ThinkServer TS130 Hardware Maintenance Manual Machine Types: 1098, 1100, 1105, and 1106
Note: Before using this information and the product it supports, read the general information in Appendix C “Notices” on page 109 and the Warranty and Support Information document on the documentation DVD. First Edition (May 2011) © Copyright Lenovo 2011. LIMITED AND RESTRICTED RIGHTS NOTICE: If data or software is delivered pursuant a General Services Administration “GSA” contract, use, reproduction, or disclosure is subject to restrictions set forth in Contract No. GS-35F-05925.
Contents Chapter 1. About this manual . . . . . 1 Important Safety Information . . . . Safety information . . . . . . . . Important information about replacing compliant FRUs . . . . . . . . . . . . . . . . . . . . . RoHS . . . . . . 1 2 7 Chapter 2. General information. . . . . 9 Features and specifications. . . . . . . . Software programs . . . . . . . . . . . EasyStartup . . . . . . . . . . . . Reliability, availability, and serviceability . . . . . . . 9 . 11 . 11 . 11 Chapter 3.
Configuring the system BIOS to enable SATA RAID functionality. . . . . . . . . . . . Creating RAID volumes . . . . . . . . . Deleting RAID volumes . . . . . . . . . Resetting disks to non-RAID . . . . . . . Updating the firmware. . . . . . . . . . . . Using the EasyUpdate Firmware Updater program . . . . . . . . . . . . . . . Using the ThinkServer EasyStartup program . . . Updating system programs . . . . . . . . . . Using system programs . . . . . . . . . Updating (flashing) the BIOS from a disc. . .
Chapter 1. About this manual This Hardware Maintenance Manual contains information to help you solve problems that might occur in your server. It describes the diagnostic tools that come with the server, error codes and suggested actions, and instructions for replacing failing components. Replaceable components are of three types: • Self-service customer replaceable unit (CRU): Replacement of self-service CRUs is your responsibility.
Safety information Important: Each caution and danger statement in this document is labeled with a number. This number is used to cross reference an English-language caution or danger statement with translated versions of the caution or danger statement in the Safety Information document. For example, if a danger statement is labeled “Statement 1,” translations for this danger statement are in the Safety Information document under “Statement 1.
Statement 2 DANGER Danger of explosion if battery is incorrectly replaced. When replacing the lithium coin cell battery, use only the same or an equivalent type that is recommended by the manufacturer. The battery contains lithium and can explode if not properly used, handled, or disposed of. Do not: • Throw or immerse into water • Heat to more than 100°C (212°F) • Repair or disassemble Dispose of the battery as required by local ordinances or regulations.
Statement 4 ≥ 18 kg (39.7 lb) ≥ 32 kg (70.5 lb) ≥ 55 kg (121.2 lb) < 32 kg (70.5 lb) < 55 kg (121.2 lb) < 100 kg (220.5 lb) CAUTION: Use safe practices when lifting. Statement 5 CAUTION: The power control button on the device and the power switch on the power supply do not turn off the electrical current supplied to the device. The device also might have more than one power cord. To remove all electrical current from the device, ensure that all power cords are disconnected from the power source.
Statement 8 CAUTION: Never remove the cover on a power supply or any part that has the following label attached. Hazardous voltage, current, and energy levels are present inside any component that has this label attached. There are no serviceable parts inside these components. If you suspect a problem with one of these parts, contact a service technician. Statement 9 CAUTION: To avoid personal injury, disconnect the hot-swap fan cables before removing the fan from the device.
Statement 13 CAUTION: Make sure that the rack is secured properly to avoid tipping when the server unit is extended. Statement 14 CAUTION: Some accessory or option board outputs exceed Class 2 or limited power source limits and must be installed with appropriate interconnecting cabling in accordance with the national electric code. Statement 15 CAUTION: The power-control button on the device does not turn off the electrical current supplied to the device.
Statement 18 CAUTION: Do not place any object on top of rack-mounted devices. Statement 19 CAUTION: Hazardous moving parts. Keep fingers and other body parts away. Statement 20 CAUTION: The battery is a lithium ion battery. To avoid possible explosion, do not burn the battery. Exchange it only with the Lenovo-approved part. Recycle or discard the battery as instructed by local regulations.
RoHS compliant ThinkServer® TS130 parts have unique FRU part numbers. Before or after June 2006, failed RoHS compliant parts must always be replaced using RoHS compliant FRUs, so only the FRUs identified as compliant in the system Hardware Maintenance Manual or direct substitutions for those FRUs can be used.
Chapter 2. General information This chapter provides some general information about your server. Features and specifications The following table provides information about the features and specifications of the server. Depending on the server model, some features might not be available, or some specifications might not apply. For information about your specific model, use the Setup Utility program. See “Using the Setup Utility program” on page 83.
Table 1. Features and specifications Microprocessor(s): Support up to two Intel® Xeon® dual-core, quad-core, or hex-core microprocessors (internal cache size varies by model type) Expansion • Two optical drive bays • Two hard disk drive bays For the specific type and speed information about the microprocessor, use the Setup Utility program. See “Using the Setup Utility program” on page 83.
