ThinkServer TS440 Hardware Maintenance Manual Machine Types: 70AL, 70AM, 70AN, and 70AQ
Note: Before using the information and the product it supports, be sure to read and understand the following: • The Read Me First that comes with your product • “Safety information” on page iii • Appendix A “Notices” on page 177 Third Edition (May 2014) © Copyright Lenovo 2013, 2014. LIMITED AND RESTRICTED RIGHTS NOTICE: If data or software is delivered pursuant a General Services Administration “GSA” contract, use, reproduction, or disclosure is subject to restrictions set forth in Contract No.
Contents Safety information . . . . . . . . . . Products that are not assessed . . . . . . . . . iii x Chapter 1. General information . . . . . 1 Introduction . . . . . . . . . . . . . . . . . Server documentation . . . . . . . . . . . . . 1 2 Chapter 2. Server setup road map . . . 5 Chapter 3. Product overview . . . . . . 7 Server package . . . . . . . . . . . . . Features . . . . . . . . . . . . . . . . Specifications . . . . . . . . . . . . . . Software . . . . . . . . . . . . . . . .
Replacing the power distribution board and cage assembly . . . . . . . . . . . . . Replacing the power conversion board . . . Replacing the hot-swap hard-disk-drive backplane. . . . . . . . . . . . . . . Replacing the non-hot-swap power supply assembly . . . . . . . . . . . . . . . Replacing the cover presence switch . . . . Replacing the front panel board assembly . . Replacing the front system fan 1 . . . . . . Replacing the rear system fan . . . . . . . Replacing the heat sink and fan assembly . .
Safety information Note: Before using the product, be sure to read and understand the multilingual safety instructions on the documentation DVD that comes with the product. Antes de usar o produto, leia e entenda as instruções de segurança multilíngues no DVD de documentação que o acompanha. Преди да използвате този продукт, задължително прочетете и вникнете в многоезичните инструкции за безопасност в DVD диска с документация, който се предоставя с продукта.
Przed skorzystaniem z produktu należy zapoznać się z wielojęzycznymi instrukcjami bezpieczeństwa znajdującymi się na płycie DVD z dokumentacją dostarczoną wraz z produktem. Antes de utilizar o produto, leia atentamente as instruções de segurança multilingues que constam no DVD de documentação fornecido com o produto. Înainte de a utiliza produsul, asiguraţi-vă că aţi citit şi înţeles instrucţiunile de siguranţă în mai multe limbi de pe DVD-ul cu documentaţie care însoţeşte produsul.
Statement 1 DANGER Electrical current from power, telephone, and communication cables is hazardous. To avoid a shock hazard: • Do not connect or disconnect any cables or perform installation, maintenance, or reconfiguration of this product during an electrical storm. • Connect all power cords to a properly wired and grounded electrical outlet. • Ensure that all power cord connectors are securely and completely plugged into receptacles.
Statement 3 CAUTION: When laser products (such as CD-ROMs, DVD drives, fiber optic devices, or transmitters) are installed, note the following: • Do not remove the covers. Removing the covers of the laser product could result in exposure to hazardous laser radiation. There are no serviceable parts inside the device. • Use of controls or adjustments or performance of procedures other than those specified herein might result in hazardous radiation exposure.
Statement 6 CAUTION: If you install a strain-relief bracket option over the end of the power cord that is connected to the device, you must connect the other end of the power cord to a power source that is easily accessible in case it needs to be disconnected. Statement 7 CAUTION: If the device has doors, ensure that you remove or secure the doors before moving or lifting the device to protect against personal injury. The doors will not support the weight of the device.
Statement 11 CAUTION: The following label indicates a potential heat hazard. Statement 12 DANGER Overloading a branch circuit is a potential fire hazard and a shock hazard under certain conditions. To avoid these hazards, ensure that your system electrical requirements do not exceed branch current ratings at the installation site. Statement 13 CAUTION: Ensure that the rack is secured properly to avoid tipping when the server unit is extended on the rails.
Statement 16 CAUTION: To reduce the risk of electric shock or energy hazards: • This equipment must be installed by trained service personnel in a restricted-access location, as defined by your local electrical code and the latest edition of IEC 60950. • Connect the equipment to a reliably earthed safety extra low voltage (SELV) source. An SELV source is a secondary circuit that is designed so that normal and single fault conditions do not cause the voltages to exceed a safe level (60 V direct current).
Statement 20 CAUTION: A lithium ion battery is provided. To avoid possible explosion, do not burn the battery. Replace the battery only with the Lenovo-approved part. Recycle or discard the battery as instructed by local regulations.
Chapter 1. General information This chapter provides some general information about your product. This chapter contains the following items: • “Introduction” on page 1 • “Server documentation” on page 2 Introduction This user guide for your Lenovo® ThinkServer® product contains information about the server features, specifications, component locations, configuration instructions, hardware replacement procedures, and basic troubleshooting and diagnostics.
Record information about your server in the following table. You will need the information if you ever need to have your server serviced. For where to find the product information label on the chassis, see “Machine type, model, and serial number label” on page 12.
Note: Lenovo maintains pages on the World Wide Web where you can get the latest technical information and download documentation or device drivers and updates. Some information in the documents on the documentation DVD might change without notice after the first release of the DVD. You can always obtain all the most up-to-date documentation for your server from the Lenovo Web site at: http://www.lenovo.
4 ThinkServer TS440 Hardware Maintenance Manual
Chapter 2. Server setup road map This chapter provides a general road map to guide you through setting up your server. The server setup procedure varies depending on the configuration of the server when it was delivered. In some cases, the server is fully configured and you need to connect the server to the network and an ac power source, and then you can turn on the server.
6 ThinkServer TS440 Hardware Maintenance Manual
Chapter 3. Product overview This chapter provides information about the server package, features, specifications, software programs, and component locations. This chapter contains the following items: • “Server package” on page 7 • “Features” on page 7 • “Specifications” on page 11 • “Software” on page 11 • “Locations” on page 12 Server package The server package includes the server, power cords, printed documentation, a documentation DVD, and software media.
refer to the Personal Systems Reference document for ThinkServer products at: http://www.lenovo.com/psref/ Microprocessor One Intel® Xeon® microprocessor (internal cache size varies by model) For a list of ThinkServer microprocessor options, go to: http://www.lenovo.com/thinkserver Memory Your server has four memory slots. For more information, see “Memory module installation rules” on page 74.
Note: If the server has only one optical drive installed, ensure that the optical drive is installed in the lower bay (optical drive bay 1). The upper bay is for a secondary optical drive only. • RDX drive Your server supports internal RDX drives that enable you to store data on RDX media. An internal RDX drive is installed in the optical drive bay 2. To install or remove an internal RDX drive, see “Installing or replacing an internal RDX drive” on page 103.
– Ability to store the power-on self-test (POST) hardware test results – BIOS Setup Utility program The BIOS Setup Utility program helps you view the server information and configure the server in the pre-operating system environment. See “Using the Setup Utility program” on page 47. – Hot-swap feature Some models support hot-swap hard disk drives and hot-swap redundant power supplies.
Specifications This topic lists the physical specifications for your server. Dimensions Width: 195 mm (7.68 inches) Height: 430 mm (16.93 inches) without foot stands; 445 mm (17.52 inches) with foot stands Depth: 595 mm (23.43 inches) including the front bezel Weight The product weight varies depending on different system configurations. Range of product weight without package: 19 kg (41.89 lb) to 28 kg (61.73 lb) Range of product package weight: 2.8 kg (6.17 lb) to 3.5 kg (7.
BIOS update utilities The BIOS firmware keeps updating after the shipment of the server. Lenovo maintains pages on the Support Web site and provides the BIOS update utilities with instructions for download to help you update the BIOS if needed. For more information, see “Updating or recovering the BIOS” on page 53 and “Updating the firmware” on page 62. RAID configuration utilities Your server supports onboard SATA software RAID.
The following illustration is a sample of the machine type, model, and serial number labels on the server. Note: Depending on the model, your server might look slightly different from the illustration in this topic. MT-M XXXX -XXX S/N XXXXXXX X 1 MT-M XXXX -XXX S/N XXXXXXX X X -X XX X M X XX MT- XXXX S/N Figure 2. Machine type, model, and serial number labels Chapter 3.
Front view of the server This topic provides information to help you locate the parts on the front of the server. The following illustration shows the front view of the server. Figure 3.
4 Optical drive eject/close button Press this button to eject or close the optical drive when the server power is on. 5 Optical drive status LED The optical drive status LED is blinking in green when the optical drive is working or in the POST process. 6 Front door 7 Front door lock You can lock the front door to protect the hard-disk-drive cages from unauthorized access. 8 Front door handle Use the front door handle to open the front door. Chapter 3.
