ONE PIECE TOILET Model: LT2T MPN: AN5534 INSTALLATION INSTRUCTIONS Version: 1.1 www.lesscare.
ONE PIECE TOILET LT2T READ ALL INSTRUCTIONS BEFORE UNPACKING THE PRODUCT INSTRUCTIONS THAT, IF IGNORED COULD RESULT IN DEATH OR SERIOUS INJURY CAUSED BY INCORRECT HANDLING OR INSTALLATION OF THE PRODUCT. THESE INSTRUCTIONS MUST BE OBSERVED FOR SAFE INSTALLATION.
ONE PIECE TOILET LT2T DIMENSIONS/TECHNICAL DATA 28-1/4" 15" 15" 10 1/2" 2 1/4" 14 1/4" 8 1/4" 14-1/8" 15" 26 1/4" 18" 2" 11" 1 1/2" 5 1/2" Rough- in 12" Standard ATTENTION! Dimensions may vary by up to 3/8". It is highly recommended to pull all dimensions of actual model for installation and measuring purposes. TECHNICAL DATA • Single flush 1.28 GPF www.lesscare.
ONE PIECE TOILET LT2T WATER SUPPLY LOCATION & TECHNICAL INFORMATION Side View Back View Threaded Shunk (Water Supply Fill Valve) Wall Supply Position 1 Supply Position 2 3" 5 1/2" 5 1/2" 5 1/2" Rough-in 12" Standard Floor 4 1/2" 10" Wall Side View You may connect the water supply line using two different options. In both options distance from the floor to the center of the supply line must be 5 1/2".
ONE PIECE TOILET LT2T INSTALLATION INSTRUCTIONS IMPORTANT! Shut off main water supply prior to installation! REMOVE OLD TOILET 1. Shut off water supply line. If you do not have shut-off valve near the toilet shut off main water supply line. 2. Flush the old toilet and make sure that tank is empty. 3. Disconnect and remove water supply line connected to the toilet's tank. 4. Remove old toilet, bolts, nuts from the closet flange. 5.
ONE PIECE TOILET LT2T INSTALLATION INSTRUCTIONS INSTALL NEW TOILET Wall Step 1. Lift and carefully put the toilet over the closet flange so the closet bolts can go through the mounting holes in the toilet's base. Once the bowl is in the position press the bowl down with slight twisting motion in level position towards the floor. Apply your body weight to evenly compress the wax ring to create watertight seal. Make sure that the bowl is as leveled as possible to have a nice seal tight.
ONE PIECE TOILET LT2T TOILET SEAT INSTALLATION 6 Seat cover 5 Hinge 4 Adjustment plate 3 Screw 2 Washer 1 Nut 1.Fit the screw through the adjustment plate,then put the adjustmentplate into the hinge 2. Place the assembly onto the toilet and push the screws into the holes. Make the necessary adjustments to the fittings so that the seat sits correctly on the toilet. Once correctly positioned fit the washer and nut and secure the seat.
ONE PIECE TOILET LT2T ADJUSTMENT & MAINTENANCE (SINGLE VALVE) Important Note: Flush GPF amount is factory set. No additional adjustment is required. This page is for reference only. All adjustments are already made by manufacturer. BASE INSTALLATION Body metal anchor Remove body of the valve Place one end of the metal anchor into the ceramic hole and then the other end. Use a screwdriver to tighten the valve sufficiently to avoid leakage.
ONE PIECE TOILET LT2T ADJUSTMENT & MAINTENACE (FILL VALVE) Important Note: Flush GPF amount and fill valve are factory set. No additional adjustment is required. This page is for reference only. All adjustments are already made by manufacturer. Refill tube (the refill tube is optional based on the user's requirement. fill valve 87-231mm flush valve overflow When valve installed, the critical level mark on fill valve (identified by C.L.
ONE PIECE TOILET LT2T CLEANING & TROUBLESHOOTING (FILL VALVE) FILL VALVE CLEANING (Filter which is located inside the inlet valve shank is require for cleaning periodically) 1 3 2 4 5 brush shut off water supply Shut off the water supply valve (angle stop) then reomove the water supply line from the adaptor. inlet pipe filter Clean the filter screen with water Remove the filter sreen from the inner portion of the shank Re-install clean filter back into the inner portion of the shank.