C TUB DOORS • SHOWER DOORS INSTALLATION INSTRUCTIONS TUB DOORS: SHOWER DOORS: LBTDC6062 LBSDC4876 LBSDC6076 www.lesscare.com Version 5.
TUB DOORS • SHOWER DOORS ULTRA-C PREPARATION FOR INSTALLATION PREPARATION FOR INSTALLATION READ ALL INSTRUCTIONS BEFORE UNPACKING THE PRODUCT 2 PEOPLE ARE REQUIRED TO LIFT AND DURING ENTIRE INSTALLATION OF THIS PRODUCT LessCare reserves the right to change, update, modify, alter, redesign this manual/product or its policies without prior notice! It is your responsibility to visit website to download or contact customer service for the most updated version of the installation instructions.
TUB DOORS • SHOWER DOORS ULTRA-C CONFIGURATION STYLES MODELS: LBTDC6062 Threshold Requirement (Size): 2 3/4" Min. Threshold Requirement SAFETY IMPORTANT NOTE: Installation of shower or bathtub door requires to be installed only on smooth and flat surface of both walls and threshold base (shower base or bathtub). www.lesscare.
TUB DOORS • SHOWER DOORS ULTRA-C CONFIGURATION STYLES MODELS: LBSDC4876 LBSDC6076 Threshold Requirement (Size): 2 3/4" Min. Threshold Requirement SAFETY IMPORTANT NOTE: Installation of shower or bathtub door requires to be installed only on smooth and flat surface of both walls and threshold base (shower base or bathtub). 3 www.lesscare.
TUB DOORS • SHOWER DOORS ULTRA-C SHOWER DOOR COMPONETS 19 18 17 1 2 3 4 16 5 6 7 8 9 10 11 12 13 Item# Description 1 2 3 4 5 6 7 8 9 10 11 15 14 Qty Bumper Strip Guide Rail Bracket Glass Door Stopper Upper Guide Rail Roller Handle Glass Door Side Anti-Water Strip Anti-splash Threshold Screw M4X45 Threshold Cover 1 pc 2 pcs 2 pcs 1 pc 2 pcs 1 pc 1 pc 1 pc 1 pc 2 pcs 1 pc Item# Description 12 13 14 15 16 17 18 19 20 21 22 Screw M5X30 Guide Block Wall Anchor Bottom Mount Clamp Stationary Glass
TUB DOORS • SHOWER DOORS ULTRA-C INSTALLATION STEPS 1. Measure the distance between two finished walls. This distance is marked as W. a Please see Fig 1 for details 90° Figure 1 5 www.lesscare.
TUB DOORS • SHOWER DOORS ULTRA-C INSTALLATION STEPS a. 18 4 18 b. c. 2. Your Upper Guide Rail (4) has been precut for your Shower model opening width: 48" or 60" for shower width. If W-width of your wall-to-wall opening is equal to the size of your Shower model, it is unnecessary to cut the Upper Guide Rail and you can continue to Step 3.
TUB DOORS • SHOWER DOORS ULTRA-C INSTALLATION STEPS 3. Install Bottom Mount Clamp 3.1 Loosen the screw on the Bottom Mount Clamp (15) with Allen Key. Disassemble the Bottom Mount Clamp (15) and install the clamp on the notch of the Stationary Glass (16). IMPORTANT: Make sure that clear rubber gaskets and washer are in between the glass and clamp's plates. Make sure that the clamp with screw is facing inside the shower. Please see Fig 3 for details a. 15 16 b. c. 15 15 7 Figure 3 www.lesscare.
TUB DOORS • SHOWER DOORS ULTRA-C INSTALLATION STEPS a. b. 2 2 c. 3 4 d. 18 e. f. 2 3 18 g. Figure 4 5 1/8" 3 9/16" 2 18 4 2 4. Upper Guide Rail Installation 4.1 Use the Allen Keys (20) to loosen the screws on the Guide Rail Brackets (2) and the Glass Door Stoppers (3). Slide the parts onto the Upper Guide Rail (4). Note: On the other side, the stopper must be installed in between the Glass Bracket (18).
TUB DOORS • SHOWER DOORS ULTRA-C INSTALLATION STEPS a. b. 18 18 c. 5. Loosen the screw on the Glass Bracket (18) with Allen Key (20), align the holes of the Brackets(18) to the holes on the Stationary Glass (16), secure the Upper Guide Rail (4) with the Stationary Glass together by tightening the screws on the Glass Bracket with Allen Key. 18 Please see Fig 5 for details. 18 Figure 5 9 ATTENTION: Never set your glass down directly onto a tile or concrete floor.
TUB DOORS • SHOWER DOORS ULTRA-C INSTALLATION STEPS a. b. c. 2 d. 16 Inside 16 Inside Figure 6 6.Install Stationary Glass Place the Stationary Glass Assembly to the wall. Make sure the Stationary Glass (16) and the Upper Guide Rail (4) are leveled. Please see Fig 6 for details. www.lesscare.
TUB DOORS • SHOWER DOORS ULTRA-C INSTALLATION STEPS a. 2 b. 16 Inside Inside c. d. 2 15 Inside e. f. Inside Inside g. h. i. j. 15 Outside Outside Figure 7 7. Slide the Guide Rail Bracket (2) against the wall, outline the Guide Rail Brackets (2) position on the wall with a pencil. Outline the position of the Bottom Mount Clamp (15) on the shower tray or threshold. Set the Stationary glass assembly aside.
TUB DOORS • SHOWER DOORS ULTRA-C INSTALLATION STEPS 8. Drill the holes on the wall using 8mm(5/16") drill bit and apply silicone into the holes, insert the Wall Anchors (14). Drill the holes on the shower tray or threshold with 8mm(5/16") drill bit and apply silicone into the holes, insert the Wall Anchors (14). Mount the Wall Bracket of the Guide Rail Bracket (2) to the wall using the Screw M5×60 (17).