Front panel This topic provides information to help you locate the control, connectors, and LEDs on the front panel of the server. The following illustration shows the control, connectors, and LEDs on the front panel of the server. Note: Depending on the model, your server might look slightly different from the following illustration. Figure 4. Front panel 1 Power button with power status LED 4 Front USB 3.0 connector 1 2 Hard-disk-drive status LED 5 Front USB 3.
2 Power status LED Color Description On Green The server is on. Off None The server is off. Hard-disk-drive status LED The hard-disk-drive status LED helps you to determine the status of the hard-disk-drive activity. Note: The hard-disk-drive status LED is available on server models without a discrete RAID card installed. 3 Hard-disk-drive status LED Color Description Off None The hard disk drive is not in use. Blinking Green The hard disk drive is active and data is being transferred.
Figure 5. Rear view of the server with a non-hot-swap power supply assembly 1 Power cord connector 5 USB 2.0 connectors (2) 2 Serial connector 6 Expansion card area 3 VGA DB-15 connector 7 Ethernet connector (RJ-45) 4 USB 3.
Your server model might have one or two hot-swap redundant power supplies. Each hot-swap redundant power supply has one power cord connector 1 on the rear of the server. For each hot-swap redundant power supply, there might be one or two status LEDs on the power supply near the power cord connector. When the LED is lit in green, it indicates that the hot-swap redundant power supply is working correctly.
6 Expansion card area Your server has four expansion slots on the system board for you to install appropriate Peripheral Component Interconnect (PCI) cards or PCI Express cards. For detailed information, see “System board components” on page 39. Note: If a ThinkServer Host Bus Adapter (HBA) is available, refer to its user guide and the below table for detailed information. The user guide is available for download at: http://www.lenovo.com/UserManuals Table 1.
Padlock Your server comes with a padlock loop. When a padlock is installed, the server cover cannot be removed. Figure 7. Padlock Chapter 3.
Kensington-style cable lock You can use a Kensington-style cable lock to secure your server to a desk, table, or other non-permanent fixture. The cable lock attaches to the security-lock slot at the rear of your server and is operated with a key or combination depending on the type selected. The cable lock also locks the server cover. This is the same type of lock used with many notebook computers. You can order such a cable lock directly from Lenovo by searching for Kensington at: http://www.lenovo.
Front door lock You can remove the key attached on the rear of the server and use it to open or lock the front door of the server. The front door protects the hard-disk-drive cages and prevents unauthorized access to the installed hard disk drives. Figure 9. Front door lock Server components This topic provides information to help you locate the components of your server. For more information about major components, see the related topics in “Locations” on page 12.
Components of server models with four 3.5-inch hot-swap hard-disk-drive bays Figure 10. Components of server models with four 3.
Components of server models with eight 3.5-inch hot-swap hard-disk-drive bays Figure 11. Components of server models with eight 3.
Components of server models with eight 2.5-inch hot-swap hard-disk-drive bays Figure 12. Components of server models with eight 2.
Components of server models with four 3.5-inch non-hot-swap hard-disk-drive bays Figure 13. Components of server models with four 3.
might require some technical skills or tools, or request that a technician install the optional-service CRU under the terms of the applicable warranty service type for your country or region. Non-CRUs must be replaced only by trained service technicians. The following table lists the major FRUs in your server and the CRU identification information. For a complete listing of FRU information, such as FRU part numbers and supported server models, go to: http://www.lenovo.
Figure 14. 3.5-inch hot-swap hard-disk-drive status LEDs Chapter 3.
Figure 15. 2.5-inch hot-swap hard-disk-drive status LEDs 1 Hard-disk-drive activity LED 2 Hard-disk-drive RAID status LED Description Off Off The hard disk drive has failed or is not present. On, green Off The hard disk drive is present but not in use. Blinking, green Off The hard disk drive is active and data is being transferred. On, green Blinking rapidly (about four flashes per second), amber The RAID controller is locating the hard disk drive.
Some server models come with a required RAID card to provide advanced SATA/SAS hardware RAID functions to the server. If your server does not come with a RAID card, you can purchase one from Lenovo. See “Installing or removing the RAID card” on page 82. Notes: • The option kit for the RAID card is designed for different types of servers and might contain additional cables that are not required for your server.
ThinkServer RAID 700 Adapter The following illustration shows the connectors on the ThinkServer RAID 700 Adapter. Figure 17. ThinkServer RAID 700 Adapter 1 Ports 7-4 3 ThinkServer RAID 700 Battery connector 2 Ports 3-0 1 Ports 7-4 Used to connect a mini-SAS signal cable. See “Connecting the cables” on page 36. 2 Ports 3-0 Used to connect a mini-SAS signal cable. See “Connecting the cables” on page 36. 3 ThinkServer RAID 700 Battery connector Used to connect a ThinkServer RAID 700 Battery.
The following illustration shows the locations of the hot-swap hard-disk-drive backplanes 1 . You need to open the server cover and remove the front system fans to access the backplanes. See “Removing the server cover” on page 67 and “Replacing the front system fan 1” on page 144. Notes: • Depending on the model, your server might look slightly different from the illustration in this topic. • The following illustration is based on server models that have five to eight 3.
The following illustrations show the connectors on the backplane for server models with four 3.5-inch hot-swap hard-disk-drive bays. Figure 19. Front view of the backplane for server models with four 3.5-inch hot-swap hard-disk-drive bays 1 Slot 0 for a 3.5-inch SATA or SAS hot-swap hard disk drive 3 Slot 2 for a 3.5-inch SATA or SAS hot-swap hard disk drive 2 Slot 1 for a 3.5-inch SATA or SAS hot-swap hard disk drive 4 Slot 3 for a 3.5-inch SATA or SAS hot-swap hard disk drive Figure 20.
Backplane for server models with eight 2.5-inch hot-swap hard-disk-drive bays This topic provides information to help you locate the connectors on the backplane for server models with eight 2.5-inch hot-swap hard-disk-drive bays. The following illustrations show the connectors on the backplane for server models with eight 2.5-inch hot-swap hard-disk-drive bays. Figure 21. Front view of the backplane for server models with eight 2.5-inch hot-swap hard-disk-drive bays 1 Slot 0 for a 2.
2 Mini-SAS signal cable connector 1 Used to connect the mini-SAS connector on one end of the mini-SAS signal cable. 3 Mini-SAS signal cable connector 0 Used to connect the mini-SAS connector on one end of the mini-SAS signal cable. Connecting the cables This topic provides instructions on the following cable connections: • “Connecting the mini-SAS signal cable from the system board to the backplane for server models with hot-swap hard disk drives” on page 36.
Note: The number on the label for each of the four SATA signal cables indicates the sequence to follow when you are connecting the cables to the corresponding SATA connectors (0-3) on the system board.
Figure 24. Connecting cables from the RAID card to the backplanes To connect the mini-SAS signal cables from the RAID card to the backplanes, do the following: • If you are using a ThinkServer RAID 700 Adapter, do the following: 1. Use one mini-SAS to mini-SAS signal cable. Connect the mini-SAS connector 3 on one end of the cable to the ports 3-0 on the RAID card. Then, connect the mini-SAS connector 4 on the other end of the cable to the mini-SAS signal cable connector 0 on the backplane for 2.
To connect the power cables, do the following: • For server models with up to four 3.5-inch hot-swap hard disk drives, connect the 4-pin power connector on one end of the power cable to the 4-pin power connector on the system board. Then, connect the other power connector on the other end of the power cable to the power connector on the backplane. • For server models with more than four 3.5-inch hot-swap hard disk drives, use two power cables.
33 32 31 Figure 25. System board components 1 4-pin power connector 18 SATA connector 2 2 System board battery 19 System fan 1 connector 3 Microprocessor socket 20 Front panel connector 4 Microprocessor fan connector 21 Front USB 3.0 connector 5 Memory slot 1 (DIMM1) 22 Platform Controller Hub (PCH) 6 Memory slot 2 (DIMM2) 23 SATA SGPIO connector 7 Memory slot 3 (DIMM3) 24 USB 2.
1 4-pin power connector Used to connect the power cable from the power supply. 2 System board battery Your server has a special type of memory that maintains the date, time, and configuration information for built-in features. The system board battery keeps the information active when you turn off the server. 3 Microprocessor socket The microprocessor is secured in the microprocessor socket on the system board. A heat sink and fan assembly is installed above the microprocessor to provide cooling.
