Ä.6Waä EDK94AYCEC .
Lesen Sie zuerst diese Anleitung, bevor Sie mit den Arbeiten beginnen! Beachten Sie die enthaltenen Sicherheitshinweise. Please read these instructions before you start working! Follow the enclosed safety instructions. Veuillez lire attentivement cette documentation avant toute action ! Les consignes de sécurité doivent impérativement être respectées. Lea las instrucciones antes de empezar a trabajar. Observe las instrucciones de seguridad indicadas.
E94YCEC001A E94YCEP017 klappseite_E94AYCEC−einbaufreiraum
0Abb. 0Tab. 0 Lieferumfang Pos. Beschreibung Kommunikationsmodul E94AYCEC, ETHERNET Powerlink (CN) Montageanleitung Anschlüsse Pos. Beschreibung X250 Anschluss zur externen Versorgung des Kommunikationsmoduls Ausführung: Steckerleiste mit Schraubanschluss, 2−polig X251 Anschluss für ETHERNET Powerlink Ausführung: RJ45−Buchse nach IEC 60603−7, mit integrierten LEDs X252 DIP−Schalter E94YCEP001D Pos.
Anzeigen LED Pos. Farbe Zustand Beschreibung MS grün blinkt Kommunikationsmodul ist mit Spannung versorgt, hat aber keine Verbindung zum Grundgerät (Grundgerät ist ausgeschaltet, in der Initialisierungsphase oder nicht vorhanden). an Kommunikationsmodul ist mit Spannung versorgt und hat Verbindung zum Grundgerät. Es liegt ein Fehler im Bereich des Kommunikationsmoduls vor. ME rot an BS grün Die LED−Funktionen werden durch die NMT−Statemachine gesteuert.
Montage E94YCXX001G Demontage E94AYCXX001H 6 EDK94AYCEC DE/EN/FR/ES/IT 1.
Gültigkeit Diese Anleitung ist gültig für ƒ Kommunikationsmodule E94AYCEC, ETHERNET Powerlink (CN), ab Version VC 1.0 Identifikation Type HW Ver. SW Ver. MAC ID E94YCEI003C E94 A Y C EC VC 1.
1 Sicherheitshinweise Definition der verwendeten Hinweise 1 Sicherheitshinweise Definition der verwendeten Hinweise Um auf Gefahren und wichtige Informationen hinzuweisen, werden in dieser Dokumentation folgende Piktogramme und Signalwörter verwendet: Sicherheitshinweise Aufbau der Sicherheitshinweise: Gefahr! (kennzeichnet die Art und die Schwere der Gefahr) Hinweistext (beschreibt die Gefahr und gibt Hinweise, wie sie vermieden werden kann) Piktogramm und Signalwort Bedeutung Gefahr! Gefahr vo
Sicherheitshinweise 1 Gefahr! Unsachgemäßer Umgang mit dem Kommunikationsmodul und dem Grundgerät kann schwere Personenschäden und Sachschäden verursachen. Beachten Sie die in den Anleitungen zum Grundgerät enthaltenen Sicherheitshinweise und Restgefahren. EDK94AYCEC DE/EN/FR/ES/IT 1.
2 2 Elektrische Installation Elektrische Installation Externe Spannungsversorgung Versorgen Sie das Kommunikationsmodul über den Anschluss X210 mit einer separaten Versorgungsspannung. Bezeichnung Erläuterung + Externe Spannungsversorgung U = 24 V DC (20,4 V − 0 % ... 28,8 V + 0 %) I = 140 mA − Bezugspotential für externe Spannungsversorgung Verwenden Sie bei größeren Entfernungen zwischen den Schaltschränken in jedem Schaltschrank ein Netzteil.
Elektrische Installation 2 Ethernet−Anschluss E94YCEP004C PIN Signal 1 Tx + / Rx + 2 Tx − / Rx − 3 Rx + / Tx + 4 − 5 − 6 Rx − / Tx − 7 − 8 − Hinweis! Bitte verwenden Sie nur handelsüblich vorkonfektionierte Kabel (entsprechend ISO/IEC 11801 bzw. EN 50173): ƒ Kabeltyp S/FTP ƒ Kategorie CAT 5e EDK94AYCEC DE/EN/FR/ES/IT 1.
