Instruction Manual

Lenze · Decentralised frequency inverter 8400 motec (EtherNet/IP™ option) · EDS84DMOTEIP EN 2.0 - 10/2013 88
Error messages
Mapping of Lenze device errors to DRIVECOM errors
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
xx.0123.00090 OC13: Maximum current for Fch exceeded 0x2000 0x2000 Current
xx.0123.00093 OT2: Speed controller output is limited 0xF000 0x7310 Speed
xx.0123.00094 FC01: Switching frequency reduction 0x2000 0xF000 Additional functions
xx.0123.00095 FC02: Maximum speed for Fchop 0xF000 0xF000 Additional functions
xx.0123.00096 OC14: Limitation direct-axis current controller 0xF000 0xF000 Additional functions
xx.0123.00097 OC15: Limitation cross current controller 0xF000 0xF000 Additional functions
xx.0123.00098 OC16: Limitation torque controller 0xF000 0xF000 Additional functions
xx.0123.00099 FC03: Limitation field controller 0xF000 0xF000 Additional functions
xx.0123.00105 OC6: I2xt overload - motor 0x2000 0x7120 Motor
xx.0123.00145 LP1: Motor phase failure 0x3000 0x3130 Phase Failure
xx.0123.00200 SD10: Speed limit - feedback system 12 0x7300 0x7300 Sensor
xx.0123.00201 SD11: Speed limit - feedback system 67 0x7300 0x7300 Sensor
xx.0123.00205 SD3: Open circuit - feedback system 0x7300 0x7301 Tacho defective
xx.0125.00001 An01: AIN1_I < 4 mA 0xF000 0xF000 Additional functions
xx.0125.00002 An02: AIN2_I < 4 mA 0xF000 0xF000 Additional functions
xx.0126.00001 Ab01: Axis bus timeout 0x8000 0x8000 Monitoring
xx.0126.00002 Ab02: Axis bus IO error 0x8100 0x8100 Communication
xx.0127.00002 CE04: MCI communication error 0x7000 0x7500 Communication
xx.0127.00015 CE0F: MCI control word 0xF000 0xF000 Additional functions
xx.0131.00000 CE4: CAN Bus Off 0x8000 0x8000 Monitoring
xx.0131.00006 CA06: CAN CRC error 0x8000 0x8000 Monitoring
xx.0131.00007 CA07: CAN Bus Warn 0x8000 0x8000 Monitoring
xx.0131.00008 CA08: CAN Bus Stopped 0x8000 0x8000 Monitoring
xx.0131.00011 CA0b: CAN HeartBeatEvent 0x8130 0x8000 Monitoring
xx.0131.00015 CA0F: CAN control word 0xF000 0x8000 Monitoring
xx.0135.00001 CE1: CAN RPDO1 0x8100 0x8100 Communication
xx.0135.00002 CE2: CAN RPDO2 0x8100 0x8100 Communication
xx.0135.00003 CE3: CAN RPDO3 0x8100 0x8100 Communication
xx.0135.00004 CP04: CAN RPDO4 0x8100 0x8100 Communication
xx.0140.00013 CI01: Module missing/incompatible 0x7000 0x7000 Additional Modules
xx.0144.00001 PS01: No memory module 0x6300 0x6300 Date Set
xx.0144.00002 PS02: Par. set invalid 0x6300 0x6300 Date Set
xx.0144.00003 PS03: Par. set device invalid 0x6300 0x6300 Date Set
xx.0144.00004 PS04: Par. set device incompatible 0x6300 0x6300 Date Set
xx.0144.00007 PS07: Par. mem. module invalid 0x6300 0x6300 Date Set
xx.0144.00008 PS08: Par. device invalid 0x6300 0x6300 Date Set
xx.0144.00009 PS09: Par. format invalid 0x6300 0x6300 Date Set
xx.0144.00010 PS10: Memory module link invalid 0x5000 0x5000 Device Hardware
xx.0144.00031 PS31: Ident. error 0x6300 0x6300 Date Set
xx.0145.00014 dF14: SW-HW invalid 0x5530 0x6000 Device software
xx.0145.00015 dF15: DCCOM CU2 error 0x6100 0x6100 Internal software
xx.0145.00024 dF18: BU RCOM error 0x6100 0x6100 Internal software
xx.0145.00025 dF25: CU RCOM error 0x6100 0x6100 Internal software
xx.0145.00026 dF26: Appl. watchdog 0x6200 0x6010 Software reset (watchdog)
xx.0145.00033 dF21: BU watchdog 0x6100 0x6010 Software reset (watchdog)
xx.0145.00034 dF22: CU Watchdog 0x6100 0x6010 Software reset (watchdog)
xx.0145.00035 dF10: AutoTrip reset 0xF000 0xF000 Additional functions
xx.0145.00050 dF50: Retain error 0x6100 0x6100 Internal software
xx.0145.00051 dF51: CuCcr error 0x6100 0x6100 Internal software
xx.0145.00052 dF52: BuCcr error 0x6100 0x6100 Internal software
Lenze error CAN DRIVECOM error
Error number
[32 bits]
Error message Emergency
Error Code
Error number
[hex]
Error message