Guide d'utilisation ThinkPad T540p, W540 et W541
Remarque : Avant d'utiliser le présent document et le produit associé, prenez connaissance des informations suivantes : • Consignes de sécurité, Déclaration de garantie et Guide de configuration • Regulatory Notice • « Consignes de sécurité » à la page vi • Annexe E « Remarques » à la page 189 Les versions les plus récentes du manuel Consignes de sécurité, Déclaration de garantie et Guide de configuration et du document Regulatory Notice sont disponibles sur le site Web du support Lenovo® à l'adresse suiv
Table des matières A lire en premier . . . . . . . . . . . . v Consignes de sécurité. . . . . . . . . . . . Conditions nécessitant une intervention immédiate. . . . . . . . . . . . . . . Maintenance et mises à niveau . . . . . . Cordons et boîtiers d'alimentation . . . . . Prolongateurs et dispositifs connexes . . . . Fiches électriques et prises de courants . . . Boîtier d'alimentation . . . . . . . . . . Périphériques externes. . . . . . . . . . Remarque générale sur la batterie . . . . .
Chapitre 4. Sécurité . . . . . . . . . . 55 Utilisation des mots de passe . . . . . . . . . Saisie de mots de passe . . . . . . . . . Mot de passe à la mise sous tension . . . . Mot de passe superviseur . . . . . . . . Mots de passe d'accès au disque dur. . . . Sécurité du disque dur . . . . . . . . . . . Configuration du processeur de sécurité . . . . Utilisation du lecteur d'empreintes digitales . . . Consignes de suppression de données du disque dur ou de l'unité SSD . . . . . . . . . . . .
Chapitre 10. Résolution des incidents informatiques . . . . . . . . . . . . 149 Diagnostic des incidents . . . . . . . . . . Identification et résolution des incidents. . . . Absence de réaction de l'ordinateur . . . Liquide renversé sur le clavier . . . . . . Messages d'erreur . . . . . . . . . . Erreurs sans messages . . . . . . . . Signaux sonores en cas d'erreur . . . . . Incidents liés au module de mémoire . . . Incidents liés à l'utilisation en réseau . . .
iv Guide d'utilisation
A lire en premier Veillez à respecter les conseils suivants afin de tirer le meilleur parti de votre ordinateur. En cas de non respect de ces conseils, vous vous exposez à des risques de blessure ou de gêne, ou entraîner un dysfonctionnement de votre ordinateur. Protégez-vous contre la chaleur que dégage votre ordinateur. Lorsque l'ordinateur est sous tension ou que la batterie est en charge, la base, le repose-mains et certaines autres parties peuvent chauffer.
Protégez votre ordinateur et vos données lors de vos déplacements. Avant de déplacer un ordinateur doté d'une unité de disque dur, procédez de l'une des manières suivantes et assurez-vous que l'interrupteur d'alimentation est éteint ou clignote : • Mettez l'ordinateur hors tension. • Mettez-le en mode veille. • Mettez-le en mode hibernation. Cela permet d'éviter toute détérioration de l'ordinateur et toute perte de données. Manipulez votre ordinateur avec précaution.
outre, les ordinateurs peuvent contenir une pile interne de la taille d'une pièce de monnaie qui alimente l'horloge système même lorsque l'ordinateur est débranché. Les consignes de sécurité concernant les piles s'appliquent donc à tous les ordinateurs. Conditions nécessitant une intervention immédiate Un produit peut être endommagé en raison d'une mauvaise utilisation ou d'une négligence.
Remarque : Certains composants de l'ordinateur peuvent être mis à niveau ou remplacés par le client. Les mises à niveau sont généralement appelées des options. Les composants de rechange dont l'installation par le client est approuvée sont appelés des unités remplaçables par l'utilisateur, ou CRU. Lenovo fournit une documentation qui contient des instructions indiquant dans quels cas le client peut installer des options ou remplacer des CRU.
Branchez toujours les cordons d'alimentation et les câbles d'interface dans le bon ordre et assurez-vous que tous leurs connecteurs sont bien enfoncés et fixés dans les prises. N'utilisez pas de boîtiers d'alimentation présentant des signes de corrosion sur les broches d'entrée C.A. ou des signes de surchauffe (déformation du plastique, par exemple) sur les broches d'entrée C.A. ou à tout autre endroit.
Boîtier d'alimentation DANGER Ne retirez jamais le cache d’un bloc d’alimentation ou d’un autre composant portant l’étiquette suivante. Les composants portant cette étiquette contiennent une tension, un courant électrique et des niveaux d’énergie dangereux. Aucune pièce ne peut être remplacée à l’intérieur de ces composants. Si vous pensez qu’un de ces composants présente un problème, contactez un technicien de maintenance.
Consigne relative à la batterie rechargeable DANGER Ne tentez pas de démonter le bloc de batteries. Cela pourrait entraîner une explosion ou une fuite de liquide de la . Une autre que celle spécifiée par Lenovo ou une unité démontée ou modifiée n'est pas couverte par la garantie. Si le bloc de batteries rechargeables n'est pas correctement placé, il existe un risque d'explosion. Le bloc de batteries contient, en petite quantité, des substances toxiques.
Produits à base de perchlorate - des consignes de manipulation spéciales peuvent s'appliquer. Voir www.dtsc.ca.gov/hazardouswaste/perchlorate Chaleur et ventilation des produits DANGER Les ordinateurs, adaptateurs secteur et de nombreux accessoires peuvent générer de la chaleur lorsqu'ils sont sous tension et lorsque les batteries sont en charge. Les ordinateurs portables peuvent émettre une quantité importante de chaleur en raison de leur taille compacte.
Courant électrique DANGER Le courant électrique provenant de l'alimentation, du téléphone et des câbles de transmission peut présenter un danger. Pour éviter tout risque de choc électrique : • Evitez d'utiliser votre ordinateur pendant un orage. • Ne manipulez aucun câble et n'effectuez aucune opération d'installation, d'entretien ou de reconfiguration de ce produit au cours d'un orage. • Branchez tous les cordons d'alimentation sur un socle de prise de courant correctement câblé et mis à la terre.
Conformité aux normes relatives aux appareils à laser ATTENTION : Si des produits laser (tels que des unités de CD, DVD, à fibre optique ou des émetteurs) sont installés, lisez les informations suivantes : • Ne retirez pas les carters. En ouvrant le produit laser, vous vous exposez au rayonnement dangereux du laser. Aucune pièce de l'unité n'est réparable.
Si votre ordinateur Lenovo est livré avec un casque ou des écouteurs, l'association de ces dispositifs à l'ordinateur respecte les spécifications de la norme NF EN 50332-1. Si vous utilisez d'autres casques ou écouteurs, assurez-vous qu'ils sont conformes aux spécifications de la norme NF EN 50332-1 (clause 6.5 relative aux valeurs de limitation).
xvi Guide d'utilisation
Chapitre 1. Présentation du produit Ce chapitre fournit des informations sur les emplacements des connecteurs, les étiquettes importantes relatives au produit, les fonctions de l'ordinateur, les caractéristiques, l'environnement d'exploitation et les programmes préinstallés.
Figure 2. Vue avant du ThinkPad W541 1 1 Caméra (sur certains modèles) 6 Détecteur de couleurs (sur certains modèles) 2 Microphones 7 Dispositif de pointage TrackPoint® 3 Interrupteur d'alimentation 8 Logo NFC (sur certains modèles) 4 Pavé numérique 9 Pavé tactile ThinkPad® 5 Lecteur d'empreintes digitales (sur certains modèles) 10 Boutons TrackPoint Caméra (sur certains modèles) La caméra vous permet de prendre des photos ou de tenir une vidéo conférence.
1. Allez sur le Panneau de configuration, puis modifiez l'affichage du Panneau de configuration de Catégorie à Grandes icônes ou Petites icônes. 2. Cliquez sur Options d'alimentation ➙ Choisir l'action des boutons d'alimentation. 3. Suivez les instructions qui s'affichent à l'écran. 4 Pavé numérique Utilisez le pavé numérique pour saisir des chiffres rapidement.
1 Logement pour carte à puce (sur certains modèles) 4 Connecteur USB 2.0 2 Baie Serial Ultrabay™ Enhanced 5 Prise de sécurité 3 Connecteur USB 3.0 1 Logement pour carte à puce (sur certains modèles) Votre ordinateur peut être équipé d'un logement pour carte à puce. Pour plus d'informations, voir « Utilisation d'une carte ExpressCard, d'une carte Flash Media Card ou d'une carte à puce » à la page 46.
Vue du côté gauche Figure 4. Vue du côté gauche 1 Grilles de ventilation (gauche) 5 Connecteur USB 3.0 2 Mini-connecteur ou connecteur Thunderbolt™ (en fonction du modèle) DisplayPort® 1 6 Logement pour carte ExpressCard (sur certains modèles) 3 Connecteur VGA 7 Logement pour carte mémoire 4 Connecteur Always-On USB 2.
Remarque : Si vous connectez l'ordinateur à une station d'accueil, utilisez le connecteur VGA de la station d'accueil, et non pas celui de l'ordinateur. Pour plus d'informations, voir « Connexion d'un écran externe » à la page 42. 4 Connecteur Always-On USB 2.0 Par défaut, le connecteur Always-on USB 2.0 vous permet de charger certains appareils numériques mobiles et des smartphones dans les situations suivantes : • Lorsque votre ordinateur est allumé ou en mode veille.
Vue de dessous Figure 5. Vue de dessous 1 Bloc de batteries 4 Trous de drainage du clavier 2 Logement pour carte SIM 5 Haut-parleurs 3 Connecteur de la station d'accueil 1 Bloc de batteries Utilisez l'ordinateur en mode d'alimentation sur batterie lorsque vous ne disposez pas d'une alimentation électrique. Vous pouvez utiliser le programme Power Manager pour ajuster les paramètres d'alimentation en fonction de vos besoins.
Vue arrière Figure 6. Vue arrière 1 Port Ethernet 3 Grilles de ventilation (arrière) 2 Connecteur d'alimentation 1 Port Ethernet Connectez l'ordinateur à un réseau local (LAN) à l'aide du connecteur Ethernet. DANGER Pour éviter tout risque d'électrocution, ne branchez pas le câble téléphonique sur le connecteur Ethernet. Vous ne pouvez brancher qu'un câble Ethernet sur ce connecteur. Le connecteur Ethernet a deux voyants qui indiquent l'état de la connexion au réseau.
1 Voyant de la touche Fn Lock Le voyant de verrouillage de la touche Fn indique le statut de la fonction de verrouillage de la touche Fn. Pour plus d'informations, voir « Touches spéciales » à la page 22. 2 Voyant de coupure du haut-parleur Lorsque le voyant de coupure du haut-parleur est allumé, cela signifie que les haut-parleurs sont coupés. 3 Voyant de coupure du micro Lorsque le voyant de coupure du micro est allumé, cela signifie que les micros sont coupés.
