Instructions / Assembly

ManualsBrandsLeviton ManualsOtherDecora 600-Watt Single-Pole/3-Way Universal Rocker Slide Dimmer, Brown

Identifying your wiring application

(most common):

NOTE: If the wiring in the wall box does not resemble any of

these conﬁgurations, consult an electrician.

LED / CFL / INCANDESCENT SLIDE DIMMER

Single Pole or 3-Way

Cat. No. DSL

6 – LED/CFL 300W (2.5A), Incandescent 600W

120VAC, 60Hz

INSTALLATION INSTRUCTIONS

Tools needed to install your Dimmer

Slotted/Philips Screwdriver Electrical Tape Ruler

Pliers Pencil Cutters

LOC

OFF

LOC

OFF

Slide

Bar

Alignment

Arrow

Step 3

Changing the color of your Dimmer

If a color change kit is provided with your device, proceed with the

following step before wiring the device if you need to change the color.

Otherwise, proceed with the "Installing Dimmer by itself or with other

devices" section.

In incandescent multi-dimmer

installations, the reduction of the

dimmer’s capacity is required. Refer to

the chart for maximum load per dimmer.

No derating is required for use in

dimmable CFL or dimmable LED multi-

dimmer installations.

Installing Dimmer by itself or with other devices

Step 2

ONOFF

ONOFFONOFF

ONOFF

WARNING: TO AVOID FIRE, SHOCK, OR DEATH; TURN

OFF POWER at circuit breaker or fuse and test that power is

off before wiring or servicing ﬁxture!

Step 1

Single Pole

1. Line (Hot)

2. Neutral

3. Ground

4. Load

NOTE: For 3-Way applications, note that one of the screw terminals from

the old switch being removed will usually be a different color (Black) or

labeled Common. Tag that wire with electrical tape and identify as the

common (Line or Load) in both the dimmer wall box and 3-way wall box.

Preparing and connecting wires:

Strip gage

Cut

(if necessary)

5/8"

• Make sure that the ends of the wires from the wall box are

straight (cut if necessary).

• Remove 5/8" (1.6 cm) of insulation from each wire in the

wall box.

• For Single-Pole Application, go to Step 4a.

• For 3-Way Application, go to Step 4b.

Single-Pole Wiring Application:

Step 4a

3-Way

1. Line or Load (See note below)

2. Neutral

3. Ground

4. First Traveler – note color

5. Second Traveler – note color

DI-000-DSL06-02B

Installing your Dimmer

NOTE: Use check boxes when Steps are completed.

Terminal

Screw Marked

Black (BK)

Terminal

Screw Marked

Red (RD)

Terminal Label:

Use terminal for

3-way or more

applications only.

For single pole

applications,

DO NOT remove

this label.

Dimmer

Terminal

Screw Marked

Ground (GR)

Terminal Label:

Use terminal for

3-way or more

applications only.

For single pole

applications,

DO NOT remove

this label.

Green

Ground

BKRD

Hot (Black)

Neutral (white)

Line

120VAC, 60Hz

Dimmer

Insert top tabs of the

color kit into the slots on

the top of the dimmer.

Then press the bottom

of the color kit in until it

snaps into place.

Press the side of the

color kit at either bottom

tab and pull forward to

release.

Align slide bar with

alignment arrow as

shown. Move the slide

bar of the color kit to the

bottom.

REMOVE

REPLACE

MAXIMUM LOAD PER DIMMER FOR MULTI-DEVICE

Cat. No. Load Single Two

Devices

More than 2

Devices

DSL

6 Incand. 600W 500W 500W

DSL

6 LED/CFL 300W (2.5A) 300W (2.5A) 300W (2.5A)

WARNINGS AND CAUTIONS:

• When multiple bulbs are used with one dimmer DO NOT mix bulb types. All bulbs shall be either LED; CFL

or incandescent. Using the same make/model of each bulb will enhance performance.

• Use only one (1) dimmer in a 3 or 4-way circuit. The switch(es) will turn the light on at the brightness level selected

at the dimmer.

• To avoid overheating and possible damage to this device and other equipment, DO NOT install to control a

receptacle, a motor or a transformer-operated appliance, or any other lighting sources than those speciﬁed.

WARNINGS AND CAUTIONS:

• TO AVOID FIRE, SHOCK, OR DEATH: TURN OFF POWER at circuit breaker or fuse and test that power is off

before wiring or servicing ﬁxture!

• TO AVOID FIRE, SHOCK, OR DEATH: use with compatible dimmable LED and CFL bulbs, incandescent or 120V

halogen ﬁxtures only. For a complete list of compatible LED and CFL bulbs refer to www.leviton.com/universal.

• To be installed and/or used in accordance with appropriate electrical codes and regulations.

• If you are unsure about any part of these instructions, consult an electrician.

• Use this device with copper or copper clad wire only.

• Green or bare copper wall box wire to terminal screw marked "GR".

• Line Hot wall box wire to terminal screw marked "BK".

• Load wall box wire to terminal screw marked "RD".

• Remaining Dimmer terminal screw marked "RD" should have an

insulation label afﬁxed. DO NOT REMOVE this label in a single pole

application.

Proceed to Step 5.

Connect wires per WIRING DIAGRAM as follows:

WEB VERSION

Summary of content (2 pages)

PAGE 1
LED / CFL / INCANDESCENT SLIDE DIMMER Single Pole or 3-Way Cat. No. DSLØ6 – LED/CFL 300W (2.5A), Incandescent 600W 120VAC, 60Hz INSTALLATION INSTRUCTIONS DI-000-DSL06-02B WARNINGS AND CAUTIONS: • TO AVOID FIRE, SHOCK, OR DEATH: TURN OFF POWER at circuit breaker or fuse and test that power is off before wiring or servicing ﬁxture! • TO AVOID FIRE, SHOCK, OR DEATH: use with compatible dimmable LED and CFL bulbs, incandescent or 120V halogen ﬁxtures only.
PAGE 2
Terminal Screw Marked Black (BK) Dimmer 1 2 2 3 Black Screw (common) 3 4 3-Way Terminal Screw Marked Red (RD) 5 5 4 1 3-Way wall box: RD RD BK Line 120VAC, 60Hz Green Ground Step 7 Dimmer Mounting: TURN OFF POWER AT CIRCUIT BREAKER OR FUSE. Black Screw (common) Installation may now be completed by carefully positioning all wires to provide room in wall box for dimmer. Mount dimmer into box with mounting screws supplied. Attach wallplate.