19 System fan 1 connector Used to connect the cable of the lower front system fan (front system fan 1). 20 Front panel connector Used to connect the front panel cable. 21 Front USB 3.0 connector Used to connect the front USB cable. 22 Platform Controller Hub (PCH) This chip provides the data buffering and interface arbitration required to ensure that system interfaces operate efficiently and provides the bandwidth necessary for the system to achieve peak performance.
25 Clear CMOS (Complementary Metal Oxide Semiconductor) jumper Used to clear CMOS and turn the BIOS settings into the factory default settings. Note: Clearing CMOS does not erase your BIOS passwords. A jumper is a short length of conductor used to set up or adjust a printed circuit board, such as the system board of a computer. A jumper usually is encased in a non-conductive block of plastic for convenient use and to avoid any possible damage to a live circuit.
29 PCI Express x4 card slot (PCI-E slot 3) This PCI card slot supports a PCI Express x4 card with 167 mm (6.57 inches) in length, such as an Ethernet card. 30 PCI Express x1 card slot (PCI-E slot 2) This PCI card slot supports a PCI Express x1 card with 167 mm (6.57 inches) in length, such as a graphics card. 31 PCI Express x16 card slot (PCI-E slot 1) This PCI card slot supports a PCI Express x16 card with 167 mm (6.57 inches) in length, such as an Ethernet card, a HBA, or a RAID card.
Chapter 4. Turning on and turning off the server This chapter provides information about turning on and turning off the server. Turning on the server After you finish unpacking and setting up the server, connect it to an ac power source. Press the power button on the front panel to turn on the server. See “Front panel” on page 16. Turning off the server CAUTION: The power control button on the device and the power switch on the power supply do not turn off the electrical current supplied to the device.
46 ThinkServer TS440 Hardware Maintenance Manual
Chapter 5. Configuring the server This chapter provides the following information to help you configure the server: • “Using the Setup Utility program” on page 47 • “Using the ThinkServer EasyStartup program” on page 54 • “Configuring RAID” on page 57 • “Configuring the Ethernet controllers” on page 62 • “Updating the firmware” on page 62 Using the Setup Utility program This topic provides information about using the Setup Utility program. The Setup Utility program is part of the server firmware.
Notes: • The default settings already are optimized for you. Use the default value for any item you are not familiar with. Do not change the value of unfamiliar items to avoid unexpected problems. If you consider changing the server configuration, proceed with extreme caution. Setting the configuration incorrectly might cause unexpected results. If you cannot turn on the server because of incorrect BIOS settings, use the Clear CMOS jumper to restore the BIOS settings to the factory default settings.
Notes: • Enabled means that the function is configured. • Disabled means that the function is not configured. The Advanced menu contains the following submenus. For more information, enter the corresponding submenu and refer to the instructions on the screen. • CPU Setup: View and set CPU configuration parameters. • Intel® Manageability: View and set Intel vPRO features. Power menu You can view or change various server power management settings on the Power menu in the Setup Utility program.
• Secure Boot: View and set secure boot configuration parameters. Startup menu The Startup menu in the Setup Utility program provides an interface to help you view or change the server startup options, including the startup sequence and boot priority for various devices. After the server restarts, changes in the startup options take effect. The startup sequence specifies the order in which the server checks devices to find a boot record. The server starts from the first boot record that it finds.
The Exit menu contains the following items: • Save Changes and Exit: Save changes and exit the Setup Utility program. • Discard Changes and Exit: Discard changes, load previous values, and then exit the Setup Utility program. • Load Optimal Defaults: Restore the user default values for all the items. • OS Optimized Defaults: Select Enabled to meet the Microsoft Windows 8 certification requirement.
• Have at least eight characters in length • Contain at least one alphabetic character and one numeric character • Not be your name or your user name • Not be a common word or a common name • Be significantly different from your previous passwords Besides the alphabetic characters (a-z) and numeric characters (0-9), the server also supports characters typed using special keys on the keyboard for a password.
1. Turn on or restart your server. 2. When you see the logo screen, press F12 to display the boot menu. The boot device selection window opens. 3. In the boot device selection window, use the up and down arrow keys on the keyboard to switch between the selections. Press Enter to select the device of your choice. Then, the server will start up from the selected device. • To view or permanently change the configured startup device sequence, do the following: 1. Start the Setup Utility program.
• Downgrading the BIOS to an earlier version is not recommended and might not be supported. An earlier BIOS version might not contain the support for the latest system configurations. • If the power to your server is interrupted while the POST and BIOS are being updated, your server might not restart correctly. Ensure that you perform the BIOS update procedure in an environment with a steady power supply. Besides, ensure that your server can restart successfully without encountering hardware problems.
• Device drivers provided based on the server model and detected devices • Ability to download device drivers from the ThinkServer EasyStartup DVD according to the operating system or add-on device • Selectable partition size and file system type • Support for multiple operating systems • Ability to install the operating system and device drivers in an unattended mode to save time • Ability to create a reusable response file that can be used with similarly configured Lenovo servers to make future installati
The ThinkServer EasyStartup program main interface provides the following menus on the left pane of the screen: • Home This menu is the welcome page that contains some general descriptions about the program and the Lenovo copyright and trademark statements. • Compatibility notes This menu provides information about the RAID controllers, operating systems, and server configurations supported by the version of the program you are using.
• View a general introduction to your ThinkServer server model and the specific server configuration information. • View general guidance on how to use the ThinkServer EasyStartup DVD. • Download the required device drivers to a removable storage device so that you can easily get the drivers for server configuration when you need them, especially when you finish installing an operating system without using the ThinkServer EasyStartup DVD and need appropriate device drivers to configure your server.
• RAID 0: block-level striping without parity or mirroring Simple stripe sets are normally referred to as RAID 0. RAID 0 uses striping to provide high data throughput, especially for large files in an environment that does not require fault tolerance. RAID 0 has no redundancy and it provides improved performance and additional storage without fault tolerance. Any drive failure destroys the array and the likelihood of failure increases with more drives in the array.
Note: Before configuring RAID for your server, ensure that you use hard disk drives that are of the same type (SATA or SAS) and have the same capacity within a single RAID array. Your server supports the following two types of RAID configurations: • Onboard SATA software RAID configuration using the Intel Rapid Storage Technology enterprise program The onboard SATA software RAID controller is integrated on the Intel C220 chip on the system board.
Creating RAID volumes This section describes how to use the Intel Rapid Storage Technology enterprise option ROM configuration utility to create RAID volumes. To create RAID volumes, do the following: 1. Press Ctrl+I when prompted to enter the Intel Rapid Storage Technology enterprise option ROM configuration utility during system startup. 2. Use the up and down arrow keys to select Create RAID Volume and press Enter. 3. Type a proper RAID volume name in the Name field and press Tab. 4.
Configuring the advanced SATA or SAS hardware RAID Some server models come with a required RAID card to provide advanced SATA/SAS hardware RAID functions to the server. You also can purchase the RAID card from Lenovo and install it into server models that support the RAID card to get advanced SATA/SAS hardware RAID functions. See “RAID card” on page 30 and “Installing or removing the RAID card” on page 82 for more information.
using the MegaRAID Storage Manager program” on page 62 and “Configuring the advanced SATA or SAS hardware RAID” on page 61. Installing and using the MegaRAID Storage Manager program You can install and use the MegaRAID Storage Manager program to manage the RAID array and RAID controller in an operating system environment after configuring RAID. The installation package for the MegaRAID Storage Manager program is on the ThinkServer EasyStartup DVD.
Using the Firmware Updater program The Firmware Updater program enables you to maintain your system firmware up-to-date and helps you avoid unnecessary outages. To update your system firmware using the Firmware Updater program, do the following: Note: Before distributing the firmware updates to a server, ensure that your server can restart successfully without encountering hardware problems. 1. Go to http://www.lenovo.
64 ThinkServer TS440 Hardware Maintenance Manual
Chapter 6. Installing, removing, or replacing hardware This chapter provides instructions on how to install, remove, or replace hardware for your server.
• Back up all important data before you make changes to drives. • Have a small flat-blade screwdriver available. • You do not have to turn off the server to install or replace a hot-swap redundant power supply, hot-swap hard disk drives, or hot-plug USB devices. However, you must turn off the server before performing any steps that involve installing, removing, or replacing adapter cables or non-hot-swap devices or components.
• Ensure that you replace a failing fan within 48 hours. • When replacing a hot-swap drive, install the new hot-swap drive within two minutes of removal. Working inside the server with the power on Attention: Static electricity that is released to internal server components when the server is turned on might cause the server to halt, which might result in the loss of data.