Table 1. Features and specifications (continued) Integrated functions: • Ethernet controllers (The server comes with two integrated Gigabit Ethernet controllers, which support connection to 100 Mbps or 1000 Mbps network.) • One serial port • One Video Graphics Array (VGA) monitor connector • Six USB connectors (two front and four rear) • One RJ-45 Ethernet connectors on the rear panel • Eight diagnostic LEDs Size: • Width: 174.8 mm (6.88 inches) • Height: 377.3 mm (14.85 inches) • Depth: 406.7 mm (16.
• Advanced Configuration and Power Interface (ACPI) • Advanced Desktop Management Interface (DMI) • Automatic memory downsizing on error detection • Automatic restart on non-maskable interrupt (NMI) • Availability of microcode level • Built-in, menu-driven setup, system configuration, and RAID configuration • Built-in monitoring for fan, temperature, and voltage • Cooling fans with speed-sensing capability • ECC DDR3 SDRAM with Serial Presence Detect (SPD) • Error codes and messages to help you identify pro
Chapter 3. Diagnostics and troubleshooting This chapter introduces some basic diagnostic and troubleshooting programs. If your server problem is not described here, see Appendix B “Help and service” on page 107 for additional troubleshooting resources.
4. Remove the diagnostic disc from the optical drive when you complete the diagnostic process. Navigating through the diagnostic program Use the cursor movement keys to navigate through the menus. • To select a menu item, press Enter. • To return to the previous menu, press Esc. • To view the help information system, press F1. Running tests There are four ways to run the diagnostic tests.
• Text: Description of the error. Note: See “POST error codes” on page 17 for error code listings. Formatting the hard disk drive The diagnostics program offers two hard disk drive formatting methods: • Quick Erase • Full Erase The quick erase method provides a DOS utility that performs the following: • Destroys the Master Boot Record (MBR) on the hard disk drive. • Destroys all copies of the FAT Table on all partitions (both the master and backup). • Destroys the partition table.
Symptom The server does not start when you press the power switch. Action Verify that: • The power cord is correctly connected to the rear of the server and to a working electrical outlet. • If your server has a secondary power switch on the rear of the server, make sure that it is switched on. • The power indicator on the front of the server is on. • The server voltage matches the voltage available at the electrical outlet for your country or region. The monitor screen is blank.
Symptom FRU/Action The boot sector on the startup drive is corrupted. The drive must be formatted. Do the following: 1. Attempt to back up the data on the failing hard disk drive. 2. Using the operating system programs, format the hard disk drive. Replace the hard disk drive. The drive is defective. Power supply problems If you suspect a power supply problem, use the following procedures. Check/Verify FRU/Action Check the following for proper installation. Reseat connectors.
If the POST detects a problem, an error message will be displayed on the screen. A single problem can cause several error messages. When you correct the cause of the first error message, probably the other error messages will not be displayed the next time you turn on the computer. POST error code POST error message Description/Action 00CE Machine Type or Serial Number is INVALID This error message is displayed when the machine type or the serial number is invalid.
POST error code 0176 POST error message System security - The system has been tampered with Description/Action This error message is displayed when the computer is turned on with the cover open or removed. Press F1 to enter the Setup Utility program. Then press F10 to save the operation and exit the Setup Utility program. 0189 System security - Can not read the Security EEPROM This error message indicates that the Security EEPROM might be broken or have been removed.
Miscellaneous error messages Symptom FRU/Action Changing display colors Display/Monitor Computer will not turn off. See “Hard disk drive boot error” on page 17. 1. Power switch 2. System board 3. Riser card, if installed. Computer will not RPL from server 1. Ensure that Network is set as the first device or it is after CD/DVD in the startup sequence. 2. Ensure that the network adapter is enabled for RPL. 3.
Symptom FRU/Action Other display symptoms not listed above (including blank or illegible display) 1. Display Turn on indicator or hard disk drive in-use light not on, but computer works correctly 1. Power switch/LED assembly Printer problems 1. Printer 2. System board 2. System board 2. System board Program loads from the hard disk with a known-good diagnostics diskette in the first 3.5-inch diskette drive 1. Run the Setup Utility program and check startup sequence. 2. Check the diskette drive.
e. External cache f. External cache RAM g. Hard disk drive h. Diskette drive 3. Turn on the server to re-test the system. 4. Repeat steps 1 through 3 until you find the failing components. If all devices and adapters have been removed, and the problem continues, replace the system board.
Chapter 4. Locating parts, controls, LEDs, and connectors This chapter provides information to help you locate your server parts, controls, light-emitting diodes (LEDs), and connectors. Front view Figure 1 “Front control and connector locations” on page 23 shows the locations of the controls and connectors on the front of your server. Figure 1.
Table 3. Front control panel LEDs LED State Color Power LED On Green The server power is on. Blinking Green The server power is in ACPI S1 mode, which is also known as Power On Suspend (POS) mode. In this mode, the microprocessor is not working while other hardware devices are still working. Off Off The server power is off. Off Off The hard disk drive is not active. Blinking Green Hard disk drive LED Description The hard disk drive is active.
