® ThinkPad X200 Tablet Hardware Maintenance Manual
® ThinkPad X200 Tablet Hardware Maintenance Manual
Note Before using this information and the product it supports, be sure to read the general information under “Notices” on page 171. Second Edition (November 2008) © Copyright Lenovo 2008. All rights reserved. LENOVO products, data, computer software, and services have been developed exclusively at private expense and are sold to governmental entities as commercial items as defined by 48 C.F.R. 2.101 with limited and restricted rights to use, reproduction and disclosure.
Contents About this manual . . . . . . . . . . v Safety information . . . . . . . . . . 1 General safety . . . . . . . . . . . . . . 2 Electrical safety . . . . . . . . . . . . . 3 Safety inspection guide . . . . . . . . . . . 5 Handling devices that are sensitive to electrostatic discharge . . . . . . . . . . . . . . . 6 Grounding requirements . . . . . . . . . . 6 Safety notices: multilingual translations . . . . . 7 Laser compliance statement . . . . . . . . . 14 Important service information . . . . .
Parts list . . . Overall . . LCD FRUs . Keyboard . . Miscellaneous AC adapters . Power cords . iv . . . . . . . . parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 139 140 154 161 162 163 164 ThinkPad X200 Tablet Hardware Maintenance Manual Recovery discs . . . Common service tools . . . . . . . . . . . . . . . . . 165 . 170 Notices . . . . . . . . . . . . . . 171 Trademarks . .
About this manual This manual contains service and reference information for the following ThinkPad® products. ThinkPad X200 Tablet MT 4184, 7448, 7449, 7450, 7453, 2263, and 2266 Use this manual along with the advanced diagnostic tests to troubleshoot problems. The manual is divided into sections as follows: v The common sections provide general information, guidelines, and safety information required in servicing computers.
vi ThinkPad X200 Tablet Hardware Maintenance Manual
Safety information This chapter presents following safety information that you need to be familiar with before you service a ThinkPad computer.
General safety Follow these rules to ensure general safety: v Observe good housekeeping in the area of the machines during and after maintenance. v When lifting any heavy object: 1. Make sure that you can stand safely without slipping. 2. Distribute the weight of the object equally between your feet. 3. Use a slow lifting force. Never move suddenly or twist when you attempt to lift. 4. Lift by standing or by pushing up with your leg muscles; this action removes the strain from the muscles in your back.
Electrical safety Observe the following rules when working on electrical equipment. Important: Use only approved tools and test equipment. Some hand tools have handles covered with a soft material that does not insulate you when working with live electrical currents. Many customers have, near their equipment, rubber floor mats that contain small conductive fibers to decrease electrostatic discharges. Do not use this type of mat to protect yourself from electrical shock.
v Do not touch live electrical circuits with the reflective surface of a plastic dental mirror. The surface is conductive; such touching can cause personal injury and machine damage. v Do not service the following parts with the power on when they are removed from their normal operating places in a machine: – Power supply units – Pumps – Blowers and fans – Motor generators and similar units. (This practice ensures correct grounding of the units.
Safety inspection guide The purpose of this inspection guide is to assist you in identifying potentially unsafe conditions. As each machine was designed and built, required safety items were installed to protect users and service personnel from injury. This guide addresses only those items. You should use good judgment to identify potential safety hazards due to attachment of non-ThinkPad features or options not covered by this inspection guide.
Handling devices that are sensitive to electrostatic discharge Any computer part containing transistors or integrated circuits (ICs) should be considered sensitive to electrostatic discharge (ESD.) ESD damage can occur when there is a difference in charge between objects. Protect against ESD damage by equalizing the charge so that the machine, the part, the work mat, and the person handling the part are all at the same charge. Notes: 1.
Safety notices: multilingual translations The safety notices in this section are provided in English, French, German, Hebrew, Italian, Japanese, and Spanish. Safety notice 1 Before the computer is powered on after FRU replacement, make sure all screws, springs, and other small parts are in place and are not left loose inside the computer. Verify this by shaking the computer and listening for rattling sounds. Metallic parts or metal flakes can cause electrical shorts.
Safety notice 2 DANGER Some standby batteries contain a small amount of nickel and cadmium. Do not disassemble a standby battery, recharge it, throw it into fire or water, or short-circuit it. Dispose of the battery as required by local ordinances or regulations. Use only the battery in the appropriate parts listing. Use of an incorrect battery can result in ignition or explosion of the battery. Certaines batteries de secours contiennent du nickel et du cadmium.
Safety notice 3 DANGER The battery pack contains small amounts of nickel. Do not disassemble it, throw it into fire or water, or short-circuit it. Dispose of the battery pack as required by local ordinances or regulations. Use only the battery in the appropriate parts listing when replacing the battery pack. Use of an incorrect battery can result in ignition or explosion of the battery. La batterie contient du nickel. Ne la démontez pas, ne l’exposez ni au feu ni à l’eau. Ne la mettez pas en court-circuit.
Safety notice 4 DANGER The lithium battery can cause a fire, an explosion, or a severe burn. Do not recharge it, remove its polarized connector, disassemble it, heat it above 100°C (212°F), incinerate it, or expose its cell contents to water. Dispose of the battery as required by local ordinances or regulations. Use only the battery in the appropriate parts listing. Use of an incorrect battery can result in ignition or explosion of the battery. La pile de sauvegarde contient du lithium.
Safety notice 5 If the LCD breaks and the fluid from inside the LCD gets into your eyes or on your hands, immediately wash the affected areas with water for at least 15 minutes. Seek medical care if any symptoms from the fluid are present after washing. Si le panneau d’affichage à cristaux liquides se brise et que vous recevez dans les yeux ou sur les mains une partie du fluide, rincez-les abondamment pendant au moins quinze minutes. Consultez un médecin si des symptômes persistent après le lavage.
Safety notice 6 DANGER To avoid shock, do not remove the plastic cover that protects the lower part of the inverter card. Afin d’éviter tout risque de choc électrique, ne retirez pas le cache en plastique protégeant la partie inférieure de la carte d’alimentation. Aus Sicherheitsgründen die Kunststoffabdeckung, die den unteren Teil der Spannungswandlerplatine umgibt, nicht entfernen.
Safety notice 8 DANGER Before removing any FRU, power off the computer, unplug all power cords from electrical outlets, remove the battery pack, and then disconnect any interconnecting cables. Avant de retirer une unité remplaçable en clientèle, mettez le système hors tension, débranchez tous les cordons d’alimentation des socles de prise de courant, retirez la batterie et déconnectez tous les cordons d’interface.
Laser compliance statement Some models of ThinkPad computer are equipped from the factory with an optical storage device such as a CD-ROM drive or a DVD-ROM drive. Such devices are also sold separately as options. If one of these drives is installed, it is certified in the U.S. to conform to the requirements of the Department of Health and Human Services 21 Code of Federal Regulations (DHHS 21 CFR) Subchapter J for Class 1 laser products.
A CD-ROM drive, a DVD-ROM drive, or any other storage device installed may contain an embedded Class 3A or Class 3B laser diode. Note the following: DANGER Emits visible and invisible laser radiation when open. Do not stare into the beam, do not view directly with optical instruments, and avoid direct exposure to the beam. Radiação por raio laser ao abrir. Não olhe fixo no feixe de luz, não olhe diretamente por meio de instrumentos óticos e evite exposição direta com o feixe de luz.
16 ThinkPad X200 Tablet Hardware Maintenance Manual
Important service information This chapter presents following important service information: v “Strategy for replacing FRUs” – “Strategy for replacing a hard disk drive” on page 18 – “Important notice for replacing a system board” on page 18 – “How to use error message” on page 18 v “Strategy for replacing FRUs for CTO, CMV, and GAV” on page 19 – “Product definition” on page 19 – “FRU identification for CTO, CMV, and GAV products” on page 19 v “Important information about replacing RoHS compliant FRUs” on p
v If you are instructed to replace a FRU but the replacement does not correct the problem, reinstall the original FRU before you continue. v Some computers have both a processor board and a system board. If you are instructed to replace either the processor board or the system board, and replacing one of them does not correct the problem, reinstall that board, and then replace the other one. v If an adapter or a device consists of more than one FRU, any of the FRUs may be the cause of the error.
