Instructions / Assembly

ManualsBrandsLeviton ManualsDimmersDecora SureSlide Universal 150-Watt LED/CFL Incandescent Slide-to-Off Dimmer, White (3-Pack)

Removing existing switch: Remove existing

wallplate and switch mounting screws. Carefully pull switch

from wall box. DO NOT remove wires attached to the

switch at this time.

WARNING: TO AVOID FIRE, SHOCK, OR DEATH;

TURN OFF POWER at circuit breaker or fuse and test that

power is off before wiring!

Slide Dimmer

Cat. No. 6672-L (optional locator light)

600W Incandescent, 150W Dimmable LED & CFL

INSTALLATION INSTRUCTIONS

DI-000-06672-02A

ONOFF

ONOFFONOFF

ONOFF

Single-Pole:

Look at the back of your switch.

If there are 2 wires connected

to two screw terminals (not

including a green or bare copper

wire used for grounding), you

have a Single-Pole switch.

WARNINGS AND CAUTIONS:

• TO AVOID FIRE, SHOCK, OR DEATH; TURN OFF POWER AT CIRCUIT BREAKER OR FUSE AND

TEST THAT POWER IS OFF BEFORE WIRING!

• Tobeinstalledand/orusedinaccordancewithappropriateelectricalcodesandregulations.

• Ifyouareunsureaboutanypartoftheseinstructions,consultanelectrician.

• Toavoidoverheatingandpossibledamagetothisdeviceandotherequipment,donotinstalltocontrol

a receptacle, ﬂuorescent lighting, a motor- or a transformer-operated appliance.

WARNINGS AND CAUTIONS:

• Use with compatible dimmable LED, CFL bulbs, incandescent or 120V halogen ﬁxtures only. For a

complete list of compatible LED and CFL bulbs refer to www.leviton.com.

• WhenmultiplebulbsareusedwithonedimmerDONOTmixbulbtypes.AllbulbsshallbeeitherLED;

CFLorincandescent.Usingthesamemake/modelofeachbulbwillenhancedimmerperformance.

• Use this device with copper or copper clad wire only.

Step 3

Strip Gage

Black

Neutral

Green

Ground

Insert wires

straight

then twist

clockwise

ElectricalTape

• Disconnectwiresfromscrewterminalsor

Quickwire™ slots (shown).

• Pulloffpre-cutinsulationfromDimmerleads.

Twiststrandstightlytogether.

• Makesurethattheendsofthewiresfromthe

wall box are straight (cut if necessary).

• Remove5/8"(1.6cm)ofinsulationfromeach

wire in the wall box (shown).

Press in slot and

pull out wire

Cut (if necessary)

Step 4

Disconnecting switch wires and preparing wires:

Step 2

Tools needed to install your Dimmer

Slotted/PhilipsScrewdriver ElectricalTape Pliers 

Pencil Cutters Ruler

Installing Dimmer by itself or with other devices

If installing Dimmer in a single device application, proceed with the

INSTALLING YOUR DIMMER section. If installing Dimmer in a

multi-device application, proceed as follows:

Single-Pole Wiring Application:

Connect wires per WIRING DIAGRAM as follows:

Screw wire nuts on clockwise making sure no bare conductors show below

the wire connectors. Secure each connector with electrical tape.

• Green dimmer Ground lead to Green or bare copper wire in wall box.

• Black dimmer lead to any wall box wire removed from old switch.

• Remaining Black dimmer lead to remaining wall box wire.

• ProceedtoStep6.

Step 1

Hot (Black)

Neutral (White)

Black

White

Line 120V

AC, 60 Hz

Black Black

Dimmer

Green

Ground

Load

INSTALLING YOUR DIMMER

NOTE: Use check boxes when steps are completed.

√

MULTI-DEVICE APPLICATION:

In incandescent multi-dimmer installations, the reduction of the dimmer’s

capacityisrequired.Refertothechartformaximumloadperdimmer.

NoderatingisrequiredforuseinDimmableCFLordimmableLED

multi-dimmer installations.

MAXIMUM LOAD PER DIMMER FOR MULTI-DEVICE

Cat. No. Single Two Devices More than 2 Devices

6672

600W 500W 400W

Step 5

Identifying your wiring application

(most common):

NOTE: If the wiring in the wall box does not resemble any of

these conﬁgurations, consult an electrician.

5/8"

(1.6cm)

Summary of content (2 pages)

PAGE 1
Slide Dimmer Cat. No. 6672-L (optional locator light) 600W Incandescent, 150W Dimmable LED & CFL INSTALLATION INSTRUCTIONS DI-000-06672-02A WARNINGS AND CAUTIONS: WARNINGS AND CAUTIONS: • T O AVOID FIRE, SHOCK, OR DEATH; TURN OFF POWER AT CIRCUIT BREAKER OR FUSE AND TEST THAT POWER IS OFF BEFORE WIRING! • To be installed and/or used in accordance with appropriate electrical codes and regulations. • If you are unsure about any part of these instructions, consult an electrician.
PAGE 2
Step 6 Testing your Dimmer prior to mounting in wall box: NOTE: Cat. No. 6672 is shipped with the indicator light disabled (OFF). If you want the light option (ON), with an insulated screwdriver slide the switch at the TOP of the frame to the left while facing the device before mounting wallplate. Cat. No. 6672 Indicator Slide Switch OPERATION Optional locator light: The locator light illuminates the switch when the dimmer is the OFF position. To activate, slide the selector switch to the ON position.