Connector Description Audio line-in connector Used to receive audio signals from an external audio device, such as a stereo system. When you attach an external audio device, a cable connects the audio line-out connector of the device to the audio line-in connector of the server.
Locating parts on the system board Figure 3 “System board part locations” on page 26 shows the locations of the parts on the system board. Figure 3.
Internal components Figure 4 “Component locations” on page 27 shows the locations of the various components in your server. To remove the server cover and access to the inside of the server, see “Removing the server cover” on page 33. Figure 4.
28 ThinkServer TS130 Hardware Maintenance Manual
Chapter 5. Replacing FRUs This chapter provides detailed instructions for replacing FRUs in the server. FRU replacements are to be done only by trained service technicians. This chapter does not contain the remove or replace procedure for all FRUs. Only the major FRUs are documented. Guidelines This section provides some guidelines that you should read and understand before using your server.
• To view the error LEDs on the system board and internal components, leave the server connected to power. • You do not have to turn off the server to install or replace hot-swap fans, redundant hot-swap ac power supplies, or hot-plug USB devices. However, you must turn off the server before performing any steps that involve installing, removing, or replacing adapter cables or non-hot-swap optional devices or components.
• Take additional care when handling devices during cold weather. Heating reduces indoor humidity and increases static electricity. Working inside the server with the power on Attention: Static electricity that is released to internal server components when the server is turned on might cause the server to halt, which might result in the loss of data.
4. Remove the cover. 5. Check for any obvious non-Lenovo alterations. Use good judgment as to the safety of any non-Lenovo alterations. 6. Check inside the server for any obvious unsafe conditions, such as metal filings, contamination, water or other liquid, or signs of fire or smoke damage. 7. Check for worn, frayed, or pinched cables. 8. Make sure that the power-supply cover fasteners (screws or rivets) have not been removed or tampered with.
Removing the server cover Attention: Do not open your server or attempt any repair before reading and understanding the Safety Information and the Warranty and Support Information on the documentation DVD that came with your product, and “Guidelines” on page 29. To obtain a copy of the publications, go to: http://www.lenovo.com/support This section provides instructions on how to remove the server cover.
Removing and reinstalling the front bezel Attention: Do not open your server or attempt any repair before reading and understanding the Safety Information and the Warranty and Support Information on the documentation DVD that came with your product, and “Guidelines” on page 29. To obtain a copy of the publications, go to: http://www.lenovo.com/support This section provides instructions on how to remove and reinstall the front bezel. To remove and reinstall the front bezel, do the following: 1.
4. To reinstall the front bezel, align the three plastic tabs on the right side of the front bezel with the corresponding holes in the chassis, then pivot the front bezel inward until it snaps into position on the left side. Figure 7. Reinstalling the front bezel What to do next: • To work with another piece of hardware, go to the appropriate section. • To complete the installation or replacement, go to “Completing the parts replacement” on page 66.
To install or replace a PCI card, do the following: 1. Remove all media from the drives and turn off all attached devices and the server. Then, disconnect all power cords from electrical outlets and disconnect all cables that are connected to the server. 2. Remove the server cover. See “Removing the server cover” on page 33. 3. At the rear of the server, press the release button 1 to open the PCI card latch 2 . Figure 8.
4. If you are installing a PCI card, remove the appropriate metal slot cover. If you are replacing an old PCI card, grasp the old card that is currently installed and gently pull it out of the slot. Notes: a. The PCI card fits tightly into the card slot. If necessary, alternate moving each side of the card a small and equal amount until it is completely removed from the card slot. b. If the PCI card is held in place by a retaining latch, press the card retaining latch 1 as shown to disengage the latch.
7. Pivot the PCI card latch to the closed position to secure the PCI card. Figure 10. Installing a PCI card What to do next: • To work with another piece of hardware, go to the appropriate section. • To complete the installation or replacement, go to “Completing the parts replacement” on page 66.
If you are using the Microsoft Windows operating systems, you need to install the device driver for the Ethernet card. To install the device driver on Windows operating systems, do the following: 1. Save any open documents and exit all applications. 2. Insert the ThinkServer EasyStartup DVD that came with your server into the DVD drive. Note: You do not need to use the driver disc that came with the Ethernet card. 3. Right-click My Computer and select Properties. The System Properties window opens. 4.
• If you are replacing an old memory module, open the retaining clips and gently pull the memory module out of the memory slot. Figure 11. Removing a memory module • If you are installing a new memory module, open the retaining clips of the memory slot into which you want to install the memory module. Figure 12. Opening the retaining clips 7. Touch the static-protective package that contains the new memory module to any unpainted metal surface on the outside of the server.
8. Position the new memory module over the memory slot. Make sure that the notch 1 on the new memory module is aligned with the key 2 in the memory slot. Then, press the new memory module straight down into the memory slot until the retaining clips close and the new memory module snaps into position. Note: If there is a gap between the memory module and the retaining clips, the memory module has not been correctly installed.
• If you are replacing an optical drive, disconnect the signal cable and the power cable from the rear of the optical drive, press the blue release button and then slide the optical drive out of the front of the server. Figure 14. Removing the optical drive 5. Slide the new optical drive with the optical drive retainer 1 installed into the drive bay from the front of the server until the optical drive snaps into position. Figure 15.