Strategy for replacing FRUs for CTO, CMV, and GAV Product definition Dynamic Configure To Order (CTO) This provides the ability for a customer to configure an IBM® or a Lenovo solution from an eSite, and have this configuration sent to fulfillment, where it is built and shipped directly to the customer. The machine label, Product Entitlement Warehouse (PEW), eSupport, and the HMM will load these products as the 4-digit MT and 3-digit model, where model = “CTO” (Example: 1829-CTO).
warranty.vm&sitestyle=lenovo Select Warranty lookup. Input the MT and the Serial number and the list of key commodities will be returned in the PEW record under COMPONENT INFORMATION. v Business Partners using Eclaim will access PEW when performing Entitlement Lookup. Business Partners will enter Loc ID, MT and Serial, and the key commodities will be returned in the Eclaim record under SYSTEM DETAILS. v Authorized IBM Business Partners can access Eclaim at the following Web site: https://wca.eclaim.
Important information about replacing RoHS compliant FRUs RoHS, The Restriction of Hazardous Substances in Electrical and Electronic Equipment Directive (2002/95/EC) is a European Union legal requirement affecting the global electronics industry. RoHS requirements must be implemented on Lenovo products placed on the market after June 2006. Products on the market before June 2006 are not required to have RoHS compliant parts.
22 ThinkPad X200 Tablet Hardware Maintenance Manual
General checkout This chapter presents following information: v “What to do first” on page 24 v “Checkout guide” on page 25 – “Diagnostics using PC-Doctor for DOS” on page 26 – “PC-Doctor for Windows” on page 28 – “PC-Doctor for Rescue and Recovery” on page 28 v “Power system checkout” on page 29 The descriptions in this chapter apply to any ThinkPad model that supports the PC-Doctor® for DOS diagnostics program. Some descriptions might not apply to your particular computer.
What to do first When you do return a FRU, you must include the following information in the parts exchange form or parts return form that you attach to it: __ 1. Name and phone number of servicer __ 2. Date of service __ 3. Date on which the machine failed __ 4. Date of purchase __ 5. Failure symptoms, error codes appearing on the display, and beep symptoms __ 6. Procedure index and page number in which the failing FRU was detected __ 7. Failing FRU name and part number __ 8.
Checkout guide Use the following procedures as a guide in identifying and correcting problems with the ThinkPad computer. Note: The diagnostic tests are intended to test only ThinkPad products. The use of non-ThinkPad products, prototype cards, or modified options can lead to false indications of errors and invalid system responses. 1. Identify the failing symptoms in as much detail as possible. 2. Verify the symptoms.
Diagnostics using PC-Doctor for DOS The ThinkPad computer has a test program called PC-Doctor for DOS (hereafter called PC-Doctor.) You can detect errors by running the diagnostics test included in PC-Doctor. This section is an overview of the procedure. For details that depend on model-unique functions, refer to “ThinkPad X200 Tablet” on page 47. Note: PC-Doctor for DOS is available at following Web site: http://www.lenovo.
Note: PC-Doctor menu does not mean the formal support device list. Some unsupported device names may appear in the PC-Doctor menu. Diagnostics Interactive Tests Hardware Info Utility Quit F1=Help Run Normal Test Run Quick Test CPU/Coprocessor Systemboard Video Adapter Serial Ports Parallel Ports Fixed Disks Diskette Drives Other Devices Communication Wireless LAN PM Memory PC-DOCTOR 2.0 Copyright 2002 PC-Doctor, Inc. All Rights Reserved. Use the cursor keys and ESC to move in menus.
Detecting system information with PC-Doctor PC-Doctor can detect the following system information: Hardware Info v System Configuration v Memory Contents v Physical Disk Drives v Logical Disk Drives v VGA Information v IDE Drive Info v PCI Information v PNPISA Info v SMBIOS Info v VESA LCD Info v Hardware Events Log Utility v v v v v v v v v v v Run External Tests Surface Scan Hard Disk Benchmark System DOS Shell Tech Support Form Battery Rundown View Test Log Print Log Save Log Full Erase Hard Drive Quick
Power system checkout To 1. 2. 3. 4. 5. 6. 7. verify a symptom, do the following: Turn off the computer. Remove the battery pack. Connect the ac adapter. Check that power is supplied when you turn on the computer. Turn off the computer. Disconnect the ac adapter and install the charged battery pack. Check that the battery pack supplies power when you turn on the computer.
Checking operational charging To check whether the battery charges properly during operation, use a discharged battery pack or a battery pack that has less than 50% of the total power remaining when installed in the computer. Perform operational charging. If the battery status indicator or icon does not turn on, remove the battery pack and let it return to room temperature. Reinstall the battery pack. If the charge indicator or icon still does not turn on, replace the battery pack.
Checking the backup battery Do the following: 1. Power off the computer, and unplug the ac adapter from it. 2. Turn the computer upside down. 3. Remove the battery pack (see “1020 Battery pack” on page 63). 4. Remove the backup battery (see “1090 Backup battery” on page 78). 5. Measure the voltage of the backup battery. See the following figure. Red (+) Black (-) Wire Voltage (V dc) Red +2.5 to +3.2 Black Ground v If the voltage is correct, replace the system board.
32 ThinkPad X200 Tablet Hardware Maintenance Manual
Related service information This chapter presents following information: v “Restoring the factory contents by using Product Recovery discs” v “Passwords” on page 34 v “Power management” on page 37 v “Symptom-to-FRU index” on page 39 Service Web site: When the latest maintenance diskette and the system program service diskette become available, they will be posted on http://www.lenovo.
8. When the recovery process is complete, the Welcome to Microsoft Windows screen is displayed. Follow the instructions on the screen to complete the Windows setup. Passwords As many as three passwords may be needed for any ThinkPad computer: the power-on password (POP), the hard-disk password (HDP), and the supervisor password (SVP). If any of these passwords has been set, a prompt for it appears on the screen whenever the computer is turned on. The computer does not start until the password is entered.
How to remove the power-on password To remove a POP that you have forgotten, do the following: (A) If no SVP has been set: 1. Turn off the computer. 2. Remove the battery pack. For how to remove the battery pack, see “1020 Battery pack” on page 63. 3. Remove the backup battery. For how to remove the backup battery, see “1090 Backup battery” on page 78. 4. Turn on the computer and wait until the POST ends. After the POST ends, the password prompt does not appear. The POP has been removed. 5.
3. 4. 5. 6. 7. 8. 9. 36 Note: To check whether the ThinkPad computer supports the Passphrase function, enter the BIOS Setup Utility and go to Security --> Password. If Using Passphrase item is displayed in the menu, this function is available on the ThinkPad computer. Select Security, using the cursor directional keys to move down the menu. Select Password. Select Hard-disk x password, where x is the letter of the hard disk drive. A pop-up window opens. Select Master HDP.
Power management To reduce power consumption, the computer has three power management modes: screen blank, standby, and hibernation. Screen blank mode If the time set on the “Turn off monitor” timer in the operating system expires, the LCD backlight turns off. To put the computer into screen blank mode, press the ThinkVantage® button and use the ThinkVantage Productivity Center. To end screen blank mode and resume normal operation, press any key.
v The ring indicator (RI) is signaled by a serial device or a PC Card device. v The time set on the resume timer elapses. Note: The computer does not accept any input immediately after it enters standby mode. Wait a few seconds before taking any action to reenter operation mode. Hibernation mode In hibernation mode, the following occurs: v The system status, RAM, VRAM, and setup data are stored on the hard disk. v The system is powered off.