TUB DOORS • SHOWER DOORS ULTRA-C INSTALLATION STEPS 9. Place the Stationary Glass Assembly back to the designated position. Install the Bottom Mount Clamp (15) back to the Stationary Glass (16).Slide the Guide Rail Bracket (2) to the two end sides of the Upper Guide Rail(4). Fasten the female part of the Guide Rail Bracket to the wall bracket on the wall. Tighten the set screws on the Guide rail brackets with Allen Key (20) to secure the Upper Guide Rail to the two walls. Please see Fig 9 for details a.
TUB DOORS • SHOWER DOORS ULTRA-C INSTALLATION STEPS a. 20 Attention: Need to loosen the small allen screws before loosening the long allen screw on the roller 5 b. 6 IMPORTANT: When installing the rollers and handle to the glass door, make sure that clear rubber gaskets are in between the Glass Door (7) and the related hardwares. Tighten the knob and cap on the handle by hand only. Do not use any types of tools to tighten it.
TUB DOORS • SHOWER DOORS ULTRA-C INSTALLATION STEPS a. 5 7 7 5 5 b. 7 6 5 c. 7 6 Figure 10 d. 1 10. Loosen the Rollers (5) screw and Install the Rollers to the Glass Door (7). And then Install Handle (6) to the Glass Door . At last Install the Bumper Strip(1) to the Glass Door(7). Please see Fig 10 for details 15 www.lesscare.
TUB DOORS • SHOWER DOORS ULTRA-C INSTALLATION STEPS a. b. 16 13 inside 13 13 d. c. e. inside inside inside f. h. g. inside inside inside Silicone 14 12 Figure 11 11. The slot direction for the Stationary Glass (16) of the Guide Block (13) can be adjusted. Loosen the screw on the bottom of the Guide Block and adjust the direction. Put the Guide Block to the Stationary Glass, make sure that the glass is inside the slot of the Guide Block.
TUB DOORS • SHOWER DOORS ULTRA-C INSTALLATION STEPS a. 7 b. inside Figure 12 12. Hang the Glass Door Assembly to the Upper Guide Rail (4), put the bottom edge of the glass door to the slot of the Guide Block (13). Make sure that the glass door will not touch the metal part of the Guide block. 7 13 See Figure 12 for details. 13. Slide the Side Anti-Aater Atrip (8) to the Stationary Glass (16), remove the flapper that interfere with the Upper Guide Rail (4) with scissors.
TUB DOORS • SHOWER DOORSURES ULTRA-C INSTALLATION STEPS a. b. 19 Outside 14. Install the Safety Pin(11) to the Glass Door (7). Please see Fig 14 for details IMPORTANT: When installing the safety pins to the glass door, make sure that clear rubber gaskets are in between the Glass Door (7) and the related hardwares and the washer are inside the holes of the glass door. Figure 14 www.lesscare.
TUB DOORS • SHOWER DOORS ULTRA-C INSTALLATION STEPS a. 3 b. Inside c. d. 2 19 e. 2 19 Figure 15 15. Adjust the Roller(5) and locate the Glass Door Stopper(3) 15.1. Adjust the fasteners on both Rollers (5) to ensure that the bottom edge of the Glass Door (7) will not touch the bottom of the Guide Block (13). NOTE: Glass Door can be adjusted up or down for 2mm by adjusting the fasteners on the Rollers. 15.2.
TUB DOORS • SHOWER DOORS ULTRA-C INSTALLATION STEPS IMPORTANT STEP! 16. Measure and Trim the Anti-Splash Threshold Measure the dimension of the threshold opening by attaching the threshold cover to the threshold and place the threshold into the threshold opening. If the threshold is too long to fit into the guide block mark a cut line on the threshold and trim the threshold using a meter saw. Please see Fig 16 Outside Trim th e thres to your hold in accor da door op ening nce Figure 16 www.lesscare.
TUB DOORS • SHOWER DOORS ULTRA-C INSTALLATION STEPS IMPORTANT STEP! 17. Cut the Anti-splash Threshold if it is necessary Please see Fig 17 9 9 9 Figure 17 21 www.lesscare.
TUB DOORS • SHOWER DOORS ULTRA-C INSTALLATION STEPS 18. Install the Anti-Splash Threshold Pull out the Cover in the guide block (13), put the Anti-Splash Threshold (9) to the slot of the Guide Block, in front of the Glass Door (7) on the shower tray or threshold. Put the Threshold Cover (11) to the end of the Threshold against the wall. Mark a drill hole on a threshold with a pencil. Drill the hole on a threshold with drill bit 8mm (5/16"). Attach the threshold and mark a drill hole on a shower base.
TUB DOORS • SHOWER DOORS ULTRA-C INSTALLATION STEPS g. h. 14 Silicone Outside Outside i. j. Silicone Outside k. 10 Outside Screw M4X45 Figure 18 23 www.lesscare.
TUB DOORS • SHOWER DOORS ULTRA-C EXTREMELY IMPORTANT INSTALLATION & TECHNICAL MAINTENANCE INSTRUCTIONS EXTREMELY IMPORTANT! The instructions specified and described on this page are extremely important and are required during installation and regular technical maintenance of the product.
TUB DOORS • SHOWER DOORS ULTRA-C EXTREMELY IMPORTANT INSTALLATION & TECHNICAL MAINTENANCE INSTRUCTIONS EXTREMELY IMPORTANT INSTALLATION & TECHNICAL MAINTANCE INSTRUCTIONS! A licensed and professional contractor has to comply with the required specifications and dimensions illustrated on this diagram during installation and technical maintenance of the product. 1.