6. Reinstall the front bezel. See “Removing and reinstalling the front bezel” on page 34. 7. Connect one end of the signal cable to the optical drive and the other end to an available SATA connector on the system board. See “Locating parts on the system board” on page 26. Then, locate an available five-wire power connector and connect it to the SATA drive. Figure 16. Connecting a SATA optical drive What to do next: • To work with another piece of hardware, go to the appropriate section.
5. Press the blue release tab 1 downward, slide the hard disk drive cage 2 to the rear of the server, and then pivot it outward to completely remove the drive cage from the chassis. Then, pull on the blue handle 3 to remove the hard disk drive from the drive cage. Figure 17. Removing the primary hard disk drive 6. Flex the sides of the blue bracket to remove the hard disk drive from the bracket. 7.
8. Slide the new hard disk drive with the blue bracket into the drive cage until it snaps into position and align the hard disk drive cage pivot pin with the slot 1 in the upper drive cage. Then, slide the hard disk drive cage into the chassis. Press down on the metal latch 2 and pivot the hard disk drive cage into place. Then, slide the drive cage to the front of the server until it snaps into position. Note: There are two arrows, one on the upper drive cage and one on the hard disk drive cage.
9. Connect one end of the signal cable to the hard disk drive and the other end to an available SATA connector on the system board. See “Locating parts on the system board” on page 26. Then, locate an available five-wire power connector and connect it to the hard disk drive. Figure 20. Connecting a SATA hard disk drive What to do next: • To work with another piece of hardware, go to the appropriate section. • To complete the replacement, go to “Completing the parts replacement” on page 66.
5. Press the release button 1 to release the hard disk drive cage and then lift the hard disk drive cage out of the chassis. Figure 21. Removing the secondary hard disk drive 6. Pull on the blue handle to release and remove the hard disk drive from the hard disk drive cage. 7. Flex the sides of the blue bracket to remove the hard disk drive from the bracket. 8.
9. Slide the new hard disk drive with the blue bracket into the secondary hard disk drive cage until it snaps into position. 10. Slide the hard disk drive cage with the new hard disk drive into the chassis until it is directly underneath the metal tab 1 . Figure 23.
11. Press the hard disk drive cage downward until it snaps into position. Make sure that the hard disk drive cage is secured in the chassis. Figure 24. Installing the secondary hard disk drive 12. Connect one end of the signal cable to the hard disk drive and the other end to an available SATA connector on the system board. See “Locating parts on the system board” on page 26. Then, locate an available five-wire power connector and connect it to the hard disk drive. Figure 25.
Replacing the power supply assembly Attention: Do not open your server or attempt any repair before reading and understanding the Safety Information and the Warranty and Support Information on the documentation DVD that came with your product, and “Guidelines” on page 29. To obtain a copy of the publications, go to: http://www.lenovo.com/support This section provides instructions on how to replace the power supply assembly.
4. Remove the four screws at the rear of the chassis that secure the power supply assembly. Figure 26. Removing the screws that secure the power supply assembly 5. Slide the power supply assembly a little bit forward and then remove it from the chassis. Figure 27. Removing the power supply assembly 6. Ensure that the new power supply assembly is the correct replacement. 7.
What to do next: • To work with another piece of hardware, go to the appropriate section. • To complete the replacement, go to “Completing the parts replacement” on page 66. Replacing the heat sink and fan assembly Attention: Do not open your server or attempt any repair before reading and understanding the Safety Information and the Warranty and Support Information on the documentation DVD that came with your product, and “Guidelines” on page 29. To obtain a copy of the publications, go to: http://www.
6. Follow this sequence to remove the four screws that secure the heat sink and fan assembly to the system board: a. Partially remove screw 1 , then fully remove screw 2 , and then fully remove screw 1 . b. Partially remove screw 3 , then fully remove screw 4 , and then fully remove screw 3 . Note: Carefully remove the four screws from the system board to avoid any possible damage to the system board. The four screws cannot be removed from the heat sink and fan assembly. Figure 28.
• To complete the replacement, go to “Completing the parts replacement” on page 66. Replacing the front audio and USB assembly Attention: Do not open your server or attempt any repair before reading and understanding the Safety Information and the Warranty and Support Information on the documentation DVD that came with your product, and “Guidelines” on page 29. To obtain a copy of the publications, go to: http://www.lenovo.
10. Reinstall the front bezel. See “Removing and reinstalling the front bezel” on page 34. What to do next: • To work with another piece of hardware, go to the appropriate section. • To complete the replacement, go to “Completing the parts replacement” on page 66.
5. Release the two tabs 1 that attach the front fan assembly to the chassis as shown and then completely remove the front fan assembly from the chassis. Figure 30.
6. Insert the two tabs 2 of the new front fan assembly into the corresponding holes in the chassis, and press the other two tabs 1 through the holes until the front fan assembly is secured in place. Figure 31. Installing the front fan assembly 7. Connect the new front fan assembly cable to the power fan connector on the system board. See “Locating parts on the system board” on page 26. What to do next: • To work with another piece of hardware, go to the appropriate section.