5. Loosen the thumbscrew that secures the server cover, and then slide the server cover to the rear until it is stopped. Notes: a. The server cover is securely installed and you need to use a tool, such as a screwdriver, to loosen the thumbscrew that secures the server cover. The thumbscrew is an integrated part of the server cover. Do not try to remove the thumbscrew from the server cover. b. It is recommended that you wait three to five minutes to let the server cool before removing the server cover.
6. Pivot the server cover outward to remove it. Figure 27. Removing the server cover Attention: For proper cooling and airflow, install the server cover before turning on the server. Operating the server for more than 30 minutes with the server cover removed might damage server components. To reinstall the server cover, see “Reinstalling the server cover and reconnecting cables” on page 163.
3. Remove the front bezel by releasing the three plastic tabs on the left side and pivoting the front bezel outward. Figure 28.
4. To reinstall the front bezel, align the other three plastic tabs on the right side of the front bezel with the corresponding holes in the chassis, then pivot the front bezel inward until it snaps into position on the left side. Figure 29. Installing the front bezel 5. Go to “Completing the parts replacement” on page 163.
a. Press the release tab 1 in the direction as shown, and then carefully lift the PCI card bracket assembly slightly upward until each of the two retention posts 2 on the chassis is in the central position of the corresponding hole in the PCI card bracket assembly. Figure 30. Releasing the PCI card bracket assembly b. Carefully move the PCI card bracket assembly to the top side of the chassis until the PCI card bracket assembly is released from the retention posts on the chassis.
5. Reinstall the PCI card bracket assembly by doing the following: a. Install the small low-profile PCI card bracket into the main PCI card bracket as shown. Figure 32. Installing the small low-profile PCI card bracket into the main PCI card bracket b. Place the PCI card bracket assembly into the chassis so that the two retention posts 2 on the bottom of the chassis are inserted into the corresponding holes in the PCI card bracket assembly.
6. Go to “Completing the parts replacement” on page 163. Installing, removing, or replacing hardware This topic provides instructions on how to install, remove, or replace hardware for your server. You can expand the capabilities of your server by adding new hardware devices, such as memory modules, PCI cards, or other server options, and maintain your server by replacing the failing hardware devices.
The following illustration shows the locations of all memory slots on the system board. Figure 34. Memory slots on the system board 1 Memory slot (DIMM1) 3 Memory slot (DIMM3) 2 Memory slot (DIMM2) 4 Memory slot (DIMM4) The following table explains the memory module installation rules for your server. The “X” mark indicates the memory slots into which the memory modules should be installed in different situations. Table 2.
Notes: • To optimize system performance, ensure that you consider and follow the memory module installation rules when performing the operation. See “Memory module installation rules” on page 74. • Use any documentation that comes with the memory module and follow those instructions in addition to the instructions in this topic. To install a memory module, do the following: 1. Remove all media from the drives and turn off all attached devices and the server.
8. Position the new memory module over the memory slot. Ensure that the notch 1 on the new memory module is aligned with the key 2 in the memory slot. Then, press the new memory module straight down into the memory slot until the retaining clips close and the new memory module snaps into position. Note: If there is a gap between the memory module and the retaining clips, the memory module has not been installed correctly.
6. Locate the memory module that you want to remove and open the retaining clips on both ends of the memory slot. Then, grasp the memory module by its edges and carefully pull it straight up to remove it from the memory slot. Figure 37. Removing a memory module 7. Reconnect any cables you have disconnected. 8. If you are instructed to return the old memory module, follow all packaging instructions and use any packaging materials that are supplied to you for shipping.
1. Remove all media from the drives and turn off all attached devices and the server. Then, disconnect all power cords from electrical outlets and disconnect all cables that are connected to the server. 2. Remove the server cover. See “Removing the server cover” on page 67. 3. Lay the server on its side for easier operation. 4. If a PCI card bracket assembly is installed in your server, remove the PCI card bracket assembly. See “Removing and reinstalling the PCI card bracket assembly” on page 71. 5.
9. Position the new Ethernet card over the PCI Express card slot for which you have removed the slot bracket, and then carefully press the Ethernet card straight down until it is securely seated in the slot. Install the screw to secure the Ethernet card in place. Figure 39. Installing the Ethernet card 10. Depending on the type of the Ethernet card, you might need to connect any required cables. Refer to the documentation that comes with the Ethernet card for specific information. 11.
Removing the Ethernet card Attention: Do not open your server or attempt any repair before reading and understanding “Safety information” on page iii and “Guidelines” on page 65. This topic provides instructions on how to remove the Ethernet card. Before you begin, print all the related instructions or ensure that you can view the PDF version on another computer for reference. Notes: • Depending on the specific type, the Ethernet card might look slightly different from the illustration in this topic.
7. Remove the screw that secures the Ethernet card. Then, grasp the Ethernet card by its edges and carefully pull it out of the PCI Express card slot. Note: The Ethernet card fits tightly into the PCI Express card slot. If necessary, alternate moving each side of the Ethernet card a small and equal amount until it is completely removed from the slot. Figure 40. Removing the Ethernet card 8. Install a new Ethernet card to replace the old one or install a PCI Express card slot bracket to cover the place.
Installing the RAID card Attention: Do not open your server or attempt any repair before reading and understanding “Safety information” on page iii and “Guidelines” on page 65. This topic provides instructions on how to install the RAID card. Before you begin, print all the related instructions or ensure that you can view the PDF version on another computer for reference.
Notes: • Ensure that you back up your data before removing the RAID card because you might need to reconfigure RAID and reinstall the operating system after removing the RAID card. • If you remove the RAID card, you will lose the advanced SATA/SAS hardware RAID functions. • Use any documentation that comes with the RAID card and follow those instructions in addition to the instructions in this topic. To remove the RAID card, do the following: 1.
Installing the TR 500 key Attention: Do not open your server or attempt any repair before reading and understanding “Safety information” on page iii and “Guidelines” on page 65. This topic provides instructions on how to install the TR 500 key on a ThinkServer RAID 500 Adapter if your server has one installed. Attention: Back up your data before you begin if you want to reconfigure RAID and reinstall the operating system after installing the TR 500 Key.
8. Locate the TR 500 key connector on the ThinkServer RAID 500 Adapter and then carefully insert the TR 500 key into the connector. If necessary, you can remove the ThinkServer RAID 500 Adapter first, install the TR 500 Key on it, and then reinstall the ThinkServer RAID 500 Adapter. See “Installing or removing the RAID card” on page 82. Note: Ensure that the TR 500 key is securely seated on the ThinkServer RAID 500 Adapter. Figure 41. Installing the TR 500 key 9.
• Use any documentation that comes with the TR 500 Key and follow those instructions in addition to the instructions in this topic. To remove the TR 500 Key, do the following: 1. Remove all media from the drives and turn off all attached devices and the server. Then, disconnect all power cords from electrical outlets and disconnect all cables that are connected to the server. 2. Remove the server cover. See “Removing the server cover” on page 67. 3. Lay the server on its side for easier operation. 4.
Installing or removing the ThinkServer RAID 700 Battery This topic provides instructions on how to install or remove the ThinkServer RAID 700 Battery (hereinafter referred to as the TR 700 Battery) if your server has a ThinkServer RAID 700 Adapter installed. The TR 700 Battery protects the integrity of the cached data on the ThinkServer RAID 700 Adapter by providing backup power up to 72 hours in the case of a complete ac power failure or a brief power outage.
8. Position the TR 700 Battery above the ThinkServer RAID 700 Adapter so that the board-to-board connector 1 on the bottom of the TR 700 Battery is aligned with the connector 2 on the ThinkServer RAID 700 Adapter; and the three mounting studs on the bottom of the TR 700 Battery are aligned with the corresponding holes in the ThinkServer RAID 700 Adapter. Carefully press the TR 700 Battery onto the ThinkServer RAID 700 Adapter until the two connectors ( 1 and 2 ) are firmly joined.
Notes: • If you remove the TR 700 Battery, you will lose the backup power for the ThinkServer RAID 700 Adapter. • Use any documentation that comes with the TR 700 Battery and follow those instructions in addition to the instructions in this topic. To remove the TR 700 Battery, do the following: 1. Remove all media from the drives and turn off all attached devices and the server. Then, disconnect all power cords from electrical outlets and disconnect all cables that are connected to the server. 2.
Installing or replacing an optical drive Attention: Do not open your server or attempt any repair before reading and understanding “Safety information” on page iii and “Guidelines” on page 65. This topic provides instructions on how to install or replace an optical drive. The EMI integrity and cooling of the server are protected by having all drive bays covered or occupied. Your server has two optical drive bays.
