Installation Guide

ManualsBrandsLeviton ManualsElectrical15 Amp Self-Test SmartlockPro Slim Duplex GFCI Outlet, Ivory

Procedure:

(a) This GFCI is shipped from the factory in the tripped condition and cannot be reset until it is wired

correctly and power is supplied to the device. Plug a lamp or radio into the GFCI (and leave it plugged

in). Turn the power ON at the service panel. Ensure that the GFCI is still in the tripped condition

by pressing the TEST button. If the lamp or radio is OFF, and the GFCI will not reset, go to the

Troubleshooting section as the Line and Load connections are reversed.

(b) Press the RESET button fully and release. If the Status Indicator Light turns Green and the lamp or

radio is ON, the GFCI has been installed correctly. If the Status Indicator Light turns or continuously

blinks Red, or the GFCI cannot be reset, go to the Self-Test Operation section.

one(s), in addition to the GFCI, lose power when you press the GFCI TEST button. Place a "GFCI

PROTECTED OUTLET" sticker on every receptacle that lost power, then press the RESET button to

reset the GFCI. DO NOT plug life saving devices into any of the receptacles that lost power.

(d) Press the TEST button (then RESET button) every month to assure proper operation. If the Status

Indicator Light does not turn Green when the RESET button is depressed and then released, or the

GFCI cannot be reset, it must be replaced.

CHARGE

LOAD

LIGNE

LINE

WHITE WIRE

FIL BLANC

HOT WIRE

FIL ACTIF

Black

White

CHARGE

LOAD

LIGNE

LINE

WHITE WIRE

FIL BLANC

HOT WIRE

FIL ACTIF

Grounding

connection to

box (if box has a

grounding terminal)

Wire

Connector

LINE cable brings

power to the GFCI

Electrical

Box

Yellow

sticker

remains

in place

to cover

the LOAD

terminals

SELF-TEST OPERATION

• A Self-Test GFCI receptacle has all the features of a conventional GFCI receptacle. In addition, this receptacle tests itself periodically to conﬁrm

the GFCI electronics are functional. The Status Indicator Light will be solid green when the GFCI is powered from Line side and working correctly.

• Self-Test Indications: If the Status Indicator Light is solid or ﬂashing RED a problem may exist. Press the TEST button to trip the GFCI. If unable

to Reset, replace the GFCI. NOTE: The status indicator may ﬂash Red at power "ON" and Reset.

Black

White

CHARGE

LOAD

LIGNE

LINE

WHITE WIRE

FIL BLANC

HOT WIRE

FIL ACTIF

LINE cable brings power to the GFCI

Electrical

Box

Wire

Connector

Grounding connection

to box (if box has a

grounding terminal)

For Back wire -

Insert bare wire fully and

tighten terminal clamp on

conductor ONLY

7. Connect the wires (choose A or B)... only after reading other side completely

RESET

TEST

RESET

TEST

RESET

TEST

RESET

Connect the LINE cable wires to the LINE terminals:

• The white wire connects to the WHITE terminal (Silver)

• The black wire connects to the HOT terminal (Brass or Black)

Connect the LOAD cable wires to the LOAD terminals:

• Remove the YELLOW sticker to reveal the LOAD terminals

• The white wire connects to the WHITE terminal (Silver)

• The black wire connects to the HOT terminal (Brass or Black)

Connect the grounding wires (only if there is a grounding wire):

•

Connect a 6-inch bare copper (or GREEN) 12 or 14 AWG wire to the grounding terminal on the

GFCI. If the box has a grounding terminal, also connect a similar wire to the grounding terminal

on the box. Connect the ends of these wires to the LINE or LOAD cable's bare copper (or

GREEN) wire using a wire connector. If these wires are already in place, check the connections.

Complete the installation:

• Fold the wires into the box, keeping the grounding wire away from the WHITE and HOT

terminals. Screw the receptacle to the box and attach the faceplate.

• Go to step 8.

Back Wire:

TROUBLESHOOTING

Turn the power OFF and check the wire connections against the appropriate wiring diagram in step 7A or 7B. Make sure that

there are no loose wires or loose connections. If the Status Indicator Light is not ON and the device is unable to reset this

could be a result of no power available. Start the test from the beginning of step 8 if you rewired any connections to the GFCI.