Symptom-to-FRU index This section contains following information: v “Numeric error codes” v “Error messages” on page 43 v “Beep symptoms” on page 44 v “No-beep symptoms” on page 44 v “LCD-related symptoms” on page 45 v “Intermittent problems” on page 46 v “Undetermined problems” on page 46 The symptom-to-FRU index in this section lists symptoms and errors and their possible causes. The most likely cause is listed first, in boldface type.
Table 1. Numeric error codes (continued) Symptom or error FRU or action, in sequence 0187 EAIA data access error—The access to EEPROM is failed. System board. 0188 Invalid RFID Serialization Information Area. System board. 0189 System board. Invalid RFID configuration information area—The EEPROM checksum is not correct. 40 0190 Critical low-battery error 1. Charge the battery pack. 2. Battery pack. 0191 System Security—Invalid Remote Change requested. 1.
Table 1. Numeric error codes (continued) Symptom or error FRU or action, in sequence 0250 System battery error—System battery is dead. 1. Charge the backup battery for more than 8 hours by connecting the ac adapter. 2. Replace the backup battery and run BIOS Setup Utility to reset the time and date. 0251 System CMOS checksum bad— Default configuration used. 1. Charge the backup battery for more than 8 hours by connecting the ac adapter. 2.
Table 1. Numeric error codes (continued) Symptom or error FRU or action, in sequence 1804 Unauthorized WAN card is plugged in—Power off and remove the WAN card. 1. Remove the WAN card that you installed. 2. System board. 1805 Unauthorized Wireless USB card is plugged in—Power off and remove the Wireless USB card. 1. Remove the Wireless USB card that you installed. 2. System board. 1820 More than one external fingerprint reader is attached.
Error messages Table 2. Error messages Symptom or error FRU or action, in sequence Device address conflict. 1. Load “Setup Defaults” in the BIOS Setup Utility. 2. Backup battery. 3. System board. Allocation error for device. 1. Load “Setup Defaults” in the BIOS Setup Utility. 2. Backup battery. 3. System board. Failing bits: nnnn. 1. DIMM. 2. System board. Invalid system configuration data. 1. DIMM. 2. System board. I/O device IRQ conflict. 1. Load “Setup Defaults” in the BIOS Setup Utility. 2.
Beep symptoms Table 3. Beep symptoms Symptom or error FRU or action, in sequence One beep and a blank, unreadable, or flashing LCD. 1. 2. 3. 4. One long and two short beeps, and a blank or unreadable LCD. 1. System board. 2. LCD assembly. 3. DIMM. Two short beeps with error codes. POST error. See “Numeric error codes” on page 39. Two short beeps and a blank screen. 1. System board. 2. DIMM. Three short beeps, pause, three more short beeps, and one short beep. 1. DIMM. 2.
LCD-related symptoms Important: The TFT LCD for the notebook computer contains many thin-film transistors (TFTs). The presence of a small number of dots that are missing, discolored, or always lighted is characteristic of TFT LCD technology, but excessive pixel problems can cause viewing concerns. The LCD should be replaced if the number of missing, discolored, or lighted dots in any background is as follows: Table 5.
Intermittent problems Intermittent system hang problems can be due to a variety of causes that have nothing to do with a hardware defect, such as cosmic radiation, electrostatic discharge, or software errors. FRU replacement should be considered only when a problem recurs. When analyzing an intermittent problem, do the following: 1. Run the diagnostic test for the system board in loop mode at least 10 times. 2. If no error is detected, do not replace any FRUs. 3.
ThinkPad X200 Tablet This chapter presents following product-specific service references and product-specific parts information.
Specifications The following table lists the specifications of the ThinkPad X200 Tablet : Table 7. Specifications Feature Description Processor v Intel® Core™ 2 Duo processor SU9300 (1.2 GHz), 800-MHz FSB, 3-MB L2 cache v Intel Core 2 Duo processor SL9300 (1.6 GHz), 1066-MHz FSB, 6-MB L2 cache v Intel Core 2 Duo processor SL9400 (1.86 GHz), 1066-MHz FSB, 6-MB L2 cache Bus architecture v v v v v Graphic memory chip v Intel® Integrated Graphics 4500MHD Display v 12.
Table 7.
Status indicators The system status indicators show the status of the computer, as follows: 1 2 3 4 5 10 6 7 9 8 9 10 8 Table 8. Status indicators 50 Indicator Meaning 1 Green: The wireless LAN feature is on, and the radio link is ready for use. Blinking green: Data is being transmitted.
Table 8. Status indicators (continued) Indicator Meaning 2 Green: Wireless PAN (Bluetooth wireless or Wireless USB) is operational. This indicator is on when Wireless PAN is on and not in suspend mode. Wireless PAN status R or 3 Wireless WAN status Green: The wireless WAN is on, and the radio link is ready for use. Blinking green: Data is being transmitted. 4 Num lock Green: The numeric keypad on the keyboard is enabled.
FRU tests The following table shows the test for each FRU. Table 9. FRU tests FRU Applicable test System board 1. Diagnostics --> CPU/Coprocessor 2. Diagnostics --> Systemboard 3. If the ThinkPad X200 UltraBase is attached to the ThinkPad computer, detach it. Place the computer on a horizontal surface, and run Diagnostics --> ThinkPad Devices --> HDD Active Protection Test. Note: Do not apply any physical shock to the computer while the test is running.
Table 9. FRU tests (continued) FRU Applicable test DVD drive or DVD/CD-RW combo drive 1. Diagnostics --> Other Devices--> Optical Drive 2. Interactive Tests --> Optical Drive Test Memory 1. If two DIMMs are installed, remove one of them and run Diagnostics --> PM Memory. 2. If the problem does not recur, return the DIMM to its place, remove the other one, and run the test again. Fan 1. Turn on the computer and check the air turbulence at the louver near the PC Card slot. 2.
Fn key combinations The following table shows the function of each combination of Fn with a function key. Table 10. Fn key combinations Key combination Description Fn+F1 Reserved. Fn+F2 Lock the computer. Fn+F3 Select a power scheme that has been created by Power Manager. When you press this combination, a panel for selecting a power scheme appears. Notes: 1. To use the Fn+F3 key combination, you must have the ThinkPad PM device driver installed on the computer. 2.
Table 10. Fn key combinations (continued) Key combination Description Fn+F7 Apply a presentation scheme directly, with no need to start Presentation Director. To disable this function and use the Fn+F7 key combination for switching a display output location, start Presentation Director, and change the settings. Switch a display output location v External monitor (CRT display) v Computer display and external monitor (LCD + CRT display) v Computer display (LCD) Notes: 1.
FRU replacement notices This section contains notices related to removing and replacing parts. Read this section carefully before replacing any FRU. Screw notices Loose screws can cause a reliability problem. In the ThinkPad computer, this problem is addressed with special nylon-coated screws that have the following characteristics: v They maintain tight connections. v They do not easily come loose, even with shock or vibration. v They are harder to tighten. v Each one should be used only once.
Retaining serial numbers This section includes the following descriptions: v “Restoring the serial number of the system unit” v “Retaining the UUID” v “Reading or writing the ECA information” on page 59 Restoring the serial number of the system unit When the computer was manufactured, the EEPROM on the system board was loaded with the serial numbers of the system and all major components. These numbers need to remain the same throughout the life of the computer.
When you replace the system board, you must set the UUID on the new system board as follows: 1. Install the ThinkPad Hardware Maintenance Diskette Version 1.73 or later, and restart the computer. 2. From the main menu, select 4. Assign UUID. A new UUID is created and written. If a valid UUID already exists, it is not overwritten.
Reading or writing the ECA information Information on Engineering Change Announcements (ECA) are stored in the EEPROM of the system board. The electronic storage of this information simplifies the procedure to check if the ECA has been previously applied to a machine. The machine does not need to be disassembled to check for the ECA application. To check what ECAs have been previously applied to the machine, use the ECA Information Read/Write function on the ThinkPad Hardware Maintenance Diskette Version 1.
