User's Manual

ManualsBrandsLeviton Manufacturing ManualsElectronicsIn Wall Dimmer

PRELIMINARY

Testing your Dimmer prior to mounting in

wall box:

LIMITED 5 YEAR WARRANTY AND EXCLUSIONS

Leviton warrants to the original consumer purchaser and not for the benefit of anyone else that this product at the time of its sale by Leviton is free of defects in materials and workmanship under normal and proper use for five years from the purchase date. Leviton’s only obligation is to correct such defects by repair or replacement, at its option, if within such five year period the product is returned prepaid, with proof of purchase

date, and a description of the problem to Leviton Manufacturing Co., Inc., Att: Quality Assurance Department, 59-25 Little Neck Parkway, Little Neck, New York 11362-2591. This warranty excludes and there is disclaimed liability for labor for removal of this product or reinstallation. This warranty is void if this product is installed improperly or in an improper environment, overloaded, misused, opened, abused, or altered in any

manner, or is not used under normal operating conditions or not in accordance with any labels or instructions. There are no other or implied warranties of any kind, including merchantability and fitness for a particular purpose, but if any implied warranty is required by the applicable jurisdiction, the duration of any such implied warranty, including merchantability and fitness for a particular purpose, is limited to five years.

Leviton is not liable for incidental, indirect, special, or consequential damages, including without limitation, damage to, or loss of use of, any equipment, lost sales or profits or delay or failure to perform this warranty obligation. The remedies provided herein are the exclusive remedies under this warranty, whether based on contract, tort or otherwise.

Step 5

• Restore power at circuit breaker or

fuse.

•

Press pad until locator light is OFF.

Lights should turn ON. If lights do not

turn ON, press the upper half of DIM/

BRIGHT bar until the lights brighten.

If lights still do not turn ON, refer to

the TROUBLESHOOTING section.

TROUBLESHOOTING

• Lights Flickering

- Lamp has a bad connection.

- Wires not secured firmly under terminal screws of dimmer

and/or remote.

- Local switch, ON

• Light does not turn ON and Locator LED does not

turn ON

- Circuit breaker or fuse has tripped.

- Lamp is burned out.

- Lamp Neutral connection is not wired.

- Confirm that the device is being supplied from a 120V, 60Hz

AC source ONLY.

- Confirm that unit is programmed properly. Repeat “TO INSTALL”

section to verify that it has been included in the Z-Wave™

network.

• Intermittent dimmer operation

- Minimum load is under 40W.

- Confirm that the Load being controlled does not exceed the

600W dimmer limit.

• Remote does not operate lights

- Ensure that total wire length does not exceed 300 ft.

For additional information, contact Leviton’s Techline

1-800-824-3005

or visit Leviton's website at

www.leviton.com

NOTE: Dress wires with a bend as shown in diagram in order to

relieve stress when mounting device.

• Position all wires to provide room

in outlet wall box for device.

• Ensure that the word "TOP" is

facing up on device strap.

• Partially screw in mounting screws

in wall box mounting holes.

Step 6

Including Scene Capable Dimmer into

Z-Wave™ Network:

NOTES:

• If using a non-Leviton Programmer/Controller, refer to the

Programmer/Controller instruction sheet for Including a device.

A) If using a Leviton Z-Wave™ Programmer/Controller, Cat. No.

RZCPG, press the Menu button and scroll down to System

Setup. Press the center button to select System Setup Menu.

Press the center button to select Network.

Menu Button

B) While standing close to the module (approx. 2-5 ft), press the

center button to <Include> device in the network.

NOTE: Only one device may be included at a time. DO NOT

put multiple devices into the Inclusion mode at any time.

C) While the Programmer/Controller is in

the Inclusion mode and the Locator

LED is ON on the dimmer, push the

push pad to turn ON the dimmer. The

Programmer/Controller will verify

inclusion and the locator LED will turn

OFF on the dimmer.

If the dimmer is flashing Amber while

in the Inclusion mode, the

Programmer/Controller is still trying to

communicate with the dimmer. Wait

until the device stops flashing,then

press push pad.