PK-93792-10-00-2A

Wire

5/8" (1.6 cm)

About Wire Connections:

Side Wire:

CHARGE

LOAD

LIGNE

LINE

WHITE WIRE

FIL BLANC

HOT WIRE

FIL ACTIF

For Back wire -

Insert bare wire fully

and tighten terminal

clamp on conductor

ONLY

Wire

3/4" (1.9 cm)

Back Wire:

Wire

5/8" (1.6 cm)

For Side wire -

Loop clockwise 2/3 of the

way around screw

For Side wire -

Loop clockwise 2/3 of the

way around screw

Wire

3/4" (1.9 cm)

About Wire Connections:

Side Wire:

LOAD cable feeds

power to other

receptacle(s)

This product is covered by U.S. Patent Nos. 6,040,967; 6,246,558**; 6,282,070; 6,381,112; 6,437,953; 6,646,838; 6,657,834; 6,788,173; 6,864,766**; 6,944,001; 7,336,458;

7,355,117*; 7,400,479; 7,463,124**; 7,697,252; 7,737,809**; 7,764,151**; 7,820,909*; 7,868,719

†

; 7,907,371; 8,004,804; 8,054,595; 8,130,480; 8,242,362*; 8,587,914**; 8,599,522

and corresponding foreign patents (*applies only to Cat. Nos. GFTR1, GFTR2, GFWT1 & GFWT2,

†

applies only to Cat. Nos. GFTR2 & GFWT2, **does not apply to Cat. No. GFRBF).

FOR CANADA ONLY

For warranty information and/or product returns, residents of Canada should contact Leviton in writing at Leviton Manufacturing of Canada Ltd to the

attention of the Quality Assurance Department, 165 Hymus Blvd, Pointe-Claire (Quebec), Canada H9R 1E9 or by telephone at 1 800 405-5320.

For Technical Assistance Call: 1-800-824-3005 (U.S.A. Only)

1 800 405-5320 (Canada Only) www.leviton.com

SmartlockPro is a Trademark of Leviton Manufacturing Co., Inc. registered in the United

States, Canada, Mexico and China.

Self Test Cat. No. Description

GFNT1 15A-125VAC, 60Hz Non-Tamper Resistant GFCI

GFNT2

20A-125VAC, 60Hz Non-Tamper Resistant GFCI

GFTR1 15A-125VAC, 60Hz Tamper Resistant GFCI

GFTR2 20A-125VAC, 60Hz Tamper Resistant GFCI

GFWR1 15A-125VAC, 60Hz Weather Resistant GFCI

GFWR2 20A-125VAC, 60Hz Weather Resistant GFCI

GFWT1

15A-125VAC, 60Hz Weather/Tamper Resistant GFCI

GFWT2

20A-125VAC, 60Hz Weather/Tamper Resistant GFCI

GFRBF 20A-125VAC, 60Hz Blankface GFCI

All devices rated 20A feed-through

LIMITED 2 YEAR WARRANTY AND EXCLUSIONS

Leviton warrants to the original consumer purchaser and not for the beneﬁt of anyone else that this product

at the time of its sale by Leviton is free of defects in materials and workmanship under normal and proper

use for two years from the purchase date. Leviton’s only obligation is to correct such defects by repair

or replacement, at its option. For details visit www.leviton.com or call 1-800-824-3005. This warranty

excludes and there is disclaimed liability for labor for removal of this product or reinstallation. This warranty

is void if this product is installed improperly or in an improper environment, overloaded, misused, opened,

abused, or altered in any manner, or is not used under normal operating conditions or not in accordance

with any labels or instructions. There are no other or implied warranties of any kind, including

merchantability and ﬁtness for a particular purpose, but if any implied warranty is required by the

applicable jurisdiction, the duration of any such implied warranty, including merchantability and ﬁtness for

a particular purpose, is limited to two years. Leviton is not liable for incidental, indirect, special, or

consequential damages, including without limitation, damage to, or loss of use of, any equipment,

lost sales or proﬁts or delay or failure to perform this warranty obligation. The remedies provided

herein are the exclusive remedies under this warranty, whether based on contract, tort or otherwise.

Connect the LINE cable wires to the LINE terminals:

• The white wire connects to the WHITE terminal (Silver)

• The black wire connects to the HOT terminal (Brass or Black)

Connect the grounding wire (only if there is a grounding wire):

• For a box with no grounding terminal (diagram not shown): Connect

the LINE cable's bare copper (or GREEN) wire directly to the

grounding terminal on the GFCI receptacle.

• For a box with a grounding terminal (diagram shown above): Connect

a 6-inch bare copper (or GREEN) 12 or 14 AWG wire to the grounding

terminal on the GFCI. Also connect a similar wire to the grounding

terminal on the box. Connect the ends of these wires to the LINE

cable's bare copper (or GREEN) wire using a wire connector.

If these wires are already in place, check the connections.

Complete the installation:

• Fold the wires into the box, keeping the grounding wire away from the

WHITE and HOT terminals. Screw the receptacle to the box and attach

the faceplate.

• Go to step 8.

A: One Cable (2 or 3 wires) entering the box B: Two cables (4 or 6 wires) entering the box

8. Test your work

Why perform this test?

• If you miswired the GFCI it may not prevent personal injury or death due to a ground fault

(electrical shock).

• If you mistakenly connect the LINE wires to the LOAD terminals, the GFCI will not reset and will

not provide power to either the GFCI receptacle face or any receptacles fed from the GFCI.

FCC STATEMENT

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio

frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However,

there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television

reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the

following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

IC STATEMENT

This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not

cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.

WEB VERSION