TUB DOORS • SHOWER DOORS ULTRA-C INSTALLATION STEPS Silicone Silicone Silicone Silicone 17. Apply silicone sealant on the seams between the stationary glass and the shower tray/threshold, and between the wall and the stationary glass. See Figure 17 for details. WAIT 24 HOURS BEFORE USING THE SHOWER ENCLOSURE TUB DOORS INSTALLATION the same as SHOWER DOORS Silicone Silicone Silicone Silicone IMPORTANT: MUST ALOW SILICONE TO DRY FOR 24 HOURS BEFORE STARTING USING THE SHOWER ENCLOSURE www.lesscare.
TUB DOORS •SHOWER DOORS ULTRA-C MAINTENANCE, USE, AND CARE Maintenance & Care IMPORTANT! DO NOT USE: Abrasive cleaners such as: acid, ammonia, bleach, and simmilar solutions; or any types of baking soda cleaning solutions.Use of such solutions may cause corrosion, finish peeling, and/or dull the surface. DO NOT USE: Abrasive sponges or cloth. Never use steel, wool, or wired brushes that will permanently scratch the surface.
C SHOWER DOORS INSTALLATION INSTRUCTIONS SHOWER DOORS: LBSDC7276 www.lesscare.com Version 5.
SHOWER DOORS ULTRA-C PREPARATION FOR INSTALLATION PREPARATION FOR INSTALLATION READ ALL INSTRUCTIONS BEFORE UNPACKING THE PRODUCT 2 PEOPLE ARE REQUIRED TO LIFT AND DURING ENTIRE INSTALLATION OF THIS PRODUCT LessCare reserves the right to change, update, modify, alter, redesign this manual/product or its policies without prior notice! It is your responsibility to visit website to download or contact customer service for the most updated version of the installation instructions.
SHOWER DOORS ULTRA-C CONFIGURATION STYLES MODELS: LBSDC7276 3 Threshold Requirement (Size): 2 3/4" Min. Threshold Requirement SAFETY IMPORTANT NOTE: Installation of shower or bathtub door requires to be installed only on smooth and flat surface of both walls and threshold base (shower base or bathtub). www.lesscare.
SHOWER DOORS ULTRA-C SHOWER DOOR COMPONETS 18 17 16 1 2 3 15 4 5 6 7 8 9 19 10 11 12 14 13 Item# Description 1 2 3 4 5 6 7 8 9 10 11 Qty Guide Rail Bracket Glass Door Stopper Upper Guide Rail Roller Handle Glass Door Side Anti-Water Strip Anti-splash Threshold Screw M4X45 Threshold Cover Screw M5X30 2 pcs 2 pcs 1 pc 2 pcs 1 pc 1 pc 2 pcs 1 pc 2 pcs 1 pc 2 pcs Item# Description 12 13 14 15 16 17 18 19 20 21 22 Guide Block Wall Anchor Bottom Mount Clamp Stationary Glass Screw M5X60 Glass Bracket
SHOWER DOORS ULTRA-C SHOWER DOOR COMPONETS 20 22 21 23 24 25 Item# Description 20 21 22 23 24 25 Qty Glass Bracket for Small Stationary Glass Small Stationary Glass Side Anti-Water Strip Screw M4X45 Bottom Mount Clamp Wall Anchor www.lesscare.
SHOWER DOORS ULTRA-C INSTALLATION STEPS 1. Measure the distance between two finished walls. This distance is marked as W. a Please see Fig 1 for details 90° Figure 1 5 www.lesscare.
SHOWER DOORS ULTRA-C INSTALLATION STEPS a. 17 1 3 1 Note: The Glass Bracket(17) has been pre-installed to the Upper Guide Rail(3). b. c. 2. Your Upper Guide Rail (3) has been precut for your Shower model opening width 72" for shower width. If W-width of your wall-to-wall opening is equal to the size of your Shower model, it is unnecessary to cut the Upper Guide Rail and you can continue to Step 3.
SHOWER DOORS ULTRA-C INSTALLATION STEPS 3. Install Bottom Mount Clamp 3.1 Loosen the screw on the Bottom Mount Clamp (14) with Allen Key. Disassemble the Bottom Mount Clamp (14) and install the clamp on the notch of the Stationary Glass (15). IMPORTANT: Make sure that clear rubber gaskets and washer are in between the glass and clamp's plates. Make sure that the clamp with screw is facing inside the shower. Please see Fig 3 for details a. 14 15 b. c. 14 7 Figure 3 www.lesscare.
SHOWER DOORS ULTRA-C INSTALLATION STEPS a. b. 1 1 c. 2 3 d. 17 e. f. 1 2 17 g. Figure 4 5 1/8" 15 9/16" 1 17 3 1 4. Upper Guide Rail Installation 4.1 Use the Allen Keys (19) to loosen the screws on the Guide Rail Brackets (1) and the Glass Door Stoppers (2). Slide the parts onto the Upper Guide Rail (3). Note: On the other side, the stopper must be installed in between the Glass Bracket (17).
SHOWER DOORS ULTRA-C INSTALLATION STEPS a. b. 17 17 Outside c. 5. Loosen the screw on the Glass Bracket (17) with Allen Key (19), align the holes of the Brackets to the holes on the Stationary Glass (15), secure the Upper Guide Rail (3) with the Stationary Glass together by tightening the screws on the Glass Bracket with Allen Key. 17 17 Figure 5 9 Please see Fig 5 for details. Outside ATTENTION: Never set your glass down directly onto a tile or concrete floor.
SHOWER DOORS ULTRA-C INSTALLATION STEPS a. b. Outside Outside 1 c. d. 15 15 Inside Inside Figure 6 6. Install Stationary Glass Place the Stationary Glass Assembly to the wall. Make sure the Stationary Glass (15) and the Upper Guide Rail (3) are leveled. Please see Fig 6 for details. www.lesscare.
