User's Manual

ManualsBrandsLeviton Manufacturing ManualsElectronicsDimmers

LIMITED 5 YEAR WARRANTY AND EXCLUSIONS

Leviton warrants to the original consumer purchaser and not for the benet of anyone else that this product at the time of its sale by Leviton is free of defects in materials and workmanship under normal and proper use for ve years from

the purchase date. Leviton’s only obligation is to correct such defects by repair or replacement, at its option, if within such ve year period the product is returned prepaid, with proof of purchase date, and a description of the problem to

Leviton Manufacturing Co., Inc., Att: Quality Assurance Department, 201 North Service Road, Melville, New York 11747. This warranty excludes and there is disclaimed liability for labor for removal of this product or reinstallation.

This warranty is void if this product is installed improperly or in an improper environment, overloaded, misused, opened, abused, or altered in any manner, or is not used under normal operating conditions or not in accordance with any

labels or instructions. There are no other or implied warranties of any kind, including merchantability and tness for a particular purpose, but if any implied warranty is required by the applicable jurisdiction, the duration of any such

implied warranty, including merchantability and tness for a particular purpose, is limited to ve years. Leviton is not liable for incidental, indirect, special, or consequential damages, including without limitation, damage to, or

loss of use of, any equipment, lost sales or prots or delay or failure to perform this warranty obligation. The remedies provided herein are the exclusive remedies under this warranty, whether based on contract, tort or otherwise.

OPERATION

NOTE: For complete details on operating the

Primary Programmer/Remote, refer to the

instruction guide for that particular device.

The VRC0P is intended for use by developers

who want to develop products that can

transmit signals to and receive signals from

Vizia RF +

products on a Z-Wave

network. A

relatively high level of programming knowledge

is required to develop products that use these

interfaces. The interface uses a simple ACSII

protocol to communicate to the controlling

equipment. If you are an end user who has

purchased this product to work with another

product that was designed for this purpose,

please refer to that product’s owner’s manual for

operating instructions.

If you are a developer who has purchased this

interface to develop a Vizia RF +

compatible

product, you will need the VRC0P Tech Note,

which contains the information needed to allow

proper interface communication. Please visit our

website listed below to download the VRC0P

Tech note.

• Plug-In Serial Interface Module is

functioning improperly

- Conrm that the device is being supplied

from a 120V, 60Hz AC source ONLY.

- Conrm that the unit is programmed

properly. Repeat “INSTALLING YOUR

INTERFACE MODULE” section to verify

that it has been included into the Z-Wave

network.

• Programmer/Remote does not operate

lights

- Check association.

- Ensure that Plug-In Serial Interface Module

was properly updated.

TROUBLESHOOTING

DI-000-VRC0P-02A-X1

For additional information, contact Leviton’s

Techline at 1-800-824-3005 or visit Leviton’s

website at www.ViziaRFplus.com

Protected under U.S. Patent Number 6,388,399

and patents pending and licensed under U.S.

Patents Numbers 5,905,442, and 5,982,103

NOTE: It is very important to accurately

Exclude devices from the network when

moving or removing a device from a Z-Wave

network. This ensures that all information has

been removed from your Primary Programmer/

Remote’s information table and is not counted

on to be a part of the mesh network.

) If using a Leviton Z-Wave

Programmer/

Remote, Cat. No. VRCPG, press the Menu

button and scroll down to System. Press

the center button to select System Menu.

Choose Advanced. Press the center button

to select Advanced Install. Scroll down

to <Exclude Node> and press the center

button.

B) If using VRCPG Programmer/Remote

you will be prompted to prepare device

for exclusion. To do this, you must put

the Plug-In Serial Interface Module into

programming mode.

C) To access Program mode, press and hold

programming button until the LED turns

Amber. Release the button and the LED will

blink Amber. You are now in Programming

mode.

NOTE: If the LED on the Plug-In Serial

Interface Module turns solid Red while

excluding, there has been a communication

error.

D) While standing close to the Plug-In Serial

Interface Module (approximately 1 ft.),

press the center button to <Exclude> device

from the network.

