User's Manual

ManualsBrandsLeviton Manufacturing ManualsElectronicsWSS0S

Dip Switches 1-4

Single Pole (One Location)

Wireless Occupancy Sensor Products

Cat. No. WSS10, WSC04, WSC15, and WSS0S

Incandescent 800W @ 120V

Ballast 1200VAC @ 120V, 2700VA @ 277V

120-277VAC, 50-60Hz, Motor:

HP @ 120V

INSTALLATION INSTRUCTIONS

WARNINGS AND CAUTIONS:

• To be installed and/or used in accordance with appropriate electrical codes and regulations.

• If you are unsure about any part of these instructions, consult a qualiﬁed electrician.

• WSS0S Wireless Remote Switch can be used for additional switches (3-way and 4-way), no wires necessary.

WARNINGS AND CAUTIONS:

• Disconnect power at circuit breaker or fuse when servicing, installing or removing ﬁxture.

• Use this device only with copper or copper clad wire. With aluminum wire use only devices marked CO/ALR or CU/AL.

• Recommended minimum wall box depth is 2-1/2”.

Tools needed to install your Switch:

Slotted/Phillips Screwdriver Electrical Tape Pliers

Pencil Cutters Ruler

Wire Nuts

DIP SWITCH SETTINGS:

Manual ON / Auto ON mode: (factory: manual mode) Occupancy Sensor

WSC** - Auto mode can be enabled with the use of additional (3) AAA

batteries or a 5-24VDC connection.

Walk-through: On or Off (can be used only in Auto-ON mode)

Timeout: 2, 10, 20, 30min

Cat. No. WSS10 has a single switch pad that toggles the relay and its

corresponding load, ON and OFF. If the relay is OFF, the relay will turn

ON when the push-button is pressed, and remain ON in the presence of

motion. In the absence of motion, the Sensor Unit will Time-Out and turn

relay OFF. If in Auto ON/Manual OFF, time delay will start once space is

vacant.

NOTES:

• When the lights are on, the Motion Indicator LED will blink red (1 blink

per minute) every time motion is detected.

• When the Time-Out expires and the relay turns OFF, a 30 second

vacancy conﬁrmation exists to turn the relay back ON.

• In Manual-ON mode, the button must be pressed to turn the lights ON.

In the absence of motion, the unit will Time-Out and turn the lights OFF.

LEARN MODE:

When using the Wireless Occupancy Products together, they must

LEARN the other devices to perform as desired.

• WSC04 and WSC15 – Wireless Occupancy Sensor – has learn button

on device, under front plastic tab

• WSS10 – Wireless Momentary Control Switch – use switch pad for

learning

• WSS0S – Wireless Remote Switch – use switch pad for learning

Programming – using Momentary Switch (WSS10)

• To enter programming, press and hold the switch pad for 15 seconds

• When in programming mode,

1 AMBER LED ﬂash, 1 second pause = in programming

There are 2 modes in programming, LEARN and CLEAR modes. Tap the

switch pad to select which mode you would like.

• 1 AMBER LED ﬂash = LEARN mode

• 2 AMBER LED ﬂashes = CLEAR mode

Once you have selected the desired programming mode, press and hold

the pad again for 5 seconds to ENTER the desired mode.

• Learn mode:

• 1 Red ﬂash = no learned devices

• 1 Green ﬂash = 1 learned devices

• 2 Green ﬂashes = 2 learned devices

• 3 Green ﬂashes = 3 learned devices

• Etc. (up to 6 devices)

• On remote switch or occupancy sensor, you must press the switch pad

to send a signal for learning.

• AMBER LED on for 2 seconds = acknowledgement, device is

learned

• GREEN LED on for 2 seconds = device is unlearned

INSTALLING YOUR SWITCH

NOTE: Use check boxes when Steps are completed.

Changing the color of your Switch:

Color change kits are available from Leviton. To change color of frame,

proceed as follows:

Line up tabs and

press in side to attach

Push in side

at tab to release

/./&&

/./&&/./&&

/./&&

WARNING: TO AVOID FIRE SHOCK OR DEATH; TURN

OFF POWER at circuit breaker or fuse and test that power is

off before wiring!

