BIG BUTTON MEMORY PHONE WITH VOLUME CONTROL MODEL: PH-417 OPERATING INSTRUCTIONS • BIG BUTTONS FOR EASIER VIEWING & DIALING • RECEIVER VOLUME CONTROL • 3 ONE-TOUCH MEMORY BUTTONS • INCOMING CALL INDICATOR LAMP • FLASH & REDIAL/PAUSE BUTTON • TONE/PULSE SWITCHABLE DIALING • DESK OR WALL MOUNTABLE • 15 FOOT EXTRA LONG COIL CORD PLEASE READ CAREFULLY BEFORE USE IB-PH417-WM-E-022804 IB-PH417(MS)-WM-E-022804.
IMPORTANT SAFETY INSTRUCTIONS When using your telephone equipment, the following basic safety precautions should always be followed to reduce the risk of fire, electric shock and personal injury: 1. Read and follow all instructions and warnings. 2. Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a slightly dampened cloth only. 3.
IMPORTANT TELEPHONE COMPANY & FCC INFORMATION CAUTION: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK AND PERSONAL INJURY, DO NOT OPEN CABINET. WE SUGGEST THAT YOU REVIEW THE FOLLOWING INFORMATION PROVIDED BY THE FCC (FEDERAL COMMUNICATIONS COMMISSION). FCC REGISTRATION This telephone set is registered with the FCC based upon compliance with Part 68 of its rules.
CHECK LIST Unpack your set, you should find: MAIN SET HANDSET 15 FOOT HANDSET CORD (coil cord) STRAIGHT TELEPHONE CORD SHORT STRAIGHT CORD (for wall mounting) 3 IB-PH417(MS)-WM-E-022804.
LOCATION OF CONTROLS 16 1 15 10 11 12 14 13 2 9 3 8 4 7 5 6 1. COMFORTABLE ROUNDED HANDSET 2. 3 ONE-TOUCH MEMORY buttons - Allows you to speed dial emergency or other frequently dialed numbers. 3. EXTRA LARGE KEYPAD buttons - For easier viewing & dialing. 4. REDIAL/PAUSE button - Redials your last number, useful when line is busy. And also useful when dialing the number with pause. 5. INCOMING CALL INDICATOR lamp - Flashes when phone rings to show you call is coming in. 6.
INSTALLATION INSTRUCTIONS INSTALLATION TO TELEPHONE WALL JACK HANDSET REAR OF THE TELEPHONE BASE COILED HANDSET CORD STRAIGHT TELEPHONE CORD To Telephone Jack 1. Insert the modular plugs of the COILED HANDSET CORD into the jack of the TELEPHONE HANDSET and into the jack on the left side of the TELEPHONE BASE. 2. Insert the modular plugs of the STRAIGHT TELEPHONE CORD into the modular jack at the REAR of the TELEPHONE BASE and into the TELEPHONE WALL JACK (either end can be plugged in).
PHONE OPERATION RECEIVING CALLS AS A NORMAL TELEPHONE When the phone rings: 1. Lift the HANDSET and speak into the mouthpiece of the HANDSET. 2. Hang up the HANDSET when the conversation is completed. MAKING CALLS AS A NORMAL TELEPHONE 1. Select the desired dialing mode with the TONE/PULSE switch (do this only the first time). 2. Pick up the HANDSET and listen for a dial tone. 3. Dial your call.
STORING PHONE NUMBER INTO MEMORY LOCATIONS NOTE 1. This phone has 3 ONE-TOUCH memories. This is very useful for emergency numbers or numbers you call very often such as your parents or best friends. To use the one-touch numbers, just get a dial tone and press one of the 3 buttons. To store a number into any of these 3 locations, just follow the instructions below. Remember to write the names you stored onto the Memory Index Card. NOTE 2. It is important to write the emergency numbers into the Memory Index.
STORING TELEPHONE NUMBERS INTO MEMORY LOCATIONS NOTE 1. If you want to store a calling card number into one of your memories, you may do this the same way you program a phone number into memory. Also if you need a pause in the number, simply press the REDIAL/PAUSE button on your phone. NOTE 2. Emergency calling is an important safety feature that should be used wisely. If you program an emergency number into the memory - mark it clearly and test it before an emergency.
WALL MOUNTING The set can be mounted on a wall phone plate. If you do not have a modular wall phone plate installed, we recommend that you consult with your telephone company or installer to get one, or turn to page 10 for instruction. 1. Reversible HANDSET HOLDER - When the telephone is mounted on the wall, the REVERSIBLE HANDSET HOLDER must be adjusted so it will hold the handset. 2.REVERSE 1.SLIDE OUT 3.REPLACE INTO PHONE CONNECTING TO WALL PLATE 1. Use the SHORT STRAIGHT cord. 2.
WALL MOUNTING FOLLOW THESE INSTRUCTIONS TO MOUNT THE PHONE ON THE WALL WITHOUT A WALL PLATE Follow these instructions to mount the phone on the wall without a wall plate: 1. Locate a wall stud. If it is possible to utilize a wall stud for mounting, dry wall expanders or a similar type fastener is recommended. Consult your local hardware stores for details. 2. Drill 2 holes 3 15/ 16" (100 mm) apart. 3.
TROUBLE SHOOTING PROBLEM LIKELY CAUSES 1. 2. 1. 2. 3. No dial tone. Phone is dead. Plug disconnected from jack. Jack improperly wired. Damaged cord. Jack improperly wired. Line out of order. Can make calls, but phone does not ring. RINGER switch in OFF position. Slide the switch to ON position. Can receive, but cannot make calls. 1. If your other telephones are “ROTARY” type phones, your line may be conditioned to accept PULSE dialing only. Move TONE/PULSE switch to PULSE position. 2.
LIMITED WARRANTY We warrant this product to be free from defects in material and workmanship under normal use for a period of 1 year after purchase and we will repair it free of charge or replace it at no charge, should it become defective under this warranty, providing you submit proof of purchase (sales slip) with the set. During the initial 1 year period after original purchase, we will service or exchange, at no charge, the set that is returned to LENOXX ELECTRONICS CORP.
