Specification

ManualsBrandsLeviton ManualsElectricalDecora Commercial Grade Passive Infrared Single-Pole Dual Relay 2100 sq. ft. 180-Degree Occupancy Sensor, Gray

PRODUCT DATA

Leviton Mfg. Co., Inc. Lighting & Energy Solutions

201 N. Service Rd. Melville, NY 11747-3138 Tech Line: 1-800-824-3005 Fax: 1-800-832-9538 www.leviton.com/les

ODS0D

Dual-Relay Decora

Wall Switch

PIR Occupancy Sensor

BASIC OPERATION

The ODS0D uses passive infrared (PIR) technology to

monitor a room for occupancy through a segmented

Fresnel lens. This specialized lens divides the field-of-

view into sensor zones. When a person passes into or

out of a sensor zone, the sensor detects motion and

switches two separate lighting loads ON. The lights

will remain ON as long as there is an occupant moving

through the sensor zones.

The ODS0D-TD has an adjustable 30 minute time delay

setting for the first and second relay to comply with

CEC Title 24. The second relay is manual-ON only.

APPLICATIONS

Leviton’s ODS0D Dual-Relay Decora Wall Switch

Passive Infrared (PIR) Occupancy Sensor is used to

provide automatic lighting control for energy savings

and convenience in a variety of commercial applica-

tions, including:

• Classrooms • Conference rooms • Offices

• Multimedia rooms • Day care centers • Lounges

• Daylight harvesting

• Bi-level or A/B switching

The ODS0D provides automatic switching of two sepa-

rate lighting loads from a single unit. It is compatible

with incandescent, fluorescent and low-voltage light-

ing. The unit features dual manual-override switches

that can be used to toggle the ON/OFF status of each

lighting load while an area is occupied. The ODS0D can

be installed in place of two single-pole wall switches

and fits in a standard single-gang wall box. The unit

requires a ground connection for proper operation.

FEATURES

• Provides automatic switching for two separate banks

of fluorescent, incandescent, or low-voltage lighting

from a single unit.

• Convenient dual pushbuttons provide manual-ON/

OFF light switching of each load at any time.

• ODSOD-ID Conference Room Mode—primary and sec-

ondary relays switch lighting to last ON/OFF status

when personnel enter room, providing a consistent

lighting level from one occupancy period to the next.

Both relays respond to Ambient Light Override, pre-

venting lights from turning ON automatically during

periods of ample natural light, for increased energy

savings.

• ODS0D-ID Classroom Mode—both primary and sec-

ondary relays always switch lighting ON when per-

sonnel enter room, regardless of their ON/OFF status

during last period of occupancy. Secondary relay only

responds to Ambient Light Override—primary does

not, ensuring that students and personnel never

enter a darkened room.

• Presentation Mode feature for slide or film presenta-

tions allows push buttons to turn lights OFF and keep

them OFF while the room is occupied.

• Auto adapting delayed-OFF time interval compen-

sates for real-time occupancy patterns, preventing

unnecessary ON/OFF switching.

• Exclusive Walk-Through feature provides increased

energy savings by not leaving the lights ON for an

extended period after only momentary occupancy.

• Non-Adaptive Mode disables Self-Adjusting Delayed-

OFF Time and Walk-Through feature in applications

where these features are not desired.

• Daylight harvesting light sensor measures the ambi-

ent light in the room when it first detects motion. It

leaves the lights OFF if there is enough light in the

room or turns the lights connected to the first relay

ON if there is not enough light in the room.

• Low-profile design eliminates obtrusive “scanning-

device” look. Elegant Decora wallplates complement

any interior for sleek aesthetics; uses Decora wall-

plates and coordinates with Leviton’s popular line of

Decora wiring devices.

• 180° field-of-view provides approximately 2100

square feet of coverage, suitable for a variety of

commercial areas.

• Segmented Fresnel lens provides optimum sensitiv-

ity and performance. Designed with an extensive

“minor motion” area where even slight body move-

ments will be detected.

• Patented blinders: horizontal field-of-view may be

adjusted between 180° and 60° arc by using integral

blinders located on either side of the lens. No mask-

continued …

ODS0D-ID-TD

Summary of content (4 pages)

PAGE 1
PRODUCT DATA ODS0D-ID-TD BASIC OPERATION The ODS0D uses passive infrared (PIR) technology to monitor a room for occupancy through a segmented Fresnel lens. This specialized lens divides the field-ofview into sensor zones. When a person passes into or out of a sensor zone, the sensor detects motion and switches two separate lighting loads ON. The lights will remain ON as long as there is an occupant moving through the sensor zones.
PAGE 2
PRODUCT DATA ing tape required. • Time delay adjustment for delayed-OFF time settings of 30 seconds, 5, 10, and 30 minutes. Allows customized adjustments to maximize energy savings. • Vandal resistant PIR lens. • False detection circuitry. • Light Sensor adjustable Ambient Light Override ranges from approximately 2FC (20 LUX) to 500+FC (5000+ LUX). • Manual-ON/auto-OFF mode for installations where manualON switching is required but auto-OFF switching is still desired for CEC Title T24 energy savings.
PAGE 3
FIELD-OF-VIEW The ODS0D provides a 180° field-of-view with a maximum coverage area of approximately 2100 square feet. The maximum sensing distance in front of the sensor is 40 feet, and at each side is 30 feet. The “minor motion” zone detects relatively small body movements and allows the lights to stay ON even though a person may not be moving or walking around the room. The remainder of the field-of-view, the “major motion” zone, exhibits a lesser degree of sensitivity and requires larger movements.
PAGE 4
PRODUCT DATA SPECIFICATIONS DIMENSIONAL DIAGRAMS ELECTRICAL 1.75 (44.4 mm) Line Voltage 120-230-277 VAC Power Consumption 120V - 110mW 277V - 270mW Operational Frequency 50/60Hz Wire Designation Primary Relay— No. 16 AWG leads: Line—Black Load—Blue Ground—Green Secondary Relay— N0.