• Clignotement lent : l'ordinateur est en mode veille. 6 Voyant du détecteur de couleur Lorsque le détecteur de couleur est opérationnel, le voyant du Logo ThinkPad situé sur le couvercle extérieur de votre ordinateur fonctionne en clignotant deux fois à des intervalles réguliers.
Les étiquettes d'identification FCC et du numéro de certification IC sont apposées sur les cartes réseau local sans fil 1 et réseau étendu sans fil 2 installées dans l'ordinateur. Pour retirer la carte réseau local sans fil en vue de la réparer ou pour la remplacer, voir « Remplacement de la carte réseau local sans fil » à la page 92. Pour savoir comment retirer la carte réseau étendu sans fil en vue de la réparer ou pour la remplacer, voir « Remplacement de la carte réseau étendu sans fil » à la page 96.
Étiquette produit authentique Microsoft Windows 8, Windows 8.1 et Windows 10 : selon votre emplacement géographique, la date de fabrication de votre ordinateur et la version de Windows 8, Windows 8.1 ou Windows 10 qui y est préinstallée, une étiquette produit authentique Microsoft peut être apposée sur le carter de l'ordinateur. Consultez la page http://www.microsoft.com/en-us/howtotell/Hardware.aspx pour voir des images des différents types d'étiquette produit authentique Microsoft.
• Unité SSD 2,5 pouces (hauteur 7 mm) à faible encombrement • Unité SSD M.2 pour cache uniquement (sur certains modèles) Display L'écran couleur utilise la technologie Thin Film Transistor (TFT).
Dispositifs de sécurité • Lecteur d'empreintes digitales (sur certains modèles) Spécifications La présente section répertorie les spécifications physiques de votre ordinateur.
Attention : • Tenez les appareils électriques tels que les ventilateurs, radios, climatiseurs et fours micro-ondes à l'écart de l'ordinateur. Les puissants champs magnétiques générés par ces appareils risqueraient d'endommager le moteur de l'unité de disque dur et les données qu'elle contient. • Ne posez pas de boissons sur ou à côté de l'ordinateur ou d'autres périphériques connectés.
Access Connections™ (Windows 7) Le programme Access Connections est un assistant de connectivité permettant de créer et de gérer les profils emplacement. Chaque profil d'emplacement stocke tous les paramètres de la configuration Internet et du réseau requis pour se connecter à partir d'une infrastructure réseau située dans un lieu tel que le domicile ou le bureau.
Lenovo Settings (Windows 8, Windows 8.1 et Windows 10) Lenovo Solution Center (Windows 7, Windows 8, Windows 8.1 et Windows 10) Mobile Broadband Connect (Windows 7 et Windows 10) Message Center Plus (Windows 7) Password Manager (Windows 7, Windows 8 et Windows 8.1) Power Manager (Windows 7) REACHit (Windows 7, Windows 8, Windows 8.1 et Windows 10) Recovery Media Le programme Lenovo Settings vous permet d'optimiser l'utilisation de votre ordinateur.
18 Guide d'utilisation
Chapitre 2. Utilisation de votre ordinateur Le présent chapitre explique comment utiliser certains des composants de l'ordinateur.
Pour tirer le meilleur parti de votre ordinateur, consultez la page Web suivante pour obtenir des informations sur l'identification des incidents ainsi que des réponses aux questions courantes : http://www.lenovo.com/support/faq Puis-je obtenir mon guide d'utilisation dans une autre langue ? • Pour télécharger le guide d'utilisation dans une autre langue, accédez au site suivant : http://www.lenovo.com/support. Suivez ensuite les instructions qui s'affichent à l'écran.
Comment brancher ou remplacer un périphérique ? • Pour plus d'informations sur le remplacement de périphériques de votre ordinateur, reportez-vous à la section Chapitre 6 « Remplacement de périphériques » à la page 81. Cela fait déjà un certain temps que j'utilise mon ordinateur et celui-ci présente des signes de ralentissement. Que dois-je faire ? • Suivez les « Conseils généraux pour la prévention des incidents » à la page 143.
• Sous Windows 10 : ouvrez le menu Démarrer et cliquez sur Commencer dans le volet de droite. En outre, vous pouvez effectuer une recherche à partir de la barre des tâches pour trouver de l'aide, des applications, des fichiers, des paramètres, etc. Touches spéciales Le clavier dispose de plusieurs touches spéciales, notamment la touche Fn 1 et les touches de fonction 2 .
4 Touches de fonction Vous pouvez configurer la touche Fn et les touches de fonction dans la fenêtre Propriétés du clavier en procédant comme suit : 1. Allez sur le Panneau de configuration, puis modifiez l'affichage du Panneau de configuration de Catégorie à Grandes icônes ou Petites icônes. 2. Cliquez sur Clavier. Dans la fenêtre Propriétés du clavier, cliquez sur l'onglet Touches de fonction et Fn ou sur Touches F1-F12 ThinkPad. 3. Sélectionnez les options qui vous conviennent.
• • : affiche les programmes que vous avez ouverts. : Sous Windows 8, Windows 8.1 et Windows 10 : affiche tous les programmes. Sous Windows 7 : ouvre Ordinateur. • Fn+Barre d'espacement : contrôle le rétro-éclairage du clavier. Les trois modes disponibles pour le rétro-éclairage du clavier sont les suivants : Désactivé, Faible et Elevé. Appuyez sur Fn+Barre d'espacement pour modifier les modes de rétro-éclairage du clavier. • Fn+B : a la même fonction que la touche Attn.
• « Dispositif de pointage ThinkPad sans les boutons TrackPoint » à la page 28 Dispositif de pointage ThinkPad avec les boutons TrackPoint Ce type de dispositif de pointage ThinkPad est constitué des composants suivants : 1 2 Dispositif de pointage TrackPoint Pavé tactile Par défaut, le dispositif de pointage TrackPoint et le pavé tactile sont activés, tout comme les fonctions tactiles. Pour modifier les paramètres, voir « Personnalisation du dispositif de pointage ThinkPad » à la page 32.
Le dispositif de pointage TrackPoint comprend le dispositif de pointage TrackPoint et plusieurs boutons TrackPoint : 1 2 Dispositif de pointage TrackPoint Bouton clic gauche (bouton clic principal) 3 Bouton clic droit (bouton clic secondaire) 4 Barre de défilement Pour utiliser le dispositif de pointage TrackPoint, procédez comme suit : Remarque : Placez vos mains en position de frappe et appuyez doucement avec l'index ou le majeur sur le capuchon antidérapant du dispositif de pointage.
Le pavé tactile peut être divisé en deux zones : 1 2 Zone de clic gauche (zone de clic principal) Zone de clic droit (zone de clic secondaire) Pour utiliser le pavé tactile, procédez comme suit : • Pointer Faites glisser un doigt sur la surface du pavé tactile pour déplacer le pointeur en conséquence. • Clic gauche Appuyez sur la zone de clic gauche 1 pour sélectionner ou ouvrir un élément.
Dispositif de pointage ThinkPad sans les boutons TrackPoint Ce type de dispositif de pointage ThinkPad est constitué des composants suivants : 1 2 Bouton de pointage Pavé tactile En fonction de vos préférences, vous pouvez utiliser le dispositif de pointage dans l'un des modes suivants : • Mode TrackPoint • Mode Pavé tactile • Mode TrackPoint classique Pour modifier le mode du dispositif de pointage, voir « Personnalisation du dispositif de pointage ThinkPad » à la page 32.
1 Pointer Utilisez le bouton de pointage pour déplacer le pointeur sur l'écran. Pour utiliser le bouton de pointage, appuyez sur son capuchon antidérapant dans la direction souhaitée, parallèlement au clavier. Le pointeur se déplace en conséquence, mais le bouton de déplacement ne bouge pas. La vitesse de déplacement du pointeur est fonction de la pression exercée sur le bouton de pointage.
1 Pointer Utilisez le bouton de pointage pour déplacer le pointeur. Pour utiliser le bouton de pointage, appuyez sur son capuchon antidérapant dans la direction souhaitée, parallèlement au clavier. Le pointeur se déplace en conséquence, mais le bouton de déplacement ne bouge pas. La vitesse de déplacement du pointeur est fonction de la pression exercée sur le bouton de pointage.
Appuyer Appuyez n'importe où sur le pavé tactile à l'aide d'un doigt pour sélectionner ou ouvrir un élément. Appuyer à l'aide de deux doigts Appuyez n'importe où sur le pavé tactile à l'aide de deux doigts afin d'afficher un menu contextuel. Faire défiler à l'aide de deux doigts Placez deux doigts sur le pavé tactile et déplacez-les dans le sens vertical ou horizontal. Cette action vous permet de parcourir un document, un site Web ou des applications.
Balayez vers le haut à l'aide de trois doigts Placez trois doigts sur le pavé tactile et déplacez-les vers le haut pour ouvrir l'affichage par tâche et voir toutes vos fenêtres ouvertes. Balayez à l'aide de trois doigts Placez trois doigts sur le pavé tactile et déplacez-les vers le bas pour afficher le bureau. Personnalisation du dispositif de pointage ThinkPad Vous pouvez personnaliser le dispositif de pointage ThinkPad afin de pouvoir l'utiliser de façon plus conviviale et efficace.
Vérification de l'état de la batterie Déplacez votre pointeur sur l'icône d'état de la batterie dans la zone de notification Windows afin de vérifier l'état de la batterie. L'icône d'état de la batterie montre le pourcentage d'énergie restant dans la batterie et indique la durée pendant laquelle vous pouvez utiliser votre ordinateur avant de devoir recharger la batterie.
Chargement de la batterie Lorsque vous constatez que le pourcentage d'énergie restante est faible, ou lorsque l'alarme d'alimentation vous avertit que la batterie est presque déchargée, vous devez recharger cette dernière ou la remplacer. Si une prise secteur est disponible, branchez-y le boîtier d'alimentation, puis connectez le boîtier d'alimentation à l'ordinateur. La batterie se recharge entièrement en 3 à 6 heures environ.
– Sous Windows 8 et Windows 8.1 : accédez à l'écran d'accueil en appuyant sur la touche Windows , cliquez sur l'icône d'alimentation puis sur Veille. – Sous Windows 10 : ouvrez le menu Démarrer, cliquez sur Alimentation puis cliquez sur Veille. • Mode hibernation Dans ce mode, vous pouvez éteindre complètement l'ordinateur sans quitter les programmes en cours d'exécution ni enregistrer les fichiers.