Notes: • Depending on the model, your server might look slightly different from the illustrations in this topic. • Use any documentation that comes with the optical drive and follow those instructions in addition to the instructions in this topic. To install or replace an optical drive, do the following: 1. Remove all media from the drives and turn off all attached devices and the server. Then, disconnect all power cords from electrical outlets and disconnect all cables that are connected to the server. 2.
• If you are replacing an optical drive, disconnect the signal cable and the power cable from the rear of the optical drive. Press the release button 1 in the direction as shown and push the optical drive from the rear until it is projected from the front of the chassis. Then, hold the optical drive from the front and completely slide it out of the chassis. Figure 46. Removing the optical drive 5.
6. Slide the new optical drive into the drive bay from the front until it snaps into position. Note: You do not need to remove the front bezel when replacing an optical drive. However, if you are adding a secondary optical drive in the upper optical drive bay, you need to remove the front bezel first, and then gain access to the protective shields to remove them. The following illustration shows only the situation in which the front bezel has not been removed. Figure 47. Installing the optical drive 7.
• If you are installing an optical drive, save the removed EMI-protective shield from the chassis and plastic shield from the front bezel in case you later remove the drive and need the shields to cover the drive bay. • If you are replacing an optical drive and are instructed to return the old optical drive, follow all packaging instructions and use any packaging materials that are supplied to you for shipping. What to do next: • To work with another piece of hardware, go to the appropriate section.
1. Remove all media from the drives and turn off all attached devices and the server. Then, disconnect all power cords from electrical outlets and disconnect all cables that are connected to the server. 2. Use the front door key to unlock the front door, and then use the front door handle 1 to pivot the front door to the open position. 1 Figure 49. Opening the front door of the server 3. Remove the server cover. See “Removing the server cover” on page 67.
4. The non-hot-swap hard disk drives are installed in the lower hard-disk-drive cage and are protected by an EMI-protective panel. Press the small tab 1 on the EMI-protective panel from the bottom, and then pivot the EMI-protective panel upward to remove it from the chassis and gain access to the non-hot-swap hard-disk-drive bays. Figure 50. Removing the EMI-protective panel 5. Remove the front system fan 1. See “Replacing the front system fan 1” on page 144. 6.
8. Install the new non-hot-swap hard disk drive into a blue bracket by flexing the sides of the bracket and aligning pin 1 , pin 2 , pin 4 , and pin 5 on the bracket with the corresponding holes in the hard disk drive so that the hard disk drive can be seated in the bracket. Note: Do not touch the circuit board 3 on the bottom of the hard disk drive. Figure 51. Installing the non-hot-swap hard disk drive into the bracket 9.
13. Align the top edge of the EMI-protective panel with the top side of the hard-disk-drive cage, and then pivot the EMI-protective panel down until it snaps into position. Figure 53. Installing the EMI-protective panel 14. Close and lock the front door. What to do next: • To work with another piece of hardware, go to the appropriate section. • To complete the installation, go to “Completing the parts replacement” on page 163. Then, you might need to reconfigure RAID for your server.
Before you begin, print all the related instructions or ensure that you can view the PDF version on another computer for reference. Notes: • Depending on the model, your server might look slightly different from the illustrations in this topic. • Use any documentation that comes with the non-hot-swap hard disk drive and follow those instructions in addition to the instructions in this topic. To remove a non-hot-swap hard disk drive, do the following: 1.
4. The non-hot-swap hard disk drives are installed in the lower hard-disk-drive cage and are protected by an EMI-protective panel. Press the small tab 1 on the EMI-protective panel from the bottom, and then pivot the EMI-protective panel upward to remove it from the chassis and gain access to the non-hot-swap hard disk drives. Figure 55. Removing the EMI-protective panel 5. Remove the front system fan 1. See “Replacing the front system fan 1” on page 144. 6. Locate the non-hot-swap hard disk drive.
7. Insert two fingers into the holes in the two tabs on the front of the blue bracket. Then, press the tabs towards each other and carefully slide the non-hot-swap hard disk drive out of the front of the chassis. 1 U CP ME M U PS Figure 56. Sliding the non-hot-swap hard disk drive out of the bay 8. Flex the sides of the blue bracket to remove the non-hot-swap hard disk drive from the bracket. Save the bracket for future use. Note: Do not touch the circuit board on the hard disk drive. 9.
10. Align the top edge of the EMI-protective panel with the top side of the hard-disk-drive cage, and then pivot the EMI-protective panel down until it snaps into position. Figure 57. Installing the EMI-protective panel 11. Disconnect the SATA cable for the removed non-hot-swap hard disk drive from the system board and save the cable for future use. 12. Close and lock the front door. 13.
To install or replace an internal RDX drive, do the following: 1. Remove all media from the drives and turn off all attached devices and the server. Then, disconnect all power cords from electrical outlets and disconnect all cables that are connected to the server. 2. Remove the server cover. See “Removing the server cover” on page 67. 3. Locate the optical drive bay where you want to install or replace the RDX drive. See “Server components” on page 23. 4.
• If you are replacing an RDX drive, disconnect the signal cable and the power cable from the rear of the RDX drive. Press the release button 1 in the direction as shown and push the RDX drive from the rear until it is projected from the front of the chassis. Then, hold the RDX drive from the front and completely slide it out of the chassis. 1 Figure 59. Removing the RDX drive 5. Touch the static-protective package that contains the new RDX drive to any unpainted surface on the outside of the server.
6. Slide the new RDX drive into the optical drive bay from the front until it snaps into position. Note: You do not need to remove the front bezel when replacing an RDX drive. However, if you are installing an RDX drive, you need to remove the front bezel first, and then gain access to the protective shields to remove them. The following illustration shows only the situation in which the front bezel has been removed. Figure 60. Installing the RDX drive 7.
11. Do one of the following: • If you are installing an RDX drive, save the removed EMI-protective shield from the chassis and plastic shield from the front bezel in the event that you later remove the drive and need the shields to cover the drive bay. • If you are replacing an RDX drive and are instructed to return the old RDX drive, follow all packaging instructions and use any packaging materials that are supplied to you for shipping.
• Use any documentation that comes with the solid-state drive and follow those instructions in addition to the instructions in this topic. Installing a 2.5-inch solid-state drive into a 3.5-inch hard-disk-drive bay Attention: Do not open your server or attempt any repair before reading and understanding “Safety information” on page iii and “Guidelines” on page 65. This topic provides instructions on how to install a 2.5-inch solid-state drive into a 3.5-inch hard-disk-drive bay.
3. Press the release button 1 to open the handle of the dummy hard-disk-drive tray. U CP ME M U PS Figure 63. Opening the handle of the dummy hard-disk-drive tray Chapter 6.
4. Pull the handle and carefully slide the dummy hard-disk-drive tray out of the front of the chassis. 1 U CP ME M U PS Figure 64. Removing the dummy hard-disk-drive tray 5. Touch the static-protective package that contains the 2.5-inch solid-state drive to any unpainted surface on the outside of the server. Then, take the solid-state drive out of the package. Note: Do not touch the circuit board on the solid-state drive.
6. Position the 2.5-inch solid-state drive into the 3.5-inch to 2.5-inch drive adapter as shown in the following illustration. Figure 65. Positioning the 2.5-inch solid-state drive into the drive adapter 7. Align the two screw holes in the solid-state drive with the corresponding holes in the drive adapter. Then, install the two screws to secure the solid-state drive to the drive adapter. Figure 66. Installing the screws to secure the solid-state drive to the drive adapter Chapter 6.
8. Position the drive adapter and the solid-state drive into the 3.5-inch drive bracket. Align the screw holes in the drive adapter and the solid-state drive with the corresponding holes in the bracket. Then, install the five screws to secure the drive adapter and the solid-state drive into the bracket. Figure 67. Installing the screws to secure the drive adapter and the solid-state drive to the bracket 9.
hard-disk-drive status LEDs” on page 28. If the solid-state drive is faulty, reinstall or replace it until it is operating correctly. 11. Save the removed dummy hard-disk-drive tray in the event that you later remove the solid-state drive and need a dummy tray to cover the drive bay. What to do next: • To work with another piece of hardware, go to the appropriate section. • To configure RAID, go to “Configuring RAID” on page 57.
1. Use the front door key to unlock the front door, and then use the front door handle 1 to pivot the front door to the open position. 1 Figure 69. Opening the front door of the server 2. Locate the appropriate hard-disk-drive bay. See “Server components” on page 23.
3. Press the release button 1 to open the handle of the 3.5-inch drive bracket. U CP ME M U PS Figure 70. Opening the handle of the 3.5-inch drive bracket Chapter 6.