SHOWER DOORS ULTRA-C INSTALLATION STEPS a. 1 15 b. Inside c. 15 Inside Inside e. d. 1 f. Inside Inside g. h. i. j. Outside 14 Outside Figure 7 7. Slide the Guide Rail Bracket (1) against the wall, outline the Guide Rail Brackets position on the wall with a pencil. Outline the position of the Bottom Mount Clamp (14) on the shower tray or threshold. Set the Stationary glass assembly aside.
SHOWER DOORS ULTRA-C INSTALLATION STEPS 8. Drill the holes on the wall using 8mm(5/16") drill bit and apply silicone into the holes, insert the Wall Anchors (13). Drill the holes on the shower tray or threshold 8mm(5/16") drill bit and apply silicone into the holes, insert the Wall Anchors (13). Mount the Wall Bracket of the Guide Rail Bracket (1) to the wall using the Screw M5×60 (16).Mount the male parts of the Bottom Mount Clamp(14) onto the shower tray or threshold using the Screw M4X45(9).
SHOWER DOORS ULTRA-C INSTALLATION STEPS 9. Place the Stationary Glass Assembly back to the designated position. Install the Bottom Mount Clamp (14) back to the Stationary Glass (15). Slide the Guide Rail Bracket (1) to the two end sides of the Upper Guide Rail(3). Fasten the female part of the Guide Rail Bracket to the wall bracket on the wall. Tighten the set screws on the Guide rail brackets with Allen Key (19) to secure the Upper Guide Rail to the two walls. Please see Fig 9 for details a. b.
SHOWER DOORS ULTRA-C INSTALLATION STEPS 10. Install small stationary glass 10.1 Loosen the screw on Bottom Mount Clamp (24). Disassemble the Clamp and install the wall clamp on the Small Stationary Glass (21). Please see Fig 10 for details a. 24 b. Outside c. 21 Outside 24 Figure 10 www.lesscare.
SHOWER DOORS ULTRA-C INSTALLATION STEPS b. a. 3 20 20 c. 11. Install the Glass Bracket (20) for the Small Stationary Glass to the Upper Guide Rail (3), install the Small Stationary Glass (21) to the guide rail. 20 Please see Fig 11 for details Outside 21 Outside Figure 11 15 www.lesscare.
SHOWER DOORS ULTRA-C INSTALLATION STEPS a. b. 15 13 Inside c. d. Outside Outside Figure 12 12. Outline the position of the Bottom Mount Clamp (24) on the shower base and threshold. Set the Small Stationary Glass Assembly aside. Remove the clamp from the Small Stationary Glass and place it back to the outlined position. Now mark the drilling holes on the shower tray or threshold. Please see Fig 12 for details. www.lesscare.
SHOWER DOORS ULTRA-C INSTALLATION STEPS a. b. Silicone Outside Outside c. d. Outside Outside f. e. Outside Outside 13. Drill the holes on the shower tray or threshold with 8mm(5/16") drill bit and apply silicone into the holes, insert the Wall Anchors (25). Mount the male parts of the Clamp(24) onto the shower tray or threshold using the Screw M4X45(23).
SHOWER DOORS ULTRA-C INSTALLATION STEPS a. 19 Attention: Need to loosen the small allen screws before loosening the long allen screw on the roller 4 b. 5 IMPORTANT: When installing the rollers and handle to the glass door, make sure that clear rubber gaskets are in between the Glass Door (6) and the related hardwares. Tighten the knob and cap on the handle by hand only. Do not use any types of tools to tighten it. Tighten the screws on the roller with related size of Allen Keys (19) only. www.
SHOWER DOORS ULTRA-C INSTALLATION STEPS a. 4 6 4 6 4 b. 6 4 c. 6 Figure 14 5 19 14. Lossen the Rollers (04) screw and the Install Rollers to the Glass Door(6). And then Install Handle (5) to the Glass Door. Please see Fig 14 for details www.lesscare.
SHOWER DOORS ULTRA-C INSTALLATION STEPS a. b. 15 12 12 Inside 12 d. c. Inside Inside f. e. Inside h. g. Inside Silicone Inside 13 11 Figure 15 15. The slot direction for the Stationary Glass (15) of the Guide Block (12) can be adjusted. Loosen the screw on the bottom of the Guide Block and adjust the direction. Put the Guide Block to the Stationary Glass, make sure that the glass is inside the slot of the Guide Block. Now mark down the predrilled hole of the Guide Block with pencil.
SHOWER DOORS ULTRA-C INSTALLATION STEPS 16. Hang the Glass Door Assembly to the Upper Guide Rail (3), put the bottom edge of the glass door to the slot of the Guide Block (12). Make sure that the Glass Door (6) will not touch the metal part of the Guide block. See Figure 16 for details. Figure 16 a. b. 12 Inside Outside 21 www.lesscare.
SHOWER DOORS ULTRA-C INSTALLATION STEPS a. b. Outside Outside d. c. Outside Outside 12 22 Side Anti-Aater Atrip 7 Side Anti-Aater Atrip Figure 17 17. Slide the Side Anti-Aater Atrip (7) & (22) to the Stationary Glass (15) & (21), remove the flapper that interfere with the Upper Guide Rail (3) with scissors. See Figure 17 for details. www.lesscare.
SHOWER DOORS ULTRA-C INSTALLATION STEPS a. b. 18 Outside c. Outside Figure 18 18. Install the Safety Pin(18) to the Glass Door (6). Please see Fig 18 for details IMPORTANT: When installing the safety pins to the glass door, make sure that clear rubber gaskets are in between the Glass Door (6) and the related hardwares and the washer are inside the holes of the glass door. 23 www.lesscare.