DANGER Ne tentez pas de démonter le bloc de batteries. Cela pourrait entraîner une explosion ou une fuite de liquide de la batterie. Une batterie autre que celle spécifiée par Lenovo, ou une batterie démontée ou modifiée ne sera pas couverte par la garantie. DANGER Si le bloc de batteries rechargeables n'est pas correctement placé, il existe un risque d'explosion. Le bloc de batteries contient, en petite quantité, des substances toxiques.
DANGER Si la batterie à pile cellulaire n'est pas correctement placée, il existe un risque d'explosion. Il existe un risque d'explosion si la batterie au lithium n'est pas correctement manipulée ou placée. Elle ne doit être remplacée que par une batterie du même type. Pour éviter tout risque de blessure ou d'accident mortel, vous ne devez pas : (1) jeter ou immerger la batterie dans l'eau, (2) exposer la batterie à une chaleur supérieure à 100 °C ou (3) tenter de réparer la batterie ou de la démonter.
Utilisation de la connexion au réseau local sans fil Un réseau local sans fil (LAN) couvre une superficie relativement restreinte. Il peut se limiter à un immeuble de bureaux ou à une maison. Les périphériques répondant à la norme 802.11 peuvent se connecter à ce type de réseau. Votre ordinateur est équipé d'une carte de réseau sans fil intégrée et d'un utilitaire de configuration permettant d'établir des connexions sans fil et à contrôler l'état de votre connexion.
Icône d'état de la connexion sans fil d'Access Connections : • La connexion radio sans fil est désactivée. • La connexion radio sans fil est activée. Pas de liaison. • La connexion radio sans fil est activée. Pas de signal. • La connexion radio sans fil est activée. Le signal de la connexion sans fil est excellent. • La connexion radio sans fil est activée. Le signal de la connexion sans fil est moyen. • La connexion radio sans fil est activée. Le signal de la connexion sans fil est faible.
Icône d'état d'Access Connections : • Aucun profil d'emplacement n'est actif ou il n'en existe pas. • Le profil d'emplacement actuel est déconnecté. • Le profil d'emplacement actuel est connecté.
Utilisation de la connexion NFC NFC est une technologie de communication sans fil haute fréquence à courte portée. En fonction du modèle, votre ordinateur peut être équipé de la fonctionnalité NFC. La fonction NFC vous permet d'établir des communications radio entre votre ordinateur et un autre périphérique compatible NFC à une distance de quelques centimètres. Par défaut, la fonction NFC est activée.
Pour plus d'informations sur l'écran externe, reportez-vous aux manuels fournis avec ce dernier. Connexion d'un écran externe Vous pouvez utiliser un écran câblé ou un écran sans fil. L'écran câblé peut être branché sur le connecteur HDMI ou VGA, ou sur le mini-connecteur DisplayPort via un câble. L'écran sans fil peut être ajouté via la fonction Wi-Di ou Miracast. • Connexion d'un écran câblé Remarque : Un câble d'interface vidéo avec cœur en ferrite est requis lorsque vous connectez un écran externe. 1.
Il existe quatre modes d'affichage : • Déconnexion : affiche la sortie vidéo uniquement sur votre écran d'ordinateur. Remarque : selon la situation, les options Déconnexion, Écran PC uniquement, Ordinateur uniquement ou Déconnecter le projecteur peuvent s'afficher. • Dupliquer : affiche la même sortie vidéo sur votre écran d'ordinateur et sur un écran externe. • Étendre : étend la sortie vidéo de votre écran d'ordinateur vers un écran externe.
• Sous Windows 10 : cliquez sur Démarrer ➙ Toutes les applications ➙ X-Rite ➙ PANTONE Color Calibrator. Lorsque le détecteur de couleur est opérationnel, le voyant du détecteur de couleur clignote deux fois à des intervalles réguliers. Lorsque la mesure du détecteur de couleur est terminée, le voyant du détecteur de couleur reste allumé. Pour localiser le voyant du détecteur de couleur, voir « Voyants d'état » à la page 8.
Configuration en vue d'un enregistrement sonore Le programme Realtek HD Audio Manager permet de configurer le micro en vue d'obtenir un enregistrement au son optimal. Pour démarrer le programme, ouvrez le Panneau de configuration, puis cliquez sur Matériel et audio ➙ Realtek HD Audio Manager. Utilisation de la caméra Si votre ordinateur est équipé d'une caméra, vous pouvez l'utiliser pour visionner votre image vidéo et pour effectuer un instantané de votre image actuelle.
Unité de DVD-ROM Une telle unité peut lire les DVD-ROM ainsi que tous les types de CD, tels que des CD-ROM, de CD-RW, des CD-R et les CD audio. Cette unité ne permet pas de procéder à des enregistrements. Graveur multisessions Une telle unité peut lire les DVD-ROM, les DVD-R, les DVD-RAM et les DVD-RW, ainsi que tous les types de CD, tels que que des CD-ROM, de CD-RW, des CD-R et les CD audio. En outre, elle permet d'enregistrer sur des DVD-R, des DVD-RW, des DVD-RAM de type II, des CD-RW et des CD-R.
• Avant de commencer à installer une carte, touchez une table en métal ou tout autre objet métallique mis à la terre. Cela permet de réduire le niveau d'électricité statique présent dans votre corps. L'électricité statique risque d'endommager la carte. • N'insérez pas une carte ExpressCard lorsque l'ordinateur est en mode veille ou hibernation, car l'ordinateur risquerait de ne pas répondre lorsque vous tenterez de l'utiliser de nouveau. Pour installer une carte, procédez comme suit : 1.
48 Guide d'utilisation
Chapitre 3. Vous et votre ordinateur Cette section fournit des informations sur l'accessibilité, le confort et vous explique comment voyager avec votre ordinateur. Accessibilité et confort De bonnes pratiques ergonomiques sont importantes pour tirer le meilleur parti de votre ordinateur personnel et éviter toute sensation d'inconfort. Agencez votre bureau et votre matériel afin de l'adapter à vos besoins personnels et au type de travail que vous effectuez.
Position des bras et des mains : gardez les avant-bras, les poignets et les mains dans une position souple (horizontale). Tapez délicatement sur les touches. Position des jambes : gardez les cuisses parallèles au sol et les pieds à plat sur le sol ou le repose-pieds. En voyage Il peut s'avérer difficile d'observer les règles d'ergonomie optimales lorsque vous utilisez l'ordinateur en dehors de votre bureau. Quel que soit l'environnement, essayez de tenir compte d'un maximum de conseils d'utilisation.
Raccourci clavier Fonction Touche du logo Windows + U Ouvrir les Options d'ergonomie Maj. droite pendant huit secondes Activer ou désactiver les touches de filtre Maj. cinq fois Activer ou désactiver les touches rémanentes Verrouillage numérique pendant cinq secondes Activer ou désactiver les touches de basculement Alt gauche + Maj. gauche + Verrouillage numérique Activer ou désactiver les touches de la souris Alt gauche + Maj.
En utilisant simplement votre voix, vous pouvez démarrer des programmes, ouvrir des menus, cliquer sur des objets à l'écran, dicter du texte dans des documents, ou encore rédiger et envoyer des e-mails. Vous pouvez effectuer oralement tout ce que vous faites habituellement à l'aide du clavier et de la souris. Pour utiliser la Reconnaissance vocale, procédez comme suit : 1. Allez sur le Panneau de configuration et vérifiez que vous visualisez ce dernier par Catégorie. 2.
4. Cliquez sur Appliquer. Ces modifications prendront effet lorsque vous vous connecterez à nouveau à votre système d'exploitation. – Modifiez la taille de tous les éléments qui se trouvent sur une page Web. Maintenez la touche Ctrl enfoncée et appuyez sur la touche plus (+) pour agrandir la taille d'un texte, ou sur la touche moins (-) pour la réduire. – Modifiez la taille de tous les éléments du bureau ou d'une fenêtre. Remarque : Cette fonction n'est pas disponible sur toutes les fenêtres.
Paramètres ➙ Réseau et Internet ➙ Mode Avion et faites glisser le curseur du mode avion vers la droite. • Faites attention au dossier qui se trouve devant vous dans l'avion. Inclinez l'écran du ThinkPad de manière à éviter qu'il ne soit percuté si la personne assise devant vous abaisse son dossier. • N'oubliez pas de mettre l'ordinateur en mode hibernation ou hors tension au décollage.
Chapitre 4. Sécurité Le présent chapitre fournit des informations sur la façon de protéger l'ordinateur contre le vol et toute utilisation non autorisée.
1. Redémarrez l'ordinateur. Lorsque le logo s'affiche à l'écran, appuyez sur F1 pour démarrer le programme ThinkPad Setup. 2. Sélectionnez Security ➙ Password ➙ Power-on Password en vous aidant des touches de déplacement. 3. En fonction de vos besoins, procédez de l'une des façons suivantes : • Pour définir un mot de passe, procédez comme suit : a. Dans la zone Enter New Password, saisissez le mot de passe de votre choix et appuyez sur Entrée. b.
– Modification des paramètres du processeur de sécurité – Effacement des données liées aux empreintes digitales – Activation ou désactivation des fonctions suivantes : – Wake on LAN et Flash over LAN – Lock UEFI BIOS Settings – Password at unattended boot – Boot Device List F12 Option – Boot Order Lock – Flash BIOS Updating by End-Users – Périphérique réseau interne – Périphérique sans fil interne – Périphérique Bluetooth interne – Réseau interne - Mémoire morte en option – Périphérique réseau étendu sans f
a. Dans la zone Enter Current Password, saisissez le mot de passe superviseur actuel et appuyez sur Entrée. b. Laissez les zones Enter New Password et Confirm New Password vides. Appuyez deux fois sur Entrée. 4. Une fenêtre Setup Notice s'affiche. Appuyez sur Entrée pour continuer. 5. Appuyez sur F10. Une fenêtre de confirmation de la configuration s'affiche. Sélectionnez Yes pour enregistrer les modifications apportées à la configuration et fermer la fenêtre.
• Si vous sélectionnez User + Master, procédez comme suit : a. Pour commencer, définissez un mot de passe utilisateur d'accès au disque dur. Lorsqu'une fenêtre de message s'affiche et vous invite à définir le mot de passe utilisateur d'accès au disque dur, appuyez sur Entrée pour continuer. Saisissez votre nouveau mot de passe utilisateur d'accès au disque dur dans la zone Enter New Password et appuyez sur la touche Entrée.
2. Saisissez le mot de passe utilisateur d'accès au disque dur actuel dans la zone Enter Current Password et appuyez sur Entrée. 3. Saisissez ensuite le nouveau mot de passe dans la zone Enter New Password et appuyez sur Entrée, puis ressaisissez-le dans la zone Confirm New Password et appuyez sur Entrée. 4. Une fenêtre Setup Notice s'affiche. Appuyez encore une fois sur Entrée pour continuer. Le mot de passe utilisateur d'accès au disque dur est alors modifié.
