Show/Hide Bookmarks Ä.".$ä BA 12.0030 .ð.
Show/Hide Bookmarks Product key Gearbox type Gearbox size Step number Input design Output design Drive size C G P A Solid shaft smooth Planetary gearbox servo motor, asynchronous, externally ventilated A Servomotor, synchronous, externally ventilated S N G C ( Square flange (through holes) 1 4 l C 2 0 ) Without foot mounting with centering Expanded servomotor key M C Square measure Length of coil module . . .
Show/Hide Bookmarks GPA mounting positions A, C, D A C D Nameplate (sample) 3~MOT 330 V Hans-Lenze-Strasse 1 D-31855 Aerzen http://www.Lenze.com GPA00-1SGCN-09FN38 2.5 A # 1.6 HP $ 250 Hz ) I.CL.F IP 55 Ta 30 °C C86:1314 !! V SN 15005432100065566 UL File no. n1eck 3750 min-1 1.2 kW max. 5.9 A ( Brake Brake M2 12 Nm ! c = 2.
Show/Hide Bookmarks What is new?/ What has been changed in the Operating Instruction? Material number Edition Important Contents 00 491 027 1.0 05/04 TD09 1st edition First printing 13 011 303 2.0 08/04 TD09 1st edition Completion of the product key Completion of the chart transport weights © 2004 Lenze Drive Systems GmbH, Hans-Lenze-Straße 1, 31855 Aerzen No part of this documentation may be reproduced or made accessible to third parties without written consent by Lenze Drive Systems GmbH.
Show/Hide Bookmarks Contents 1 i Preface and general information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 1.1 About these Operating Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 1.2 Terminology used . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 1.3 Scope of supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Show/Hide Bookmarks 1 Preface and general information 1 Preface and general information 1.1 About these Operating Instructions About these Operating Instructions ƒ These Operating Instructions are intended for safety-relevant operations on and with the gearboxes G . They contain safety instructions which must be observed. ƒ All personnel working on and with the gearboxes G must have the Operating Instructions available and observe the information and notes relevant for them.
Show/Hide Bookmarks Preface and general information Lenze drive systems 1.4 1 Lenze drive systems Labelling Lenze drive systems are uniquely designated by the content of their nameplates.
Show/Hide Bookmarks 2 Safety 2 Safety 2.1 Personnel responsible for safety Personnel responsible for safety Operator ƒ An operator is any natural or legal person who uses the drive system or on behalf of whom the drive system is used. ƒ The operator or his safety officer must ensure – that all relevant regulations, instructions and legislation are observed. – that only qualified personnel work with and on the drive system.
Show/Hide Bookmarks Safety Definition of notes used 2.
Show/Hide Bookmarks 3 Technical data 3 Technical data Product features ƒ The most important technical data are indicated on the nameplate (for Design and Contents see page 3). ƒ Additional technical data are listed in the product catalogues. 3.1 Product features Design Drive systems have a modular design.
Show/Hide Bookmarks Technical data 3 Transport weights 3.
Show/Hide Bookmarks 3 Technical data 3.3 General data/operating conditions 3.3.1 Temperatures General data/operating conditions Temperatures The permissible temperature range is determined by the following: ƒ The lubricant specifications in connection with the expected oil temperatures in operation (see chapter 7.1 and nameplate). ƒ The thermal class of the motor considering the motor temperature expected during operation (see nameplate and/or Operating Instructions of the motor).
Show/Hide Bookmarks Mechanical installation 4 Storage 4 Mechanische Installation Danger! Only transport the drive with transport equipment or hoists which are suitable for this load (see transport weights, chapter 3.2). Ensure a safe fixing. Avoid shocks! The motors attached to the gearbox are partially equipped with eyebolts. These are exclusively determined for motor/gearbox mounting and dismounting and must not be used for the complete geared motor! 4.
Show/Hide Bookmarks 4 Mechanical installation 4.2.2 General information about the assembly of drive systems Mounting General information about the assembly of drive systems ƒ Take safety measures prior to any operation: – Disconnect the machine from the mains, ensure standstill of the machine and avoid any machine movement. – Check the proper state of the drive system. Never install and set up damaged drive systems. – Check the combination of drive function and machine functions.
Show/Hide Bookmarks Electrical installation 5 5 Electrical installation Danger! Electrical connections must only be made by skilled personnel! 5.1 Motor connection To correctly connect the motor options, please observe: ƒ the notes in the terminal box of the motor ƒ the notes in the Operating Instructions of the motor ƒ the technical data on the motor nameplate. BA 12.0030 EN 2.
Show/Hide Bookmarks 6 Commissioning 6 Commissioning and operation Before switching on Stop! The drive may only be commissioned by skilled personnel! 6.1 Before switching on Check: ƒ Is the mechanical fixing o.k.? ƒ Are the electrical connections o.k.? ƒ Are all rotating parts and surfaces, which may become hot, protected against contact? 6.
Show/Hide Bookmarks Maintenance 7 Maintenance intervals 7 Maintenance Gearboxes and geared motors from Lenze are filled with a drive-specific and design-specific lubricant filling at delivery. The mounting position and design are decisive at ordering for the required lubricant quantity. Note! When changing the lubricant, Lenze recommends also changing the grease packing of the bearings and replacing the radial shaft seal rings! 7.
Show/Hide Bookmarks 7 Maintenance 7.1.1 Replacing the lubricant Maintenance intervals Replacing the lubricant Stop! Gearbox should be warm. ƒ Secure drive system and machine from inadvertent movement and mains connection. ƒ 1. Drain lubricant by removing the oil drain/filler plug. 2. Fill recommended lubricant in the specified amount. 3. Insert oil drain/filler plug with new seal. 4. Dispose of waste oil according to applicable regulations. Fig.
Show/Hide Bookmarks Maintenance 7 Maintenance intervals Lubricant quantity 7.1.2 Lubricant quantity Mounting position Gearbox Tab. 2 BA 12.0030 EN 2.
Show/Hide Bookmarks 8 Troubleshooting and fault elimination 8 Troubleshooting and fault elimination If any malfunctions should occur during operation of the drive system, please check the possible causes using the following table. If the fault cannot be eliminated by one of the listed measures, please contact the Lenze Service.
Show/Hide Bookmarks Disposal 9 9 Disposal Protect the environment! Packaging material can be recycled.
Show/Hide Bookmarks 10 Appendix 10 Appendix 10.1 Manufacturer’s Certification Manufacturer’s Certification Herewith we declare that the products stated below are determined for assembly in a machine or for assembling a machine with other components. The commissioning of the machine is prohibited as long as it has been ascertained that it meets the EC Directive 98/37/EC. Lenze Drive Systems GmbH P.O.
Show/Hide Bookmarks N Lenze Drive Systems GmbH Hans-Lenze-Straße 1 31855 Aerzen Germany Service ¬ Service +49 (0) 51 54 82-0 00 80 00 24 4 68 77 (24 h helpline) +49 (0) 51 54 82-1112 E-Mail Internet Lenze@Lenze.de www.Lenze.com BA 12.0030 2.
