Installation Guide

Hot (Black)
Neutral (White)
Dimmer
3-Way Switch
Black
White
Black
Green
Ground
Red
Line
120VAC, 60Hz
Common
Terminal
(Black Screw)
Black
White
Electronic
Low-Voltage
Transformer
Primary
Side
5. Restore power at circuit breaker or fuse. Press the ON/
OFF push-button switch several times (see Figure 1).
The GREEN LED will turn ON and OFF indicating
power to the switch. Position the slider to the minimum
brightness level (bottom of stroke).
6. The brightness adjustment is located at the top of the
dimmer back cover (see Figure 1). Using a small,
insulated screwdriver, rotate the trim adjustment until
the desired level of minimum brightness is obtained.
7. Check for proper operation by raising the slider to it’s
maximum position and returning to minimum (bottom of
stroke). If operation is not satisfactory, repeat step 6.
When the brightness level is adjusted to satisfaction,
TURN OFF POWER.
8. Installation may now be completed by carefully
positioning all wires to provide room in outlet box for
dimmer. Mount dimmer into box with mounting screws
supplied. Attach Decora
®
wallplate.
9. Restore power at circuit breaker or fuse.
INSTALLATION IS COMPLETE.
COLOR CONVERSION PROCEDURE
The color of this device can be changed to suit your
interior design requirements. Simply obtain a color
conversion kit of the appropriate color from your Leviton
distributor and proceed as follows (please note that
wallplate must be removed).
1. Select the color of the face you desire.
2. The frame has snaps on its sides. Using your fingers,
grip around the Decora
®
frame and push on one side to
release it from the strap (see Figure 2).
3. Take the new frame and position it properly to the
strap. Line up the plastic snaps with the square holes
in the strap. Insert the snaps on one side of the frame
into the strap.
4. Firmly press sideways and down to slip the other snaps
into place. The frame snaps in with a audible click.
Ensure that all four snaps are secure.
5. Moving the slider up or down will automatically engage
the slider control mechanism. Replace Decora
®
wallplate. The color conversion is complete.
TO OPERATE
• GREEN LED will remain ON when the lights are OFF
- Facilitates access to switch in the dark.
• Depress push-button switch to ON position
- Lights will turn ON (GREEN LED will turn OFF).
• Move slider - Lights will brighten or dim to level set.
• Depress push-button switch to OFF position
- Lights will turn OFF (GREEN LED will turn ON).
• Lights will turn ON at set brightness level (from either
switch location in a 3-way installation).
TROUBLESHOOTING
• Light does not turn ON and ON/OFF LED does not
turn ON
- Circuit breaker or fuse has tripped.
- Lamp is burned out.
- Lamp is not connected to line Neutral.
• Lights Flickering
- Lamp has a bad connection.
- Wires not secured firmly with wire connectors
Figure 2 - Color Conversion
Hot (Black)
Neutral (White)
Dimmer
Black
Black
Green
Ground
Black
White
Red
White
Line
120VAC, 60Hz
Cap with
Wire Connector
Electronic
Low-Voltage
Transformer
Primary
Side
Wiring Diagram 3 - Three Location Control Application
Wiring Diagram 1 - Single Location Control Application
Wiring Diagram 2 - Two Location Control Application
Hot (Black)
Neutral (White)
Dimmer
3-Way Switch
Black
Black
Green
Ground
Green
Ground
Black
White
White
Red
Line
120VAC, 60Hz
Common
Terminal
(Black Screw)
4-Way Switch
Green
Ground
1
1
Travelers between switches "IN"
Travelers between switches "OUT"
2
1
2
2
Primary
Side
Electronic
Low-Voltage
Transformer
Frame
Strap
Snaps
Push in 2 Locations
ON/OFF
LED
Slider