MODEL : CD7400N STEREO 3CD MINI HI-FI SYSTEM WITH PLL RADIO CASSETTE AND TURNTBLE INSTRUCTION MANUAL
IMPORTANT SAFETY INSTRUCTIONS: 1. Read the instructions. All uses guidelines must be read before start device. 2. Keep the instructions for future use. 3. Attention, use and security guidelines must be respected. 4. The device must not be used near water or be put in contact with moisture. 5. Make sure has no liquid is spilled on device and device openings. 6. Move device carefully, avoid shocks. 7. Do not block the breakdown of the device outputs. 8. Do not place the device near from a heat source (e.g.
BATTERY INSTALLATION The battery compartment is located on the back of the remote control. 1. Remove the battery compartment door by pressing in on the tab and lifting it off. 2. Insert two (2) AAA size batteries (not included) into the battery compartment following the polarity markings inside the battery compartment. 3. Replace the battery compartment door. Battery Precautions Replacement of batteries must be done by an adult. Do not mix old and new batteries.
LOCATION OF CONTROLS 1) 2) 3) 4) 5) 6) 7) 8) 9) 10) 11) 12) 13) 14) Dust cover LCD display Volume up-down button Extra bass control button Standby LED indicator FM mode / Dubbing speed selector On/Standby button CD stop button Mute button CD button Sleep / Timer button 19) Remote sensor 20) Pre-set EQ button 21) CD play / pause button 22) Disc skip button 23) Phono button 24) Tuner/Band button 25) Tape button 26) CD tray open/close button 27) Skip / Search / Tuning up button 28) Repeat / M-up button 29)
Connection 1. 2. 3. Connect the speaker wire from included speaker box to the speaker terminal (35) of the main unit. Connect the power cord (37) to AC outlet, the unit will go into standby mode and Standby LED (5) lights up. Turn on the unit by On/Standby button (7). If the LCD display (2) is on with backlighting, it means the power supply is normal. Now your system is ready to play the music. Setting the clock 1. 2. 3. 4. Set unit in standby mode by On/Standby button (7).
1. 2. 3. 4. 5. 6. 7. 8. Press Phono button ( 23) Set the speed selector (32) to the proper position depending on the record to be played. Place the record on the platter (use the spindle adaptor (31) if required). Lift the tone arm from the rest and slowly move it to the record side. The platter will being to rotate. Place the tone arm to the desired position of the record. Adjust the volume to the desired level. At the end of record, the platter will automatically stop rotating.
1. 2. 3. 4. 5. 6. 7. 8. Set in CD mode. Press the Mem/clk-adj. button (14) Press the Disc skip button (22) to select the desired disc. Press skip or button (12/27) to select the desired track. Press the Mem/clk/adj. button (14) again to store the track in memory. Repeat steps 3 to 5 to enter additional program Press Play/Pause button (21) to start playback in order. Press Stop button (8) to stop playback and press again to clear all programmed tracks.
D. Recording from turntable press Phono button (23) to active turntable mode Insert a blank cassette tape in deck 1. press Record & Play key to start recording. Select the desire record and start playback Press Pause keys and then Stop/Eject key when finish. More features A. Sleep setting 1. Press & hold the Sleep/Timer button (11), to active & adjust the sleep timer in the order of 90 > 80 >70….10 minutes automatically. 2.
REMOTE CONTROL TRANSMITTER CONTROL FUNCTIONS Battery installation (battery not provided) the infra-red transmitter require 2 pcs “ AAA “ battery for operation Button description Open/Close Press to open & close the CD door On/Standby Press to switch the system into standby mode Disc 1,2,3 Press to select the disc for playback directly Disc-ch Press to select the next desire disc and rotate the disc tray Sleep Press to active sleep function Timer Press to set the alarm mode on/off Phono Press t
LEADERS IN SOUND ENTERTAINMENT Lenoxx Electronics (Aust) Pty Ltd 6 Oban Court Laverton North 3026 Tel: + 61 3 9267 2100 - Fax: + 61 3 9267 2199 Email Address: lenoxx@lenoxx.com.au Web site: www.lenoxxelectronics.