2. Remove the server cover. See “Removing the server cover” on page 33. 3. Locate the rear fan assembly. See “Internal components” on page 27. 4. Disconnect the rear fan assembly cable from the system fan connector on the system board. See “Locating parts on the system board” on page 26. 5. The rear fan assembly is attached to the chassis by four rubber mounts. Remove the rear fan assembly by cutting the rubber mounts and gently pulling the rear fan assembly out of the chassis. Figure 32.
7. Carefully pull on the tips of the rubber mounts until the new rear fan assembly is secured in place. Figure 33. Installing the rear fan assembly 8. Connect the new rear fan assembly cable to the system fan connector on the system board. See “Locating parts on the system board” on page 26. What to do next: • To work with another piece of hardware, go to the appropriate section. • To complete the replacement, go to “Completing the parts replacement” on page 66.
To replace the microprocessor, do the following: 1. Remove all media from the drives and turn off all attached devices and the computer. Then, disconnect all power cords from electrical outlets and disconnect all cables that are connected to the computer. 2. Remove the computer cover. See “Removing the server cover” on page 33. 3. Lay the computer on its side for easier access to the system board. 4. Locate the system board and disconnect all cables connected to the system board.
Notes: a. Your microprocessor and socket might look different from the one illustrated. b. Note the orientation of the microprocessor in the socket. You can either look for the small triangle 1 on one corner of the microprocessor or note the orientation of the notches 2 on the microprocessor. This is important when installing the new microprocessor on the system board. c. Touch only the edges of the microprocessor. Do not touch the gold contacts on the bottom. d.
14. Reconnect all cables that were disconnected from the system board. What to do next: • To work with another piece of hardware, go to the appropriate section. • To complete the replacement, go to “Completing the parts replacement” on page 66.
4. Remove the old system board battery. Figure 37. Removing the old system board battery 5. Install the new system board battery. Figure 38. Installing the new system board battery 6. Reinstall the computer cover and connect the cables. See “Completing the parts replacement” on page 66. Note: When the computer is turned on for the first time after the battery is replaced, an error message might be displayed. This is normal after replacing the battery. 7. Turn on the computer and all attached devices. 8.
Note: Before replacing the system board, make sure you have a retention module for the new system board. To replace the system board, do the following: 1. Remove all media from the drives and turn off all attached devices and the computer. Then, disconnect all power cords from electrical outlets and disconnect all cables that are connected to the computer. 2. Remove the computer cover. See “Removing the server cover” on page 33. 3. Place the computer on its side to gain easier access to the system board. 4.
16. Go to “Completing the parts replacement” on page 66. The failing system board must be returned with microprocessor socket covers to protect the pins during shipping and handling. Install the microprocessor socket covers removed from the new system board on the failing system board. Note: The microprocessor socket cover installation procedure should be performed on both microprocessor sockets on the failing system board. To install a microprocessor socket cover, do the following: 1.
Completing the parts replacement After completing the installation or replacement for all parts, you need to reinstall the server cover and reconnect cables. To reinstall the server cover and reconnect cables to your server, do the following: 1. Make sure that all components have been reassembled correctly and that no tools or loose screws are left inside your server. See “Internal components” on page 27 for the locations of various components in your server. 2.
Connecting the cables Attention: To prevent damage to equipment, connect the power cords after completing the parts replacement. If the server cables and connector panel have color-coded connections, match the color of the cable end with the color of the connector. For example, match a blue cable end with a blue panel connector, a red cable end with a red connector, and so on. See “Rear view” on page 24 for an illustration of the I/O connectors on the rear of the server.
• The integrated management module (IMM) can turn off the server as an automatic response to a critical system failure. Connecting external devices If you install a supported optional adapter, you can attach external devices to the server. To attach an external device, do the following: Note: If you are attaching an external device, see the documentation that comes with the device for information about cabling. 1.
Chapter 6. Parts listing The chapter lists the replaceable components for the ThinkServer TS130 machine types 1098, 1100, 1105, and 1106. To check for an updated parts listing on the Web, do the following: 1. Go to http://www.lenovo.com/support. 2. Click Download & Drivers ➙ ThinkServer and then follow the instructions on the Web page to download firmware updates for your server.
Table 4. Parts listing, type 1098 Item # 1098 FRUs FRU# CRU 1 Thermal kit 95 and 73 W (including heatsink, RM and mounting plate) (models CTO all models) 03X3844 1 2 Microprocessor, E3-1275 quad core / 2 GT 3.40 GHz 95 W (models CTO) 03T7050 N 2 Microprocessor, E3-1245 quad core / 2 GT 3.30 GHz 95 W (models CTO) 03T7051 N 2 Microprocessor, E3-1235 quad core / 2 GT 3.20 GHz 95 W (models CTO) 03T7052 N 2 Microprocessor, E3-1225 quad core / 2 GT 3.
Table 4.
Table 5. Parts listing, type 1100 (continued) Item # FRU# CRU Power supply, 280 Watt (80 plus bronze) (models CTO 12U 12F 12G 12M 12J 12S 12L 12D 12Y) 45J9431 2 EMC shield 5.
