Installation Guide

PK-A3154-10-01-0F AR2692
ENGLISHINSTALLATION INSTRUCTIONS
• TO AVOID FIRE, SHOCK, OR DEATH, UNPLUG CORD OR TURN OFF
POWER at circuit breaker or fuse and test that power is off before wiring!
• To be installed and/or used in accordance with approopiate electrical
codes and regulations.
Heavy Duty Plug - Cat. No. 115PR, Heavy Duty Cord Outlet -
Cat. No. 115CR, Plug - Cat. No. 115PV, Cord Outlet - Cat. No. 115CV -
Rated: 15A-125V
Use with Vacuum Cleaner Cord, Jr. Hard Service Cord; 18/3 to 12/3
AWG 0.240"-0.655" dia. max. STRANDED COPPER WIRE ONLY!
To Wire:
WARNING: TO AVOID FIRE, SHOCK, OR DEATH, unplug cord or turn off
power at circuit breaker or fuse and test that power is off before wiring!
1. Loosen assembly screws in face and separate device. If needed, back
out cord clamp screws enough to allow cord to fit between the two clamp
halves. Insert cord through cord clamp and housing.
2. Strip cord jacket 7/8" from cord's end. Remove insulation exposing 3/8"
bare copper wire (see diagram 1a). Twist wire strands tightly together.
Trim off cord fillers, if any.
3. Insert bare copper wire into wire clamp and tighten each terminal screw
10-12 in-lbs. torque. Ensure insulation clears clamp; HOT conductor to
BRASS terminal and NEUTRAL conductor to SILVER terminal.
4. Assemble wired device body with housing. Align keyed housing with key
on device's body. Tighten assembly screws.
5. Alternately tighten cord clamp screws 10-12 in-lbs. torque. Ensure cord
clamp rests over cord jacket, not over conductors.
Heavy Duty Grounding Plug - Cat. No. 515PR, Heavy Duty Grounding
Cord Outlet - Cat. No. 515CR, Grounding Plug - Cat. No. 515PV,
Grounding Cord Outlet - Cat. No. 515CV - Rated: 15A-125V
Use with Vacuum Cleaner Cord, Jr. Hard Service Cord; 18/3 to 12/3
AWG 0.240”-0.655” dia. max. STRANDED COPPER WIRE ONLY!
To Wire:
WARNING: TO AVOID FIRE, SHOCK, OR DEATH, unplug cord or turn off
power at circuit breaker or fuse and test that power is off before wiring!
Plugs and Connectors
2-Pole, 2-Wire / 2-Polos, 2-Cables
115PR
Cord Clamp/Abrazadera
Housing/Armazón
Body/Cuerpo
115PV
Cord Clamp/Abrazadera
Housing/Armazón
Body/Cuerpo
115CV
Cord Clamp/Abrazadera
Housing/Armazón
Body/Cuerpo
115CR
Cord Clamp/Abrazadera
Housing/Armazón
Body/Cuerpo
2-Pole, 3-Wire / 2-Polos, 3-Cables
515PR
Cord Clamp/Abrazadera
Housing/Armazón
Body/Cuerpo
515CR
Cord Clamp/Abrazadera
Housing/Armazón
Body/Cuerpo
515PV
Cord Clamp/Abrazadera
Housing/Armazón
Body/Cuerpo
515CV
Cord Clamp/Abrazadera
Housing/Armazón
Body/Cuerpo
515PA
Cord Clamp/Abrazadera
Housing/Armazón
Body/Cuerpo
515CA
Cord Clamp/Abrazadera
Housing/Armazón
Body/Cuerpo
Grounding Angle Plug; Cat. No. 515AN - Rated: 15A-125V
Use with Vacuum Cleaner Cord, Jr. Hard Service Cord; 18/3 to 12/3
AWG 0.240”-0.655” dia. max. STRANDED COPPER WIRE ONLY!
To Wire:
WARNING: TO AVOID FIRE, SHOCK, OR DEATH, unplug cord or turn off
power at circuit breaker or fuse and test that power is off before wiring!
1. Loosen assembly screws in face and separate device. Loosen clamp
screws to disassemble clamp.
2. Strip cord jacket between 1-1/8” and 1-1/4” from cord’s end. Cut
GROUND conductor to 3/4” length. Remove insulation exposing between
3/8” and 1/2” bare copper wire on all 3 conductors (see diagram 3a).
Twist wire strands tightly together. Trim off cord fillers, if any.
3. Insert bare copper wire into wire clamp and tighten each terminal screw
10-12 in-lbs. torque. Ensure insulation clears clamp. FIRST connect
GROUND conductor to GREEN hex screw, HOT conductor to BRASS
terminal and NEUTRAL conductor to SILVER terminal.
