Instructions / Assembly

Single Pole (One location) or 3-Way (Multi-location)
Quiet Fan Speed Control
Cat. No. DDF01-BL
1.5A -120VAC, 60Hz
INSTALLATION INSTRUCTIONS
For non-standard wiring applications, refer
to Wire Connector and Conductor Size Chart
1 - #12 w/ 1 to 3 #14, #16 or #18
2 - #12 w/ 1 or 2 #16 or #18
1 - #14 w/ 1 to 4 #16 or #18
2 - #14 w/ 1 to 3 #16 or #18
WIRE CONNECTOR / # OF COND.
COMBINATION CHART
DI-000-DDF01-02A
TOOLS NEEDED FOR YOUR FAN SPEED CONTROL
Slotted/Phillips Screwdriver Electrical Tape Pliers
Pencil Cutters Ruler
If installing the Fan Speed Control in a single device application,
proceed with the INSTALLING YOUR FAN SPEED CONTROL section.
If installing Fan Speed Control in a multi-device application, proceed
as follows:
INSTALLING FAN SPEED CONTROL BY ITSELF OR
WITH OTHER DEVICES
Changing the color of your Fan Speed Control:
Your device may include color options. To change color of the face
proceed as follows:
1
2
Insert top tabs and
press in bottom tabs
to attach
Push in sides at bottom
tabs and pull outward to
release
• Pull off pre-cut insulation from fan speed control leads.
• Make sure that the ends of the wires from the wall box are straight
(cut if necessary).
• Remove insulation from each wire in the wall box as shown.
• For Single-Pole Application, go to Step 4a.
• For 3-Way Matching Remote (w/LEDs) Application, go to Step 4b.
Cut
(if necessary)
5/8"
(1.6 cm)
Strip Gage
(measure bare
wire here)
Preparing and connecting wires:
Pull off pre-cut insulation from fan speed control leads. Make
sure that the ends of the wires from the wall box are straight
(cut if necessary). Remove insulation from each wire in the
wall box as shown:
Step 3
MULTI-DEVICE APPLICATION
In multi-fan speed control installations, there is no derating necessary.
Refer to the chart for maximum load per fan speed control.
INSTALLING YOUR FAN SPEED CONTROL
NOTE: Use check boxes when Steps are completed.
ONOFF
ONOFF
ONOFF
ONOFF
ONOFF
ONOFF
ONOFFONOFF
ONOFF
ONOFF
ONOFF
ONOFF
WARNING: TO AVOID FIRE SHOCK OR DEATH; TURN
OFF POWER at circuit breaker or fuse and test that power
is off before wiring!
Step 1
Step 2
Identifying your wiring application (most common):
NOTE: If the wiring in your wall box does not resemble any
of these configurations, consult an electrician.
2
4
3
1
Single Pole
1. Line (Hot)
2. Neutral
3. Ground
4. Load
3-Way
1. Line or Load
(see important
instruction)
2. Neutral
3. Ground
4. First Traveler – note color
5. Second Traveler – note color
2
4
1
5
3
IMPORTANT: For 3-Way applications, note that one of the screw
terminals from the old switch being removed will usually be a different
color (Black) or labeled Common. Tag that wire with electrical tape and
identify as the common (Line or Load) in both the fan speed control wall
box and remote wall box.
MAXIMUM LOAD PER FAN SPEED CONTROL FOR MULTI-DEVICE
More than 2 Devices
1.5A
Two Devices
1.5A
Single
1.5A
Cat. No.
DDF01
INTRODUCTION
The next generation of fan speed control technology is here with the
new Decora Digital fan speed control with Bluetooth
®
technology. This
innovative device works using the Leviton Decora Digital Dimmer &
Timer app that can be easily downloaded to smartphones or tablets
and paired to the Leviton Fan Speed Control using Bluetooth
®
technology. Decora Digital devices give users point-to-point local
control to automate lighting and fan speed control, bridging the gap
between standard dimmers, fan speed controls and whole-house
automation systems.
The Decora Digital fan speed control is a powerful device – combining
the best of Leviton fan speed functions with today’s mobile technology
for impressive results. The simple touch of a finger following the
intuitive on-screen guide makes it more convenient than ever to
manage fan speed.
Use of the app allows greater flexibility for accurate fan speed
functionality and makes pushing buttons for timed events a tedious
chore of the past.
The Leviton Decora Digital Dimmer & Timer app can be easily
downloaded to mobile devices and is compatible with Android and iOS
smartphones or tablets. The app is easy to use with simple, intuitive
on-screen menu options to independently control dimmers and
switches throughout the home.
Decora Digital devices are ideal for living rooms, bedrooms, kitchens,
dining rooms, home offices or anywhere full control of fan speed is
desired.
Compatibility:
Requires device with Bluetooth
®
4.0 (BT LE) or later and iOS 6.0 and
later. Compatible with iPhone, iPad, and iPod touch or Android 4.0 and
later.
• ON/OFF LED and fan speed level LED
• Three way communication
• Ease of installation – No new wiring
FEATURES
Fan Speed Control
Insulating
Label
Hot (Black)Black
Line
120 VAC,
60Hz
Neutral (White)
Red
Yellow/Red
White
Black
White
Green
Ground
White
Red
Green
Black
1
4
2
3
Insulating label:
This wire is used in 3-way installations only.
For single pole installations, do not remove insulating label.
Yellow/Red
Single Pole Wiring Application:
Step 4a
WIRING FAN SPEED CONTROL:
Connect wires per WIRING DIAGRAM as follows:
NOTE: The DDF01 Fan Speed Control requires a neutral wire connection.
• Green or bare copper wire in wall box to Green fan speed control lead.