Utilisation de Windows BitLocker Drive Encryption Pour protéger votre ordinateur contre tout accès illicite, utilisez un logiciel de chiffrement d'unité, tel que Windows BitLocker Drive Encryption. Chiffrement de lecteur BitLocker Windows est une fonction de sécurité complète de certaines éditions du système d'exploitation Windows. Son objectif consiste à protéger le système d'exploitation et les données stockées sur votre ordinateur, même si ce dernier est perdu ou volé.
2. Sélectionnez Security ➙ Security Chip en vous aidant des touches de déplacement. 3. Appuyez sur Entrée. Le sous-menu Security Chip apparaît. 4. A l'aide des touches de déplacement, placez-vous sur l'élément à définir. Une fois l'élément mis en évidence, appuyez sur Entrée. 5. Configurez les autres éléments que vous souhaitez définir. 6. Appuyez sur F10. Une fenêtre de confirmation de la configuration s'affiche.
2. Entrez le mot de passe Windows. 3. Cliquez sur l'icône représentant le doigt que vous souhaitez enregistrer, puis faites glisser le doigt correspondant sur le lecteur d'empreintes digitales sans le relâcher jusqu'à ce que l'enregistrement soit terminé. 4. Cliquez sur Terminer. Votre empreinte digitale est bien enregistrée. Pour plus d'informations sur l'utilisation du lecteur d'empreintes digitales, reportez-vous au système d'aide du programme Fingerprint Manager Pro. • Sous Windows 10 1.
2. Faites doucement glisser votre doigt vers vous sur le lecteur en effectuant une légère pression. Ne soulevez pas votre doigt lorsque vous le faites glisser. Comportement du voyant du lecteur d'empreintes digitales Comportement du voyant Description Vert Le lecteur d'empreintes digitales est prêt à lire l'empreinte digitale. Orange L'empreinte digitale ne peut pas être authentifiée. Associez vos empreintes digitales au mot de passe à la mise sous tension et au mot de passe d'accès au disque dur.
Lorsque vous redémarrez l'ordinateur, vous pouvez utiliser vos empreintes digitales pour vous connecter, sans avoir à entrer le mot de passe Windows, le mot de passe à la mise sous tension ni le mot de passe d'accès au disque dur. Attention : Si vous utilisez toujours vos empreintes digitales pour vous connecter à l'ordinateur, vous risquez d'oublier vos mots de passe. Par conséquent, notez-les et conservez-les en lieu sûr.
• Votre doigt est rêche, sec ou blessé. • Votre doigt est sec. • Votre doigt est maculé de boue, d'huile ou de toute autre substance. • La surface de votre doigt est différente de celle figurant dans l'enregistrement de votre empreinte digitale. • Votre doigt est mouillé. • Le doigt utilisé n'a pas été enregistré. Pour résoudre le problème, effectuez l'une des opérations suivantes : • Nettoyez ou essuyez vos mains afin d'éliminer toute trace de saleté ou d'humidité.
physiquement effacées et sont conservées sur l'unité. Toutefois, elles ne peuvent pas être déchiffrées sans cette ancienne clé. Cette fonction est également disponible avec l'outil Drive Erase Utility for Resetting the Cryptographic Key and Erasing the Solid State Drive. Utilisation de pare-feu Si votre système est doté d'un pare-feu préinstallé, celui-ci protège votre ordinateur contre les menaces liées à Internet, les accès non autorisés, les intrusions et les attaques via Internet.
68 Guide d'utilisation
Chapitre 5. Présentation générale de la récupération Le présent chapitre fournit des informations sur les solutions de récupération. • • « Présentation de la récupération sous Windows 7 » à la page 69 « Présentation de la récupération sous les systèmes d'exploitation Windows 8 et Windows 8.
Remarque : Vous pouvez créer des supports de récupération à l'aide de disques ou de périphériques de stockage USB externes. Pour créer des supports de récupération, cliquez sur Démarrer ➙ Tous les programmes ➙ Lenovo PC Experience ➙ Lenovo Tools ➙ Factory Recovery Disks. Suivez ensuite les instructions qui s'affichent à l'écran. Utilisation d'un support de récupération Cette section explique comment utiliser des supports de récupération sur différents systèmes d'exploitation.
Opération de sauvegarde Cette section explique comment effectuer une opération de sauvegarde à l'aide de Rescue and Recovery. 1. Depuis le bureau Windows, cliquez sur Démarrer ➙ Tous les programmes ➙ Lenovo PC Experience ➙ Lenovo Tools ➙ Enhanced Backup and Restore. Le programme Rescue and Recovery s'ouvre. 2. Dans la fenêtre principale de Rescue and Recovery, cliquez sur la flèche Lancement de Rescue and Recovery avancé. 3.
Pour démarrer l'espace de travail Rescue and Recovery, procédez comme suit : 1. Vérifiez que l'ordinateur est hors tension. 2. Appuyez sur la touche F11 et relâchez-la plusieurs fois de suite lorsque vous mettez l'ordinateur sous tension. Lorsque vous entendez des signaux sonores ou lorsque le logo s'affiche, relâchez la touche F11. 3. Si vous avez défini un mot de passe Rescue and Recovery, tapez le mot de passe lorsque vous y êtes invité.
5. Cliquez sur OK et suivez les instructions à l'écran pour créer un support de récupération. Utilisation d'un support de récupération d'urgence La présente section explique comment utiliser le support de récupération d'urgence créé. • Si vous avez créé un support de récupération à l'aide d'un disque, procédez comme suit pour utiliser le support de récupération ; 1. Mettez votre ordinateur hors tension. 2.
3. Ouvrez le dossier DRIVERS. Le dossier contient plusieurs sous-dossiers dont les noms correspondent aux différentes unités installées sur votre ordinateur (AUDIO et VIDEO par exemple). 4. Ouvrez le sous-dossier correspondant à l'unité. 5. Réinstallez le pilote de périphérique à l'aide de l'une des méthodes suivantes : • Dans le sous-dossier du périphérique, recherchez un fichier texte (fichier ayant l'extension .txt).
Vous pouvez créer un support de récupération pour sauvegarder ou remplacer l'image de récupération Windows. Les supports de récupération vous permettent de diagnostiquer et résoudre des incidents informatiques même si vous ne pouvez pas démarrer le système d'exploitation Windows 8 ou Windows 8.1. Il est recommandé de créer le plus rapidement possible un support de récupération. Pour plus d'informations, voir « Création et utilisation d'un support de récupération » à la page 76.
• Pour effectuer un formatage rapide, cliquez sur Supprimer simplement mes fichiers pour démarrer le processus. Ce processus peut prendre quelques minutes. • Pour effectuer un formatage complet, cliquez sur Nettoyer complètement le lecteur pour démarrer le processus. Ce processus peut prendre plusieurs heures. 4. Suivez ensuite les instructions à l'écran pour réinitialiser votre ordinateur aux paramètres d'usine par défaut.
Création d'un support de récupération Pour créer un support de récupération, vous devez utiliser une unité USB avec une capacité de stockage de 8 Go minimum. La capacité de l'unité USB requise dépend de la taille de l'image de récupération. Attention : La création d'un support de récupération supprime toutes les données stockées sur l'unité USB. Afin d'éviter toute perte de données, faites une copie de sauvegarde de toutes les données que vous souhaitez conserver.
Remarque : Assurez-vous que l'ordinateur est branché sur l'alimentation secteur. 1. Mettez l'ordinateur sous tension ou redémarrez-le. Avant le démarrage du système d'exploitation Windows, appuyez à plusieurs reprises sur la touche F12. La fenêtre Boot Menu s'ouvre. 2. Définissez le lecteur de récupération en tant que périphérique d'amorçage. 3. Sélectionnez la langue de votre choix puis la disposition du clavier qui vous convient le mieux. 4.
1. Ouvrez le menu Démarrer et cliquez sur Paramètres. Si les Paramètres ne s'affichent pas, cliquez sur Toutes les applications pour afficher tous les programmes, puis sur Paramètres ➙ Mise à jour et sécurité ➙ Récupération. 2. Dans la section Démarrage avancé, cliquez sur Redémarrer maintenant ➙ Résolution des problèmes ➙ Options avancées. 3. Sélectionnez l'option de démarrage de votre choix et suivez les instructions qui s'affichent à l'écran.
Pour utiliser un lecteur de récupération USB, procédez comme suit : Remarque : Assurez-vous que l'ordinateur est branché sur l'alimentation secteur. 1. Connectez le lecteur de récupération USB à l'ordinateur. 2. Mettez l'ordinateur sous tension ou redémarrez-le. Avant le démarrage du système d'exploitation Windows, appuyez à plusieurs reprises sur la touche F12. La fenêtre Boot Menu s'ouvre. 3. Définissez le lecteur de récupération USB en tant que périphérique d'amorçage. 4.
Chapitre 6. Remplacement de périphériques Ce chapitre explique comment installer ou remplacer du matériel pour votre ordinateur.
Attention : Lenovo n'est pas responsable des performances ou de la sécurité des batteries non autorisées et ne fournit aucune garantie en cas de défaillance ou de dégâts résultant de leur utilisation. DANGER Si le bloc de batteries rechargeables n'est pas correctement placé, il existe un risque d'explosion. Le bloc de batteries contient, en petite quantité, des substances toxiques. Afin d'éviter tout accident : • Ne remplacez la batterie que par une batterie du type recommandé par Lenovo.
4. Insérez une nouvelle batterie jusqu'à ce qu'elle s'enclenche. 5. Remettez l'ordinateur à l'endroit. Branchez le boîtier d'alimentation et l'ensemble des câbles sur l'ordinateur. Installation ou remplacement de la carte SIM Avant de commencer, imprimez ces instructions. La carte SIM est une petite carte plastique identifiée par une puce à circuit intégré montée sur l'un de ses côtés.
5. Maintenez la nouvelle carte SIM avec le contact métallique vers le haut pour l'insérer dans son logement. Insérez ensuite fermement la nouvelle carte SIM dans le logement jusqu'à ce qu'elle s'enclenche. 6. Réinstallez la batterie. Voir « Remplacement de la batterie » à la page 81. 7. Remettez l'ordinateur à l'endroit. Branchez le boîtier d'alimentation et l'ensemble des câbles sur l'ordinateur. Remplacement du périphérique Ultrabay Avant de commencer, imprimez ces instructions.