Removing and replacing a FRU This section presents directions and drawings for use in removing and replacing a FRU. Be sure to observe the following general rules: 1. Do not try to service any computer unless you have been trained and certified. An untrained person runs the risk of damaging parts. 2. Before replacing any FRU, review “FRU replacement notices” on page 56. 3. Begin by removing any FRUs that have to be removed before the failing FRU. Any such FRUs are listed at the top of the page.
Before servicing ThinkPad X200 Tablet Removing the SIM card: Some models of the ThinkPad X200 Tablet you are servicing might have the SIM card that the customer has been installed. If the computer you are servicing has the SIM card, remove it before you start the servicing. To remove the SIM card, you need to remove the battery pack first. (See “1020 Battery pack” on page 63.) After you finish the servicing, make sure that you insert the card back into the slot firmly.
1010 Digitizer pen Table 11.
1020 Battery pack DANGER Use only the battery specified in the parts list for your computer. Any other battery could ignite or explode. Table 12. Removal steps of battery pack Unlock the battery release lever. Holding the battery release lever in the unlocked position 1 , remove the battery pack in the direction shown by arrow 2 . 1 2 When installing: Install the battery pack along the slide rails of the slot. Then make sure that the battery release lever is in the locked position.
1030 Hard disk drive (HDD) cover, HDD, and HDD rubber rails or solid state drive (SSD) and storage converter For access, remove this FRU: v “1020 Battery pack” on page 63 Attention: v Do not drop the hard disk drive or apply any physical shock to it. The hard disk drive is sensitive to physical shock. Improper handling can cause damage and permanent loss of data. v Before removing the drive, have the user make a backup copy of all the information on it if possible.
Table 13. Removal steps of HDD cover, HDD, and HDD drive rubber rails or SSD and storage converter (continued) 4 5 When installing: Make sure that the HDD connector or SSD connector is attached firmly.
Table 13. Removal steps of HDD cover, HDD, and HDD drive rubber rails or SSD and storage converter (continued) HDD and HDD rubber rails: 6 6 When installing: The rubber rails on the hard disk drive must be attached to the replacement drive. Otherwise the drive cannot be installed properly.
Table 13. Removal steps of HDD cover, HDD, and HDD drive rubber rails or SSD and storage converter (continued) When installing: When you install the SSD in the storage converter, do as follows.
1040 DIMM For access, remove this FRU in order: v “1020 Battery pack” on page 63 Table 14. Removal steps of dimm Remove the DIMM slot cover as shown in this figure. Note: Loosen the screws 1 , but do not remove them.
Table 14. Removal steps of dimm (continued) Note: If only one DIMM is used on the computer you are servicing, the card must be installed in SLOT-0 ( a ), but not in SLOT-1 ( b ). a b When installing: Insert the notched end of the DIMM into the socket. Press the DIMM firmly, and pivot it until it snaps into the place. Make sure that it is firmly fixed in the slot and does not move easily.
1050 Hinge caps For access, remove this FRU in order: v “1020 Battery pack” on page 63 Table 15. Removal steps of hinge caps 1 Open the LCD unit, and then remove the hinge cap (front).
Table 15. Removal steps of hinge caps (continued) Close the LCD unit, and then remove the hinge cap (rear).
1060 Keyboard For access, remove this FRU in order: v “1020 Battery pack” on page 63 Table 16. Removal steps of keyboard 1 1 1 1 Step 1 72 Icon Screw (quantity) Color Torque M2 × 6 mm, wafer-head, nylon-coated (4) Black 0.181 Nm (1.
Table 16. Removal steps of keyboard (continued) 3 2 3 3 Lift the keyboard a little in the direction shown by arrow 4 , and then detach the connector 5 .
Table 16. Removal steps of keyboard (continued) When installing: 1. Attach the keyboard connector firmly. 2. Make sure that the keyboard edges are under the frame as shown in this figure. Then press the keys to latch the keyboard firmly in place. 3. To make sure that the front side of the keyboard is housed firmly, gently press the keys with your thumbs and try to slide the keyboard toward you. 4. Secure the keyboard by tightening the screws from the bottom side of the computer.
1070 Extension cable card For access, remove these FRUs in order: v “1020 Battery pack” on page 63 v “1060 Keyboard” on page 72 Table 17. Removal steps of backup battery 2 1 2 1 1 1 1 3 3 Step Screw (quantity) Color 1 M2 × 3.5 mm, wafer-head, nylon-coated (5) Black 0.181 Nm (1.85 kgfcm) 2 M2 × 6 mm, flat-head, nylon-coated (2) 0.181 Nm (1.85 kgfcm) Silver Torque When installing: Make sure that the connectors are attached firmly.
1080 Palm rest For access, remove this FRU in order: v “1020 Battery pack” on page 63 v “1060 Keyboard” on page 72 Table 18. Removal steps of palm rest 1 1 1 1 Step Icon 1 1 Screw (quantity) Color Torque M2 × 6 mm, wafer-head, nylon-coated (5) Black 0.181 Nm (1.
Table 18. Removal steps of palm rest (continued) When installing: When you attach the palm rest, do as follows: 1. Press the left and right top edges of the palm rest to fit it into place. 2. Push the front side of the palm rest until it clicks into place. 1 1 2 2 3. Close the LCD cover and turn the computer over. Then fasten the five screws to secure the palm rest.
1090 Backup battery DANGER Use only the battery specified in the parts list for your computer. Any other battery could ignite or explode. For access, remove these FRUs in order: v “1020 Battery pack” on page 63 v “1060 Keyboard” on page 72 v “1080 Palm rest” on page 76 Table 19.
Table 19. Removal steps of backup battery (continued) 3 2 When installing: Make sure that the battery connector is attached firmly.
1100 PCI Express Mini Card for wireless LAN For access, remove these FRUs in order: v “1020 Battery pack” on page 63 v “1060 Keyboard” on page 72 v “1080 Palm rest” on page 76 Table 20. Removal steps of PCI Express Mini Card for wireless LAN Full size PCI Express Mini Card: In step 1 , unplug the jacks by using the removal tool antenna RF connector (P/N: 08K7159) or pick the connectors with your fingers and gently unplug them in direction of the arrow.
Table 20. Removal steps of PCI Express Mini Card for wireless LAN (continued) 3 When installing: v In models with wireless LAN card that has two antenna connectors, plug the gray cable into the jack labeled MAIN on the card, and the black cable into the jack labeled AUX. If the computer you are servicing has three cables, put the white cable in the cable protection tube.
Table 20. Removal steps of PCI Express Mini Card for wireless LAN (continued) Harf size PCI Express Mini Card: In step 1 , unplug the jacks by using the removal tool antenna RF connector (P/N: 08K7159) or pick the connectors with your fingers and gently unplug them in direction of the arrow. 2 2 1 Step Screw (quantity) Color 2 M2 × 3.5 mm, wafer-head, nylon-coated (2) Silver 3 82 ThinkPad X200 Tablet Hardware Maintenance Manual Torque 0.181 Nm (1.
Table 20. Removal steps of PCI Express Mini Card for wireless LAN (continued) When installing: v Plug the gray cable into the jack labeled MAIN on the card, and the black cable into the jack labeled AUX.
1110 PCI Express Mini Card for wireless WAN For access, remove these FRUs in order: v “1020 Battery pack” on page 63 v “1060 Keyboard” on page 72 v “1080 Palm rest” on page 76 Table 21. Removal steps of PCI Express Mini Card for wireless WAN In step 1 , unplug the jacks by using the removal tool antenna RF connector (P/N: 08K7159) or pick the connectors with your fingers and gently unplug them in direction of the arrow. 2 2 1 84 Step Screw (quantity) 3 M2 × 3.
Table 21. Removal steps of PCI Express Mini Card for wireless WAN (continued) 3 When installing: When you install the card, plug the red cable into the jack labeled MAIN on the card, and the blue cable into the jack labeled AUX. If the computer you are servicing is the wireless WAN-ready model, put the antenna cables in the cable protection tube and place them as shown in this figure.
