L-force Controls Manual (Software) PC based Automation Global Drive Control (GDC) Industrial PC as Gateway L
This manual applies to the Lenze »Global Drive Control« (»GDC«) as of version 4.10 (SP 4) Copyright © 2008 Lenze Drive Systems GmbH. All rights reserved. Imprint Lenze Drive Systems GmbH Postfach 10 13 52, 31763 Hameln, Germany Phone: ++49 (0)5154 / 82-0 Telefax: ++49 (0)5154 / 82-2111 E-mail: Lenze@Lenze.de Copyright information All texts, photos and graphics contained in this documentation are subject to copyright protection.
Global Drive Control | Industrial PC as Gateway Inhalt Contents 1 Safety instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 2 About this Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 2.1 Conventions used . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Global Drive Control | Industrial PC as Gateway Safety instructions 2 Safety instructions Please observe the following safety instructions when you want to commission a controller or system using the »Global Drive Control«.
Global Drive Control | Industrial PC as Gateway About this Manual Conventions used 3 About this Manual This Software Manual contains information about the Industrial PC(IPC) as gateway . Note! The Software Manual supplements the Mounting Instructions enclosed with the controller, the Hardware Manual, and the Software Manual for the controller. The Mounting Instructions contain safety information which must be observed! 3.
Global Drive Control | Industrial PC as Gateway About this Manual Definition of notes used 3.
Global Drive Control | Industrial PC as Gateway IPC as gateway Setting of the communication path 4 IPC as gateway This chapter describes how to use the gateway function of an IPC to establish an online connection to a field device. The »Global Drive Control« (»GDC«) serves to access field devices like 9300, 8200 and ECS. If the field devices are driven by an IPC via the CAN fieldbus, the »GDC« is able to use the IPC as a gateway. »GDC« is interfaced to the IPC via Ethernet." 4.
Global Drive Control | Industrial PC as Gateway IPC as gateway Connect to drive r To set the communication parameters, you must enter the following information about your configuration: Information Function IP address IP address of the IPC which serves as gateway for communication CAN interface Number of the CAN interface, to which the required field device is connected CAN address Node address of the field device which you want to trigger via the gateway function of the IPC r Confirm data by OK.
Global Drive Control | Industrial PC as Gateway IPC as gateway Connect to drive r The parameters of the connected drive are read from the connected drive. 4.2.1 Remedy in case of error r If no drive can be found, the »GDC« displays an error message: F L Nur für internen Gebrauch! r Proceed as follows to remove the error: – Check the physical connections to the controller and IPC, – Make sure that the communication parameters set for the physical configuration are correct.
Global Drive Control | Industrial PC as Gateway IPC as gateway Connect to drive 4.2.2 Online mode via IPC gateway function Nur für internen Gebrauch! r After the parameters have been read in successfully, the drive is in online mode. The drive parameters are available in the »GDC«: In a separate window, the »GDC« provides an overview of the selected drives at the system bus: Note! The »GDC« displays the selected drive in the Drives connected to bus dialog window via the gateway function..
Global Drive Control | Industrial PC as Gateway Index 5 Index A Application notes 6 C Conventions used 5 Copyright 2 Copyright information 2 E E-Mail an Lenze 12 F Feedback an Lenze 12 I Imprint 2 L Layout of the safety instructions 6 Liability 2 S Safety 4 Safety instructions 6 T Trademarks 2 L 1.
)(('%$&. 12 Your opinion is important to us These Instructions were created to the best of our knowledge and belief to give you the best possible support for handling our product. If you have suggestions for improvement, please e-mail us to: feedback-docu@Lenze.de Thank you for your support.
