Instructions / Assembly

DALI
®
Loop Power Pack
Cat. No. CD100
110mA output max., 12VDC nominal
For use with DALI
®
Dimming/Scene Controller
DI-000-CD100-00F
ENGLISHINSTALLATION INSTRUCTIONS
WARNINGS AND CAUTIONS
TO AVOID FIRE, SHOCK, OR DEATH; TURN OFF POWER at circuit breaker or fuse and test that power is off before wiring, servicing fixture or changing lamps.
To be installed and/or used in accordance with appropriate electrical codes and regulations.
If you are not sure about any part of these instructions, consult an electrician.
This device can be wired either as a Class 1 or Class 2 wiring device. Be sure to install in the same manner as the other devices on the DALI
®
loop.
When in doubt, install as a Class 1 wiring device. Consult local building codes and regulations for proper low-voltage installation.
A maximum of 2 Power Packs can be added in parallel as long as the total current supply
on a single loop is below 250mA
Control wiring can be Class 1 or Class 2 installed
Polarity-independent control wiring
Flexible 2-wire DALI
®
loop control wiring – Daisy Chain, Point to Point, Star or Mix Method
Input Voltage: 120/277VAC ± 10%
DALI
®
Output Voltage: 12VDC nominal
DALI
®
Output Current: 110mA
Approved for Class I or II control wiring
Leviton’s DALI
®
Loop Power Pack, Cat. No. CD100, provides power to a DALI
®
network. The DALI
®
Loop Power Pack is part of Leviton’s DALI
®
compatible products and can be
used with Leviton’s CD250 Controller or other DALI
®
compatible controls and ballasts. Installation and information for the Controller is provided in the Controller Instruction Sheet.
A single Power Pack can provide 110mA of power, which would be used by a combination of DALI
®
compatible controllers and ballasts. Use the following rule to determine the
number of controllers and ballasts that can be powered by one Power Pack. For reference, a Leviton DALI
®
Dimming/Scene Controller (CD250) consumes a maximum of 10mA of
power and a DALI
®
ballast consumes up to a maximum of 2mA.
No. of DALI
®
controllers x Current Consumption (10mA for Leviton’s CD250)
+
No. of DALI
®
ballasts x 2mA
<
110mA
If more current is required, one other Leviton DALI
®
Loop Power Pack can be added in parallel to a single DALI
®
network, which would bring the total current supply to 220mA
(refer to Wiring Diagram 2 for dual Power Pack application). Please note that the total current supply on a DALI
®
loop cannot exceed 250mA.
The Power Pack is mounted directly to a junction box (refer to Figure 1). The unit must be installed in a properly grounded metal 4" (10.16 cm) outlet box, a minimum
of 2 1/8" (5.39 cm) deep. All Class 2 (low-voltage) wiring must be contained within the Class 2 compartment (the area enclosed by the isolation barrier - refer to Figure 2).
All Class 1 (high-voltage) wiring must be contained within the Class 1 compartment (refer to Figure 2). Install or rearrange circuit wiring so all high-voltage circuit and load wires
enter the box from one side, and all low-voltage wires enter from the other.
FEATURES SPECIFICATIONS
DESCRIPTION
Figure 1 Figure 2
CD100
4" square
elecrical
box
4.10" (104.1mm)
4.10
"
(104.1mm)
1.63
"
(41.4mm)
THIS
COMPA RTMENT
FOR CLASS TWO
WIRING ONLY
Low
voltage
leads
Low voltage
compartment
cover
Insulation
barrier
High voltage
leads
DI-000-CD100-00F© 2016 Leviton Mfg. Co., Inc. For Technical Assistance Call: 1-800-824-3005 (U.S.A. Only) www.leviton.com
LIMITED 2 YEAR WARRANTY AND EXCLUSIONS
Leviton warrants to the original consumer purchaser and not for the benefit of anyone else that this product at the time of its sale by Leviton is free of defects in materials and workmanship under normal and proper
use for two years from the purchase date. Leviton’s only obligation is to correct such defects by repair or replacement, at its option. For details visit www.leviton.com or call 1-800-824-3005. This warranty
excludes and there is disclaimed liability for labor for removal of this product or reinstallation. This warranty is void if this product is installed improperly or in an improper environment, overloaded, misused,
opened, abused, or altered in any manner, or is not used under normal operating conditions or not in accordance with any labels or instructions. There are no other or implied warranties of any kind, including
merchantability and fitness for a particular purpose, but if any implied warranty is required by the applicable jurisdiction, the duration of any such implied warranty, including merchantability and fitness for a
particular purpose, is limited to two years. Leviton is not liable for incidental, indirect, special, or consequential damages, including without limitation, damage to, or loss of use of, any equipment,
lost sales or profits or delay or failure to perform this warranty obligation. The remedies provided herein are the exclusive remedies under this warranty, whether based on contract, tort or otherwise.
FOR CANADA ONLY
For warranty information and/or product returns, residents of Canada should contact Leviton in writing at Leviton Manufacturing of Canada Ltd to the attention of the Quality
Assurance Department, 165 Hymus Blvd, Pointe-Claire (Quebec), Canada H9R 1E9 or by telephone at 1 800 405-5320.
DALI is a registered trademark of ZVEI

Summary of content (2 pages)