1120 Intel Turbo Memory Minicard or wireless USB adapter For access, remove these FRUs in order: v “1020 Battery pack” on page 63 v “1060 Keyboard” on page 72 v “1080 Palm rest” on page 76 Table 22. Removal steps of Intel Turbo Memory Minicard or wireless USB adapter Note: Step 1 is only for models with the wireless USB adapter. For models with the Intel Turbo Memory Minicard, skip step 1 .
Table 22. Removal steps of Intel Turbo Memory Minicard or wireless USB adapter (continued) 3 When installing: In models with the wireless USB adapter, plug the yellow cable into the jack on the card.
1130 Bluetooth daughter card (BDC-2.1) For access, remove these FRUs in order: v “1020 Battery pack” on page 63 v “1060 Keyboard” on page 72 v “1080 Palm rest” on page 76 Table 23. Removal steps of Bluetooth daughter card 1 2 3 Step Screw (quantity) Color 1 M2 × 3.5 mm, wafer-head, nylon-coated (1) Silver Torque 0.181 Nm (1.85 kgfcm) When installing: Make sure that the connector 2 is attached firmly.
Table 23. Removal steps of Bluetooth daughter card (continued) Turn the Bluetooth daughter card over, and then disconnect the cable from the connector. 4 When installing: Make sure that the connector 4 is attached firmly.
1140 Keyboard bezel For access, remove these FRUs in order: v “1010 Digitizer pen” on page 62 v “1020 Battery pack” on page 63 v “1060 Keyboard” on page 72 v “1080 Palm rest” on page 76 Table 24. Removal steps of keyboard bezel 1 2 2 2 2 1 1 90 Step Screw (quantity) Color Torque 1 M2 × 6 mm, wafer-head, nylon-coated (3) Black 0.181 Nm (1.85 kgfcm) 2 M2 × 3.5 mm, wafer-head, nylon-coated (4) Silver 0.181 Nm (1.
Table 24. Removal steps of keyboard bezel (continued) 3 Step Screw (quantity) Color Torque 3 M2 × 2 mm, wafer-head, nylon-coated (1) Black 0.181 Nm (1.85 kgfcm) Rotate the LCD unit as shown in this figure.
Table 24. Removal steps of keyboard bezel (continued) In step 5 , detach the claws. Then remove the keyboard bezel in the direction shown by arrow 6 . Attention: handling. When you service the keyboard bezel, avoid any kind of rough 5 5 6 5 5 6 When installing: Make sure that all the claws are attached firmly.
1150 I/O card assembly For access, remove these FRUs in order: v “1010 Digitizer pen” on page 62 v “1020 Battery pack” on page 63 v “1060 Keyboard” on page 72 v “1080 Palm rest” on page 76 v “1110 PCI Express Mini Card for wireless WAN” on page 84 v “1140 Keyboard bezel” on page 90 Table 25. Removal steps of I/O card assembly 1 2 4 5 3 Step Screw (quantity) Color 5 M2 × 3.5 mm, wafer-head, nylon-coated (1) Silver Torque 0.181 Nm (1.
Table 25. Removal steps of I/O card assembly (continued) Note: The cable is secured with a double-faced adhesive tape. 7 6 Turn the I/O card over, and then disconnect the cable from the flip-lock ZIF connector.
1160 USB sub card For access, remove these FRUs in order: v “1010 Digitizer pen” on page 62 v “1020 Battery pack” on page 63 v “1060 Keyboard” on page 72 v “1080 Palm rest” on page 76 v “1140 Keyboard bezel” on page 90 Table 26. Removal steps of USB sub card 2 1 3 2 4 Step Screw (quantity) Color Torque 1 M2 × 6 mm, wafer-head, nylon-coated (1) Silver 0.181 Nm (1.
Table 26. Removal steps of USB sub card (continued) Turn the USB sub card over, an then disconnect the cable from the connector. 5 6 5 When installing: Route the cable as shown in this figure.
1170 LCD assembly For access, remove these FRUs in order: v “1010 Digitizer pen” on page 62 v “1020 Battery pack” on page 63 v “1050 Hinge caps” on page 70 v “1060 Keyboard” on page 72 v “1070 Extension cable card” on page 75 v “1080 Palm rest” on page 76 v “1100 PCI Express Mini Card for wireless LAN” on page 80 v “1110 PCI Express Mini Card for wireless WAN” on page 84 v “1120 Intel Turbo Memory Minicard or wireless USB adapter” on page 86 v “1140 Keyboard bezel” on page 90 Table 27.
Table 27. Removal steps of LCD assembly (continued) 2 2 98 Step Screw (quantity) 2 M2.5 × 6 mm, wafer-head, nylon-coated (2) Black ThinkPad X200 Tablet Hardware Maintenance Manual Color Torque 0.
Table 27. Removal steps of LCD assembly (continued) Before step 3 , strip off the tapes securing the antenna cables, and release the cables from the cable guides of the frame.
Table 27. Removal steps of LCD assembly (continued) When installing: Route the antenna cables along the cable guides and secure them with the tapes. As you route the cables, make sure that they are not subjected to any tension. Tension could cause the cables to be damaged by the cable guides, or a wire to be broken.
1180 DC-in connector, fan, digitizer pen case, and pen switch assembly For access, remove these FRUs in order: v “1010 Digitizer pen” on page 62 v “1020 Battery pack” on page 63 v “1050 Hinge caps” on page 70 v “1060 Keyboard” on page 72 v “1070 Extension cable card” on page 75 v “1080 Palm rest” on page 76 v “1100 PCI Express Mini Card for wireless LAN” on page 80 v “1110 PCI Express Mini Card for wireless WAN” on page 84 v “1130 Bluetooth daughter card (BDC-2.
Table 28. Removal steps of DC-in connector, fan, digitizer pen case, and pen switch assembly (continued) 3 4 102 Step Screw (quantity) 4 M2 × 3.5 mm, wafer-head, nylon-coated (1) Black ThinkPad X200 Tablet Hardware Maintenance Manual Color Torque 0.181 Nm (1.
Table 28. Removal steps of DC-in connector, fan, digitizer pen case, and pen switch assembly (continued) In step 6 and 7 , remove the digitizer pen case assembly. 6 5 7 Step Screw (quantity) Color Torque 5 M1.6 x 3 + 4.2A mm, shoulder socket-head, Black nylon-coated (1) 0.181 Nm (1.85 kgfcm) 6 M2 × 3.5 mm, wafer-head, nylon-coated (1) Silver 0.181 Nm (1.
Table 28. Removal steps of DC-in connector, fan, digitizer pen case, and pen switch assembly (continued) 8 8 8 8 8 8 Step Screw (quantity) Color 8 M2 × 3.5 mm, wafer-head, nylon-coated (6) Silver Torque 0.181 Nm (1.85 kgfcm) 9 10 11 When installing: Make sure that the position of the wireless switch, and firmly fit into the frame b .
Table 28. Removal steps of DC-in connector, fan, digitizer pen case, and pen switch assembly (continued) Turn the system board over, and then disconnect the DC-in connector, the fan connector, and the pen switch connector from the system board. 12 14 13 When installing: Make sure that the DC-in connector, the fan connector, and the Pen switch connector are attached to the system board firmly. 17 16 15 18 19 Step Screw (quantity) Color Torque 18 M2 × 3.
Table 28. Removal steps of DC-in connector, fan, digitizer pen case, and pen switch assembly (continued) When installing: v Before you attach the fan assembly to the computer, apply thermal grease, at an amount of 0.2 grams, on the part marked a as in the following figure. Either too much or too less application of grease can cause a thermal problem due to imperfect contact with a component. You need to peel the thin film off from the rubber b .
1190 System board and ExpressCard slot assembly Important notices for handling the system board: When handling the system board, bear the following in mind. v The system board has an accelerometer, which can be broken by applying several thousands of G-forces. Note: Dropping a system board from a height of as little as 6 inches so that it falls flat on a hard bench can subject the accelerometer to as much as 6,000 G’s of shock.