SHOWER DOORS ULTRA-C INSTALLATION STEPS a. b. 2 Outside Inside c. Outside d.4 e. 4 18 18 Figure 19 19. Adjust the Roller(4) and locate the Glass Door Stopper(2) 19.1. Adjust the fasteners on both Rollers (4) to ensure that the bottom edge of the Glass Door (6) will not touch the bottom of the Guide Block (12). NOTE: Glass Door can be adjusted up or down for 2mm by adjusting the fasteners on the Rollers. 19.2.
SHOWER DOORS ULTRA-C INSTALLATION STEPS IMPORTANT STEP! 20. Measure and Trim the Anti-Splash Threshold Measure the dimension of the threshold opening by attaching the threshold cover to the threshold and place the threshold into the threshold opening. If the threshold is too long to fit into the guide block mark a cut line on the threshold and trim the threshold using a meter saw. Please see Fig 16 Trim the th r to yo eshold in ur do a or op ccordanc ening e Outside Figure 20 25 www.lesscare.
SHOWER DOORS ULTRA-C INSTALLATION STEPS IMPORTANT STEP! 21. Cut the Anti-splash Threshold if it is necessary Please see Fig 21 9 9 9 Figure 21 www.lesscare.
SHOWER DOORS ULTRA-C INSTALLATION STEPS 22. Install the Anti-Splash Threshold Pull out the Cover in the guide block (12), put the Anti-Splash Threshold (8) to the slot of the Guide Block, in front of the Glass Door (6) on the shower tray or threshold. Put the Threshold Cover (11) to the end of the Threshold against the Small Stationary Glass (21). Mark a drill hole on the shower base with a pencil. Drill the hole in the shower base with drill bit 8mm (5/16").
SHOWER DOORS ULTRA-C INSTALLATION STEPS f. e. 16 Silicone Outside Outside g. h. Silicone Silicone 9 13 Outside i. 9 Outside Figure 22 www.lesscare.
SHOWER DOORS ULTRA-C EXTREMELY IMPORTANT INSTALLATION & TECHNICAL MAINTENANCE INSTRUCTIONS EXTREMELY IMPORTANT! The instructions specified and described on this page are extremely important and are required during installation and regular technical maintenance of the product.
SHOWER DOORS ULTRA-C EXTREMELY IMPORTANT INSTALLATION & TECHNICAL MAINTENANCE INSTRUCTIONS EXTREMELY IMPORTANT INSTALLATION & TECHNICAL MAINTANCE INSTRUCTIONS! A licensed and professional contractor has to comply with the required specifications and dimensions illustrated on this diagram during installation and technical maintenance of the product. 1.
SHOWER DOORS ULTRA-C INSTALLATION STEPS Silicone Silicone Silicone Silicone Figure 23 IMPORTANT: MUST ALOW SILICONE TO DRY FOR 24 HOURS BEFORE STARTING USING THE SHOWER ENCLOSURE Silicone Silicone Silicone Silicone 23. Apply silicone sealant on the seams between the stationary glass and the shower tray/threshold, and between the wall and the stationary glass. See Figure 23 for details. WAIT 24 HOURS BEFORE USING THE SHOWER ENCLOSURE 31 www.lesscare.
SHOWER DOORS ULTRA-C MAINTENANCE, USE, AND CARE Maintenance & Care IMPORTANT! DO NOT USE: Abrasive cleaners such as: acid, ammonia, bleach, and simmilar solutions; or any types of baking soda cleaning solutions. Use of such solutions may cause corrosion, finish peeling, and/or dull the surface. DO NOT USE: Abrasive sponges or cloth. Never use steel, wool, or wired brushes that will permanently scratch the surface.
C SHOWER ENCLOSURES INSTALLATION INSTRUCTIONS SHOWER ENCLOSURES: LBSDC4876 + LBSEC34576 LBSDC4876 + LBSEC3676 LBSDC6076 + LBSEC34576 LBSDC6076 + LBSEC3676 LBSDC7276 + LBSEC34576 LBSDC7276 + LBSEC3676 www.lesscare.com Version 5.
SHOWER ENCLOSURES ULTRA-C PREPARATION FOR INSTALLATION PREPARATION FOR INSTALLATION READ ALL INSTRUCTIONS BEFORE UNPACKING THE PRODUCT 2 PEOPLE ARE REQUIRED TO LIFT AND DURING ENTIRE INSTALLATION OF THIS PRODUCT LessCare reserves the right to change, update, modify, alter, redesign this manual/product or its policies without prior notice! It is your responsibility to visit website to download or contact customer service for the most updated version of the installation instructions.
SHOWER ENCLOSURES ULTRA-C CONFIGURATION STYLES MODELS: LBSDC7276 Threshold Requirement (Size): 2 3/4" www.lesscare.
SHOWER ENCLOSURES ULTRA-C CONFIGURATION STYLES Threshold Requirement (Size): 2 3/4" 3 www.lesscare.
SHOWER ENCLOSURES ULTRA-C SHOWER DOOR COMPONENTS 19 18 17 1 2 3 4 16 5 6 7 8 9 10 11 12 13 14 Item# Description 1 2 3 4 5 6 7 8 9 10 11 Qty Bumper Strip Guide Rail Bracket Glass Door Stopper Upper Guide Rail Roller Handle Glass Door Side Anti-Water Strip Anti-splash Threshold Screw M4X45 Threshold Cover 20 15 1 pc 2 pcs 2 pcs 1 pc 2 pcs 1 pc 1 pc 1 pc 1 pc 2 pcs 1 pc Item# Description 12 13 14 15 16 17 18 19 20 21 22 Screw M5X30 Guide Block Wall Anchor Bottom Mount Clamp Stationary Glass Scr
SHOWER ENCLOSURES ULTRA-C SMALL STATIONARY GLASS COMPONENTS 21 23 22 24 25 26 Item# Description 21 22 23 24 25 26 5 Qty Glass Bracket for Small Stationary Glass Small Stationary Glass Side Anti-Water Strip Screw M4X45 Wall Mount Clamp Wall Anchor www.lesscare.