5. Retirez la vis de fixation du périphérique Ultrabay. 6. Faites sortir l'unité Ultrabay pour laisser une partie exposée 1 . Si nécessaire, vous pouvez utiliser un outil, tel qu'un stylo à bille. Retirez ensuite le périphérique Ultrabay hors de l'ordinateur 2 . Chapitre 6.
7. Insérez le nouveau périphérique Ultrabay dans la baie. 8. Réinstallez la vis de fixation du périphérique Ultrabay.
9. Réinstallez le grand carter inférieur 1 2 et serrez ensuite les vis 3 . 10. Réinstallez la batterie. Voir « Remplacement de la batterie » à la page 81. 11. Remettez l'ordinateur à l'endroit. Branchez le boîtier d'alimentation et l'ensemble des câbles sur l'ordinateur. Remplacement d'un module de mémoire Avant de commencer, imprimez ces instructions. Augmenter la capacité mémoire est un moyen efficace pour accélérer l'exécution des programmes.
4. Desserrez les vis 1 , puis retirez le grand carter inférieur 2 . 5. Ouvrez simultanément les loquets situés sur les deux côtés de l'emplacement de mémoire 1 , puis retirez le module de mémoire 2 . Conservez le module de mémoire retiré pour l'utiliser ultérieurement.
6. Orientez le côté avec encoche du nouveau module de mémoire vers le côté du bord de contact de l'emplacement de mémoire, puis insérez le module de mémoire dans l'emplacement approprié en l'inclinant d'environ 20 degrés 1 . Faites pivoter le module de mémoire vers le bas jusqu'à ce qu'il s'enclenche 2 . Vérifiez que le module de mémoire est bien installé et ne peut être déplacé facilement. Attention : Ne touchez pas le bord du contact du module de mémoire.
• Remplacez l'unité de disque dur ou l'unité SSD uniquement si elle doit être réparée ou mise à niveau. Les connecteurs et le logement de l'unité de disque dur ou de l'unité SSD n'ont pas été conçus pour des remplacements ou des échanges d'unité fréquents. • Ne faites pas tomber l'unité et ne l'exposez pas à des chocs. Placez l'unité sur un tissu ou toute autre matière permettant d'absorber les chocs. • N'appuyez pas sur le cache de l'unité. • Ne touchez pas le connecteur.
5. Retirez la vis qui maintient l'unité de disque dur ou l'unité SSD. 6. Retirez l'unité de disque dur ou l'unité SSD. 7. Installez la nouvelle unité de disque dur ou l'unité SSD. Chapitre 6.
8. Réinstallez la vis pour maintenir l'unité SSD ou l'unité de disque dur. 9. Réinstallez le grand carter inférieur 1 2 et serrez ensuite les vis 3 . 10. Réinstallez la batterie. Voir « Remplacement de la batterie » à la page 81. 11. Remettez l'ordinateur à l'endroit. Branchez le boîtier d'alimentation et l'ensemble des câbles sur l'ordinateur. Remplacement de la carte réseau local sans fil Avant de commencer, imprimez ces instructions.
DANGER Le courant électrique provenant de l'alimentation, du téléphone et des câbles de transmission peut présenter un danger. Pour éviter tout risque de choc électrique, débranchez les câbles avant d'ouvrir l'obturateur de ce logement. Attention : Avant de commencer à installer une carte réseau local sans fil, touchez une table en métal ou tout autre objet métallique mis à la terre. Cela permet de réduire le niveau d'électricité statique présent dans votre corps.
6. Retirez la vis. La carte réseau local sans fil est dégagée de sa position et pivote vers le haut. 7. Retirez doucement la carte réseau local sans fil hors de son emplacement. 8. Alignez le bord de contact de la nouvelle carte réseau local sans fil avec le repère situé dans l'emplacement. Insérez ensuite doucement la nouvelle carte réseau local sans fil dans son emplacement selon un angle d'environ 20 degrés.
9. Faites pivoter la carte réseau local sans fil vers le bas 1 , puis installez la vis de fixation de la carte 2 . 10. Branchez les câbles de l'antenne sur la carte réseau local sans fil. Branchez le câble gris sur le connecteur principal sur la carte et le câble noir sur le connecteur auxiliaire sur la carte réseau local sans fil. 11. Réinstallez le petit carter inférieur 1 . Serrez ensuite la vis 2 . 12. Réinstallez la batterie. Voir « Remplacement de la batterie » à la page 81. 13.
Remplacement de la carte réseau étendu sans fil Avant de commencer, imprimez ces instructions. Conditions préalables pour remplacer ou installer la carte pour réseau étendu sans fil DANGER Pendant un orage, ne procédez à aucun remplacement ni à aucune connexion ou déconnexion du câble de la prise téléphonique murale. DANGER Le courant électrique provenant de l'alimentation, du téléphone et des câbles de transmission peut présenter un danger.
5. Si un outil est fourni avec la nouvelle carte réseau étendu sans fil pour vous permettre de déconnecter les câbles, utilisez-le pour déconnecter les câbles de la carte réseau étendu sans fil. Si aucun outil n'est fourni, maintenez le connecteur du câble avec vos doigts et déconnectez doucement chaque câble de la carte réseau étendu sans fil. 6. Retirez la vis. La carte réseau étendu sans fil est dégagée de sa position et pivote vers le haut. 7.
8. Alignez le bord de contact de la nouvelle carte réseau étendu sans fil avec le repère situé dans l'emplacement. Insérez ensuite doucement la nouvelle carte réseau étendu sans fil dans son emplacement selon un angle d'environ 20 degrés. 9. Faites pivoter la carte réseau étendu sans fil vers le bas 1 , puis installez la vis de fixation de la carte 2 . 10. Branchez les câbles de l'antenne sur la carte réseau étendu sans fil.
11. Réinstallez le petit carter inférieur 1 . Serrez ensuite la vis 2 . 12. Réinstallez la batterie. Voir « Remplacement de la batterie » à la page 81. 13. Remettez l'ordinateur à l'endroit. Branchez le boîtier d'alimentation et l'ensemble des câbles sur l'ordinateur. Remplacement de la batterie à pile cellulaire Avant de commencer, imprimez ces instructions. Conditions préalables DANGER Si la batterie à pile cellulaire n'est pas correctement remplacée, il existe un risque d'explosion.
4. Desserrez la vis 1 , puis retirez le petit carter inférieur 2 . 5. Débranchez le connecteur 1 , puis retirez la batterie à pile cellulaire 2 . 6. Installez la nouvelle batterie à pile cellulaire 1 , puis branchez le connecteur 2 .
7. Réinstallez le petit carter inférieur 1 . Serrez ensuite la vis 2 . 8. Réinstallez la batterie. Voir « Remplacement de la batterie » à la page 81. 9. Remettez l'ordinateur à l'endroit. Branchez le boîtier d'alimentation et l'ensemble des câbles sur l'ordinateur. Remplacement du clavier Avant de commencer, imprimez ces instructions. DANGER Pendant un orage, ne procédez à aucun remplacement ni à aucune connexion ou déconnexion du câble de la prise téléphonique murale.
4. Récupérez l'outil spécial clavier dans l'emballage du nouveau clavier. L'illustration suivante représente un outil spécial clavier. 5. Pour faire apparaître les têtes de vis sous le cadre du clavier, faites glisser ce dernier de 2,5 mm vers l'avant à l'aide de l'extrémité plate de l'outil spécial clavier. 6. Desserrez les vis de fixation du clavier à l'aide de l'extrémité cruciforme de l'outil spécial clavier.
7. Faites pivoter légèrement le clavier vers le haut 1 jusqu'à voir les connecteurs situés sous le clavier. Retournez ensuite le clavier 2 . 8. Placez doucement le clavier sur le repose-mains, puis débranchez les connecteurs. Retirez ensuite le clavier. Installation du nouveau clavier Pour installer le nouveau clavier, procédez comme suit : Chapitre 6.
1. Branchez les connecteurs puis retournez le clavier. 2. Insérez le clavier dans l'espace situé sous le cadre du panneau du clavier, comme indiqué ci-dessous. Assurez-vous que les bords du clavier, à l'avant, se trouvent sous le cadre du panneau du clavier.
3. Faites apparaître les têtes de vis en faisant glisser le cadre du clavier vers l'avant à l'aide de l'extrémité plate de l'outil spécial clavier. Assurez-vous que les têtes de vis sont entièrement exposées. 4. Serrez les vis de fixation du clavier à l'aide de l'extrémité cruciforme de l'outil spécial clavier. Chapitre 6.
5. Faites glisser le cadre du clavier vers l'arrière de 2,5 mm à l'aide de l'extrémité plate de l'outil spécial clavier. Placez les loquets du cadre du clavier sous le panneau du clavier en les poussant avec vos doigts comme indiqué. 6. Ajustez le cadre du clavier à l'aide de l'extrémité plate de l'outil spécial clavier, pour vous assurer que tous les loquets sont en place sous le panneau du clavier. 7. Réinstallez la batterie. Voir « Remplacement de la batterie » à la page 81. 8.
Chapitre 7. Etendre les possibilités de votre ordinateur Ce chapitre explique comment utiliser des périphériques matériels afin d'augmenter les capacités de votre ordinateur. • « Recherche d'options ThinkPad » à la page 107 • « Stations d'accueil ThinkPad » à la page 107 Recherche d'options ThinkPad Si vous voulez étendre les fonctions de votre ordinateur, Lenovo dispose d'un certain nombre d'accessoires et de mises à niveau de matériel pour satisfaire vos besoins.
ThinkPad Basic Dock Vue avant 1 Interrupteur d'alimentation : appuyez sur l'interrupteur d'alimentation pour allumer ou éteindre l'ordinateur. 2 Bouton d'éjection : appuyez sur le bouton d'éjection pour libérer l'ordinateur de la station d'accueil. 3 Adaptateur coulissant : utilisez l'adaptateur coulissant comme guide pour aligner le port de connexion de la station d'accueil sur l'ordinateur lorsque vous connectez la station d'accueil.
3 Connecteur USB 3.0 : permet de connecter des périphériques compatibles USB 3.0. 4 Connecteur Ethernet : permet de raccorder la station d'accueil à un réseau local Ethernet. Remarque : Si vous devez utiliser un connecteur Ethernet ou un connecteur d'écran externe lorsque votre ordinateur est connecté à une station d'accueil, utilisez le connecteur Ethernet ou le connecteur d'écran externe de la station d'accueil, et non pas celui de l'ordinateur.
7 Clé de verrouillage du système : permet de verrouiller le bouton d'éjection. Lorsque la clé de verrouillage du système se trouve en position verrouillée, le bouton d'éjection de la station d'accueil est verrouillé et vous ne pouvez ni connecter ni retirer l'ordinateur. Vue arrière 1 Connecteur Always-On USB : permet de connecter des périphériques compatibles USB 2.0 ou de charger certains appareils numériques mobiles et des smartphones même lorsque votre ordinateur est en mode veille ou hibernation.
