User Guide N3004-00D / N3008-00D (N3008-00D model shown) Document Release June 2014 Revision B
Warranty Leviton Manufacturing Co Inc. warrants this control console to be free of material and workmanship defects for a period of two years after system acceptance or 26 months after shipment, whichever comes first. This Warranty is limited to repair of replacement of defective equipment returned Freight Pre-Paid to Leviton Lighting & Energy Solutions at PO Box 2210, Tualatin, Oregon 97062, USA.
Table of Contents Chapter 1 Introduction............................................... 1 About the Console ........................................................ 2 Features ............................................................. 2 Specifications ..................................................... 2 Warnings ! ......................................................... 2 Console Controls ................................................. 3 Rear Panel ..................................................
Page ii N3004 / N3008 User Guide
Chapter 1 Introduction This chapter is intended to orient you to the Console and User Guide. The following sections are covered: • About the Console • Features • Specifications • Warnings • Console Controls • Rear Panel • Audio Sensitivity Control • Using this Guide • Text Conventions • Terminology Definitions • Contacting Technical Support Rev.
Chapter 1 Introduction About the Console The N3000 series of lighting control consoles are designed to be both simple and intuitive to operate, just plug it in and go! Features Features available depend on the model you purchased: Model N3004 N3008 Channel Faders: 04 08 Scenes: 04 08 Bump Buttons: 04 08 Chases: 02 02 Chaser Functions Chaser functions on all models include the ability to chase either factory programmed individual channel patterns or user programmed scenes.
Console Controls Rev.
Chapter 1 Introduction Rear Panel Audio Sensitivity Control Page 4 N3004 / N3008 User Guide
Using this Guide Text Conventions Fader and Button control names are shown in bolded letters and appear inside brackets [ ] . For example: Fader 1 appears as: Fader [1] The Chase 2 button appears as: [Chase 2] Terminology Definitions Channels: Channels are the most basic unit of control and are used for setting lights to various intensity levels. A channel is represented by a single fader or bump button on a control console.
Chapter 1 Introduction Page 6 N3004 / N3008 User Guide
Chapter 2 Operation The following sections are covered in this chapter: • Setting Channel Levels • Master Fader • Master Bump Button • Channel Faders • Channel Bump Buttons • Scenes • Recording Scenes • Recalling Scenes • Scene Bump Buttons • Chases • Channel Chase • Scenes Chase • Audio Chase Rev.
Chapter 2 Operation Setting Channel Levels Master Fader The Master Fader is used to proportionally control the output of all the console channels. For example, if the level of channel 1 is at 80% and the master is set at 50%, the actual output of channel 1 will be 40%. A Master Fader LED is located directly above the fader to give the user intensity feedback.
Scenes Depending on the model, up to 8 scenes may be recorded for playback. Once channel levels are recorded, the scene can be recalled by either raising the scene’s fader or pressing the corresponding bump button. Recording Scenes The following example shows how to record channels into a simple scene: Procedure: Notes: 1. Press [SC/CH] until LED is Off 2. Raise Master Fader to 100% (full) 3. Raise Faders [1] thru [4] to 100% (full) 4. Press and Hold [PROG] [PROG] LED turns On 5.
Chapter 2 Operation Chases As mentioned earlier, a Chase is a series of factory programmed individual channel patterns or user recorded scenes that can be played back in a continuous loop. The [SPEED] control adjusts the step rate of the chase which is indicated by an LED that will flash whenever the chase is activated. The direction of the chase can be reversed by pressing the [PROG] button. To black out the chase sequence, press the [BLACK] button.
Scene Chase To initiate a scene chase, record scenes 1-4 as shown in the above Recording Scenes section, then follow the example below: Procedure: Notes: 1. Press [SC/CH] until LED is On 2. Raise Master Fader to 100% (full) 3. Raise Faders 1-4 to 100% (full) 4. Press [CHASE 1] 5. Adjust [SPEED] control to set rate Scene 1-4 LED’s flash 6. Press [PROG] to reverse direction Chase 1 will activate Scenes 1-4, Chase 2 will activate scenes 5-8.
Chapter 2 Operation Page 12 N3004 / N3008 User Guide
Copyright © 2014 Leviton Manufacturing Company Incorporated. All Rights Reserved. Information contained herein is subject to change without notice. Document Release June 2014 Rev. B Leviton Lighting & Energy Solutions Division 20497 SW Teton, Tualatin, OR 97062 Mailing Address: PO Box 2210 Tualatin, OR 97062 Customer Service: (800)736-6682 Technical Support: (800)959-6004 Fax: (503)404-5601 Internet: www.leviton.