Excluding Plug-In Serial

Interface Module from

Network:

Step 4

Factory Default:

If your module is not responding, or you are

unable to control it after you have tried to Include/

Exclude it multiple times, it may be necessary to

reset the module to its original factory settings. To

accomplish this, proceed as follows:

• Press and hold the programming button until

the LED turns Amber and then turns Red.

Release the button and wait until the LED

starts blinking Green. NOTE: This can take up

to a minute. The module is now reset. Once

the module is reset, it will be necessary to Re-

Include it to a network before it can be used.

CAUTION:

SETTING A DEVICE TO A

FACTORY DEFAULT DOES NOT EXCLUDE

THAT DEVICE FROM A NETWORK. THE

EXCLUSION PROCEDURE MUST STILL BE

FOLLOWED TO REMOVE THE DEVICE FROM

THE PRIMARY REMOTE’S INFORMATION

TABLE. FAILURE TO DO SO MAY RESULT IN

SYSTEM THAT IS SLOW TO RESPOND, OR

MAY FAIL TO RESPOND TO SOME DEVICES.

IF YOU HAVE TO RESET THE CONTROLLER

WITHOUT EXCLUDING IT GO TO THE REMOVE

FAILED MENU AND REMOVE THIS DEVICE

FROM YOUR VRCPG REMOTE. REFER TO

VIZIA RF+ APPLICATION GUIDE

(WWW.LEVITON.COM).

Wall Receptacle

RS232 Cable

Plug-In Serial

Interface Module

NOTE: Programmer/Remote must be in close

proximity (approx. 1 foot) to Plug-In Serial

Interface Module when including into network

VRCPG Programmer/

Remote

Including Plug-In

Serial Interface

Module into

Z-Wave

Network:

Step 3 cont’d Step 4 cont’d

COMMUNICATION SETTINGS

NOTE: The following general information applies

to the RS232 Interface.

To congure your device to communicate with the

interface, use the following data conventions:

9600 BAUD

8 DATA

1 STOP

NO PARITY

If you wish to send these commands from a

PC, run the Microsoft Windows

Hyper Terminal

program or an equivalent program. Then select

Local Echo, Line Feed and Carriage Return

inbound and outbound. This allows you to see the

characters that you are typing as well as keep the

responses from overwriting typed characters.

www.ViziaRFplus.com

RJ11 DB9 PIN-OUTS

4 (BLACK)

3 (RED)

2 (GREEN)

1 (YELLOW)

2 (TX)

(Not used)

3 (RX)

5 (SGND)

RJ11 RJ11 HAI PATCH CORD PIN-OUTS

4 (BLACK)

2 (GREEN)

3 (RED)

1 (YELLOW)

1 (TX)

2 (RX)

(Not used)

4 (SGND)

FCC COMPLIANCE STATEMENT

This device complies with Part 15 of the FCC

Rules. Operation is subject to following two

conditions: (1) this device may not cause

harmful interference, and (2) this device must

accept any interference received, including

interference that may cause undesired

operation of the device.

This equipment has been tested and found

to comply with the limits for a Class B Digital

Device, pursuant to Part 15 of the FCC

Rules. These limits are designed to provide

reasonable protection against harmful

interference in a residential installation.

This equipment generates, uses, and can

radiate radio frequency energy and, if not

installed and used in accordance with the

instructions, may cause harmful interference

to radio communications. However, there is

no guarantee that interference will not occur

in a particular installation. If this equipment

does cause harmful interference to radio or

television reception, which can be determined

by turning the equipment OFF and ON,

the user is encouraged to try to correct the

interference by one or more of the following

measures:

• Reorient or relocate the receiving Antenna.

• Increase the separation between the

equipment and the receiver.

• Connect the equipment into an outlet on

a circuit different from that to which the

receiver is connected.

• Consult the dealer or an experienced radio/

tv technician for help.

FCC CAUTION

Any changes or modications not expressly

approved by Leviton Manufacturing Co., Inc.,

could void the user's authority to operate the

equipment.