NOTE: If the locator LED on the

dimmer turns solid Red while

including, there has been a communication error. Refer to

Troubleshooting section.

D) The Primary Programmer/Controller wil assign a node ID

number (Name) for this module.

NOTE: This ID number (Name) will be stored in the controller

library to be used for future reference.

NOTE: You may name or edit the node of this device at this

time.

E) The dimmer is now installed in the network.

NOTE: If a dimmer has been successfully Included in the network

and the user tries to Include it again without first excluding it from

the network, the module will retain the first node ID it had received

and ignore the second.

Excluding Dimmer from Network:

NOTE: It is very important to accurately Exclude

devices from the network when moving or removing a

device from a Z-Wave™ network. This ensures that all

information has been removed from your Primary

Programmer/Controller’s information table and is not

counted on to be a part of the mesh network.

A) If using a Leviton Z-Wave™ Programmer/Controller, Cat.

No. RZCPG, press the Menu button and scroll down to

NOTE: Remote must be in close proximity to

dimmer when including in the network.

RZCPG

Programmer/Controller

Step 7

System Setup. Press the center button to select System

Setup Menu. Press the center button to select Network.

B) While standing close to the module, press the center

button to <Exclude> device from the network.

C) While the Programmer/Controller is in the Exclusion mode

and the locator LED is ON on the dimmer, press the push

pad on the dimmer. The Programmer/Controller will verify

Exclusion and the locator LED will turn OFF on the dimmer.

If the dimmer is flashing Amber while in the Exlusion mode,

the Programmer/Controller is still trying to communicate

with the dimmer. Wait until the device stops flashing, then

press the push pad.

Factory Default:

If your dimmer is not responding, or you are unable to control it after

you have tried to Include/Exclude it multiple times, it may be

necessary to reset the dimmer to its original factory settings. To

accomplish this, proceed as follows:

• On the dimmer, engage he air-gap switch (refer to Operation

section) and wait 5 seconds. Press push pad back into frame

and hold push pad until the locator LED flashes Amber and turns

solid Red. The dimmer is now reset. Once the dimmer

is reset, it will be necessary to Re-Include it to a network before it

can be used.

CAUTION: SETTING A DEVICE TO A FACTORY DEFAULT DOES

NOT EXCLUDE THAT DEVICE FROM A NETWORK. THE

EXCLUSION PROCEDURE MUST STILL BE FOLLOWED TO

REMOVE THE DEVICE FROM THE PRIMARY CONTROLLER’S

INFORMATION TABLE. FAILURE TO DO SO MAY RESULT IN A

SYSTEM THAT IS SLOW TO RESPOND, OR MAY FAIL TO

RESPOND TO SOME DEVICES.

Dimmer Mounting:

TURN OFF POWER AT CIRCUIT BREAKER OR FUSE.

Restore Power: Restore power at circuit breaker or

fuse. Installation is complete.

Installation may now be completed by

tightening mounting screws into wall box.

Attach wallplate.

Step 8

OPERATION

NOTE: The locator light will illuminate

when the load is in the OFF position to

facilitate access in the dark.

NOTE: If using the dimmer in a 3-way

application, the lights will turn ON at

brightness set on dimmer's DIM/BRIGHT

bar. The lighting can be controlled from

either the dimmer or the remote location.

Gently lift bottom

of push pad out

Push Pad (Default settings)

Turn ON from OFF position:

Tap – Lights turn ON to preset level.

Press and Hold – Lights turn ON to full bright.

Turn OFF from ON position:

Tap – Lights turn OFF.

Press and Hold until lights DIM to lowest level and LED in LED

Brightness Display starts to blink – Lights remain ON for 10

seconds and then turn OFF.

DIM/BRIGHT Bar

BRIGHTEN:

Press upper half of DIM/BRIGHT Bar – Lights brighten to desired level.

DIM:

Press lower half of DIM/BRIGHT Bar – Lights dim to desired level.