4. Assemble wired device body with housing. Align keyed housing with key
on device’s body. Tighten assembly screws.
5. Alternately tighten cord clamp screws 10-12 in-lbs. torque. Ensure cord
clamp rests over cord jacket, not over conductors.
2-Pole, 3-Wire / 2-Polos, 3-Cables
515AN
Cord Clamp/Abrazadera
Housing/Armazón
Body/Cuerpo
1. Loosen assembly screws in face and separate device. If needed, back
out cord clamp screws enough to allow cord to fit between the two clamp
halves. Insert cord through cord clamp and housing.
2. Strip cord jacket between 7/8” and 1” from cord’s end. Remove insulation
exposing between 3/8” and 1/2” bare copper wire (see diagram 2a).
Twist wire strands tightly together. Trim off cord fillers, if any.
3. Insert bare copper wire into wire clamp and tighten each terminal screw
10-12 in-lbs. torque. Ensure insulation clears clamp; HOT conductor
to BRASS terminal, NEUTRAL conductor to SILVER terminal and
GROUND conductor to GREEN hex screw.
4. Assemble wired device body with housing. Align keyed housing with key
on device’s body. Tighten assembly screws.
5. Alternately tighten cord clamp screws 10-12 in-lbs. torque. Ensure cord
clamp rests over cord jacket, not over conductors.
Armored Plug - Cat. No. 515PA, Armored Cord Outlet - Cat. No. 515CA
Rated: 15A-125V
Use with Vacuum Cleaner Cord, Jr. Hard Service Cord; 18/3 to 12/3
AWG 0.312”-0.655” dia. max. STRANDED COPPER WIRE ONLY!
To Wire:
WARNING: TO AVOID FIRE, SHOCK, OR DEATH, unplug cord or turn off
power at circuit breaker or fuse and test that power is off before wiring!
1.
Loosen assembly screws in face to separate device. If needed, back out
cord clamp screws enough to allow cord to fit between the two clamp
halves. Insert cord through cord clamp and housing.
2.
Strip cord jacket between 7/8” and 1” from cord’s end. Remove insulation
exposing between 3/8” and 1/2” bare copper wire (See diagram 2a).
Twist wire strands tightly together. Trim off cord fillers, if any.
3.
Insert bare copper wire into wire clamp and tighten each terminal screw
10-12 in-lbs. torque. Ensure insulation clears clamp; HOT conductor
to BRASS terminal, NEUTRAL conductor to SILVER terminal and
GROUND conductor to GREEN hex screw.
4.
Assemble wired device body with housing. Align keyed housing with key
on device’s body. Tighten assembly screws.
5.
Alternately tighten cord clamp screws 10-12 in-lbs. torque. Ensure
cord clamp rests over cord jacket, not over conductors. CORD
JACKET MUST BE CUT TO SPECIFIED LENGTH ONLY. IT MUST
ALWAYS REST INSIDE THE HOUSING AND UNDER CORD CLAMP;
OTHERWISE, DANGER OF AN ELECTRICAL SHORT EXISTS.
For Technical Assistance Call: 1-800-824-3005 (U.S.A. Only) www.leviton.com
LIMITED 2 YEAR WARRANTY AND EXCLUSIONS
Leviton warrants to the original consumer purchaser and not for the benefit of anyone
else that this product at the time of its sale by Leviton is free of defects in materials
and workmanship under normal and proper use for two years from the purchase date.
Leviton’s only obligation is to correct such defects by repair or replacement, at its option.
For details visit www.leviton.com or call 1-800-824-3005. This warranty excludes
and there is disclaimed liability for labor for removal of this product or reinstallation. This
warranty is void if this product is installed improperly or in an improper environment,
overloaded, misused, opened, abused, or altered in any manner, or is not used under
normal operating conditions or not in accordance with any labels or instructions.
There are no other or implied warranties of any kind, including merchantability
and fitness for a particular purpose, but if any implied warranty is required by the
applicable jurisdiction, the duration of any such implied warranty, including merchantability
and fitness for a particular purpose, is limited to two years. Leviton is not liable for
incidental, indirect, special, or consequential damages, including without limitation,
damage to, or loss of use of, any equipment, lost sales or profits or delay or
failure to perform this warranty obligation. The remedies provided herein are the
exclusive remedies under this warranty, whether based on contract, tort or otherwise.
FOR CANADA ONLY
For warranty information and/or product returns, residents of Canada should
contact Leviton in writing at Leviton Manufacturing of Canada Ltd to the
attention of the Quality Assurance Department, 165 Hymus Blvd, Pointe-
Claire (Quebec), Canada H9R 1E9 or by telephone at 1 800 405-5320.