Table 6.
Table 6.
Table 7. Parts listing, type 1106 (continued) Item # 1106 FRUs FRU# CRU 8 System board, motherboard CPA-SX31200 V1.0, TPM enabled (models CTO 1GG 1HG 1EU 1EF 1EM 1EJ A1G 1ES 1EL 1ED 1EY A1M) 03T8003 N 8 System board, motherboard CPA-SX31200 V1.0, TPM disabled, surge protetion (models CTO 1GG 1HG 1EU 1EF 1EM 1EJ A1G 1ES 1EL 1ED 1EY A1M) 03X3754 N 10 Power supply, 280 Watt (80 plus bronze) (models CTO 1GG 1HG 1EU 1EF 1EM 1EJ A1G 1ES 1EL 1ED 1EY) 45J9431 2 EMC shield 5.
Table 9.
Table 12.
Table 14.
Table 15.
Table 17.
Table 19.
82 ThinkServer TS130 Hardware Maintenance Manual
Chapter 7. Configuring the server The following configuration programs come with the server: • Setup Utility The Setup Utility program is part of the server firmware. You can use the Setup Utility program to view your server configuration, change the startup device sequence, set the date and time, and set passwords. For information about using this program, see “Using the Setup Utility program” on page 83.
• Lenovo provides the BIOS update utility on the Lenovo Web site. You can download the BIOS image and follow the instructions on the Web site to update the BIOS. See “Updating system programs” on page 102. After updating the BIOS, all the BIOS settings become the default settings of the updated BIOS version. You need to check and reconfigure the BIOS settings for your specific needs. • If you have changed any hardware in the server, you might need to reflash the BIOS and the RDX. Table 20.
Table 22. Submenus under the System Summary menu Item Option or description CPU Type Show the CPU brand and CPU type. CPU Speed Show the CPU speed. CPU Core Count Installed Memory Show the total size of memory installed on the system board.
Table 25. Submenus under the Serial Port Setup menu Item Serial Port1 Address Option Disabled, [3F8/IRQ4], 2F8/IRQ3, 3E8/IRQ4, 2E8/IRQ3 Description Disable or select settings for Serial Port 1. Note: [ ] indicates the default setting. Table 26. Submenus under the USB Setup menu Item Option Description USB Support [Enabled] / Disabled Enable or disable USB functions. If it is disabled, no USB device can be used. USB Legacy Support [Enabled] / Disabled Enable or disable the USB legacy support.
Table 27. Submenus under the ATA Drive Setup menu (continued) Item Hard Disk Pre-delay Option Description [Disabled] / 3 Seconds / 6 Seconds / 9 Seconds / 12 Seconds / 15 Seconds / 21 Seconds / 30 Seconds Force the BIOS to delay the initialization of hard disk drives for up to 30 seconds. The delay provides your hard disk drives more time to spin up before the BIOS initializes them. Note: [ ] indicates the default setting. Table 28.
Table 30. Submenus under the Network Setup menu Item Option Description Onboard Ethernet Controller [Enabled] / Disabled Enable or disable the onboard Ethernet controller. Note: If you select Disabled, the Intel AMT related functions will be disabled. Boot Agent [PXE] / SMC / Disabled Load the onboard PXE (Preboot Execution Environment) or SMC (Secure Managed Client). This feature enables the server to boot from a server image. Note: [ ] indicates the default setting. Table 31.
Table 32. Submenus under the CPU Setup menu (continued) Item Option Description Intel® Virtualization Technology Enabled / [Disabled] Enable or disable the Intel Virtualization technology. This technology can provide additional capacity for hardware computing. If you set this feature to Enabled, you have to turn off the server and disconnect the power cord from electrical outlet, and then reconnect the power cord and turn on the server to have this feature take effect.
Table 33. Submenus under the Intel® Manageability menu Item Intel® Manageability Control Option [Enabled] / Disabled Description Enable or disable Intel Manageability Control. When this function is disabled: • If the system is provisioned, MEBx (Management Engine BIOS Extension) will be unprovisioned firstly. Note: When you are prompted to unprovision MEBx, press YES. • The manageability functions will be disabled. You can go into MEBx or the BIOS to re-enable this function.
Table 35. Items under the Power menu Item After Power Loss Option Power Off / Power On / [Last State] Description This field shows whether the system will stay on after ac power is removed and then restored. • Select Power On if you are using a power strip to turn the system on. • Select Power Off if you want the system to remain off after the power is restored. • Select Last State to have the system return to the previous state.
Table 36. Submenus under the Automatic Power On menu (continued) Item Option Description Wake from Serial Port Ring [Primary] /Automatic / Disabled Enable or disable the Wake from Serial Port Ring function and controls which startup sequence to use after a serial port wake-up event. Wake from PCI Device [Primary] / Automatic / Disabled Enable or disable the Wake from PCI Device function and control which startup sequence to use after a PCI device wake-up event.
