Submittal Sheet

Submittal Data Sheet S-1232R-LF
August, 2018
1360 Elmwood Avenue, Cranston, RI 02910 USA
Phone: [phone] Fax: [phone]
Email: [e-mail]
Web Site: http://www.leonardvalve.com
Engineer's Approval Job # ____________________
Arch/Eng. ________________
Contractor ________________
TM-2020B-LF-DT_______
 Large Type TM Thermostatic water mixing valve, adjustable high
temperature limit stop*, inlet checkstops, wall support, outlet ball
valve
 Small Type TM Thermostatic water mixing valve, adjustable high
temperature limit stop*, integral checkstops, outlet ball valve
 2" inlets, 2" outlet (51mm X 51mm)
 Maximum operating pressure: 125 PSI (860 KPA)
 1 GPM (3.7 l/min) minimum flow capacity
 Color-coded dial thermometer (0 to 140F, -10 to 60C)
 Inlet manifold piping
 Locking temperature regulator
 Factory assembled and tested
This product is certified to meet Low Lead requirements of wetted
surface area containing less than 0.25% lead by weight. All other
component accessories, the sum total of which comprise the wetted
surface area of this product, contain less than one quarter of one
percent lead by weight.
OPTIONS:
____SUFFIX CP – Chrome plated (Material finish may vary)
____SUFFIX IT – Inlet Thermometers (shipped loose)
____SUFFIXTC–Test connection (shipped loose)
____SUFFIX HT – High temperature thermometer
(0 to 250F, -18 to 121C)
*NOTE: A limit stop, set for 120F(49C), is simply a mechanical setting
to prevent excessive handle rotation. If incoming water is hotter than 150F
(65.5C), the temperature of the factory test, the valve when turned to full
HOT may deliver water in excess of 120F and the limit stop MUST BE
RESET BY THE INSTALLER
CAUTION! All thermostatic water mixing valves have limitations.
They will NOT provide the desired accuracy outside of their flow
capacity range. Consult the Flow Capacity Chart and DO NOT
OVERSIZE. Minimum flow must be no less than as indicated.
A=12” +/- ½” B=31” C=2 ¾”
PRESSURE DROP
MINIMUM
(l/min)
(GPM)
FLOW
1.0
(3.7)
549488295 428
10
113
.7
78
.3
5
129 145
15
.97 1.4
20
746
651 712617
163 172
1.7
25
2.1
30
188
197
2.4
35 40
2.8
l/min
810 856
214 226
3.1
45
3.4
50
GPM
PSI
BAR
NEXT GENERATION
HIGH LOW
SYSTEM
NOTE: Flow rates will vary depending on existing field conditions.
Leonard Valve Company always recommends using CASPAK® sizing
software for proper valve sizing and model number applications.
Note: The models shown represent Leonard Products which are believed to be
equivalent in type and function to items specified. Leonard Valve Company is
not responsible for errors or omissions due to differences in interpretations of
information provided.
ECO-MIX
™
Note: Leonard Valve Company reserves the right of product, or
design modifications without notice or obligation.
LEONARD
THERMOST ATIC
C
H
ASSE
1017
A
1
4
0
0
1
0
0
1
2
0
10
4
0
LEONARD
-10
2
0
0
50
°C
°F
60
R
40
20
6
0
8
0
30
B
C
Valve assembly is ASSE 1017 Certified
Valve assembly is CSA Certified
DT ASSEMBLY
IS A COMPONET ACCESORY
INCLUDED BY FACTORY
+NOTE: The valve will maintain temperature with 0.5GPM flow
from the domestic hot water loop when properly installed near the
hot water source with a continuously operating recirculation pump.
WARNING: This product can expose you to
chemicals including lead, which is known to the
State of California to cause cancer. For more
information, go to www.P65Warnings.Ca.gov
!