws 2 . 9. Reinstall the computer cover 1 . Then tighten the screws 2 . 10. Reinstall the battery. See “Replacing the battery” on page 113. 11. Turn the computer over again. Connect the ac power adapter and all cables. Replacing the optical drive Before you start, print these instructions and read “Important safety information” on page vi. You computer is shipped with an optical drive installed.
3. Close the computer display and turn the computer over. 4. Loosen the screws 1 and then remove the cover 2 . 5. Remove the screw that secures the optical drive. 6. Pull out the optical drive.
7. Insert the new optical drive into the optical-drive bay, and then press it firmly into the connector. 8. Reinstall the screw to secure the optical drive. 9. Reinstall the computer cover 1 . Then tighten the screws 2 . 10. Reinstall the battery. See “Replacing the battery” on page 113. 11. Turn the computer over again. Connect the ac power adapter and all cables. Chapter 10.
Replacing a memory module Before you start, print these instructions and read “Important safety information” on page vi. Increasing memory capacity is an effective way to make programs run faster. To replace or add a memory module, ensure you follow the notices and instructions in this topic. Note: The operating speed of a memory module has dependency on the system configuration. In some conditions, the memory module in your computer might not be able to operate at the maximum speed.
5. Open the latches on both sides of the memory slot at the same time 1 and then remove the memory module 2 . 6. Place the notched end of the new memory module toward the contact edge side of the memory slot. Insert the memory module 1 into the slot at an angle of about 20 degrees. Pivot the memory module downward until it snaps into place 2 . Ensure that the memory module is firmly installed in the slot and cannot be moved easily. Attention: Do not touch the contact edge of the memory module.
7. Reinstall the computer cover 1 . Then tighten the screws 2 . 8. Reinstall the battery. See “Replacing the battery” on page 113. 9. Turn the computer over again. Connect the ac power adapter and all cables. Replacing the coin-cell battery Before you start, print these instructions and read “Important safety information” on page vi. Prerequisites for the procedure DANGER If the coin-cell battery is incorrectly replaced, there is danger of an explosion.
4. Loosen the screws 1 and then remove the cover 2 . 5. Detach the connector 1 . Then remove the coin-cell battery 2 . 6. Install the new coin-cell battery 1 . Then attach the connector 2 . Chapter 10.
7. Reinstall the computer cover 1 . Then tighten the screws 2 . 8. Reinstall the battery. See “Replacing the battery” on page 113. 9. Turn the computer over again. Connect the ac power adapter and all cables.
Chapter 11. Getting support This chapter provides information about getting help and support from Lenovo. • “Before you contact Lenovo” on page 131 • “Getting help and service” on page 131 • “Purchasing additional services” on page 133 Before you contact Lenovo Often, you can solve your computer problems by referring to the information in the explanations of error codes, running diagnostic programs, or by consulting the Lenovo Web site. Registering your computer Register your computer with Lenovo.
Information about your computer and preinstalled software, if any, is available in the documentation that comes with your computer. The documentation includes printed books, online books, readme files, and help files. In addition, information about Lenovo products is available on the World Wide Web. Microsoft Service Packs are the latest software source for Windows product updates. They are available through Web download (connection charges might apply) or through disc.
• • • • • • Replacement or use of parts not manufactured for or by Lenovo or nonwarranted parts Identification of software problem sources Configuration of UEFI BIOS as part of an installation or upgrade Changes, modifications, or upgrades to device drivers Installation and maintenance of network operating systems (NOS) Installation and maintenance of application programs For the terms and conditions of the Lenovo Limited Warranty that applies to your Lenovo hardware product, see “Warranty information” in
134 User Guide
Appendix A. Regulatory information Location of the UltraConnect wireless antennas ThinkPad notebook computers feature an integrated UltraConnect™ wireless antenna system built into the display for optimal reception, enabling wireless communication wherever you are.