Table 37. Items under the Security menu (continued) Item Option Description Require Admin Password when Flashing Yes / [No] If No is selected, the Administrator Password will not be required when updating the system software. Require POP on Restart Yes / [No] If No is selected, the Power-On Password will only be required when the system is started with a cold boot. Hard Disk Password Enter the submenus to view all the options. See Table 38 “Submenus under the Hard Disk Password menu” on page 93.
Table 38. Submenus under the Hard Disk Password menu (continued) Item Option Require HDP on Restart Description If No is selected, the Hard Disk Password will only be required when the system is started with a cold boot. Note: It is highly recommended to set this value to Yes to achieve the highest level of security. Yes / [No] Note: [ ] indicates the default setting. Table 39.
Table 42. Items under the Startup menu Item Option Description Primary Boot Sequence This sequence is used when the system starts normally. Press the Up and Down arrow keys to select a device. Automatic Boot Sequence This sequence is used when a communication device wakes the system up. Press the Up and Down arrow keys to select a device. Error Boot Sequence This sequence is used when the BIOS determines that an error has occurred. Press the Up and Down arrow keys to select a device.
Table 42. Items under the Startup menu (continued) Item Option Option Keys Display Style [Normal] / Legacy Description Control the prompts displayed on the POST logo screen. • Normal: During the POST, this message will be displayed: To interrupt normal startup, press Enter. • Legacy: During the POST, this message will be displayed: Press F1 to enter Setup and press F12 to display Boot Menu. Startup Device Menu Prompt [Enabled] / Disabled Enable or disable the Startup Device Menu Prompt.
Password considerations A password can be any combination of up to 64 alphabetic and numeric characters. For security reasons, it is recommended to use a strong password that cannot be easily compromised.
Erasing lost or forgotten passwords (clearing CMOS) This section provides instructions on how to erase lost or forgotten passwords, such as a user password. To erase a lost or forgotten password, do the following: 1. Remove all media from the drives and turn off all attached devices and the server. Then, disconnect all power cords from electrical outlets and disconnect all cables that are connected to the server. 2. Remove the server cover. See “Removing the server cover” on page 33. 3.
Selecting a startup device If your computer does not start up from a device such as the disc or hard disk drive as expected, do one of the following to select the startup device you want. Selecting a temporary startup device Use this procedure to select a temporary startup device. Note: Not all discs and hard disk drives are bootable. 1. Turn off your computer. 2. Repeatedly press and release the F12 key when turning on the computer. When the “Please select boot device” window opens, release the F12 key.
– Two hard disk drives minimum – Improved read performance and 100% redundancy To install a secondary hard disk drive, refer to “Installing or replacing the secondary hard disk drive” on page 46. Configuring the system BIOS to enable SATA RAID functionality This section describes how to configure the system BIOS to enable SATA RAID functionality. Note: Use the arrow keys on the keyboard to make selections. To enable SATA RAID functionality, do the following: 1. Start the Setup Utility program.
• Return to step 2 to delete additional RAID volumes. • See “Creating RAID volumes” on page 100 for RAID volume creation. • Use the up and down arrow keys to select Exit and press Enter. Resetting disks to non-RAID This section describes how to reset your hard disk drives to non-RAID. To reset your hard disk drives to non-RAID, do the following: 1. Press Ctrl+I when prompted to enter the Intel Matrix Storage Manager option ROM configuration utility during system startup. 2.
6. Click Apply to begin the updates (click Cancel if you want to abort the updates and exit). All updates will run to completion, with each updater’s native user interface kept visible to the user. When the User Interface Application regains control, you will see the results screen. Before distributing the firmware update to other servers, ensure that your server can restart successfully without encountering hardware problems. Notes: 1.
Utility program by starting your computer with a system-program-update disc or running a special update program from your operating system. Lenovo might make changes and enhancements to the POST and BIOS. When updates are released, they are available as downloadable files on the Lenovo Web site at http://www.lenovo.com. Instructions for using the POST and BIOS updates are available in a TXT file that is included with the update files.
Recovering from a POST and BIOS update failure If the power to your computer is interrupted while the POST and BIOS are being updated, your computer might not restart correctly. If this happens, perform the following procedure to recover from the POST and BIOS update failure. This procedure is commonly called Boot-block Recovery. 1. Remove all media from the drives and turn off all attached devices and the computer.
Appendix A. Information resources You can use the information in this appendix to access useful resources relating to your computing needs. Safety and Warranty The Safety Information and the Warranty and Support Information at http://www.lenovo.com/support contain information on safety, setup, warranty, and notices. Read and understand all safety information before using this product. Lenovo Web site (http://www.lenovo.
106 ThinkServer TS130 Hardware Maintenance Manual
Appendix B. Help and service This appendix contains information about obtaining help and service. Using the documentation If you experience a problem with your computer, see Chapter 3 “Diagnostics and troubleshooting” on page 13. For information on additional resources to help you troubleshoot your computer problem, see Appendix A “Information resources” on page 105.
• • • • Serial numbers of your hardware products Description of the problem Exact wording of any error messages Hardware and software configuration information Using other services If you travel with your computer or relocate it to a country where your desktop or notebook computer machine type is sold, your computer might be eligible for International Warranty Service, which automatically entitles you to obtain warranty service throughout the warranty period.