4. Pull the handle and carefully slide the bracket with the solid-state drive out of the front of the chassis. 1 U CP ME M U PS Figure 71. Removing the bracket with the solid-state drive 5. Remove the five screws that secure the solid-state drive and the drive adapter. Then, remove the solid-state drive and the drive adapter from the bracket. Figure 72.
6. Remove the two screws that secure the solid-state drive. Figure 73. Removing the screws that secure the solid-state drive 7. Lift the solid-state drive up to remove it from the drive adapter. Figure 74. Removing the solid-state drive from the drive adapter 8. Install a new solid-state drive. See “Installing a 2.5-inch solid-state drive into a 3.5-inch hard-disk-drive bay” on page 108. 9.
This topic provides instructions on how to install or replace a hot-swap hard disk drive. This topic applies only to server models that have hot-swap hard disk drives installed. See “Features” on page 7 for more information about the supported hot-swap hard disk drives. For a list of ThinkServer hard-disk-drive options, go to: http://www.lenovo.
1. Use the front door key to unlock the front door, and then use the front door handle 1 to pivot the front door to the open position. 1 Figure 75. Opening the front door of the server 2. Locate the hard-disk-drive bay. See “Server components” on page 23. Chapter 6.
3. Press the release button 1 to open the handle of the hot-swap hard disk drive or the dummy tray. U CP ME M U PS Figure 76.
4. Pull the handle and carefully slide the hot-swap hard disk drive or the dummy tray out of the front of the chassis. 1 U CP ME M U PS Figure 77. Removing the hot-swap hard disk drive or the dummy tray 5. Touch the static-protective package that contains the new hot-swap hard disk drive to any unpainted surface on the outside of the server. Then, take the new hot-swap hard disk drive out of the package. Note: Do not touch the circuit board on the hard disk drive. Chapter 6.
6. Slide the new hot-swap hard disk drive into the drive bay from the front until it snaps into position, and then completely close the handle. 1 U CP ME M U PS Figure 78. Installing the hot-swap hard disk drive 7. Check the hot-swap hard-disk-drive status LEDs to ensure that the hard disk drive is operating correctly. You might have to restart the server for the newly installed hard disk drive to be recognized. See “Hot-swap hard-disk-drive status LEDs” on page 28.
The hot-swap redundant power supply adds a second source of power to the server. When the server is populated with two hot-swap redundant power supplies, it can withstand a power loss from either power supply. This helps you avoid significant interruption to the operation of the server when a power supply fails. You can replace the failing hot-swap redundant power supply without turning off the server. Some server models come with only one power supply.
1. Do one of the following: • If you are installing a hot-swap redundant power supply, locate the bay for the power supply in the rear of your server. Press the small tab on the metal shield in the direction as shown and pull the tab at the same time to remove the shield out of the chassis. Store the shield in case you later remove the power supply and need the shield to cover the bay. Figure 79.
2. If you are replacing a hot-swap redundant power supply, press the release tab 1 in the direction as shown and carefully pull the handle 2 at the same time to slide the failing hot-swap redundant power supply out of the chassis. Note: Do not use too much strength. You can first carefully slide the redundant power supply a little bit out to release it from the secured position. Then, completely slide it out of the chassis. Figure 80. Removing a hot-swap redundant power supply 3.
4. Note the orientation of the hot-swap redundant power supply, and then slide it into the chassis until it snaps into position. Figure 81. Installing a hot-swap redundant power supply 5. Connect the power cord to the power cord connector on the new hot-swap redundant power supply. Then, check the status LED near the power cord connector. When the LED is lit in green, it indicates that the hot-swap redundant power supply is working correctly.
CAUTION: Never remove the cover on a power supply or any part that has the following label attached. Hazardous voltage, current, and energy levels are present inside any component that has this label attached. There are no serviceable parts inside these components. If you suspect a problem with one of these parts, contact a service technician. Before you begin, print all the related instructions or ensure that you can view the PDF version on another computer for reference.
8. Remove the four screws 1 at the rear of the chassis and the two screws 2 on the metal clip at the front of the power distribution board and cage assembly. Then, push the power distribution board and cage assembly from the rear until it is released from the metal retaining tab 3 . Then, carefully lift the power distribution board and cage assembly out of the chassis. 1 Figure 82. Removing the power distribution board and cage assembly 9.
10. Install the new power distribution board and cage assembly into the chassis. Ensure that the four screw holes 1 in the rear of the new power distribution board and cage assembly are aligned with the corresponding holes marked with R in the rear of the chassis. Meanwhile, ensure that the two screw holes 2 in the metal clip at the front of the new power distribution board and cage assembly are aligned with the corresponding holes in the chassis.
Replacing the power conversion board Attention: Do not open your server or attempt any repair before reading and understanding “Safety information” on page iii and “Guidelines” on page 65. This topic provides instructions on how to replace the power conversion board. This topic applies only to server models that come with a RAID card installed. Before you begin, print all the related instructions or ensure that you can view the PDF version on another computer for reference.
5. Remove the screw that secures the power conversion board. Then, slide the power conversion board to the front of the chassis until it is released from the retention posts on the chassis, and then carefully remove the board out of the chassis. Figure 84. Removing the power conversion board 6. Touch the static-protective package that contains the new power conversion board to any unpainted surface on the outside of the server. Then, remove the new power conversion board from the package.
7. Position the new power conversion board into the chassis so that the three retention posts 1 on the chassis pass through the corresponding holes in the power conversion board. Then, slide the new power conversion board to the rear of the chassis until the power conversion board is securely seated. Ensure that the screw hole in the new power conversion board is aligned with the mounting stud 2 on the chassis. Then, install the screw to secure the new power conversion board in place.
Before you begin, print all the related instructions or ensure that you can view the PDF version on another computer for reference. Notes: • The hot-swap hard-disk-drive backplane is sensitive to ESD. Ensure that you read and understand “Handling static-sensitive devices” on page 66 first and carefully perform the operation. • Depending on the model, your server might look slightly different from the illustrations in this topic. To replace the hot-swap hard-disk-drive backplane, do the following: 1.
9. Do one of the following: • For the backplane for server models with 3.5-inch hard-disk-drive bays, remove the four screws that secure the backplane, and then remove the backplane from the hard-disk-drive cage. Figure 87. Removing the backplane for server models with 3.5-inch hard-disk-drive bays • For the backplane for server models with 2.5-inch hard-disk-drive bays, remove the six screws or three screws that secure the backplane depending on the type of the backplane.
• For the 3.5-inch hot-swap hard-disk-drive cage, install the four screws to secure the backplane on the cage. Figure 89. Installing the backplane for server models with 3.5-inch hard-disk-drive bays • For the 2.5-inch hot-swap hard-disk-drive cage, install the six screws to secure the backplane on the cage. Figure 90. Installing the backplane for server models with 2.5-inch hard-disk-drive bays Note: If you want to install the following backplane for server models with 2.
12. Slide the hard-disk-drive cage into the chassis from the front until it snaps into position. Note: The following illustration shows the 3.5-inch hard-disk-drive cage. For the 2.5-inch hard-disk-drive cage, the installation procedure is the same. Figure 92. Installing the hard-disk-drive cage 13. Reinstall all the hot-swap hard disk drives and dummy trays (if any) in the hard-disk-drive cage. See “Installing or replacing a hot-swap hard disk drive” on page 117. 14.
CAUTION: Hazardous moving parts. Keep fingers and other body parts away. CAUTION: Never remove the cover on a power supply or any part that has the following label attached. Hazardous voltage, current, and energy levels are present inside any component that has this label attached. There are no serviceable parts inside these components. If you suspect a problem with one of these parts, contact a service technician.
7. Remove the four screws 1 at the rear of the chassis that secure the power supply assembly, and then push the power supply assembly from the rear until it is released from the metal retaining tab 2 . Then, carefully lift it out of the chassis. Figure 93. Removing the non-hot-swap power supply assembly 8. Touch the static-protective package that contains the new power supply assembly to any unpainted surface on the outside of the server.
9. Install the new power supply assembly into the chassis so that the four screw holes in the new power supply assembly are aligned with the corresponding holes marked with A in the rear of the chassis. Then, install the four screws 1 to secure the new power supply assembly in place. Note: Use only screws provided by Lenovo. Figure 94. Installing the non-hot-swap power supply assembly 10.
This section provides instructions on how to replace the cover presence switch (intrusion switch). This topic applies only to server models that have the cover presence switch installed. Note: Depending on the model, your server might look slightly different from the illustrations in this topic. To replace the cover presence switch, do the following: 1. Remove all media from the drives and turn off all attached devices and the server.