Table 29. Removal steps of system board and ExpressCard slot assembly Following components soldered on the system board are extremely sensitive. When you service the system board, avoid any kind of rough handling.
Table 29. Removal steps of system board and ExpressCard slot assembly (continued) Note: The ExpressCard slot assembly is attached to the system board. 1 Step Screw (quantity) Color 1 M2 × 3.5 mm, wafer-head, nylon-coated (1) Silver Torque 0.181 Nm (1.85 kgfcm) Turn the system board over, and then remove the ExpressCard slot assembly from the system board.
1200 Base cover and speaker assembly For access, remove these FRUs in order: v “1010 Digitizer pen” on page 62 v “1020 Battery pack” on page 63 v “1050 Hinge caps” on page 70 v “1060 Keyboard” on page 72 v “1070 Extension cable card” on page 75 v “1080 Palm rest” on page 76 v “1100 PCI Express Mini Card for wireless LAN” on page 80 v “1110 PCI Express Mini Card for wireless WAN” on page 84 v “1130 Bluetooth daughter card (BDC-2.
Applying labels to the base cover: The new base cover FRU is shipped with a kit containing labels of several kinds. When you replace the base cover, you need to apply the following labels: 2 Homologation label 12 Product label Following labels need to be peeled off from the old base cover, and need to be put on the new base cover.
2010 LCD front bezel For access, remove this FRU: v “1020 Battery pack” on page 63 Table 31. Removal steps of LCD front bezel for Tablet Digitizer Pen model Tablet Digitizer Pen model: 1 1 1 1 1 Step Screw cap Screw (quantity) M2.5 × 8 mm, wafer-head, nylon-coated (5) 1 2 3 2 112 ThinkPad X200 Tablet Hardware Maintenance Manual Color Torque Black 0.
Table 31. Removal steps of LCD front bezel for Tablet Digitizer Pen model (continued) 4 When installing: Attach the fingerprint reader connector firmly.
Table 32. Removal steps of LCD front bezel for Touch panel and Tablet Digitizer Pen model Touch panel and Tablet Digitizer Pen model: 1 1 2 1 1 2 2 1 1 1 1 1 2 2 2 Step Screw cap Screw (quantity) Color Torque 1 M2.5 × 8 mm, wafer-head, nylon-coated (9) Black 0.392 Nm (4 kgfcm) 2 M2 × 3.5 mm, wafer-head, nylon-coated (6) Black 0.181 Nm (1.85 kgfcm) In step 3 , detach the claws. Then remove the LCD front bezel. Note: The LCD front bezel is secured with a double-faced adhesive tape.
Table 32. Removal steps of LCD front bezel for Touch panel and Tablet Digitizer Pen model (continued) 4 4 5 When installing: Make sure that attach the fingerprint reader connector firmly.
2020 Micro-Processor card For access, remove these FRUs in order: v “1020 Battery pack” on page 63 v “2010 LCD front bezel” on page 112 Table 33. Removal steps of Micro-Processor card Note: Step 1 is only for models with the inverter card. For models without the inverter card, skip step 1 . In step 1 , detach the connector from the inverter card. 1 When installing: Make sure that the connector 1 is attached firmly.
Table 33. Removal steps of Micro-Processor card (continued) 2 3 2 2 Step Screw (quantity) Color Torque 2 M2 × 3.5 mm, wafer-head, nylon-coated (3) Silver 0.181 Nm (1.85 kgfcm) 3 M2 × 3 mm, stud, wafer-head, nylon-coated Black (1) 0.181 Nm (1.85 kgfcm) Note: In step 3 , The height of stud head for Tablet Digitizer pen model is 4.2 mm, and the height of stud head for Touch Panel and Tablet Digitizer Pen model is 5.5 mm.
2030 Inverter card For access, remove these FRUs in order: v “1020 Battery pack” on page 63 v “2010 LCD front bezel” on page 112 v “2020 Micro-Processor card” on page 116 Table 34. Removal steps of inverter card Note: Some models do no have the inverter card. 1 2 1 3 Step Screw (quantity) Color 1 M2 × 3.5 mm, wafer-head, nylon-coated (2) Silver Torque 0.181 Nm (1.85 kgfcm) When installing: Make sure that the connector 3 is attached firmly.
2040 Hinges For access, remove these FRUs in order: v “1010 Digitizer pen” on page 62 v “1020 Battery pack” on page 63 v “1050 Hinge caps” on page 70 v “1060 Keyboard” on page 72 v “1070 Extension cable card” on page 75 v “1080 Palm rest” on page 76 v “1100 PCI Express Mini Card for wireless LAN” on page 80 v “1110 PCI Express Mini Card for wireless WAN” on page 84 v “1120 Intel Turbo Memory Minicard or wireless USB adapter” on page 86 v “1140 Keyboard bezel” on page 90 v “1170 LCD assembly” on page 97 v “2
Table 35. Removal steps of hinge (continued) Detach the hinge from the LCD rear cover, and gently pull the cables out through the guide hole in the hinge. Pull them all at once. As you pull them, be sure not to subject them to any tension, which could cause them to be damaged by the cable guides, or could break a wire.
2050 LCD panel and LCD cable For access, remove these FRUs in order: v “1010 Digitizer pen” on page 62 v “1020 Battery pack” on page 63 v “1050 Hinge caps” on page 70 v “1060 Keyboard” on page 72 v “1070 Extension cable card” on page 75 v “1080 Palm rest” on page 76 v “1100 PCI Express Mini Card for wireless LAN” on page 80 v “1110 PCI Express Mini Card for wireless WAN” on page 84 v “1120 Intel Turbo Memory Minicard or wireless USB adapter” on page 86 v “1140 Keyboard bezel” on page 90 v “1170 LCD assembly
Table 36. Removal steps of LCD panel and LCD cable for Tablet Digitizer Pen model Tablet Digitizer Pen model: 1 2 1 2 1 2 1 3 2 2 2 3 3 Step Color Torque 1 M2.5 × 8 mm, wafer-head, nylon-coated (4) Black 0.392 Nm (4 kgfcm) 2 M2 × 3.5 mm, wafer-head, nylon-coated (6) Black 0.181 Nm (1.85 kgfcm) M2 × 3.5 mm, wafer-head, nylon-coated (3) Silver 0.181 Nm (1.
Table 36. Removal steps of LCD panel and LCD cable for Tablet Digitizer Pen model (continued) In step 4 , detach the claws. Then remove the LCD panel . 4 4 4 4 4 4 4 4 4 4 When installing: Make sure that all the claws are attached firmly.
Table 36. Removal steps of LCD panel and LCD cable for Tablet Digitizer Pen model (continued) Note: Step 5 is only for models with the integrated camera. For models without the integrated camera, skip step 5 . 6 5 When installing: Make sure that the connector 5 is attached firmly.
Table 36. Removal steps of LCD panel and LCD cable for Tablet Digitizer Pen model (continued) Turn the LCD panel over, and then remove the LCD cable from the LCD panel. 7 8 10 9 When installing: Make sure that the LCD cable connector are attached firmly.
Table 37. Removal steps of LCD panel and LCD cable for Touch panel and Tablet Digitizer Pen model Touch panel and Tablet Digitizer Pen model: 1 1 1 1 126 Step Screw (quantity) 1 M2 × 3.5 mm, wafer-head, nylon-coated (4) Silver ThinkPad X200 Tablet Hardware Maintenance Manual Color Torque 0.181 Nm (1.
Table 37. Removal steps of LCD panel and LCD cable for Touch panel and Tablet Digitizer Pen model (continued) Note: Step 2 is only for models with the integrated camera. For models without the integrated camera, skip step 2 . 2 When installing: Make sure that the connector 2 is attached firmly.