If you continue to hold the lower half of the DIM/BRIGHT Bar, the

lights will DIM to minimum level and then turn OFF.

NOTE: When lights are OFF you can change the light level that the

lights will turn ON to using the DIM/BRIGHT Bar.

If there is a power outage, when the power is restored the lights will

return to the last setting before the power

interruption.

LED

Brightness

Display

DIM/BRIGHT

Bar

Push

Pad

Locator

Light

Step 9

Air-Gap Switch: On the dimmer only,

engage the air-gap switch by gently pulling

the bottom of the push pad until it lifts

completely out of the frame and a click is

heard and all LED’s are OFF (refer to

Figure). This will cut power to the fixture to

replace the bulb. After servicing is

complete, push the push pad back for

normal operation.

Cleaning: Clean with a damp cloth. DO

NOT use chemical cleaners.

ADVANCED PROGRAMMING FEATURES

Mode 1 – Set Minimum Brightness: Set the minimum brightness

level that the lights can dim to prior to turning full OFF.

Mode 2 – Set Dim-Lock: Set the brightness level that the lights

will turn on to regardless of the previous light level at which they

were turned OFF.

Mode 3 – Set Fade Rate: Set the amount of time (in seconds) that

the lights will have to turn ON or OFF. Fade rates can be set to

one of five different settings.

To Program:

NOTE: Have a flashlight handy if this dimmer

controls the only light source in the room.

1. On the dimmer only, engage the air-gap

switch by gently pulling the bottom of the

push pad until it lifts completely out of the

frame and a click is heard and all LED’s are

OFF.

2. Press push pad back into frame and hold

push pad for 7 seconds until the locator light

and the top LED (LED 1) starts blinking.

3. Upon releasing the push pad, the locator

light will continue to blink once per second

indicating the dimmer is in Mode 1, Set

Minimum Brightness mode. To change the

current Minimum Brightness level from 1-50%, use the DIM/BRIGHT

Bar. This setting will automatically be saved.

4. Tap the push pad to change to Mode 2, Set Dim-Lock Level mode.

The locator light will blink twice per second. To change the current

Set Dim-Lock level from 1-100%, use the DIM/BRIGHT Bar. If this

feature is not desired, press and hold the lower half of the DIM/

BRIGHT Bar until no LED is lit. This setting will automatically be

saved.

5. Tap the push pad to change to Mode 3, Set Fade Rate mode. The

locator light will blink 3 times per second. To change the current

Fade Rate, use the DIM/BRIGHT Bar to move the LED to the

desired preset level. This setting will automatically be saved by

tapping the push pad to exit programming mode.

The LED Brightness Display is separated into 7 segments. Each LED

represents a preset level with LED 1 (Preset 1) located at the top and

LED 7 (Preset 7) located at the bottom. Refer to chart for settings and

defaults.

NOTE: The dimmer will exit program mode after 3 minutes of activity.

* default

** LED #1 is located at the top

*** The press and hold feature for the 10 second delayed off is

disabled in this mode.

Preset LED

** Fade On Fade Off

1* 1 Approx. 1.5s from full off Approx. 3s from full on

*** 2 No Fade No Fade

3 3 No Fade Approx. 3s from full on

4 4 Approx. 0.5s from full off Approx. 3s from full on

5 5 Approx. 0.5s from full off Approx. 1.5s from full on

6 6 Approx. 1.5s from full off Approx. 5s from full on

7 7 Approx. 1.5s from full off Approx. 10s from full on

Fade Rate Presets

Mode Description Range Default

1 Set Min. Brightness 1-50% 25%

2 Set Dim-Lock Level 0-100%, 0=no lock 0

3 Select Fade Rate 1, 2, 3, 4, 5, 6 or 7 Preset #1

Advanced Features Summary

LED

Brightness

Display

DI-000-RZI06-00A-X0

U.S. & Foreign Patents Pending

2006 Leviton Manufacturing Co., Inc.

All Rights Including Trade Dress Rights Reserved

OFF

Programmer/Controller

Cat. No. RZCPG

Center Button