10 Prise de sécurité : pour protéger votre station d'accueil contre le vol, vous pouvez utiliser un verrou avec câble de sécurité de type Kensington adapté à cette prise de sécurité pour fixer votre ordinateur à un bureau, une table ou tout autre point d'attache non permanent. ThinkPad Ultra Dock Vue avant 1 Interrupteur d'alimentation : appuyez sur l'interrupteur d'alimentation pour allumer ou éteindre l'ordinateur.
Vue arrière 1 Connecteur Always-On USB : permet de connecter des périphériques compatibles USB 2.0 ou de charger certains appareils numériques mobiles et des smartphones même lorsque votre ordinateur est en mode veille ou hibernation. 2 Connecteurs USB 2.0 : permet de connecter des périphériques compatibles USB 2.0. 3 Connecteurs USB 3.0 : permet de connecter des périphériques compatibles USB 3.0. 4 Connecteur Ethernet : permet de raccorder la station d'accueil à un réseau local Ethernet.
Connexion d'une station d'accueil ThinkPad Pour connecter votre ordinateur à une station d'accueil ThinkPad prise en charge, procédez comme suit : Remarque : La station d'accueil ThinkPad Basic Dock ne permet pas de verrouiller le système. 1. Débranchez tous les câbles et périphériques de l'ordinateur. 2. Assurez-vous que la clé de verrouillage du système est en position déverrouillée (horizontale). 3. Alignez la partie supérieure gauche de l'ordinateur avec le repère de la station d'accueil.
Remarque : La station d'accueil ThinkPad Basic Dock ne permet pas de verrouiller le système. 1. Débranchez tous les câbles et périphériques de l'ordinateur. 2. Assurez-vous que la clé de verrouillage du système est en position déverrouillée (horizontale). 3. Appuyez sur le bouton d'éjection jusqu'à ce que l'ordinateur se déplace vers le haut. Saisissez ensuite l'ordinateur par ses deux côtés, puis retirez-le.
– ThinkPad Ultra Dock • Pour le ThinkPad Ultra Dock, jusqu'à trois écrans (y compris l'écran de l'ordinateur) peuvent fonctionner en même temps. Par conséquent, si vous branchez trois écrans externes au ThinkPad Ultra Dock, l'écran branché au connecteur VGA ne fonctionnera pas lorsque l'écran de l'ordinateur sera activé.
• Lorsque la clé se trouve en position verrouillée (position 1), le bouton d'éjection de la station d'accueil est verrouillé et vous ne pouvez pas retirer votre ordinateur. Le voyant de verrouillage par clé est allumé lorsque le bouton d'éjection est verrouillé. • Lorsque la clé se trouve en position déverrouillée (position 2), le bouton d'éjection de la station d'accueil est déverrouillé et vous pouvez retirer votre ordinateur.
Chapitre 8. Configuration avancée Ce chapitre fournit les informations suivantes, nécessaires à la configuration de votre ordinateur : • « Installation d'un nouveau système d'exploitation » à la page 117 • « Installation de pilotes de périphérique » à la page 119 • « Utilisation du programme ThinkPad Setup » à la page 119 Installation d'un nouveau système d'exploitation Dans certains cas, vous devrez peut être installer un nouveau système d'exploitation.
d'accueil de la Base de connaissances Microsoft à l'adresse suivante : http://support.microsoft.com/ 9. Installez les correctifs de registre, par exemple Enabling Wake on LAN from Standby for ENERGY STAR. Pour télécharger et installer les correctifs de registre, consultez le site Web de support Lenovo à l'adresse suivante : http://www.lenovo.
8. Installez les programmes Lenovo selon vos préférences. Pour plus d'informations sur les programmes Lenovo, voir « Programmes Lenovo » à la page 15. Remarque : Après avoir installé le système d'exploitation, vous ne devez pas modifier le paramètre UEFI/Legacy Boot d'origine dans le programme ThinkPad Setup. Sinon, le système d'exploitation ne démarrera pas correctement. Lorsque vous installez le système d'exploitation Windows 8, Windows 8.
superviseur. Pour plus d'informations, reportez-vous à la section « Utilisation des mots de passe » à la page 55. 2. Utilisez les touches de déplacement du curseur pour sélectionner un onglet ou localiser une option, que vous pouvez ensuite sélectionner en appuyant sur Entrée. Un sous-menu s'affiche alors. Remarque : Certaines options ne s'affichent dans le menu que si l'ordinateur prend en charge les fonctions correspondantes. 3.
Tableau 2. Options de menu Config Option de menu Option de sous-menu Valeurs possibles Commentaires Network Wake On LAN • Disabled Permet d'activer la mise sous tension automatique de l'ordinateur lorsque le contrôleur Ethernet reçoit un paquet magique (message réseau spécial). • AC Only • AC and Battery Si vous sélectionnez AC Only, l'option Wake on LAN est activée uniquement si le boîtier d'alimentation est branché.
Tableau 2. Options de menu Config (suite) Option de menu Option de sous-menu Valeurs possibles Commentaires USB USB UEFI BIOS Support • Disabled Permet d'activer ou de désactiver la prise en charge de l'amorçage pour les périphériques de stockage USB. • Enabled Always-On USB • Disabled • Enabled Always-On USB - Charge in Battery Mode • Disabled USB 3.
Tableau 2. Options de menu Config (suite) Option de menu Option de sous-menu Valeurs possibles Commentaires Keyboard/Mouse TrackPoint • Disabled Permet d'activer ou de désactiver le dispositif de pointage TrackPoint intégré. • Enabled Remarque : Si vous souhaitez utiliser une souris externe, sélectionnez Disabled. Trackpad • Disabled • Enabled Permet d'activer ou de désactiver le pavé tactile intégré. Remarque : Si vous souhaitez utiliser une souris externe, sélectionnez Disabled.
Tableau 2. Options de menu Config (suite) Option de menu Option de sous-menu Valeurs possibles Commentaires Fn Sticky key • Disabled Si cette option est activée, vous pouvez appuyer sur la touche Fn pour qu'elle reste appuyée, puis sur la touche de fonction souhaitée. Cela revient à appuyer simultanément sur la touche souhaitée et la touche Fn. Si vous appuyez deux fois sur la touche Fn, celle-ci est verrouillée jusqu'à ce que vous appuyiez de nouveau dessus.
Tableau 2. Options de menu Config (suite) Option de menu Alimentation Option de sous-menu SpeedStep® Intel technology Valeurs possibles Commentaires • Disabled Vous pouvez choisir le mode de fonctionnement de la technologie Intel SpeedStep lors de l'exécution.
Tableau 2. Options de menu Config (suite) Option de menu Option de sous-menu Valeurs possibles Commentaires transfert qu'elle prend en charge. PCI Express Power Management • Disabled • Enabled Permet d'activer ou de désactiver une fonction qui règle automatiquement la gestion de l'alimentation lorsqu'aucune activité PCI Express n'est en cours. En règle générale, il n'est pas nécessaire de modifier ce paramètre.
Tableau 2. Options de menu Config (suite) Option de menu Option de sous-menu Valeurs possibles Commentaires Beep and Alarm Password Beep • Disabled Permet d'activer l'émission d'un signal sonore lorsque le système attend le mot de passe à la mise sous tension, d'accès au disque dur ou de superviseur. Les signaux sonores émis seront différents selon que le mot de passe saisi correspond ou non au mot de passe configuré.
Tableau 2. Options de menu Config (suite) Option de menu Option de sous-menu Valeurs possibles Commentaires Intel AMT Intel AMT Control • Disabled Si vous sélectionnez Enabled, Intel AMT (Active Management Technology) est configuré et des éléments de configuration supplémentaires sont indiqués dans la configuration MEBx (Management Engine BIOS Extension). • Enabled • Permanently Disabled Si vous sélectionnez Permanently Disabled, vous ne pourrez plus réactiver ce paramètre.
Menu Date/Time Pour modifier la date ou l'heure de votre ordinateur, sélectionnez l'onglet Date/Time dans le menu ThinkPad Setup. Procédez ensuite comme suit : 1. À l'aide des touches de déplacement du curseur, sélectionnez System Date ou System Time. 2. Entrez une date ou une heure. Menu Security Pour modifier les paramètres de sécurité de votre ordinateur, sélectionnez l'onglet Security dans le menu ThinkPad Setup. Le tableau suivant énumère les options du menu Security.
Tableau 3. Eléments du menu Security (suite) Option de menu Option de sous-menu Valeurs possibles Commentaires tension à partir d'un état hors tension ou hibernation. Si vous sélectionnez Disabled, aucune invite de mot de passe ne s'affiche ; l'ordinateur continue d'être exécuté et charge le système d'exploitation. Pour éviter tout accès illicite, définissez l'authentification utilisateur sur le système d'exploitation.
Tableau 3. Eléments du menu Security (suite) Option de menu Option de sous-menu Valeurs possibles Commentaires Fingerprint Predesktop Authentication • Disabled Permet d'activer ou de désactiver l'authentification par empreintes digitales avant le chargement du système d'exploitation.
Tableau 3. Eléments du menu Security (suite) Option de menu Option de sous-menu Valeurs possibles Commentaires UEFI BIOS Update Option Flash BIOS Updating by End-Users • Disabled Si vous sélectionnez Enabled, tout utilisateur peut mettre à jour l'interface UEFI BIOS. Si vous sélectionnez Disabled, seule la personne connaissant le mot de passe superviseur peut mettre à jour l'interface UEFI BIOS.
Tableau 3. Eléments du menu Security (suite) Option de menu Option de sous-menu Valeurs possibles Commentaires Intel TXT Feature • Disabled Permet d'activer ou de désactiver la technologie Intel Trusted Execution Technology. • Enabled Remarque : Cette option ne s'affiche que si vous avez sélectionné Active dans l'option Security Chip.
Tableau 3. Eléments du menu Security (suite) Option de menu Option de sous-menu Valeurs possibles Commentaires de mémoire virtuelle peut utiliser l'infrastructure de la plateforme pour une virtualisation des opérations d'entrée-sortie.
Tableau 3. Eléments du menu Security (suite) Option de menu Option de sous-menu Valeurs possibles Commentaires ExpressCard Slot • Disabled Si vous sélectionnez Enabled, vous pouvez utiliser l'emplacement pour carte ExpressCard. • Enabled Thunderbolt • Disabled Si vous sélectionnez Enabled, vous pouvez utiliser le connecteur Thunderbolt.
