Owner manual

ManualsBrandsLevel Mount ManualsTV AccessoriesStudfinder

www.levelmount.com

1-888-229-1459

EU: +0044 844 567 2657

UK: 0844 567 2657

Operating Tips:

1. This Stud Finder is not suitable for use on walls or ceilings insulated with metallic foil/ﬁ ber composition, or on walls of lath and heavy

drag plaster surfaces.

2. It is important to double check the location of the stud with several readings.

3. An object such as wire, pipe, conduit, or braces inside the wall may read as a stud or joist. Before mounting the TV Wall Mount to the

wall, ensure you have located a wooden stud.

4. Extreme care should be exercised when drilling, sawing, or nailing in walls, ceilings, and ﬂ oors, where plumbing or electrical wires may

be located.

5. When the wall is thick or dense, a fast blinking Red LED light will indicate the nearest stud edge.

6. To avoid interference and inaccuracy, keep your free hand away from the unit while operating.

7. After you have determined the spot where you believe the center of the stud to be (using the Stud Finder), hammer a small nail into

that spot to conﬁ rm that you are hammering into solid wood (and not something less dense, like particle board).

Stud Finder Instructions

How to Use:

Step 1 – Calibrating the Stud Finder

Remove the plastic tab from the battery to operate. Place the Stud Finder on the wall. Press and hold down the

Operating Button. The Red LED light is bright and quickly changes to a duller constant light, which means that the

calibration is complete and the unit is ready for use.

Step 2 – Operating Stud Finder

Continue pressing the Operating Button while slowly moving the unit across the wall in one direction. Move the

Stud ﬁ nder from left to right without lifting up or tilting.

Step 3 – Locating the Edge of the Stud

Continue to slide the Stud Finder along the wall. A steady red light will start to blink slowly and then fast. The fast

blinking means the sensor is on top of or near the edge of the stud.

Step 4 – Marking the Edge of the Stud

Use a pencil to mark the edge of the stud.

Step 5 – Locating the Other Edge of the Stud

Release the Operating Button and go to the other side of the stud and repeat the process on the stud in the

opposite direction

Step 6 – Marking the Other Edge of the Stud

Use a pencil to mark the other side of the stud edge. Now both sides of the stud should be marked on the wall.

Step 7 – Marking the Center of the Stud

With a pencil, mark a point in the middle of the two lines. This is the center of the stud.

Summary of content (4 pages)

PAGE 1
Stud Finder Instructions Operating Tips: 1. This Stud Finder is not suitable for use on walls or ceilings insulated with metallic foil/fiber composition, or on walls of lath and heavy drag plaster surfaces. 2. It is important to double check the location of the stud with several readings. 3. An object such as wire, pipe, conduit, or braces inside the wall may read as a stud or joist. Before mounting the TV Wall Mount to the wall, ensure you have located a wooden stud. 4.
PAGE 2
Stud Finder Instructions Specifications: The operating temperature range is from 14°F to 122°F (-10°C to +50°C), with the best temperature being up to 77 F (25°C), humidity below 60% and altitude up to 6,500 feet (2,000 meters). Do not use the Stud Finder in conditions that are not within these parameters or it may not function correctly. 1. The detector must not be used in the presence of moisture such as dew or rain. 2. Do not operate the detector with the battery cover removed.
PAGE 3
Instrucciones del Detector de Madera Instructions – Localisateur de montants Especificaciones: La temperatura media de funcionamiento es de 14°F a 122°F (-10°C a +50°C); la mejor temperatura es 77ºF (25°C), con humedad por debajo de 60% y una altitud de hasta 6.500 pies (2.000 metros). No utilice el Detector de Madera en condiciones que no estén dentro de dichos parámetros, pues podría funcionar mal. 1. No utilice el detector en condiciones de mucha humedad, como el rocío o lluvia. 2.
PAGE 4
Instructions – Localisateur de montants Instrucciones del Detector de Madera Consejos de operación: Specifications : La température d’utilisation est comprise entre 14° F et 122° F (-10° C à +50° C), la température idéale étant de 77 F (25° C), l’humidité en dessous de 60% et ‘altitude jusqu’à 6 500 pieds (2 000 mètres). 1. Le détecteur ne doit pas être utilisé en présence d’humidité ou en cas de pluie. 2. Ne pas utiliser si la protection des piles est enlevée.