User's Manual

ManualsBrandsLenoxx ManualsCD PlayerLenoxx CD-160

ANTENNASANTENNAS

ANTENNAS

The built-in AM Antenna and the FM Telescoping Antenna are directional. You may find

that you can improve AM reception by rotating the set or bringing it closer to a window. The

FM Band can be adjusted by FM Telescoping Antenna. Be sure to extend the FM Telescoping

Antenna carefully to its full length for best reception.

O LISTEN TO LISTEN T

O LISTEN T

O PRESETO PRESET

O PRESET

MEMOR MEMOR

MEMOR

ST ST

TIONS (after youTIONS (after you

TIONS (after you

programmed them)programmed them)

programmed them)

1. Press the Power Switch ON, the Power/Batt. Lamp will light.

2. Press the Radio Switch, the Radio Indicator will light.

3. Press the Band Switch to select the band you want (AM or FM).

4. Press the Radio Presets Button to select the stations stored (01-10). You will receive

the station you stored into that preset memory. Pressing the button several times will

give you the different preset stations you stored into the preset memories 1 to 10

(Example: Pressing the button 3 times will give you Preset Number 3, press the button

4 times will give you Preset Number 4). Word 

PRESET

 and Preset Number will show in

the Display.

5. To shut off the radio, press the Power Switch again, the Power/Batt. Lamp will go off.

RADIO OPERARADIO OPERA

RADIO OPERA

TIONTION

TION

O PLAO PLA

O PLA

THE RADIO THE RADIO

THE RADIO

PRESETTING STPRESETTING ST

PRESETTING ST

TIONSTIONS

TIONS

UPUP

T T

O 10 AM AND 10 FM STO 10 AM AND 10 FM ST

O 10 AM AND 10 FM ST

TIONS CAN BE STTIONS CAN BE ST

TIONS CAN BE ST

ORED INTORED INT

ORED INT

O THE PRESETO THE PRESET

O THE PRESET

MEMORIES. (THEYMEMORIES. (THEY

MEMORIES. (THEY

WILL WILL

WILL

REMAIN IN MEMOR REMAIN IN MEMOR

REMAIN IN MEMOR

AS LONG AS THE BA AS LONG AS THE BA

AS LONG AS THE BA

TTERIESTTERIES

TTERIES

ARE INSTARE INST

ARE INST

ALLED, OR AC POWER CORD IS CONNECTED.)ALLED, OR AC POWER CORD IS CONNECTED.)

ALLED, OR AC POWER CORD IS CONNECTED.)

Press the Band Switch to select AM or FM band, and

press the Tuning or Button to select a station.

2. Press the Radio Store (Program) Button, 

PROGRAM



will flash in the Display.

PRESET PROGRAM

Make sure the speakers are connected (speaker wires plugged into the jacks in the back

of the set).

3. While the 

PROGRAM

 is blinking, press the Radio Presets Button to choose a memory

location (01-10). (Example: Push the Radio Presets Button 3 times for Preset Number 3;

4 times for Preset Number 4.)

4. Press the Radio Store (Program) Button again to confirm. The station now broadcasting

is stored into that preset memory.

NOTENOTE

NOTE: Steps 2-4 should be done quickly.

5. Repeat the above steps 1 to 4 to store other 9 stations into memory.

6. Each memory location (01-10) can store 2 stations, one for AM, the other for FM.

NOTE:NOTE:

NOTE: Before you disconnect the power (AC and Battery) of the set, make sure the

Power Switch is OFF, then you have approximately 30 seconds to re-connect

the power. Otherwise, the memories may be lost and need to be re-programmed.

1. Press the Power Switch ON (the Power Lamp will light).

2. Press the Radio Switch ON (the Radio Indicator will light).

3. Press the AM/FM Band Switch to select the desired wave band.

4. Tune to desired station by pressing the Tuning or Button. Each time the

button is pressed, the frequency changes.

5. To search for a station quickly (automatic tuning), keep the Tuning or Button

pressed until the station starts to change rapidly, then release the Button and it will stop

at the next strong station.

6. If you tune into a FM stereo station, 

 will

show in the Display.

7. Adjust the Volume Control to your listening preference.

8. If you prefer more bass, slide the Bass Boost Switch to ON position.

9. To turn off the radio, press the Power Switch again, the Power Lamp will go off.

CD-160S050699 V.2