Tableau 3. Eléments du menu Security (suite) Option de menu Option de sous-menu Valeurs possibles Commentaires Secure Boot Secure Boot • Disabled Permet d'activer ou de désactiver la fonction UEFI Secure Boot. Sélectionnez Enabled pour éviter que des systèmes d'exploitation non autorisés ne s'exécutent lors de l'amorçage. Sélectionnez Disabled pour autoriser tous les systèmes d'exploitation à s'exécuter lors de l'amorçage. • Enabled Les systèmes d'exploitation Windows 8 et Windows 8.
Menu Startup Pour modifier les paramètres de démarrage de votre ordinateur, sélectionnez l'onglet Startup dans le menu ThinkPad Setup. Attention : • Une fois la séquence d'amorçage modifiée, veillez à sélectionner un périphérique approprié lorsque vous effectuez une copie, un enregistrement ou un formatage. Sinon, vous risquez de supprimer vos données. • Si vous utilisez le chiffrement de lecteur BitLocker, ne modifiez pas la séquence d'amorçage.
Tableau 4. Options de menu Startup (suite) Option de menu Valeurs possibles • No Commentaires système d'exploitation activé dans l'interface UEFI. Remarque : Si vous sélectionnez UEFI Only, l'ordinateur ne peut pas démarrer depuis des périphériques amorçables qui ne disposent d'aucun système d'exploitation activé dans l'interface UEFI. Le module de support de compatibilité (CSM) est requis pour démarrer le système d'exploitation existant. Si vous sélectionnez UEFI Only, CSM Support est sélectionnable.
• Load Setup Defaults : permet de restaurer les paramètres par défaut de votre ordinateur. Remarque : Activez OS Optimized Defaults pour répondre aux critères de certification de Windows 8, Windows 8.1 ou Windows 10. Lorsque vous modifiez ce paramètre, d'autres paramètres sont modifiés automatiquement, notamment CSM Support, UEFI/Legacy Boot, Secure Boot et Secure RollBack Prevention. • Discard Changes : permet d'annuler les modifications. • Save Changes : permet de sauvegarder les modifications.
Wake on LAN L'administrateur réseau peut utiliser la fonction Wake on LAN pour mettre un ordinateur sous tension à partir d'une console de gestion. Lorsque la fonction Wake on LAN est activée, de nombreuses fonctions peuvent être exécutées à distance sans surveillance, notamment le transfert de données, les mises à jour logicielles et les mises à jour flash du système UEFI BIOS.
4. Appuyez sur la touche F10 pour enregistrer et quitter. Remarque : Vous pouvez appuyer sur F9 pour restaurer les paramètres par défaut de votre ordinateur. Vérification des conditions requises pour les mises à jour flash Les programmes de votre ordinateur peuvent être mis à jour à distance par un administrateur réseau si les conditions suivantes sont réunies : • L'ordinateur doit être démarré à partir du réseau local.
142 Guide d'utilisation
Chapitre 9. Prévention des incidents Posséder un ordinateur portable ThinkPad implique d'en assurer la maintenance. Vous devez en prendre soin de manière à éviter les incidents les plus courants. Ce chapitre fournit des informations qui vous permettront de faire fonctionner l'ordinateur correctement.
• Si vous devez effectuer une récupération sur votre ordinateur afin de rétablir le contenu préinstallé sur la machine, les conseils suivants peuvent vous être utiles : – Retirez tous les périphériques externes tels que l'imprimante, le clavier, etc. – Assurez-vous que la batterie est chargée et que votre ordinateur est branché sur l'alimentation secteur. – Ouvrez ThinkPad Setup et chargez les paramètres par défaut. – Redémarrez l'ordinateur et démarrez l'opération de récupération.
affiche ensuite la liste des modules de mise à jour et classe chaque mise à jour en fonction des catégories critique, recommandée ou facultative afin de vous aider à déterminer leur importance. Vous contrôlez entièrement le téléchargement et l'installation des mises à jour. Une fois que vous avez sélectionné les modules de mise à jour de votre choix, le programme System Update télécharge et installe automatiquement les mises à jour sans autre intervention de votre part.
• Ne retournez pas l'ordinateur lorsque le boîtier d'alimentation est connecté afin de ne pas endommager la prise de ce dernier. Porter son ordinateur en le tenant correctement • Avant de déplacer votre ordinateur, veillez à enlever tout support et à débrancher toutes les unités ainsi que les cordons et les câbles. • Pour soulever l'ordinateur ouvert, tenez-le par sa base. Ne soulevez pas l'ordinateur par l'écran.
• La surface du lecteur d'empreintes digitales est sale ou tachée. • La surface du lecteur d'empreintes digitales est mouillée. • Il arrive souvent que le lecteur d'empreintes digitales ne parvienne pas à enregistrer ou authentifier votre empreinte digitale. Enregistrement de votre ordinateur • Enregistrez votre ordinateur ThinkPad auprès de Lenovo à l'adresse suivante : http://www.lenovo.com/register. Pour plus d'informations, voir « Enregistrement de votre ordinateur » à la page 19.
3. Si la tache est toujours présente, humidifiez un chiffon doux et non pelucheux avec de l'eau ou un mélange composé à 50 % d'alcool isopropylique et à 50 % d'eau et ne contenant aucune impureté. Remarque : Evitez de vaporiser un produit de nettoyage directement sur le clavier. 4. Essorez le chiffon pour éliminer autant de liquide que possible. 5. Essuyez l'écran de nouveau, en veillant à ne pas faire couler de liquide dans l'ordinateur. 6. Séchez bien l'écran avant de refermer l'ordinateur.
Chapitre 10. Résolution des incidents informatiques Ce chapitre décrit la procédure en cas d'incident sur votre ordinateur. • « Diagnostic des incidents » à la page 149 • « Identification et résolution des incidents » à la page 149 Diagnostic des incidents En cas d'incidents liés à l'utilisation de votre ordinateur, utilisez le programme Lenovo Solution Center comme point de départ pour les résoudre. Le programme Lenovo Solution Center vous permet de détecter et de résoudre des incidents informatiques.
1. Maintenez l'interrupteur d'alimentation enfoncé jusqu'à ce que l'ordinateur s'éteigne. Après que l'ordinateur soit éteint, redémarrez-le en appuyant de nouveau sur l'interrupteur d'alimentation. Si l'ordinateur ne s'allume pas, passez à l'étape 2. Remarque : Ne retirez pas la batterie ni le boîtier d'alimentation pour redémarrer l'ordinateur. 2. Une fois l'ordinateur hors tension, supprimez toutes ses sources d'alimentation (batterie et boîtier d'alimentation).
Messages d'erreur • Message : 0177 : Données SVP incorrectes - Arrêtez la fonction d'autotest à la mise sous tension. Solution : Le total de contrôle du mot de passe superviseur de l'EEPROM est incorrect. La carte principale doit être remplacée. Faites réparer l'ordinateur. • Message : 0183 : CRC incorrect des paramètres de sécurité dans l'EFI Variable. Lancez le programme ThinkPad Setup. Solution : Le total de contrôle des paramètres de sécurité de l'EFI Variable est incorrect.
• Message : 2102 : Erreur de détection sur SSD2 (M.2) Solution : Le périphérique M.2 SSD ne fonctionne pas. Faites réparer le périphérique M.2 SSD. • Message : 2110 : Erreur de lecture sur HDD0 (disque dur principal). Solution : L'unité de disque dur ne fonctionne pas. Faites réparer l'unité de disque dur. • Message : 2111 : Erreur de lecture sur HDD1 (disque dur Ultrabay). Solution : L'unité de disque dur ne fonctionne pas. Faites réparer l'unité de disque dur.
• Incident : Au démarrage de l'ordinateur, seul un curseur blanc s'affiche sur un écran vide. Solution : Si vous avez modifié une partition sur votre unité de disque dur ou sur votre unité SDD en utilisant un logiciel de partition, il est possible que les informations relatives à cette partition ou que l'enregistrement d'initialisation principal soit détruit. 1. Eteignez votre ordinateur, puis rallumez-le. 2.
4. Vérifiez la configuration et la compatibilité de la mémoire, y compris la taille de mémoire maximale et la vitesse de la mémoire. 5. Exécutez les programmes de diagnostic. Voir « Diagnostic des incidents » à la page 149. Incidents liés à l'utilisation en réseau Voici les incidents les plus courants liés à l'utilisation en réseau : Incidents liés à Ethernet • Incident : Votre ordinateur ne peut pas se connecter au réseau. Solution : Vérifiez que : – Le câble est installé correctement.
• Incident : Si un modèle Gigabit Ethernet est utilisé, celui-ci ne peut pas se connecter au réseau à une vitesse de 1000 Mbit/s. En revanche, il se connecte à 100 Mbit/s. Solution : – Essayez un autre câble. – Vérifiez que le partenaire de liaison est défini pour une négociation automatique. – Vérifiez que le commutateur est conforme à la norme 802.3ab (Gigabit sur cuivre).
périphérique compatible Bluetooth peut recevoir un fichier via Bluetooth, un élément PIM envoyé depuis Windows 7 devrait pouvoir être enregistré sous forme de fichier avec l'extension .contact. Incidents liés au clavier et aux autres dispositifs de pointage Voici les incidents les plus courants liés au clavier et aux autres dispositifs de pointage.
Incidents liés à l'écran de l'ordinateur • Incident : L'écran reste noir. Solution : Procédez comme suit : – Appuyez sur la touche F7 pour faire apparaître l'image. – Si vous utilisez le boîtier d'alimentation ou la batterie et que la jauge de batterie indique que la batterie n'est pas déchargée, appuyez sur la touche F6 pour éclaircir l'affichage. – Si votre ordinateur est en mode veille, appuyez sur la touche Fn pour quitter ce mode.
• Incident : L'écran reste allumé même après la mise hors tension de l'ordinateur. Solution : Maintenez l'interrupteur d'alimentation enfoncé pendant au moins quatre secondes pour éteindre l'ordinateur, puis rallumez-le. • Incident : Des points manquants, décolorés ou brillants s'affichent à chaque mise sous tension de l'ordinateur. Solution : Il s'agit d'une caractéristique de la technologie TFT. L'écran de l'ordinateur contient de nombreux transistors à couche mince (TFT).
– Sous Windows 10 : cliquez sur Propriétés de la carte graphique. 6. Cliquez sur l'onglet Ecran. 7. Sélectionnez la fréquence de rafraîchissement de l'écran appropriée. • Incident : Des caractères incorrects s'affichent à l'écran. Solution : Avez-vous correctement suivi la procédure d'installation du système d'exploitation ou du programme ? Si c'est le cas, faites réparer l'écran externe. • Incident : La fonction d'extension du bureau ne fonctionne pas. Solution : Activez la fonction d'extension du bureau.