Table 37. Removal steps of LCD panel and LCD cable for Touch panel and Tablet Digitizer Pen model (continued) Turn the LCD panel over, and then remove the LCD cable from the LCD panel. 4 5 7 6 When installing: Make sure that the LCD cable connector are attached firmly.
2060 Integrated camera For access, remove these FRUs in order: v “1010 Digitizer pen” on page 62 v “1020 Battery pack” on page 63 v “1050 Hinge caps” on page 70 v “1060 Keyboard” on page 72 v “1070 Extension cable card” on page 75 v “1080 Palm rest” on page 76 v “1100 PCI Express Mini Card for wireless LAN” on page 80 v “1110 PCI Express Mini Card for wireless WAN” on page 84 v “1120 Intel Turbo Memory Minicard or wireless USB adapter” on page 86 v “1140 Keyboard bezel” on page 90 v “1170 LCD assembly” on p
2070 LCD rear cover and wireless antenna cables For access, remove these FRUs in order: v “1010 Digitizer pen” on page 62 v “1020 Battery pack” on page 63 v “1050 Hinge caps” on page 70 v “1060 Keyboard” on page 72 v “1070 Extension cable card” on page 75 v “1080 Palm rest” on page 76 v “1100 PCI Express Mini Card for wireless LAN” on page 80 v “1110 PCI Express Mini Card for wireless WAN” on page 84 v “1120 Intel Turbo Memory Minicard or wireless USB adapter” on page 86 v “1140 Keyboard bezel” on page 90 v
Table 39. Removal steps of LCD rear cover and wireless antenna cables (continued) 3 In step 4 , release the antenna cables from the cable guides of the rear cover.
Table 39. Removal steps of LCD rear cover and wireless antenna cables (continued) 6 6 6 7 6 6 6 Remove the center latch from the LCD rear cover. 1 2 1 132 Step Screw (quantity) 1 M2 × 3.5 mm, wafer-head, nylon-coated (2) Silver ThinkPad X200 Tablet Hardware Maintenance Manual Color Torque 0.181 Nm (1.
Table 39. Removal steps of LCD rear cover and wireless antenna cables (continued) When installing: Place the antenna assembly as shown in this figure. a b c d e f Wireless WAN antenna, AUX (blue) Wireless LAN antenna, AUX (black) Wireless USB antenna (yellow) Wireless WAN antenna, MAIN (red) Wireless LAN antenna, MAIN (gray) MIMO antenna (white) a b c d e f Attention: As you route the antenna cables, make sure that they are not subjected to any tension.
Locations Front view 1 2 3 4 5 6 7 8 9 10 11 12 13 14 Center latch Integrated camera (for some models) Universal serial bus (USB) connector Tablet digitizer pen Hard disk drive (HDD) or solid state drive (SSD) RJ-11 (modem) connector (for some models) Microphone jack Stereo headphone jack Universal serial bus (USB) connector TrackPoint pointing stick TrackPoint buttons Volume control buttons ThinkVantage button Power switch 1 2 14 13 12 11 10 3 4 5 6 7 8 9 134 ThinkPad X20
Rear view 1 2 3 4 5 6 7 8 Status indicators Note: For the description of each indicator, see “Status indicators” on page 50. ExpressCard slot Wireless radio switch Universal Serial Bus (USB) connector RJ-45 (Ethernet) connector External monitor connector AC power connector Security key hole 1 2 5 6 4 3 7 8 Rear view (tablet mode) 1 2 3 Tablet buttons Fingerprint reader Status indicators Note: For the description of each indicator, see “Status indicators” on page 50.
Bottom view 1 2 3 4 5 6 7 Battery pack Battery pack latch Docking connector DIMM slots Built-in speakers LCD cover latch 5-in-1 Media Card Reader or 3-in-1 Media Card Reader slot 1 2 3 7 6 5 136 ThinkPad X200 Tablet Hardware Maintenance Manual 4
Rear view (ThinkPad X200 UltraBase) 1 2 3 4 5 6 7 8 9 10 11 12 13 14 AC power connector Universal serial bus (USB) connectors External monitor connector DisplayPort connector Headphone jack Microphone jack RJ-45 (Ethernet) connector Security keyhole Security lock key Universal serial bus (USB) connector Serial Ultrabay Slim device release latch Serial Ultrabay Slim device eject lever Serial Ultrabay Slim device Docking connector 14 1 13 2 12 11 10 9 7 6 5 4 3 8 ThinkP
Bottom view (ThinkPad X200 UltraBase) 1 2 3 4 5 6 Battery charger (behind the flip-down door) UltraBase eject request button UltraBase eject lever Power button security latch Power button Built-in stereo speakers 1 6 2 5 4 138 ThinkPad X200 Tablet Hardware Maintenance Manual 3
Parts list This section contains following lists of the service parts. v “Overall” on page 140 v “LCD FRUs” on page 154 v “Keyboard” on page 161 v “Miscellaneous parts” on page 162 v “AC adapters” on page 163 v “Power cords” on page 164 v “Recovery discs” on page 165 v “Common service tools” on page 170 Notes: v Each FRU is available for all types or models, unless specific types or models are specified.
Overall 1 32 31 30 2 29 3 4 28 5 25 a 6 7 8 9 10 11 24 12 27 26 13 14 23 15 16 22 17 18 19 20 21 Table 40. Parts list—Overall No. 140 FRU a See “Miscellaneous parts” on page 162. 1 LCD unit (see “LCD FRUs” on page 154.) 2 Extension cable card assembly ThinkPad X200 Tablet Hardware Maintenance Manual FRU no.
Table 40. Parts list—Overall (continued) No. FRU FRU no.
Table 40. Parts list—Overall (continued) No. 142 FRU FRU no. RoHS ID CRU ID 8 System board with Intel Core 2 Duo processor SL9300 42W8049 with TPM (1.
Table 40. Parts list—Overall (continued) No. FRU FRU no.
Table 40. Parts list—Overall (continued) No. 144 FRU FRU no.
Table 40. Parts list—Overall (continued) No. FRU FRU no.
Table 40. Parts list—Overall (continued) No. 146 FRU FRU no.
Table 40. Parts list—Overall (continued) No. FRU FRU no. RoHS ID CRU ID 16 SATA hard disk drive, 160 GB, 9.5 mm, 5,400 rpm OP v 4184-CTO, 25x, E4x, E6x, E7x, F4x, F5x, FBx, FCx, H6x v 7448-CTO, 2Ex, 8Vx, 9Kx, 9Lx, E3x, E5x, E8x, F3x, F5x, FAx, FCx, H5x v 7449-CTO, 25x, 9Ax, 9Ex, 9Fx, E5x, E8x, EWx, EYx, F9x v 7450-CTO, 25x, 2Ax, 2Cx, 2Dx, 2Gx, 8Yx, 93x, E6x, E7x, EXx, EYx, L3x v 7453-CTO, 25x, 2Cx, 2Dx, E6x, E7x v 2263-CTO v 2266-CTO 39T2899 R * 16 SATA hard disk drive, 160 GB, 9.
Table 40. Parts list—Overall (continued) No. 148 FRU FRU no. RoHS ID CRU ID 16 SATA hard disk drive, 250 GB, 9.
Table 40. Parts list—Overall (continued) No. FRU FRU no. RoHS ID CRU ID 16 SATA hard disk drive, 100 GB, 9.5 mm, 7,200 rpm OP v 4184-CTO v 7448-CTO v 7449-CTO, 99x v 7450-CTO, 26x 8Zx, 95x v 7453-CTO v 2263-CTO v 2266-CTO 42T1485 R * 16 SATA hard disk drive, 100 GB, 9.5 mm, 7,200 rpm v 4184-CTO v 7448-CTO v 7449-CTO, 99x v 7450-CTO, 26x 8Zx, 95x v 7453-CTO v 2263-CTO v 2266-CTO 39T2799 R * 16 SATA hard disk drive, 160 GB , 9.
Table 40. Parts list—Overall (continued) No. 150 FRU FRU no.