0Fig. 0Tab. 0 Scope of supply Pos. Description E94AYCEC communication module , ETHERNET Powerlink (CN) Mounting Instructions Connections Pos. Description X250 Connection to the external supply of the communication module Design: plug connector with screw connection, 2−pole X251 Connection for ETHERNET Powerlink Design: RJ45 socket in accordance with IEC 60603−7, with integrated LEDs X252 DIP switch E94YCEP001D Pos.
Displays LED Pos. Colour Condition Description MS Green Blinking Communication module is supplied with voltage, but has no connection to the standard device (standard device is either switched off, in the initialisation phase, or not available). On Communication module is supplied with voltage and has a connection to the standard device. There is an error in the area of the communication module. ME Red On BS Green The LED functions are controlled by the NMT state machine.
Mounting E94YCXX001G Dismounting E94AYCXX001H 14 EDK94AYCEC DE/EN/FR/ES/IT 1.
Validity These instructions are valid for ƒ E94AYCEC communication modules , ETHERNET Powerlink (CN), as of version VC 1.0 Identification Type HW Ver. SW Ver. MAC ID E94YCEI003C E94 A Y C EC VC 1.
1 Safety instructions Definition of notes used 1 Safety instructions Definition of notes used The following pictographs and signal words are used in this documentation to indicate dangers and important information: Safety instructions Structure of safety instructions: Danger! (characterises the type and severity of danger) Note (describes the danger and gives information about how to prevent dangerous situations) Pictograph and signal word Meaning Danger! Danger of personal injury through danger
Safety instructions 1 Danger! Inappropriate handling of the communication module and of the standard device can cause serious injuries to persons and damage to material assets. Observe the safety instructions and residual hazards described in the documentation on the standard device. EDK94AYCEC DE/EN/FR/ES/IT 1.
2 2 Electrical installation Electrical installation External voltage supply Supply the communication module via the connection X210 by means of a separate supply voltage. Designation Explanation + External voltage supply U = 24 V DC (20.4 V − 0 % ... 28.8 V + 0 %) I = 140 mA − Reference potential for external voltage supply For greater distances between the control cabinets, use a power supply unit in each control cabinet. Screw terminal data Plug connector with screw connection rigid: 1.
Electrical installation 2 Ethernet connection E94YCEP004C PIN Signal 1 Tx + / Rx + 2 Tx − / Rx − 3 Rx + / Tx + 4 − 5 − 6 Rx − / Tx − 7 − 8 − Note! Please use prefabricated standard cables (corresponding to ISO/IEC 11801 or EN 50173) only: ƒ cable type S/FTP ƒ category CAT 5e EDK94AYCEC DE/EN/FR/ES/IT 1.
0Fig. 0Tab. 0 Equipement livré Pos. Description Module de communication E94AYCEC, ETHERNET Powerlink (CN) Instructions de montage Raccordements Pos. Description X250 Raccordement pour l’alimentation externe du module de communication Version : bornier avec fixation par vis, à 2 bornes X251 Raccordement pour ETHERNET Powerlink Version : prise RJ45 selon norme CEI 60603−7, avec LED intégrées X252 Interrupteur DIP E94YCEP001D Pos.
Affichages LED Pos. Couleur Etat Description MS Vert Clignote Le module de communication est sous tension, mais la liaison avec l’appareil de base n’est pas établie (l’appareil de base est hors tension, en cours d’initialisation ou aucun appareil de base n’est présent). On Le module de communication est sous tension et la liaison avec l’appareil de base est établie. Un défaut est survenu au niveau du module de communication.
LED Pos. Couleur Etat Description Signalisation au niveau du port X211 ou X212 : − Rouge On Collision Ethernet − Vert On Connexion Ethernet établie Clignote Liaison Ethernet établie et communication des données en cours Montage E94YCXX001G 22 EDK94AYCEC DE/EN/FR/ES/IT 1.
Démontage E94AYCXX001H EDK94AYCEC DE/EN/FR/ES/IT 1.
Validité Le présent document s’applique aux modules suivants : ƒ Modules de communication E94AYCEC, ETHERNET Powerlink (CN), à partir de la version VC 1.0 Identification Type HW Ver. SW Ver. MAC ID E94YCEI003C E94 A Y C EC VC 1.
Consignes de sécurité 1 Définition des conventions utilisées 1 Consignes de sécurité Définition des conventions utilisées Pour indiquer des risques et des informations importantes, la présente documentation utilise les mots et symboles suivants : Consignes de sécurité Présentation des consignes de sécurité Danger ! (Le pictogramme indique le type de risque.) Explication (L’explication décrit le risque et les moyens de l’éviter.