Step 1

Black Wire (BK)

Blue Wire (BL)

White Wire (WH)

Single Pole Wiring Application:

Step 3a

Single Pole

1. Line (Hot)

2. Neutral

3. Ground

4. Load

Identifying your wiring application (most common):

NOTE: If the wiring in your wall box does not resemble this

conﬁguration, consult a qualiﬁed electrician.

Step 2

Step 3b cont'd

Factory Settings: The sensor is shipped from the factory to work in almost

all situations, without any adjustments. The factory settings are: Manual

mode, when entering the room, the wireless momentary switch will need

to be turned ON. Wireless occupancy sensor will keep the lights on until

the room is vacant then turn the lights OFF after timeout period. The PIR

technology is active. Factory time-out is 10 min.

Time-Outs: The Sensor has four time-out settings: 2, 10, 20, or 30 min.

• Fixed Time-Out: The value of this time-out is user selected through the

use of the Dip Switch Settings.

Walk-Through Time Delay: The walk-through feature, which is only active

in the Auto-On mode, is useful when a room is momentarily occupied.

With this feature, the Sensor will turn the lights OFF shortly after the

person leaves the room. The walk-through feature works in the following

manner: When a person enters the room, the lights will turn ON. If the

person leaves the room before the walk-through time-out of 2.5 minutes,

the Sensor will turn the lights OFF within 2.5 minutes of no occupancy

detected. If the room is occupied for longer than 2.5 minutes, the Sensor

will enter the Occupied Mode with the time-out duration speciﬁed by the

Dip Switch setting.

Hot (Bla c k )

Neutral (White)

Load

Swit c h

BK WH

Bla c k

White

Line

120 V A C , 60H z

WIRING SWITCH:

Connect wires per WIRING DIAGRAM below as follows:

• Connect (Hot) wire from wall box to black wire on switch.

• Connect (Load) wire in wall box to blue wire on switch.

• Connect (Neutral) wire in wall box to white wire on switch.

NOTE: For NO Neutral model, white wire will not be available.

NOTE: For 3-way applications, 4-way and more, use the

WSS0S Wireless Remote.

Step 3b cont'd

Single Pole Wiring Application:

Step 3b

NOTE: To access dip switch settings, lift up the bottom of the

switch pad.

DIP SWITCH SETTINGS

Dip Switch OFF Position ON Position

1 Auto ON/Manual OFF Manual ON

2 Walk Through OFF Walk Through ON

2 Min Time-Out OFF Position ON Position

3 X -

4 X -

10 Min Time-Out OFF Position ON Position

3 X -

4 - X

20 Min Time-Out OFF Position ON Position

3 - X

4 X -

30 Min Time-Out OFF Position ON Position

3 - X

4 - X

Summary of content (3 pages)

PAGE 1
Single Pole (One Location) Wireless Occupancy Sensor Products Cat. No. WSS10, WSC04, WSC15, and WSS0S Incandescent 800W @ 120V Ballast 1200VAC @ 120V, 2700VA @ 277V 120-277VAC, 50-60Hz, Motor: 1/4 HP @ 120V Installation Instructions WARNINGS AND CAUTIONS: WARNINGS AND CAUTIONS: • To be installed and/or used in accordance with appropriate electrical codes and regulations. • If you are unsure about any part of these instructions, consult a qualified electrician.
PAGE 2
Step 3b cont'd • Clear Mode • 1 Red flash = no learned devices • 1 Green flash = devices exist • Press and hold the switch pad for >5 seconds. After the button is released, the LED will flash red to confirm all learned devices have been installed. • Proceed to Step 4. Step 4 Testing your Switch prior to mounting in wall box: • Position all wires to provide room in outlet wall box for device. Step 6 Restore Power: Restore power at circuit breaker or fuse. Installation is complete.
PAGE 3
FOLD SCHEME 14" Cat No. LEVITON INSTRUCTION SHEET/MANUAL SPECIFICATIONS PK93663-10-00-0A DI-000-VZS15-02C 8.5" Black Helvetica 40 Lb. offset Paper size: 2.3" Overall size: 14" X 8.5" Final fold size: 2.3" X 4.25" Cat No. DOCUMENTATION 4.