• A/V Remote Control Profile (AVRCP) • Basic Imaging Profile (BIP) • Basic Printing Profile (BPP) • Dial-Up Networking Profile (DUN) • File Transfer Profile (FTP) • Generic Access Profile (GAP) • Generic A/V Distribution Profile (GAVDP) • Hardcopy Cable Replacement Profile (HCRP) • Headset Profile (HSP) • Hands-Free Profile (HFP) • Human Interface Device Profile (HID) • Message Access Profile (MAP) • Object Exchange Protocol (OBEX) • Object Push Profile (OPP) • Personal Area Networking Profile (PAN) • Phone
If you are uncertain of the policy that applies to the use of wireless devices in a specific organization (such as airport or hospital), you are encouraged to ask for authorization to use integrated wireless cards prior to turning on the computer. Wireless-radio compliance information Computer models equipped with wireless communications comply with the radio frequency and safety standards of any country or region in which it has been approved for wireless use.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
German Class B compliance statement Deutschsprachiger EU Hinweis: Hinweis für Geräte der Klasse B EU-Richtlinie zur Elektromagnetischen Verträglichkeit Dieses Produkt entspricht den Schutzanforderungen der EU-Richtlinie 2004/108/EG (früher 89/336/EWG) zur Angleichung der Rechtsvorschriften über die elektromagnetische Verträglichkeit in den EU-Mitgliedsstaaten und hält die Grenzwerte der EN 55022 Klasse B ein.
Japan VCCI Class B compliance statement Japan compliance statement for products which connect to the power mains with rated current less than or equal to 20 A per phase Japan notice for ac power cord The ac power cord shipped with your product can be used only for this specific product. Do not use the ac power cord for other devices.
Appendix B. WEEE and recycling statements Lenovo encourages owners of information technology equipment to responsibly recycle their equipment when it is no longer needed. Lenovo offers a variety of programs and services to assist equipment owners in recycling their IT products. Information on product recycling offerings can be found on Lenovo's Internet site at http://www.lenovo.com/social_responsibility/us/en/.
for Promotion of Effective Utilization of Resources, Lenovo Japan provides, through its PC Collecting and Recycling Services, for the collecting, reuse, and recycling of disused computers and monitors. For details, visit the Lenovo Web site at http://www.lenovo.com/recycling/japan. Pursuant to the Law for Promotion of Effective Utilization of Resources, the collecting and recycling of home-used computers and monitors by the manufacturer was begun on October 1, 2003.
Battery recycling information for Taiwan Battery recycling information for the European Union Notice: This mark applies only to countries within the European Union (EU). Batteries or packaging for batteries are labeled in accordance with European Directive 2006/66/EC concerning batteries and accumulators and waste batteries and accumulators. The Directive determines the framework for the return and recycling of used batteries and accumulators as applicable throughout the European Union.
144 User Guide
Appendix C. Restriction of Hazardous Substances Directive (RoHS) European Union RoHS Lenovo products sold in the European Union, on or after 3 January 2013 meet the requirements of Directive 2011/65/EU on the restriction of the use of certain hazardous substances in electrical and electronic equipment (“RoHS recast” or “RoHS 2”). For more information about Lenovo progress on RoHS, go to: http://www.lenovo.com/social_responsibility/us/en/RoHS_Communication.
China RoHS India RoHS RoHS compliant as per E-Waste (Management & Handling) Rules, 2011.
Turkish RoHS The Lenovo product meets the requirements of the Republic of Turkey Directive on the Restriction of the Use of Certain Hazardous Substances in Waste Electrical and Electronic Equipment (WEEE). Ukraine RoHS Appendix C.
148 User Guide
Appendix D. ENERGY STAR model information ENERGY STAR® is a joint program of the U.S. Environmental Protection Agency and the U.S. Department of Energy aimed at saving money and protecting the environment through energy efficient products and practices. Lenovo is proud to offer our customers products with the ENERGY STAR qualified designation. You might find an ENERGY STAR mark affixed on the computer or displayed on the power settings interface.
5. Clear the Allow this device to wake the computer check box. 6. Click OK.
Appendix E. Trademarks The following terms are trademarks of Lenovo in the United States, other countries, or both: Lenovo Access Connections Active Protection System Secure Data Disposal ThinkPad ThinkPad logo TrackPoint UltraConnect Intel and Intel SpeedStep are trademarks of Intel Corporation in the U. S. and/or other countries. Microsoft, Windows, Direct3D, BitLocker, and Cortana are trademarks of the Microsoft group of companies.
152 User Guide
Appendix F. Notices Lenovo may not offer the products, services, or features discussed in this document in all countries. Consult your local Lenovo representative for information on the products and services currently available in your area. Any reference to a Lenovo product, program, or service is not intended to state or imply that only that Lenovo product, program, or service may be used.
154 User Guide