Table 40. Parts list—Overall (continued) No. FRU FRU no. RoHS ID CRU ID 21 DVD/CD-RW combo drive, 9.5 mm v 4184-CTO v 7448-CTO v 7449-CTO v 7450-CTO v 7453-CTO v 2263-CTO v 2266-CTO 42T2543 R * 21 DVD/CD-RW combo drive, 9.5 mm v 4184-CTO v 7448-CTO v 7449-CTO v 7450-CTO v 7453-CTO v 2263-CTO v 2266-CTO 42T2513 R * 21 DVD-RAM/RW drive, 9.
Table 40. Parts list—Overall (continued) No. 152 FRU FRU no. RoHS ID CRU ID 23 Base cover assembly for 7450 45N3142 R N 23 Base cover assembly for 7453 45N3143 R N 23 Base cover assembly for 2263 45N3144 R N 23 Base cover assembly for 2266 45N3145 R N 24 Bluetooth daughter card (BDC-2.
Table 40. Parts list—Overall (continued) No. FRU FRU no.
LCD FRUs In ThinkPad X200 Tablet, there are following types of LCDs. v “12.1-in.
12.1-in. WXGA TFT Table 41. Parts list—12.1-in. WXGA TFT No. FRU FRU no. RoHS ID CRU ID b - c See “Miscellaneous parts” on page 162.
Table 41. Parts list—12.1-in. WXGA TFT (continued) No. 156 FRU FRU no. RoHS ID CRU ID 3 LCD panel, 12.1-in. WXGA for Tablet Digitizer Pen 45N6090 model v 4184-CTO, 25x, 97x v 7448-CTO, 2Ex, 8Vx, 8Wx, 8Xx, 9Dx, 9Kx, 9Lx v 7449-CTO, 25x, 99x, 9Ax, 9Bx, 9Cx, 9Ex, 9Fx, 9Hx v 7450-CTO, 25x, 26x, 28x, 2Ax, 2Cx, 2Dx, 2Fx, 2Gx, 2Hx, 8Yx, 8Zx, 93x, 94x, 95x, 96x, 9Gx, 9Jx, G9x, GAx, L3x v 7453-CTO, 25x, 2Cx, 2Dx, 98x, 9Gx v 2263-CTO v 2266-CTO R N 3 LCD panel, 12.1-in.
Table 41. Parts list—12.1-in. WXGA TFT (continued) No. FRU FRU no.
Table 41. Parts list—12.1-in. WXGA TFT (continued) No. 158 FRU FRU no.
Table 41. Parts list—12.1-in. WXGA TFT (continued) No. FRU FRU no.
Table 41. Parts list—12.1-in. WXGA TFT (continued) No. 160 FRU FRU no.
Keyboard Table 42. Parts list—Keyboard Language P/N Arabic 42T3752 42T3686 Belgian 42T3749 42T3683 Brazilian Portuguese 42T3768 42T3702 Bulgarian 42T4143 42T4139 Canadian French (058) 42T3739 42T3673 Canadian French (Acnor) 42T3738 42T3672 Czech 42T3757 42T3691 Danish 42T3746 42T3680 Dutch 42T3743 42T3677 Finnish, Swedish 42T3744 42T3678 French 42T3742 42T3676 German 42T3740 42T3674 Greek (U.S.
Miscellaneous parts Table 43. Parts list—Miscellaneous parts FRU P/N RoHS ID CRU ID Screw kit: v M1.6 × 6 mm (sliver), wafer head (1) v M2 × 2.5 mm (black), wafer head (1) v M2 × 3.5 mm (silver), wafer head (18) v M2 × 3.5 mm (black), wafer head (1) v M2 × 3.5 mm (black), flat head (8) v M2 × 6 mm (silver), wafer head (3) v M2 × 6 mm (black), wafer head (12) v M2 x 3 mm, height 4.2 mm, stud (black), wafer head (1) v M2 x 3 mm, height 5.5 mm, stud (black), wafer head (1) v M2.
AC adapters Table 44.
Power cords A ThinkPad power cord for a specific country or region is usually available only in that country or region: Table 45. Parts list—2-pin power cords Region P/N Argentina v models -CTO, xxY 42T5020 42T5105 Brazil v models -CTO, xxP 42T5180 42T5183 Canada, U.S. v models -CTO, xxF, xxL, xxS, xxU 42T5008 42T5093 Japan v models -Exx, Jxx 42T5014 42T5099 RoHS ID CRU ID R * RoHS ID CRU ID R * Table 46.
Recovery discs Windows XP Tablet DVDs Windows XP Tablet is preinstalled as the operating system in the following models: v 4184-CTO, F5x, F8x, FCx, FGx v 7448-CTO, 8Wx, F5x, F8x, FCx, FGx v 7449-CTO, 84x, 8Fx, 8Jx, 8Rx, 9Ex, 9Fx, EYx, F9x, FNx v 7450-CTO, 2Hx, 9Gx, EYx, FDx, FNx, G4x, L3x v 7453-CTO, 9Gx, FDx v 2263-CTO v 2266-CTO Table 47.
Windows Vista Home Premium (32 bit) DVDs Windows Vista Home Premium (32 bit) is preinstalled as the operating system in the following models: v 4184-CTO, 25x, 8Ex, 97x v 7448-CTO, 2Ex, 8Dx, 8Vx, 9Dx, 9Kx, 9Lx v 7449-CTO, 25x v 7450-CTO, 25x v 7453-CTO, 25x v 2263-CTO v 2266-CTO Table 48.
Windows Vista Business (32 bit) DVDs Windows Vista Business (32 bit) is preinstalled as the operating system in the following models: v 4184-CTO, E4x, E6x, E7x, E9x, EFx, EGx, ENx, ESx, F4x, F7x, FBx, FFx, H4x, H6x v 7448-CTO, 8Xx, E3x, E5x, E8x, EAx, EEx, EHx, EPx, EUx, F3x, F6x, FAx, FEx, FKx, G6x, H3x, H5x v 7449-CTO, 88x, 8Lx, 8Qx, 8Sx, 99x, 9Ax, 9Bx, 9Cx, 9Hx, E5x, E8x, EAx, EHx, EPx, EUx, EWx, FLx, FWx, FXx, G5x, G6x v 7450-CTO, 26x 28x 2Ax 2Cx 2Dx 2Fx 2Gx, 86x, 89x, 8Cx, 8Gx, 8Hx, 8Kx, 8Mx, 8Nx, 8Px,
Windows Vista Business (64 bit) DVDs Windows Vista Business (64 bit) is preinstalled as the operating system in the following models: v 4184-CTO v 7448-CTO v 7449-CTO, EKx v 7450-CTO, FYx v 7453-CTO v 2263-CTO v 2266-CTO Table 50.
Windows Vista Ultimate (32 bit) DVDs Windows Vista Ultimate (32 bit) is preinstalled as the operating system in the following models: v 4184-CTO v 7448-CTO v 7449-CTO v 7450-CTO, 8Ax v 7453-CTO v 2263-CTO v 2266-CTO Table 51.
Common service tools Table 52. Parts list—Common service tools Tool P/N Screwdriver kit 95F3598 1/4″ drive spinner handle 1650840 1/4″ Sq. to 1/4″ hex torx adapter 93F2838 TR7-TR-10 tamper resistant torx bits 00P6967 Removal tool antenna RF connector 08K7159 USB 2.
Notices Lenovo may not offer the products, services, or features discussed in this document in all countries. Consult your local Lenovo representative for information on the products and services currently available in your area. Any reference to a Lenovo product, program, or service is not intended to state or imply that only that Lenovo product, program, or service may be used.
vary significantly. Some measurements may have been made on development-level systems and there is no guarantee that these measurements will be the same on generally available systems. Furthermore, some measurements may have been estimated through extrapolation. Actual results may vary. Users of this document should verify the applicable data for their specific environment.
Part Number: 45N3683_01 (1P) P/N: 45N3683_01
