User Manual

Connection
1. Connect the speaker wire from included speaker box to the speaker terminal (35) of the main unit.
2. Connect the power cord (37) to AC outlet, the unit will go into standby mode and Standby LED (5) lights up.
3. Turn on the unit by On/Standby button (7). If the LCD display (2) is on with backlighting, it means the power supply
is normal. Now your system is ready to play the music.
Setting the clock
1. Set unit in standby mode by On/Standby button (7).
2. Press the “Mem/clk-adj” button (14), the first second digit of “00” is flashing. press or button (12/27) to
set the correct hour. Press ”Mem/clk-adj” button (14) to store the correct hour.
3. The third & fourth digit of “00” is flashing, press the
or button (12/27) to set the correct minutes. Press
“Mem/clk-adj” (14) to store the correct minute.
4. To select 12/24 hours display mode, hold the CD stop button (8) to change mode repeatedly.
 the pre-set time will be re-set completely if switching off the main power button on system.
you are recommended to switch the system into standby mode for convenience usage.
Listening to radio
Manual tuning
1. Set unit in standby mode by On/Standby button (7).
2. Press Tuner/band button repeatedly ( 24) to select tuner mode and desired band(FM-AM).
3. Tune to the required station by pressing the Tuning up/down button (12/27).
4. Adjust volume controls to the desired volume level.
Auto tuning
1. Press Tuner/Band button (24) and select tuner mode and desired band.
2. Press and hold the Tuning up/down button (12/27) for 1-2 seconds and then release
3. The unit will start seeking automatically and stop until a radio station is reached.
4. Repeat step 2 & 3 until the desired radio station is being reached.
5. Adjust volume controls to the desired volume level.
Preset stations
You can store up to total of 40 radio stations in the memory (FM-20/AM-20).
1. Set to radio mode
2. Turn to the desired radio station by “ Manual” or “Auto” tuning method.
3. Press “Mem/clk-adj” button (14) to enable program state.
4. Press “Repeat/M-up” button (28) to select the desired station memory for storage.
5. Press “Mem/clk-adj” button (14) again to confirm the setting.
6. Repeat step 2 to 5 to store other stations.
7. Press “M-up” or “M-dn” button (28/13) to select the preset stations in order.
8. To return normal tuner mode, leave keys free.
 The pre-set memories will be cancelled completely if disconnect the main power of the system. You are
recommended to switch the system into standby mode for convenience usage.
 There are 10 seconds for program state, after 10 sec. this state would release to normal tuner mode
automatically.
 you can overwrite a present station by storing another frequency in its place.
FM & FM-stereo reception
 Set the FM mode selector (6) at “MONO” position. Programs are received in mono mode. In particular when
stereo signals are weak. It is preferable to receive the program in mono.
 Set the FM mode selector (6) at “ST” position for receiving stereo programs. The “ST” indicator will appear on
LCD to show FM stereo program is receiving.
- FM : The receiver has a build-in FM wire antenna hanging at the rear cabinet. This wire should be totally
unraveled and extended for best reception.
- AM : The receiver has a built-in AM bar antenna. If AM reception is weak, slightly rotate or re-positioning of the
unit will usually improve the am reception.
Phono
noted:
- Remove the stylus protector.
- Be sure that the tone arm is being detached from the tone arm rest before
operating, and re-secured again afterwards.
2