• Line Hot wall box wire to Black fan speed control lead.
• Load wall box wire to Red fan speed control lead.
• Line Neutral wall box wire to White fan speed control lead.
• Yellow/Red fan speed control lead should have Red insulation
label affixed.
NOTE: If insulating label is not affixed to Yellow/Red fan speed control
lead, use electrical tape to cover.
• Proceed to Step 5.
WARNINGS AND CAUTIONS:
• TO AVOID FIRE, SHOCK, OR DEATH: TURN OFF POWER at circuit breaker or fuse and test that power is off before wiring or servicing fixture!
• TO AVOID FIRE, SHOCK, OR DEATH: this control is to be used with ceiling fans that are rated 120VAC, total load 1.5 Amperes maximum.
• To be installed and/or used in accordance with appropriate electrical codes and regulations.
• If you are unsure about any part of these instructions, consult an electrician.
• Use this device with copper or copper clad wire only.
• The Decora
®
DDF01 fan speed control is not compatible with standard 3-way or 4-way switches. It must be used with a Decora Digital remote for multi-location control, such as the DD00R-DL.
• Maximum wire length from fan speed control to all installed remotes cannot exceed 300 ft.
WARNINGS AND CAUTIONS:
• For use on ceiling paddle fans with split-capacitor or shaded pole motors only. Please refer to manufacturer’s instructions or rating label on the motor to confirm type. Use with any other
types of motors or equipment may cause overheating and/or damage to the motors or equipment.
• Use only one (1) Fan Speed Control per load. The switch(es) will turn ON the fan at the speed level selected at the control.
• To avoid overheating and possible damage to this device and other equipment, DO NOT install to control a receptacle, fluorescent lighting, a motor or a transformer-operated appliance
other than appropriate ceiling fans.
WIRING MATCHING REMOTE (wall box with line hot
connection):
Connect wires per WIRING DIAGRAM as follows:
NOTE: The matching remote must be installed in a wall box with a Line
Hot connection and a Neutral connection. A Neutral wire to the matching
remote needs to be added as shown.
NOTE: Maximum wire length from fan speed control to all installed
remotes cannot exceed 300 ft (90 m).
• Green or bare copper wire in wall box to Green terminal screw.
• Line Hot (common) wall box wire identified (tagged) when removing old
switch and First Traveler to Remote terminal marked "BK".
• Second Traveler wall box wire from fan speed control to remote terminal
screw marked "YL/RD" (note wire color). This traveler from the remote
must go to Yellow/Red fan speed control lead.
• Line Neutral wall box to remote terminal screw marked "WH".
WIRING FAN SPEED CONTROL (wall box with load
connection):
Connect wires per WIRING DIAGRAM as follows:
NOTE: The DDF01 fan speed control must be installed in a wall box that
has a Load connection and a Neutral connection.
• Green or bare copper wire in wall box to Green fan speed control lead.
• Load wall box wire identified (tagged) when removing old switch to Red
fan speed control lead.
• First Traveler Line Hot to Black fan speed control lead.
• Remove Red insulating label from Yellow/Red fan speed control lead.
• Second Traveler wall box wire (note color as above) to
Yellow/Red fan speed control lead. This traveler from the fan speed
control must go to the terminal screw on the remote marked "YL/RD".
• Line neutral wall box wire to White fan speed control lead.
• Proceed to Step 5.
Hot (Black)
Neutral (White)
Fan Speed Control
Matching Remote (w/LEDs)
YL/RD
Red
Yellow/
Red
WH BK
Black
Black
White
Line
120VAC, 60Hz
Green
Ground
Green
Ground
White
Step 4b
3-Way Wiring with DD00R Matching Remote
(w/LEDs) Application:
Matching Remote Fan Speed Control
Additional Neutral Wire
White
Red
Green
1
2
3
Yellow/Red
4
5
1
2
3
4
5
Black
NOTE: The locator light will illuminate when
the load is in the OFF position to facilitate
access in the dark.
NOTE: If using the fan speed control in a
3-way application, the fan will turn ON at the
speed set on fan speed control bar. The fan
can be controlled from either the fan speed
control, the remote location or the mobile
device app.
Rocker (Default settings)
Turn ON from OFF position:
Tap TOP of Rocker: Fan turns ON to preset
level.
Turn OFF from ON position:
Tap BOTTOM of Rocker. Fan turns OFF.
OPERATION
LED Fan Speed
Display
Fan Speed
Bar
Rocker
Locator
Light
• Restore power at circuit breaker or fuse.
• Press pad until locator light is OFF. Fan
should turn ON. If the fan does not turn
ON, press the TOP half of the Fan Speed
Bar until the fan speed increases.
If the fan still does not turn ON, refer to
the TROUBLESHOOTING section.
Testing your Fan Speed Control prior to
mounting in wall box:
Step 5
• Position all wires to provide room
in outlet wall box for device.
• Ensure that the word “TOP” is
facing up on device strap.
• Partially screw in mounting screws
in wall box mounting holes.
NOTE: Dress wires with a bend as
shown in diagram in order to relieve
stress when mounting device.
Fan Speed Control Mounting:
TURN OFF POWER AT
CIRCUIT BREAKER OR FUSE.
Step 6
Installation may now be completed by
tightening mounting screws into wall box.
Attach wallplate.
Restore Power:
Restore power at circuit breaker or fuse.
Installation is complete.
Step 7
N OTE: To pair your fan speed control with your mobile device,
download the Leviton Decora Digital Dimmer and Timer app from the
Google Play Store or your iTunes account. Contact Leviton’s Techline
at 1-800-824-3005 or visit Leviton’s website at www.leviton.com for
additional information.