1 Consignes de sécurité Définition des conventions utilisées Consignes d’utilisation Pictogramme et mot associé Explication Remarque Remarque importante pour assurer un fonctionnement correct importante ! Conseil ! 26 Conseil utile pour faciliter la mise en oeuvre Référence à une autre documentation EDK94AYCEC DE/EN/FR/ES/IT 1.
Consignes de sécurité 1 Danger ! Tout usage contre−indiqué du module de communication et de l’appareil de base risque d’entraîner des dommages corporels et matériels graves. Tenir compte des consignes de sécurité et des dangers résiduels indiqués dans la documentation sur l’appareil de base. EDK94AYCEC DE/EN/FR/ES/IT 1.
2 2 Installation électrique Installation électrique Alimentation externe Appliquer une tension d’alimentation séparée au module de communication via le raccordement X210. Désignation Explication + Alimentation externe U = 24 V CC (20,4 V − 0 % ... 28,8 V + 0 %) I = 140 mA − Potentiel de référence pour alimentation externe En cas de distance importante entre les armoires électriques, utiliser un bloc d’alimentation pour chacune d’elles.
Installation électrique 2 Raccordement d’Ethernet E94YCEP004C Broche Signal 1 Tx + / Rx + 2 Tx − / Rx − 3 Rx + / Tx + 4 − 5 − 6 Rx − / Tx − 7 − 8 − Remarque importante ! Utiliser uniquement des câbles préfabriqués en vente dans le commerce (conformes à la norme ISO/CEI 11801 ou EN 50173) : ƒ Type de câble S/FTP ƒ Catégorie CAT 5e EDK94AYCEC DE/EN/FR/ES/IT 1.
0Fig. 0Tab. 0 Contenido del suministro Pos. Descripción Módulo de comunicación E94AYCEC, ETHERNET Powerlink (CN) Instrucciones para el montaje Conexiones Pos. Descripción X250 Conexión para la alimentación externa del módulo de comunicación Ejecución: Conector enchufable, con conexión bipolar atornillable X251 Conexión para ETHERNET Powerlink Ejecución: Conector RJ45 según IEC 60603−7, con LEDs integrados X252 Interruptor DIP E94YCEP001D Pos.
Indicadores LED Pos. Color Estado Descripción MS verde parpadea El módulo de comunicación está siendo alimentado pero no tiene comunicación con el equipo básico (el equipo básico está desconectado, está en fase de inicialización o no está disponible). encendido El módulo de comunicación está siendo alimentado y tiene comunicación con el equipo básico. Hay un error en el ámbito del módulo de comunicación.
Montaje E94YCXX001G Desmontaje E94AYCXX001H 32 EDK94AYCEC DE/EN/FR/ES/IT 1.
Validez Este manual es de aplicación para ƒ Módulos de comunicación E94AYCEC, ETHERNET Powerlink (CN), a partir de la versión VC 1.0 Identificación Type HW Ver. SW Ver. MAC ID E94YCEI003C E94 A Y C EC VC 1.
1 Instrucciones de seguridad Definición de las instrucciones utilizadas 1 Instrucciones de seguridad Definición de las instrucciones utilizadas Para indicar peligros e información importante, se utilizan en esta documentación los siguientes términos indicativos y símbolos: Instrucciones de seguridad Estructura de las instrucciones de seguridad: ¡Peligro! (indican el tipo y la gravedad del peligro) Texto indicativo (describe el peligro y da instrucciones para evitarlo) Pictograma y término indicativo
Instrucciones de seguridad 1 ¡Peligro! El uso inadecuado del módulo de comunicación y el equipo básico puede causar serios daños personales y materiales. Observe las instrucciones de seguridad y los peligros residuales que aparecen en las instrucciones del equipo básico. EDK94AYCEC DE/EN/FR/ES/IT 1.
2 2 Instalación eléctrica Instalación eléctrica Alimentación de voltaje externa Alimente el módulo de comunicación a través de la conexión X210 con voltaje de alimentación separado. Denominación Explicación + Alimentación de voltaje externa U = 24 V DC (20,4 V − 0 % ... 28,8 V + 0 %) I = 140 mA − Potencial de referencia para alimentación de voltaje externa Si hay una gran distancia entre los armarios eléctricos utilice una fuente de red en cada armario.