5. Sélectionnez Microphone et cliquez sur le bouton Propriétés. 6. Cliquez sur l'onglet Niveaux, puis déplacez le curseur d'amplification du micro vers le haut. 7. Cliquez sur OK. Remarque : Pour plus de détails sur le réglage du volume, reportez-vous à l'aide en ligne de Windows. • Incident : Il est impossible de déplacer un curseur de volume ou de balance. Solution : Si le curseur est grisé (désactivé), cela signifie que sa position est figée par le matériel et vous ne pouvez pas la modifier.
Incidents liés à la batterie et à l'alimentation Cette rubrique fournit des instructions sur la batterie et l'identification des incidents relatifs à l'alimentation. Incidents liés à la batterie • Incident : La batterie ne peut pas être chargée complètement dans le délai de charge standard lorsque l'ordinateur est hors tension. Solution : La batterie est peut-être trop déchargée. Procédez comme suit : 1. Mettez l'ordinateur hors tension. 2.
Si votre ordinateur n'est pas du tout alimenté, vérifiez les éléments suivants : 1. Vérifiez l'interrupteur d'alimentation. L'interrupteur d'alimentation s'allume lorsque l'ordinateur est sous tension. 2. Vérifiez toutes les connexion d'alimentation. Retirez les multiprises et les dispositifs de protection contre les surtensions pour brancher le boîtier d'alimentation directement sur le socle de la prise de courant. 3. Inspectez le boîtier d'alimentation.
• Incident : Une erreur de très faible charge de la batterie se produit et l'ordinateur s'arrête immédiatement. Solution : La charge de la batterie est faible. Branchez le boîtier d'alimentation sur une prise de courant et connectez-le à l'ordinateur ou remplacez la batterie par une batterie chargée. • Incident : L'écran de l'ordinateur n'affiche rien après utilisation de la touche Fn pour sortir du mode veille.
Solution : Dans le menu Startup de ThinkPad Setup, assurez-vous que l'unité de disque dur figure dans la liste Boot priority order. Si l'unité figure dans la liste Excluded from boot order , elle est désactivée. Sélectionnez l'entrée correspondante dans la liste et appuyez Shift+1 pour la déplacer dans la liste Boot priority order. • Incident : Après avoir défini un mot de passe d'accès au disque dur, vous avez placé l'unité de disque dur dans un autre ordinateur.
– CD de photo multisession – CD vidéo – DVD-ROM (DVD vidéo) • Incident : L'ordinateur ne peut pas lire de CD ou la qualité du son est mauvaise. Solution : Vérifiez que le disque respecte les normes de votre pays. Généralement, les disques respectant ces normes portent un logo sur leur jaquette. Si vous utilisez un disque non conforme, nous ne pouvons garantir ni sa lecture ni la qualité du son. Incident lié à un logiciel Incident : Une application ne fonctionne pas correctement.
• Le boîtier d'alimentation est connecté à la station d'accueil. • L'ordinateur est correctement raccordé à la station d'accueil.
Chapitre 11. Support Ce chapitre fournit des informations concernant l'aide et le support Lenovo.
Assistance et services Si vous avez besoin d'une aide, d'un service, d'une assistance technique, ou que vous voulez simplement obtenir plus d'informations sur les produits Lenovo, de nombreuses sources Lenovo sont à votre disposition. Cette rubrique concerne les sources d'informations sur Lenovo et ses produits, ce qu'il faut faire en cas d'incident sur votre ordinateur et les personnes à contacter si une intervention est nécessaire.
Appeler Lenovo Si vous avez essayé de résoudre un incident par vous-même et si vous avez tout de même besoin d'aide, vous pouvez, pendant la période de garantie, obtenir de l'aide et des informations par téléphone auprès du Centre de support client. Les services suivants sont disponibles pendant la période de garantie : • Identification d'incidents - Des techniciens sont à votre disposition pour vous aider à déterminer si l'incident est d'origine matérielle et à le résoudre.
Pour plus d'informations sur ces services, accédez au site Web suivant : http://www.lenovo.
Annexe A. Informations réglementaires Emplacement des antennes sans fil UltraConnect Les ordinateurs portables ThinkPad disposent d'un système d'antennes sans fil UltraConnect™ intégré à l'affichage pour une réception optimale, permettant ainsi une communication sans fil où que vous soyez. Il existe deux types d'emplacement pour ces antennes.
1 2 Antenne réseau local sans fil (auxiliaire) Antenne réseau local sans fil (principale) Informations liées à la communication sans fil Interopérabilité sans fil La carte réseau local sans fil est conçue pour pouvoir être utilisée avec un autre produit de réseau local reposant sur les technologies radio Direct Sequence Spread Spectrum (DSSS), Complementary Code Keying (CCK), et/ou Orthogonal Frequency Division Multiplexing (OFDM), et est conforme : • A la norme 802.11b/g, 802.11a/b/g ou 802.
Environnement d'utilisation et santé Les cartes sans fil intégrées émettent de l'énergie électromagnétique de radiofréquence comme les autres appareils radioélectriques. Cependant, le niveau d'énergie émis par celles-ci est beaucoup moins important que l'énergie électromagnétique émise par des appareils sans fil (téléphones mobiles).
Si votre ordinateur est fourni sans le document Regulatory Notice, ce dernier est disponible sur le site Web à l'adresse suivante : http://www.lenovo.com/UserManual Informations sur la certification Le tableau suivant contient des informations sur le nom du produit, l'ID de conformité et les types de machines.
Responsible Party: Lenovo (United States) Incorporated 1009 Think Place - Building One Morrisville, NC 27560 Phone Number: 919-294-5900 Avis de conformité à la réglementation d'Industrie Canada pour la classe B CAN ICES-3(B)/NMB-3(B) Directive de l'Union européenne relative à la conformité électromagnétique Le présent produit satisfait aux exigences en matière de protection énoncées dans la directive 2004/108/CE du Parlement européen et du Conseil relative au rapprochement des législations des États membr
Zulassungsbescheinigung laut dem Deutschen Gesetz über die elektromagnetische Verträglichkeit von Betriebsmitteln, EMVG vom 20. Juli 2007 (früher Gesetz über die elektromagnetische Verträglichkeit von Geräten), bzw. der EMV EG Richtlinie 2004/108/EC (früher 89/336/EWG), für Geräte der Klasse B. Dieses Gerät ist berechtigt, in Übereinstimmung mit dem Deutschen EMVG das EG-Konformitätszeichen - CE - zu führen.
Notice relative à la réglementation pour le Mexique Advertencia: En Mexico la operación de este equipo estásujeta a las siguientes dos condiciones: (1) es posible que este equipo o dispositivo no cause interferencia perjudicial y (2) este equipo o dispositivo debe aceptar cualquier interferencia, incluyendo la que pueda causar su operación no deseada. Annexe A.
178 Guide d'utilisation
Annexe B. Déclarations relatives au recyclage et aux DEEE Lenovo encourage les propriétaires de matériel informatique à recycler leur matériel dès lors que celui-ci n'est plus utilisé. Lenovo propose une gamme de programmes et services concernant le recyclage du matériel informatique. Des informations relatives aux offres de recyclage sont disponibles sur le site Internet de Lenovo à l'adresse suivante : http://www.lenovo.com/social_responsibility/us/en/.
Déclarations relatives au recyclage pour le Japon Collecting and recycling a disused Lenovo computer or monitor If you are a company employee and need to dispose of a Lenovo computer or monitor that is the property of the company, you must do so in accordance with the Law for Promotion of Effective Utilization of Resources. Computers and monitors are categorized as industrial waste and should be properly disposed of by an industrial waste disposal contractor certified by a local government.
A Lenovo possui um canal específico para auxiliá-lo no descarte desses produtos. Caso você possua um produto Lenovo em situação de descarte, ligue para o nosso SAC ou encaminhe um e-mail para: reciclar@lenovo.com, informando o modelo, número de série e cidade, a fim de enviarmos as instruções para o correto descarte do seu produto Lenovo. Informations sur le recyclage des piles et batteries pour l'Union européenne Remarque : Ce logo s'applique uniquement aux pays de l'Union Européenne (EU).
Informations sur le recyclage des piles et batteries pour les Etats-Unis et le Canada 182 Guide d'utilisation
Annexe C. Directive RoHS (Restriction of Hazardous Substances) Directive RoHS pour l'Union européenne Lenovo products sold in the European Union, on or after 3 January 2013 meet the requirements of Directive 2011/65/EU on the restriction of the use of certain hazardous substances in electrical and electronic equipment (“RoHS recast” or “RoHS 2”). For more information about Lenovo progress on RoHS, go to: http://www.lenovo.com/social_responsibility/us/en/RoHS_Communication.
Directive RoHS pour la Chine Directive RoHS pour l'Inde RoHS compliant as per E-Waste (Management & Handling) Rules, 2011.
Directive RoHS pour la Turquie The Lenovo product meets the requirements of the Republic of Turkey Directive on the Restriction of the Use of Certain Hazardous Substances in Waste Electrical and Electronic Equipment (WEEE). Directive RoHS pour l'Ukraine Annexe C.
186 Guide d'utilisation
Annexe D. Informations sur les modèles ENERGY STAR ENERGY STAR® est un programme commun de l'agence américaine de protection de l'environnement (U.S. Environmental Protection Agency) et du département américain à l'énergie (U.S. Department of Energy) qui a pour but d'économiser de l'argent et de protéger l'environnement par le biais de produits et de pratiques efficaces. Lenovo est fier d'offrir à ses clients des produits répondant aux normes fixées par le programme ENERGY STAR.
3. Cliquez avec le bouton droit de la souris sur votre périphérique de carte réseau, puis cliquez sur Propriétés. 4. Cliquez sur l'onglet Gestion de l'alimentation. 5. Décochez la case Autoriser ce périphérique à sortir l'ordinateur du mode veille. 6. Cliquez sur OK.
Annexe E. Remarques Ce document peut contenir des informations ou des références concernant certains produits, logiciels ou services Lenovo non annoncés dans ce pays. Pour plus de détails, référez-vous aux documents d'annonce disponibles dans votre pays, ou adressez-vous à votre partenaire commercial Lenovo. Toute référence à un produit, logiciel ou service Lenovo n'implique pas que seul ce produit, logiciel ou service puisse être utilisé.
Marques Les termes qui suivent sont des marques de Lenovo aux Etats-Unis et/ou dans certains autres pays : Access Connections Active Protection System Lenovo Secure Data Disposal ThinkPad TrackPoint Ultrabay UltraConnect Intel, Intel SpeedStep et Thunderbolt sont des marques d'Intel Corporation aux États-Unis et/ou dans certains autres pays. Microsoft, BitLocker, Windows et Cortana sont des marques du groupe Microsoft.