ONE PIECE TOILET Model: LT3 MPN: B0940 INSTALLATION INSTRUCTIONS Version: 1.0 www.lesscare.
ONE PIECE TOILET LT3 READ ALL INSTRUCTIONS BEFORE UNPACKING THE PRODUCT INSTRUCTIONS THAT, IF IGNORED COULD RESULT IN DEATH OR SERIOUS INJURY CAUSED BY INCORRECT HANDLING OR INSTALLATION OF THE PRODUCT. THESE INSTRUCTIONS MUST BE OBSERVED FOR SAFE INSTALLATION.
ONE PIECE TOILET LT3 DIMENSIONS/TECHNICAL DATA 28 1/2" 10 1/4" 15 3/8" 14 1/2" Ø2 1/8" 14 1/4" 2 1/2" 7 1/4" 2" 13" 16 1/2" 27 1/2" 18" 1 1/2" 11 " 1 1/2" 5 1/2" Rough-in 12" Standard ATTENTION! Dimensions may vary by up to 3/8". It is highly recommended to pull all dimensions of actual model for installation and measuring purposes. TECHNICAL DATA • Dual flush: 0.9 /1.58 GPF www.lesscare.
ONE PIECE TOILET LT3 WATER SUPPLY LOCATION & TECHNICAL INFORMATION Side View Back View Wall Threaded Shunk (Water Supply Fill Valve) Supply Position 1 15" Supply Position 2 3" 5 1/2" 5 1/2" 5 1/2" Rough-in 12" Standard 12" Floor 4 1/2" 10" You may connect the water supply line using two different options. In both options distance from the floor to the center of the supply line must be 5 1/2".
ONE PIECE TOILET LT3 INSTALLATION INSTRUCTIONS IMPORTANT! Shut off main water supply prior to installation! REMOVE OLD TOILET 1. Shut off water supply line. If you do not have shut-off valve near the toilet shut off main water supply line. 2. Flush the old toilet and make sure that tank is empty. 3. Disconnect and remove water supply line connected to the toilet's tank. 4. Remove old toilet, bolts, nuts from the closet flange. 5.
ONE PIECE TOILET LT3 INSTALLATION INSTRUCTIONS INSTALL NEW TOILET Wall Step 1. Lift and carefully put the toilet over the closet flange so the closet bolts can go through the mounting holes in the toilet's base. Once the bowl is in the position press the bowl down with slight twisting motion in level position towards the floor. Apply your body weight to evenly compress the wax ring to create watertight seal. Make sure that the bowl is as leveled as possible to have a nice seal tight.
ONE PIECE TOILET LT3 TOILET SEAT ADJUSTMENT ADJUST SOFT-CLOSE SEAT If your toilet seat becomes loose or is not properly aligned to the toilet's bowl and requires adjustment you may adjust the position of the seat. 1. Press push-to-release buttons in simultaneously with two thumbs and lift the toilet seat up. 2. Lift the cover cap 3. Using a philips screwdriver make 1-2 turns to loosen the screw slightly (do not unscrew the screw completly) 4. Put your toilet seat back on to the pins.
ONE PIECE TOILET LT3 ADJUSTMENT & MAINTENANCE (DUAL FLUSH VALVE) Important Note: Flush GPF amount is factory set. No additional adjustment is required. This page is for reference only. All adjustments are already made by manufacturer. 1.
ONE PIECE TOILET LT3 ADJUSTMENT & MAINTENACE (FILL VALVE) Important Note: Flush GPF amount is factory set. No additional adjustment is required. This page is for reference only. All adjustments are already made by manufacturer. Instructions: When valve installed, the critical level mark on fill valve (identified by C.L. mark on valve body) shoud be at least 1" above top of the over flow pipe.
ONE PIECE TOILET LT3 CLEANING & TROUBLESHOOTING (FILL VALVE) FILL VALVE CLEANING Shut off water supply line before filter cleaning. Carefully, take out the filter from inlet by using pliers. Use water to wash and clean the filter and adapter from any debris. Re-install the filter and re-connect the water supply line.