SHOWER ENCLOSURES ULTRA-C RETURN PANEL COMPONENTS 29 27 28 30 31 32 Item# Description 27 28 29 30 31 32 Qty Glass connector Return Panel Glass Mount Clamp Wall Anchor Screw M4X60 Screw M4X45 www.lesscare.
SHOWER ENCLOSURES ULTRA-C INSTALLATION STEPS a. Assembly and Installation 1. Measure the distance between two finished walls. This distance is marked as W. Please see Fig 1 for details Figure 1 7 www.lesscare.
SHOWER ENCLOSURES ULTRA-C INSTALLATION STEPS a. 27 2 18 4 Note: The Glass Bracket (18) has been pre-installed to the Upper Guide Rail (4). b. c. 27 18 4 2 Attention: Please cut the guide rail from this side, which is farther side from the hole of the guide rail bracket. 2. Your Upper Guide Rail (4) has been precut for your Shower model opening width: 48" or 60" for shower width.
SHOWER ENCLOSURES ULTRA-C INSTALLATION STEPS 3. Install Return Panel 3.1 Loosen the screw on the Clamp (29) with Allen Key. Disassemble the Clamp and install the clamp on the notch of the Return Panel Glass (28). IMPORTANT: Make sure that clear rubber gaskets and washer are in between the glass and clamp's plates. Make sure that the clamp with screw is facing inside the shower. Please see Fig 3 for details a. 29 29 b. c. 28 d. 29 29 Figure 3 9 www.lesscare.
SHOWER ENCLOSURES ULTRA-C INSTALLATION STEPS b. a. 28 29 Inside c. d. 29 29 Inside Inside Figure 4 Inside 3.2 Put the Return Panel Assembly against the wall, level it. Outline the position of the Clamp (29) on the wall and the shower base or threshold separately. Please see Fig 4 for details 29 a. 29 b. Outside d. c. 29A Outside 29A Figure 5 Outside 3.
SHOWER ENCLOSURES ULTRA-C INSTALLATION STEPS 3.4 Drill the holes in the wall using Ø8mm(Ø5/16") drill bit and Apply silicone into the holes on the wall, insert the Wall anchors (30) for the Clamps (29). Mount the Clamps to the wall using the Philip's screw M4*60(31). Drill the hole in the shower base or threshold using Ø3mm (1/8”) drill bit and mount the Clamp (29) to the shower base or threshold using the Philip's screw M4*30(32). See Fig 6 for details a. c. b. d.
SHOWER ENCLOSURES ULTRA-C INSTALLATION STEPS 4. Loosen the screw on the Bottom Mount Clamp (15) with Allen Key. Disassemble the Bottom Mount Clamp (15) and install the clamp on the notch of the Stationary Glass (16). IMPORTANT: Make sure that clear rubber gaskets and washer are in between the glass and clamp's plates. Make sure that the clamp with screw is facing inside the shower. Please see Fig 8 for details a. 15 b. Outside c. Outside 15 15 Figure 8 www.lesscare.
SHOWER ENCLOSURES ULTRA-C INSTALLATION STEPS a. b. 28 2 27A c. d. 27A 3 4 4 3 27A f. e. 3 18 2 18 g. h. 27A 4 Figure 9 18 2 5. Roller Bar Installation 5.1 Use the Allen Keys (20) to loosen the screws on the Guide Rail Brackets (2) and the Glass Door Stoppers (3). Slide the parts onto the Upper Guide Rail (4). Note: On the other side, the stopper must be installed in between the Glass Bracket (18).
SHOWER ENCLOSURES ULTRA-C INSTALLATION STEPS a. b. 18 18 Outside c. Outside 5.2 Loosen the screw on the Guide Rail Bracket (2) with Allen Key (20), align the holes of the Brackets(18) to the holes on the Stationary Glass (16), secure the Upper Guide Rail (4) with the Stationary Glass together by tightening the screws on the Guide Rail Bracket with Allen Key(20). 18 18 Please see Fig 10 for details. Outside ATTENTION: Never set your glass down directly onto a tile or concrete floor.
SHOWER ENCLOSURES ULTRA-C INSTALLATION STEPS 16 28 Outside a. b. 28 Outside Outside Figure 11 6. Place the Stationary Glass Assembly on the preinstalled shower base or threshold and butt it up against the wall. Temporarily fasten the Upper Guide Rail (4) to the Return Panel Glass(28) with the Glass Connector (27). Slightly tighten the set screws. Make sure the Stationary Glass (16) and the Upper Guide Rail (4) are leveled.
SHOWER ENCLOSURES ULTRA-C INSTALLATION STEPS d. c. Outside 2 16 2 16 Inside e. f. 2 2A Inside g. h. 15 15 Inside i. j. Outside Figure 12 www.lesscare.
SHOWER ENCLOSURES ULTRA-C INSTALLATION STEPS 7. Drill the hole on the wall using 8mm(5/16") drill bit and apply silicone into the holes, insert the Wall Anchor (14). Drill the hole on the shower tray or threshold using 3.2mm(1/8") drill bit and apply silicone into the holes, insert the Wall Anchors (14). Mount the Wall Bracket of the Guide Rail Bracket (2) to the wall using the Screw M5×60 (17). Mount the male parts of the Bottom Mount Clamp(15) onto the shower tray or threshold using the Screw M4X45(10).