6. Press the two tabs on the cover presence switch toward each other and carefully push the cover presence switch upward at the same time to remove it out of the frame. Figure 96. Removing the cover presence switch 7. Touch the static-protective package that contains the new cover presence switch to any unpainted surface on the outside of the server. Then, remove the new cover presence switch from the package. 8. Insert the new cover presence switch with the cable into the cover presence switch frame.
9. Insert the tab 1 on the cover presence switch frame into the corresponding hole in the chassis until the frame is securely seated. Ensure that the screw hole in the cover presence switch frame is aligned with the corresponding screw hole in the chassis. Then install the screw to secure the cover presence switch assembly to the chassis. Figure 98. Installing the cover presence switch assembly 10. Connect the cable of the new cover presence switch to the system board.
• The front panel board assembly is sensitive to ESD. Ensure that you read and understand “Handling static-sensitive devices” on page 66 first and carefully perform the operation. To replace the front panel board assembly, do the following: 1. Remove all media from the drives and turn off all attached devices and the server. Then, disconnect all power cords from electrical outlets and disconnect all cables that are connected to the server. 2. Remove the server cover.
11. Route the signal cables of the new front panel board assembly through the corresponding hole in the chassis and position the new front panel board assembly on the chassis so that the screw hole in it is aligned with the corresponding screw hole 1 in the chassis. Then, install the screw to secure the front panel board assembly in place. Figure 100. Installing the front panel board assembly 12. Connect the front panel USB cable to the front USB 3.0 connector on the system board.
CAUTION: Hazardous moving parts. Keep fingers and other body parts away. Before you begin, print all the related instructions or ensure that you can view the PDF version on another computer for reference. Note: Depending on the model, your server might look slightly different from the illustrations in this topic. To replace the front system fan 1, do the following: 1. Remove all media from the drives and turn off all attached devices and the server.
7. Position the new front system fan 1 on the system fan 1 mounting area of the chassis so that the three tips 1 on the bottom of the front system fan 1 are aligned with the corresponding holes in the mounting area. Meanwhile, ensure that the two posts 2 of the front system fan 1 are aligned with the corresponding holes in the inner side of the chassis. Then, carefully slide the front system fan 1 into the chassis until it snaps into position. Figure 102. Installing the front system fan 1 8.
CAUTION: Hazardous moving parts. Keep fingers and other body parts away. Before you begin, print all the related instructions or ensure that you can view the PDF version on another computer for reference. Note: Depending on the model, your server might look slightly different from the illustrations in this topic. To replace the rear system fan, do the following: 1. Remove all media from the drives and turn off all attached devices and the server.
6. Touch the static-protective package that contains the new rear system fan to any unpainted surface on the outside of the server. Then, remove the new rear system fan from the package. 7. Position the new rear system fan, which has four new rubber mounts attached, on the chassis so that the four new rubber mounts are aligned with the corresponding holes in the chassis.
CAUTION: Hazardous moving parts. Keep fingers and other body parts away. CAUTION: The heat sink and fan assembly might be very hot. Turn off the server and wait three to five minutes to let the server cool before removing the server cover. Before you begin, print all the related instructions or ensure that you can view the PDF version on another computer for reference. Note: Depending on the model, your server might look slightly different from the illustrations in this topic.
6. Remove the four screws that secure the heat sink and fan assembly to the system board. It is recommended that you carefully remove the four screws from the system board using the following method to avoid any possible damage to the system board. a. Partially remove screw 1 , then completely remove screw 2 , and then return to screw 1 and completely remove it. b. Partially remove screw 3 , then completely remove screw 4 , and then return to screw 3 and completely remove it.
10. Install the four screws to secure the new heat sink and fan assembly and the backplane on the system board. It is recommended that you carefully install the four screws using the following method to avoid any possible damage to the system board. a. Partially tighten screw 1 , then firmly tighten screw 2 , and then return to screw 1 and firmly tighten it. Do not over-tighten the screws. b. Partially tighten screw 3 , then firmly tighten screw 4 , and then return to screw 3 and firmly tighten it.
CAUTION: The heat sink and fan assembly and the microprocessor might be very hot. Turn off the server and wait three to five minutes to let the server cool before removing the server cover. Before you begin, print all the related instructions or ensure that you can view the PDF version on another computer for reference. Notes: • Ensure that the new microprocessor is the correct type your server supports. See “Memory module installation rules” on page 74.
5. Gently press down the small handle on the microprocessor socket, and then pull the handle a little bit outward to release it from the secured position. Then, pivot the handle upward until the handle and the microprocessor retainer are in the fully open position. Figure 107. Lifting the handle to open the microprocessor retainer Chapter 6.
6. Touch only the edges of the microprocessor and carefully lift it straight up and out of the microprocessor socket. Place the old microprocessor on a static-protective surface. Notes: • Do not touch the gold contacts on the bottom of the microprocessor. • Do not drop anything onto the microprocessor socket while it is exposed. The socket pins must be kept as clean as possible. Figure 108. Removing the microprocessor 7.
9. Note the orientation of the new microprocessor. Hold the new microprocessor by its edges and align the notches 1 on it with the tabs 2 in the microprocessor socket. Then, carefully lower the new microprocessor straight down into the microprocessor socket. Note: The small triangle 3 on one corner of the new microprocessor is the microprocessor orientation indicator. The new microprocessor is in the correct orientation when this indicator faces the beveled corner 4 of the microprocessor socket.
Replacing the system board battery Attention: Do not open your server or attempt any repair before reading and understanding “Safety information” on page iii and “Guidelines” on page 65. This topic provides instructions on how to replace the system board battery. Your server has a special type of memory that maintains the date, time, and configuration information for built-in features. The system board battery keeps the information active when you turn off the server.
6. Remove the old system board battery. Figure 112. Removing the system board battery 7. Install a new system board battery. Figure 113. Installing the system board battery 8. Reinstall the PCI Express card (such as the RAID card) that has been removed. See “Installing the RAID card” on page 83. 9. Dispose of the old system board battery as required by local ordinances or regulations. What to do next: • To work with another piece of hardware, go to the appropriate section.
CAUTION: The heat sink and microprocessor might be very hot. Turn off the server and wait three to five minutes to let the server cool before removing the server cover. Before you begin, print all the related instructions or ensure that you can view the PDF version on another computer for reference. Note: Depending on the model, your server might look slightly different from the illustrations in this topic. To replace the system board, do the following: 1.
8. Remove the eight screws that secure the system board following the recommended numerical sequence as shown. Then, carefully remove the system board out of the chassis. Figure 114. Removing the screws that secure the system board 9. Place the old system board on a clean, flat, and static-protective surface. Touch the static-protective package that contains the new system board to any unpainted surface on the outside of the server. Then, remove the new system board from the package. Chapter 6.
10. Note the orientation of the new system board and carefully place it into the chassis. Ensure that the rear connectors on the new system board are inserted into the corresponding holes in the rear panel and the eight screw holes in the new system board are aligned with the corresponding mounting studs on the chassis. Then, install the eight screws following the recommended numerical sequence as shown to secure the new system board in place. Figure 115.
11. For the new system board, gently press down the small handle on the microprocessor socket and then pull the handle slightly outward to release it from the secured position. Then, pivot the handle upward until the handle and the microprocessor retainer are in the fully open position. Remove the microprocessor socket cover from the microprocessor socket. Note: Do not drop anything onto the microprocessor socket while it is exposed. The socket pins must be kept as clean as possible. Figure 116.
To install a microprocessor socket cover on the old system board, do the following: a. Ensure that the small handle and the microprocessor retainer are in the fully open position. Hold the microprocessor socket cover and align the small triangle 3 on the socket cover with the beveled corner 4 on the microprocessor socket. You also can align the notches 1 on the socket cover with the tabs 2 in the microprocessor socket.
• To complete the replacement, go to “Completing the parts replacement” on page 163. • After a system board is replaced, do the following: 1. Start the Setup Utility program by pressing the F1 key, and then check the BIOS and BMC version. 2. Go to http://www.lenovo.com/drivers and follow the instructions on the Web page to download the latest version of firmware. Then, install the firmware to your server. 3. Update the machine type, model number, and serial number of the system board.
Figure 119. Cable routing 3. If you have removed the front bezel, reinstall it. See “Removing and reinstalling the front bezel” on page 69. 4. Position the server cover on the chassis so that the rail on the bottom of the server cover engages the bottom rail on the chassis. Then, align the four tabs 1 on the server cover with the corresponding holes in the top edge of the chassis. Pivot the server cover to close it. Figure 120.