Instalación eléctrica 2 Conexión Ethernet E94YCEP004C PIN Señal 1 Tx + / Rx + 2 Tx − / Rx − 3 Rx + / Tx + 4 − 5 − 6 Rx − / Tx − 7 − 8 − ¡Aviso! Por favor, sólo utilice cables preconfeccionados comerciales (según ISO/IEC 11801 o resp. EN 50173): ƒ Tipo de cable S/FTP ƒ Categoría CAT 5e EDK94AYCEC DE/EN/FR/ES/IT 1.
0Fig. 0Tab. 0 Oggetto della fornitura Pos. Descrizione Modulo di comunicazione E94AYCEC, ETHERNET Powerlink (CN) Istruzioni di montaggio Collegamenti Pos. Descrizione X250 Collegamento all’alimentazione esterna del modulo di comunicazione Esecuzione: Morsettiera con collegamento a vite, a 2 poli X251 Collegamento per ETHERNET Powerlink Esecuzione: Connettore RJ45 secondo IEC 60603−7, con LED integrati X252 DIP−Switch E94YCEP001D Pos.
Indicazioni luminose LED Pos. Colore Stato Descrizione MS verde lampeggiante Il modulo di comunicazione riceve la tensione di alimentazione, ma manca il collegamento con il modulo asse (modulo asse disinserito, in fase di inizializzazione o non presente). acceso Il modulo di comunicazione riceve la tensione di alimentazione ed è correttamente collegato al modulo asse. Si è verificato un errore nel modulo di comunicazione.
Montaggio E94YCXX001G Smontaggio E94AYCXX001H 40 EDK94AYCEC DE/EN/FR/ES/IT 1.
Validità La presente documentazione è valida per ƒ Moduli di comunicazione E94AYCEC, ETHERNET Powerlink (CN), a partire dalla versione VC 1.0 Identificazione Type HW Ver. SW Ver. MAC ID E94YCEI003C E94 A Y C EC VC 1.
1 Informazioni sulla sicurezza Simbologia delle note e avvertenze utilizzate 1 Informazioni sulla sicurezza Simbologia delle note e avvertenze utilizzate Per segnalare pericoli ed informazioni importanti, nella presente documentazione sono riportati i seguenti simboli e parole di segnalazione: Note di sicurezza Struttura delle note di sicurezza: Pericolo! (indica il tipo e la gravità del pericolo) Testo della nota (descrive il pericolo e fornisce indicazioni su come può essere evitato) Simbolo e paro
Informazioni sulla sicurezza 1 Pericolo! L’utilizzo non conforme del modulo di comunicazione e del modulo asse può provocare gravi danni a persone e cose. Osservare le note sulla sicurezza e le avvertenze di pericolo contenute nelle istruzioni relative al modulo asse. EDK94AYCEC DE/EN/FR/ES/IT 1.
2 2 Installazione elettrica Installazione elettrica Alimentazione esterna Dotare il modulo di comunicazione di alimentazione esterna separata tramite il collegamento X210. Denominazione Spiegazione + Alimentazione esterna U = 24 V CC (20,4 V − 0 % ... 28,8 V + 0 %) I = 140 mA − Potenziale di riferimento per alimentazione esterna In caso di distanze elevate tra gli armadi elettrici, utilizzare un alimentatore in ogni armadio.
Installazione elettrica 2 Connessione Ethernet E94YCEP004C PIN Segnale 1 Tx + / Rx + 2 Tx − / Rx − 3 Rx + / Tx + 4 − 5 − 6 Rx − / Tx − 7 − 8 − Avvertenza: Utilizzare solo cavi preconfezionati standard (secondo ISO/IEC 11801 o EN 50173): ƒ Tipo di cavo S/FTP ƒ Categoria CAT 5e EDK94AYCEC DE/EN/FR/ES/IT 1.
Lenze Drive Systems GmbH Hans−Lenze−Straße 1 D−31855 Aerzen Germany ( ( Service Ê Service EDK94AYCEC DE/EN/FR/ES/IT 1.0 © 08/2007 TD06 +49 (0) 51 54 82−0 00 80 00 24 4 68 77 (24 h helpline) +49 (0) 51 54 82−1112 E−Mail Lenze@Lenze.de Internet www.Lenze.