SHOWER ENCLOSURES ULTRA-C INSTALLATION STEPS 8. Place the Stationary Glass Assembly back to the designated position. Slide the Guide Rail Bracket (2) to the end side of the Guide Rail(4), fasten the Guide rail bracket (2) to the wall bracket on the wall. Tighten the set screws on the Guide rail brackets. Re-install the Glass Connector (27) to fasten the Return Panel Glass (28) and Upper Guide Rail (4) together. Re-install the Bottom Mount Clamp (15) back to its position. Please see Fig 14 for details a.
SHOWER ENCLOSURES ULTRA-C INSTALLATION STEPS Attention: If you only order one glass door and one stationary glass, please you can skip this step #9 and go to step #10 directly. 9. Install small stationary glass 9.1 Loosen the screw on Mount Clamp (25). Disassemble the Clamp and install the clamp on the Small Stationary Glass (22). The flow Assembly and Installation One glass door and two stationary glass Please see Fig 15 for details a. 25 b. Outside c. 22 Outside 19 25 Figure 15 www.lesscare.
SHOWER ENCLOSURES ULTRA-C INSTALLATION STEPS 21 22 Outside Outside a. b. 21 21 c. 21 4 22 Outside 4 9.2 Install the glass bracket for the Small Stationary Glass (21) to the Upper Guide Rail (4), install the Small Stationary Glass (22) to the guide rail. Outline the position of the wall clamp on the shower base and threshold. Please see Fig 16 for details Figure 16 www.lesscare.
SHOWER ENCLOSURES ULTRA-C INSTALLATION STEPS b. a. 25 25 c. d. Figure 17 9.3 Set the Small Stationary glass assembly aside. Remove the clamp from the Small Stationary Glass and place it back to the outlined position. Now mark the drilling holes on the shower tray or threshold. Please see Fig 17 for details. 21 www.lesscare.
SHOWER ENCLOSURES ULTRA-C INSTALLATION STEPS a. b. Outside Outside c. d. Outside Outside e. f. Outside Outside 9.4. Drill the holes on the shower tray or threshold with 3mm(1/8") drill bit and apply silicone into the holes, insert the Wall Anchors (26). Mount the male parts of the Clamp(25) onto the shower tray or threshold using the Screw M4X45(24). Now put the small stationary glass (22) back to its designated position and fasten it to the upper guide rail and to the shower base or threshold.
SHOWER ENCLOSURES ULTRA-C INSTALLATION STEPS a. 19 Attention: Need to loosen the small allen screws before loosening the long allen screw on the roller 4 b. 5 IMPORTANT: When installing the rollers and handle to the glass door, make sure that clear rubber gaskets are in between the Glass Door (7) and the related hardwares. Tighten the knob and cap on the handle by hand only. Do not use any types of tools to tighten it. Tighten the screws on the roller with related size of Allen Keys (20) only.
SHOWER ENCLOSURES ULTRA-C INSTALLATION STEPS a. 5 7 7 5 5 b. 7 6 5 c. 7 6 Figure 19 d. 1 10. Loosen the Rollers (5) screw and Install the Rollers to the Glass Door (7). And then Install Handle (6) to the Glass Door . At last Install the Bumper Strip(1) to the Glass Door(7). Please see Fig 19 for details REMARK: For style B, there will be no bumper strip installtion step. www.lesscare.
SHOWER ENCLOSURES ULTRA-C INSTALLATION STEPS a. b. 16 13 inside 13 13 d. c. e. inside inside inside f. h. g. inside inside inside Silicone 14 12 Figure 21 11. The slot direction for the Stationary Glass (16) of the Guide Block (13) can be adjusted. Loosen the screw on the bottom of the Guide Block and adjust the direction. Put the Guide Block to the Stationary Glass, make sure that the glass is inside the slot of the Guide Block.
SHOWER ENCLOSURES ULTRA-C INSTALLATION STEPS 7 12. Hang the Glass Door Assembly to the Upper Guide Rail (4), put the bottom edge of the glass door to the slot of the Guide Block (13). Make sure that the Glass Door (6) door will not touch the metal part of the Guide block. See Figure 22 for details. Figure 22 a. b. 7 Inside 7 13 Outside 16 www.lesscare.
SHOWER ENCLOSURES ULTRA-C INSTALLATION STEPS 7 REMARK: For style B installation, please refer to Figure 23. Figure 23 a. b. 14 23 7 Inside 7 Outside 10 14 27 www.lesscare.
SHOWER ENCLOSURES ULTRA-C INSTALLATION STEPS a. 8 16 Outside b. 13 1 8 Figure 24 (for style A only) 13. Slide the Side Anti-Aater Atrip (8) to the Stationary Glass (16), remove the flapper that interfere with the Upper Guide Rail (4) with scissors. See Figure 24 for details. www.lesscare.
SHOWER ENCLOSURES ULTRA-C INSTALLATION STEPS b. 21 b. 23 Outside c. Outside 8 d. 16 8 Outside Outside e. 13 28 23 8 Figure 25 (for style B only) REMARK: For style B installation, please refer to Figure 25. 29 www.lesscare.
SHOWER ENCLOSURES ULTRA-C INSTALLATION STEPS a. 14. Install the Safety Pin(11) to the Glass Door (7). 19 Please see Fig 26 for details IMPORTANT: When installing the safety pins to the glass door, make sure that clear rubber gaskets are in between the Glass Door (7) and the related hardwares and the washer are inside the holes of the glass door. b. Outside c. 28 d. 7 5 7 Outside Figure 26 (for style A only) www.lesscare.
SHOWER ENCLOSURES ULTRA-C INSTALLATION STEPS a. b. 19 11 Outside c. d. Outside e. REMARK: For style B installation, please refer to Figure 27. IMPORTANT: When installing the safety pins to the glass door, make sure that clear rubber gaskets are in between the Glass Door (7) and the related hardwares and the washer are inside the holes of the glass door. Outside Figure 27 (for style B only) 31 www.lesscare.