5. Slide the server cover to the front of the chassis until it snaps into position. Figure 121. Installing the server cover 6. Tighten the thumbscrew on the server cover to secure the server cover in place. Note: For safety consideration, ensure that you use a tool, for example a screwdriver, to tighten the thumbscrew and always ensure that the thumbscrew is securely installed. Also, do not over-tighten the thumbscrew. 7. Lock the server cover and server front door to ensure the security.
• To update the BIOS configuration, see “Using the Setup Utility program” on page 47. • To update the RAID configuration, see “Configuring RAID” on page 57. • To use the ThinkServer EasyStartup program, see “Using the ThinkServer EasyStartup program” on page 54. • To update your system firmware, see “Updating the firmware” on page 62.
Chapter 7. Troubleshooting and diagnostics This chapter provides information about basic troubleshooting and diagnostic methods to help you solve problems that might occur in the server. If you cannot diagnose and correct a problem by using the information in this chapter, see Chapter 8 “Getting information, help, and service” on page 173 for additional troubleshooting resources.
• ThinkServer Diagnostic Tool • ThinkServer System Profile Collection Tool To use a diagnostic program, do the following: 1. Go to http://www.lenovo.com/drivers and follow the instructions on the Web page to locate a diagnostic program. 2. Download and unzip the diagnostic program package to get the diagnostic program package folder. 3. Open the diagnostic program package folder and run the QTW.exe file. 4. Select the language when prompted. Then, click Continue. 5.
Optical drive problems Follow the suggested actions for the corresponding symptom in the order in which they are listed until the problem is solved. If none of these actions solve the problem, see “Troubleshooting procedure” on page 167 for the subsequent steps you should check after using the information in this topic. If the problem cannot be solved by yourself, seek technical assistance. See Chapter 8 “Getting information, help, and service” on page 173. Notes: 1.
Hard-disk-drive problems Follow the suggested actions for the corresponding symptom in the order in which they are listed until the problem is solved. If none of these actions solve the problem, see “Troubleshooting procedure” on page 167 for the subsequent steps you should check after using the information in this topic. If the problem cannot be solved by yourself, seek technical assistance. See Chapter 8 “Getting information, help, and service” on page 173. Notes: 1.
Action Symptom 9. If you suspect a problem with the backplane signal cable or the backplane: a. Replace the affected backplane signal cable. b. Replace the affected backplane. Multiple hard disk drives fail. 1. If you have any diagnostic programs, run the diagnostic programs to test the hard disk drives. 2. Ensure that the cable connection is correct. See “Connecting the cables” on page 36. 3. Reconnect the power cable. 4. Reconnect the signal cable. 5. Replace the affected signal cable. 6.
Keyboard, mouse, or USB device problems Follow the suggested actions for the corresponding symptom in the order in which they are listed until the problem is solved. If none of these actions solve the problem, see “Troubleshooting procedure” on page 167 for the subsequent steps you should check after using the information in this topic. Action Symptom All or some keys on the keyboard do not work. 1. Ensure that: • The USB keyboard cable is securely connected to a USB connector on the server.
Chapter 8. Getting information, help, and service This chapter contains information about help, service, and technical assistance for products manufactured by Lenovo and where to go for additional information about Lenovo and Lenovo products. Information resources You can use the information in this topic to access useful resources relating to your needs when using the product.
• Diagnostic solutions • Product and service warranty • Product and parts details • User guides and manuals • Knowledge base and frequently asked questions Help and service This topic contains information about obtaining help and service. Before you call Before you call, do the following to try to solve the problem by yourself: • Check all cables to ensure that they are connected. • Check the power buttons to ensure that the system and optional devices are turned on.
The warranty does not cover the following: • Replacement or use of parts not manufactured for or by Lenovo or non-warranted Lenovo parts • Identification of software problem sources • Configuration of the UEFI BIOS as part of an installation or upgrade • Changes, modifications, or upgrades to device drivers • Installation and maintenance of network operating systems (NOS) • Installation and maintenance of application programs For the warranty type and duration for your product, refer to the Warranty and Sup
176 ThinkServer TS440 Hardware Maintenance Manual
Appendix A. Notices Lenovo may not offer the products, services, or features discussed in this document in all countries. Consult your local Lenovo representative for information on the products and services currently available in your area. Any reference to a Lenovo product, program, or service is not intended to state or imply that only that Lenovo product, program, or service may be used.
Trademarks Lenovo, the Lenovo logo, and ThinkServer are trademarks of Lenovo in the United States, other countries, or both. Intel, Intel Core, and Intel Xeon are trademarks of Intel Corporation in the United States, other countries, or both. Linux is a registered trademark of Linus Torvalds. Microsoft and Windows are trademarks of the Microsoft group of companies. Other company, product, or service names may be trademarks or service marks of others.
Recycling and disposal information for Japan is available at: http://www.lenovo.com/recycling/japan Battery return program This product may contain a lithium or lithium ion battery. Consult your user manual or service manual for specific battery information. The battery must be recycled or disposed of properly. Recycling facilities may not be available in your area. For information on disposal or batteries outside the United States, go to http://www.lenovo.
Products containing manganese dioxide lithium coin cell batteries may contain perchlorate. Perchlorate Material - special handling may apply, See www.dtsc.ca.gov/hazardouswaste/perchlorate Particulate contamination Attention: Airborne particulates (including metal flakes or particles) and reactive gases acting alone or in combination with other environmental factors such as humidity or temperature might pose a risk to the server that is described in this document.
labeled in accordance with local regulations concerning waste electrical and electronic equipment (WEEE). These regulations determine the framework for the return and recycling of used appliances as applicable within each geography. This label is applied to various products to indicate that the product is not to be thrown away, but rather put in the established collection systems for reclaiming these end of life products.
Restriction of Hazardous Substances Directive (RoHS) This topic provides statements about the Restriction of Hazardous Substances Directive (RoHS). European Union RoHS Lenovo products sold in the European Union, on or after 3 January 2013 meet the requirements of Directive 2011/65/EU on the restriction of the use of certain hazardous substances in electrical and electronic equipment (“RoHS recast” or “RoHS 2”). For more information about Lenovo progress on RoHS, go to: http://www.lenovo.
Properly shielded and grounded cables and connectors must be used in order to meet FCC emission limits. Lenovo is not responsible for any radio or television interference caused by using other than specified or recommended cables and connectors or by unauthorized changes or modifications to this equipment. Unauthorized changes or modifications could void the user's authority to operate the equipment. This device complies with Part 15 of the FCC Rules.
ohne Zustimmung der Lenovo verändert bzw. wenn Erweiterungskomponenten von Fremdherstellern ohne Empfehlung der Lenovo gesteckt/eingebaut werden. Deutschland: Einhaltung des Gesetzes über die elektromagnetische Verträglichkeit von Betriebsmittein Dieses Produkt entspricht dem „Gesetz über die elektromagnetische Verträglichkeit von Betriebsmitteln“ EMVG (früher „Gesetz über die elektromagnetische Verträglichkeit von Geräten“).
Index 2.5-inch hot-swap hard-disk-drive backplane locations 35 3.
LED 17 hardware installing 65 removing 65 replacing 65 heat sink and fan assembly replacing 148 help, getting 173 hot-swap hard disk drive installing 117 replacing 117 hot-swap hard-disk-drive backplane locations 32 replacing 132 hot-swap hard-disk-drive status LED 28 hot-swap hard-disk-drive status LEDs locations 28 hot-swap redundant power supply replacing 122 hot-swap redundant power supply status LED 19 hard-disk-drive status 17 hot-swap hard-disk-drive status 28 hot-swap redundant power supply status
power conversion board replacing 130 power distribution board and cage assembly replacing 126 Power menu Setup Utility program 49 power status LED 16 power supply features 8 precautions guidelines 65 R RAID configuring 57 for your server 58 introduction 57 RAID card installing 83 locations 30 removing 83 RAID configuration utilities software 12 rear system fan replacing 146 rear view of the server locations 17 reinstalling front bezel 69 PCI card bracket assembly 71 reliability, availability, and serviceab
system board battery replacing 156 system board components locations 39 system date setting 51 system reliability guidelines 66 system time setting 51 V viewing information Setup Utility program 47 W T the BIOS flashing 53 updating 53 updating or recovering 53 ThinkServer EasyStartup software 11 ThinkServer EasyStartup program features 54 starting 55 using 54 Windows operating system 56 ThinkServer EasyUpdate Firmware Updater software 11 ThinkServer Web address 1 TPM Setup Utility program 52 TR 500 key