Appendix C. Notices Lenovo may not offer the products, services, or features discussed in this document in all countries. Consult your local Lenovo representative for information on the products and services currently available in your area. Any reference to a Lenovo product, program, or service is not intended to state or imply that only that Lenovo product, program, or service may be used.
Trademarks The following terms are trademarks of Lenovo in the United States, other countries, or both: Lenovo The Lenovo logo ThinkServer Microsoft, Windows, and Windows Server are trademarks of the Microsoft group of companies. Intel and Intel SpeedStep are trademarks of Intel Corporation in the United States, other countries, or both. Other company, product, or service names may be trademarks or service marks of others.
Collecting and recycling a disused Lenovo computer or monitor If you are a company employee and need to dispose of a Lenovo computer or monitor that is the property of the company, you must do so in accordance with the Law for Promotion of Effective Utilization of Resources. Computers and monitors are categorized as industrial waste and should be properly disposed of by an industrial waste disposal contractor certified by a local government.
For the European Union: Notice: This mark applies only to countries within the European Union (EU). Batteries or packaging for batteries are labeled in accordance with European Directive 2006/66/EC concerning batteries and accumulators and waste batteries and accumulators. The Directive determines the framework for the return and recycling of used batteries and accumulators as applicable throughout the European Union.
levels or concentrations of harmful gases include damage that might cause the server to malfunction or cease functioning altogether. This specification sets forth limits for particulates and gases that are intended to avoid such damage. The limits must not be viewed or used as definitive limits, because numerous other factors, such as temperature or moisture content of the air, can influence the impact of particulates or environmental corrosives and gaseous contaminant transfer.
Le marquage des déchets d'équipements électriques et électroniques (DEEE) s'applique uniquement aux pays de l'Union européenne (EU) et à la Norvège. Les appareils sont marqués conformément à la Directive 2002/96/CE du Conseil Européen relative aux déchets d'équipements électriques et électroniques (DEEE). Cette directive, applicable à l'ensemble des pays de l'Union européenne, concerne la collecte et le recyclage des appareils usagés.
deverá ser aposta em diversos produtos para indicar que os mesmos não poderão ser deitados fora, mas sim recuperados no final da respectiva vida útil, de acordo com a referida Directiva.
Restriction of Hazardous Substances Directive (RoHS) This topic provides statements about the Restriction of Hazardous Substances Directive (RoHS).
China RoHS Turkish statement of compliance The Lenovo product meets the requirements of the Republic of Turkey Directive on the Restriction of the Use of Certain Hazardous Substances in Electrical and Electronic Equipment (EEE). Appendix C.
Ukraine RoHS German Ordinance for Work gloss statement The product is not suitable for use with visual display work place devices according to clause 2 of the German Ordinance for Work with Visual Display Units. Das Produkt ist nicht für den Einsatz an Bildschirmarbeitsplätzen im Sinne § 2 der Bildschirmarbeitsverordnung geeignet. Electronic emission notices This topic includes electronic emission notices.
This product is in conformity with the protection requirements of EU Council Directive 2004/108/EC on the approximation of the laws of the Member States relating to electromagnetic compatibility. Lenovo cannot accept responsibility for any failure to satisfy the protection requirements resulting from a non-recommended modification of the product, including the installation of option cards from other manufacturers.
Japan VCCI Class B compliance statement Japan compliance statement for products which connect to the power mains with rated current less than or equal to 20 A per phase Lenovo product service information for Taiwan 120 ThinkServer TS130 Hardware Maintenance Manual
Index A Ethernet connector 25 exiting, Setup Utility 99 expansion 10 Administrator, password 97 audio line-in connector 25 audio line-out connector 25 availability 11 F failure, recovering from POST/BIOS features 9 field replaceable units (FRUs) 69 firmware, updating 101 flashing the BIOS 103 front bezel front bezel, removing 34, 54 front bezel, reinstalling 34, 54 front connectors 23 front fan assembly, replacing 55 B basic guidelines 29 basic troubleshooting 15 boot-block recovery 104 C cables rear c
installing, removing system board 39 Microphone connector microprocessor replacing 59 specifications 10 S 39 25 N notices 109 O optical drive, replacing 41 P particulate contamination 112 parts listing 69 parts replacement, completing 66 password Administrator 97 considerations 97 Power-On Password 97 setting, changing, deleting 97 passwords erasing 98 lost or forgotten 98 passwords, using 96 PCI card 35 installing, replacing 35 slots 35 power cords 76 power supply 10 power supply assembly, replacing
U updating (flashing) the BIOS 103 server configuration 83 system programs 102 updating (flashing) the BIOS 103 updating firmware 101 USB connector 25 using diagnostic programs 107 documentation 107 EasyStartup 102 other services 108 passwords 96 Setup Utility 83 V VGA monitor connector 25 video subsystem 10 viewing and changing settings 96 W warranty information 105 Web site Lenovo support 29, 69 working inside the server with the power on © Copyright Lenovo 2011 31 123
124 ThinkServer TS130 Hardware Maintenance Manual