SHOWER ENCLOSURES ULTRA-C INSTALLATION STEPS a. b. 3 3 c. 5 5 e. 5 d. f. 5 19 19 Figure 28 15. Adjust the Rollers(5) and locate the Glass Door Stoppers(3) Adjust the fasteners on both Rollers (5) to ensure that the bottom edge of the Glass Door (7) will not touch the bottom of the Guide Block (13). NOTE: Glass Door can be adjusted up or down for 2mm by adjusting the fasteners on the Rollers.
SHOWER ENCLOSURES ULTRA-C INSTALLATION STEPS a. 3 b. 5 5 c. 5 Inside Inside e. d. 5 5 11 11 Figure 29 (for style B only) REMARK: For style B installation, please refer to Figure 29. 33 www.lesscare.
SHOWER ENCLOSURES ULTRA-C INSTALLATION STEPS IMPORTANT STEP! 16. Measure and Trim the Anti-Splash Threshold 16.1 Measure the dimension of the threshold opening by attaching the Threshold Cover(11) to the Threshold(9) and place the threshold into the threshold opening. If the threshold is too long to fit into the guide block mark a cut line on the threshold and trim the threshold using a meter saw. Please see Fig 30 Outside Trim th e thres to your hold in accor da door op ening nce Figure 30 www.
SHOWER ENCLOSURES ULTRA-C INSTALLATION STEPS IMPORTANT STEP! REMARK: For style B installation, please refer to Figure 31. Trim the th r to yo eshold in ur do a or op ccordanc ening e Outside Figure 31 (for style B only) 35 www.lesscare.
SHOWER ENCLOSURES ULTRA-C INSTALLATION STEPS IMPORTANT STEP! 16.2 Cut the Anti-splash Threshold if it is necessary Please see Fig 32 9 9 9 Figure 32 www.lesscare.
SHOWER ENCLOSURES ULTRA-C INSTALLATION STEPS 17. Install the Anti-Splash Threshold Pull out the Cover in the guide block (13), put the Anti-Splash Threshold (9) to the slot of the Guide Block, in front of the Glass Door (7) on the shower tray or threshold. Put the Threshold Cover (11) to the end of the Threshold against the wall. Mark a drill hole on a threshold with a pencil. Drill the hole on a threshold with drill bit 8mm (5/16"). Attach the threshold and mark a drill hole on a shower base.
SHOWER ENCLOSURES ULTRA-C INSTALLATION STEPS f. e. 14 Outside Outside g. h. Silicone Outside 9 Silicone 13 i. Outside 11 9 13A www.lesscare.
SHOWER ENCLOSURES ULTRA-C INSTALLATION STEPS REMARK: For style B installation, please refer to Figure 34. a. b. 13A Outside 13B c. 11 Outside 22 11 13A 13B d. Outside Outside Figure 34 (for style B only) 39 www.lesscare.
SHOWER ENCLOSURES ULTRA-C INSTALLATION STEPS f. e. 14 Outside Outside h. g. Outside 9 13 i. 9 Outside Figure 34 (for style B only) www.lesscare.
SHOWER ENCLOSURES ULTRA-C EXTREMELY IMPORTANT INSTALLATION & TECHNICAL MAINTENANCE INSTRUCTIONS EXTREMELY IMPORTANT! The instructions specified and described on this page are extremely important and are required during installation and regular technical maintenance of the product.
SHOWER ENCLOSURES ULTRA-C EXTREMELY IMPORTANT INSTALLATION & TECHNICAL MAINTENANCE INSTRUCTIONS EXTREMELY IMPORTANT INSTALLATION & TECHNICAL MAINTANCE INSTRUCTIONS! A licensed and professional contractor has to comply with the required specifications and dimensions illustrated on this diagram during installation and technical maintenance of the product. 1.
SHOWER ENCLOSURES ULTRA-C EXTREMELY IMPORTANT INSTALLATION & TECHNICAL MAINTENANCE INSTRUCTIONS EXTREMELY IMPORTANT! The instructions specified and described on this page are extremely important and are required during installation and regular technical maintenance of the product.
SHOWER ENCLOSURES ULTRA-C EXTREMELY IMPORTANT INSTALLATION & TECHNICAL MAINTENANCE INSTRUCTIONS EXTREMELY IMPORTANT INSTALLATION & TECHNICAL MAINTANCE INSTRUCTIONS! A licensed and professional contractor has to comply with the required specifications and dimensions illustrated on this diagram during installation and technical maintenance of the product. 1.
SHOWER ENCLOSURES ULTRA-C INSTALLATION STEPS 18. Apply silicone sealant on the seams between the stationary glass /return panel glass and the shower tray/threshold, and between the wall and the stationary glass/return panel glass. See Figure 35 for details. IMPORTANT: MUST ALOW SILICONE TO DRY FOR 24 HOURS BEFORE STARTING USING THE SHOWER ENCLOSURE Figure 35 45 www.lesscare.
SHOWER ENCLOSURES ULTRA-C INSTALLATION STEPS www.lesscare.
SHOWER ENCLOSURES ULTRA-C INSTALLATION STEPS 47 www.lesscare.
SHOWER ENCLOSURES ULTRA-C MAINTENANCE, USE, AND CARE Maintenance & Care IMPORTANT! DO NOT USE: Abrasive cleaners such as: acid, ammonia, bleach, and simmilar solutions; or any types of baking soda cleaning solutions. Use of such solutions may cause corrosion, finish peeling, and/or dull the surface. DO NOT USE: Abrasive sponges or cloth. Never use steel, wool, or wired brushes that will permanently scratch the surface.
